| /* |
| * Copyright (C) 2018 The Android Open Source Project |
| * |
| * Licensed under the Apache License, Version 2.0 (the "License"); |
| * you may not use this file except in compliance with the License. |
| * You may obtain a copy of the License at |
| * |
| * http://www.apache.org/licenses/LICENSE-2.0 |
| * |
| * Unless required by applicable law or agreed to in writing, software |
| * distributed under the License is distributed on an "AS IS" BASIS, |
| * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. |
| * See the License for the specific language governing permissions and |
| * limitations under the License. |
| */ |
| package android.hardware.power.stats@1.0; |
| |
| interface IPowerStats { |
| |
| /** |
| * Rail information: |
| * Reports information related to the rails being monitored. |
| * |
| * @return rails Information about monitored rails. |
| * @return status SUCCESS on success or NOT_SUPPORTED if |
| * feature is not enabled or FILESYSTEM_ERROR on filesystem nodes |
| * access error. |
| */ |
| getRailInfo() |
| generates(vec<RailInfo> rails, Status status); |
| |
| /** |
| * Rail level energy measurements for low frequency clients: |
| * Reports accumulated energy since boot on each rail. |
| * |
| * @param railIndices Indices of rails for which data is required. |
| * To get data for all rails pass an empty vector. Rail name to |
| * index mapping can be queried from getRailInfo() API. |
| * @return data Energy values since boot for all requested rails. |
| * @return status SUCCESS on success or NOT_SUPPORTED if |
| * feature is not enabled or FILESYSTEM_ERROR on filesystem nodes |
| * access error. |
| */ |
| getEnergyData(vec<uint32_t> railIndices) |
| generates(vec<EnergyData> data, Status status); |
| |
| /** |
| * Stream rail level power measurements for high frequency clients: |
| * Streams accumulated energy since boot on each rail. This API is |
| * asynchronous. |
| * |
| * @param timeMs Time(in ms) for which energyData should be streamed |
| * @param samplingRate Frequency(in Hz) at which samples should be |
| * captured. If the requested sampling rate is not supported then |
| * SUCCESS is returned and numSamples are reported back according |
| * to the supported sampling rate. |
| * @return mqDesc Blocking Synchronous Fast Message Queue descriptor - One |
| * writer(power.stats HAL) and one reader are supported. Data is |
| * present in the following format in the queue: |
| * +-----------------------+ <-- |
| * | EnergyData for rail 1 | | |
| * +-----------------------+ | |
| * | EnergyData for rail 2 | | |
| * +-----------------------+ | |
| * | . | |-- 1st Sample |
| * | . | | |
| * | . | | |
| * +-----------------------+ | |
| * | EnergyData for rail n | | |
| * +-----------------------+ <-- |
| * | . | |
| * | . | |
| * | . | |
| * +-----------------------+ <-- |
| * | EnergyData for rail 1 | | |
| * +-----------------------+ | |
| * | EnergyData for rail 2 | | |
| * +-----------------------+ | |
| * | . | |-- kth Sample |
| * | . | | |
| * | . | | |
| * +-----------------------+ | |
| * | EnergyData for rail n | | |
| * +-----------------------+ <-- |
| * |
| * where, |
| * n = railsPerSample |
| * k = numSamples |
| * |
| * @return numSamples Number of samples which will be generated in timeMs. |
| * @return railsPerSample Number of rails measured per sample. |
| * @return status SUCCESS on success or FILESYSTEM_ERROR on filesystem |
| * nodes access or NOT_SUPPORTED if feature is not enabled or |
| * INSUFFICIENT_RESOURCES if there are not enough resources. |
| */ |
| streamEnergyData(uint32_t timeMs, uint32_t samplingRate) |
| generates(fmq_sync<EnergyData> mqDesc, uint32_t numSamples, |
| uint32_t railsPerSample, Status status); |
| |
| /** |
| * PowerEntity information: |
| * Reports information related to all supported PowerEntity(s) for which |
| * data is available. A PowerEntity is defined as a platform subsystem, |
| * peripheral, or power domain that impacts the total device power |
| * consumption. |
| * |
| * @return powerEntityInfos List of information on each PowerEntity |
| * @return status SUCCESS on success, NOT_SUPPORTED if feature is not |
| * enabled, FILESYSTEM_ERROR if there was an error accessing the |
| * filesystem. |
| */ |
| getPowerEntityInfo() |
| generates(vec<PowerEntityInfo> powerEntityInfos, Status status); |
| |
| /** |
| * PowerEntity state information: |
| * Reports the set of power states for which the specified |
| * PowerEntity(s) provide residency data. |
| * |
| * @param powerEntityIds collection of IDs of PowerEntity(s) for which |
| * state information is requested. PowerEntity name to ID mapping may |
| * be queried from getPowerEntityInfo(). To get state space |
| * information for all PowerEntity(s) pass an empty vector. |
| * |
| * @return powerEntityStateSpaces PowerEntity state space information for |
| * each specified PowerEntity that provides state space information. |
| * @return status SUCCESS on success, NOT_SUPPORTED if feature is not |
| * enabled, FILESYSTEM_ERROR if there was an error accessing the |
| * filesystem, INVALID_INPUT if any requested PowerEntity(s) do not |
| * provide state space information and there was not a filesystem error. |
| */ |
| getPowerEntityStateInfo(vec<uint32_t> powerEntityIds) |
| generates(vec<PowerEntityStateSpace> powerEntityStateSpaces, |
| Status status); |
| |
| /** |
| * PowerEntity residencies for low frequency clients: |
| * Reports accumulated residency data for each specified PowerEntity. |
| * Each PowerEntity may reside in one of multiple states. It may also |
| * transition to another state. Residency data is an accumulation of time |
| * that a specified PowerEntity resided in each of its possible states, |
| * the number of times that each state was entered, and a timestamp |
| * corresponding to the last time that state was entered. Data is |
| * accumulated starting from the last time the PowerEntity was reset. |
| * |
| * @param powerEntityId collection of IDs of PowerEntity(s) for which |
| * residency data is requested. PowerEntity name to ID mapping may |
| * be queried from getPowerEntityInfo(). To get state residency |
| * data for all PowerEntity(s) pass an empty vector. |
| * @return stateResidencyResults state residency data for each specified |
| * PowerEntity that provides state residency data. |
| * @return status SUCCESS on success, NOT_SUPPORTED if feature is not |
| * enabled, FILESYSTEM_ERROR if there was an error accessing the |
| * filesystem, INVALID_INPUT if any requested PowerEntity(s) do not |
| * provide state residency data and there was not a filesystem error. |
| */ |
| getPowerEntityStateResidencyData(vec<uint32_t> powerEntityIds) |
| generates(vec<PowerEntityStateResidencyResult> stateResidencyResults, |
| Status status); |
| }; |