| #Uncommenting these urls would only enable |
| #the power up auto injection and force injection(test case). |
| #XTRA_SERVER_1=http://xtrapath1.izatcloud.net/xtra2.bin |
| #XTRA_SERVER_2=http://xtrapath2.izatcloud.net/xtra2.bin |
| #XTRA_SERVER_3=http://xtrapath3.izatcloud.net/xtra2.bin |
| |
| #Version check for XTRA |
| #DISABLE = 0 |
| #AUTO = 1 |
| #XTRA2 = 2 |
| #XTRA3 = 3 |
| XTRA_VERSION_CHECK=0 |
| |
| # Error Estimate |
| # _SET = 1 |
| # _CLEAR = 0 |
| ERR_ESTIMATE=0 |
| |
| #NTP server |
| NTP_SERVER=time.izatcloud.net |
| |
| #XTRA CA path |
| XTRA_CA_PATH=/system/etc/security/cacerts |
| |
| # DEBUG LEVELS: 0 - none, 1 - Error, 2 - Warning, 3 - Info |
| # 4 - Debug, 5 - Verbose |
| # If DEBUG_LEVEL is commented, Android's logging levels will be used |
| DEBUG_LEVEL = 3 |
| |
| # Intermediate position report, 1=enable, 0=disable |
| INTERMEDIATE_POS=0 |
| |
| # Below bit mask configures how GPS functionalities |
| # should be locked when user turns off GPS on Settings |
| # Set bit 0x1 if MO GPS functionalities are to be locked |
| # Set bit 0x2 if NI GPS functionalities are to be locked |
| # default - non is locked for backward compatibility |
| #GPS_LOCK = 0 |
| |
| # supl version 1.0 |
| SUPL_VER=0x10000 |
| |
| # Emergency SUPL, 1=enable, 0=disable |
| #SUPL_ES=0 |
| |
| #Choose PDN for Emergency SUPL |
| #1 - Use emergency PDN |
| #0 - Use regular SUPL PDN for Emergency SUPL |
| #USE_EMERGENCY_PDN_FOR_EMERGENCY_SUPL=0 |
| |
| #SUPL_MODE is a bit mask set in config.xml per carrier by default. |
| #If it is uncommented here, this value will overwrite the value from |
| #config.xml. |
| #MSA=0X2 |
| #MSB=0X1 |
| #SUPL_MODE= |
| |
| # GPS Capabilities bit mask |
| # SCHEDULING = 0x01 |
| # MSB = 0x02 |
| # MSA = 0x04 |
| # ON_DEMAND_TIME = 0x10 |
| # GEOFENCE = 0x20 |
| # default = ON_DEMAND_TIME | MSA | MSB | SCHEDULING | GEOFENCE |
| CAPABILITIES=0x37 |
| |
| # Accuracy threshold for intermediate positions |
| # less accurate positions are ignored, 0 for passing all positions |
| # ACCURACY_THRES=5000 |
| |
| ################################ |
| ##### AGPS server settings ##### |
| ################################ |
| |
| # FOR SUPL SUPPORT, set the following |
| # SUPL_HOST=supl.host.com or IP |
| # SUPL_PORT=1234 |
| |
| # FOR C2K PDE SUPPORT, set the following |
| # C2K_HOST=c2k.pde.com or IP |
| # C2K_PORT=1234 |
| |
| # Bitmask of slots that are available |
| # for write/install to, where 1s indicate writable, |
| # and the default value is 0 where no slots |
| # are writable. For example, AGPS_CERT_WRITABLE_MASK |
| # of b1000001010 makes 3 slots available |
| # and the remaining 7 slots unwritable. |
| #AGPS_CERT_WRITABLE_MASK=0 |
| |
| #################################### |
| # LTE Positioning Profile Settings |
| #################################### |
| # 0: Enable RRLP on LTE(Default) |
| # 1: Enable LPP_User_Plane on LTE |
| # 2: Enable LPP_Control_Plane |
| # 3: Enable both LPP_User_Plane and LPP_Control_Plane |
| LPP_PROFILE = 2 |
| |
| ################################ |
| # EXTRA SETTINGS |
| ################################ |
| # NMEA provider (1=Modem Processor, 0=Application Processor) |
| NMEA_PROVIDER=0 |
| # Mark if it is a SGLTE target (1=SGLTE, 0=nonSGLTE) |
| SGLTE_TARGET=0 |
| |
| ################################################## |
| # Select Positioning Protocol on A-GLONASS system |
| ################################################## |
| # 0x1: RRC CPlane |
| # 0x2: RRLP UPlane |
| # 0x4: LLP Uplane |
| A_GLONASS_POS_PROTOCOL_SELECT = 0 |
| |
| ################################################## |
| # Select technology for LPPe Control Plane |
| ################################################## |
| # 0x1: DBH for LPPe CP |
| # 0x2: WLAN AP Measurements for LPPe CP |
| LPPE_CP_TECHNOLOGY = 0 |
| |
| ################################################## |
| # Select technology for LPPe User Plane |
| ################################################## |
| # 0x1: DBH for LPPe UP |
| # 0x2: WLAN AP Measurements for LPPe UP |
| LPPE_UP_TECHNOLOGY = 0 |
| |
| # AP Coarse Timestamp Uncertainty |
| ################################################## |
| # default : 10 |
| # or as per clock uncertainty of product |
| AP_TIMESTAMP_UNCERTAINTY = 10 |
| |
| ##################################### |
| # GNSS PPS settings |
| ##################################### |
| #AP DR engine availability status |
| # 0 : NO AP DR (default) |
| # 1 : AP DR enabled |
| #EXTERNAL_DR_ENABLED = 0 |
| |
| ##################################### |
| #DR_SYNC Pulse Availability |
| ##################################### |
| # 0 : DR_SYNC pulse not available (default) |
| # 1 : DR_SYNC pulse available |
| DR_SYNC_ENABLED = 0 |
| |
| ##################################### |
| #PPS Device name |
| ##################################### |
| PPS_DEVICENAME = /dev/pps0 |
| |
| ##################################### |
| #AP Clock Accuracy |
| ##################################### |
| AP_CLOCK_PPM = 100 |
| |
| ##################################### |
| #MAX ms difference to detect missing pulse |
| ##################################### |
| MISSING_PULSE_TIME_DELTA = 900 |
| |
| ##################################### |
| #Propagation time uncertainty |
| ##################################### |
| PROPAGATION_TIME_UNCERTAINTY = 1 |