tetheroffload/control/1.1/IOffloadControl.hal

/*
 * Copyright (C) 2020 The Android Open Source Project
 *
 * Licensed under the Apache License, Version 2.0 (the "License");
 * you may not use this file except in compliance with the License.
 * You may obtain a copy of the License at
 *
 *      http://www.apache.org/licenses/LICENSE-2.0
 *
 * Unless required by applicable law or agreed to in writing, software
 * distributed under the License is distributed on an "AS IS" BASIS,
 * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
 * See the License for the specific language governing permissions and
 * limitations under the License.
 */

package android.hardware.tetheroffload.control@1.1;

import @1.0::IOffloadControl;

/**
 * Interface used to control the lifecycle of tethering offload. Note that callbacks of 1.1 HAL
 * can be registered with the existing callback registration methods from 1.0 HAL.
 */
interface IOffloadControl extends @1.0::IOffloadControl {
    /**
     * Instruct hardware to send callbacks after certain number of bytes have been transferred in
     * either direction on this upstream interface.
     *
     * The specified quota bytes must be applied to all traffic on the given upstream interface.
     * This includes hardware forwarded traffic, software forwarded traffic, and AP-originated
     * traffic. IPv4 and IPv6 traffic both count towards the same quota. IP headers are included
     * in the byte count quota, but, link-layer headers are not.
     *
     * This API may only be called while offload is occurring on this upstream. The hardware
     * management process MUST NOT store the values when offload is not started and applies once
     * offload is started. This is because the quota values would likely become stale over
     * time and would not reflect any new traffic that has occurred.
     *
     * This API replaces {@link @1.0::IOffloadControl::setDataLimit}, the framework will always
     * call setDataWarningAndLimit on 1.1 implementations, and setDataLimit on 1.0 implementations.
     * Thus, no interaction between the two APIs need to be addressed.
     *
     * The specified quota bytes MUST replace any previous quotas set by
     * {@code setDataWarningAndLimit} specified on the same interface. It may be interpreted as
     * "tell me when either <warningBytes> or <limitBytes> bytes have been transferred
     * (in either direction), and stop offload when <limitBytes> bytes have been transferred,
     * starting now and counting from zero on <upstream>."
     *
     * Once the {@code warningBytes} is reached, the callback registered in initOffload must be
     * called with {@code OFFLOAD_WARNING_REACHED} to indicate this event. Once the event fires
     * for this upstream, no further {@code OFFLOAD_WARNING_REACHED} event will be fired for this
     * upstream unless this method is called again with the same interface. Note that there is
     * no need to call initOffload again to resume offload if stopOffload was not called by the
     * client.
     *
     * Similarly, Once the {@code limitBytes} is reached, the callback registered in initOffload
     * must be called with {@code OFFLOAD_STOPPED_LIMIT_REACHED} to indicate this event. Once
     * the event fires for this upstream, no further {@code OFFLOAD_STOPPED_LIMIT_REACHED}
     * event will be fired for this upstream unless this method is called again with the same
     * interface. However, unlike {@code warningBytes}, when {@code limitBytes} is reached,
     * all offload must be stopped. If offload is desired again, the hardware management
     * process must be completely reprogrammed by calling setUpstreamParameters and
     * addDownstream again.
     *
     * Note that when one of the quota bytes is reached, the other one is still considered valid
     * unless this method is called again with the same interface.
     *
     * @param upstream Upstream interface name that quota must apply to.
     * @param warningBytes The quota of warning, defined as the number of bytes, starting from
     *                     zero and counting from now.
     * @param limitBytes The quota of limit, defined as the number of bytes, starting from zero
     *                   and counting from now.
     *
     * @return success true if quota is applied, false otherwise
     * @return errMsg a human readable string if error has occurred.
     */
    setDataWarningAndLimit(string upstream, uint64_t warningBytes, uint64_t limitBytes)
        generates (bool success, string errMsg);
};