| /* |
| * Copyright (C) 2010 The Android Open Source Project |
| * |
| * Licensed under the Apache License, Version 2.0 (the "License"); |
| * you may not use this file except in compliance with the License. |
| * You may obtain a copy of the License at |
| * |
| * http://www.apache.org/licenses/LICENSE-2.0 |
| * |
| * Unless required by applicable law or agreed to in writing, software |
| * distributed under the License is distributed on an "AS IS" BASIS, |
| * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. |
| * See the License for the specific language governing permissions and |
| * limitations under the License. |
| */ |
| |
| package android.net.wifi; |
| |
| import static android.net.wifi.WifiManager.WIFI_STATE_DISABLED; |
| import static android.net.wifi.WifiManager.WIFI_STATE_DISABLING; |
| import static android.net.wifi.WifiManager.WIFI_STATE_ENABLED; |
| import static android.net.wifi.WifiManager.WIFI_STATE_ENABLING; |
| import static android.net.wifi.WifiManager.WIFI_STATE_UNKNOWN; |
| |
| /** |
| * TODO: Add soft AP states as part of WIFI_STATE_XXX |
| * Retain WIFI_STATE_ENABLING that indicates driver is loading |
| * Add WIFI_STATE_AP_ENABLED to indicate soft AP has started |
| * and WIFI_STATE_FAILED for failure |
| * Deprecate WIFI_STATE_UNKNOWN |
| * |
| * Doing this will simplify the logic for sending broadcasts |
| */ |
| import static android.net.wifi.WifiManager.WIFI_AP_STATE_DISABLED; |
| import static android.net.wifi.WifiManager.WIFI_AP_STATE_DISABLING; |
| import static android.net.wifi.WifiManager.WIFI_AP_STATE_ENABLED; |
| import static android.net.wifi.WifiManager.WIFI_AP_STATE_ENABLING; |
| import static android.net.wifi.WifiManager.WIFI_AP_STATE_FAILED; |
| |
| import android.app.AlarmManager; |
| import android.app.PendingIntent; |
| import android.app.backup.IBackupManager; |
| import android.bluetooth.BluetoothAdapter; |
| import android.content.BroadcastReceiver; |
| import android.content.Context; |
| import android.content.Intent; |
| import android.content.IntentFilter; |
| import android.net.ConnectivityManager; |
| import android.net.DhcpInfo; |
| import android.net.DhcpInfoInternal; |
| import android.net.DhcpStateMachine; |
| import android.net.InterfaceConfiguration; |
| import android.net.LinkAddress; |
| import android.net.LinkProperties; |
| import android.net.NetworkInfo; |
| import android.net.NetworkInfo.DetailedState; |
| import android.net.NetworkUtils; |
| import android.net.wifi.WpsResult.Status; |
| import android.net.wifi.p2p.WifiP2pManager; |
| import android.net.wifi.p2p.WifiP2pService; |
| import android.net.wifi.StateChangeResult; |
| import android.os.Binder; |
| import android.os.IBinder; |
| import android.os.INetworkManagementService; |
| import android.os.Message; |
| import android.os.Messenger; |
| import android.os.PowerManager; |
| import android.os.Process; |
| import android.os.RemoteException; |
| import android.os.ServiceManager; |
| import android.os.SystemClock; |
| import android.os.SystemProperties; |
| import android.os.WorkSource; |
| import android.provider.Settings; |
| import android.util.EventLog; |
| import android.util.Log; |
| import android.util.LruCache; |
| import android.util.Slog; |
| |
| import com.android.internal.app.IBatteryStats; |
| import com.android.internal.util.AsyncChannel; |
| import com.android.internal.util.Protocol; |
| import com.android.internal.util.State; |
| import com.android.internal.util.StateMachine; |
| |
| import java.net.InetAddress; |
| import java.util.ArrayList; |
| import java.util.List; |
| import java.util.concurrent.atomic.AtomicInteger; |
| import java.util.concurrent.atomic.AtomicBoolean; |
| import java.util.regex.Pattern; |
| |
| /** |
| * Track the state of Wifi connectivity. All event handling is done here, |
| * and all changes in connectivity state are initiated here. |
| * |
| * Wi-Fi now supports three modes of operation: Client, Soft Ap and Direct |
| * In the current implementation, we do not support any concurrency and thus only |
| * one of Client, Soft Ap or Direct operation is supported at any time. |
| * |
| * The WifiStateMachine supports Soft Ap and Client operations while WifiP2pService |
| * handles Direct. WifiP2pService and WifiStateMachine co-ordinate to ensure only |
| * one exists at a certain time. |
| * |
| * @hide |
| */ |
| public class WifiStateMachine extends StateMachine { |
| |
| private static final String TAG = "WifiStateMachine"; |
| private static final String NETWORKTYPE = "WIFI"; |
| private static final boolean DBG = false; |
| |
| /* TODO: This is no more used with the hostapd code. Clean up */ |
| private static final String SOFTAP_IFACE = "wl0.1"; |
| |
| private WifiMonitor mWifiMonitor; |
| private INetworkManagementService mNwService; |
| private ConnectivityManager mCm; |
| |
| /* Scan results handling */ |
| private List<ScanResult> mScanResults; |
| private static final Pattern scanResultPattern = Pattern.compile("\t+"); |
| private static final int SCAN_RESULT_CACHE_SIZE = 80; |
| private final LruCache<String, ScanResult> mScanResultCache; |
| |
| private String mInterfaceName; |
| |
| private int mLastSignalLevel = -1; |
| private String mLastBssid; |
| private int mLastNetworkId; |
| private boolean mEnableRssiPolling = false; |
| private boolean mEnableBackgroundScan = false; |
| private int mRssiPollToken = 0; |
| private int mReconnectCount = 0; |
| private boolean mIsScanMode = false; |
| private boolean mScanResultIsPending = false; |
| |
| private boolean mBluetoothConnectionActive = false; |
| |
| /** |
| * Interval in milliseconds between polling for RSSI |
| * and linkspeed information |
| */ |
| private static final int POLL_RSSI_INTERVAL_MSECS = 3000; |
| |
| /** |
| * Delay between supplicant restarts upon failure to establish connection |
| */ |
| private static final int SUPPLICANT_RESTART_INTERVAL_MSECS = 5000; |
| |
| /** |
| * Number of times we attempt to restart supplicant |
| */ |
| private static final int SUPPLICANT_RESTART_TRIES = 5; |
| |
| private int mSupplicantRestartCount = 0; |
| |
| private LinkProperties mLinkProperties; |
| |
| // Wakelock held during wifi start/stop and driver load/unload |
| private PowerManager.WakeLock mWakeLock; |
| |
| private Context mContext; |
| |
| private DhcpInfoInternal mDhcpInfoInternal; |
| private WifiInfo mWifiInfo; |
| private NetworkInfo mNetworkInfo; |
| private SupplicantStateTracker mSupplicantStateTracker; |
| private WpsStateMachine mWpsStateMachine; |
| private DhcpStateMachine mDhcpStateMachine; |
| |
| private AlarmManager mAlarmManager; |
| private PendingIntent mScanIntent; |
| /* Tracks current frequency mode */ |
| private AtomicInteger mFrequencyBand = new AtomicInteger(WifiManager.WIFI_FREQUENCY_BAND_AUTO); |
| |
| /* Tracks if we are filtering Multicast v4 packets. Default is to filter. */ |
| private AtomicBoolean mFilteringMulticastV4Packets = new AtomicBoolean(true); |
| |
| // Channel for sending replies. |
| private AsyncChannel mReplyChannel = new AsyncChannel(); |
| |
| private WifiP2pManager mWifiP2pManager; |
| //Used to initiate a connection with WifiP2pService |
| private AsyncChannel mWifiP2pChannel = new AsyncChannel(); |
| |
| // Event log tags (must be in sync with event-log-tags) |
| private static final int EVENTLOG_WIFI_STATE_CHANGED = 50021; |
| private static final int EVENTLOG_WIFI_EVENT_HANDLED = 50022; |
| private static final int EVENTLOG_SUPPLICANT_STATE_CHANGED = 50023; |
| |
| /* The base for wifi message types */ |
| static final int BASE = Protocol.BASE_WIFI; |
| /* Load the driver */ |
| static final int CMD_LOAD_DRIVER = BASE + 1; |
| /* Unload the driver */ |
| static final int CMD_UNLOAD_DRIVER = BASE + 2; |
| /* Indicates driver load succeeded */ |
| static final int CMD_LOAD_DRIVER_SUCCESS = BASE + 3; |
| /* Indicates driver load failed */ |
| static final int CMD_LOAD_DRIVER_FAILURE = BASE + 4; |
| /* Indicates driver unload succeeded */ |
| static final int CMD_UNLOAD_DRIVER_SUCCESS = BASE + 5; |
| /* Indicates driver unload failed */ |
| static final int CMD_UNLOAD_DRIVER_FAILURE = BASE + 6; |
| |
| /* Start the supplicant */ |
| static final int CMD_START_SUPPLICANT = BASE + 11; |
| /* Stop the supplicant */ |
| static final int CMD_STOP_SUPPLICANT = BASE + 12; |
| /* Start the driver */ |
| static final int CMD_START_DRIVER = BASE + 13; |
| /* Start the driver */ |
| static final int CMD_STOP_DRIVER = BASE + 14; |
| /* Indicates Static IP succeded */ |
| static final int CMD_STATIC_IP_SUCCESS = BASE + 15; |
| /* Indicates Static IP failed */ |
| static final int CMD_STATIC_IP_FAILURE = BASE + 16; |
| |
| /* Start the soft access point */ |
| static final int CMD_START_AP = BASE + 21; |
| /* Indicates soft ap start succeded */ |
| static final int CMD_START_AP_SUCCESS = BASE + 22; |
| /* Indicates soft ap start failed */ |
| static final int CMD_START_AP_FAILURE = BASE + 23; |
| /* Stop the soft access point */ |
| static final int CMD_STOP_AP = BASE + 24; |
| /* Set the soft access point configuration */ |
| static final int CMD_SET_AP_CONFIG = BASE + 25; |
| /* Get the soft access point configuration */ |
| static final int CMD_GET_AP_CONFIG = BASE + 26; |
| /* Set configuration on tether interface */ |
| static final int CMD_TETHER_INTERFACE = BASE + 27; |
| |
| static final int CMD_BLUETOOTH_ADAPTER_STATE_CHANGE = BASE + 28; |
| |
| /* Supplicant commands */ |
| /* Is supplicant alive ? */ |
| static final int CMD_PING_SUPPLICANT = BASE + 51; |
| /* Add/update a network configuration */ |
| static final int CMD_ADD_OR_UPDATE_NETWORK = BASE + 52; |
| /* Delete a network */ |
| static final int CMD_REMOVE_NETWORK = BASE + 53; |
| /* Enable a network. The device will attempt a connection to the given network. */ |
| static final int CMD_ENABLE_NETWORK = BASE + 54; |
| /* Enable all networks */ |
| static final int CMD_ENABLE_ALL_NETWORKS = BASE + 55; |
| /* Disable a network. The device does not attempt a connection to the given network. */ |
| static final int CMD_DISABLE_NETWORK = BASE + 56; |
| /* Blacklist network. De-prioritizes the given BSSID for connection. */ |
| static final int CMD_BLACKLIST_NETWORK = BASE + 57; |
| /* Clear the blacklist network list */ |
| static final int CMD_CLEAR_BLACKLIST = BASE + 58; |
| /* Save configuration */ |
| static final int CMD_SAVE_CONFIG = BASE + 59; |
| |
| /* Supplicant commands after driver start*/ |
| /* Initiate a scan */ |
| static final int CMD_START_SCAN = BASE + 71; |
| /* Set scan mode. CONNECT_MODE or SCAN_ONLY_MODE */ |
| static final int CMD_SET_SCAN_MODE = BASE + 72; |
| /* Set scan type. SCAN_ACTIVE or SCAN_PASSIVE */ |
| static final int CMD_SET_SCAN_TYPE = BASE + 73; |
| /* Disconnect from a network */ |
| static final int CMD_DISCONNECT = BASE + 74; |
| /* Reconnect to a network */ |
| static final int CMD_RECONNECT = BASE + 75; |
| /* Reassociate to a network */ |
| static final int CMD_REASSOCIATE = BASE + 76; |
| /* Controls power mode and suspend mode optimizations |
| * |
| * When high perf mode is enabled, power mode is set to |
| * POWER_MODE_ACTIVE and suspend mode optimizations are disabled |
| * |
| * When high perf mode is disabled, power mode is set to |
| * POWER_MODE_AUTO and suspend mode optimizations are enabled |
| * |
| * Suspend mode optimizations include: |
| * - packet filtering |
| * - turn off roaming |
| * - DTIM wake up settings |
| */ |
| static final int CMD_SET_HIGH_PERF_MODE = BASE + 77; |
| /* Set the country code */ |
| static final int CMD_SET_COUNTRY_CODE = BASE + 80; |
| /* Request connectivity manager wake lock before driver stop */ |
| static final int CMD_REQUEST_CM_WAKELOCK = BASE + 81; |
| /* Enables RSSI poll */ |
| static final int CMD_ENABLE_RSSI_POLL = BASE + 82; |
| /* RSSI poll */ |
| static final int CMD_RSSI_POLL = BASE + 83; |
| /* Set up packet filtering */ |
| static final int CMD_START_PACKET_FILTERING = BASE + 84; |
| /* Clear packet filter */ |
| static final int CMD_STOP_PACKET_FILTERING = BASE + 85; |
| |
| /* arg1 values to CMD_STOP_PACKET_FILTERING and CMD_START_PACKET_FILTERING */ |
| static final int MULTICAST_V6 = 1; |
| static final int MULTICAST_V4 = 0; |
| |
| /* Connect to a specified network (network id |
| * or WifiConfiguration) This involves increasing |
| * the priority of the network, enabling the network |
| * (while disabling others) and issuing a reconnect. |
| * Note that CMD_RECONNECT just does a reconnect to |
| * an existing network. All the networks get enabled |
| * upon a successful connection or a failure. |
| */ |
| static final int CMD_CONNECT_NETWORK = BASE + 86; |
| /* Save the specified network. This involves adding |
| * an enabled network (if new) and updating the |
| * config and issuing a save on supplicant config. |
| */ |
| static final int CMD_SAVE_NETWORK = BASE + 87; |
| /* Delete the specified network. This involves |
| * removing the network and issuing a save on |
| * supplicant config. |
| */ |
| static final int CMD_FORGET_NETWORK = BASE + 88; |
| /* Start Wi-Fi protected setup */ |
| static final int CMD_START_WPS = BASE + 89; |
| /* Set the frequency band */ |
| static final int CMD_SET_FREQUENCY_BAND = BASE + 90; |
| /* Enable background scan for configured networks */ |
| static final int CMD_ENABLE_BACKGROUND_SCAN = BASE + 91; |
| |
| /* Commands from/to the SupplicantStateTracker */ |
| /* Reset the supplicant state tracker */ |
| static final int CMD_RESET_SUPPLICANT_STATE = BASE + 111; |
| |
| /* Commands/events reported by WpsStateMachine */ |
| /* Indicates the completion of WPS activity */ |
| static final int WPS_COMPLETED_EVENT = BASE + 121; |
| /* Reset the WPS state machine */ |
| static final int CMD_RESET_WPS_STATE = BASE + 122; |
| |
| /* Interaction with WifiP2pService */ |
| public static final int WIFI_ENABLE_PENDING = BASE + 131; |
| public static final int P2P_ENABLE_PROCEED = BASE + 132; |
| |
| private static final int CONNECT_MODE = 1; |
| private static final int SCAN_ONLY_MODE = 2; |
| |
| private static final int SCAN_ACTIVE = 1; |
| private static final int SCAN_PASSIVE = 2; |
| |
| private static final int SUCCESS = 1; |
| private static final int FAILURE = -1; |
| |
| /** |
| * The maximum number of times we will retry a connection to an access point |
| * for which we have failed in acquiring an IP address from DHCP. A value of |
| * N means that we will make N+1 connection attempts in all. |
| * <p> |
| * See {@link Settings.Secure#WIFI_MAX_DHCP_RETRY_COUNT}. This is the default |
| * value if a Settings value is not present. |
| */ |
| private static final int DEFAULT_MAX_DHCP_RETRIES = 9; |
| |
| static final int POWER_MODE_ACTIVE = 1; |
| static final int POWER_MODE_AUTO = 0; |
| |
| /* Tracks the power mode for restoration after a DHCP request/renewal goes through */ |
| private int mPowerMode = POWER_MODE_AUTO; |
| |
| /** |
| * Default framework scan interval in milliseconds. This is used in the scenario in which |
| * wifi chipset does not support background scanning to set up a |
| * periodic wake up scan so that the device can connect to a new access |
| * point on the move. {@link Settings.Secure#WIFI_FRAMEWORK_SCAN_INTERVAL_MS} can |
| * override this. |
| */ |
| private final int mDefaultFrameworkScanIntervalMs; |
| |
| /** |
| * Default supplicant scan interval in milliseconds. |
| * {@link Settings.Secure#WIFI_SUPPLICANT_SCAN_INTERVAL_MS} can override this. |
| */ |
| private final int mDefaultSupplicantScanIntervalMs; |
| |
| |
| private static final int MIN_RSSI = -200; |
| private static final int MAX_RSSI = 256; |
| |
| /* Default parent state */ |
| private State mDefaultState = new DefaultState(); |
| /* Temporary initial state */ |
| private State mInitialState = new InitialState(); |
| /* Unloading the driver */ |
| private State mDriverUnloadingState = new DriverUnloadingState(); |
| /* Loading the driver */ |
| private State mDriverUnloadedState = new DriverUnloadedState(); |
| /* Driver load/unload failed */ |
| private State mDriverFailedState = new DriverFailedState(); |
| /* Driver loading */ |
| private State mDriverLoadingState = new DriverLoadingState(); |
| /* Driver loaded */ |
| private State mDriverLoadedState = new DriverLoadedState(); |
| /* Driver loaded, waiting for supplicant to start */ |
| private State mSupplicantStartingState = new SupplicantStartingState(); |
| /* Driver loaded and supplicant ready */ |
| private State mSupplicantStartedState = new SupplicantStartedState(); |
| /* Waiting for supplicant to stop and monitor to exit */ |
| private State mSupplicantStoppingState = new SupplicantStoppingState(); |
| /* Driver start issued, waiting for completed event */ |
| private State mDriverStartingState = new DriverStartingState(); |
| /* Driver started */ |
| private State mDriverStartedState = new DriverStartedState(); |
| /* Driver stopping */ |
| private State mDriverStoppingState = new DriverStoppingState(); |
| /* Driver stopped */ |
| private State mDriverStoppedState = new DriverStoppedState(); |
| /* Scan for networks, no connection will be established */ |
| private State mScanModeState = new ScanModeState(); |
| /* Connecting to an access point */ |
| private State mConnectModeState = new ConnectModeState(); |
| /* Fetching IP after network connection (assoc+auth complete) */ |
| private State mConnectingState = new ConnectingState(); |
| /* Connected with IP addr */ |
| private State mConnectedState = new ConnectedState(); |
| /* disconnect issued, waiting for network disconnect confirmation */ |
| private State mDisconnectingState = new DisconnectingState(); |
| /* Network is not connected, supplicant assoc+auth is not complete */ |
| private State mDisconnectedState = new DisconnectedState(); |
| /* Waiting for WPS to be completed*/ |
| private State mWaitForWpsCompletionState = new WaitForWpsCompletionState(); |
| |
| /* Soft ap is starting up */ |
| private State mSoftApStartingState = new SoftApStartingState(); |
| /* Soft ap is running */ |
| private State mSoftApStartedState = new SoftApStartedState(); |
| /* Soft ap is running and we are tethered through connectivity service */ |
| private State mTetheredState = new TetheredState(); |
| |
| /* Wait till p2p is disabled */ |
| private State mWaitForP2pDisableState = new WaitForP2pDisableState(); |
| |
| |
| /** |
| * One of {@link WifiManager#WIFI_STATE_DISABLED}, |
| * {@link WifiManager#WIFI_STATE_DISABLING}, |
| * {@link WifiManager#WIFI_STATE_ENABLED}, |
| * {@link WifiManager#WIFI_STATE_ENABLING}, |
| * {@link WifiManager#WIFI_STATE_UNKNOWN} |
| * |
| */ |
| private final AtomicInteger mWifiState = new AtomicInteger(WIFI_STATE_DISABLED); |
| |
| /** |
| * One of {@link WifiManager#WIFI_AP_STATE_DISABLED}, |
| * {@link WifiManager#WIFI_AP_STATE_DISABLING}, |
| * {@link WifiManager#WIFI_AP_STATE_ENABLED}, |
| * {@link WifiManager#WIFI_AP_STATE_ENABLING}, |
| * {@link WifiManager#WIFI_AP_STATE_FAILED} |
| * |
| */ |
| private final AtomicInteger mWifiApState = new AtomicInteger(WIFI_AP_STATE_DISABLED); |
| |
| private final AtomicInteger mLastEnableUid = new AtomicInteger(Process.myUid()); |
| private final AtomicInteger mLastApEnableUid = new AtomicInteger(Process.myUid()); |
| |
| private static final int SCAN_REQUEST = 0; |
| private static final String ACTION_START_SCAN = |
| "com.android.server.WifiManager.action.START_SCAN"; |
| |
| /** |
| * Keep track of whether WIFI is running. |
| */ |
| private boolean mIsRunning = false; |
| |
| /** |
| * Keep track of whether we last told the battery stats we had started. |
| */ |
| private boolean mReportedRunning = false; |
| |
| /** |
| * Most recently set source of starting WIFI. |
| */ |
| private final WorkSource mRunningWifiUids = new WorkSource(); |
| |
| /** |
| * The last reported UIDs that were responsible for starting WIFI. |
| */ |
| private final WorkSource mLastRunningWifiUids = new WorkSource(); |
| |
| private final IBatteryStats mBatteryStats; |
| private boolean mNextWifiActionExplicit = false; |
| private int mLastExplicitNetworkId; |
| private long mLastNetworkChoiceTime; |
| private static final long EXPLICIT_CONNECT_ALLOWED_DELAY_MS = 2 * 60 * 1000; |
| |
| |
| public WifiStateMachine(Context context, String wlanInterface) { |
| super(TAG); |
| |
| mContext = context; |
| mInterfaceName = wlanInterface; |
| |
| mNetworkInfo = new NetworkInfo(ConnectivityManager.TYPE_WIFI, 0, NETWORKTYPE, ""); |
| mBatteryStats = IBatteryStats.Stub.asInterface(ServiceManager.getService("batteryinfo")); |
| |
| IBinder b = ServiceManager.getService(Context.NETWORKMANAGEMENT_SERVICE); |
| mNwService = INetworkManagementService.Stub.asInterface(b); |
| |
| mWifiMonitor = new WifiMonitor(this); |
| mDhcpInfoInternal = new DhcpInfoInternal(); |
| mWifiInfo = new WifiInfo(); |
| mSupplicantStateTracker = new SupplicantStateTracker(context, this, getHandler()); |
| mWpsStateMachine = new WpsStateMachine(context, this, getHandler()); |
| mLinkProperties = new LinkProperties(); |
| |
| mNetworkInfo.setIsAvailable(false); |
| mLinkProperties.clear(); |
| mLastBssid = null; |
| mLastNetworkId = WifiConfiguration.INVALID_NETWORK_ID; |
| mLastSignalLevel = -1; |
| |
| mAlarmManager = (AlarmManager)mContext.getSystemService(Context.ALARM_SERVICE); |
| Intent scanIntent = new Intent(ACTION_START_SCAN, null); |
| mScanIntent = PendingIntent.getBroadcast(mContext, SCAN_REQUEST, scanIntent, 0); |
| |
| mDefaultFrameworkScanIntervalMs = mContext.getResources().getInteger( |
| com.android.internal.R.integer.config_wifi_framework_scan_interval); |
| |
| mDefaultSupplicantScanIntervalMs = mContext.getResources().getInteger( |
| com.android.internal.R.integer.config_wifi_supplicant_scan_interval); |
| |
| mContext.registerReceiver( |
| new BroadcastReceiver() { |
| @Override |
| public void onReceive(Context context, Intent intent) { |
| ArrayList<String> available = intent.getStringArrayListExtra( |
| ConnectivityManager.EXTRA_AVAILABLE_TETHER); |
| sendMessage(CMD_TETHER_INTERFACE, available); |
| } |
| },new IntentFilter(ConnectivityManager.ACTION_TETHER_STATE_CHANGED)); |
| |
| mContext.registerReceiver( |
| new BroadcastReceiver() { |
| @Override |
| public void onReceive(Context context, Intent intent) { |
| startScan(false); |
| } |
| }, |
| new IntentFilter(ACTION_START_SCAN)); |
| |
| mScanResultCache = new LruCache<String, ScanResult>(SCAN_RESULT_CACHE_SIZE); |
| |
| PowerManager powerManager = (PowerManager)mContext.getSystemService(Context.POWER_SERVICE); |
| mWakeLock = powerManager.newWakeLock(PowerManager.PARTIAL_WAKE_LOCK, TAG); |
| |
| addState(mDefaultState); |
| addState(mInitialState, mDefaultState); |
| addState(mDriverUnloadingState, mDefaultState); |
| addState(mDriverUnloadedState, mDefaultState); |
| addState(mDriverFailedState, mDriverUnloadedState); |
| addState(mDriverLoadingState, mDefaultState); |
| addState(mDriverLoadedState, mDefaultState); |
| addState(mSupplicantStartingState, mDefaultState); |
| addState(mSupplicantStartedState, mDefaultState); |
| addState(mDriverStartingState, mSupplicantStartedState); |
| addState(mDriverStartedState, mSupplicantStartedState); |
| addState(mScanModeState, mDriverStartedState); |
| addState(mConnectModeState, mDriverStartedState); |
| addState(mConnectingState, mConnectModeState); |
| addState(mConnectedState, mConnectModeState); |
| addState(mDisconnectingState, mConnectModeState); |
| addState(mDisconnectedState, mConnectModeState); |
| addState(mWaitForWpsCompletionState, mConnectModeState); |
| addState(mDriverStoppingState, mSupplicantStartedState); |
| addState(mDriverStoppedState, mSupplicantStartedState); |
| addState(mSupplicantStoppingState, mDefaultState); |
| addState(mSoftApStartingState, mDefaultState); |
| addState(mSoftApStartedState, mDefaultState); |
| addState(mTetheredState, mSoftApStartedState); |
| addState(mWaitForP2pDisableState, mDefaultState); |
| |
| setInitialState(mInitialState); |
| |
| if (DBG) setDbg(true); |
| |
| //start the state machine |
| start(); |
| } |
| |
| /********************************************************* |
| * Methods exposed for public use |
| ********************************************************/ |
| |
| /** |
| * TODO: doc |
| */ |
| public boolean syncPingSupplicant(AsyncChannel channel) { |
| Message resultMsg = channel.sendMessageSynchronously(CMD_PING_SUPPLICANT); |
| boolean result = (resultMsg.arg1 != FAILURE); |
| resultMsg.recycle(); |
| return result; |
| } |
| |
| /** |
| * TODO: doc |
| */ |
| public void startScan(boolean forceActive) { |
| sendMessage(obtainMessage(CMD_START_SCAN, forceActive ? |
| SCAN_ACTIVE : SCAN_PASSIVE, 0)); |
| } |
| |
| /** |
| * TODO: doc |
| */ |
| public void setWifiEnabled(boolean enable) { |
| mLastEnableUid.set(Binder.getCallingUid()); |
| if (enable) { |
| /* Argument is the state that is entered prior to load */ |
| sendMessage(obtainMessage(CMD_LOAD_DRIVER, WIFI_STATE_ENABLING, 0)); |
| sendMessage(CMD_START_SUPPLICANT); |
| } else { |
| sendMessage(CMD_STOP_SUPPLICANT); |
| /* Argument is the state that is entered upon success */ |
| sendMessage(obtainMessage(CMD_UNLOAD_DRIVER, WIFI_STATE_DISABLED, 0)); |
| } |
| } |
| |
| /** |
| * TODO: doc |
| */ |
| public void setWifiApEnabled(WifiConfiguration wifiConfig, boolean enable) { |
| mLastApEnableUid.set(Binder.getCallingUid()); |
| if (enable) { |
| /* Argument is the state that is entered prior to load */ |
| sendMessage(obtainMessage(CMD_LOAD_DRIVER, WIFI_AP_STATE_ENABLING, 0)); |
| sendMessage(obtainMessage(CMD_START_AP, wifiConfig)); |
| } else { |
| sendMessage(CMD_STOP_AP); |
| /* Argument is the state that is entered upon success */ |
| sendMessage(obtainMessage(CMD_UNLOAD_DRIVER, WIFI_AP_STATE_DISABLED, 0)); |
| } |
| } |
| |
| public void setWifiApConfiguration(WifiConfiguration config) { |
| sendMessage(obtainMessage(CMD_SET_AP_CONFIG, config)); |
| } |
| |
| public WifiConfiguration syncGetWifiApConfiguration(AsyncChannel channel) { |
| Message resultMsg = channel.sendMessageSynchronously(CMD_GET_AP_CONFIG); |
| WifiConfiguration ret = (WifiConfiguration) resultMsg.obj; |
| resultMsg.recycle(); |
| return ret; |
| } |
| |
| /** |
| * TODO: doc |
| */ |
| public int syncGetWifiState() { |
| return mWifiState.get(); |
| } |
| |
| /** |
| * TODO: doc |
| */ |
| public String syncGetWifiStateByName() { |
| switch (mWifiState.get()) { |
| case WIFI_STATE_DISABLING: |
| return "disabling"; |
| case WIFI_STATE_DISABLED: |
| return "disabled"; |
| case WIFI_STATE_ENABLING: |
| return "enabling"; |
| case WIFI_STATE_ENABLED: |
| return "enabled"; |
| case WIFI_STATE_UNKNOWN: |
| return "unknown state"; |
| default: |
| return "[invalid state]"; |
| } |
| } |
| |
| /** |
| * TODO: doc |
| */ |
| public int syncGetWifiApState() { |
| return mWifiApState.get(); |
| } |
| |
| /** |
| * TODO: doc |
| */ |
| public String syncGetWifiApStateByName() { |
| switch (mWifiApState.get()) { |
| case WIFI_AP_STATE_DISABLING: |
| return "disabling"; |
| case WIFI_AP_STATE_DISABLED: |
| return "disabled"; |
| case WIFI_AP_STATE_ENABLING: |
| return "enabling"; |
| case WIFI_AP_STATE_ENABLED: |
| return "enabled"; |
| case WIFI_AP_STATE_FAILED: |
| return "failed"; |
| default: |
| return "[invalid state]"; |
| } |
| } |
| |
| /** |
| * Get status information for the current connection, if any. |
| * @return a {@link WifiInfo} object containing information about the current connection |
| * |
| */ |
| public WifiInfo syncRequestConnectionInfo() { |
| return mWifiInfo; |
| } |
| |
| public DhcpInfo syncGetDhcpInfo() { |
| synchronized (mDhcpInfoInternal) { |
| return mDhcpInfoInternal.makeDhcpInfo(); |
| } |
| } |
| |
| /** |
| * TODO: doc |
| */ |
| public void setDriverStart(boolean enable) { |
| if (enable) { |
| sendMessage(CMD_START_DRIVER); |
| } else { |
| sendMessage(CMD_STOP_DRIVER); |
| } |
| } |
| |
| /** |
| * TODO: doc |
| */ |
| public void setScanOnlyMode(boolean enable) { |
| if (enable) { |
| sendMessage(obtainMessage(CMD_SET_SCAN_MODE, SCAN_ONLY_MODE, 0)); |
| } else { |
| sendMessage(obtainMessage(CMD_SET_SCAN_MODE, CONNECT_MODE, 0)); |
| } |
| } |
| |
| /** |
| * TODO: doc |
| */ |
| public void setScanType(boolean active) { |
| if (active) { |
| sendMessage(obtainMessage(CMD_SET_SCAN_TYPE, SCAN_ACTIVE, 0)); |
| } else { |
| sendMessage(obtainMessage(CMD_SET_SCAN_TYPE, SCAN_PASSIVE, 0)); |
| } |
| } |
| |
| /** |
| * TODO: doc |
| */ |
| public List<ScanResult> syncGetScanResultsList() { |
| return mScanResults; |
| } |
| |
| /** |
| * Disconnect from Access Point |
| */ |
| public void disconnectCommand() { |
| sendMessage(CMD_DISCONNECT); |
| } |
| |
| /** |
| * Initiate a reconnection to AP |
| */ |
| public void reconnectCommand() { |
| sendMessage(CMD_RECONNECT); |
| } |
| |
| /** |
| * Initiate a re-association to AP |
| */ |
| public void reassociateCommand() { |
| sendMessage(CMD_REASSOCIATE); |
| } |
| |
| /** |
| * Add a network synchronously |
| * |
| * @return network id of the new network |
| */ |
| public int syncAddOrUpdateNetwork(AsyncChannel channel, WifiConfiguration config) { |
| Message resultMsg = channel.sendMessageSynchronously(CMD_ADD_OR_UPDATE_NETWORK, config); |
| int result = resultMsg.arg1; |
| resultMsg.recycle(); |
| return result; |
| } |
| |
| public List<WifiConfiguration> syncGetConfiguredNetworks() { |
| return WifiConfigStore.getConfiguredNetworks(); |
| } |
| |
| /** |
| * Delete a network |
| * |
| * @param networkId id of the network to be removed |
| */ |
| public boolean syncRemoveNetwork(AsyncChannel channel, int networkId) { |
| Message resultMsg = channel.sendMessageSynchronously(CMD_REMOVE_NETWORK, networkId); |
| boolean result = (resultMsg.arg1 != FAILURE); |
| resultMsg.recycle(); |
| return result; |
| } |
| |
| /** |
| * Enable a network |
| * |
| * @param netId network id of the network |
| * @param disableOthers true, if all other networks have to be disabled |
| * @return {@code true} if the operation succeeds, {@code false} otherwise |
| */ |
| public boolean syncEnableNetwork(AsyncChannel channel, int netId, boolean disableOthers) { |
| Message resultMsg = channel.sendMessageSynchronously(CMD_ENABLE_NETWORK, netId, |
| disableOthers ? 1 : 0); |
| boolean result = (resultMsg.arg1 != FAILURE); |
| resultMsg.recycle(); |
| return result; |
| } |
| |
| /** |
| * Disable a network |
| * |
| * @param netId network id of the network |
| * @return {@code true} if the operation succeeds, {@code false} otherwise |
| */ |
| public boolean syncDisableNetwork(AsyncChannel channel, int netId) { |
| Message resultMsg = channel.sendMessageSynchronously(CMD_DISABLE_NETWORK, netId, |
| WifiConfiguration.DISABLED_UNKNOWN_REASON); |
| boolean result = (resultMsg.arg1 != FAILURE); |
| resultMsg.recycle(); |
| return result; |
| } |
| |
| /** |
| * Blacklist a BSSID. This will avoid the AP if there are |
| * alternate APs to connect |
| * |
| * @param bssid BSSID of the network |
| */ |
| public void addToBlacklist(String bssid) { |
| sendMessage(obtainMessage(CMD_BLACKLIST_NETWORK, bssid)); |
| } |
| |
| /** |
| * Clear the blacklist list |
| * |
| */ |
| public void clearBlacklist() { |
| sendMessage(obtainMessage(CMD_CLEAR_BLACKLIST)); |
| } |
| |
| public void connectNetwork(int netId) { |
| sendMessage(obtainMessage(CMD_CONNECT_NETWORK, netId, 0)); |
| } |
| |
| public void connectNetwork(WifiConfiguration wifiConfig) { |
| /* arg1 is used to indicate netId, force a netId value of |
| * WifiConfiguration.INVALID_NETWORK_ID when we are passing |
| * a configuration since the default value of 0 is a valid netId |
| */ |
| sendMessage(obtainMessage(CMD_CONNECT_NETWORK, WifiConfiguration.INVALID_NETWORK_ID, |
| 0, wifiConfig)); |
| } |
| |
| public void saveNetwork(WifiConfiguration wifiConfig) { |
| sendMessage(obtainMessage(CMD_SAVE_NETWORK, wifiConfig)); |
| } |
| |
| public void forgetNetwork(int netId) { |
| sendMessage(obtainMessage(CMD_FORGET_NETWORK, netId, 0)); |
| } |
| |
| public void disableNetwork(Messenger replyTo, int netId, int reason) { |
| Message message = obtainMessage(CMD_DISABLE_NETWORK, netId, reason); |
| message.replyTo = replyTo; |
| sendMessage(message); |
| } |
| |
| public void startWps(Messenger replyTo, WpsInfo config) { |
| Message msg = obtainMessage(CMD_START_WPS, config); |
| msg.replyTo = replyTo; |
| sendMessage(msg); |
| } |
| |
| public void enableRssiPolling(boolean enabled) { |
| sendMessage(obtainMessage(CMD_ENABLE_RSSI_POLL, enabled ? 1 : 0, 0)); |
| } |
| |
| public void enableBackgroundScanCommand(boolean enabled) { |
| sendMessage(obtainMessage(CMD_ENABLE_BACKGROUND_SCAN, enabled ? 1 : 0, 0)); |
| } |
| |
| public void enableAllNetworks() { |
| sendMessage(CMD_ENABLE_ALL_NETWORKS); |
| } |
| |
| /** |
| * Start filtering Multicast v4 packets |
| */ |
| public void startFilteringMulticastV4Packets() { |
| mFilteringMulticastV4Packets.set(true); |
| sendMessage(obtainMessage(CMD_START_PACKET_FILTERING, MULTICAST_V4, 0)); |
| } |
| |
| /** |
| * Stop filtering Multicast v4 packets |
| */ |
| public void stopFilteringMulticastV4Packets() { |
| mFilteringMulticastV4Packets.set(false); |
| sendMessage(obtainMessage(CMD_STOP_PACKET_FILTERING, MULTICAST_V4, 0)); |
| } |
| |
| /** |
| * Start filtering Multicast v4 packets |
| */ |
| public void startFilteringMulticastV6Packets() { |
| sendMessage(obtainMessage(CMD_START_PACKET_FILTERING, MULTICAST_V6, 0)); |
| } |
| |
| /** |
| * Stop filtering Multicast v4 packets |
| */ |
| public void stopFilteringMulticastV6Packets() { |
| sendMessage(obtainMessage(CMD_STOP_PACKET_FILTERING, MULTICAST_V6, 0)); |
| } |
| |
| /** |
| * Set high performance mode of operation. |
| * Enabling would set active power mode and disable suspend optimizations; |
| * disabling would set auto power mode and enable suspend optimizations |
| * @param enable true if enable, false otherwise |
| */ |
| public void setHighPerfModeEnabled(boolean enable) { |
| sendMessage(obtainMessage(CMD_SET_HIGH_PERF_MODE, enable ? 1 : 0, 0)); |
| } |
| |
| /** |
| * Set the country code |
| * @param countryCode following ISO 3166 format |
| * @param persist {@code true} if the setting should be remembered. |
| */ |
| public void setCountryCode(String countryCode, boolean persist) { |
| if (persist) { |
| Settings.Secure.putString(mContext.getContentResolver(), |
| Settings.Secure.WIFI_COUNTRY_CODE, |
| countryCode); |
| } |
| sendMessage(obtainMessage(CMD_SET_COUNTRY_CODE, countryCode)); |
| } |
| |
| /** |
| * Set the operational frequency band |
| * @param band |
| * @param persist {@code true} if the setting should be remembered. |
| */ |
| public void setFrequencyBand(int band, boolean persist) { |
| if (persist) { |
| Settings.Secure.putInt(mContext.getContentResolver(), |
| Settings.Secure.WIFI_FREQUENCY_BAND, |
| band); |
| } |
| sendMessage(obtainMessage(CMD_SET_FREQUENCY_BAND, band, 0)); |
| } |
| |
| /** |
| * Returns the operational frequency band |
| */ |
| public int getFrequencyBand() { |
| return mFrequencyBand.get(); |
| } |
| |
| /** |
| * Returns the wifi configuration file |
| */ |
| public String getConfigFile() { |
| return WifiConfigStore.getConfigFile(); |
| } |
| |
| /** |
| * Send a message indicating bluetooth adapter connection state changed |
| */ |
| public void sendBluetoothAdapterStateChange(int state) { |
| sendMessage(obtainMessage(CMD_BLUETOOTH_ADAPTER_STATE_CHANGE, state, 0)); |
| } |
| |
| /** |
| * Save configuration on supplicant |
| * |
| * @return {@code true} if the operation succeeds, {@code false} otherwise |
| * |
| * TODO: deprecate this |
| */ |
| public boolean syncSaveConfig(AsyncChannel channel) { |
| Message resultMsg = channel.sendMessageSynchronously(CMD_SAVE_CONFIG); |
| boolean result = (resultMsg.arg1 != FAILURE); |
| resultMsg.recycle(); |
| return result; |
| } |
| |
| /** |
| * Request a wakelock with connectivity service to |
| * keep the device awake until we hand-off from wifi |
| * to an alternate network |
| */ |
| public void requestCmWakeLock() { |
| sendMessage(CMD_REQUEST_CM_WAKELOCK); |
| } |
| |
| public void updateBatteryWorkSource(WorkSource newSource) { |
| synchronized (mRunningWifiUids) { |
| try { |
| if (newSource != null) { |
| mRunningWifiUids.set(newSource); |
| } |
| if (mIsRunning) { |
| if (mReportedRunning) { |
| // If the work source has changed since last time, need |
| // to remove old work from battery stats. |
| if (mLastRunningWifiUids.diff(mRunningWifiUids)) { |
| mBatteryStats.noteWifiRunningChanged(mLastRunningWifiUids, |
| mRunningWifiUids); |
| mLastRunningWifiUids.set(mRunningWifiUids); |
| } |
| } else { |
| // Now being started, report it. |
| mBatteryStats.noteWifiRunning(mRunningWifiUids); |
| mLastRunningWifiUids.set(mRunningWifiUids); |
| mReportedRunning = true; |
| } |
| } else { |
| if (mReportedRunning) { |
| // Last reported we were running, time to stop. |
| mBatteryStats.noteWifiStopped(mLastRunningWifiUids); |
| mLastRunningWifiUids.clear(); |
| mReportedRunning = false; |
| } |
| } |
| mWakeLock.setWorkSource(newSource); |
| } catch (RemoteException ignore) { |
| } |
| } |
| } |
| |
| @Override |
| public String toString() { |
| StringBuffer sb = new StringBuffer(); |
| String LS = System.getProperty("line.separator"); |
| sb.append("current HSM state: ").append(getCurrentState().getName()).append(LS); |
| sb.append("mLinkProperties ").append(mLinkProperties).append(LS); |
| sb.append("mWifiInfo ").append(mWifiInfo).append(LS); |
| sb.append("mDhcpInfoInternal ").append(mDhcpInfoInternal).append(LS); |
| sb.append("mNetworkInfo ").append(mNetworkInfo).append(LS); |
| sb.append("mLastSignalLevel ").append(mLastSignalLevel).append(LS); |
| sb.append("mLastBssid ").append(mLastBssid).append(LS); |
| sb.append("mLastNetworkId ").append(mLastNetworkId).append(LS); |
| sb.append("mReconnectCount ").append(mReconnectCount).append(LS); |
| sb.append("mIsScanMode ").append(mIsScanMode).append(LS); |
| sb.append("Supplicant status").append(LS) |
| .append(WifiNative.statusCommand()).append(LS).append(LS); |
| |
| sb.append(WifiConfigStore.dump()); |
| return sb.toString(); |
| } |
| |
| /********************************************************* |
| * Internal private functions |
| ********************************************************/ |
| |
| private void checkAndSetConnectivityInstance() { |
| if (mCm == null) { |
| mCm = (ConnectivityManager) mContext.getSystemService(Context.CONNECTIVITY_SERVICE); |
| } |
| } |
| |
| private boolean startTethering(ArrayList<String> available) { |
| |
| boolean wifiAvailable = false; |
| |
| checkAndSetConnectivityInstance(); |
| |
| String[] wifiRegexs = mCm.getTetherableWifiRegexs(); |
| |
| for (String intf : available) { |
| for (String regex : wifiRegexs) { |
| if (intf.matches(regex)) { |
| |
| InterfaceConfiguration ifcg = null; |
| try { |
| ifcg = mNwService.getInterfaceConfig(intf); |
| if (ifcg != null) { |
| /* IP/netmask: 192.168.43.1/255.255.255.0 */ |
| ifcg.addr = new LinkAddress(NetworkUtils.numericToInetAddress( |
| "192.168.43.1"), 24); |
| ifcg.interfaceFlags = "[up]"; |
| |
| mNwService.setInterfaceConfig(intf, ifcg); |
| } |
| } catch (Exception e) { |
| Log.e(TAG, "Error configuring interface " + intf + ", :" + e); |
| return false; |
| } |
| |
| if(mCm.tether(intf) != ConnectivityManager.TETHER_ERROR_NO_ERROR) { |
| Log.e(TAG, "Error tethering on " + intf); |
| return false; |
| } |
| return true; |
| } |
| } |
| } |
| // We found no interfaces to tether |
| return false; |
| } |
| |
| private void stopTethering() { |
| |
| checkAndSetConnectivityInstance(); |
| |
| /* Clear the interface config to allow dhcp correctly configure new |
| ip settings */ |
| InterfaceConfiguration ifcg = null; |
| try { |
| ifcg = mNwService.getInterfaceConfig(mInterfaceName); |
| if (ifcg != null) { |
| ifcg.addr = new LinkAddress(NetworkUtils.numericToInetAddress( |
| "0.0.0.0"), 0); |
| mNwService.setInterfaceConfig(mInterfaceName, ifcg); |
| } |
| } catch (Exception e) { |
| Log.e(TAG, "Error resetting interface " + mInterfaceName + ", :" + e); |
| } |
| |
| if (mCm.untether(mInterfaceName) != ConnectivityManager.TETHER_ERROR_NO_ERROR) { |
| Log.e(TAG, "Untether initiate failed!"); |
| } |
| } |
| |
| /** |
| * Set the country code from the system setting value, if any. |
| */ |
| private void setCountryCode() { |
| String countryCode = Settings.Secure.getString(mContext.getContentResolver(), |
| Settings.Secure.WIFI_COUNTRY_CODE); |
| if (countryCode != null && !countryCode.isEmpty()) { |
| setCountryCode(countryCode, false); |
| } else { |
| //use driver default |
| } |
| } |
| |
| /** |
| * Set the frequency band from the system setting value, if any. |
| */ |
| private void setFrequencyBand() { |
| int band = Settings.Secure.getInt(mContext.getContentResolver(), |
| Settings.Secure.WIFI_FREQUENCY_BAND, WifiManager.WIFI_FREQUENCY_BAND_AUTO); |
| setFrequencyBand(band, false); |
| } |
| |
| private void setWifiState(int wifiState) { |
| final int previousWifiState = mWifiState.get(); |
| |
| try { |
| if (wifiState == WIFI_STATE_ENABLED) { |
| mBatteryStats.noteWifiOn(); |
| } else if (wifiState == WIFI_STATE_DISABLED) { |
| mBatteryStats.noteWifiOff(); |
| } |
| } catch (RemoteException e) { |
| Log.e(TAG, "Failed to note battery stats in wifi"); |
| } |
| |
| mWifiState.set(wifiState); |
| |
| if (DBG) Log.d(TAG, "setWifiState: " + syncGetWifiStateByName()); |
| |
| final Intent intent = new Intent(WifiManager.WIFI_STATE_CHANGED_ACTION); |
| intent.addFlags(Intent.FLAG_RECEIVER_REGISTERED_ONLY_BEFORE_BOOT); |
| intent.putExtra(WifiManager.EXTRA_WIFI_STATE, wifiState); |
| intent.putExtra(WifiManager.EXTRA_PREVIOUS_WIFI_STATE, previousWifiState); |
| mContext.sendStickyBroadcast(intent); |
| } |
| |
| private void setWifiApState(int wifiApState) { |
| final int previousWifiApState = mWifiApState.get(); |
| |
| try { |
| if (wifiApState == WIFI_AP_STATE_ENABLED) { |
| mBatteryStats.noteWifiOn(); |
| } else if (wifiApState == WIFI_AP_STATE_DISABLED) { |
| mBatteryStats.noteWifiOff(); |
| } |
| } catch (RemoteException e) { |
| Log.d(TAG, "Failed to note battery stats in wifi"); |
| } |
| |
| // Update state |
| mWifiApState.set(wifiApState); |
| |
| if (DBG) Log.d(TAG, "setWifiApState: " + syncGetWifiApStateByName()); |
| |
| final Intent intent = new Intent(WifiManager.WIFI_AP_STATE_CHANGED_ACTION); |
| intent.addFlags(Intent.FLAG_RECEIVER_REGISTERED_ONLY_BEFORE_BOOT); |
| intent.putExtra(WifiManager.EXTRA_WIFI_AP_STATE, wifiApState); |
| intent.putExtra(WifiManager.EXTRA_PREVIOUS_WIFI_AP_STATE, previousWifiApState); |
| mContext.sendStickyBroadcast(intent); |
| } |
| |
| /** |
| * Parse the scan result line passed to us by wpa_supplicant (helper). |
| * @param line the line to parse |
| * @return the {@link ScanResult} object |
| */ |
| private ScanResult parseScanResult(String line) { |
| ScanResult scanResult = null; |
| if (line != null) { |
| /* |
| * Cache implementation (LinkedHashMap) is not synchronized, thus, |
| * must synchronized here! |
| */ |
| synchronized (mScanResultCache) { |
| String[] result = scanResultPattern.split(line); |
| if (3 <= result.length && result.length <= 5) { |
| String bssid = result[0]; |
| // bssid | frequency | level | flags | ssid |
| int frequency; |
| int level; |
| try { |
| frequency = Integer.parseInt(result[1]); |
| level = Integer.parseInt(result[2]); |
| /* some implementations avoid negative values by adding 256 |
| * so we need to adjust for that here. |
| */ |
| if (level > 0) level -= 256; |
| } catch (NumberFormatException e) { |
| frequency = 0; |
| level = 0; |
| } |
| |
| /* |
| * The formatting of the results returned by |
| * wpa_supplicant is intended to make the fields |
| * line up nicely when printed, |
| * not to make them easy to parse. So we have to |
| * apply some heuristics to figure out which field |
| * is the SSID and which field is the flags. |
| */ |
| String ssid; |
| String flags; |
| if (result.length == 4) { |
| if (result[3].charAt(0) == '[') { |
| flags = result[3]; |
| ssid = ""; |
| } else { |
| flags = ""; |
| ssid = result[3]; |
| } |
| } else if (result.length == 5) { |
| flags = result[3]; |
| ssid = result[4]; |
| } else { |
| // Here, we must have 3 fields: no flags and ssid |
| // set |
| flags = ""; |
| ssid = ""; |
| } |
| |
| // bssid + ssid is the hash key |
| String key = bssid + ssid; |
| scanResult = mScanResultCache.get(key); |
| if (scanResult != null) { |
| scanResult.level = level; |
| scanResult.SSID = ssid; |
| scanResult.capabilities = flags; |
| scanResult.frequency = frequency; |
| } else { |
| // Do not add scan results that have no SSID set |
| if (0 < ssid.trim().length()) { |
| scanResult = |
| new ScanResult( |
| ssid, bssid, flags, level, frequency); |
| mScanResultCache.put(key, scanResult); |
| } |
| } |
| } else { |
| Log.w(TAG, "Misformatted scan result text with " + |
| result.length + " fields: " + line); |
| } |
| } |
| } |
| |
| return scanResult; |
| } |
| |
| /** |
| * scanResults input format |
| * 00:bb:cc:dd:cc:ee 2427 166 [WPA-EAP-TKIP][WPA2-EAP-CCMP] Net1 |
| * 00:bb:cc:dd:cc:ff 2412 165 [WPA-EAP-TKIP][WPA2-EAP-CCMP] Net2 |
| */ |
| private void setScanResults(String scanResults) { |
| if (scanResults == null) { |
| return; |
| } |
| |
| List<ScanResult> scanList = new ArrayList<ScanResult>(); |
| |
| int lineCount = 0; |
| |
| int scanResultsLen = scanResults.length(); |
| // Parse the result string, keeping in mind that the last line does |
| // not end with a newline. |
| for (int lineBeg = 0, lineEnd = 0; lineEnd <= scanResultsLen; ++lineEnd) { |
| if (lineEnd == scanResultsLen || scanResults.charAt(lineEnd) == '\n') { |
| ++lineCount; |
| |
| if (lineCount == 1) { |
| lineBeg = lineEnd + 1; |
| continue; |
| } |
| if (lineEnd > lineBeg) { |
| String line = scanResults.substring(lineBeg, lineEnd); |
| ScanResult scanResult = parseScanResult(line); |
| if (scanResult != null) { |
| scanList.add(scanResult); |
| } else { |
| //TODO: hidden network handling |
| } |
| } |
| lineBeg = lineEnd + 1; |
| } |
| } |
| |
| mScanResults = scanList; |
| } |
| |
| private String fetchSSID() { |
| String status = WifiNative.statusCommand(); |
| if (status == null) { |
| return null; |
| } |
| // extract ssid from a series of "name=value" |
| String[] lines = status.split("\n"); |
| for (String line : lines) { |
| String[] prop = line.split(" *= *"); |
| if (prop.length < 2) continue; |
| String name = prop[0]; |
| String value = prop[1]; |
| if (name.equalsIgnoreCase("ssid")) return value; |
| } |
| return null; |
| } |
| |
| /* |
| * Fetch RSSI and linkspeed on current connection |
| */ |
| private void fetchRssiAndLinkSpeedNative() { |
| int newRssi = WifiNative.getRssiCommand(); |
| if (newRssi != -1 && MIN_RSSI < newRssi && newRssi < MAX_RSSI) { // screen out invalid values |
| /* some implementations avoid negative values by adding 256 |
| * so we need to adjust for that here. |
| */ |
| if (newRssi > 0) newRssi -= 256; |
| mWifiInfo.setRssi(newRssi); |
| /* |
| * Rather then sending the raw RSSI out every time it |
| * changes, we precalculate the signal level that would |
| * be displayed in the status bar, and only send the |
| * broadcast if that much more coarse-grained number |
| * changes. This cuts down greatly on the number of |
| * broadcasts, at the cost of not mWifiInforming others |
| * interested in RSSI of all the changes in signal |
| * level. |
| */ |
| // TODO: The second arg to the call below needs to be a symbol somewhere, but |
| // it's actually the size of an array of icons that's private |
| // to StatusBar Policy. |
| int newSignalLevel = WifiManager.calculateSignalLevel(newRssi, 4); |
| if (newSignalLevel != mLastSignalLevel) { |
| sendRssiChangeBroadcast(newRssi); |
| } |
| mLastSignalLevel = newSignalLevel; |
| } else { |
| mWifiInfo.setRssi(MIN_RSSI); |
| } |
| int newLinkSpeed = WifiNative.getLinkSpeedCommand(); |
| if (newLinkSpeed != -1) { |
| mWifiInfo.setLinkSpeed(newLinkSpeed); |
| } |
| } |
| |
| private void setHighPerfModeEnabledNative(boolean enable) { |
| if(!WifiNative.setSuspendOptimizationsCommand(!enable)) { |
| Log.e(TAG, "set suspend optimizations failed!"); |
| } |
| if (enable) { |
| if (!WifiNative.setPowerModeCommand(POWER_MODE_ACTIVE)) { |
| Log.e(TAG, "set power mode active failed!"); |
| } |
| } else { |
| if (!WifiNative.setPowerModeCommand(POWER_MODE_AUTO)) { |
| Log.e(TAG, "set power mode auto failed!"); |
| } |
| } |
| } |
| |
| private void configureLinkProperties() { |
| if (WifiConfigStore.isUsingStaticIp(mLastNetworkId)) { |
| mLinkProperties = WifiConfigStore.getLinkProperties(mLastNetworkId); |
| } else { |
| synchronized (mDhcpInfoInternal) { |
| mLinkProperties = mDhcpInfoInternal.makeLinkProperties(); |
| } |
| mLinkProperties.setHttpProxy(WifiConfigStore.getProxyProperties(mLastNetworkId)); |
| } |
| mLinkProperties.setInterfaceName(mInterfaceName); |
| Log.d(TAG, "netId=" + mLastNetworkId + " Link configured: " + mLinkProperties.toString()); |
| } |
| |
| private int getMaxDhcpRetries() { |
| return Settings.Secure.getInt(mContext.getContentResolver(), |
| Settings.Secure.WIFI_MAX_DHCP_RETRY_COUNT, |
| DEFAULT_MAX_DHCP_RETRIES); |
| } |
| |
| private void sendScanResultsAvailableBroadcast() { |
| Intent intent = new Intent(WifiManager.SCAN_RESULTS_AVAILABLE_ACTION); |
| intent.addFlags(Intent.FLAG_RECEIVER_REGISTERED_ONLY_BEFORE_BOOT); |
| mContext.sendBroadcast(intent); |
| } |
| |
| private void sendRssiChangeBroadcast(final int newRssi) { |
| Intent intent = new Intent(WifiManager.RSSI_CHANGED_ACTION); |
| intent.addFlags(Intent.FLAG_RECEIVER_REGISTERED_ONLY_BEFORE_BOOT); |
| intent.putExtra(WifiManager.EXTRA_NEW_RSSI, newRssi); |
| mContext.sendBroadcast(intent); |
| } |
| |
| private void sendNetworkStateChangeBroadcast(String bssid) { |
| Intent intent = new Intent(WifiManager.NETWORK_STATE_CHANGED_ACTION); |
| intent.addFlags(Intent.FLAG_RECEIVER_REGISTERED_ONLY_BEFORE_BOOT |
| | Intent.FLAG_RECEIVER_REPLACE_PENDING); |
| intent.putExtra(WifiManager.EXTRA_NETWORK_INFO, mNetworkInfo); |
| intent.putExtra(WifiManager.EXTRA_LINK_PROPERTIES, new LinkProperties (mLinkProperties)); |
| if (bssid != null) |
| intent.putExtra(WifiManager.EXTRA_BSSID, bssid); |
| if (mNetworkInfo.getState() == NetworkInfo.State.CONNECTED) |
| intent.putExtra(WifiManager.EXTRA_WIFI_INFO, new WifiInfo(mWifiInfo)); |
| mContext.sendStickyBroadcast(intent); |
| } |
| |
| private void sendErrorBroadcast(int errorCode) { |
| Intent intent = new Intent(WifiManager.ERROR_ACTION); |
| intent.addFlags(Intent.FLAG_RECEIVER_REGISTERED_ONLY_BEFORE_BOOT); |
| intent.putExtra(WifiManager.EXTRA_ERROR_CODE, errorCode); |
| mContext.sendBroadcast(intent); |
| } |
| |
| private void sendLinkConfigurationChangedBroadcast() { |
| Intent intent = new Intent(WifiManager.LINK_CONFIGURATION_CHANGED_ACTION); |
| intent.addFlags(Intent.FLAG_RECEIVER_REGISTERED_ONLY_BEFORE_BOOT); |
| intent.putExtra(WifiManager.EXTRA_LINK_PROPERTIES, new LinkProperties(mLinkProperties)); |
| mContext.sendBroadcast(intent); |
| } |
| |
| private void sendSupplicantConnectionChangedBroadcast(boolean connected) { |
| Intent intent = new Intent(WifiManager.SUPPLICANT_CONNECTION_CHANGE_ACTION); |
| intent.addFlags(Intent.FLAG_RECEIVER_REGISTERED_ONLY_BEFORE_BOOT); |
| intent.putExtra(WifiManager.EXTRA_SUPPLICANT_CONNECTED, connected); |
| mContext.sendBroadcast(intent); |
| } |
| |
| /** |
| * Record the detailed state of a network. |
| * @param state the new @{code DetailedState} |
| */ |
| private void setNetworkDetailedState(NetworkInfo.DetailedState state) { |
| Log.d(TAG, "setDetailed state, old =" |
| + mNetworkInfo.getDetailedState() + " and new state=" + state); |
| if (state != mNetworkInfo.getDetailedState()) { |
| mNetworkInfo.setDetailedState(state, null, null); |
| } |
| } |
| |
| private DetailedState getNetworkDetailedState() { |
| return mNetworkInfo.getDetailedState(); |
| } |
| |
| |
| private SupplicantState handleSupplicantStateChange(Message message) { |
| StateChangeResult stateChangeResult = (StateChangeResult) message.obj; |
| SupplicantState state = stateChangeResult.state; |
| // Supplicant state change |
| // [31-13] Reserved for future use |
| // [8 - 0] Supplicant state (as defined in SupplicantState.java) |
| // 50023 supplicant_state_changed (custom|1|5) |
| EventLog.writeEvent(EVENTLOG_SUPPLICANT_STATE_CHANGED, state.ordinal()); |
| mWifiInfo.setSupplicantState(state); |
| // Network id is only valid when we start connecting |
| if (SupplicantState.isConnecting(state)) { |
| mWifiInfo.setNetworkId(stateChangeResult.networkId); |
| } else { |
| mWifiInfo.setNetworkId(WifiConfiguration.INVALID_NETWORK_ID); |
| } |
| |
| if (state == SupplicantState.ASSOCIATING) { |
| /* BSSID is valid only in ASSOCIATING state */ |
| mWifiInfo.setBSSID(stateChangeResult.BSSID); |
| } |
| |
| mSupplicantStateTracker.sendMessage(Message.obtain(message)); |
| mWpsStateMachine.sendMessage(Message.obtain(message)); |
| |
| return state; |
| } |
| |
| /** |
| * Resets the Wi-Fi Connections by clearing any state, resetting any sockets |
| * using the interface, stopping DHCP & disabling interface |
| */ |
| private void handleNetworkDisconnect() { |
| Log.d(TAG, "Stopping DHCP and clearing IP"); |
| |
| /* |
| * stop DHCP |
| */ |
| if (mDhcpStateMachine != null) { |
| mDhcpStateMachine.sendMessage(DhcpStateMachine.CMD_STOP_DHCP); |
| mDhcpStateMachine.quit(); |
| mDhcpStateMachine = null; |
| } |
| |
| try { |
| mNwService.clearInterfaceAddresses(mInterfaceName); |
| } catch (Exception e) { |
| Log.e(TAG, "Failed to clear IP addresses on disconnect" + e); |
| } |
| |
| /* Reset data structures */ |
| mWifiInfo.setInetAddress(null); |
| mWifiInfo.setBSSID(null); |
| mWifiInfo.setSSID(null); |
| mWifiInfo.setNetworkId(WifiConfiguration.INVALID_NETWORK_ID); |
| mWifiInfo.setRssi(MIN_RSSI); |
| mWifiInfo.setLinkSpeed(-1); |
| mWifiInfo.setExplicitConnect(false); |
| |
| /* send event to CM & network change broadcast */ |
| setNetworkDetailedState(DetailedState.DISCONNECTED); |
| sendNetworkStateChangeBroadcast(mLastBssid); |
| |
| /* Clear network properties */ |
| mLinkProperties.clear(); |
| /* Clear IP settings if the network used DHCP */ |
| if (!WifiConfigStore.isUsingStaticIp(mLastNetworkId)) { |
| WifiConfigStore.clearIpConfiguration(mLastNetworkId); |
| } |
| |
| mLastBssid= null; |
| mLastNetworkId = WifiConfiguration.INVALID_NETWORK_ID; |
| } |
| |
| void handlePreDhcpSetup() { |
| if (!mBluetoothConnectionActive) { |
| /* |
| * There are problems setting the Wi-Fi driver's power |
| * mode to active when bluetooth coexistence mode is |
| * enabled or sense. |
| * <p> |
| * We set Wi-Fi to active mode when |
| * obtaining an IP address because we've found |
| * compatibility issues with some routers with low power |
| * mode. |
| * <p> |
| * In order for this active power mode to properly be set, |
| * we disable coexistence mode until we're done with |
| * obtaining an IP address. One exception is if we |
| * are currently connected to a headset, since disabling |
| * coexistence would interrupt that connection. |
| */ |
| // Disable the coexistence mode |
| WifiNative.setBluetoothCoexistenceModeCommand( |
| WifiNative.BLUETOOTH_COEXISTENCE_MODE_DISABLED); |
| } |
| |
| mPowerMode = WifiNative.getPowerModeCommand(); |
| if (mPowerMode < 0) { |
| // Handle the case where supplicant driver does not support |
| // getPowerModeCommand. |
| mPowerMode = WifiStateMachine.POWER_MODE_AUTO; |
| } |
| if (mPowerMode != WifiStateMachine.POWER_MODE_ACTIVE) { |
| WifiNative.setPowerModeCommand(WifiStateMachine.POWER_MODE_ACTIVE); |
| } |
| } |
| |
| |
| void handlePostDhcpSetup() { |
| /* restore power mode */ |
| WifiNative.setPowerModeCommand(mPowerMode); |
| |
| // Set the coexistence mode back to its default value |
| WifiNative.setBluetoothCoexistenceModeCommand( |
| WifiNative.BLUETOOTH_COEXISTENCE_MODE_SENSE); |
| } |
| |
| private void handleSuccessfulIpConfiguration(DhcpInfoInternal dhcpInfoInternal) { |
| synchronized (mDhcpInfoInternal) { |
| mDhcpInfoInternal = dhcpInfoInternal; |
| } |
| mLastSignalLevel = -1; // force update of signal strength |
| WifiConfigStore.setIpConfiguration(mLastNetworkId, dhcpInfoInternal); |
| InetAddress addr = NetworkUtils.numericToInetAddress(dhcpInfoInternal.ipAddress); |
| mWifiInfo.setInetAddress(addr); |
| if (getNetworkDetailedState() == DetailedState.CONNECTED) { |
| //DHCP renewal in connected state |
| LinkProperties linkProperties = dhcpInfoInternal.makeLinkProperties(); |
| linkProperties.setHttpProxy(WifiConfigStore.getProxyProperties(mLastNetworkId)); |
| linkProperties.setInterfaceName(mInterfaceName); |
| if (!linkProperties.equals(mLinkProperties)) { |
| Log.d(TAG, "Link configuration changed for netId: " + mLastNetworkId |
| + " old: " + mLinkProperties + "new: " + linkProperties); |
| mLinkProperties = linkProperties; |
| sendLinkConfigurationChangedBroadcast(); |
| } |
| } else { |
| configureLinkProperties(); |
| setNetworkDetailedState(DetailedState.CONNECTED); |
| sendNetworkStateChangeBroadcast(mLastBssid); |
| } |
| } |
| |
| private void handleFailedIpConfiguration() { |
| Log.e(TAG, "IP configuration failed"); |
| |
| mWifiInfo.setInetAddress(null); |
| /** |
| * If we've exceeded the maximum number of retries for DHCP |
| * to a given network, disable the network |
| */ |
| if (++mReconnectCount > getMaxDhcpRetries()) { |
| Log.e(TAG, "Failed " + |
| mReconnectCount + " times, Disabling " + mLastNetworkId); |
| WifiConfigStore.disableNetwork(mLastNetworkId, |
| WifiConfiguration.DISABLED_DHCP_FAILURE); |
| mReconnectCount = 0; |
| } |
| |
| /* DHCP times out after about 30 seconds, we do a |
| * disconnect and an immediate reconnect to try again |
| */ |
| WifiNative.disconnectCommand(); |
| WifiNative.reconnectCommand(); |
| } |
| |
| /* Current design is to not set the config on a running hostapd but instead |
| * stop and start tethering when user changes config on a running access point |
| * |
| * TODO: Add control channel setup through hostapd that allows changing config |
| * on a running daemon |
| */ |
| private boolean startSoftApWithConfig(WifiConfiguration config) { |
| if (config == null) { |
| config = WifiApConfigStore.getApConfiguration(); |
| } else { |
| WifiApConfigStore.setApConfiguration(config); |
| } |
| try { |
| mNwService.startAccessPoint(config, mInterfaceName, SOFTAP_IFACE); |
| } catch (Exception e) { |
| Log.e(TAG, "Exception in softap start " + e); |
| try { |
| mNwService.stopAccessPoint(mInterfaceName); |
| mNwService.startAccessPoint(config, mInterfaceName, SOFTAP_IFACE); |
| } catch (Exception e1) { |
| Log.e(TAG, "Exception in softap re-start " + e1); |
| return false; |
| } |
| } |
| return true; |
| } |
| |
| /******************************************************** |
| * HSM states |
| *******************************************************/ |
| |
| class DefaultState extends State { |
| @Override |
| public boolean processMessage(Message message) { |
| if (DBG) Log.d(TAG, getName() + message.toString() + "\n"); |
| switch (message.what) { |
| case AsyncChannel.CMD_CHANNEL_HALF_CONNECTED: |
| if (message.arg1 == AsyncChannel.STATUS_SUCCESSFUL) { |
| mWifiP2pChannel.sendMessage(AsyncChannel.CMD_CHANNEL_FULL_CONNECTION); |
| } else { |
| Log.e(TAG, "WifiP2pService connection failure, error=" + message.arg1); |
| } |
| break; |
| case AsyncChannel.CMD_CHANNEL_DISCONNECTED: |
| Log.e(TAG, "WifiP2pService channel lost, message.arg1 =" + message.arg1); |
| //TODO: Re-establish connection to state machine after a delay |
| //mWifiP2pChannel.connect(mContext, getHandler(), mWifiP2pManager.getMessenger()); |
| break; |
| case CMD_BLUETOOTH_ADAPTER_STATE_CHANGE: |
| mBluetoothConnectionActive = (message.arg1 != |
| BluetoothAdapter.STATE_DISCONNECTED); |
| break; |
| /* Synchronous call returns */ |
| case CMD_PING_SUPPLICANT: |
| case CMD_ENABLE_NETWORK: |
| case CMD_DISABLE_NETWORK: |
| case CMD_ADD_OR_UPDATE_NETWORK: |
| case CMD_REMOVE_NETWORK: |
| case CMD_SAVE_CONFIG: |
| mReplyChannel.replyToMessage(message, message.what, FAILURE); |
| break; |
| case CMD_ENABLE_RSSI_POLL: |
| mEnableRssiPolling = (message.arg1 == 1); |
| break; |
| case CMD_ENABLE_BACKGROUND_SCAN: |
| mEnableBackgroundScan = (message.arg1 == 1); |
| break; |
| case CMD_SET_AP_CONFIG: |
| WifiApConfigStore.setApConfiguration((WifiConfiguration) message.obj); |
| break; |
| case CMD_GET_AP_CONFIG: |
| WifiConfiguration config = WifiApConfigStore.getApConfiguration(); |
| mReplyChannel.replyToMessage(message, message.what, config); |
| break; |
| /* Discard */ |
| case CMD_LOAD_DRIVER: |
| case CMD_UNLOAD_DRIVER: |
| case CMD_START_SUPPLICANT: |
| case CMD_STOP_SUPPLICANT: |
| case CMD_START_DRIVER: |
| case CMD_STOP_DRIVER: |
| case CMD_START_AP: |
| case CMD_START_AP_SUCCESS: |
| case CMD_START_AP_FAILURE: |
| case CMD_STOP_AP: |
| case CMD_TETHER_INTERFACE: |
| case CMD_START_SCAN: |
| case CMD_DISCONNECT: |
| case CMD_RECONNECT: |
| case CMD_REASSOCIATE: |
| case WifiMonitor.SUP_CONNECTION_EVENT: |
| case WifiMonitor.SUP_DISCONNECTION_EVENT: |
| case WifiMonitor.NETWORK_CONNECTION_EVENT: |
| case WifiMonitor.NETWORK_DISCONNECTION_EVENT: |
| case WifiMonitor.SCAN_RESULTS_EVENT: |
| case WifiMonitor.SUPPLICANT_STATE_CHANGE_EVENT: |
| case WifiMonitor.AUTHENTICATION_FAILURE_EVENT: |
| case WifiMonitor.WPS_OVERLAP_EVENT: |
| case CMD_BLACKLIST_NETWORK: |
| case CMD_CLEAR_BLACKLIST: |
| case CMD_SET_SCAN_MODE: |
| case CMD_SET_SCAN_TYPE: |
| case CMD_SET_HIGH_PERF_MODE: |
| case CMD_SET_COUNTRY_CODE: |
| case CMD_SET_FREQUENCY_BAND: |
| case CMD_REQUEST_CM_WAKELOCK: |
| case CMD_CONNECT_NETWORK: |
| case CMD_SAVE_NETWORK: |
| case CMD_FORGET_NETWORK: |
| case CMD_RSSI_POLL: |
| case CMD_ENABLE_ALL_NETWORKS: |
| case DhcpStateMachine.CMD_PRE_DHCP_ACTION: |
| case DhcpStateMachine.CMD_POST_DHCP_ACTION: |
| break; |
| case WifiMonitor.DRIVER_HUNG_EVENT: |
| setWifiEnabled(false); |
| setWifiEnabled(true); |
| break; |
| case CMD_START_WPS: |
| /* Return failure when the state machine cannot handle WPS initiation*/ |
| mReplyChannel.replyToMessage(message, WifiManager.CMD_WPS_COMPLETED, |
| new WpsResult(Status.FAILURE)); |
| break; |
| case WifiP2pService.P2P_ENABLE_PENDING: |
| // turn off wifi and defer to be handled in DriverUnloadedState |
| setWifiEnabled(false); |
| deferMessage(message); |
| break; |
| default: |
| Log.e(TAG, "Error! unhandled message" + message); |
| break; |
| } |
| return HANDLED; |
| } |
| } |
| |
| class InitialState extends State { |
| @Override |
| //TODO: could move logging into a common class |
| public void enter() { |
| if (DBG) Log.d(TAG, getName() + "\n"); |
| // [31-8] Reserved for future use |
| // [7 - 0] HSM state change |
| // 50021 wifi_state_changed (custom|1|5) |
| EventLog.writeEvent(EVENTLOG_WIFI_STATE_CHANGED, getName()); |
| |
| WifiApConfigStore.initialize(mContext); |
| |
| if (WifiNative.isDriverLoaded()) { |
| transitionTo(mDriverLoadedState); |
| } |
| else { |
| transitionTo(mDriverUnloadedState); |
| } |
| |
| //Connect to WifiP2pService |
| mWifiP2pManager = (WifiP2pManager) mContext.getSystemService(Context.WIFI_P2P_SERVICE); |
| mWifiP2pChannel.connect(mContext, getHandler(), mWifiP2pManager.getMessenger()); |
| |
| } |
| } |
| |
| class DriverLoadingState extends State { |
| @Override |
| public void enter() { |
| if (DBG) Log.d(TAG, getName() + "\n"); |
| EventLog.writeEvent(EVENTLOG_WIFI_STATE_CHANGED, getName()); |
| |
| final Message message = new Message(); |
| message.copyFrom(getCurrentMessage()); |
| /* TODO: add a timeout to fail when driver load is hung. |
| * Similarly for driver unload. |
| */ |
| new Thread(new Runnable() { |
| public void run() { |
| mWakeLock.acquire(); |
| //enabling state |
| switch(message.arg1) { |
| case WIFI_STATE_ENABLING: |
| setWifiState(WIFI_STATE_ENABLING); |
| break; |
| case WIFI_AP_STATE_ENABLING: |
| setWifiApState(WIFI_AP_STATE_ENABLING); |
| break; |
| } |
| |
| if(WifiNative.loadDriver()) { |
| Log.d(TAG, "Driver load successful"); |
| sendMessage(CMD_LOAD_DRIVER_SUCCESS); |
| } else { |
| Log.e(TAG, "Failed to load driver!"); |
| switch(message.arg1) { |
| case WIFI_STATE_ENABLING: |
| setWifiState(WIFI_STATE_UNKNOWN); |
| break; |
| case WIFI_AP_STATE_ENABLING: |
| setWifiApState(WIFI_AP_STATE_FAILED); |
| break; |
| } |
| sendMessage(CMD_LOAD_DRIVER_FAILURE); |
| } |
| mWakeLock.release(); |
| } |
| }).start(); |
| } |
| |
| @Override |
| public boolean processMessage(Message message) { |
| if (DBG) Log.d(TAG, getName() + message.toString() + "\n"); |
| switch (message.what) { |
| case CMD_LOAD_DRIVER_SUCCESS: |
| transitionTo(mDriverLoadedState); |
| break; |
| case CMD_LOAD_DRIVER_FAILURE: |
| transitionTo(mDriverFailedState); |
| break; |
| case CMD_LOAD_DRIVER: |
| case CMD_UNLOAD_DRIVER: |
| case CMD_START_SUPPLICANT: |
| case CMD_STOP_SUPPLICANT: |
| case CMD_START_AP: |
| case CMD_STOP_AP: |
| case CMD_START_DRIVER: |
| case CMD_STOP_DRIVER: |
| case CMD_SET_SCAN_MODE: |
| case CMD_SET_SCAN_TYPE: |
| case CMD_SET_HIGH_PERF_MODE: |
| case CMD_SET_COUNTRY_CODE: |
| case CMD_SET_FREQUENCY_BAND: |
| case CMD_START_PACKET_FILTERING: |
| case CMD_STOP_PACKET_FILTERING: |
| deferMessage(message); |
| break; |
| default: |
| return NOT_HANDLED; |
| } |
| EventLog.writeEvent(EVENTLOG_WIFI_EVENT_HANDLED, message.what); |
| return HANDLED; |
| } |
| } |
| |
| class DriverLoadedState extends State { |
| @Override |
| public void enter() { |
| if (DBG) Log.d(TAG, getName() + "\n"); |
| EventLog.writeEvent(EVENTLOG_WIFI_STATE_CHANGED, getName()); |
| } |
| @Override |
| public boolean processMessage(Message message) { |
| if (DBG) Log.d(TAG, getName() + message.toString() + "\n"); |
| switch(message.what) { |
| case CMD_UNLOAD_DRIVER: |
| transitionTo(mDriverUnloadingState); |
| break; |
| case CMD_START_SUPPLICANT: |
| try { |
| mNwService.wifiFirmwareReload(mInterfaceName, "STA"); |
| } catch (Exception e) { |
| Log.e(TAG, "Failed to reload STA firmware " + e); |
| // continue |
| } |
| //A runtime crash can leave the interface up and |
| //this affects connectivity when supplicant starts up. |
| //Ensure interface is down before a supplicant start. |
| try { |
| mNwService.setInterfaceDown(mInterfaceName); |
| } catch (RemoteException re) { |
| if (DBG) Log.w(TAG, "Unable to bring down wlan interface: " + re); |
| } catch (IllegalStateException ie) { |
| if (DBG) Log.w(TAG, "Unable to bring down wlan interface: " + ie); |
| } |
| |
| if(WifiNative.startSupplicant()) { |
| Log.d(TAG, "Supplicant start successful"); |
| mWifiMonitor.startMonitoring(); |
| transitionTo(mSupplicantStartingState); |
| } else { |
| Log.e(TAG, "Failed to start supplicant!"); |
| sendMessage(obtainMessage(CMD_UNLOAD_DRIVER, WIFI_STATE_UNKNOWN, 0)); |
| } |
| break; |
| case CMD_START_AP: |
| transitionTo(mSoftApStartingState); |
| break; |
| default: |
| return NOT_HANDLED; |
| } |
| EventLog.writeEvent(EVENTLOG_WIFI_EVENT_HANDLED, message.what); |
| return HANDLED; |
| } |
| } |
| |
| class DriverUnloadingState extends State { |
| @Override |
| public void enter() { |
| if (DBG) Log.d(TAG, getName() + "\n"); |
| EventLog.writeEvent(EVENTLOG_WIFI_STATE_CHANGED, getName()); |
| |
| final Message message = new Message(); |
| message.copyFrom(getCurrentMessage()); |
| new Thread(new Runnable() { |
| public void run() { |
| if (DBG) Log.d(TAG, getName() + message.toString() + "\n"); |
| mWakeLock.acquire(); |
| if(WifiNative.unloadDriver()) { |
| Log.d(TAG, "Driver unload successful"); |
| sendMessage(CMD_UNLOAD_DRIVER_SUCCESS); |
| |
| switch(message.arg1) { |
| case WIFI_STATE_DISABLED: |
| case WIFI_STATE_UNKNOWN: |
| setWifiState(message.arg1); |
| break; |
| case WIFI_AP_STATE_DISABLED: |
| case WIFI_AP_STATE_FAILED: |
| setWifiApState(message.arg1); |
| break; |
| } |
| } else { |
| Log.e(TAG, "Failed to unload driver!"); |
| sendMessage(CMD_UNLOAD_DRIVER_FAILURE); |
| |
| switch(message.arg1) { |
| case WIFI_STATE_DISABLED: |
| case WIFI_STATE_UNKNOWN: |
| setWifiState(WIFI_STATE_UNKNOWN); |
| break; |
| case WIFI_AP_STATE_DISABLED: |
| case WIFI_AP_STATE_FAILED: |
| setWifiApState(WIFI_AP_STATE_FAILED); |
| break; |
| } |
| } |
| mWakeLock.release(); |
| } |
| }).start(); |
| } |
| |
| @Override |
| public boolean processMessage(Message message) { |
| if (DBG) Log.d(TAG, getName() + message.toString() + "\n"); |
| switch (message.what) { |
| case CMD_UNLOAD_DRIVER_SUCCESS: |
| transitionTo(mDriverUnloadedState); |
| break; |
| case CMD_UNLOAD_DRIVER_FAILURE: |
| transitionTo(mDriverFailedState); |
| break; |
| case CMD_LOAD_DRIVER: |
| case CMD_UNLOAD_DRIVER: |
| case CMD_START_SUPPLICANT: |
| case CMD_STOP_SUPPLICANT: |
| case CMD_START_AP: |
| case CMD_STOP_AP: |
| case CMD_START_DRIVER: |
| case CMD_STOP_DRIVER: |
| case CMD_SET_SCAN_MODE: |
| case CMD_SET_SCAN_TYPE: |
| case CMD_SET_HIGH_PERF_MODE: |
| case CMD_SET_COUNTRY_CODE: |
| case CMD_SET_FREQUENCY_BAND: |
| case CMD_START_PACKET_FILTERING: |
| case CMD_STOP_PACKET_FILTERING: |
| deferMessage(message); |
| break; |
| default: |
| return NOT_HANDLED; |
| } |
| EventLog.writeEvent(EVENTLOG_WIFI_EVENT_HANDLED, message.what); |
| return HANDLED; |
| } |
| } |
| |
| class DriverUnloadedState extends State { |
| @Override |
| public void enter() { |
| if (DBG) Log.d(TAG, getName() + "\n"); |
| EventLog.writeEvent(EVENTLOG_WIFI_STATE_CHANGED, getName()); |
| } |
| @Override |
| public boolean processMessage(Message message) { |
| if (DBG) Log.d(TAG, getName() + message.toString() + "\n"); |
| switch (message.what) { |
| case CMD_LOAD_DRIVER: |
| mWifiP2pChannel.sendMessage(WIFI_ENABLE_PENDING); |
| transitionTo(mWaitForP2pDisableState); |
| break; |
| case WifiP2pService.P2P_ENABLE_PENDING: |
| mReplyChannel.replyToMessage(message, P2P_ENABLE_PROCEED); |
| break; |
| default: |
| return NOT_HANDLED; |
| } |
| EventLog.writeEvent(EVENTLOG_WIFI_EVENT_HANDLED, message.what); |
| return HANDLED; |
| } |
| } |
| |
| class DriverFailedState extends State { |
| @Override |
| public void enter() { |
| Log.e(TAG, getName() + "\n"); |
| EventLog.writeEvent(EVENTLOG_WIFI_STATE_CHANGED, getName()); |
| } |
| @Override |
| public boolean processMessage(Message message) { |
| if (DBG) Log.d(TAG, getName() + message.toString() + "\n"); |
| return NOT_HANDLED; |
| } |
| } |
| |
| |
| class SupplicantStartingState extends State { |
| @Override |
| public void enter() { |
| if (DBG) Log.d(TAG, getName() + "\n"); |
| EventLog.writeEvent(EVENTLOG_WIFI_STATE_CHANGED, getName()); |
| } |
| @Override |
| public boolean processMessage(Message message) { |
| if (DBG) Log.d(TAG, getName() + message.toString() + "\n"); |
| switch(message.what) { |
| case WifiMonitor.SUP_CONNECTION_EVENT: |
| Log.d(TAG, "Supplicant connection established"); |
| setWifiState(WIFI_STATE_ENABLED); |
| mSupplicantRestartCount = 0; |
| /* Reset the supplicant state to indicate the supplicant |
| * state is not known at this time */ |
| mSupplicantStateTracker.sendMessage(CMD_RESET_SUPPLICANT_STATE); |
| mWpsStateMachine.sendMessage(CMD_RESET_WPS_STATE); |
| /* Initialize data structures */ |
| mLastBssid = null; |
| mLastNetworkId = WifiConfiguration.INVALID_NETWORK_ID; |
| mLastSignalLevel = -1; |
| |
| mWifiInfo.setMacAddress(WifiNative.getMacAddressCommand()); |
| |
| WifiConfigStore.initialize(mContext); |
| |
| sendSupplicantConnectionChangedBroadcast(true); |
| transitionTo(mDriverStartedState); |
| break; |
| case WifiMonitor.SUP_DISCONNECTION_EVENT: |
| if (++mSupplicantRestartCount <= SUPPLICANT_RESTART_TRIES) { |
| Log.e(TAG, "Failed to setup control channel, restart supplicant"); |
| WifiNative.killSupplicant(); |
| transitionTo(mDriverLoadedState); |
| sendMessageDelayed(CMD_START_SUPPLICANT, SUPPLICANT_RESTART_INTERVAL_MSECS); |
| } else { |
| Log.e(TAG, "Failed " + mSupplicantRestartCount + |
| " times to start supplicant, unload driver"); |
| mSupplicantRestartCount = 0; |
| transitionTo(mDriverLoadedState); |
| sendMessage(obtainMessage(CMD_UNLOAD_DRIVER, WIFI_STATE_UNKNOWN, 0)); |
| } |
| break; |
| case CMD_LOAD_DRIVER: |
| case CMD_UNLOAD_DRIVER: |
| case CMD_START_SUPPLICANT: |
| case CMD_STOP_SUPPLICANT: |
| case CMD_START_AP: |
| case CMD_STOP_AP: |
| case CMD_START_DRIVER: |
| case CMD_STOP_DRIVER: |
| case CMD_SET_SCAN_MODE: |
| case CMD_SET_SCAN_TYPE: |
| case CMD_SET_HIGH_PERF_MODE: |
| case CMD_SET_COUNTRY_CODE: |
| case CMD_SET_FREQUENCY_BAND: |
| case CMD_START_PACKET_FILTERING: |
| case CMD_STOP_PACKET_FILTERING: |
| deferMessage(message); |
| break; |
| default: |
| return NOT_HANDLED; |
| } |
| EventLog.writeEvent(EVENTLOG_WIFI_EVENT_HANDLED, message.what); |
| return HANDLED; |
| } |
| } |
| |
| class SupplicantStartedState extends State { |
| @Override |
| public void enter() { |
| if (DBG) Log.d(TAG, getName() + "\n"); |
| EventLog.writeEvent(EVENTLOG_WIFI_STATE_CHANGED, getName()); |
| /* Initialize for connect mode operation at start */ |
| mIsScanMode = false; |
| /* Wifi is available as long as we have a connection to supplicant */ |
| mNetworkInfo.setIsAvailable(true); |
| /* Set scan interval */ |
| long supplicantScanIntervalMs = Settings.Secure.getLong(mContext.getContentResolver(), |
| Settings.Secure.WIFI_SUPPLICANT_SCAN_INTERVAL_MS, |
| mDefaultSupplicantScanIntervalMs); |
| WifiNative.setScanIntervalCommand((int)supplicantScanIntervalMs / 1000); |
| } |
| @Override |
| public boolean processMessage(Message message) { |
| if (DBG) Log.d(TAG, getName() + message.toString() + "\n"); |
| WifiConfiguration config; |
| boolean eventLoggingEnabled = true; |
| switch(message.what) { |
| case CMD_STOP_SUPPLICANT: /* Supplicant stopped by user */ |
| transitionTo(mSupplicantStoppingState); |
| break; |
| case WifiMonitor.SUP_DISCONNECTION_EVENT: /* Supplicant connection lost */ |
| Log.e(TAG, "Connection lost, restart supplicant"); |
| WifiNative.killSupplicant(); |
| WifiNative.closeSupplicantConnection(); |
| mNetworkInfo.setIsAvailable(false); |
| handleNetworkDisconnect(); |
| sendSupplicantConnectionChangedBroadcast(false); |
| mSupplicantStateTracker.sendMessage(CMD_RESET_SUPPLICANT_STATE); |
| mWpsStateMachine.sendMessage(CMD_RESET_WPS_STATE); |
| transitionTo(mDriverLoadedState); |
| sendMessageDelayed(CMD_START_SUPPLICANT, SUPPLICANT_RESTART_INTERVAL_MSECS); |
| break; |
| case WifiMonitor.SCAN_RESULTS_EVENT: |
| eventLoggingEnabled = false; |
| setScanResults(WifiNative.scanResultsCommand()); |
| sendScanResultsAvailableBroadcast(); |
| mScanResultIsPending = false; |
| break; |
| case CMD_PING_SUPPLICANT: |
| boolean ok = WifiNative.pingCommand(); |
| mReplyChannel.replyToMessage(message, message.what, ok ? SUCCESS : FAILURE); |
| break; |
| case CMD_ADD_OR_UPDATE_NETWORK: |
| config = (WifiConfiguration) message.obj; |
| mReplyChannel.replyToMessage(message, CMD_ADD_OR_UPDATE_NETWORK, |
| WifiConfigStore.addOrUpdateNetwork(config)); |
| break; |
| case CMD_REMOVE_NETWORK: |
| ok = WifiConfigStore.removeNetwork(message.arg1); |
| mReplyChannel.replyToMessage(message, message.what, ok ? SUCCESS : FAILURE); |
| break; |
| case CMD_ENABLE_NETWORK: |
| ok = WifiConfigStore.enableNetwork(message.arg1, message.arg2 == 1); |
| mReplyChannel.replyToMessage(message, message.what, ok ? SUCCESS : FAILURE); |
| break; |
| case CMD_ENABLE_ALL_NETWORKS: |
| WifiConfigStore.enableAllNetworks(); |
| break; |
| case CMD_DISABLE_NETWORK: |
| ok = WifiConfigStore.disableNetwork(message.arg1, message.arg2); |
| mReplyChannel.replyToMessage(message, message.what, ok ? SUCCESS : FAILURE); |
| break; |
| case CMD_BLACKLIST_NETWORK: |
| WifiNative.addToBlacklistCommand((String)message.obj); |
| break; |
| case CMD_CLEAR_BLACKLIST: |
| WifiNative.clearBlacklistCommand(); |
| break; |
| case CMD_SAVE_CONFIG: |
| ok = WifiConfigStore.saveConfig(); |
| mReplyChannel.replyToMessage(message, CMD_SAVE_CONFIG, ok ? SUCCESS : FAILURE); |
| |
| // Inform the backup manager about a data change |
| IBackupManager ibm = IBackupManager.Stub.asInterface( |
| ServiceManager.getService(Context.BACKUP_SERVICE)); |
| if (ibm != null) { |
| try { |
| ibm.dataChanged("com.android.providers.settings"); |
| } catch (Exception e) { |
| // Try again later |
| } |
| } |
| break; |
| /* Cannot start soft AP while in client mode */ |
| case CMD_START_AP: |
| Log.d(TAG, "Failed to start soft AP with a running supplicant"); |
| setWifiApState(WIFI_AP_STATE_FAILED); |
| break; |
| case CMD_SET_SCAN_MODE: |
| mIsScanMode = (message.arg1 == SCAN_ONLY_MODE); |
| break; |
| case CMD_SAVE_NETWORK: |
| config = (WifiConfiguration) message.obj; |
| WifiConfigStore.saveNetwork(config); |
| break; |
| case CMD_FORGET_NETWORK: |
| WifiConfigStore.forgetNetwork(message.arg1); |
| break; |
| default: |
| return NOT_HANDLED; |
| } |
| if (eventLoggingEnabled) { |
| EventLog.writeEvent(EVENTLOG_WIFI_EVENT_HANDLED, message.what); |
| } |
| return HANDLED; |
| } |
| |
| @Override |
| public void exit() { |
| mNetworkInfo.setIsAvailable(false); |
| } |
| } |
| |
| class SupplicantStoppingState extends State { |
| @Override |
| public void enter() { |
| if (DBG) Log.d(TAG, getName() + "\n"); |
| EventLog.writeEvent(EVENTLOG_WIFI_STATE_CHANGED, getName()); |
| Log.d(TAG, "stopping supplicant"); |
| if (!WifiNative.stopSupplicant()) { |
| Log.e(TAG, "Failed to stop supplicant, issue kill"); |
| WifiNative.killSupplicant(); |
| } |
| mNetworkInfo.setIsAvailable(false); |
| handleNetworkDisconnect(); |
| setWifiState(WIFI_STATE_DISABLING); |
| sendSupplicantConnectionChangedBroadcast(false); |
| mSupplicantStateTracker.sendMessage(CMD_RESET_SUPPLICANT_STATE); |
| mWpsStateMachine.sendMessage(CMD_RESET_WPS_STATE); |
| } |
| @Override |
| public boolean processMessage(Message message) { |
| if (DBG) Log.d(TAG, getName() + message.toString() + "\n"); |
| switch(message.what) { |
| case WifiMonitor.SUP_CONNECTION_EVENT: |
| Log.e(TAG, "Supplicant connection received while stopping"); |
| break; |
| case WifiMonitor.SUP_DISCONNECTION_EVENT: |
| Log.d(TAG, "Supplicant connection lost"); |
| WifiNative.closeSupplicantConnection(); |
| transitionTo(mDriverLoadedState); |
| break; |
| case CMD_LOAD_DRIVER: |
| case CMD_UNLOAD_DRIVER: |
| case CMD_START_SUPPLICANT: |
| case CMD_STOP_SUPPLICANT: |
| case CMD_START_AP: |
| case CMD_STOP_AP: |
| case CMD_START_DRIVER: |
| case CMD_STOP_DRIVER: |
| case CMD_SET_SCAN_MODE: |
| case CMD_SET_SCAN_TYPE: |
| case CMD_SET_HIGH_PERF_MODE: |
| case CMD_SET_COUNTRY_CODE: |
| case CMD_SET_FREQUENCY_BAND: |
| case CMD_START_PACKET_FILTERING: |
| case CMD_STOP_PACKET_FILTERING: |
| deferMessage(message); |
| break; |
| default: |
| return NOT_HANDLED; |
| } |
| EventLog.writeEvent(EVENTLOG_WIFI_EVENT_HANDLED, message.what); |
| return HANDLED; |
| } |
| } |
| |
| class DriverStartingState extends State { |
| @Override |
| public void enter() { |
| if (DBG) Log.d(TAG, getName() + "\n"); |
| EventLog.writeEvent(EVENTLOG_WIFI_STATE_CHANGED, getName()); |
| } |
| @Override |
| public boolean processMessage(Message message) { |
| if (DBG) Log.d(TAG, getName() + message.toString() + "\n"); |
| switch(message.what) { |
| case WifiMonitor.SUPPLICANT_STATE_CHANGE_EVENT: |
| SupplicantState state = handleSupplicantStateChange(message); |
| /* If suplicant is exiting out of INTERFACE_DISABLED state into |
| * a state that indicates driver has started, it is ready to |
| * receive driver commands |
| */ |
| if (SupplicantState.isDriverActive(state)) { |
| transitionTo(mDriverStartedState); |
| } |
| break; |
| /* Queue driver commands & connection events */ |
| case CMD_START_DRIVER: |
| case CMD_STOP_DRIVER: |
| case WifiMonitor.NETWORK_CONNECTION_EVENT: |
| case WifiMonitor.NETWORK_DISCONNECTION_EVENT: |
| case WifiMonitor.AUTHENTICATION_FAILURE_EVENT: |
| case WifiMonitor.WPS_OVERLAP_EVENT: |
| case CMD_SET_SCAN_TYPE: |
| case CMD_SET_HIGH_PERF_MODE: |
| case CMD_SET_COUNTRY_CODE: |
| case CMD_SET_FREQUENCY_BAND: |
| case CMD_START_PACKET_FILTERING: |
| case CMD_STOP_PACKET_FILTERING: |
| case CMD_START_SCAN: |
| case CMD_DISCONNECT: |
| case CMD_REASSOCIATE: |
| case CMD_RECONNECT: |
| deferMessage(message); |
| break; |
| default: |
| return NOT_HANDLED; |
| } |
| EventLog.writeEvent(EVENTLOG_WIFI_EVENT_HANDLED, message.what); |
| return HANDLED; |
| } |
| } |
| |
| class DriverStartedState extends State { |
| @Override |
| public void enter() { |
| if (DBG) Log.d(TAG, getName() + "\n"); |
| EventLog.writeEvent(EVENTLOG_WIFI_STATE_CHANGED, getName()); |
| |
| mIsRunning = true; |
| updateBatteryWorkSource(null); |
| |
| /** |
| * Enable bluetooth coexistence scan mode when bluetooth connection is active. |
| * When this mode is on, some of the low-level scan parameters used by the |
| * driver are changed to reduce interference with bluetooth |
| */ |
| WifiNative.setBluetoothCoexistenceScanModeCommand(mBluetoothConnectionActive); |
| /* set country code */ |
| setCountryCode(); |
| /* set frequency band of operation */ |
| setFrequencyBand(); |
| /* initialize network state */ |
| setNetworkDetailedState(DetailedState.DISCONNECTED); |
| |
| /* Remove any filtering on Multicast v6 at start */ |
| WifiNative.stopFilteringMulticastV6Packets(); |
| |
| /* Reset Multicast v4 filtering state */ |
| if (mFilteringMulticastV4Packets.get()) { |
| WifiNative.startFilteringMulticastV4Packets(); |
| } else { |
| WifiNative.stopFilteringMulticastV4Packets(); |
| } |
| |
| if (mIsScanMode) { |
| WifiNative.setScanResultHandlingCommand(SCAN_ONLY_MODE); |
| WifiNative.disconnectCommand(); |
| transitionTo(mScanModeState); |
| } else { |
| WifiNative.setScanResultHandlingCommand(CONNECT_MODE); |
| WifiNative.reconnectCommand(); |
| transitionTo(mDisconnectedState); |
| } |
| } |
| @Override |
| public boolean processMessage(Message message) { |
| if (DBG) Log.d(TAG, getName() + message.toString() + "\n"); |
| boolean eventLoggingEnabled = true; |
| switch(message.what) { |
| case CMD_SET_SCAN_TYPE: |
| if (message.arg1 == SCAN_ACTIVE) { |
| WifiNative.setScanModeCommand(true); |
| } else { |
| WifiNative.setScanModeCommand(false); |
| } |
| break; |
| case CMD_START_SCAN: |
| eventLoggingEnabled = false; |
| WifiNative.scanCommand(message.arg1 == SCAN_ACTIVE); |
| mScanResultIsPending = true; |
| break; |
| case CMD_SET_HIGH_PERF_MODE: |
| setHighPerfModeEnabledNative(message.arg1 == 1); |
| break; |
| case CMD_SET_COUNTRY_CODE: |
| String country = (String) message.obj; |
| Log.d(TAG, "set country code " + country); |
| if (!WifiNative.setCountryCodeCommand(country.toUpperCase())) { |
| Log.e(TAG, "Failed to set country code " + country); |
| } |
| break; |
| case CMD_SET_FREQUENCY_BAND: |
| int band = message.arg1; |
| Log.d(TAG, "set frequency band " + band); |
| if (WifiNative.setBandCommand(band)) { |
| mFrequencyBand.set(band); |
| //Fetch the latest scan results when frequency band is set |
| startScan(true); |
| } else { |
| Log.e(TAG, "Failed to set frequency band " + band); |
| } |
| break; |
| case CMD_BLUETOOTH_ADAPTER_STATE_CHANGE: |
| mBluetoothConnectionActive = (message.arg1 != |
| BluetoothAdapter.STATE_DISCONNECTED); |
| WifiNative.setBluetoothCoexistenceScanModeCommand(mBluetoothConnectionActive); |
| break; |
| case CMD_STOP_DRIVER: |
| mWakeLock.acquire(); |
| WifiNative.stopDriverCommand(); |
| transitionTo(mDriverStoppingState); |
| mWakeLock.release(); |
| break; |
| case CMD_START_PACKET_FILTERING: |
| if (message.arg1 == MULTICAST_V6) { |
| WifiNative.startFilteringMulticastV6Packets(); |
| } else if (message.arg1 == MULTICAST_V4) { |
| WifiNative.startFilteringMulticastV4Packets(); |
| } else { |
| Log.e(TAG, "Illegal arugments to CMD_START_PACKET_FILTERING"); |
| } |
| break; |
| case CMD_STOP_PACKET_FILTERING: |
| if (message.arg1 == MULTICAST_V6) { |
| WifiNative.stopFilteringMulticastV6Packets(); |
| } else if (message.arg1 == MULTICAST_V4) { |
| WifiNative.stopFilteringMulticastV4Packets(); |
| } else { |
| Log.e(TAG, "Illegal arugments to CMD_STOP_PACKET_FILTERING"); |
| } |
| break; |
| default: |
| return NOT_HANDLED; |
| } |
| if (eventLoggingEnabled) { |
| EventLog.writeEvent(EVENTLOG_WIFI_EVENT_HANDLED, message.what); |
| } |
| return HANDLED; |
| } |
| @Override |
| public void exit() { |
| if (DBG) Log.d(TAG, getName() + "\n"); |
| mIsRunning = false; |
| updateBatteryWorkSource(null); |
| mScanResults = null; |
| } |
| } |
| |
| class DriverStoppingState extends State { |
| @Override |
| public void enter() { |
| if (DBG) Log.d(TAG, getName() + "\n"); |
| EventLog.writeEvent(EVENTLOG_WIFI_STATE_CHANGED, getName()); |
| } |
| @Override |
| public boolean processMessage(Message message) { |
| if (DBG) Log.d(TAG, getName() + message.toString() + "\n"); |
| switch(message.what) { |
| case WifiMonitor.SUPPLICANT_STATE_CHANGE_EVENT: |
| SupplicantState state = handleSupplicantStateChange(message); |
| if (state == SupplicantState.INTERFACE_DISABLED) { |
| transitionTo(mDriverStoppedState); |
| } |
| break; |
| /* Queue driver commands */ |
| case CMD_START_DRIVER: |
| case CMD_STOP_DRIVER: |
| case CMD_SET_SCAN_TYPE: |
| case CMD_SET_HIGH_PERF_MODE: |
| case CMD_SET_COUNTRY_CODE: |
| case CMD_SET_FREQUENCY_BAND: |
| case CMD_START_PACKET_FILTERING: |
| case CMD_STOP_PACKET_FILTERING: |
| case CMD_START_SCAN: |
| case CMD_DISCONNECT: |
| case CMD_REASSOCIATE: |
| case CMD_RECONNECT: |
| deferMessage(message); |
| break; |
| default: |
| return NOT_HANDLED; |
| } |
| EventLog.writeEvent(EVENTLOG_WIFI_EVENT_HANDLED, message.what); |
| return HANDLED; |
| } |
| } |
| |
| class DriverStoppedState extends State { |
| @Override |
| public void enter() { |
| if (DBG) Log.d(TAG, getName() + "\n"); |
| EventLog.writeEvent(EVENTLOG_WIFI_STATE_CHANGED, getName()); |
| } |
| @Override |
| public boolean processMessage(Message message) { |
| if (DBG) Log.d(TAG, getName() + message.toString() + "\n"); |
| switch (message.what) { |
| case CMD_START_DRIVER: |
| mWakeLock.acquire(); |
| WifiNative.startDriverCommand(); |
| mWakeLock.release(); |
| transitionTo(mDriverStartingState); |
| break; |
| default: |
| return NOT_HANDLED; |
| } |
| EventLog.writeEvent(EVENTLOG_WIFI_EVENT_HANDLED, message.what); |
| return HANDLED; |
| } |
| } |
| |
| class ScanModeState extends State { |
| @Override |
| public void enter() { |
| if (DBG) Log.d(TAG, getName() + "\n"); |
| EventLog.writeEvent(EVENTLOG_WIFI_STATE_CHANGED, getName()); |
| } |
| @Override |
| public boolean processMessage(Message message) { |
| if (DBG) Log.d(TAG, getName() + message.toString() + "\n"); |
| switch(message.what) { |
| case CMD_SET_SCAN_MODE: |
| if (message.arg1 == SCAN_ONLY_MODE) { |
| /* Ignore */ |
| return HANDLED; |
| } else { |
| WifiNative.setScanResultHandlingCommand(message.arg1); |
| WifiNative.reconnectCommand(); |
| mIsScanMode = false; |
| transitionTo(mDisconnectedState); |
| } |
| break; |
| /* Ignore */ |
| case CMD_DISCONNECT: |
| case CMD_RECONNECT: |
| case CMD_REASSOCIATE: |
| case WifiMonitor.SUPPLICANT_STATE_CHANGE_EVENT: |
| case WifiMonitor.NETWORK_CONNECTION_EVENT: |
| case WifiMonitor.NETWORK_DISCONNECTION_EVENT: |
| break; |
| default: |
| return NOT_HANDLED; |
| } |
| EventLog.writeEvent(EVENTLOG_WIFI_EVENT_HANDLED, message.what); |
| return HANDLED; |
| } |
| } |
| |
| class ConnectModeState extends State { |
| @Override |
| public void enter() { |
| if (DBG) Log.d(TAG, getName() + "\n"); |
| EventLog.writeEvent(EVENTLOG_WIFI_STATE_CHANGED, getName()); |
| } |
| @Override |
| public boolean processMessage(Message message) { |
| if (DBG) Log.d(TAG, getName() + message.toString() + "\n"); |
| StateChangeResult stateChangeResult; |
| switch(message.what) { |
| case WifiMonitor.AUTHENTICATION_FAILURE_EVENT: |
| mSupplicantStateTracker.sendMessage(WifiMonitor.AUTHENTICATION_FAILURE_EVENT); |
| break; |
| case WifiMonitor.WPS_OVERLAP_EVENT: |
| /* We just need to broadcast the error */ |
| sendErrorBroadcast(WifiManager.WPS_OVERLAP_ERROR); |
| break; |
| case WifiMonitor.SUPPLICANT_STATE_CHANGE_EVENT: |
| handleSupplicantStateChange(message); |
| break; |
| /* Do a redundant disconnect without transition */ |
| case CMD_DISCONNECT: |
| WifiNative.disconnectCommand(); |
| break; |
| case CMD_RECONNECT: |
| WifiNative.reconnectCommand(); |
| break; |
| case CMD_REASSOCIATE: |
| WifiNative.reassociateCommand(); |
| break; |
| case CMD_CONNECT_NETWORK: |
| int netId = message.arg1; |
| WifiConfiguration config = (WifiConfiguration) message.obj; |
| |
| /* We connect to a specific network by issuing a select |
| * to the WifiConfigStore. This enables the network, |
| * while disabling all other networks in the supplicant. |
| * Disabling a connected network will cause a disconnection |
| * from the network. A reconnectCommand() will then initiate |
| * a connection to the enabled network. |
| */ |
| if (config != null) { |
| netId = WifiConfigStore.selectNetwork(config); |
| } else { |
| WifiConfigStore.selectNetwork(netId); |
| } |
| |
| /* The state tracker handles enabling networks upon completion/failure */ |
| mSupplicantStateTracker.sendMessage(CMD_CONNECT_NETWORK); |
| |
| WifiNative.reconnectCommand(); |
| mLastExplicitNetworkId = netId; |
| mLastNetworkChoiceTime = SystemClock.elapsedRealtime(); |
| mNextWifiActionExplicit = true; |
| Slog.d(TAG, "Setting wifi connect explicit for netid " + netId); |
| /* Expect a disconnection from the old connection */ |
| transitionTo(mDisconnectingState); |
| break; |
| case CMD_START_WPS: |
| mWpsStateMachine.sendMessage(Message.obtain(message)); |
| transitionTo(mWaitForWpsCompletionState); |
| break; |
| case WifiMonitor.SCAN_RESULTS_EVENT: |
| /* Set the scan setting back to "connect" mode */ |
| WifiNative.setScanResultHandlingCommand(CONNECT_MODE); |
| /* Handle scan results */ |
| return NOT_HANDLED; |
| case WifiMonitor.NETWORK_CONNECTION_EVENT: |
| Log.d(TAG,"Network connection established"); |
| mLastNetworkId = message.arg1; |
| mLastBssid = (String) message.obj; |
| |
| //TODO: make supplicant modification to push this in events |
| mWifiInfo.setSSID(fetchSSID()); |
| mWifiInfo.setBSSID(mLastBssid); |
| mWifiInfo.setNetworkId(mLastNetworkId); |
| if (mNextWifiActionExplicit && |
| mWifiInfo.getNetworkId() == mLastExplicitNetworkId && |
| SystemClock.elapsedRealtime() < mLastNetworkChoiceTime + |
| EXPLICIT_CONNECT_ALLOWED_DELAY_MS) { |
| mWifiInfo.setExplicitConnect(true); |
| } |
| mNextWifiActionExplicit = false; |
| /* send event to CM & network change broadcast */ |
| setNetworkDetailedState(DetailedState.OBTAINING_IPADDR); |
| sendNetworkStateChangeBroadcast(mLastBssid); |
| transitionTo(mConnectingState); |
| break; |
| case WifiMonitor.NETWORK_DISCONNECTION_EVENT: |
| Log.d(TAG,"Network connection lost"); |
| handleNetworkDisconnect(); |
| transitionTo(mDisconnectedState); |
| break; |
| default: |
| return NOT_HANDLED; |
| } |
| EventLog.writeEvent(EVENTLOG_WIFI_EVENT_HANDLED, message.what); |
| return HANDLED; |
| } |
| } |
| |
| class ConnectingState extends State { |
| |
| @Override |
| public void enter() { |
| if (DBG) Log.d(TAG, getName() + "\n"); |
| EventLog.writeEvent(EVENTLOG_WIFI_STATE_CHANGED, getName()); |
| |
| if (!WifiConfigStore.isUsingStaticIp(mLastNetworkId)) { |
| //start DHCP |
| mDhcpStateMachine = DhcpStateMachine.makeDhcpStateMachine( |
| mContext, WifiStateMachine.this, mInterfaceName); |
| mDhcpStateMachine.registerForPreDhcpNotification(); |
| mDhcpStateMachine.sendMessage(DhcpStateMachine.CMD_START_DHCP); |
| } else { |
| DhcpInfoInternal dhcpInfoInternal = WifiConfigStore.getIpConfiguration( |
| mLastNetworkId); |
| InterfaceConfiguration ifcg = new InterfaceConfiguration(); |
| ifcg.addr = dhcpInfoInternal.makeLinkAddress(); |
| ifcg.interfaceFlags = "[up]"; |
| try { |
| mNwService.setInterfaceConfig(mInterfaceName, ifcg); |
| Log.v(TAG, "Static IP configuration succeeded"); |
| sendMessage(CMD_STATIC_IP_SUCCESS, dhcpInfoInternal); |
| } catch (RemoteException re) { |
| Log.v(TAG, "Static IP configuration failed: " + re); |
| sendMessage(CMD_STATIC_IP_FAILURE); |
| } catch (IllegalStateException e) { |
| Log.v(TAG, "Static IP configuration failed: " + e); |
| sendMessage(CMD_STATIC_IP_FAILURE); |
| } |
| } |
| } |
| @Override |
| public boolean processMessage(Message message) { |
| if (DBG) Log.d(TAG, getName() + message.toString() + "\n"); |
| |
| switch(message.what) { |
| case DhcpStateMachine.CMD_PRE_DHCP_ACTION: |
| handlePreDhcpSetup(); |
| mDhcpStateMachine.sendMessage(DhcpStateMachine.CMD_PRE_DHCP_ACTION_COMPLETE); |
| break; |
| case DhcpStateMachine.CMD_POST_DHCP_ACTION: |
| handlePostDhcpSetup(); |
| if (message.arg1 == DhcpStateMachine.DHCP_SUCCESS) { |
| handleSuccessfulIpConfiguration((DhcpInfoInternal) message.obj); |
| transitionTo(mConnectedState); |
| } else if (message.arg1 == DhcpStateMachine.DHCP_FAILURE) { |
| handleFailedIpConfiguration(); |
| transitionTo(mDisconnectingState); |
| } |
| break; |
| case CMD_STATIC_IP_SUCCESS: |
| handleSuccessfulIpConfiguration((DhcpInfoInternal) message.obj); |
| transitionTo(mConnectedState); |
| break; |
| case CMD_STATIC_IP_FAILURE: |
| handleFailedIpConfiguration(); |
| transitionTo(mDisconnectingState); |
| break; |
| case CMD_DISCONNECT: |
| WifiNative.disconnectCommand(); |
| transitionTo(mDisconnectingState); |
| break; |
| /* Ignore connection to same network */ |
| case CMD_CONNECT_NETWORK: |
| int netId = message.arg1; |
| if (mWifiInfo.getNetworkId() == netId) { |
| break; |
| } |
| return NOT_HANDLED; |
| case CMD_SAVE_NETWORK: |
| deferMessage(message); |
| break; |
| /* Ignore */ |
| case WifiMonitor.NETWORK_CONNECTION_EVENT: |
| break; |
| case CMD_STOP_DRIVER: |
| sendMessage(CMD_DISCONNECT); |
| deferMessage(message); |
| break; |
| case CMD_SET_SCAN_MODE: |
| if (message.arg1 == SCAN_ONLY_MODE) { |
| sendMessage(CMD_DISCONNECT); |
| deferMessage(message); |
| } |
| break; |
| /* Defer scan when IP is being fetched */ |
| case CMD_START_SCAN: |
| deferMessage(message); |
| break; |
| /* Defer any power mode changes since we must keep active power mode at DHCP */ |
| case CMD_SET_HIGH_PERF_MODE: |
| deferMessage(message); |
| break; |
| default: |
| return NOT_HANDLED; |
| } |
| EventLog.writeEvent(EVENTLOG_WIFI_EVENT_HANDLED, message.what); |
| return HANDLED; |
| } |
| } |
| |
| class ConnectedState extends State { |
| @Override |
| public void enter() { |
| if (DBG) Log.d(TAG, getName() + "\n"); |
| EventLog.writeEvent(EVENTLOG_WIFI_STATE_CHANGED, getName()); |
| mRssiPollToken++; |
| if (mEnableRssiPolling) { |
| sendMessage(obtainMessage(WifiStateMachine.CMD_RSSI_POLL, mRssiPollToken, 0)); |
| } |
| } |
| @Override |
| public boolean processMessage(Message message) { |
| if (DBG) Log.d(TAG, getName() + message.toString() + "\n"); |
| boolean eventLoggingEnabled = true; |
| switch (message.what) { |
| case DhcpStateMachine.CMD_PRE_DHCP_ACTION: |
| handlePreDhcpSetup(); |
| mDhcpStateMachine.sendMessage(DhcpStateMachine.CMD_PRE_DHCP_ACTION_COMPLETE); |
| break; |
| case DhcpStateMachine.CMD_POST_DHCP_ACTION: |
| handlePostDhcpSetup(); |
| if (message.arg1 == DhcpStateMachine.DHCP_SUCCESS) { |
| handleSuccessfulIpConfiguration((DhcpInfoInternal) message.obj); |
| } else if (message.arg1 == DhcpStateMachine.DHCP_FAILURE) { |
| handleFailedIpConfiguration(); |
| transitionTo(mDisconnectingState); |
| } |
| break; |
| case CMD_DISCONNECT: |
| WifiNative.disconnectCommand(); |
| transitionTo(mDisconnectingState); |
| break; |
| case CMD_STOP_DRIVER: |
| sendMessage(CMD_DISCONNECT); |
| deferMessage(message); |
| break; |
| case CMD_REQUEST_CM_WAKELOCK: |
| checkAndSetConnectivityInstance(); |
| mCm.requestNetworkTransitionWakelock(TAG); |
| break; |
| case CMD_SET_SCAN_MODE: |
| if (message.arg1 == SCAN_ONLY_MODE) { |
| sendMessage(CMD_DISCONNECT); |
| deferMessage(message); |
| } |
| break; |
| case CMD_START_SCAN: |
| eventLoggingEnabled = false; |
| /* When the network is connected, re-scanning can trigger |
| * a reconnection. Put it in scan-only mode during scan. |
| * When scan results are received, the mode is switched |
| * back to CONNECT_MODE. |
| */ |
| WifiNative.setScanResultHandlingCommand(SCAN_ONLY_MODE); |
| /* Have the parent state handle the rest */ |
| return NOT_HANDLED; |
| /* Ignore connection to same network */ |
| case CMD_CONNECT_NETWORK: |
| int netId = message.arg1; |
| if (mWifiInfo.getNetworkId() == netId) { |
| break; |
| } |
| return NOT_HANDLED; |
| case CMD_SAVE_NETWORK: |
| WifiConfiguration config = (WifiConfiguration) message.obj; |
| NetworkUpdateResult result = WifiConfigStore.saveNetwork(config); |
| if (mWifiInfo.getNetworkId() == result.getNetworkId()) { |
| if (result.hasIpChanged()) { |
| Log.d(TAG,"Reconfiguring IP on connection"); |
| transitionTo(mConnectingState); |
| } |
| if (result.hasProxyChanged()) { |
| Log.d(TAG,"Reconfiguring proxy on connection"); |
| configureLinkProperties(); |
| sendLinkConfigurationChangedBroadcast(); |
| } |
| } |
| break; |
| /* Ignore */ |
| case WifiMonitor.NETWORK_CONNECTION_EVENT: |
| break; |
| case CMD_RSSI_POLL: |
| eventLoggingEnabled = false; |
| if (message.arg1 == mRssiPollToken) { |
| // Get Info and continue polling |
| fetchRssiAndLinkSpeedNative(); |
| sendMessageDelayed(obtainMessage(WifiStateMachine.CMD_RSSI_POLL, |
| mRssiPollToken, 0), POLL_RSSI_INTERVAL_MSECS); |
| } else { |
| // Polling has completed |
| } |
| break; |
| case CMD_ENABLE_RSSI_POLL: |
| mEnableRssiPolling = (message.arg1 == 1); |
| mRssiPollToken++; |
| if (mEnableRssiPolling) { |
| // first poll |
| fetchRssiAndLinkSpeedNative(); |
| sendMessageDelayed(obtainMessage(WifiStateMachine.CMD_RSSI_POLL, |
| mRssiPollToken, 0), POLL_RSSI_INTERVAL_MSECS); |
| } |
| break; |
| default: |
| return NOT_HANDLED; |
| } |
| if (eventLoggingEnabled) { |
| EventLog.writeEvent(EVENTLOG_WIFI_EVENT_HANDLED, message.what); |
| } |
| return HANDLED; |
| } |
| @Override |
| public void exit() { |
| /* If a scan result is pending in connected state, the supplicant |
| * is in SCAN_ONLY_MODE. Restore CONNECT_MODE on exit |
| */ |
| if (mScanResultIsPending) { |
| WifiNative.setScanResultHandlingCommand(CONNECT_MODE); |
| } |
| } |
| } |
| |
| class DisconnectingState extends State { |
| @Override |
| public void enter() { |
| if (DBG) Log.d(TAG, getName() + "\n"); |
| EventLog.writeEvent(EVENTLOG_WIFI_STATE_CHANGED, getName()); |
| } |
| @Override |
| public boolean processMessage(Message message) { |
| if (DBG) Log.d(TAG, getName() + message.toString() + "\n"); |
| switch (message.what) { |
| case CMD_STOP_DRIVER: /* Stop driver only after disconnect handled */ |
| deferMessage(message); |
| break; |
| case CMD_SET_SCAN_MODE: |
| if (message.arg1 == SCAN_ONLY_MODE) { |
| deferMessage(message); |
| } |
| break; |
| /* Handle in DisconnectedState */ |
| case WifiMonitor.SUPPLICANT_STATE_CHANGE_EVENT: |
| deferMessage(message); |
| break; |
| default: |
| return NOT_HANDLED; |
| } |
| EventLog.writeEvent(EVENTLOG_WIFI_EVENT_HANDLED, message.what); |
| return HANDLED; |
| } |
| } |
| |
| class DisconnectedState extends State { |
| private boolean mAlarmEnabled = false; |
| /* This is set from the overlay config file or from a secure setting. |
| * A value of 0 disables scanning in the framework. |
| */ |
| private long mFrameworkScanIntervalMs; |
| |
| private void setScanAlarm(boolean enabled) { |
| if (enabled == mAlarmEnabled) return; |
| if (enabled) { |
| if (mFrameworkScanIntervalMs > 0) { |
| mAlarmManager.setRepeating(AlarmManager.RTC_WAKEUP, |
| System.currentTimeMillis() + mFrameworkScanIntervalMs, |
| mFrameworkScanIntervalMs, |
| mScanIntent); |
| mAlarmEnabled = true; |
| } |
| } else { |
| mAlarmManager.cancel(mScanIntent); |
| mAlarmEnabled = false; |
| } |
| } |
| |
| @Override |
| public void enter() { |
| if (DBG) Log.d(TAG, getName() + "\n"); |
| EventLog.writeEvent(EVENTLOG_WIFI_STATE_CHANGED, getName()); |
| |
| mFrameworkScanIntervalMs = Settings.Secure.getLong(mContext.getContentResolver(), |
| Settings.Secure.WIFI_FRAMEWORK_SCAN_INTERVAL_MS, |
| mDefaultFrameworkScanIntervalMs); |
| /* |
| * We initiate background scanning if it is enabled, otherwise we |
| * initiate an infrequent scan that wakes up the device to ensure |
| * a user connects to an access point on the move |
| */ |
| if (mEnableBackgroundScan) { |
| /* If a regular scan result is pending, do not initiate background |
| * scan until the scan results are returned. This is needed because |
| * initiating a background scan will cancel the regular scan and |
| * scan results will not be returned until background scanning is |
| * cleared |
| */ |
| if (!mScanResultIsPending) { |
| WifiNative.enableBackgroundScanCommand(true); |
| } |
| } else { |
| setScanAlarm(true); |
| } |
| } |
| @Override |
| public boolean processMessage(Message message) { |
| if (DBG) Log.d(TAG, getName() + message.toString() + "\n"); |
| switch (message.what) { |
| case CMD_SET_SCAN_MODE: |
| if (message.arg1 == SCAN_ONLY_MODE) { |
| WifiNative.setScanResultHandlingCommand(message.arg1); |
| //Supplicant disconnect to prevent further connects |
| WifiNative.disconnectCommand(); |
| mIsScanMode = true; |
| transitionTo(mScanModeState); |
| } |
| break; |
| case CMD_ENABLE_BACKGROUND_SCAN: |
| mEnableBackgroundScan = (message.arg1 == 1); |
| if (mEnableBackgroundScan) { |
| WifiNative.enableBackgroundScanCommand(true); |
| setScanAlarm(false); |
| } else { |
| WifiNative.enableBackgroundScanCommand(false); |
| setScanAlarm(true); |
| } |
| break; |
| /* Ignore network disconnect */ |
| case WifiMonitor.NETWORK_DISCONNECTION_EVENT: |
| break; |
| case WifiMonitor.SUPPLICANT_STATE_CHANGE_EVENT: |
| StateChangeResult stateChangeResult = (StateChangeResult) message.obj; |
| setNetworkDetailedState(WifiInfo.getDetailedStateOf(stateChangeResult.state)); |
| /* ConnectModeState does the rest of the handling */ |
| return NOT_HANDLED; |
| case CMD_START_SCAN: |
| /* Disable background scan temporarily during a regular scan */ |
| if (mEnableBackgroundScan) { |
| WifiNative.enableBackgroundScanCommand(false); |
| } |
| /* Handled in parent state */ |
| return NOT_HANDLED; |
| case WifiMonitor.SCAN_RESULTS_EVENT: |
| /* Re-enable background scan when a pending scan result is received */ |
| if (mEnableBackgroundScan && mScanResultIsPending) { |
| WifiNative.enableBackgroundScanCommand(true); |
| } |
| /* Handled in parent state */ |
| return NOT_HANDLED; |
| default: |
| return NOT_HANDLED; |
| } |
| EventLog.writeEvent(EVENTLOG_WIFI_EVENT_HANDLED, message.what); |
| return HANDLED; |
| } |
| |
| @Override |
| public void exit() { |
| /* No need for a background scan upon exit from a disconnected state */ |
| if (mEnableBackgroundScan) { |
| WifiNative.enableBackgroundScanCommand(false); |
| } |
| setScanAlarm(false); |
| } |
| } |
| |
| class WaitForWpsCompletionState extends State { |
| @Override |
| public void enter() { |
| if (DBG) Log.d(TAG, getName() + "\n"); |
| EventLog.writeEvent(EVENTLOG_WIFI_STATE_CHANGED, getName()); |
| } |
| @Override |
| public boolean processMessage(Message message) { |
| if (DBG) Log.d(TAG, getName() + message.toString() + "\n"); |
| switch (message.what) { |
| /* Defer all commands that can cause connections to a different network |
| * or put the state machine out of connect mode |
| */ |
| case CMD_STOP_DRIVER: |
| case CMD_SET_SCAN_MODE: |
| case CMD_CONNECT_NETWORK: |
| case CMD_ENABLE_NETWORK: |
| case CMD_RECONNECT: |
| case CMD_REASSOCIATE: |
| case WifiMonitor.NETWORK_CONNECTION_EVENT: /* Handled after IP & proxy update */ |
| deferMessage(message); |
| break; |
| case WifiMonitor.NETWORK_DISCONNECTION_EVENT: |
| Log.d(TAG,"Network connection lost"); |
| handleNetworkDisconnect(); |
| break; |
| case WPS_COMPLETED_EVENT: |
| /* we are still disconnected until we see a network connection |
| * notification */ |
| transitionTo(mDisconnectedState); |
| break; |
| default: |
| return NOT_HANDLED; |
| } |
| EventLog.writeEvent(EVENTLOG_WIFI_EVENT_HANDLED, message.what); |
| return HANDLED; |
| } |
| } |
| |
| class SoftApStartingState extends State { |
| @Override |
| public void enter() { |
| if (DBG) Log.d(TAG, getName() + "\n"); |
| EventLog.writeEvent(EVENTLOG_WIFI_STATE_CHANGED, getName()); |
| |
| final Message message = Message.obtain(getCurrentMessage()); |
| final WifiConfiguration config = (WifiConfiguration) message.obj; |
| |
| // start hostapd on a seperate thread |
| new Thread(new Runnable() { |
| public void run() { |
| if (startSoftApWithConfig(config)) { |
| Log.d(TAG, "Soft AP start successful"); |
| sendMessage(CMD_START_AP_SUCCESS); |
| } else { |
| Log.d(TAG, "Soft AP start failed"); |
| sendMessage(CMD_START_AP_FAILURE); |
| } |
| } |
| }).start(); |
| } |
| @Override |
| public boolean processMessage(Message message) { |
| if (DBG) Log.d(TAG, getName() + message.toString() + "\n"); |
| switch(message.what) { |
| case CMD_LOAD_DRIVER: |
| case CMD_UNLOAD_DRIVER: |
| case CMD_START_SUPPLICANT: |
| case CMD_STOP_SUPPLICANT: |
| case CMD_START_AP: |
| case CMD_STOP_AP: |
| case CMD_START_DRIVER: |
| case CMD_STOP_DRIVER: |
| case CMD_SET_SCAN_MODE: |
| case CMD_SET_SCAN_TYPE: |
| case CMD_SET_HIGH_PERF_MODE: |
| case CMD_SET_COUNTRY_CODE: |
| case CMD_SET_FREQUENCY_BAND: |
| case CMD_START_PACKET_FILTERING: |
| case CMD_STOP_PACKET_FILTERING: |
| case CMD_TETHER_INTERFACE: |
| case WifiP2pService.P2P_ENABLE_PENDING: |
| deferMessage(message); |
| break; |
| case CMD_START_AP_SUCCESS: |
| setWifiApState(WIFI_AP_STATE_ENABLED); |
| transitionTo(mSoftApStartedState); |
| break; |
| case CMD_START_AP_FAILURE: |
| // initiate driver unload |
| sendMessage(obtainMessage(CMD_UNLOAD_DRIVER, WIFI_AP_STATE_FAILED, 0)); |
| break; |
| default: |
| return NOT_HANDLED; |
| } |
| EventLog.writeEvent(EVENTLOG_WIFI_EVENT_HANDLED, message.what); |
| return HANDLED; |
| } |
| } |
| |
| class SoftApStartedState extends State { |
| @Override |
| public void enter() { |
| if (DBG) Log.d(TAG, getName() + "\n"); |
| EventLog.writeEvent(EVENTLOG_WIFI_STATE_CHANGED, getName()); |
| } |
| @Override |
| public boolean processMessage(Message message) { |
| if (DBG) Log.d(TAG, getName() + message.toString() + "\n"); |
| switch(message.what) { |
| case CMD_STOP_AP: |
| Log.d(TAG,"Stopping Soft AP"); |
| setWifiApState(WIFI_AP_STATE_DISABLING); |
| stopTethering(); |
| try { |
| mNwService.stopAccessPoint(mInterfaceName); |
| } catch(Exception e) { |
| Log.e(TAG, "Exception in stopAccessPoint()"); |
| } |
| transitionTo(mDriverLoadedState); |
| break; |
| case CMD_START_AP: |
| // Ignore a start on a running access point |
| break; |
| /* Fail client mode operation when soft AP is enabled */ |
| case CMD_START_SUPPLICANT: |
| Log.e(TAG,"Cannot start supplicant with a running soft AP"); |
| setWifiState(WIFI_STATE_UNKNOWN); |
| break; |
| case CMD_TETHER_INTERFACE: |
| ArrayList<String> available = (ArrayList<String>) message.obj; |
| if (startTethering(available)) { |
| transitionTo(mTetheredState); |
| } |
| break; |
| case WifiP2pService.P2P_ENABLE_PENDING: |
| // turn of soft Ap and defer to be handled in DriverUnloadedState |
| setWifiApEnabled(null, false); |
| deferMessage(message); |
| break; |
| default: |
| return NOT_HANDLED; |
| } |
| EventLog.writeEvent(EVENTLOG_WIFI_EVENT_HANDLED, message.what); |
| return HANDLED; |
| } |
| } |
| |
| class WaitForP2pDisableState extends State { |
| private int mSavedArg; |
| @Override |
| public void enter() { |
| if (DBG) Log.d(TAG, getName() + "\n"); |
| EventLog.writeEvent(EVENTLOG_WIFI_STATE_CHANGED, getName()); |
| |
| //Preserve the argument arg1 that has information used in DriverLoadingState |
| mSavedArg = getCurrentMessage().arg1; |
| } |
| @Override |
| public boolean processMessage(Message message) { |
| if (DBG) Log.d(TAG, getName() + message.toString() + "\n"); |
| switch(message.what) { |
| case WifiP2pService.WIFI_ENABLE_PROCEED: |
| //restore argument from original message (CMD_LOAD_DRIVER) |
| message.arg1 = mSavedArg; |
| transitionTo(mDriverLoadingState); |
| break; |
| case CMD_LOAD_DRIVER: |
| case CMD_UNLOAD_DRIVER: |
| case CMD_START_SUPPLICANT: |
| case CMD_STOP_SUPPLICANT: |
| case CMD_START_AP: |
| case CMD_STOP_AP: |
| case CMD_START_DRIVER: |
| case CMD_STOP_DRIVER: |
| case CMD_SET_SCAN_MODE: |
| case CMD_SET_SCAN_TYPE: |
| case CMD_SET_HIGH_PERF_MODE: |
| case CMD_SET_COUNTRY_CODE: |
| case CMD_SET_FREQUENCY_BAND: |
| case CMD_START_PACKET_FILTERING: |
| case CMD_STOP_PACKET_FILTERING: |
| deferMessage(message); |
| break; |
| default: |
| return NOT_HANDLED; |
| } |
| EventLog.writeEvent(EVENTLOG_WIFI_EVENT_HANDLED, message.what); |
| return HANDLED; |
| } |
| } |
| |
| class TetheredState extends State { |
| @Override |
| public void enter() { |
| if (DBG) Log.d(TAG, getName() + "\n"); |
| EventLog.writeEvent(EVENTLOG_WIFI_STATE_CHANGED, getName()); |
| } |
| @Override |
| public boolean processMessage(Message message) { |
| if (DBG) Log.d(TAG, getName() + message.toString() + "\n"); |
| switch(message.what) { |
| case CMD_TETHER_INTERFACE: |
| // Ignore any duplicate interface available notifications |
| // when in tethered state |
| return HANDLED; |
| default: |
| return NOT_HANDLED; |
| } |
| } |
| } |
| } |