| /* |
| * Qualcomm Atheros OUI and vendor specific assignments |
| * Copyright (c) 2014-2017, Qualcomm Atheros, Inc. |
| * Copyright (c) 2018-2020, The Linux Foundation |
| * Copyright (c) 2021-2023, Qualcomm Innovation Center, Inc. |
| * |
| * This software may be distributed under the terms of the BSD license. |
| * See README for more details. |
| */ |
| |
| #ifndef QCA_VENDOR_H |
| #define QCA_VENDOR_H |
| |
| /* |
| * This file is a registry of identifier assignments from the Qualcomm Atheros |
| * OUI 00:13:74 for purposes other than MAC address assignment. New identifiers |
| * can be assigned through normal review process for changes to the upstream |
| * hostap.git repository. |
| */ |
| |
| #define OUI_QCA 0x001374 |
| |
| #ifndef BIT |
| #define BIT(x) (1U << (x)) |
| #endif |
| |
| /** |
| * enum qca_radiotap_vendor_ids - QCA radiotap vendor namespace IDs |
| */ |
| enum qca_radiotap_vendor_ids { |
| QCA_RADIOTAP_VID_WLANTEST = 0, |
| }; |
| |
| /** |
| * enum qca_nl80211_vendor_subcmds - QCA nl80211 vendor command identifiers |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_UNSPEC: Reserved value 0 |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_TEST: Test command/event |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_ROAMING: Set roaming policy for drivers that use |
| * internal BSS-selection. This command uses |
| * @QCA_WLAN_VENDOR_ATTR_ROAMING_POLICY to specify the new roaming policy |
| * for the current connection (i.e., changes policy set by the nl80211 |
| * Connect command). @QCA_WLAN_VENDOR_ATTR_MAC_ADDR may optionally be |
| * included to indicate which BSS to use in case roaming is disabled. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY: Recommendation of frequency |
| * ranges to avoid to reduce issues due to interference or internal |
| * co-existence information in the driver. These frequencies aim to |
| * minimize the traffic but not to totally avoid the traffic. That said |
| * for a P2P use case, these frequencies are allowed for the P2P |
| * discovery/negotiation but avoid the group to get formed on these |
| * frequencies. The event data structure is defined in |
| * struct qca_avoid_freq_list. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_DFS_CAPABILITY: Command to check driver support |
| * for DFS offloading. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_NAN: NAN command/event which is used to pass |
| * NAN Request/Response and NAN Indication messages. These messages are |
| * interpreted between the framework and the firmware component. While |
| * sending the command from userspace to the driver, payload is not |
| * encapsulated inside any attribute. Attribute QCA_WLAN_VENDOR_ATTR_NAN |
| * is used when receiving vendor events in userspace from the driver. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_SET_KEY: Set key operation that can be |
| * used to configure PMK to the driver even when not connected. This can |
| * be used to request offloading of key management operations. Only used |
| * if device supports QCA_WLAN_VENDOR_FEATURE_KEY_MGMT_OFFLOAD. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH: An extended version of |
| * NL80211_CMD_ROAM event with optional attributes including information |
| * from offloaded key management operation. Uses |
| * enum qca_wlan_vendor_attr_roam_auth attributes. Only used |
| * if device supports QCA_WLAN_VENDOR_FEATURE_KEY_MGMT_OFFLOAD. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_DO_ACS: ACS command/event which is used to |
| * invoke the ACS function in device and pass selected channels to |
| * hostapd. Uses enum qca_wlan_vendor_attr_acs_offload attributes. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES: Command to get the features |
| * supported by the driver. enum qca_wlan_vendor_features defines |
| * the possible features. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_STARTED: Event used by driver, |
| * which supports DFS offloading, to indicate a channel availability check |
| * start. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_FINISHED: Event used by driver, |
| * which supports DFS offloading, to indicate a channel availability check |
| * completion. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_ABORTED: Event used by driver, |
| * which supports DFS offloading, to indicate that the channel availability |
| * check aborted, no change to the channel status. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_NOP_FINISHED: Event used by |
| * driver, which supports DFS offloading, to indicate that the |
| * Non-Occupancy Period for this channel is over, channel becomes usable. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_RADAR_DETECTED: Event used by driver, |
| * which supports DFS offloading, to indicate a radar pattern has been |
| * detected. The channel is now unusable. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_INFO: Get information from the driver. |
| * Attributes defined in enum qca_wlan_vendor_attr_get_wifi_info. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_GET_LOGGER_FEATURE_SET: Get the feature bitmap |
| * based on enum wifi_logger_supported_features. Attributes defined in |
| * enum qca_wlan_vendor_attr_get_logger_features. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_GET_RING_DATA: Get the ring data from a particular |
| * logger ring, QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_RING_ID is passed as the |
| * attribute for this command. Attributes defined in |
| * enum qca_wlan_vendor_attr_wifi_logger_start. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_CAPABILITIES: Get the supported TDLS |
| * capabilities of the driver, parameters includes the attributes defined |
| * in enum qca_wlan_vendor_attr_tdls_get_capabilities. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_OFFLOADED_PACKETS: Vendor command used to offload |
| * sending of certain periodic IP packet to firmware, attributes defined in |
| * enum qca_wlan_vendor_attr_offloaded_packets. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_MONITOR_RSSI: Command used to configure RSSI |
| * monitoring, defines min and max RSSI which are configured for RSSI |
| * monitoring. Also used to notify the RSSI breach and provides the BSSID |
| * and RSSI value that was breached. Attributes defined in |
| * enum qca_wlan_vendor_attr_rssi_monitoring. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_NDP: Command used for performing various NAN |
| * Data Path (NDP) related operations, attributes defined in |
| * enum qca_wlan_vendor_attr_ndp_params. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_ND_OFFLOAD: Command used to enable/disable |
| * Neighbour Discovery offload, attributes defined in |
| * enum qca_wlan_vendor_attr_nd_offload. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_PACKET_FILTER: Used to set/get the various |
| * configuration parameter for BPF packet filter, attributes defined in |
| * enum qca_wlan_vendor_attr_packet_filter. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_GET_BUS_SIZE: Gets the driver-firmware |
| * maximum supported size, attributes defined in |
| * enum qca_wlan_vendor_drv_info. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_GET_WAKE_REASON_STATS: Command to get various |
| * data about wake reasons and datapath IP statistics, attributes defined |
| * in enum qca_wlan_vendor_attr_wake_stats. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_OCB_SET_CONFIG: Command used to set configuration |
| * for IEEE 802.11 communicating outside the context of a basic service |
| * set, called OCB command. Uses the attributes defines in |
| * enum qca_wlan_vendor_attr_ocb_set_config. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_OCB_SET_UTC_TIME: Command used to set OCB |
| * UTC time. Use the attributes defines in |
| * enum qca_wlan_vendor_attr_ocb_set_utc_time. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_OCB_START_TIMING_ADVERT: Command used to start |
| * sending OCB timing advert frames. Uses the attributes defines in |
| * enum qca_wlan_vendor_attr_ocb_start_timing_advert. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_OCB_STOP_TIMING_ADVERT: Command used to stop |
| * OCB timing advert. Uses the attributes defines in |
| * enum qca_wlan_vendor_attr_ocb_stop_timing_advert. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_OCB_GET_TSF_TIMER: Command used to get TSF |
| * timer value. Uses the attributes defines in |
| * enum qca_wlan_vendor_attr_ocb_get_tsf_resp. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_LINK_PROPERTIES: Command/event to update the |
| * link properties of the respective interface. As an event, is used |
| * to notify the connected station's status. The attributes for this |
| * command are defined in enum qca_wlan_vendor_attr_link_properties. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_SETBAND: Command to configure the enabled band(s) |
| * to the driver. This command sets the band(s) through either the |
| * attribute QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE or |
| * QCA_WLAN_VENDOR_ATTR_SETBAND_MASK (or both). |
| * QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE refers enum qca_set_band as unsigned |
| * integer values and QCA_WLAN_VENDOR_ATTR_SETBAND_MASK refers it as 32 |
| * bit unsigned bitmask values. The allowed values for |
| * QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE are limited to QCA_SETBAND_AUTO, |
| * QCA_SETBAND_5G, and QCA_SETBAND_2G. Other values/bitmasks are valid for |
| * QCA_WLAN_VENDOR_ATTR_SETBAND_MASK. The attribute |
| * QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE is deprecated and the recommendation |
| * is to use the QCA_WLAN_VENDOR_ATTR_SETBAND_MASK. If the both attributes |
| * are included for backwards compatibility, the configurations through |
| * QCA_WLAN_VENDOR_ATTR_SETBAND_MASK will take the precedence with drivers |
| * that support both attributes. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_ACS_POLICY: This command is used to configure |
| * DFS policy and channel hint for ACS operation. This command uses the |
| * attributes defined in enum qca_wlan_vendor_attr_acs_config and |
| * enum qca_acs_dfs_mode. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_START: Command used to |
| * start the P2P Listen offload function in device and pass the listen |
| * channel, period, interval, count, device types, and vendor specific |
| * information elements to the device driver and firmware. |
| * Uses the attributes defines in |
| * enum qca_wlan_vendor_attr_p2p_listen_offload. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_STOP: Command/event used to |
| * indicate stop request/response of the P2P Listen offload function in |
| * device. As an event, it indicates either the feature stopped after it |
| * was already running or feature has actually failed to start. Uses the |
| * attributes defines in enum qca_wlan_vendor_attr_p2p_listen_offload. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_SAP_CONDITIONAL_CHAN_SWITCH: After AP starts |
| * beaconing, this sub command provides the driver, the frequencies on the |
| * 5 GHz band to check for any radar activity. Driver selects one channel |
| * from this priority list provided through |
| * @QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_FREQ_LIST and starts |
| * to check for radar activity on it. If no radar activity is detected |
| * during the channel availability check period, driver internally switches |
| * to the selected frequency of operation. If the frequency is zero, driver |
| * internally selects a channel. The status of this conditional switch is |
| * indicated through an event using the same sub command through |
| * @QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_STATUS. Attributes are |
| * listed in qca_wlan_vendor_attr_sap_conditional_chan_switch. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_GPIO_CONFIG_COMMAND: Set GPIO pins. This uses the |
| * attributes defined in enum qca_wlan_gpio_attr. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_GET_HW_CAPABILITY: Fetch hardware capabilities. |
| * This uses @QCA_WLAN_VENDOR_ATTR_GET_HW_CAPABILITY to indicate which |
| * capabilities are to be fetched and other |
| * enum qca_wlan_vendor_attr_get_hw_capability attributes to return the |
| * requested capabilities. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_LL_STATS_EXT: Link layer statistics extension. |
| * enum qca_wlan_vendor_attr_ll_stats_ext attributes are used with this |
| * command and event. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_LOC_GET_CAPA: Get capabilities for |
| * indoor location features. Capabilities are reported in |
| * QCA_WLAN_VENDOR_ATTR_LOC_CAPA. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION: Start an FTM |
| * (fine timing measurement) session with one or more peers. |
| * Specify Session cookie in QCA_WLAN_VENDOR_ATTR_FTM_SESSION_COOKIE and |
| * peer information in QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PEERS. |
| * On success, 0 or more QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT |
| * events will be reported, followed by |
| * QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE event to indicate |
| * end of session. |
| * Refer to IEEE P802.11-REVmc/D7.0, 11.24.6 |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_FTM_ABORT_SESSION: Abort a running session. |
| * A QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE will be reported with |
| * status code indicating session was aborted. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT: Event with measurement |
| * results for one peer. Results are reported in |
| * QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PEER_RESULTS. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE: Event triggered when |
| * FTM session is finished, either successfully or aborted by |
| * request. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER: Configure FTM responder |
| * mode. QCA_WLAN_VENDOR_ATTR_FTM_RESPONDER_ENABLE specifies whether |
| * to enable or disable the responder. LCI/LCR reports can be |
| * configured with QCA_WLAN_VENDOR_ATTR_FTM_LCI and |
| * QCA_WLAN_VENDOR_ATTR_FTM_LCR. Can be called multiple |
| * times to update the LCI/LCR reports. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS: Perform a standalone AOA (angle of |
| * arrival) measurement with a single peer. Specify peer MAC address in |
| * QCA_WLAN_VENDOR_ATTR_MAC_ADDR and optionally frequency (MHz) in |
| * QCA_WLAN_VENDOR_ATTR_FREQ (if not specified, locate peer in kernel |
| * scan results cache and use the frequency from there). |
| * Also specify measurement type in QCA_WLAN_VENDOR_ATTR_AOA_TYPE. |
| * Measurement result is reported in |
| * QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT event. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_AOA_ABORT_MEAS: Abort an AOA measurement. Specify |
| * peer MAC address in QCA_WLAN_VENDOR_ATTR_MAC_ADDR. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT: Event that reports |
| * the AOA measurement result. |
| * Peer MAC address reported in QCA_WLAN_VENDOR_ATTR_MAC_ADDR. |
| * success/failure status is reported in |
| * QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS. |
| * Measurement data is reported in QCA_WLAN_VENDOR_ATTR_AOA_MEAS_RESULT. |
| * The antenna array(s) used in the measurement are reported in |
| * QCA_WLAN_VENDOR_ATTR_LOC_ANTENNA_ARRAY_MASK. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_ENCRYPTION_TEST: Encrypt/decrypt the given |
| * data as per the given parameters. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI: Get antenna RSSI value for a |
| * specific chain. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SECTOR_CFG: Get low level |
| * configuration for a DMG RF sector. Specify sector index in |
| * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX, sector type in |
| * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE and RF modules |
| * to return sector information for in |
| * QCA_WLAN_VENDOR_ATTR_DMG_RF_MODULE_MASK. Returns sector configuration |
| * in QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG. Also return the |
| * exact time where information was captured in |
| * QCA_WLAN_VENDOR_ATTR_TSF. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SECTOR_CFG: Set low level |
| * configuration for a DMG RF sector. Specify sector index in |
| * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX, sector type in |
| * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE and sector configuration |
| * for one or more DMG RF modules in |
| * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SELECTED_SECTOR: Get selected |
| * DMG RF sector for a station. This is the sector that the HW |
| * will use to communicate with the station. Specify the MAC address |
| * of associated station/AP/PCP in QCA_WLAN_VENDOR_ATTR_MAC_ADDR (not |
| * needed for unassociated station). Specify sector type to return in |
| * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE. Returns the selected |
| * sector index in QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX. |
| * Also return the exact time where the information was captured |
| * in QCA_WLAN_VENDOR_ATTR_TSF. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SELECTED_SECTOR: Set the |
| * selected DMG RF sector for a station. This is the sector that |
| * the HW will use to communicate with the station. |
| * Specify the MAC address of associated station/AP/PCP in |
| * QCA_WLAN_VENDOR_ATTR_MAC_ADDR, the sector type to select in |
| * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE and the sector index |
| * in QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX. |
| * The selected sector will be locked such that it will not be |
| * modified like it normally does (for example when station |
| * moves around). To unlock the selected sector for a station |
| * pass the special value 0xFFFF in the sector index. To unlock |
| * all connected stations also pass a broadcast MAC address. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_CONFIGURE_TDLS: Configure the TDLS behavior |
| * in the host driver. The different TDLS configurations are defined |
| * by the attributes in enum qca_wlan_vendor_attr_tdls_configuration. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_GET_HE_CAPABILITIES: Query device IEEE 802.11ax HE |
| * capabilities. The response uses the attributes defined in |
| * enum qca_wlan_vendor_attr_get_he_capabilities. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_ABORT_SCAN: Abort an ongoing vendor scan that was |
| * started with QCA_NL80211_VENDOR_SUBCMD_TRIGGER_SCAN. This command |
| * carries the scan cookie of the corresponding scan request. The scan |
| * cookie is represented by QCA_WLAN_VENDOR_ATTR_SCAN_COOKIE. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS: Set the Specific |
| * Absorption Rate (SAR) power limits. A critical regulation for |
| * FCC compliance, OEMs require methods to set SAR limits on TX |
| * power of WLAN/WWAN. enum qca_vendor_attr_sar_limits |
| * attributes are used with this command. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS: This command/event is used by the |
| * host driver for offloading the implementation of Auto Channel Selection |
| * (ACS) to an external user space entity. This interface is used as the |
| * event from the host driver to the user space entity and also as the |
| * request from the user space entity to the host driver. The event from |
| * the host driver is used by the user space entity as an indication to |
| * start the ACS functionality. The attributes used by this event are |
| * represented by the enum qca_wlan_vendor_attr_external_acs_event. |
| * User space entity uses the same interface to inform the host driver with |
| * selected channels after the ACS operation using the attributes defined |
| * by enum qca_wlan_vendor_attr_external_acs_channels. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_CHIP_PWRSAVE_FAILURE: Vendor event carrying the |
| * requisite information leading to a power save failure. The information |
| * carried as part of this event is represented by the |
| * enum qca_attr_chip_power_save_failure attributes. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_SET: Start/Stop the NUD statistics |
| * collection. Uses attributes defined in enum qca_attr_nud_stats_set. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_GET: Get the NUD statistics. These |
| * statistics are represented by the enum qca_attr_nud_stats_get |
| * attributes. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_FETCH_BSS_TRANSITION_STATUS: Sub-command to fetch |
| * the BSS transition status, whether accept or reject, for a list of |
| * candidate BSSIDs provided by the userspace. This uses the vendor |
| * attributes QCA_WLAN_VENDOR_ATTR_BTM_MBO_TRANSITION_REASON and |
| * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO. The userspace shall specify |
| * the attributes QCA_WLAN_VENDOR_ATTR_BTM_MBO_TRANSITION_REASON and an |
| * array of QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_BSSID nested in |
| * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO in the request. In the response |
| * the driver shall specify array of |
| * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_BSSID and |
| * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_STATUS pairs nested in |
| * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_SET_TRACE_LEVEL: Set the trace level for a |
| * specific QCA module. The trace levels are represented by |
| * enum qca_attr_trace_level attributes. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT: Set the Beam Refinement |
| * Protocol antenna limit in different modes. See enum |
| * qca_wlan_vendor_attr_brp_ant_limit_mode. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START: Start spectral scan. The scan |
| * parameters are specified by enum qca_wlan_vendor_attr_spectral_scan. |
| * This returns a cookie (%QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_COOKIE) |
| * identifying the operation in success case. In failure cases an |
| * error code (%QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_ERROR_CODE) |
| * describing the reason for the failure is returned. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_STOP: Stop spectral scan. This uses |
| * a cookie (%QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_COOKIE) from |
| * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START to identify the scan to |
| * be stopped. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_ACTIVE_TOS: Set the active Type Of Service on the |
| * specific interface. This can be used to modify some of the low level |
| * scan parameters (off channel dwell time, home channel time) in the |
| * driver/firmware. These parameters are maintained within the host driver. |
| * This command is valid only when the interface is in the connected state. |
| * These scan parameters shall be reset by the driver/firmware once |
| * disconnected. The attributes used with this command are defined in |
| * enum qca_wlan_vendor_attr_active_tos. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_HANG: Event indicating to the user space that the |
| * driver has detected an internal failure. This event carries the |
| * information indicating the reason that triggered this detection. The |
| * attributes for this command are defined in |
| * enum qca_wlan_vendor_attr_hang. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CONFIG: Get the current values |
| * of spectral parameters used. The spectral scan parameters are specified |
| * by enum qca_wlan_vendor_attr_spectral_scan. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_DIAG_STATS: Get the debug stats |
| * for spectral scan functionality. The debug stats are specified by |
| * enum qca_wlan_vendor_attr_spectral_diag_stats. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO: Get spectral |
| * scan system capabilities. The capabilities are specified |
| * by enum qca_wlan_vendor_attr_spectral_cap. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_STATUS: Get the current |
| * status of spectral scan. The status values are specified |
| * by enum qca_wlan_vendor_attr_spectral_scan_status. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_PEER_FLUSH_PENDING: Sub-command to flush |
| * peer pending packets. Specify the peer MAC address in |
| * QCA_WLAN_VENDOR_ATTR_PEER_ADDR and the access category of the packets |
| * in QCA_WLAN_VENDOR_ATTR_AC. The attributes are listed |
| * in enum qca_wlan_vendor_attr_flush_pending. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_GET_RROP_INFO: Get vendor specific Representative |
| * RF Operating Parameter (RROP) information. The attributes for this |
| * information are defined in enum qca_wlan_vendor_attr_rrop_info. This is |
| * intended for use by external Auto Channel Selection applications. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS: Get the Specific Absorption Rate |
| * (SAR) power limits. This is a companion to the command |
| * @QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS and is used to retrieve the |
| * settings currently in use. The attributes returned by this command are |
| * defined by enum qca_vendor_attr_sar_limits. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_WLAN_MAC_INFO: Provides the current behavior of |
| * the WLAN hardware MAC. Also, provides the WLAN netdev interface |
| * information attached to the respective MAC. |
| * This works both as a query (user space asks the current mode) or event |
| * interface (driver advertising the current mode to the user space). |
| * Driver does not trigger this event for temporary hardware mode changes. |
| * Mode changes w.r.t Wi-Fi connection update (VIZ creation / deletion, |
| * channel change, etc.) are updated with this event. Attributes for this |
| * interface are defined in enum qca_wlan_vendor_attr_mac. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_SET_QDEPTH_THRESH: Set MSDU queue depth threshold |
| * per peer per TID. Attributes for this command are define in |
| * enum qca_wlan_set_qdepth_thresh_attr. |
| * @QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD: Provides the thermal shutdown action |
| * guide for WLAN driver. Request to suspend of driver and FW if the |
| * temperature is higher than the suspend threshold; resume action is |
| * requested to driver if the temperature is lower than the resume |
| * threshold. In user poll mode, request temperature data by user. For test |
| * purpose, getting thermal shutdown configuration parameters is needed. |
| * Attributes for this interface are defined in |
| * enum qca_wlan_vendor_attr_thermal_cmd. |
| * @QCA_NL80211_VENDOR_SUBCMD_THERMAL_EVENT: Thermal events reported from |
| * driver. Thermal temperature and indication of resume completion are |
| * reported as thermal events. The attributes for this command are defined |
| * in enum qca_wlan_vendor_attr_thermal_event. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION: Sub command to set WiFi |
| * test configuration. Attributes for this command are defined in |
| * enum qca_wlan_vendor_attr_wifi_test_config. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER: This command is used to configure an |
| * RX filter to receive frames from stations that are active on the |
| * operating channel, but not associated with the local device (e.g., STAs |
| * associated with other APs). Filtering is done based on a list of BSSIDs |
| * and STA MAC addresses added by the user. This command is also used to |
| * fetch the statistics of unassociated stations. The attributes used with |
| * this command are defined in enum qca_wlan_vendor_attr_bss_filter. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_NAN_EXT: An extendable version of NAN vendor |
| * command. The earlier command for NAN, QCA_NL80211_VENDOR_SUBCMD_NAN, |
| * carried a payload which was a binary blob of data. The command was not |
| * extendable to send more information. The newer version carries the |
| * legacy blob encapsulated within an attribute and can be extended with |
| * additional vendor attributes that can enhance the NAN command interface. |
| * @QCA_NL80211_VENDOR_SUBCMD_ROAM_SCAN_EVENT: Event to indicate scan triggered |
| * or stopped within driver/firmware in order to initiate roaming. The |
| * attributes used with this event are defined in enum |
| * qca_wlan_vendor_attr_roam_scan. Some drivers may not send these events |
| * in few cases, e.g., if the host processor is sleeping when this event |
| * is generated in firmware. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_PEER_CFR_CAPTURE_CFG: This command is used to |
| * configure parameters per peer to capture Channel Frequency Response |
| * (CFR) and enable Periodic CFR capture. The attributes for this command |
| * are defined in enum qca_wlan_vendor_peer_cfr_capture_attr. This command |
| * can also be used to send CFR data from the driver to userspace when |
| * netlink events are used to send CFR data. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_THROUGHPUT_CHANGE_EVENT: Event to indicate changes |
| * in throughput dynamically. The driver estimates the throughput based on |
| * number of packets being transmitted/received per second and indicates |
| * the changes in throughput to user space. Userspace tools can use this |
| * information to configure kernel's TCP parameters in order to achieve |
| * peak throughput. Optionally, the driver will also send guidance on |
| * modifications to kernel's TCP parameters which can be referred by |
| * userspace tools. The attributes used with this event are defined in enum |
| * qca_wlan_vendor_attr_throughput_change. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_COEX_CONFIG: This command is used to set |
| * priorities among different types of traffic during coex scenarios. |
| * Current supported prioritization is among WLAN/BT/ZIGBEE with different |
| * profiles mentioned in enum qca_coex_config_profiles. The associated |
| * attributes used with this command are defined in enum |
| * qca_vendor_attr_coex_config. |
| * |
| * Based on the config provided, FW will boost the weight and prioritize |
| * the traffic for that subsystem (WLAN/BT/Zigbee). |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_GET_SUPPORTED_AKMS: This command is used to query |
| * the supported AKM suite selectorss from the driver. It returns the list |
| * of supported AKMs in the attribute NL80211_ATTR_AKM_SUITES. |
| * @QCA_NL80211_VENDOR_SUBCMD_GET_FW_STATE: This command is used to get firmware |
| * state from the driver. It returns the firmware state in the attribute |
| * QCA_WLAN_VENDOR_ATTR_FW_STATE. |
| * @QCA_NL80211_VENDOR_SUBCMD_PEER_STATS_CACHE_FLUSH: This vendor subcommand |
| * is used by the driver to flush per-peer cached statistics to user space |
| * application. This interface is used as an event from the driver to |
| * user space application. Attributes for this event are specified in |
| * enum qca_wlan_vendor_attr_peer_stats_cache_params. |
| * QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_DATA attribute is expected to be |
| * sent in the event. |
| * @QCA_NL80211_VENDOR_SUBCMD_MPTA_HELPER_CONFIG: This sub command is used to |
| * improve the success rate of Zigbee joining network. |
| * Due to PTA master limitation, Zigbee joining network success rate is |
| * low while WLAN is working. The WLAN driver needs to configure some |
| * parameters including Zigbee state and specific WLAN periods to enhance |
| * PTA master. All these parameters are delivered by the attributes |
| * defined in enum qca_mpta_helper_vendor_attr. |
| * @QCA_NL80211_VENDOR_SUBCMD_BEACON_REPORTING: This sub command is used to |
| * implement Beacon frame reporting feature. |
| * |
| * Userspace can request the driver/firmware to periodically report |
| * received Beacon frames whose BSSID is same as the current connected |
| * BSS's MAC address. |
| * |
| * In case the STA seamlessly (without sending disconnect indication to |
| * userspace) roams to a different BSS, Beacon frame reporting will be |
| * automatically enabled for the Beacon frames whose BSSID is same as the |
| * MAC address of the new BSS. Beacon reporting will be stopped when the |
| * STA is disconnected (when the disconnect indication is sent to |
| * userspace) and need to be explicitly enabled by userspace for next |
| * connection. |
| * |
| * When a Beacon frame matching configured conditions is received, and if |
| * userspace has requested to send asynchronous beacon reports, the |
| * driver/firmware will encapsulate the details of the Beacon frame in an |
| * event and send it to userspace along with updating the BSS information |
| * in cfg80211 scan cache, otherwise driver will only update the cfg80211 |
| * scan cache with the information from the received Beacon frame but will |
| * not send any active report to userspace. |
| * |
| * The userspace can request the driver/firmware to stop reporting Beacon |
| * frames. If the driver/firmware is not able to receive Beacon frames due |
| * to other Wi-Fi operations such as off-channel activities, etc., the |
| * driver/firmware will send a pause event to userspace and stop reporting |
| * Beacon frames. Whether the beacon reporting will be automatically |
| * resumed or not by the driver/firmware later will be reported to |
| * userspace using the QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_AUTO_RESUMES |
| * flag. The beacon reporting shall be resumed for all the cases except |
| * either when userspace sets |
| * QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_DO_NOT_RESUME flag in the command |
| * which triggered the current beacon reporting or during any disconnection |
| * case as indicated by setting |
| * QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_PAUSE_REASON to |
| * QCA_WLAN_VENDOR_BEACON_REPORTING_PAUSE_REASON_DISCONNECTED by the |
| * driver. |
| * |
| * After QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_PAUSE event is received |
| * by userspace with QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_AUTO_RESUMES |
| * flag not set, the next first |
| * QCA_WLAN_VENDOR_BEACON_REPORTING_OP_BEACON_INFO event from the driver |
| * shall be considered as un-pause event. |
| * |
| * All the attributes used with this command are defined in |
| * enum qca_wlan_vendor_attr_beacon_reporting_params. |
| * @QCA_NL80211_VENDOR_SUBCMD_INTEROP_ISSUES_AP: In practice, some APs have |
| * interop issues with the DUT. This sub command is used to transfer the |
| * AP info between the driver and user space. This works both as a command |
| * and an event. As a command, it configures the stored list of APs from |
| * user space to firmware; as an event, it indicates the AP info detected |
| * by the firmware to user space for persistent storage. The attributes |
| * defined in enum qca_vendor_attr_interop_issues_ap are used to deliver |
| * the parameters. |
| * @QCA_NL80211_VENDOR_SUBCMD_OEM_DATA: This command/event is used to |
| * send/receive OEM data binary blobs to/from application/service to/from |
| * firmware. The attributes defined in enum |
| * qca_wlan_vendor_attr_oem_data_params are used to deliver the |
| * parameters. |
| * @QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY_EXT: This command/event is used |
| * to send/receive avoid frequency data using |
| * enum qca_wlan_vendor_attr_avoid_frequency_ext. |
| * This new command is alternative to existing command |
| * QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY since existing command/event |
| * is using stream of bytes instead of structured data using vendor |
| * attributes. User space sends unsafe frequency ranges to the driver using |
| * a nested attribute %QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_RANGE. On |
| * reception of this command, the driver shall check if an interface is |
| * operating on an unsafe frequency and the driver shall try to move to a |
| * safe channel when needed. If the driver is not able to find a safe |
| * channel the interface can keep operating on an unsafe channel with the |
| * TX power limit derived based on internal configurations like |
| * regulatory/SAR rules. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_ADD_STA_NODE: This vendor subcommand is used to |
| * add the STA node details in driver/firmware. Attributes for this event |
| * are specified in enum qca_wlan_vendor_attr_add_sta_node_params. |
| * @QCA_NL80211_VENDOR_SUBCMD_BTC_CHAIN_MODE: This command is used to set BT |
| * coex chain mode from application/service. |
| * The attributes defined in enum qca_vendor_attr_btc_chain_mode are used |
| * to deliver the parameters. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_GET_STA_INFO: This vendor subcommand is used to |
| * get information of a station from driver to userspace. This command can |
| * be used in both STA and AP modes. For STA mode, it provides information |
| * of the current association when in connected state or the last |
| * association when in disconnected state. For AP mode, only information |
| * of the currently connected stations is available. This command uses |
| * attributes defined in enum qca_wlan_vendor_attr_get_sta_info. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_REQUEST_SAR_LIMITS_EVENT: This acts as an event. |
| * Host drivers can request the user space entity to set the SAR power |
| * limits with this event. Accordingly, the user space entity is expected |
| * to set the SAR power limits. Host drivers can retry this event to the |
| * user space for the SAR power limits configuration from user space. If |
| * the driver does not get the SAR power limits from user space for all |
| * the retried attempts, it can configure a default SAR power limit. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_UPDATE_STA_INFO: This acts as a vendor event and |
| * is used to update the information about the station from the driver to |
| * userspace. Uses attributes from enum |
| * qca_wlan_vendor_attr_update_sta_info. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_DRIVER_DISCONNECT_REASON: This acts as an event. |
| * The host driver initiates the disconnection for scenarios such as beacon |
| * miss, NUD failure, peer kick out, etc. The disconnection indication |
| * through cfg80211_disconnected() expects the reason codes from enum |
| * ieee80211_reasoncode which does not signify these various reasons why |
| * the driver has triggered the disconnection. This event will be used to |
| * send the driver specific reason codes by the host driver to userspace. |
| * Host drivers should trigger this event and pass the respective reason |
| * code immediately prior to triggering cfg80211_disconnected(). The |
| * attributes used with this event are defined in enum |
| * qca_wlan_vendor_attr_driver_disconnect_reason. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_CONFIG_TSPEC: This vendor subcommand is used to |
| * add/delete TSPEC for each AC. One command is for one specific AC only. |
| * This command can only be used in STA mode and the STA must be |
| * associated with an AP when the command is issued. Uses attributes |
| * defined in enum qca_wlan_vendor_attr_config_tspec. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_CONFIG_TWT: Vendor subcommand to configure TWT. |
| * Uses attributes defined in enum qca_wlan_vendor_attr_config_twt. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_GETBAND: Command to get the enabled band(s) from |
| * the driver. The band configurations obtained are referred through |
| * QCA_WLAN_VENDOR_ATTR_SETBAND_MASK. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_MEDIUM_ASSESS: Vendor subcommand/event for medium |
| * assessment. |
| * Uses attributes defined in enum qca_wlan_vendor_attr_medium_assess. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_UPDATE_SSID: This acts as a vendor event and is |
| * used to update SSID information in hostapd when it is updated in the |
| * driver. Uses the attribute NL80211_ATTR_SSID. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_WIFI_FW_STATS: This vendor subcommand is used by |
| * the driver to send opaque data from the firmware to userspace. The |
| * driver sends an event to userspace whenever such data is received from |
| * the firmware. |
| * |
| * QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA is used as the attribute to |
| * send this opaque data for this event. |
| * |
| * The format of the opaque data is specific to the particular firmware |
| * version and there is no guarantee of the format remaining same. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_MBSSID_TX_VDEV_STATUS: This acts as an event. |
| * The host driver selects Tx VDEV, and notifies user. The attributes |
| * used with this event are defined in enum |
| * qca_wlan_vendor_attr_mbssid_tx_vdev_status. |
| * This event contains Tx VDEV group information, other VDEVs |
| * interface index, and status information. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_CONCURRENT_POLICY: Vendor command to |
| * configure the concurrent session policies when multiple interfaces |
| * are (getting) active. The attributes used by this command are defined |
| * in enum qca_wlan_vendor_attr_concurrent_policy. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_USABLE_CHANNELS: Userspace can use this command |
| * to query usable channels for different interface types such as STA, |
| * AP, P2P GO, P2P Client, NAN, etc. The driver shall report all usable |
| * channels in the response based on country code, different static |
| * configurations, concurrency combinations, etc. The attributes used |
| * with this command are defined in |
| * enum qca_wlan_vendor_attr_usable_channels. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_GET_RADAR_HISTORY: This vendor subcommand is used |
| * to get DFS radar history from the driver to userspace. The driver |
| * returns QCA_WLAN_VENDOR_ATTR_RADAR_HISTORY_ENTRIES attribute with an |
| * array of nested entries. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_MDNS_OFFLOAD: Userspace can use this command to |
| * enable/disable mDNS offload to the firmware. The attributes used with |
| * this command are defined in enum qca_wlan_vendor_attr_mdns_offload. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_SET_MONITOR_MODE: This vendor subcommand is used |
| * to set packet monitor mode that aims to send the specified set of TX and |
| * RX frames on the current client interface to an active monitor |
| * interface. If this monitor mode is set, the driver will send the |
| * configured frames, from the interface on which the command is issued, to |
| * an active monitor interface. The attributes used with this command are |
| * defined in enum qca_wlan_vendor_attr_set_monitor_mode. |
| * |
| * Though the monitor mode is configured for the respective |
| * Data/Management/Control frames, it is up to the respective WLAN |
| * driver/firmware/hardware designs to consider the possibility of sending |
| * these frames over the monitor interface. For example, the Control frames |
| * are handled within the hardware and thus passing such frames over the |
| * monitor interface is left to the respective designs. |
| * |
| * Also, this monitor mode is governed to behave accordingly in |
| * suspend/resume states. If the firmware handles any of such frames in |
| * suspend state without waking up the host and if the monitor mode is |
| * configured to notify all such frames, the firmware is expected to resume |
| * the host and forward the respective frames to the monitor interface. |
| * Please note that such a request to get the frames over the monitor |
| * interface will have a definite power implication. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_ROAM_EVENTS: This vendor subcommand is used both |
| * as a request to set the driver/firmware with the parameters to trigger |
| * the roaming events, and also used by the driver/firmware to pass on the |
| * various roam events to userspace. |
| * Applicable only for the STA mode. The attributes used with this command |
| * are defined in enum qca_wlan_vendor_attr_roam_events. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_RATEMASK_CONFIG: Subcommand to set or reset the |
| * rate mask config for a list of PHY types. Userspace shall provide an |
| * array of the vendor attributes defined in |
| * enum qca_wlan_vendor_attr_ratemask_params. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_MCC_QUOTA: Multi-channel Concurrency (MCC) occurs |
| * when two interfaces are active on the same band, using two different |
| * home channels, and only supported by a single radio. In this scenario |
| * the device must split the use of the radio between the two interfaces. |
| * The percentage of time allocated to a given interface is the quota. |
| * Depending on the configuration, the quota can either be fixed or |
| * dynamic. |
| * |
| * When used as an event, the device will report the quota type, and for |
| * all interfaces operating in MCC it will report the current quota. |
| * When used as a command, the device can be configured for a specific |
| * quota type, and in the case of a fixed quota, the quota to apply to one |
| * of the interfaces. |
| * |
| * Applications can use the event to do TX bitrate control based on the |
| * information, and can use the command to explicitly set the quota to |
| * enhance performance in specific scenarios. |
| * |
| * The attributes used with this command are defined in |
| * enum qca_wlan_vendor_attr_mcc_quota. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_GET_RADIO_COMBINATION_MATRIX: Vendor command to |
| * get the WLAN radio combinations matrix supported by the device which |
| * provides the device simultaneous radio configurations such as |
| * standalone, dual band simultaneous, and single band simultaneous. |
| * |
| * The attributes used with this command are defined in |
| * enum qca_wlan_vendor_attr_radio_combination_matrix. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_DRIVER_READY: Event indicating to the user space |
| * that the driver is ready for operations again after recovering from |
| * internal failures. This occurs following a failure that was indicated by |
| * @QCA_NL80211_VENDOR_SUBCMD_HANG. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_PASN: Subcommand used to offload preassociation |
| * security negotiation and key generation to user space. |
| * |
| * When used as an event, the driver requests userspace to trigger the PASN |
| * authentication or dropping of a PTKSA for the indicated peer devices. |
| * When used as a command response, userspace indicates a consolidated |
| * status report for all the peers that were requested for. |
| * |
| * The attributes used with this command are defined in |
| * enum qca_wlan_vendor_attr_pasn. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_SECURE_RANGING_CONTEXT: Subcommand used to set |
| * secure ranging context such as TK and LTF keyseed for each peer |
| * requested by the driver with a @QCA_NL80211_VENDOR_SUBCMD_PASN event. |
| * |
| * The attributes used with this command are defined in |
| * enum qca_wlan_vendor_attr_secure_ranging_ctx. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_COAP_OFFLOAD: This vendor subcommand is used to |
| * enable/disable offload processing in firmware during system/runtime |
| * suspend for CoAP messages (see RFC7252: The Constrained Application |
| * Protocol) and fetch information of the CoAP messages cached during |
| * offload processing. |
| * |
| * The attributes used with this command are defined in |
| * enum qca_wlan_vendor_attr_coap_offload. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_SCS_RULE_CONFIG: Subcommand to configure |
| * (add, remove, or change) a Stream Classification Service (SCS) rule. |
| * |
| * The attributes used with this event are defined in |
| * enum qca_wlan_vendor_attr_scs_rule_config. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_GET_SAR_CAPABILITY: Fetch SAR capabilities |
| * supported by the WLAN firmware. |
| * |
| * The attributes used with this command are defined in |
| * enum qca_wlan_vendor_attr_sar_capability. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_SR: Subcommand used to implement Spatial Reuse |
| * (SR) feature. This command is used by userspace to configure SR |
| * parameters to the driver and to get the SR related parameters and |
| * statistics with synchronous responses from the driver. |
| * The driver also uses this command to send asynchronous events to |
| * userspace to indicate suspend/resume of SR feature and changes |
| * in SR parameters. |
| * |
| * The attributes used with this command are defined in |
| * enum qca_wlan_vendor_attr_sr. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_MLO_PEER_PRIM_NETDEV_EVENT: Subcommand used to |
| * notify application layer about the primary netdev of an MLO connection. |
| * In some implementations, MLO has multiple netdevs out of which one |
| * netdev is designated as primary to provide a unified interface to the |
| * bridge. In those implementations this event is sent on every MLO peer |
| * connection. |
| * |
| * The attributes used with this event are defined in |
| * enum qca_wlan_vendor_attr_mlo_peer_prim_netdev_event. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_AFC_EVENT: This vendor command is used by the |
| * driver to notify different AFC events to userspace. The attributes used |
| * with this command are defined in enum qca_wlan_vendor_attr_afc_event. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_AFC_RESPONSE: This vendor command is used by |
| * userspace to deliver AFC response data to driver. The attributes used |
| * with this command are defined in enum qca_wlan_vendor_attr_afc_response. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_DOZED_AP: Subcommand to configure AP interface to |
| * operate in doze mode. |
| * |
| * Userspace uses this command to configure the AP interface to enter or |
| * exit from doze mode. The driver sends this event after it enters or |
| * exits the doze mode with the updated AP doze mode settings. |
| * |
| * The attributes used with this subcommand are defined in |
| * enum qca_wlan_vendor_attr_dozed_ap. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_GET_MONITOR_MODE: This vendor subcommand is used |
| * to get the status of local packet capture of monitor mode. The monitor |
| * mode can be started using QCA_NL80211_VENDOR_SUBCMD_SET_MONITOR_MODE |
| * subcommand. |
| * |
| * The attributes used with this command are defined in enum |
| * qca_wlan_vendor_attr_get_monitor_mode. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_ROAM_STATS: This vendor command is used to |
| * get roam information from the driver to user space. It provides the |
| * latest several instances of roam information cached in the driver. |
| * The command is only used for STA mode. The attributes used with this |
| * command are defined in enum qca_wlan_vendor_attr_roam_cached_stats. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_MLO_LINK_STATE: This vendor subcommand is used to |
| * configure and fetch the state information of the MLO links affiliated |
| * with the STA interface. The attributes used with this command are |
| * defined in enum qca_wlan_vendor_attr_mlo_link_state. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_CONNECTED_CHANNEL_STATS: Userspace can use this |
| * vendor subcommand to trigger channel utilization measurement on entire |
| * channel width of the connected channel(s). For MLO connection, connected |
| * channel utilization measurement shall be done on all the MLO links. |
| * The driver may use regular scan or wideband energy detection feature |
| * based on the hardware capability for connected channel(s) utilization |
| * measurement. The driver indicates the connected channel(s) utilization |
| * measurement completion as an asynchronous event with this command ID to |
| * userspace. Upon receiving this event, userspace can use |
| * %NL80211_CMD_GET_INTERFACE to determine the channel width of the current |
| * connected channel(s) and can derive the channel utilization percentage |
| * (CU) of each 20 MHz sub-channel of the entire connected channel using |
| * %NL80211_CMD_GET_SURVEY response. |
| * CU = %NL80211_SURVEY_INFO_TIME_BUSY * 100 / %NL80211_SURVEY_INFO_TIME. |
| * This command is only used for STA mode. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_TID_TO_LINK_MAP: This vendor subcommand is |
| * used as an event to notify the userspace of TID-to-link map changes |
| * negotiated by the driver or updated by associated AP MLD with Beacon, |
| * Probe Response, or Action frames. The attributes used with this command |
| * are defined in enum qca_wlan_vendor_attr_tid_to_link_map. |
| * |
| * Note that the attribute |
| * %QCA_WLAN_VENDOR_ATTR_TID_TO_LINK_MAP_AP_MLD_ADDR may not correspond to |
| * the current connected AP MLD address. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_LINK_RECONFIG: Notify userspace about the removal |
| * of STA MLD setup links due to the AP MLD removing the corresponding |
| * affiliated APs with Multi-Link reconfiguration. If all the STA MLD setup |
| * links are removed during Multi-Link reconfiguration, the driver shall |
| * use %NL80211_CMD_DISCONNECT instead of this command since it is a |
| * connection drop. The attributes used with this command are defined in |
| * enum qca_wlan_vendor_attr_link_reconfig. |
| * Note that the attribute |
| * %QCA_WLAN_VENDOR_ATTR_LINK_RECONFIG_AP_MLD_ADDR may not correspond to |
| * the current connected AP MLD address. |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_TDLS_DISC_RSP_EXT: Vendor command to configure |
| * the driver with MLO link id information on which to transmit the TDLS |
| * discovery response frame on the configured MLO BSS link when the |
| * local station is connected in MLO mode. This command is sent to the |
| * driver prior to the TDLS discovery response management transmit |
| * operation and is followed immediately by the TDLS discovery response |
| * management frame transmit command. |
| * |
| * The driver saves the configured MLO link id information and uses it for |
| * the following TDLS discovery response frame transmission on the |
| * configured MLO BSS link and the link id information is cleared in the |
| * driver after the TDLS discovery response frame is successfully |
| * transmitted. This behavior is indepent of the TDLS peer STA connection |
| * mode (MLO or non-MLO). |
| * |
| * Uses the attributes defined in |
| * enum qca_wlan_vendor_attr_tdls_disc_rsp_ext. |
| */ |
| enum qca_nl80211_vendor_subcmds { |
| QCA_NL80211_VENDOR_SUBCMD_UNSPEC = 0, |
| QCA_NL80211_VENDOR_SUBCMD_TEST = 1, |
| /* subcmds 2..8 not yet allocated */ |
| QCA_NL80211_VENDOR_SUBCMD_ROAMING = 9, |
| QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY = 10, |
| QCA_NL80211_VENDOR_SUBCMD_DFS_CAPABILITY = 11, |
| QCA_NL80211_VENDOR_SUBCMD_NAN = 12, |
| QCA_NL80211_VENDOR_SUBCMD_STATS_EXT = 13, |
| QCA_NL80211_VENDOR_SUBCMD_LL_STATS_SET = 14, |
| QCA_NL80211_VENDOR_SUBCMD_LL_STATS_GET = 15, |
| QCA_NL80211_VENDOR_SUBCMD_LL_STATS_CLR = 16, |
| QCA_NL80211_VENDOR_SUBCMD_LL_STATS_RADIO_RESULTS = 17, |
| QCA_NL80211_VENDOR_SUBCMD_LL_STATS_IFACE_RESULTS = 18, |
| QCA_NL80211_VENDOR_SUBCMD_LL_STATS_PEERS_RESULTS = 19, |
| QCA_NL80211_VENDOR_SUBCMD_GSCAN_START = 20, |
| QCA_NL80211_VENDOR_SUBCMD_GSCAN_STOP = 21, |
| QCA_NL80211_VENDOR_SUBCMD_GSCAN_GET_VALID_CHANNELS = 22, |
| QCA_NL80211_VENDOR_SUBCMD_GSCAN_GET_CAPABILITIES = 23, |
| QCA_NL80211_VENDOR_SUBCMD_GSCAN_GET_CACHED_RESULTS = 24, |
| QCA_NL80211_VENDOR_SUBCMD_GSCAN_SCAN_RESULTS_AVAILABLE = 25, |
| QCA_NL80211_VENDOR_SUBCMD_GSCAN_FULL_SCAN_RESULT = 26, |
| QCA_NL80211_VENDOR_SUBCMD_GSCAN_SCAN_EVENT = 27, |
| QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_AP_FOUND = 28, |
| QCA_NL80211_VENDOR_SUBCMD_GSCAN_SET_BSSID_HOTLIST = 29, |
| QCA_NL80211_VENDOR_SUBCMD_GSCAN_RESET_BSSID_HOTLIST = 30, |
| QCA_NL80211_VENDOR_SUBCMD_GSCAN_SIGNIFICANT_CHANGE = 31, |
| QCA_NL80211_VENDOR_SUBCMD_GSCAN_SET_SIGNIFICANT_CHANGE = 32, |
| QCA_NL80211_VENDOR_SUBCMD_GSCAN_RESET_SIGNIFICANT_CHANGE = 33, |
| QCA_NL80211_VENDOR_SUBCMD_TDLS_ENABLE = 34, |
| QCA_NL80211_VENDOR_SUBCMD_TDLS_DISABLE = 35, |
| QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_STATUS = 36, |
| QCA_NL80211_VENDOR_SUBCMD_TDLS_STATE = 37, |
| QCA_NL80211_VENDOR_SUBCMD_GET_SUPPORTED_FEATURES = 38, |
| QCA_NL80211_VENDOR_SUBCMD_SCANNING_MAC_OUI = 39, |
| QCA_NL80211_VENDOR_SUBCMD_NO_DFS_FLAG = 40, |
| QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_AP_LOST = 41, |
| QCA_NL80211_VENDOR_SUBCMD_GET_CONCURRENCY_MATRIX = 42, |
| /* 43..49 - reserved for QCA */ |
| QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_SET_KEY = 50, |
| QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH = 51, |
| QCA_NL80211_VENDOR_SUBCMD_APFIND = 52, |
| /* 53 - reserved - was used by QCA, but not in use anymore */ |
| QCA_NL80211_VENDOR_SUBCMD_DO_ACS = 54, |
| QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES = 55, |
| QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_STARTED = 56, |
| QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_FINISHED = 57, |
| QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_ABORTED = 58, |
| QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_NOP_FINISHED = 59, |
| QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_RADAR_DETECTED = 60, |
| QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_INFO = 61, |
| QCA_NL80211_VENDOR_SUBCMD_WIFI_LOGGER_START = 62, |
| QCA_NL80211_VENDOR_SUBCMD_WIFI_LOGGER_MEMORY_DUMP = 63, |
| QCA_NL80211_VENDOR_SUBCMD_ROAM = 64, |
| QCA_NL80211_VENDOR_SUBCMD_GSCAN_SET_SSID_HOTLIST = 65, |
| QCA_NL80211_VENDOR_SUBCMD_GSCAN_RESET_SSID_HOTLIST = 66, |
| QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_SSID_FOUND = 67, |
| QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_SSID_LOST = 68, |
| QCA_NL80211_VENDOR_SUBCMD_PNO_SET_LIST = 69, |
| QCA_NL80211_VENDOR_SUBCMD_PNO_SET_PASSPOINT_LIST = 70, |
| QCA_NL80211_VENDOR_SUBCMD_PNO_RESET_PASSPOINT_LIST = 71, |
| QCA_NL80211_VENDOR_SUBCMD_PNO_NETWORK_FOUND = 72, |
| QCA_NL80211_VENDOR_SUBCMD_PNO_PASSPOINT_NETWORK_FOUND = 73, |
| /* Wi-Fi configuration subcommands */ |
| QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION = 74, |
| QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION = 75, |
| QCA_NL80211_VENDOR_SUBCMD_GET_LOGGER_FEATURE_SET = 76, |
| QCA_NL80211_VENDOR_SUBCMD_GET_RING_DATA = 77, |
| QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_CAPABILITIES = 78, |
| QCA_NL80211_VENDOR_SUBCMD_OFFLOADED_PACKETS = 79, |
| QCA_NL80211_VENDOR_SUBCMD_MONITOR_RSSI = 80, |
| QCA_NL80211_VENDOR_SUBCMD_NDP = 81, |
| QCA_NL80211_VENDOR_SUBCMD_ND_OFFLOAD = 82, |
| QCA_NL80211_VENDOR_SUBCMD_PACKET_FILTER = 83, |
| QCA_NL80211_VENDOR_SUBCMD_GET_BUS_SIZE = 84, |
| QCA_NL80211_VENDOR_SUBCMD_GET_WAKE_REASON_STATS = 85, |
| /* 86-90 - reserved for QCA */ |
| QCA_NL80211_VENDOR_SUBCMD_DATA_OFFLOAD = 91, |
| QCA_NL80211_VENDOR_SUBCMD_OCB_SET_CONFIG = 92, |
| QCA_NL80211_VENDOR_SUBCMD_OCB_SET_UTC_TIME = 93, |
| QCA_NL80211_VENDOR_SUBCMD_OCB_START_TIMING_ADVERT = 94, |
| QCA_NL80211_VENDOR_SUBCMD_OCB_STOP_TIMING_ADVERT = 95, |
| QCA_NL80211_VENDOR_SUBCMD_OCB_GET_TSF_TIMER = 96, |
| QCA_NL80211_VENDOR_SUBCMD_DCC_GET_STATS = 97, |
| QCA_NL80211_VENDOR_SUBCMD_DCC_CLEAR_STATS = 98, |
| QCA_NL80211_VENDOR_SUBCMD_DCC_UPDATE_NDL = 99, |
| QCA_NL80211_VENDOR_SUBCMD_DCC_STATS_EVENT = 100, |
| QCA_NL80211_VENDOR_SUBCMD_LINK_PROPERTIES = 101, |
| QCA_NL80211_VENDOR_SUBCMD_GW_PARAM_CONFIG = 102, |
| QCA_NL80211_VENDOR_SUBCMD_GET_PREFERRED_FREQ_LIST = 103, |
| QCA_NL80211_VENDOR_SUBCMD_SET_PROBABLE_OPER_CHANNEL = 104, |
| QCA_NL80211_VENDOR_SUBCMD_SETBAND = 105, |
| QCA_NL80211_VENDOR_SUBCMD_TRIGGER_SCAN = 106, |
| QCA_NL80211_VENDOR_SUBCMD_SCAN_DONE = 107, |
| QCA_NL80211_VENDOR_SUBCMD_OTA_TEST = 108, |
| QCA_NL80211_VENDOR_SUBCMD_SET_TXPOWER_SCALE = 109, |
| /* 110..114 - reserved for QCA */ |
| QCA_NL80211_VENDOR_SUBCMD_SET_TXPOWER_DECR_DB = 115, |
| QCA_NL80211_VENDOR_SUBCMD_ACS_POLICY = 116, |
| /* 117 - reserved for QCA */ |
| QCA_NL80211_VENDOR_SUBCMD_SET_SAP_CONFIG = 118, |
| QCA_NL80211_VENDOR_SUBCMD_TSF = 119, |
| QCA_NL80211_VENDOR_SUBCMD_WISA = 120, |
| /* 121 - reserved for QCA */ |
| QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_START = 122, |
| QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_STOP = 123, |
| QCA_NL80211_VENDOR_SUBCMD_SAP_CONDITIONAL_CHAN_SWITCH = 124, |
| QCA_NL80211_VENDOR_SUBCMD_GPIO_CONFIG_COMMAND = 125, |
| QCA_NL80211_VENDOR_SUBCMD_GET_HW_CAPABILITY = 126, |
| QCA_NL80211_VENDOR_SUBCMD_LL_STATS_EXT = 127, |
| /* FTM/indoor location subcommands */ |
| QCA_NL80211_VENDOR_SUBCMD_LOC_GET_CAPA = 128, |
| QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION = 129, |
| QCA_NL80211_VENDOR_SUBCMD_FTM_ABORT_SESSION = 130, |
| QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT = 131, |
| QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE = 132, |
| QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER = 133, |
| QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS = 134, |
| QCA_NL80211_VENDOR_SUBCMD_AOA_ABORT_MEAS = 135, |
| QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT = 136, |
| QCA_NL80211_VENDOR_SUBCMD_ENCRYPTION_TEST = 137, |
| QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI = 138, |
| /* DMG low level RF sector operations */ |
| QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SECTOR_CFG = 139, |
| QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SECTOR_CFG = 140, |
| QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SELECTED_SECTOR = 141, |
| QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SELECTED_SECTOR = 142, |
| QCA_NL80211_VENDOR_SUBCMD_CONFIGURE_TDLS = 143, |
| QCA_NL80211_VENDOR_SUBCMD_GET_HE_CAPABILITIES = 144, |
| QCA_NL80211_VENDOR_SUBCMD_ABORT_SCAN = 145, |
| QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS = 146, |
| QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS = 147, |
| QCA_NL80211_VENDOR_SUBCMD_CHIP_PWRSAVE_FAILURE = 148, |
| QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_SET = 149, |
| QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_GET = 150, |
| QCA_NL80211_VENDOR_SUBCMD_FETCH_BSS_TRANSITION_STATUS = 151, |
| QCA_NL80211_VENDOR_SUBCMD_SET_TRACE_LEVEL = 152, |
| QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT = 153, |
| QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START = 154, |
| QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_STOP = 155, |
| QCA_NL80211_VENDOR_SUBCMD_ACTIVE_TOS = 156, |
| QCA_NL80211_VENDOR_SUBCMD_HANG = 157, |
| QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CONFIG = 158, |
| QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_DIAG_STATS = 159, |
| QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO = 160, |
| QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_STATUS = 161, |
| /* Flush peer pending data */ |
| QCA_NL80211_VENDOR_SUBCMD_PEER_FLUSH_PENDING = 162, |
| QCA_NL80211_VENDOR_SUBCMD_GET_RROP_INFO = 163, |
| QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS = 164, |
| QCA_NL80211_VENDOR_SUBCMD_WLAN_MAC_INFO = 165, |
| QCA_NL80211_VENDOR_SUBCMD_SET_QDEPTH_THRESH = 166, |
| /* Thermal shutdown commands to protect wifi chip */ |
| QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD = 167, |
| QCA_NL80211_VENDOR_SUBCMD_THERMAL_EVENT = 168, |
| /* Wi-Fi test configuration subcommand */ |
| QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION = 169, |
| /* Frame filter operations for other BSSs/unassociated STAs */ |
| QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER = 170, |
| QCA_NL80211_VENDOR_SUBCMD_NAN_EXT = 171, |
| QCA_NL80211_VENDOR_SUBCMD_ROAM_SCAN_EVENT = 172, |
| QCA_NL80211_VENDOR_SUBCMD_PEER_CFR_CAPTURE_CFG = 173, |
| QCA_NL80211_VENDOR_SUBCMD_THROUGHPUT_CHANGE_EVENT = 174, |
| QCA_NL80211_VENDOR_SUBCMD_COEX_CONFIG = 175, |
| QCA_NL80211_VENDOR_SUBCMD_GET_SUPPORTED_AKMS = 176, |
| QCA_NL80211_VENDOR_SUBCMD_GET_FW_STATE = 177, |
| QCA_NL80211_VENDOR_SUBCMD_PEER_STATS_CACHE_FLUSH = 178, |
| QCA_NL80211_VENDOR_SUBCMD_MPTA_HELPER_CONFIG = 179, |
| QCA_NL80211_VENDOR_SUBCMD_BEACON_REPORTING = 180, |
| QCA_NL80211_VENDOR_SUBCMD_INTEROP_ISSUES_AP = 181, |
| QCA_NL80211_VENDOR_SUBCMD_OEM_DATA = 182, |
| QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY_EXT = 183, |
| QCA_NL80211_VENDOR_SUBCMD_ADD_STA_NODE = 184, |
| QCA_NL80211_VENDOR_SUBCMD_BTC_CHAIN_MODE = 185, |
| QCA_NL80211_VENDOR_SUBCMD_GET_STA_INFO = 186, |
| QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS_EVENT = 187, |
| QCA_NL80211_VENDOR_SUBCMD_UPDATE_STA_INFO = 188, |
| QCA_NL80211_VENDOR_SUBCMD_DRIVER_DISCONNECT_REASON = 189, |
| QCA_NL80211_VENDOR_SUBCMD_CONFIG_TSPEC = 190, |
| QCA_NL80211_VENDOR_SUBCMD_CONFIG_TWT = 191, |
| QCA_NL80211_VENDOR_SUBCMD_GETBAND = 192, |
| QCA_NL80211_VENDOR_SUBCMD_MEDIUM_ASSESS = 193, |
| QCA_NL80211_VENDOR_SUBCMD_UPDATE_SSID = 194, |
| QCA_NL80211_VENDOR_SUBCMD_WIFI_FW_STATS = 195, |
| QCA_NL80211_VENDOR_SUBCMD_MBSSID_TX_VDEV_STATUS = 196, |
| QCA_NL80211_VENDOR_SUBCMD_CONCURRENT_POLICY = 197, |
| QCA_NL80211_VENDOR_SUBCMD_USABLE_CHANNELS = 198, |
| QCA_NL80211_VENDOR_SUBCMD_GET_RADAR_HISTORY = 199, |
| QCA_NL80211_VENDOR_SUBCMD_MDNS_OFFLOAD = 200, |
| /* 201 - reserved for QCA */ |
| QCA_NL80211_VENDOR_SUBCMD_SET_MONITOR_MODE = 202, |
| QCA_NL80211_VENDOR_SUBCMD_ROAM_EVENTS = 203, |
| QCA_NL80211_VENDOR_SUBCMD_RATEMASK_CONFIG = 204, |
| QCA_NL80211_VENDOR_SUBCMD_MCC_QUOTA = 205, |
| /* 206..212 - reserved for QCA */ |
| QCA_NL80211_VENDOR_SUBCMD_GET_RADIO_COMBINATION_MATRIX = 213, |
| QCA_NL80211_VENDOR_SUBCMD_DRIVER_READY = 214, |
| QCA_NL80211_VENDOR_SUBCMD_PASN = 215, |
| QCA_NL80211_VENDOR_SUBCMD_SECURE_RANGING_CONTEXT = 216, |
| QCA_NL80211_VENDOR_SUBCMD_COAP_OFFLOAD = 217, |
| QCA_NL80211_VENDOR_SUBCMD_SCS_RULE_CONFIG = 218, |
| QCA_NL80211_VENDOR_SUBCMD_GET_SAR_CAPABILITY = 219, |
| QCA_NL80211_VENDOR_SUBCMD_SR = 220, |
| QCA_NL80211_VENDOR_SUBCMD_MLO_PEER_PRIM_NETDEV_EVENT = 221, |
| QCA_NL80211_VENDOR_SUBCMD_AFC_EVENT = 222, |
| QCA_NL80211_VENDOR_SUBCMD_AFC_RESPONSE = 223, |
| QCA_NL80211_VENDOR_SUBCMD_DOZED_AP = 224, |
| QCA_NL80211_VENDOR_SUBCMD_GET_MONITOR_MODE = 225, |
| QCA_NL80211_VENDOR_SUBCMD_ROAM_STATS = 226, |
| QCA_NL80211_VENDOR_SUBCMD_MLO_LINK_STATE = 227, |
| QCA_NL80211_VENDOR_SUBCMD_CONNECTED_CHANNEL_STATS = 228, |
| QCA_NL80211_VENDOR_SUBCMD_TID_TO_LINK_MAP = 229, |
| QCA_NL80211_VENDOR_SUBCMD_LINK_RECONFIG = 230, |
| QCA_NL80211_VENDOR_SUBCMD_TDLS_DISC_RSP_EXT = 231, |
| }; |
| |
| /* Compatibility defines for previously used subcmd names. |
| * These values should not be used in any new implementation. |
| */ |
| #define QCA_NL80211_VENDOR_SUBCMD_CONCURRENT_MULTI_STA_POLICY \ |
| QCA_NL80211_VENDOR_SUBCMD_CONCURRENT_POLICY |
| |
| enum qca_wlan_vendor_attr { |
| QCA_WLAN_VENDOR_ATTR_INVALID = 0, |
| /* used by QCA_NL80211_VENDOR_SUBCMD_DFS_CAPABILITY */ |
| QCA_WLAN_VENDOR_ATTR_DFS = 1, |
| /* Used only when driver sends vendor events to the userspace under the |
| * command QCA_NL80211_VENDOR_SUBCMD_NAN. Not used when userspace sends |
| * commands to the driver. |
| */ |
| QCA_WLAN_VENDOR_ATTR_NAN = 2, |
| /* used by QCA_NL80211_VENDOR_SUBCMD_STATS_EXT */ |
| QCA_WLAN_VENDOR_ATTR_STATS_EXT = 3, |
| /* used by QCA_NL80211_VENDOR_SUBCMD_STATS_EXT */ |
| QCA_WLAN_VENDOR_ATTR_IFINDEX = 4, |
| /* used by QCA_NL80211_VENDOR_SUBCMD_ROAMING, u32 with values defined |
| * by enum qca_roaming_policy. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAMING_POLICY = 5, |
| QCA_WLAN_VENDOR_ATTR_MAC_ADDR = 6, |
| /* used by QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES */ |
| QCA_WLAN_VENDOR_ATTR_FEATURE_FLAGS = 7, |
| QCA_WLAN_VENDOR_ATTR_TEST = 8, |
| /* used by QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES */ |
| /* Unsigned 32-bit value. */ |
| QCA_WLAN_VENDOR_ATTR_CONCURRENCY_CAPA = 9, |
| /* Unsigned 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_MAX_CONCURRENT_CHANNELS_2_4_BAND = 10, |
| /* Unsigned 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_MAX_CONCURRENT_CHANNELS_5_0_BAND = 11, |
| /* Unsigned 32-bit value from enum qca_set_band. The allowed values for |
| * this attribute are limited to QCA_SETBAND_AUTO, QCA_SETBAND_5G, and |
| * QCA_SETBAND_2G. This attribute is deprecated. Recommendation is to |
| * use QCA_WLAN_VENDOR_ATTR_SETBAND_MASK instead. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE = 12, |
| /* Attribute used for padding for 64-bit alignment */ |
| QCA_WLAN_VENDOR_ATTR_PAD = 13, |
| /* Unique FTM session cookie (Unsigned 64 bit). Specified in |
| * QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION. Reported in |
| * the session in QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT and |
| * QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE. |
| */ |
| QCA_WLAN_VENDOR_ATTR_FTM_SESSION_COOKIE = 14, |
| /* Indoor location capabilities, returned by |
| * QCA_NL80211_VENDOR_SUBCMD_LOC_GET_CAPA. |
| * see enum qca_wlan_vendor_attr_loc_capa. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LOC_CAPA = 15, |
| /* Array of nested attributes containing information about each peer |
| * in FTM measurement session. See enum qca_wlan_vendor_attr_peer_info |
| * for supported attributes for each peer. |
| */ |
| QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PEERS = 16, |
| /* Array of nested attributes containing measurement results for |
| * one or more peers, reported by the |
| * QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT event. |
| * See enum qca_wlan_vendor_attr_peer_result for list of supported |
| * attributes. |
| */ |
| QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PEER_RESULTS = 17, |
| /* Flag attribute for enabling or disabling responder functionality. */ |
| QCA_WLAN_VENDOR_ATTR_FTM_RESPONDER_ENABLE = 18, |
| /* Used in the QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER |
| * command to specify the LCI report that will be sent by |
| * the responder during a measurement exchange. The format is |
| * defined in IEEE P802.11-REVmc/D7.0, 9.4.2.22.10. |
| */ |
| QCA_WLAN_VENDOR_ATTR_FTM_LCI = 19, |
| /* Used in the QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER |
| * command to specify the location civic report that will |
| * be sent by the responder during a measurement exchange. |
| * The format is defined in IEEE P802.11-REVmc/D7.0, 9.4.2.22.13. |
| */ |
| QCA_WLAN_VENDOR_ATTR_FTM_LCR = 20, |
| /* Session/measurement completion status code, |
| * reported in QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE and |
| * QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT |
| * see enum qca_vendor_attr_loc_session_status. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS = 21, |
| /* Initial dialog token used by responder (0 if not specified), |
| * unsigned 8 bit value. |
| */ |
| QCA_WLAN_VENDOR_ATTR_FTM_INITIAL_TOKEN = 22, |
| /* AOA measurement type. Requested in QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS |
| * and optionally in QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION if |
| * AOA measurements are needed as part of an FTM session. |
| * Reported by QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT. See |
| * enum qca_wlan_vendor_attr_aoa_type. |
| */ |
| QCA_WLAN_VENDOR_ATTR_AOA_TYPE = 23, |
| /* A bit mask (unsigned 32 bit value) of antenna arrays used |
| * by indoor location measurements. Refers to the antenna |
| * arrays described by QCA_VENDOR_ATTR_LOC_CAPA_ANTENNA_ARRAYS. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LOC_ANTENNA_ARRAY_MASK = 24, |
| /* AOA measurement data. Its contents depends on the AOA measurement |
| * type and antenna array mask: |
| * QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE: array of U16 values, |
| * phase of the strongest CIR path for each antenna in the measured |
| * array(s). |
| * QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE_AMP: array of 2 U16 |
| * values, phase and amplitude of the strongest CIR path for each |
| * antenna in the measured array(s). |
| */ |
| QCA_WLAN_VENDOR_ATTR_AOA_MEAS_RESULT = 25, |
| /* Used in QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI command |
| * to specify the chain number (unsigned 32 bit value) to inquire |
| * the corresponding antenna RSSI value |
| */ |
| QCA_WLAN_VENDOR_ATTR_CHAIN_INDEX = 26, |
| /* Used in QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI command |
| * to report the specific antenna RSSI value (unsigned 32 bit value) |
| */ |
| QCA_WLAN_VENDOR_ATTR_CHAIN_RSSI = 27, |
| /* Frequency in MHz, various uses. Unsigned 32 bit value */ |
| QCA_WLAN_VENDOR_ATTR_FREQ = 28, |
| /* TSF timer value, unsigned 64 bit value. |
| * May be returned by various commands. |
| */ |
| QCA_WLAN_VENDOR_ATTR_TSF = 29, |
| /* DMG RF sector index, unsigned 16 bit number. Valid values are |
| * 0..127 for sector indices or 65535 as special value used to |
| * unlock sector selection in |
| * QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SELECTED_SECTOR. |
| */ |
| QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX = 30, |
| /* DMG RF sector type, unsigned 8 bit value. One of the values |
| * in enum qca_wlan_vendor_attr_dmg_rf_sector_type. |
| */ |
| QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE = 31, |
| /* Bitmask of DMG RF modules for which information is requested. Each |
| * bit corresponds to an RF module with the same index as the bit |
| * number. Unsigned 32 bit number but only low 8 bits can be set since |
| * all DMG chips currently have up to 8 RF modules. |
| */ |
| QCA_WLAN_VENDOR_ATTR_DMG_RF_MODULE_MASK = 32, |
| /* Array of nested attributes where each entry is DMG RF sector |
| * configuration for a single RF module. |
| * Attributes for each entry are taken from enum |
| * qca_wlan_vendor_attr_dmg_rf_sector_cfg. |
| * Specified in QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SECTOR_CFG |
| * and returned by QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SECTOR_CFG. |
| */ |
| QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG = 33, |
| /* Used in QCA_NL80211_VENDOR_SUBCMD_STATS_EXT command |
| * to report frame aggregation statistics to userspace. |
| */ |
| QCA_WLAN_VENDOR_ATTR_RX_AGGREGATION_STATS_HOLES_NUM = 34, |
| QCA_WLAN_VENDOR_ATTR_RX_AGGREGATION_STATS_HOLES_INFO = 35, |
| /* Unsigned 8-bit value representing MBO transition reason code as |
| * provided by the AP used by subcommand |
| * QCA_NL80211_VENDOR_SUBCMD_FETCH_BSS_TRANSITION_STATUS. This is |
| * specified by the userspace in the request to the driver. |
| */ |
| QCA_WLAN_VENDOR_ATTR_BTM_MBO_TRANSITION_REASON = 36, |
| /* Array of nested attributes, BSSID and status code, used by subcommand |
| * QCA_NL80211_VENDOR_SUBCMD_FETCH_BSS_TRANSITION_STATUS, where each |
| * entry is taken from enum qca_wlan_vendor_attr_btm_candidate_info. |
| * The userspace space specifies the list/array of candidate BSSIDs in |
| * the order of preference in the request. The driver specifies the |
| * status code, for each BSSID in the list, in the response. The |
| * acceptable candidates are listed in the order preferred by the |
| * driver. |
| */ |
| QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO = 37, |
| /* Used in QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT command |
| * See enum qca_wlan_vendor_attr_brp_ant_limit_mode. |
| */ |
| QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE = 38, |
| /* Used in QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT command |
| * to define the number of antennas to use for BRP. |
| * different purpose in each ANT_LIMIT_MODE: |
| * DISABLE - ignored |
| * EFFECTIVE - upper limit to number of antennas to be used |
| * FORCE - exact number of antennas to be used |
| * unsigned 8 bit value |
| */ |
| QCA_WLAN_VENDOR_ATTR_BRP_ANT_NUM_LIMIT = 39, |
| /* Used in QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI command |
| * to report the corresponding antenna index to the chain RSSI value |
| */ |
| QCA_WLAN_VENDOR_ATTR_ANTENNA_INFO = 40, |
| /* Used in QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI command to report |
| * the specific antenna EVM value (unsigned 32 bit value). With a |
| * determinate group of antennas, the driver specifies the EVM value |
| * for each antenna ID, and application extract them in user space. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CHAIN_EVM = 41, |
| /* |
| * Used in QCA_NL80211_VENDOR_SUBCMD_GET_FW_STATE command to report |
| * wlan firmware current state. FW state is an unsigned 8 bit value, |
| * one of the values in enum qca_wlan_vendor_attr_fw_state. |
| */ |
| QCA_WLAN_VENDOR_ATTR_FW_STATE = 42, |
| |
| /* Unsigned 32-bitmask value from enum qca_set_band. Substitutes the |
| * attribute QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE for which only a subset |
| * of single values from enum qca_set_band are valid. This attribute |
| * uses bitmask combinations to define the respective allowed band |
| * combinations and this attributes takes precedence over |
| * QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE if both attributes are included. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SETBAND_MASK = 43, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_MAX = QCA_WLAN_VENDOR_ATTR_AFTER_LAST - 1, |
| }; |
| |
| enum qca_roaming_policy { |
| QCA_ROAMING_NOT_ALLOWED, |
| QCA_ROAMING_ALLOWED_WITHIN_ESS, |
| }; |
| |
| /** |
| * enum qca_roam_reason - Represents the reason codes for roaming. Used by |
| * QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_REASON. |
| * |
| * @QCA_ROAM_REASON_UNKNOWN: Any reason that do not classify under the below |
| * reasons. |
| * |
| * @QCA_ROAM_REASON_PER: Roam triggered when packet error rates (PER) breached |
| * the configured threshold. |
| * |
| * @QCA_ROAM_REASON_BEACON_MISS: Roam triggered due to the continuous configured |
| * beacon misses from the then connected AP. |
| * |
| * @QCA_ROAM_REASON_POOR_RSSI: Roam triggered due to the poor RSSI reported |
| * by the connected AP. |
| * |
| * @QCA_ROAM_REASON_BETTER_RSSI: Roam triggered for finding a BSS with a better |
| * RSSI than the connected BSS. Here the RSSI of the current BSS is not poor. |
| * |
| * @QCA_ROAM_REASON_CONGESTION: Roam triggered considering the connected channel |
| * or environment being very noisy or congested. |
| * |
| * @QCA_ROAM_REASON_USER_TRIGGER: Roam triggered due to an explicit request |
| * from the user (user space). |
| * |
| * @QCA_ROAM_REASON_BTM: Roam triggered due to BTM Request frame received from |
| * the connected AP. |
| * |
| * @QCA_ROAM_REASON_BSS_LOAD: Roam triggered due to the channel utilization |
| * breaching out the configured threshold. |
| * |
| * @QCA_ROAM_REASON_WTC: Roam triggered due to Wireless to Cellular BSS |
| * transition request. |
| * |
| * @QCA_ROAM_REASON_IDLE: Roam triggered when device is suspended, there is no |
| * data activity with the AP and the current RSSI falls below a certain |
| * threshold. |
| * |
| * @QCA_ROAM_REASON_DISCONNECTION: Roam triggered due to Deauthentication or |
| * Disassociation frames received from the connected AP. |
| * |
| * @QCA_ROAM_REASON_PERIODIC_TIMER: Roam triggered as part of the periodic scan |
| * that happens when there is no candidate AP found during the poor RSSI scan |
| * trigger. |
| * |
| * @QCA_ROAM_REASON_BACKGROUND_SCAN: Roam triggered based on the scan results |
| * obtained from an external scan (not aimed at roaming). |
| * |
| * @QCA_ROAM_REASON_BT_ACTIVITY: Roam triggered due to Bluetooth connection is |
| * established when the station is connected in the 2.4 GHz band. |
| * |
| * @QCA_ROAM_REASON_STA_KICKOUT: Roam triggered due to continuous TX Data frame |
| * failures to the connected AP. |
| */ |
| enum qca_roam_reason { |
| QCA_ROAM_REASON_UNKNOWN, |
| QCA_ROAM_REASON_PER, |
| QCA_ROAM_REASON_BEACON_MISS, |
| QCA_ROAM_REASON_POOR_RSSI, |
| QCA_ROAM_REASON_BETTER_RSSI, |
| QCA_ROAM_REASON_CONGESTION, |
| QCA_ROAM_REASON_USER_TRIGGER, |
| QCA_ROAM_REASON_BTM, |
| QCA_ROAM_REASON_BSS_LOAD, |
| QCA_ROAM_REASON_WTC, |
| QCA_ROAM_REASON_IDLE, |
| QCA_ROAM_REASON_DISCONNECTION, |
| QCA_ROAM_REASON_PERIODIC_TIMER, |
| QCA_ROAM_REASON_BACKGROUND_SCAN, |
| QCA_ROAM_REASON_BT_ACTIVITY, |
| QCA_ROAM_REASON_STA_KICKOUT, |
| }; |
| |
| enum qca_wlan_vendor_attr_roam_auth { |
| QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_INVALID = 0, |
| /* Indicates BSSID of the roamed AP for non-MLO roaming and MLD address |
| * of the roamed AP for MLO roaming. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_BSSID, |
| QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_REQ_IE, |
| QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_RESP_IE, |
| QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_AUTHORIZED, |
| QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_KEY_REPLAY_CTR, |
| QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PTK_KCK, |
| QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PTK_KEK, |
| QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_SUBNET_STATUS, |
| /* Indicates the status of re-association requested by user space for |
| * the BSSID specified by QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_BSSID. |
| * Type u16. |
| * Represents the status code from AP. Use |
| * %WLAN_STATUS_UNSPECIFIED_FAILURE if the device cannot give you the |
| * real status code for failures. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_STATUS, |
| /* This attribute indicates that the old association was maintained when |
| * a re-association is requested by user space and that re-association |
| * attempt fails (i.e., cannot connect to the requested BSS, but can |
| * remain associated with the BSS with which the association was in |
| * place when being requested to roam). Used along with |
| * WLAN_VENDOR_ATTR_ROAM_AUTH_STATUS to indicate the current |
| * re-association status. Type flag. |
| * This attribute is applicable only for re-association failure cases. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_RETAIN_CONNECTION, |
| /* This attribute specifies the PMK if one was newly generated during |
| * FILS roaming. This is added to the PMKSA cache and is used in |
| * subsequent connections with PMKSA caching. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PMK = 11, |
| /* This attribute specifies the PMKID used/generated for the current |
| * FILS roam. This is used in subsequent connections with PMKSA caching. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PMKID = 12, |
| /* A 16-bit unsigned value specifying the next sequence number to use |
| * in ERP message in the currently associated realm. This is used in |
| * doing subsequent ERP based connections in the same realm. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_FILS_ERP_NEXT_SEQ_NUM = 13, |
| /* A 16-bit unsigned value representing the reasons for the roaming. |
| * Defined by enum qca_roam_reason. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_REASON = 14, |
| /* A nested attribute containing per-link information of all the links |
| * of MLO connection done while roaming. The attributes used inside this |
| * nested attribute are defined in enum qca_wlan_vendor_attr_mlo_links. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_MLO_LINKS = 15, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_MAX = |
| QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_AFTER_LAST - 1 |
| }; |
| |
| enum qca_wlan_vendor_attr_p2p_listen_offload { |
| QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_INVALID = 0, |
| /* A 32-bit unsigned value; the P2P listen frequency (MHz); must be one |
| * of the social channels. |
| */ |
| QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_CHANNEL, |
| /* A 32-bit unsigned value; the P2P listen offload period (ms). |
| */ |
| QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_PERIOD, |
| /* A 32-bit unsigned value; the P2P listen interval duration (ms). |
| */ |
| QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_INTERVAL, |
| /* A 32-bit unsigned value; number of interval times the firmware needs |
| * to run the offloaded P2P listen operation before it stops. |
| */ |
| QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_COUNT, |
| /* An array of arbitrary binary data with one or more 8-byte values. |
| * The device types include both primary and secondary device types. |
| */ |
| QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_DEVICE_TYPES, |
| /* An array of unsigned 8-bit characters; vendor information elements. |
| */ |
| QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_VENDOR_IE, |
| /* A 32-bit unsigned value; a control flag to indicate whether listen |
| * results need to be flushed to wpa_supplicant. |
| */ |
| QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_CTRL_FLAG, |
| /* A 8-bit unsigned value; reason code for P2P listen offload stop |
| * event. |
| */ |
| QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_STOP_REASON, |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_MAX = |
| QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_AFTER_LAST - 1 |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_acs_offload - Defines attributes to be used with |
| * vendor command/event QCA_NL80211_VENDOR_SUBCMD_DO_ACS. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_CHANNEL: Required (u8). |
| * Used with event to notify the primary channel number selected in ACS |
| * operation. |
| * Note: If both the driver and user-space application supports the 6 GHz band, |
| * QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_CHANNEL is deprecated; use |
| * QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_FREQUENCY instead. |
| * To maintain backward compatibility, QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_CHANNEL |
| * is still used if either of the driver or user space application doesn't |
| * support the 6 GHz band. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_CHANNEL: Required (u8). |
| * Used with event to notify the secondary channel number selected in ACS |
| * operation. |
| * Note: If both the driver and user-space application supports the 6 GHz band, |
| * QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_CHANNEL is deprecated; use |
| * QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_FREQUENCY instead. |
| * To maintain backward compatibility, |
| * QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_CHANNEL is still used if either of |
| * the driver or user space application doesn't support 6 GHz band. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ACS_HW_MODE: Required (u8). |
| * (a) Used with command to configure hw_mode from |
| * enum qca_wlan_vendor_acs_hw_mode for ACS operation. |
| * (b) Also used with event to notify the hw_mode of selected primary channel |
| * in ACS operation. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ACS_HT_ENABLED: Flag attribute. |
| * Used with command to configure ACS operation for HT mode. |
| * Disable (flag attribute not present) - HT disabled and |
| * Enable (flag attribute present) - HT enabled. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ACS_HT40_ENABLED: Flag attribute. |
| * Used with command to configure ACS operation for HT40 mode. |
| * Disable (flag attribute not present) - HT40 disabled and |
| * Enable (flag attribute present) - HT40 enabled. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ACS_VHT_ENABLED: Flag attribute. |
| * Used with command to configure ACS operation for VHT mode. |
| * Disable (flag attribute not present) - VHT disabled and |
| * Enable (flag attribute present) - VHT enabled. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ACS_CHWIDTH: Optional (u16) with command and |
| * mandatory with event. |
| * If specified in command path, ACS operation is configured with the given |
| * channel width (in MHz). |
| * In event path, specifies the channel width of the primary channel selected. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ACS_CH_LIST: Required and type is NLA_UNSPEC. |
| * Used with command to configure channel list using an array of |
| * channel numbers (u8). |
| * Note: If both the driver and user-space application supports the 6 GHz band, |
| * the driver mandates use of QCA_WLAN_VENDOR_ATTR_ACS_FREQ_LIST whereas |
| * QCA_WLAN_VENDOR_ATTR_ACS_CH_LIST is optional. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG0_CENTER_CHANNEL: Required (u8). |
| * Used with event to notify the VHT segment 0 center channel number selected in |
| * ACS operation. The value is the index of the channel center frequency for |
| * 20 MHz, 40 MHz, and 80 MHz channels. The value is the center frequency index |
| * of the primary 80 MHz segment for 160 MHz and 80+80 MHz channels. |
| * Note: If both the driver and user-space application supports the 6 GHz band, |
| * QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG0_CENTER_CHANNEL is deprecated; use |
| * QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG0_CENTER_FREQUENCY instead. |
| * To maintain backward compatibility, |
| * QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG0_CENTER_CHANNEL is still used if either of |
| * the driver or user space application doesn't support the 6 GHz band. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG1_CENTER_CHANNEL: Required (u8). |
| * Used with event to notify the VHT segment 1 center channel number selected in |
| * ACS operation. The value is zero for 20 MHz, 40 MHz, and 80 MHz channels. |
| * The value is the index of the channel center frequency for 160 MHz channels |
| * and the center frequency index of the secondary 80 MHz segment for 80+80 MHz |
| * channels. |
| * Note: If both the driver and user-space application supports the 6 GHz band, |
| * QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG1_CENTER_CHANNEL is deprecated; use |
| * QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG1_CENTER_FREQUENCY instead. |
| * To maintain backward compatibility, |
| * QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG1_CENTER_CHANNEL is still used if either of |
| * the driver or user space application doesn't support the 6 GHz band. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ACS_FREQ_LIST: Required and type is NLA_UNSPEC. |
| * Used with command to configure the channel list using an array of channel |
| * center frequencies in MHz (u32). |
| * Note: If both the driver and user-space application supports the 6 GHz band, |
| * the driver first parses the frequency list and if it fails to get a frequency |
| * list, parses the channel list specified using |
| * QCA_WLAN_VENDOR_ATTR_ACS_CH_LIST (considers only 2 GHz and 5 GHz channels in |
| * QCA_WLAN_VENDOR_ATTR_ACS_CH_LIST). |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_FREQUENCY: Required (u32). |
| * Used with event to notify the primary channel center frequency (MHz) selected |
| * in ACS operation. |
| * Note: If the driver supports the 6 GHz band, the event sent from the driver |
| * includes this attribute along with QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_CHANNEL. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_FREQUENCY: Required (u32). |
| * Used with event to notify the secondary channel center frequency (MHz) |
| * selected in ACS operation. |
| * Note: If the driver supports the 6 GHz band, the event sent from the driver |
| * includes this attribute along with |
| * QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_CHANNEL. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG0_CENTER_FREQUENCY: Required (u32). |
| * Used with event to notify the VHT segment 0 center channel frequency (MHz) |
| * selected in ACS operation. |
| * Note: If the driver supports the 6 GHz band, the event sent from the driver |
| * includes this attribute along with |
| * QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG0_CENTER_CHANNEL. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG1_CENTER_FREQUENCY: Required (u32). |
| * Used with event to notify the VHT segment 1 center channel frequency (MHz) |
| * selected in ACS operation. |
| * Note: If the driver supports the 6 GHz band, the event sent from the driver |
| * includes this attribute along with |
| * QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG1_CENTER_CHANNEL. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ACS_EDMG_ENABLED: Flag attribute. |
| * Used with command to notify the driver of EDMG request for ACS |
| * operation. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ACS_EDMG_CHANNEL: Optional (u8). |
| * Used with event to notify the EDMG channel number selected in ACS |
| * operation. |
| * EDMG primary channel is indicated by QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_CHANNEL |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ACS_PUNCTURE_BITMAP: Optional (u16). |
| * Used with event to notify the puncture pattern selected in ACS operation. |
| * Encoding for this attribute will follow the convention used in the Disabled |
| * Subchannel Bitmap field of the EHT Operation IE. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ACS_EHT_ENABLED: Flag attribute. |
| * Used with command to configure ACS operation for EHT mode. |
| * Disable (flag attribute not present) - EHT disabled and |
| * Enable (flag attribute present) - EHT enabled. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ACS_LAST_SCAN_AGEOUT_TIME: Optional (u32). |
| * Used with command to configure how older scan can be considered for ACS |
| * scoring. In case scan was performed on a partial set of channels configured |
| * with this command within last QCA_WLAN_VENDOR_ATTR_ACS_LAST_SCAN_AGEOUT_TIME |
| * (in ms), scan only the remaining channels. |
| */ |
| enum qca_wlan_vendor_attr_acs_offload { |
| QCA_WLAN_VENDOR_ATTR_ACS_CHANNEL_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_CHANNEL = 1, |
| QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_CHANNEL = 2, |
| QCA_WLAN_VENDOR_ATTR_ACS_HW_MODE = 3, |
| QCA_WLAN_VENDOR_ATTR_ACS_HT_ENABLED = 4, |
| QCA_WLAN_VENDOR_ATTR_ACS_HT40_ENABLED = 5, |
| QCA_WLAN_VENDOR_ATTR_ACS_VHT_ENABLED = 6, |
| QCA_WLAN_VENDOR_ATTR_ACS_CHWIDTH = 7, |
| QCA_WLAN_VENDOR_ATTR_ACS_CH_LIST = 8, |
| QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG0_CENTER_CHANNEL = 9, |
| QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG1_CENTER_CHANNEL = 10, |
| QCA_WLAN_VENDOR_ATTR_ACS_FREQ_LIST = 11, |
| QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_FREQUENCY = 12, |
| QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_FREQUENCY = 13, |
| QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG0_CENTER_FREQUENCY = 14, |
| QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG1_CENTER_FREQUENCY = 15, |
| QCA_WLAN_VENDOR_ATTR_ACS_EDMG_ENABLED = 16, |
| QCA_WLAN_VENDOR_ATTR_ACS_EDMG_CHANNEL = 17, |
| QCA_WLAN_VENDOR_ATTR_ACS_PUNCTURE_BITMAP = 18, |
| QCA_WLAN_VENDOR_ATTR_ACS_EHT_ENABLED = 19, |
| QCA_WLAN_VENDOR_ATTR_ACS_LAST_SCAN_AGEOUT_TIME = 20, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_ACS_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_ACS_MAX = |
| QCA_WLAN_VENDOR_ATTR_ACS_AFTER_LAST - 1 |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_acs_hw_mode - Defines HW mode to be used with the |
| * vendor command/event QCA_NL80211_VENDOR_SUBCMD_DO_ACS. |
| * |
| * @QCA_ACS_MODE_IEEE80211B: 802.11b mode |
| * @QCA_ACS_MODE_IEEE80211G: 802.11g mode |
| * @QCA_ACS_MODE_IEEE80211A: 802.11a mode |
| * @QCA_ACS_MODE_IEEE80211AD: 802.11ad mode |
| * @QCA_ACS_MODE_IEEE80211ANY: all modes |
| * @QCA_ACS_MODE_IEEE80211AX: 802.11ax mode |
| */ |
| enum qca_wlan_vendor_acs_hw_mode { |
| QCA_ACS_MODE_IEEE80211B, |
| QCA_ACS_MODE_IEEE80211G, |
| QCA_ACS_MODE_IEEE80211A, |
| QCA_ACS_MODE_IEEE80211AD, |
| QCA_ACS_MODE_IEEE80211ANY, |
| QCA_ACS_MODE_IEEE80211AX, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_features - Vendor device/driver feature flags |
| * |
| * @QCA_WLAN_VENDOR_FEATURE_KEY_MGMT_OFFLOAD: Device supports key |
| * management offload, a mechanism where the station's firmware |
| * does the exchange with the AP to establish the temporal keys |
| * after roaming, rather than having the user space wpa_supplicant do it. |
| * @QCA_WLAN_VENDOR_FEATURE_SUPPORT_HW_MODE_ANY: Device supports automatic |
| * band selection based on channel selection results. |
| * @QCA_WLAN_VENDOR_FEATURE_OFFCHANNEL_SIMULTANEOUS: Device supports |
| * simultaneous off-channel operations. |
| * @QCA_WLAN_VENDOR_FEATURE_P2P_LISTEN_OFFLOAD: Device supports P2P |
| * Listen offload; a mechanism where the station's firmware takes care of |
| * responding to incoming Probe Request frames received from other P2P |
| * Devices whilst in Listen state, rather than having the user space |
| * wpa_supplicant do it. Information from received P2P requests are |
| * forwarded from firmware to host whenever the host processor wakes up. |
| * @QCA_WLAN_VENDOR_FEATURE_OCE_STA: Device supports all OCE non-AP STA |
| * specific features. |
| * @QCA_WLAN_VENDOR_FEATURE_OCE_AP: Device supports all OCE AP specific |
| * features. |
| * @QCA_WLAN_VENDOR_FEATURE_OCE_STA_CFON: Device supports OCE STA-CFON |
| * specific features only. If a Device sets this bit but not the |
| * %QCA_WLAN_VENDOR_FEATURE_OCE_AP, the userspace shall assume that |
| * this Device may not support all OCE AP functionalities but can support |
| * only OCE STA-CFON functionalities. |
| * @QCA_WLAN_VENDOR_FEATURE_SELF_MANAGED_REGULATORY: Device supports self |
| * managed regulatory. |
| * @QCA_WLAN_VENDOR_FEATURE_TWT: Device supports TWT (Target Wake Time). |
| * @QCA_WLAN_VENDOR_FEATURE_11AX: Device supports 802.11ax (HE) |
| * @QCA_WLAN_VENDOR_FEATURE_6GHZ_SUPPORT: Device supports 6 GHz band operation |
| * @QCA_WLAN_VENDOR_FEATURE_THERMAL_CONFIG: Device is capable of receiving |
| * and applying thermal configuration through |
| * %QCA_WLAN_VENDOR_ATTR_THERMAL_LEVEL and |
| * %QCA_WLAN_VENDOR_ATTR_THERMAL_COMPLETION_WINDOW attributes from |
| * userspace. |
| * @QCA_WLAN_VENDOR_FEATURE_ADAPTIVE_11R: Device supports Adaptive 11r. |
| * With Adaptive 11r feature, access points advertise the vendor |
| * specific IEs and MDE but do not include FT AKM in the RSNE. |
| * The Adaptive 11r supported stations are expected to identify |
| * such vendor specific IEs and connect to the AP in FT mode though |
| * the profile is configured in non-FT mode. |
| * The driver-based SME cases also need to have this support for |
| * Adaptive 11r to handle the connection and roaming scenarios. |
| * This flag indicates the support for the same to the user space. |
| * @QCA_WLAN_VENDOR_FEATURE_CONCURRENT_BAND_SESSIONS: Device supports |
| * concurrent network sessions on different Wi-Fi bands. This feature |
| * capability is attributed to the hardware's capability to support |
| * the same (e.g., DBS). |
| * @QCA_WLAN_VENDOR_FEATURE_TWT_ASYNC_SUPPORT: Flag indicating whether the |
| * responses for the respective TWT operations are asynchronous (separate |
| * event message) from the driver. If not specified, the responses are |
| * synchronous (in vendor command reply) to the request. Each TWT |
| * operation is specifically mentioned (against its respective |
| * documentation) to support either of these or both modes. |
| * @QCA_WLAN_VENDOR_FEATURE_USE_ADD_DEL_VIRTUAL_INTF_FOR_NDI: Flag indicates |
| * that the driver requires add/del virtual interface path using the |
| * generic nl80211 commands for NDP interface create/delete and to |
| * register/unregister the netdev instead of creating/deleting the NDP |
| * interface using the vendor commands |
| * QCA_WLAN_VENDOR_ATTR_NDP_INTERFACE_CREATE and |
| * QCA_WLAN_VENDOR_ATTR_NDP_INTERFACE_DELETE. With the latest kernel |
| * (5.12 version onward), interface creation/deletion is not allowed using |
| * vendor commands as it leads to a deadlock while acquiring the RTNL_LOCK |
| * during the register/unregister of netdev. Create and delete NDP |
| * interface using NL80211_CMD_NEW_INTERFACE and NL80211_CMD_DEL_INTERFACE |
| * commands respectively if the driver advertises this capability set. |
| * @QCA_WLAN_VENDOR_FEATURE_SECURE_LTF_STA: Flag indicates that the device in |
| * station mode supports secure LTF. If NL80211_EXT_FEATURE_SECURE_LTF is |
| * set, then QCA_WLAN_VENDOR_FEATURE_SECURE_LTF_STA will be ignored. |
| * @QCA_WLAN_VENDOR_FEATURE_SECURE_LTF_AP: Flag indicates that the device in AP |
| * mode supports secure LTF. If NL80211_EXT_FEATURE_SECURE_LTF is set, then |
| * QCA_WLAN_VENDOR_FEATURE_SECURE_LTF_AP will be ignored. |
| * @QCA_WLAN_VENDOR_FEATURE_SECURE_RTT_STA: Flag indicates that the device in |
| * station mode supports secure RTT measurement exchange. If |
| * NL80211_EXT_FEATURE_SECURE_RTT is set, |
| * QCA_WLAN_VENDOR_FEATURE_SECURE_RTT_STA will be ignored. |
| * @QCA_WLAN_VENDOR_FEATURE_SECURE_RTT_AP: Flag indicates that the device in AP |
| * mode supports secure RTT measurement exchange. If |
| * NL80211_EXT_FEATURE_SECURE_RTT is set, |
| * QCA_WLAN_VENDOR_FEATURE_SECURE_RTT_AP will be ignored. |
| * @QCA_WLAN_VENDOR_FEATURE_PROT_RANGE_NEGO_AND_MEASURE_STA: Flag indicates that |
| * the device in station mode supports protection of range negotiation and |
| * measurement management frames. If |
| * NL80211_EXT_FEATURE_PROT_RANGE_NEGO_AND_MEASURE is set, then |
| * QCA_WLAN_VENDOR_FEATURE_PROT_RANGE_NEGO_AND_MEASURE_STA will be ignored. |
| * @QCA_WLAN_VENDOR_FEATURE_PROT_RANGE_NEGO_AND_MEASURE_AP: Flag indicates that |
| * the device in AP mode supports protection of range negotiation and |
| * measurement management frames. If |
| * NL80211_EXT_FEATURE_PROT_RANGE_NEGO_AND_MEASURE is set, then |
| * QCA_WLAN_VENDOR_FEATURE_PROT_RANGE_NEGO_AND_MEASURE_AP will be ignored. |
| * @QCA_WLAN_VENDOR_FEATURE_AP_ALLOWED_FREQ_LIST: Flag indicates that the device |
| * in AP mode supports configuring allowed frequency list for AP operation |
| * with %QCA_WLAN_VENDOR_ATTR_CONFIG_AP_ALLOWED_FREQ_LIST. |
| * @QCA_WLAN_VENDOR_FEATURE_ENHANCED_AUDIO_EXPERIENCE_OVER_WLAN: Flag indicates |
| * that the device supports enhanced audio experience over WLAN feature. |
| * @NUM_QCA_WLAN_VENDOR_FEATURES: Number of assigned feature bits |
| */ |
| enum qca_wlan_vendor_features { |
| QCA_WLAN_VENDOR_FEATURE_KEY_MGMT_OFFLOAD = 0, |
| QCA_WLAN_VENDOR_FEATURE_SUPPORT_HW_MODE_ANY = 1, |
| QCA_WLAN_VENDOR_FEATURE_OFFCHANNEL_SIMULTANEOUS = 2, |
| QCA_WLAN_VENDOR_FEATURE_P2P_LISTEN_OFFLOAD = 3, |
| QCA_WLAN_VENDOR_FEATURE_OCE_STA = 4, |
| QCA_WLAN_VENDOR_FEATURE_OCE_AP = 5, |
| QCA_WLAN_VENDOR_FEATURE_OCE_STA_CFON = 6, |
| QCA_WLAN_VENDOR_FEATURE_SELF_MANAGED_REGULATORY = 7, |
| QCA_WLAN_VENDOR_FEATURE_TWT = 8, |
| QCA_WLAN_VENDOR_FEATURE_11AX = 9, |
| QCA_WLAN_VENDOR_FEATURE_6GHZ_SUPPORT = 10, |
| QCA_WLAN_VENDOR_FEATURE_THERMAL_CONFIG = 11, |
| QCA_WLAN_VENDOR_FEATURE_ADAPTIVE_11R = 12, |
| QCA_WLAN_VENDOR_FEATURE_CONCURRENT_BAND_SESSIONS = 13, |
| QCA_WLAN_VENDOR_FEATURE_TWT_ASYNC_SUPPORT = 14, |
| QCA_WLAN_VENDOR_FEATURE_USE_ADD_DEL_VIRTUAL_INTF_FOR_NDI = 15, |
| QCA_WLAN_VENDOR_FEATURE_SECURE_LTF_STA = 16, |
| QCA_WLAN_VENDOR_FEATURE_SECURE_LTF_AP = 17, |
| QCA_WLAN_VENDOR_FEATURE_SECURE_RTT_STA = 18, |
| QCA_WLAN_VENDOR_FEATURE_SECURE_RTT_AP = 19, |
| QCA_WLAN_VENDOR_FEATURE_PROT_RANGE_NEGO_AND_MEASURE_STA = 20, |
| QCA_WLAN_VENDOR_FEATURE_PROT_RANGE_NEGO_AND_MEASURE_AP = 21, |
| QCA_WLAN_VENDOR_FEATURE_AP_ALLOWED_FREQ_LIST = 22, |
| QCA_WLAN_VENDOR_FEATURE_ENHANCED_AUDIO_EXPERIENCE_OVER_WLAN = 23, |
| NUM_QCA_WLAN_VENDOR_FEATURES /* keep last */ |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_data_offload_ind - Vendor Data Offload Indication |
| * |
| * @QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_SESSION: Session corresponding to |
| * the offloaded data. |
| * @QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_PROTOCOL: Protocol of the offloaded |
| * data. |
| * @QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_EVENT: Event type for the data offload |
| * indication. |
| */ |
| enum qca_wlan_vendor_attr_data_offload_ind { |
| QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_SESSION, |
| QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_PROTOCOL, |
| QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_EVENT, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_MAX = |
| QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_AFTER_LAST - 1 |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_ocb_set_config - Vendor subcmd attributes to set |
| * OCB config |
| * |
| * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_CHANNEL_COUNT: Number of channels in the |
| * configuration |
| * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_SCHEDULE_SIZE: Size of the schedule |
| * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_CHANNEL_ARRAY: Array of channels |
| * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_SCHEDULE_ARRAY: Array of channels to be |
| * scheduled |
| * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_NDL_CHANNEL_ARRAY: Array of NDL channel |
| * information |
| * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_NDL_ACTIVE_STATE_ARRAY: Array of NDL |
| * active state configuration |
| * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_FLAGS: Configuration flags such as |
| * OCB_CONFIG_FLAG_80211_FRAME_MODE |
| * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_DEF_TX_PARAM: Default TX parameters to |
| * use in the case that a packet is sent without a TX control header |
| * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_TA_MAX_DURATION: Max duration after the |
| * last TA received that the local time set by TA is synchronous to other |
| * communicating OCB STAs. |
| */ |
| enum qca_wlan_vendor_attr_ocb_set_config { |
| QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_CHANNEL_COUNT = 1, |
| QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_SCHEDULE_SIZE = 2, |
| QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_CHANNEL_ARRAY = 3, |
| QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_SCHEDULE_ARRAY = 4, |
| QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_NDL_CHANNEL_ARRAY = 5, |
| QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_NDL_ACTIVE_STATE_ARRAY = 6, |
| QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_FLAGS = 7, |
| QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_DEF_TX_PARAM = 8, |
| QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_TA_MAX_DURATION = 9, |
| QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_MAX = |
| QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_AFTER_LAST - 1 |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_ocb_set_utc_time - Vendor subcmd attributes to set |
| * UTC time |
| * |
| * @QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_VALUE: The UTC time as an array of |
| * 10 bytes |
| * @QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_ERROR: The time error as an array of |
| * 5 bytes |
| */ |
| enum qca_wlan_vendor_attr_ocb_set_utc_time { |
| QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_VALUE = 1, |
| QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_ERROR = 2, |
| QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_MAX = |
| QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_AFTER_LAST - 1 |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_ocb_start_timing_advert - Vendor subcmd attributes |
| * to start sending timing advert frames |
| * |
| * @QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_CHANNEL_FREQ: Cannel frequency |
| * on which to send the frames |
| * @QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_REPEAT_RATE: Number of times |
| * the frame is sent in 5 seconds |
| */ |
| enum qca_wlan_vendor_attr_ocb_start_timing_advert { |
| QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_CHANNEL_FREQ = 1, |
| QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_REPEAT_RATE = 2, |
| QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_MAX = |
| QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_AFTER_LAST - 1 |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_ocb_stop_timing_advert - Vendor subcmd attributes |
| * to stop timing advert |
| * |
| * @QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_CHANNEL_FREQ: The channel |
| * frequency on which to stop the timing advert |
| */ |
| enum qca_wlan_vendor_attr_ocb_stop_timing_advert { |
| QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_CHANNEL_FREQ = 1, |
| QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_MAX = |
| QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_AFTER_LAST - 1 |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_ocb_get_tsf_response - Vendor subcmd attributes to |
| * get TSF timer value |
| * |
| * @QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_TIMER_HIGH: Higher 32 bits of the |
| * timer |
| * @QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_TIMER_LOW: Lower 32 bits of the timer |
| */ |
| enum qca_wlan_vendor_attr_ocb_get_tsf_resp { |
| QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_TIMER_HIGH = 1, |
| QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_TIMER_LOW = 2, |
| QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_MAX = |
| QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_AFTER_LAST - 1 |
| }; |
| |
| enum qca_vendor_attr_get_preferred_freq_list { |
| QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_INVALID, |
| /* A 32-unsigned value; the interface type/mode for which the preferred |
| * frequency list is requested (see enum qca_iface_type for possible |
| * values); used in GET_PREFERRED_FREQ_LIST command from user-space to |
| * kernel and in the kernel response back to user-space. |
| */ |
| QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_IFACE_TYPE, |
| /* An array of 32-unsigned values; values are frequency (MHz); sent |
| * from kernel space to user space. |
| */ |
| QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST, |
| /* An array of nested values as per enum qca_wlan_vendor_attr_pcl |
| * attribute. Each element contains frequency (MHz), weight, and flag |
| * bit mask indicating how the frequency should be used in P2P |
| * negotiation; sent from kernel space to user space. |
| */ |
| QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_WEIGHED_PCL, |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_MAX = |
| QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_AFTER_LAST - 1 |
| }; |
| |
| enum qca_vendor_attr_probable_oper_channel { |
| QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_INVALID, |
| /* 32-bit unsigned value; indicates the connection/iface type likely to |
| * come on this channel (see enum qca_iface_type). |
| */ |
| QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_IFACE_TYPE, |
| /* 32-bit unsigned value; the frequency (MHz) of the probable channel */ |
| QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_FREQ, |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_MAX = |
| QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_AFTER_LAST - 1 |
| }; |
| |
| enum qca_iface_type { |
| QCA_IFACE_TYPE_STA, |
| QCA_IFACE_TYPE_AP, |
| QCA_IFACE_TYPE_P2P_CLIENT, |
| QCA_IFACE_TYPE_P2P_GO, |
| QCA_IFACE_TYPE_IBSS, |
| QCA_IFACE_TYPE_TDLS, |
| }; |
| |
| enum qca_set_band { |
| QCA_SETBAND_AUTO = 0, |
| QCA_SETBAND_5G = BIT(0), |
| QCA_SETBAND_2G = BIT(1), |
| QCA_SETBAND_6G = BIT(2), |
| }; |
| |
| /** |
| * enum qca_access_policy - Access control policy |
| * |
| * Access control policy is applied on the configured IE |
| * (QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE). |
| * To be set with QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY. |
| * |
| * @QCA_ACCESS_POLICY_ACCEPT_UNLESS_LISTED: Deny Wi-Fi connections which match |
| * the specific configuration (IE) set, i.e., allow all the |
| * connections which do not match the configuration. |
| * @QCA_ACCESS_POLICY_DENY_UNLESS_LISTED: Accept Wi-Fi connections which match |
| * the specific configuration (IE) set, i.e., deny all the |
| * connections which do not match the configuration. |
| */ |
| enum qca_access_policy { |
| QCA_ACCESS_POLICY_ACCEPT_UNLESS_LISTED, |
| QCA_ACCESS_POLICY_DENY_UNLESS_LISTED, |
| }; |
| |
| /** |
| * enum qca_vendor_attr_tsf_cmd: Vendor attributes for TSF capture |
| * @QCA_WLAN_VENDOR_ATTR_TSF_CMD: Required (u32) |
| * Specify the TSF command. Possible values are defined in |
| * &enum qca_tsf_cmd. |
| * @QCA_WLAN_VENDOR_ATTR_TSF_TIMER_VALUE: Optional (u64) |
| * This attribute contains TSF timer value. This attribute is only available |
| * in %QCA_TSF_GET or %QCA_TSF_SYNC_GET response. |
| * @QCA_WLAN_VENDOR_ATTR_TSF_SOC_TIMER_VALUE: Optional (u64) |
| * This attribute contains SOC timer value at TSF capture. This attribute is |
| * only available in %QCA_TSF_GET or %QCA_TSF_SYNC_GET response. |
| * @QCA_WLAN_VENDOR_ATTR_TSF_SYNC_INTERVAL: Optional (u32) |
| * This attribute is used to provide TSF sync interval and only applicable when |
| * TSF command is %QCA_TSF_SYNC_START. If this attribute is not provided, the |
| * driver will use the default value. Time unit is in milliseconds. |
| * @QCA_WLAN_VENDOR_ATTR_TSF_PAD: Attribute used for padding for 64-bit |
| * alignment. |
| */ |
| enum qca_vendor_attr_tsf_cmd { |
| QCA_WLAN_VENDOR_ATTR_TSF_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_TSF_CMD, |
| QCA_WLAN_VENDOR_ATTR_TSF_TIMER_VALUE, |
| QCA_WLAN_VENDOR_ATTR_TSF_SOC_TIMER_VALUE, |
| QCA_WLAN_VENDOR_ATTR_TSF_SYNC_INTERVAL, |
| QCA_WLAN_VENDOR_ATTR_TSF_PAD, |
| QCA_WLAN_VENDOR_ATTR_TSF_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_TSF_MAX = |
| QCA_WLAN_VENDOR_ATTR_TSF_AFTER_LAST - 1 |
| }; |
| |
| /** |
| * enum qca_tsf_cmd: TSF driver commands |
| * @QCA_TSF_CAPTURE: Initiate TSF Capture |
| * @QCA_TSF_GET: Get TSF capture value |
| * @QCA_TSF_SYNC_GET: Initiate TSF capture and return with captured value |
| * @QCA_TSF_AUTO_REPORT_ENABLE: Used in STA mode only. Once set, the target |
| * will automatically send TSF report to the host. To query |
| * %QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_UPLINK_DELAY, this operation needs to be |
| * initiated first. |
| * @QCA_TSF_AUTO_REPORT_DISABLE: Used in STA mode only. Once set, the target |
| * will not automatically send TSF report to the host. If |
| * %QCA_TSF_AUTO_REPORT_ENABLE is initiated and |
| * %QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_UPLINK_DELAY is not queried anymore, this |
| * operation needs to be initiated. |
| * @QCA_TSF_SYNC_START: Start periodic TSF sync feature. The driver periodically |
| * fetches TSF and host time mapping from the firmware with interval configured |
| * through the %QCA_WLAN_VENDOR_ATTR_TSF_SYNC_INTERVAL attribute. If the |
| * interval value is not provided the driver will use the default value. The |
| * userspace can query the TSF and host time mapping via the %QCA_TSF_GET |
| * command. |
| * @QCA_TSF_SYNC_STOP: Stop periodic TSF sync feature. |
| */ |
| enum qca_tsf_cmd { |
| QCA_TSF_CAPTURE, |
| QCA_TSF_GET, |
| QCA_TSF_SYNC_GET, |
| QCA_TSF_AUTO_REPORT_ENABLE, |
| QCA_TSF_AUTO_REPORT_DISABLE, |
| QCA_TSF_SYNC_START, |
| QCA_TSF_SYNC_STOP, |
| }; |
| |
| /** |
| * enum qca_vendor_attr_wisa_cmd |
| * @QCA_WLAN_VENDOR_ATTR_WISA_MODE: WISA mode value (u32) |
| * WISA setup vendor commands |
| */ |
| enum qca_vendor_attr_wisa_cmd { |
| QCA_WLAN_VENDOR_ATTR_WISA_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_WISA_MODE, |
| QCA_WLAN_VENDOR_ATTR_WISA_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_WISA_MAX = |
| QCA_WLAN_VENDOR_ATTR_WISA_AFTER_LAST - 1 |
| }; |
| |
| /* IEEE 802.11 Vendor Specific elements */ |
| |
| /** |
| * enum qca_vendor_element_id - QCA Vendor Specific element types |
| * |
| * These values are used to identify QCA Vendor Specific elements. The |
| * payload of the element starts with the three octet OUI (OUI_QCA) and |
| * is followed by a single octet type which is defined by this enum. |
| * |
| * @QCA_VENDOR_ELEM_P2P_PREF_CHAN_LIST: P2P preferred channel list. |
| * This element can be used to specify preference order for supported |
| * channels. The channels in this list are in preference order (the first |
| * one has the highest preference) and are described as a pair of |
| * (global) Operating Class and Channel Number (each one octet) fields. |
| * |
| * This extends the standard P2P functionality by providing option to have |
| * more than one preferred operating channel. When this element is present, |
| * it replaces the preference indicated in the Operating Channel attribute. |
| * For supporting other implementations, the Operating Channel attribute is |
| * expected to be used with the highest preference channel. Similarly, all |
| * the channels included in this Preferred channel list element are |
| * expected to be included in the Channel List attribute. |
| * |
| * This vendor element may be included in GO Negotiation Request, P2P |
| * Invitation Request, and Provision Discovery Request frames. |
| * |
| * @QCA_VENDOR_ELEM_HE_CAPAB: HE Capabilities element. |
| * This element can be used for pre-standard publication testing of HE |
| * before P802.11ax draft assigns the element ID. The payload of this |
| * vendor specific element is defined by the latest P802.11ax draft. |
| * Please note that the draft is still work in progress and this element |
| * payload is subject to change. |
| * |
| * @QCA_VENDOR_ELEM_HE_OPER: HE Operation element. |
| * This element can be used for pre-standard publication testing of HE |
| * before P802.11ax draft assigns the element ID. The payload of this |
| * vendor specific element is defined by the latest P802.11ax draft. |
| * Please note that the draft is still work in progress and this element |
| * payload is subject to change. |
| * |
| * @QCA_VENDOR_ELEM_RAPS: RAPS element (OFDMA-based Random Access Parameter Set |
| * element). |
| * This element can be used for pre-standard publication testing of HE |
| * before P802.11ax draft assigns the element ID extension. The payload of |
| * this vendor specific element is defined by the latest P802.11ax draft |
| * (not including the Element ID Extension field). Please note that the |
| * draft is still work in progress and this element payload is subject to |
| * change. |
| * |
| * @QCA_VENDOR_ELEM_MU_EDCA_PARAMS: MU EDCA Parameter Set element. |
| * This element can be used for pre-standard publication testing of HE |
| * before P802.11ax draft assigns the element ID extension. The payload of |
| * this vendor specific element is defined by the latest P802.11ax draft |
| * (not including the Element ID Extension field). Please note that the |
| * draft is still work in progress and this element payload is subject to |
| * change. |
| * |
| * @QCA_VENDOR_ELEM_BSS_COLOR_CHANGE: BSS Color Change Announcement element. |
| * This element can be used for pre-standard publication testing of HE |
| * before P802.11ax draft assigns the element ID extension. The payload of |
| * this vendor specific element is defined by the latest P802.11ax draft |
| * (not including the Element ID Extension field). Please note that the |
| * draft is still work in progress and this element payload is subject to |
| * change. |
| * |
| * @QCA_VENDOR_ELEM_ALLPLAY: Allplay element |
| */ |
| enum qca_vendor_element_id { |
| QCA_VENDOR_ELEM_P2P_PREF_CHAN_LIST = 0, |
| QCA_VENDOR_ELEM_HE_CAPAB = 1, |
| QCA_VENDOR_ELEM_HE_OPER = 2, |
| QCA_VENDOR_ELEM_RAPS = 3, |
| QCA_VENDOR_ELEM_MU_EDCA_PARAMS = 4, |
| QCA_VENDOR_ELEM_BSS_COLOR_CHANGE = 5, |
| QCA_VENDOR_ELEM_ALLPLAY = 6, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_scan_priority - Specifies the valid values that the |
| * vendor scan attribute QCA_WLAN_VENDOR_ATTR_SCAN_PRIORITY can take. |
| * @QCA_WLAN_VENDOR_SCAN_PRIORITY_VERY_LOW: Very low priority |
| * @QCA_WLAN_VENDOR_SCAN_PRIORITY_LOW: Low priority |
| * @QCA_WLAN_VENDOR_SCAN_PRIORITY_MEDIUM: Medium priority |
| * @QCA_WLAN_VENDOR_SCAN_PRIORITY_HIGH: High priority |
| * @QCA_WLAN_VENDOR_SCAN_PRIORITY_VERY_HIGH: Very high priority |
| */ |
| enum qca_wlan_vendor_scan_priority { |
| QCA_WLAN_VENDOR_SCAN_PRIORITY_VERY_LOW = 0, |
| QCA_WLAN_VENDOR_SCAN_PRIORITY_LOW = 1, |
| QCA_WLAN_VENDOR_SCAN_PRIORITY_MEDIUM = 2, |
| QCA_WLAN_VENDOR_SCAN_PRIORITY_HIGH = 3, |
| QCA_WLAN_VENDOR_SCAN_PRIORITY_VERY_HIGH = 4, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_scan - Specifies vendor scan attributes |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SCAN_IE: IEs that should be included as part of scan |
| * @QCA_WLAN_VENDOR_ATTR_SCAN_FREQUENCIES: Nested unsigned 32-bit attributes |
| * with frequencies to be scanned (in MHz) |
| * @QCA_WLAN_VENDOR_ATTR_SCAN_SSIDS: Nested attribute with SSIDs to be scanned |
| * @QCA_WLAN_VENDOR_ATTR_SCAN_SUPP_RATES: Nested array attribute of supported |
| * rates to be included |
| * @QCA_WLAN_VENDOR_ATTR_SCAN_TX_NO_CCK_RATE: flag used to send probe requests |
| * at non CCK rate in 2GHz band |
| * @QCA_WLAN_VENDOR_ATTR_SCAN_FLAGS: Unsigned 32-bit scan flags |
| * @QCA_WLAN_VENDOR_ATTR_SCAN_COOKIE: Unsigned 64-bit cookie provided by the |
| * driver for the specific scan request |
| * @QCA_WLAN_VENDOR_ATTR_SCAN_STATUS: Unsigned 8-bit status of the scan |
| * request decoded as in enum scan_status |
| * @QCA_WLAN_VENDOR_ATTR_SCAN_MAC: 6-byte MAC address to use when randomisation |
| * scan flag is set |
| * @QCA_WLAN_VENDOR_ATTR_SCAN_MAC_MASK: 6-byte MAC address mask to be used with |
| * randomisation |
| * @QCA_WLAN_VENDOR_ATTR_SCAN_BSSID: 6-byte MAC address representing the |
| * specific BSSID to scan for. |
| * @QCA_WLAN_VENDOR_ATTR_SCAN_DWELL_TIME: Unsigned 64-bit dwell time in |
| * microseconds. This is a common value which applies across all |
| * frequencies specified by QCA_WLAN_VENDOR_ATTR_SCAN_FREQUENCIES. |
| * @QCA_WLAN_VENDOR_ATTR_SCAN_PRIORITY: Priority of vendor scan relative to |
| * other scan requests. It is a u32 attribute and takes values from enum |
| * qca_wlan_vendor_scan_priority. This is an optional attribute. |
| * If this attribute is not configured, the driver shall use |
| * QCA_WLAN_VENDOR_SCAN_PRIORITY_HIGH as the priority of vendor scan. |
| * @QCA_WLAN_VENDOR_ATTR_SCAN_PAD: Attribute used for padding for 64-bit |
| * alignment. |
| */ |
| enum qca_wlan_vendor_attr_scan { |
| QCA_WLAN_VENDOR_ATTR_SCAN_INVALID_PARAM = 0, |
| QCA_WLAN_VENDOR_ATTR_SCAN_IE = 1, |
| QCA_WLAN_VENDOR_ATTR_SCAN_FREQUENCIES = 2, |
| QCA_WLAN_VENDOR_ATTR_SCAN_SSIDS = 3, |
| QCA_WLAN_VENDOR_ATTR_SCAN_SUPP_RATES = 4, |
| QCA_WLAN_VENDOR_ATTR_SCAN_TX_NO_CCK_RATE = 5, |
| QCA_WLAN_VENDOR_ATTR_SCAN_FLAGS = 6, |
| QCA_WLAN_VENDOR_ATTR_SCAN_COOKIE = 7, |
| QCA_WLAN_VENDOR_ATTR_SCAN_STATUS = 8, |
| QCA_WLAN_VENDOR_ATTR_SCAN_MAC = 9, |
| QCA_WLAN_VENDOR_ATTR_SCAN_MAC_MASK = 10, |
| QCA_WLAN_VENDOR_ATTR_SCAN_BSSID = 11, |
| QCA_WLAN_VENDOR_ATTR_SCAN_DWELL_TIME = 12, |
| QCA_WLAN_VENDOR_ATTR_SCAN_PRIORITY = 13, |
| QCA_WLAN_VENDOR_ATTR_SCAN_PAD = 14, |
| QCA_WLAN_VENDOR_ATTR_SCAN_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_SCAN_MAX = |
| QCA_WLAN_VENDOR_ATTR_SCAN_AFTER_LAST - 1 |
| }; |
| |
| /** |
| * enum scan_status - Specifies the valid values the vendor scan attribute |
| * QCA_WLAN_VENDOR_ATTR_SCAN_STATUS can take |
| * |
| * @VENDOR_SCAN_STATUS_NEW_RESULTS: implies the vendor scan is successful with |
| * new scan results |
| * @VENDOR_SCAN_STATUS_ABORTED: implies the vendor scan was aborted in-between |
| */ |
| enum scan_status { |
| VENDOR_SCAN_STATUS_NEW_RESULTS, |
| VENDOR_SCAN_STATUS_ABORTED, |
| VENDOR_SCAN_STATUS_MAX, |
| }; |
| |
| /** |
| * enum qca_vendor_attr_ota_test - Specifies the values for vendor |
| * command QCA_NL80211_VENDOR_SUBCMD_OTA_TEST |
| * @QCA_WLAN_VENDOR_ATTR_OTA_TEST_ENABLE: enable ota test |
| */ |
| enum qca_vendor_attr_ota_test { |
| QCA_WLAN_VENDOR_ATTR_OTA_TEST_INVALID, |
| /* 8-bit unsigned value to indicate if OTA test is enabled */ |
| QCA_WLAN_VENDOR_ATTR_OTA_TEST_ENABLE, |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_OTA_TEST_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_OTA_TEST_MAX = |
| QCA_WLAN_VENDOR_ATTR_OTA_TEST_AFTER_LAST - 1 |
| }; |
| |
| /** |
| * enum qca_vendor_attr_txpower_scale - vendor sub commands index |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE: scaling value |
| */ |
| enum qca_vendor_attr_txpower_scale { |
| QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_INVALID, |
| /* 8-bit unsigned value to indicate the scaling of tx power */ |
| QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE, |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_MAX = |
| QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_AFTER_LAST - 1 |
| }; |
| |
| /** |
| * enum qca_vendor_attr_txpower_decr_db - Attributes for TX power decrease |
| * |
| * These attributes are used with QCA_NL80211_VENDOR_SUBCMD_SET_TXPOWER_DECR_DB. |
| */ |
| enum qca_vendor_attr_txpower_decr_db { |
| QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_INVALID, |
| /* 8-bit unsigned value to indicate the reduction of TX power in dB for |
| * a virtual interface. |
| */ |
| QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB, |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_MAX = |
| QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_AFTER_LAST - 1 |
| }; |
| |
| /* Attributes for data used by |
| * QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION and |
| * QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION subcommands. |
| */ |
| enum qca_wlan_vendor_attr_config { |
| QCA_WLAN_VENDOR_ATTR_CONFIG_INVALID = 0, |
| /* Unsigned 32-bit value to set the DTIM period. |
| * Whether the wifi chipset wakes at every dtim beacon or a multiple of |
| * the DTIM period. If DTIM is set to 3, the STA shall wake up every 3 |
| * DTIM beacons. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_DYNAMIC_DTIM = 1, |
| /* Unsigned 32-bit value to set the wifi_iface stats averaging factor |
| * used to calculate statistics like average the TSF offset or average |
| * number of frame leaked. |
| * For instance, upon Beacon frame reception: |
| * current_avg = ((beacon_TSF - TBTT) * factor + previous_avg * (0x10000 - factor) ) / 0x10000 |
| * For instance, when evaluating leaky APs: |
| * current_avg = ((num frame received within guard time) * factor + previous_avg * (0x10000 - factor)) / 0x10000 |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_STATS_AVG_FACTOR = 2, |
| /* Unsigned 32-bit value to configure guard time, i.e., when |
| * implementing IEEE power management based on frame control PM bit, how |
| * long the driver waits before shutting down the radio and after |
| * receiving an ACK frame for a Data frame with PM bit set. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_GUARD_TIME = 3, |
| /* Unsigned 32-bit value to change the FTM capability dynamically */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_FINE_TIME_MEASUREMENT = 4, |
| /* Unsigned 16-bit value to configure maximum TX rate dynamically */ |
| QCA_WLAN_VENDOR_ATTR_CONF_TX_RATE = 5, |
| /* Unsigned 32-bit value to configure the number of continuous |
| * Beacon Miss which shall be used by the firmware to penalize |
| * the RSSI. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_PENALIZE_AFTER_NCONS_BEACON_MISS = 6, |
| /* Unsigned 8-bit value to configure the channel avoidance indication |
| * behavior. Firmware to send only one indication and ignore duplicate |
| * indications when set to avoid multiple Apps wakeups. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_CHANNEL_AVOIDANCE_IND = 7, |
| /* 8-bit unsigned value to configure the maximum TX MPDU for |
| * aggregation. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_TX_MPDU_AGGREGATION = 8, |
| /* 8-bit unsigned value to configure the maximum RX MPDU for |
| * aggregation. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_RX_MPDU_AGGREGATION = 9, |
| /* 8-bit unsigned value to configure the Non aggregrate/11g sw |
| * retry threshold (0 disable, 31 max). |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_NON_AGG_RETRY = 10, |
| /* 8-bit unsigned value to configure the aggregrate sw |
| * retry threshold (0 disable, 31 max). |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_AGG_RETRY = 11, |
| /* 8-bit unsigned value to configure the MGMT frame |
| * retry threshold (0 disable, 31 max). |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_MGMT_RETRY = 12, |
| /* 8-bit unsigned value to configure the CTRL frame |
| * retry threshold (0 disable, 31 max). |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_CTRL_RETRY = 13, |
| /* 8-bit unsigned value to configure the propagation delay for |
| * 2G/5G band (0~63, units in us) |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_PROPAGATION_DELAY = 14, |
| /* Unsigned 32-bit value to configure the number of unicast TX fail |
| * packet count. The peer is disconnected once this threshold is |
| * reached. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_TX_FAIL_COUNT = 15, |
| /* Attribute used to set scan default IEs to the driver. |
| * |
| * These IEs can be used by scan operations that will be initiated by |
| * the driver/firmware. |
| * |
| * For further scan requests coming to the driver, these IEs should be |
| * merged with the IEs received along with scan request coming to the |
| * driver. If a particular IE is present in the scan default IEs but not |
| * present in the scan request, then that IE should be added to the IEs |
| * sent in the Probe Request frames for that scan request. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_SCAN_DEFAULT_IES = 16, |
| /* Unsigned 32-bit attribute for generic commands */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_COMMAND = 17, |
| /* Unsigned 32-bit value attribute for generic commands */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_VALUE = 18, |
| /* Unsigned 32-bit data attribute for generic command response */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA = 19, |
| /* Unsigned 32-bit length attribute for |
| * QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_LENGTH = 20, |
| /* Unsigned 32-bit flags attribute for |
| * QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_FLAGS = 21, |
| /* Unsigned 32-bit, defining the access policy. |
| * See enum qca_access_policy. Used with |
| * QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE_LIST. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY = 22, |
| /* Sets the list of full set of IEs for which a specific access policy |
| * has to be applied. Used along with |
| * QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY to control the access. |
| * Zero length payload can be used to clear this access constraint. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE_LIST = 23, |
| /* Unsigned 32-bit, specifies the interface index (netdev) for which the |
| * corresponding configurations are applied. If the interface index is |
| * not specified, the configurations are attributed to the respective |
| * wiphy. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_IFINDEX = 24, |
| /* 8-bit unsigned value to trigger QPower: 1-Enable, 0-Disable */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_QPOWER = 25, |
| /* 8-bit unsigned value to configure the driver and below layers to |
| * ignore the assoc disallowed set by APs while connecting |
| * 1-Ignore, 0-Don't ignore |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_IGNORE_ASSOC_DISALLOWED = 26, |
| /* 32-bit unsigned value to trigger antenna diversity features: |
| * 1-Enable, 0-Disable |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_ENA = 27, |
| /* 32-bit unsigned value to configure specific chain antenna */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_CHAIN = 28, |
| /* 32-bit unsigned value to trigger cycle selftest |
| * 1-Enable, 0-Disable |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_SELFTEST = 29, |
| /* 32-bit unsigned to configure the cycle time of selftest |
| * the unit is micro-second |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_SELFTEST_INTVL = 30, |
| /* 32-bit unsigned value to set reorder timeout for AC_VO */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_RX_REORDER_TIMEOUT_VOICE = 31, |
| /* 32-bit unsigned value to set reorder timeout for AC_VI */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_RX_REORDER_TIMEOUT_VIDEO = 32, |
| /* 32-bit unsigned value to set reorder timeout for AC_BE */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_RX_REORDER_TIMEOUT_BESTEFFORT = 33, |
| /* 32-bit unsigned value to set reorder timeout for AC_BK */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_RX_REORDER_TIMEOUT_BACKGROUND = 34, |
| /* 6-byte MAC address to point out the specific peer */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_RX_BLOCKSIZE_PEER_MAC = 35, |
| /* 32-bit unsigned value to set window size for specific peer */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_RX_BLOCKSIZE_WINLIMIT = 36, |
| /* 8-bit unsigned value to set the beacon miss threshold in 2.4 GHz */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_BEACON_MISS_THRESHOLD_24 = 37, |
| /* 8-bit unsigned value to set the beacon miss threshold in 5 GHz */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_BEACON_MISS_THRESHOLD_5 = 38, |
| /* 32-bit unsigned value to configure 5 or 10 MHz channel width for |
| * station device while in disconnect state. The attribute use the |
| * value of enum nl80211_chan_width: NL80211_CHAN_WIDTH_5 means 5 MHz, |
| * NL80211_CHAN_WIDTH_10 means 10 MHz. If set, the device work in 5 or |
| * 10 MHz channel width, the station will not connect to a BSS using 20 |
| * MHz or higher bandwidth. Set to NL80211_CHAN_WIDTH_20_NOHT to |
| * clear this constraint. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_SUB20_CHAN_WIDTH = 39, |
| /* 32-bit unsigned value to configure the propagation absolute delay |
| * for 2G/5G band (units in us) |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_PROPAGATION_ABS_DELAY = 40, |
| /* 32-bit unsigned value to set probe period */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_PROBE_PERIOD = 41, |
| /* 32-bit unsigned value to set stay period */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_STAY_PERIOD = 42, |
| /* 32-bit unsigned value to set snr diff */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_SNR_DIFF = 43, |
| /* 32-bit unsigned value to set probe dwell time */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_PROBE_DWELL_TIME = 44, |
| /* 32-bit unsigned value to set mgmt snr weight */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_MGMT_SNR_WEIGHT = 45, |
| /* 32-bit unsigned value to set data snr weight */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_DATA_SNR_WEIGHT = 46, |
| /* 32-bit unsigned value to set ack snr weight */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_ACK_SNR_WEIGHT = 47, |
| /* 32-bit unsigned value to configure the listen interval. |
| * This is in units of beacon intervals. This configuration alters |
| * the negotiated listen interval with the AP during the connection. |
| * It is highly recommended to configure a value less than or equal to |
| * the one negotiated during the association. Configuring any greater |
| * value can have adverse effects (frame loss, AP disassociating STA, |
| * etc.). |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_LISTEN_INTERVAL = 48, |
| /* |
| * 8 bit unsigned value that is set on an AP/GO virtual interface to |
| * disable operations that would cause the AP/GO to leave its operating |
| * channel. |
| * |
| * This will restrict the scans to the AP/GO operating channel and the |
| * channels of the other band, if DBS is supported.A STA/CLI interface |
| * brought up after this setting is enabled, will be restricted to |
| * connecting to devices only on the AP/GO interface's operating channel |
| * or on the other band in DBS case. P2P supported channel list is |
| * modified, to only include AP interface's operating-channel and the |
| * channels of the other band if DBS is supported. |
| * |
| * These restrictions are only applicable as long as the AP/GO interface |
| * is alive. If the AP/GO interface is brought down then this |
| * setting/restriction is forgotten. |
| * |
| * If this variable is set on an AP/GO interface while a multi-channel |
| * concurrent session is active, it has no effect on the operation of |
| * the current interfaces, other than restricting the scan to the AP/GO |
| * operating channel and the other band channels if DBS is supported. |
| * However, if the STA is brought down and restarted then the new STA |
| * connection will either be formed on the AP/GO channel or on the |
| * other band in a DBS case. This is because of the scan being |
| * restricted on these channels as mentioned above. |
| * |
| * 1-Restrict / 0-Don't restrict offchannel operations. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_RESTRICT_OFFCHANNEL = 49, |
| /* |
| * 8 bit unsigned value to enable/disable LRO (Large Receive Offload) |
| * on an interface. |
| * 1 - Enable, 0 - Disable. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_LRO = 50, |
| |
| /* |
| * 8 bit unsigned value to globally enable/disable scan |
| * 1 - Enable, 0 - Disable. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_SCAN_ENABLE = 51, |
| |
| /* 8-bit unsigned value to set the total beacon miss count |
| * This parameter will set the total beacon miss count. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_TOTAL_BEACON_MISS_COUNT = 52, |
| |
| /* Unsigned 32-bit value to configure the number of continuous |
| * Beacon Miss which shall be used by the firmware to penalize |
| * the RSSI for BTC. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_PENALIZE_AFTER_NCONS_BEACON_MISS_BTC = 53, |
| |
| /* 8-bit unsigned value to configure the driver and below layers to |
| * enable/disable all FILS features. |
| * 0-enable, 1-disable |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_DISABLE_FILS = 54, |
| |
| /* 16-bit unsigned value to configure the level of WLAN latency |
| * module. See enum qca_wlan_vendor_attr_config_latency_level. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL = 55, |
| |
| /* 8-bit unsigned value indicating the driver to use the RSNE as-is from |
| * the connect interface. Exclusively used for the scenarios where the |
| * device is used as a test bed device with special functionality and |
| * not recommended for production. This helps driver to not validate the |
| * RSNE passed from user space and thus allow arbitrary IE data to be |
| * used for testing purposes. |
| * 1-enable, 0-disable. |
| * Applications set/reset this configuration. If not reset, this |
| * parameter remains in use until the driver is unloaded. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_RSN_IE = 56, |
| |
| /* 8-bit unsigned value to trigger green Tx power saving. |
| * 1-Enable, 0-Disable |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_GTX = 57, |
| |
| /* Attribute to configure disconnect IEs to the driver. |
| * This carries an array of unsigned 8-bit characters. |
| * |
| * If this is configured, driver shall fill the IEs in disassoc/deauth |
| * frame. |
| * These IEs are expected to be considered only for the next |
| * immediate disconnection (disassoc/deauth frame) originated by |
| * the DUT, irrespective of the entity (user space/driver/firmware) |
| * triggering the disconnection. |
| * The host drivers are not expected to use the IEs set through |
| * this interface for further disconnections after the first immediate |
| * disconnection initiated post the configuration. |
| * If the IEs are also updated through cfg80211 interface (after the |
| * enhancement to cfg80211_disconnect), host driver is expected to |
| * take the union of IEs from both of these interfaces and send in |
| * further disassoc/deauth frames. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_DISCONNECT_IES = 58, |
| |
| /* 8-bit unsigned value for ELNA bypass. |
| * 0 - Disable eLNA bypass. |
| * 1 - Enable eLNA bypass. |
| * 2 - Reset eLNA bypass configuration, the driver should |
| * revert to the default configuration of eLNA bypass. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_ELNA_BYPASS = 59, |
| |
| /* 8-bit unsigned value. This attribute enables/disables the host driver |
| * to send the Beacon Report Response with failure reason for the |
| * scenarios where STA cannot honor the Beacon Report Request from AP. |
| * 1-Enable, 0-Disable. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_BEACON_REPORT_FAIL = 60, |
| |
| /* 8-bit unsigned value. This attribute enables/disables the host driver |
| * to send roam reason information in the Reassociation Request frame to |
| * the target AP when roaming within the same ESS. |
| * 1-Enable, 0-Disable. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_ROAM_REASON = 61, |
| |
| /* 32-bit unsigned value to configure different PHY modes to the |
| * driver/firmware. The possible values are defined in |
| * enum qca_wlan_vendor_phy_mode. The configuration will be reset to |
| * default value, i.e., QCA_WLAN_VENDOR_PHY_MODE_AUTO upon restarting |
| * the driver. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_PHY_MODE = 62, |
| |
| /* 8-bit unsigned value to configure the maximum supported channel width |
| * for STA mode. If this value is configured when STA is in connected |
| * state, it should not exceed the negotiated channel width. If it is |
| * configured when STA is in disconnected state, the configured value |
| * will take effect for the next immediate connection. |
| * |
| * This uses values defined in enum nl80211_chan_width. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_CHANNEL_WIDTH = 63, |
| |
| /* 8-bit unsigned value to enable/disable dynamic bandwidth adjustment. |
| * This attribute is only applicable for STA mode. When dynamic |
| * bandwidth adjustment is disabled, STA will use static channel width |
| * the value of which is negotiated during connection. |
| * 1-enable (default), 0-disable |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_DYNAMIC_BW = 64, |
| |
| /* 8-bit unsigned value to configure the maximum number of subframes of |
| * TX MSDU for aggregation. Possible values are 0-31. When set to 0, |
| * it is decided by the hardware. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_TX_MSDU_AGGREGATION = 65, |
| |
| /* 8-bit unsigned value to configure the maximum number of subframes of |
| * RX MSDU for aggregation. Possible values are 0-31. When set to 0, |
| * it is decided by the hardware. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_RX_MSDU_AGGREGATION = 66, |
| |
| /* 8-bit unsigned value. This attribute is used to dynamically |
| * enable/disable the LDPC capability of the device. When configured in |
| * the disconnected state, the updated configuration will be considered |
| * for the immediately following connection attempt. If this |
| * configuration is modified while the device is in the connected state, |
| * the LDPC TX will be updated with this configuration immediately, |
| * while the LDPC RX configuration update will take place starting from |
| * the subsequent association attempt. |
| * 1-Enable, 0-Disable. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_LDPC = 67, |
| |
| /* 8-bit unsigned value. This attribute is used to dynamically |
| * enable/disable the TX STBC capability of the device. When configured |
| * in the disconnected state, the updated configuration will be |
| * considered for the immediately following connection attempt. If the |
| * connection is formed with TX STBC enabled and if this configuration |
| * is disabled during that association, the TX will be impacted |
| * immediately. Further connection attempts will disable TX STBC. |
| * However, enabling the TX STBC for a connected session with disabled |
| * capability is not allowed and will fail. |
| * 1-Enable, 0-Disable. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_TX_STBC = 68, |
| |
| /* 8-bit unsigned value. This attribute is used to dynamically |
| * enable/disable the RX STBC capability of the device. When configured |
| * in the disconnected state, the updated configuration will be |
| * considered for the immediately following connection attempt. If the |
| * configuration is modified in the connected state, there will be no |
| * impact for the current association, but further connection attempts |
| * will use the updated configuration. |
| * 1-Enable, 0-Disable. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_RX_STBC = 69, |
| |
| /* 8-bit unsigned value. This attribute is used to dynamically configure |
| * the number of spatial streams. When configured in the disconnected |
| * state, the updated configuration will be considered for the |
| * immediately following connection attempt. If the NSS is updated after |
| * the connection, the updated NSS value is notified to the peer using |
| * the Operating Mode Notification/Spatial Multiplexing Power Save |
| * frame. The updated NSS value after the connection shall not be |
| * greater than the one negotiated during the connection. Any such |
| * higher value configuration shall be returned with a failure. |
| * Only symmetric NSS configuration (such as 2X2 or 1X1) can be done |
| * using this attribute. QCA_WLAN_VENDOR_ATTR_CONFIG_TX_NSS and |
| * QCA_WLAN_VENDOR_ATTR_CONFIG_RX_NSS attributes shall be used to |
| * configure the asymmetric NSS configuration (such as 1X2). |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_NSS = 70, |
| /* 8-bit unsigned value to trigger Optimized Power Management: |
| * 1-Enable, 0-Disable |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_OPTIMIZED_POWER_MANAGEMENT = 71, |
| |
| /* 8-bit unsigned value. This attribute takes the QoS/access category |
| * value represented by the enum qca_wlan_ac_type and expects the driver |
| * to upgrade the UDP frames to this access category. The value of |
| * QCA_WLAN_AC_ALL is invalid for this attribute. This will override the |
| * DSCP value configured in the frame with the intention to only upgrade |
| * the access category. That said, it is not intended to downgrade the |
| * access category for the frames. |
| * Set the value to QCA_WLAN_AC_BK if the QoS upgrade needs to be |
| * disabled, as BK is of the lowest priority and an upgrade to it does |
| * not result in any changes for the frames. |
| * |
| * If only UDP frames of BE or BK access category needs to be upgraded |
| * without changing the access category of VO or VI UDP frames, refer to |
| * attribute QCA_WLAN_VENDOR_ATTR_CONFIG_UDP_QOS_UPGRADE_FOR_BE_BK. |
| * |
| * This attribute is not recommended to be used as it blindly forces all |
| * UDP packets to a higher access category which could impact the |
| * traffic pattern of all apps using UDP and can cause unknown behavior. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_UDP_QOS_UPGRADE = 72, |
| |
| /* 8-bit unsigned value. This attribute is used to dynamically configure |
| * the number of chains to be used for transmitting data. This |
| * configuration is allowed only when in connected state and will be |
| * effective until disconnected. The driver rejects this configuration |
| * if the number of spatial streams being used in the current connection |
| * cannot be supported by this configuration. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_NUM_TX_CHAINS = 73, |
| /* 8-bit unsigned value. This attribute is used to dynamically configure |
| * the number of chains to be used for receiving data. This |
| * configuration is allowed only when in connected state and will be |
| * effective until disconnected. The driver rejects this configuration |
| * if the number of spatial streams being used in the current connection |
| * cannot be supported by this configuration. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_NUM_RX_CHAINS = 74, |
| |
| /* 8-bit unsigned value to configure ANI setting type. |
| * See &enum qca_wlan_ani_setting for possible values. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_ANI_SETTING = 75, |
| /* 32-bit signed value to configure ANI level. This is used when |
| * ANI settings type is &QCA_WLAN_ANI_SETTING_FIXED. |
| * The set and get of ANI level with &QCA_WLAN_ANI_SETTING_AUTO |
| * is invalid, the driver will return a failure. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_ANI_LEVEL = 76, |
| |
| /* 8-bit unsigned value. This attribute is used to dynamically configure |
| * the number of spatial streams used for transmitting the data. When |
| * configured in the disconnected state, the configured value will |
| * be considered for the following connection attempt. |
| * If the NSS is updated after the connection, the updated NSS value |
| * is notified to the peer using the Operating Mode Notification/Spatial |
| * Multiplexing Power Save frame. |
| * The TX NSS value configured after the connection shall not be greater |
| * than the value negotiated during the connection. Any such higher |
| * value configuration shall be treated as invalid configuration by |
| * the driver. This attribute shall be configured along with |
| * QCA_WLAN_VENDOR_ATTR_CONFIG_RX_NSS attribute to define the symmetric |
| * configuration (such as 2X2 or 1X1) or the asymmetric |
| * configuration (such as 1X2). |
| * If QCA_WLAN_VENDOR_ATTR_CONFIG_NSS attribute is also provided along |
| * with this QCA_WLAN_VENDOR_ATTR_CONFIG_TX_NSS attribute the driver |
| * will update the TX NSS based on QCA_WLAN_VENDOR_ATTR_CONFIG_TX_NSS. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_TX_NSS = 77, |
| |
| /* 8-bit unsigned value. This attribute is used to dynamically configure |
| * the number of spatial streams used for receiving the data. When |
| * configured in the disconnected state, the configured value will |
| * be considered for the following connection attempt. |
| * If the NSS is updated after the connection, the updated NSS value |
| * is notified to the peer using the Operating Mode Notification/Spatial |
| * Multiplexing Power Save frame. |
| * The RX NSS value configured after the connection shall not be greater |
| * than the value negotiated during the connection. Any such higher |
| * value configuration shall be treated as invalid configuration by |
| * the driver. This attribute shall be configured along with |
| * QCA_WLAN_VENDOR_ATTR_CONFIG_TX_NSS attribute to define the symmetric |
| * configuration (such as 2X2 or 1X1) or the asymmetric |
| * configuration (such as 1X2). |
| * If QCA_WLAN_VENDOR_ATTR_CONFIG_NSS attribute is also provided along |
| * with this QCA_WLAN_VENDOR_ATTR_CONFIG_RX_NSS attribute the driver |
| * will update the RX NSS based on QCA_WLAN_VENDOR_ATTR_CONFIG_RX_NSS. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_RX_NSS = 78, |
| |
| /* |
| * 8-bit unsigned value. This attribute, when set, indicates whether the |
| * specified interface is the primary STA interface when there are more |
| * than one STA interfaces concurrently active. |
| * |
| * This configuration helps the firmware/hardware to support certain |
| * features (e.g., roaming) on this primary interface, if the same |
| * cannot be supported on the concurrent STA interfaces simultaneously. |
| * |
| * This configuration is only applicable for a single STA interface on |
| * a device and gives the priority for it only over other concurrent STA |
| * interfaces. |
| * |
| * If the device is a multi wiphy/soc, this configuration applies to a |
| * single STA interface across the wiphys. |
| * |
| * 1-Enable (is the primary STA), 0-Disable (is not the primary STA) |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_CONCURRENT_STA_PRIMARY = 79, |
| |
| /* |
| * 8-bit unsigned value. This attribute can be used to configure the |
| * driver to enable/disable FT-over-DS feature. Possible values for |
| * this attribute are 1-Enable and 0-Disable. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_FT_OVER_DS = 80, |
| |
| /* |
| * 8-bit unsigned value. This attribute can be used to configure the |
| * firmware to enable/disable ARP/NS offload feature. Possible values |
| * for this attribute are 0-Disable and 1-Enable. |
| * |
| * This attribute is only applicable for STA/P2P-Client interface, |
| * and is optional, default behavior is ARP/NS offload enabled. |
| * |
| * This attribute can be set in disconnected and connected state, and |
| * will restore to the default behavior if the interface is closed. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_ARP_NS_OFFLOAD = 81, |
| |
| /* |
| * 8-bit unsigned value. This attribute can be used to configure the |
| * data path mode to be followed for audio traffic. Possible values |
| * are defined in enum qca_wlan_audio_data_path. |
| * |
| * This attribute is used only when the driver advertises support for |
| * QCA_WLAN_VENDOR_FEATURE_ENHANCED_AUDIO_EXPERIENCE_OVER_WLAN. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_AUDIO_DATA_PATH = 82, |
| |
| /* |
| * 8-bit unsigned value. This attribute can be used to configure the |
| * Dedicated Bluetooth Antenna Mode (DBAM) feature. Possible values for |
| * this attribute are defined in the enum qca_wlan_dbam_config. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_DBAM = 83, |
| |
| /* 8-bit unsigned value. This attribute takes the QoS/access category |
| * value represented by the enum qca_wlan_ac_type and expects the driver |
| * to upgrade the UDP frames of BE or BK access category to this access |
| * category. This attribute will not modify UDP frames of VO or VI |
| * access category. The value of QCA_WLAN_AC_ALL is invalid for this |
| * attribute. |
| * |
| * This will override the DSCP value configured in the frame with the |
| * intention to only upgrade the access category. That said, it is not |
| * intended to downgrade the access category for the frames. |
| * Set the value to QCA_WLAN_AC_BK if the QoS upgrade needs to be |
| * disabled, as BK is of the lowest priority and an upgrade to it does |
| * not result in any changes for the frames. |
| * |
| * This attribute behavior is similar to |
| * QCA_WLAN_VENDOR_ATTR_CONFIG_UDP_QOS_UPGRADE with the difference that |
| * only UDP frames of BE or BK access category are upgraded and not |
| * UDP frames of VI or VO access category. |
| * |
| * This attribute is not recommended to be used as it blindly forces all |
| * UDP packets of BE or BK access category to a higher access category |
| * which could impact the traffic pattern of all apps using UDP and can |
| * cause unknown behavior. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_UDP_QOS_UPGRADE_FOR_BE_BK = 84, |
| |
| /* 8-bit unsigned value to configure the driver to enable/disable the |
| * periodic sounding for Tx beamformer functionality. The default |
| * behavior uses algorithm to do sounding based on packet stats. |
| * |
| * 0 - Default behavior. |
| * 1 - Enable the periodic sounding for Tx beamformer. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_BEAMFORMER_PERIODIC_SOUNDING = 85, |
| |
| /* 8-bit unsigned value, whenever wifi calling (wfc) begins or ends, |
| * userspace sends this information to the driver/firmware to configure |
| * wfc state. The driver/firmware uses this information to |
| * optimize power savings, rate adaption, roaming, etc. |
| * |
| * 1 - wfc is on. |
| * 0 - wfc is off. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_WFC_STATE = 86, |
| |
| /* 8-bit unsigned value to configure the driver to enable/disable the |
| * EHT EML capability in management frame EHT capabilities. |
| * 1 - Enable, 0 - Disable. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_EHT_EML_CAPABILITY = 87, |
| |
| /* 8-bit unsigned value to configure the driver with EHT MLO max |
| * simultaneous links to be used for MLO connection. |
| * The range of the value is 0 to 14. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_EHT_MLO_MAX_SIMULTANEOUS_LINKS = 88, |
| |
| /* 8-bit unsigned value to configure the driver with EHT MLO maximum |
| * number of links to be used for MLO connection. |
| * The range of the value is 1 to 16. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_EHT_MLO_MAX_NUM_LINKS = 89, |
| |
| /* 8-bit unsigned value to configure the driver with EHT MLO mode. |
| * Uses enum qca_wlan_eht_mlo_mode values. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_EHT_MLO_MODE = 90, |
| |
| /* Nested attribute with frequencies in u32 attributes to configure a |
| * list of allowed 20 MHz channel center frequencies in MHz for AP |
| * operation. Whenever performing a channel selection operation, the |
| * driver shall generate a new list based on this provided list by |
| * filtering out channels that cannot be used at that time due to |
| * regulatory or other constraints. The resulting list is used as the |
| * list of all allowed channels, i.e., operation on any channel that is |
| * not included is not allowed, whenever performing operations like ACS |
| * and DFS. |
| * |
| * Userspace shall configure this before starting the AP and the |
| * configuration is valid only from the next BSS start and until the |
| * BSS is stopped. The driver shall clear this configuration when the |
| * AP is stopped and fall back to the default behavior for subsequent |
| * AP operation. |
| * |
| * The default behavior when this configuration is not applicable is the |
| * driver can choose any of the channels supported by the hardware |
| * except the channels that cannot be used due to regulatory or other |
| * constraints. |
| * |
| * The driver shall reject this configuration if done after the AP is |
| * started. This attribute can be used to specify user's choice of |
| * frequencies and static puncture channel list, etc. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_AP_ALLOWED_FREQ_LIST = 91, |
| |
| /* Nested attribute to indicate EHT MLO links to be forced active. |
| * It contains link MAC address attributes. These nested attributes are |
| * of the type NL80211_ATTR_MAC and are used to force enabling of the |
| * MLO links corresponding to the indicated link MAC addresses. |
| * Subsequently, the links corresponding to the link MAC addresses that |
| * are not indicated are forced inactive. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_EHT_MLO_ACTIVE_LINKS = 92, |
| |
| /* 8-bit unsigned value to configure EMLSR mode entry or exit. |
| * Uses enum qca_wlan_emlsr_mode values. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_EMLSR_MODE_SWITCH = 93, |
| |
| /* 8-bit unsigned value to configure the channel bandwidth |
| * for CTS frame transmission during the dymamic bandwidth |
| * signaling CTS procedure referred in IEEE Std 802.11-2020, |
| * 10.3.2.9 CTS and DMG CTS procedure. |
| * This configuration is used for testing purposes. |
| * |
| * This uses values defined in enum nl80211_chan_width. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_CTS_CHANNEL_WIDTH = 94, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_CONFIG_MAX = |
| QCA_WLAN_VENDOR_ATTR_CONFIG_AFTER_LAST - 1, |
| }; |
| |
| /* Compatibility defines for previously used incorrect enum |
| * qca_wlan_vendor_attr_config names. These values should not be used in any |
| * new implementation. */ |
| #define QCA_WLAN_VENDOR_ATTR_DISCONNECT_IES \ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_DISCONNECT_IES |
| #define QCA_WLAN_VENDOR_ATTR_BEACON_REPORT_FAIL \ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_BEACON_REPORT_FAIL |
| |
| /** |
| * enum qca_dbam_config - Specifies DBAM config mode |
| * @QCA_DBAM_DISABLE: Firmware disables DBAM |
| * @QCA_DBAM_ENABLE: Firmware enables DBAM opportunistically when |
| * internal criteria are met. |
| * @QCA_DBAM_FORCE_ENABLE: Firmware enables DBAM forcefully. |
| */ |
| enum qca_dbam_config { |
| QCA_DBAM_DISABLE = 0, |
| QCA_DBAM_ENABLE = 1, |
| QCA_DBAM_FORCE_ENABLE = 2, |
| }; |
| |
| /** |
| * enum qca_wlan_ani_setting - ANI setting type |
| * @QCA_WLAN_ANI_SETTING_AUTO: Automatically determine ANI level |
| * @QCA_WLAN_ANI_SETTING_FIXED: Fix ANI level to the dBm parameter |
| */ |
| enum qca_wlan_ani_setting { |
| QCA_WLAN_ANI_SETTING_AUTO = 0, |
| QCA_WLAN_ANI_SETTING_FIXED = 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_sap_config - Parameters for AP configuration |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_CHANNEL: Optional (u8) |
| * Channel number on which Access Point should restart. |
| * Note: If both the driver and user space application supports the 6 GHz band, |
| * this attribute is deprecated and QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_FREQUENCY |
| * should be used. |
| * To maintain backward compatibility, QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_CHANNEL |
| * is still used if either of the driver or user space application doesn't |
| * support the 6 GHz band. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_FREQUENCY: Optional (u32) |
| * Channel center frequency (MHz) on which the access point should restart. |
| */ |
| enum qca_wlan_vendor_attr_sap_config { |
| QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_CHANNEL = 1, |
| |
| /* List of frequencies on which AP is expected to operate. |
| * This is irrespective of ACS configuration. This list is a priority |
| * based one and is looked for before the AP is created to ensure the |
| * best concurrency sessions (avoid MCC and use DBS/SCC) co-exist in |
| * the system. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SAP_MANDATORY_FREQUENCY_LIST = 2, |
| QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_FREQUENCY = 3, |
| |
| QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_MAX = |
| QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_sap_conditional_chan_switch - Parameters for AP |
| * conditional channel switch |
| */ |
| enum qca_wlan_vendor_attr_sap_conditional_chan_switch { |
| QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_INVALID = 0, |
| /* Priority based frequency list (an array of u32 values in host byte |
| * order) |
| */ |
| QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_FREQ_LIST = 1, |
| /* Status of the conditional switch (u32). |
| * 0: Success, Non-zero: Failure |
| */ |
| QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_STATUS = 2, |
| |
| QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_MAX = |
| QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_gpio_attr - Parameters for GPIO configuration |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND: Required (u32) |
| * value to specify the GPIO command. Please refer to enum qca_gpio_cmd_type |
| * for the available values. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_PINNUM: Required (u32) |
| * value to specify the GPIO number. |
| * This is required, when %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND is |
| * %QCA_WLAN_VENDOR_GPIO_CONFIG or %QCA_WLAN_VENDOR_GPIO_OUTPUT. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_VALUE: Required (u32) |
| * value to specify the GPIO output level. Please refer to enum qca_gpio_value |
| * for the available values. |
| * This is required, when %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND is |
| * %QCA_WLAN_VENDOR_GPIO_OUTPUT. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_PULL_TYPE: Optional (u32) |
| * value to specify the GPIO pull type. Please refer to enum qca_gpio_pull_type |
| * for the available values. |
| * This is required, when %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND is |
| * %QCA_WLAN_VENDOR_GPIO_CONFIG and |
| * %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTERNAL_CONFIG attribute is not present. |
| * Optional when %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTERNAL_CONFIG |
| * attribute is present. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTR_MODE: Optional (u32) |
| * value to specify the GPIO interrupt mode. Please refer to enum |
| * qca_gpio_interrupt_mode for the available values. |
| * This is required, when %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND is |
| * %QCA_WLAN_VENDOR_GPIO_CONFIG and |
| * %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTERNAL_CONFIG attribute is not present. |
| * Optional when %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTERNAL_CONFIG |
| * attribute is present. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_DIR: Optional (u32) |
| * value to specify the GPIO direction. Please refer to enum qca_gpio_direction |
| * for the available values. |
| * This is required, when %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND is |
| * %QCA_WLAN_VENDOR_GPIO_CONFIG and |
| * %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTERNAL_CONFIG attribute is not present. |
| * Optional when %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTERNAL_CONFIG |
| * attribute is present. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_MUX_CONFIG: Optional (u32) |
| * Value to specify the mux config. Meaning of a given value is dependent |
| * on the target chipset and GPIO pin. Must be of the range 0-15. |
| * Optional when %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND is |
| * %QCA_WLAN_VENDOR_GPIO_CONFIG. Defaults to 0. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_DRIVE: Optional (u32) |
| * Value to specify the drive, refer to enum qca_gpio_drive. |
| * Optional when %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND is |
| * %QCA_WLAN_VENDOR_GPIO_CONFIG. Defaults to QCA_WLAN_GPIO_DRIVE_2MA(0). |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTERNAL_CONFIG: Optional (flag) |
| * Optional when %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND is |
| * %QCA_WLAN_VENDOR_GPIO_CONFIG. When present this attribute signals that all |
| * other parameters for the given GPIO will be obtained from internal |
| * configuration. Only %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_PINNUM must be |
| * specified to indicate the GPIO pin being configured. |
| */ |
| enum qca_wlan_gpio_attr { |
| QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INVALID = 0, |
| /* Unsigned 32-bit attribute for GPIO command */ |
| QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND = 1, |
| /* Unsigned 32-bit attribute for GPIO PIN number to configure */ |
| QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_PINNUM = 2, |
| /* Unsigned 32-bit attribute for GPIO value to configure */ |
| QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_VALUE = 3, |
| /* Unsigned 32-bit attribute for GPIO pull type */ |
| QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_PULL_TYPE = 4, |
| /* Unsigned 32-bit attribute for GPIO interrupt mode */ |
| QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTR_MODE = 5, |
| /* Unsigned 32-bit attribute for GPIO direction to configure */ |
| QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_DIR = 6, |
| /* Unsigned 32-bit attribute for GPIO mux config */ |
| QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_MUX_CONFIG = 7, |
| /* Unsigned 32-bit attribute for GPIO drive */ |
| QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_DRIVE = 8, |
| /* Flag attribute for using internal GPIO configuration */ |
| QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTERNAL_CONFIG = 9, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_LAST, |
| QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_MAX = |
| QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_LAST - 1 |
| }; |
| |
| /** |
| * enum gpio_cmd_type - GPIO configuration command type |
| * @QCA_WLAN_VENDOR_GPIO_CONFIG: Set GPIO configuration info |
| * @QCA_WLAN_VENDOR_GPIO_OUTPUT: Set GPIO output level |
| */ |
| enum qca_gpio_cmd_type { |
| QCA_WLAN_VENDOR_GPIO_CONFIG = 0, |
| QCA_WLAN_VENDOR_GPIO_OUTPUT = 1, |
| }; |
| |
| /** |
| * enum qca_gpio_pull_type - GPIO pull type |
| * @QCA_WLAN_GPIO_PULL_NONE: Set GPIO pull type to none |
| * @QCA_WLAN_GPIO_PULL_UP: Set GPIO pull up |
| * @QCA_WLAN_GPIO_PULL_DOWN: Set GPIO pull down |
| */ |
| enum qca_gpio_pull_type { |
| QCA_WLAN_GPIO_PULL_NONE = 0, |
| QCA_WLAN_GPIO_PULL_UP = 1, |
| QCA_WLAN_GPIO_PULL_DOWN = 2, |
| QCA_WLAN_GPIO_PULL_MAX, |
| }; |
| |
| /** |
| * enum qca_gpio_direction - GPIO direction |
| * @QCA_WLAN_GPIO_INPUT: Set GPIO as input mode |
| * @QCA_WLAN_GPIO_OUTPUT: Set GPIO as output mode |
| * @QCA_WLAN_GPIO_VALUE_MAX: Invalid value |
| */ |
| enum qca_gpio_direction { |
| QCA_WLAN_GPIO_INPUT = 0, |
| QCA_WLAN_GPIO_OUTPUT = 1, |
| QCA_WLAN_GPIO_DIR_MAX, |
| }; |
| |
| /** |
| * enum qca_gpio_value - GPIO Value |
| * @QCA_WLAN_GPIO_LEVEL_LOW: set gpio output level to low |
| * @QCA_WLAN_GPIO_LEVEL_HIGH: set gpio output level to high |
| * @QCA_WLAN_GPIO_LEVEL_MAX: Invalid value |
| */ |
| enum qca_gpio_value { |
| QCA_WLAN_GPIO_LEVEL_LOW = 0, |
| QCA_WLAN_GPIO_LEVEL_HIGH = 1, |
| QCA_WLAN_GPIO_LEVEL_MAX, |
| }; |
| |
| /** |
| * enum gpio_interrupt_mode - GPIO interrupt mode |
| * @QCA_WLAN_GPIO_INTMODE_DISABLE: Disable interrupt trigger |
| * @QCA_WLAN_GPIO_INTMODE_RISING_EDGE: Interrupt with GPIO rising edge trigger |
| * @QCA_WLAN_GPIO_INTMODE_FALLING_EDGE: Interrupt with GPIO falling edge trigger |
| * @QCA_WLAN_GPIO_INTMODE_BOTH_EDGE: Interrupt with GPIO both edge trigger |
| * @QCA_WLAN_GPIO_INTMODE_LEVEL_LOW: Interrupt with GPIO level low trigger |
| * @QCA_WLAN_GPIO_INTMODE_LEVEL_HIGH: Interrupt with GPIO level high trigger |
| * @QCA_WLAN_GPIO_INTMODE_MAX: Invalid value |
| */ |
| enum qca_gpio_interrupt_mode { |
| QCA_WLAN_GPIO_INTMODE_DISABLE = 0, |
| QCA_WLAN_GPIO_INTMODE_RISING_EDGE = 1, |
| QCA_WLAN_GPIO_INTMODE_FALLING_EDGE = 2, |
| QCA_WLAN_GPIO_INTMODE_BOTH_EDGE = 3, |
| QCA_WLAN_GPIO_INTMODE_LEVEL_LOW = 4, |
| QCA_WLAN_GPIO_INTMODE_LEVEL_HIGH = 5, |
| QCA_WLAN_GPIO_INTMODE_MAX, |
| }; |
| |
| /** |
| * enum qca_gpio_drive - GPIO drive |
| * @QCA_WLAN_GPIO_DRIVE_2MA: drive 2MA |
| * @QCA_WLAN_GPIO_DRIVE_4MA: drive 4MA |
| * @QCA_WLAN_GPIO_DRIVE_6MA: drive 6MA |
| * @QCA_WLAN_GPIO_DRIVE_8MA: drive 8MA |
| * @QCA_WLAN_GPIO_DRIVE_10MA: drive 10MA |
| * @QCA_WLAN_GPIO_DRIVE_12MA: drive 12MA |
| * @QCA_WLAN_GPIO_DRIVE_14MA: drive 14MA |
| * @QCA_WLAN_GPIO_DRIVE_16MA: drive 16MA |
| * @QCA_WLAN_GPIO_DRIVE_MAX: invalid GPIO drive |
| */ |
| enum qca_gpio_drive { |
| QCA_WLAN_GPIO_DRIVE_2MA = 0, |
| QCA_WLAN_GPIO_DRIVE_4MA = 1, |
| QCA_WLAN_GPIO_DRIVE_6MA = 2, |
| QCA_WLAN_GPIO_DRIVE_8MA = 3, |
| QCA_WLAN_GPIO_DRIVE_10MA = 4, |
| QCA_WLAN_GPIO_DRIVE_12MA = 5, |
| QCA_WLAN_GPIO_DRIVE_14MA = 6, |
| QCA_WLAN_GPIO_DRIVE_16MA = 7, |
| QCA_WLAN_GPIO_DRIVE_MAX, |
| }; |
| |
| /** |
| * qca_wlan_set_qdepth_thresh_attr - Parameters for setting |
| * MSDUQ depth threshold per peer per tid in the target |
| * |
| * Associated Vendor Command: |
| * QCA_NL80211_VENDOR_SUBCMD_SET_QDEPTH_THRESH |
| */ |
| enum qca_wlan_set_qdepth_thresh_attr { |
| QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_INVALID = 0, |
| /* 6-byte MAC address */ |
| QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_MAC_ADDR, |
| /* Unsigned 32-bit attribute for holding the TID */ |
| QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_TID, |
| /* Unsigned 32-bit attribute for holding the update mask |
| * bit 0 - Update high priority msdu qdepth threshold |
| * bit 1 - Update low priority msdu qdepth threshold |
| * bit 2 - Update UDP msdu qdepth threshold |
| * bit 3 - Update Non UDP msdu qdepth threshold |
| * rest of bits are reserved |
| */ |
| QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_UPDATE_MASK, |
| /* Unsigned 32-bit attribute for holding the threshold value */ |
| QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_VALUE, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_LAST, |
| QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_MAX = |
| QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_acs_dfs_mode - Defines different types of DFS channel |
| * configurations for ACS operation. |
| * |
| * @QCA_ACS_DFS_MODE_NONE: Refer to invalid DFS mode |
| * @QCA_ACS_DFS_MODE_ENABLE: Consider DFS channels in ACS operation |
| * @QCA_ACS_DFS_MODE_DISABLE: Do not consider DFS channels in ACS operation |
| * @QCA_ACS_DFS_MODE_DEPRIORITIZE: Deprioritize DFS channels in ACS operation |
| */ |
| enum qca_acs_dfs_mode { |
| QCA_ACS_DFS_MODE_NONE = 0, |
| QCA_ACS_DFS_MODE_ENABLE = 1, |
| QCA_ACS_DFS_MODE_DISABLE = 2, |
| QCA_ACS_DFS_MODE_DEPRIORITIZE = 3, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_acs_config - Defines Configuration attributes |
| * used by the vendor command QCA_NL80211_VENDOR_SUBCMD_ACS_POLICY. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ACS_DFS_MODE: Required (u8) |
| * DFS mode for ACS operation from enum qca_acs_dfs_mode. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ACS_CHANNEL_HINT: Required (u8) |
| * channel number hint for ACS operation, if valid channel is specified then |
| * ACS operation gives priority to this channel. |
| * Note: If both the driver and user space application supports the 6 GHz band, |
| * this attribute is deprecated and QCA_WLAN_VENDOR_ATTR_ACS_FREQUENCY_HINT |
| * should be used. |
| * To maintain backward compatibility, QCA_WLAN_VENDOR_ATTR_ACS_CHANNEL_HINT |
| * is still used if either of the driver or user space application doesn't |
| * support the 6 GHz band. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ACS_FREQUENCY_HINT: Required (u32). |
| * Channel center frequency (MHz) hint for ACS operation, if a valid center |
| * frequency is specified, ACS operation gives priority to this channel. |
| */ |
| enum qca_wlan_vendor_attr_acs_config { |
| QCA_WLAN_VENDOR_ATTR_ACS_MODE_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_ACS_DFS_MODE = 1, |
| QCA_WLAN_VENDOR_ATTR_ACS_CHANNEL_HINT = 2, |
| QCA_WLAN_VENDOR_ATTR_ACS_FREQUENCY_HINT = 3, |
| |
| QCA_WLAN_VENDOR_ATTR_ACS_DFS_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_ACS_DFS_MAX = |
| QCA_WLAN_VENDOR_ATTR_ACS_DFS_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_get_hw_capability - Wi-Fi hardware capability |
| */ |
| enum qca_wlan_vendor_attr_get_hw_capability { |
| QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_INVALID, |
| /* Antenna isolation |
| * An attribute used in the response. |
| * The content of this attribute is encoded in a byte array. Each byte |
| * value is an antenna isolation value. The array length is the number |
| * of antennas. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ANTENNA_ISOLATION, |
| /* Request HW capability |
| * An attribute used in the request. |
| * The content of this attribute is a u32 array for one or more of |
| * hardware capabilities (attribute IDs) that are being requested. Each |
| * u32 value has a value from this |
| * enum qca_wlan_vendor_attr_get_hw_capability |
| * identifying which capabilities are requested. |
| */ |
| QCA_WLAN_VENDOR_ATTR_GET_HW_CAPABILITY, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_MAX = |
| QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_ll_stats_ext - Attributes for MAC layer monitoring |
| * offload which is an extension for LL_STATS. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_PERIOD: Monitoring period. Unit in ms. |
| * If MAC counters do not exceed the threshold, FW will report monitored |
| * link layer counters periodically as this setting. The first report is |
| * always triggered by this timer. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_THRESHOLD: It is a percentage (1-99). |
| * For each MAC layer counter, FW holds two copies. One is the current value. |
| * The other is the last report. Once a current counter's increment is larger |
| * than the threshold, FW will indicate that counter to host even if the |
| * monitoring timer does not expire. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_CHG: Peer STA power state change |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TID: TID of MSDU |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NUM_MSDU: Count of MSDU with the same |
| * failure code. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_STATUS: TX failure code |
| * 1: TX packet discarded |
| * 2: No ACK |
| * 3: Postpone |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_MAC_ADDRESS: peer MAC address |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_STATE: Peer STA current state |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_GLOBAL: Global threshold. |
| * Threshold for all monitored parameters. If per counter dedicated threshold |
| * is not enabled, this threshold will take effect. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_EVENT_MODE: Indicate what triggers this |
| * event, PERORID_TIMEOUT == 1, THRESH_EXCEED == 0. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_ID: interface ID |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ID: peer ID |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BITMAP: bitmap for TX counters |
| * Bit0: TX counter unit in MSDU |
| * Bit1: TX counter unit in MPDU |
| * Bit2: TX counter unit in PPDU |
| * Bit3: TX counter unit in byte |
| * Bit4: Dropped MSDUs |
| * Bit5: Dropped Bytes |
| * Bit6: MPDU retry counter |
| * Bit7: MPDU failure counter |
| * Bit8: PPDU failure counter |
| * Bit9: MPDU aggregation counter |
| * Bit10: MCS counter for ACKed MPDUs |
| * Bit11: MCS counter for Failed MPDUs |
| * Bit12: TX Delay counter |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BITMAP: bitmap for RX counters |
| * Bit0: MAC RX counter unit in MPDU |
| * Bit1: MAC RX counter unit in byte |
| * Bit2: PHY RX counter unit in PPDU |
| * Bit3: PHY RX counter unit in byte |
| * Bit4: Disorder counter |
| * Bit5: Retry counter |
| * Bit6: Duplication counter |
| * Bit7: Discard counter |
| * Bit8: MPDU aggregation size counter |
| * Bit9: MCS counter |
| * Bit10: Peer STA power state change (wake to sleep) counter |
| * Bit11: Peer STA power save counter, total time in PS mode |
| * Bit12: Probe request counter |
| * Bit13: Other management frames counter |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS_BITMAP: bitmap for CCA |
| * Bit0: Idle time |
| * Bit1: TX time |
| * Bit2: time RX in current bss |
| * Bit3: Out of current bss time |
| * Bit4: Wireless medium busy time |
| * Bit5: RX in bad condition time |
| * Bit6: TX in bad condition time |
| * Bit7: time wlan card not available |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_SIGNAL_BITMAP: bitmap for signal |
| * Bit0: Per channel SNR counter |
| * Bit1: Per channel noise floor counter |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_NUM: number of peers |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CHANNEL_NUM: number of channels |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_AC_RX_NUM: number of RX stats |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS: per channel BSS CCA stats |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER: container for per PEER stats |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MSDU: Number of total TX MSDUs |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MPDU: Number of total TX MPDUs |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_PPDU: Number of total TX PPDUs |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BYTES: bytes of TX data |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP: Number of dropped TX packets |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP_BYTES: Bytes dropped |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_RETRY: waiting time without an ACK |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_ACK: number of MPDU not-ACKed |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_BACK: number of PPDU not-ACKed |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR_NUM: |
| * aggregation stats buffer length |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS_NUM: length of mcs stats |
| * buffer for ACKed MPDUs. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS_NUM: length of mcs stats |
| * buffer for failed MPDUs. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_DELAY_ARRAY_SIZE: |
| * length of delay stats array. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR: TX aggregation stats |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS: MCS stats for ACKed MPDUs |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS: MCS stats for failed MPDUs |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DELAY: tx delay stats |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU: MPDUs received |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_BYTES: bytes received |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU: PPDU received |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU_BYTES: PPDU bytes received |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_LOST: packets lost |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_RETRY: number of RX packets |
| * flagged as retransmissions |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DUP: number of RX packets |
| * flagged as duplicated |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DISCARD: number of RX |
| * packets discarded |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR_NUM: length of RX aggregation |
| * stats buffer. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS_NUM: length of RX mcs |
| * stats buffer. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS: RX mcs stats buffer |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR: aggregation stats buffer |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_TIMES: times STAs go to sleep |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_DURATION: STAs' total sleep time |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PROBE_REQ: number of probe |
| * requests received |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MGMT: number of other mgmt |
| * frames received |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IDLE_TIME: Percentage of idle time |
| * there is no TX, nor RX, nor interference. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_TIME: percentage of time |
| * transmitting packets. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_TIME: percentage of time |
| * for receiving. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BUSY: percentage of time |
| * interference detected. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BAD: percentage of time |
| * receiving packets with errors. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BAD: percentage of time |
| * TX no-ACK. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NO_AVAIL: percentage of time |
| * the chip is unable to work in normal conditions. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IN_BSS_TIME: percentage of time |
| * receiving packets in current BSS. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_OUT_BSS_TIME: percentage of time |
| * receiving packets not in current BSS. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ANT_NUM: number of antennas |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_SIGNAL: |
| * This is a container for per antenna signal stats. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_SNR: per antenna SNR value |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_NF: per antenna NF value |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_RSSI_BEACON: RSSI of beacon |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_SNR_BEACON: SNR of beacon |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_REPORT_TIME: u64 |
| * Absolute timestamp from 1970/1/1, unit in ms. After receiving the |
| * message, user layer APP could call gettimeofday to get another |
| * timestamp and calculate transfer delay for the message. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_MEASUREMENT_TIME: u32 |
| * Real period for this measurement, unit in us. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PAD: Attribute used for padding for |
| * 64-bit alignment. |
| */ |
| enum qca_wlan_vendor_attr_ll_stats_ext { |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_INVALID = 0, |
| |
| /* Attributes for configurations */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_PERIOD, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_THRESHOLD, |
| |
| /* Peer STA power state change */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_CHG, |
| |
| /* TX failure event */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TID, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NUM_MSDU, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_STATUS, |
| |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_STATE, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_MAC_ADDRESS, |
| |
| /* MAC counters */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_GLOBAL, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_EVENT_MODE, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_ID, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ID, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BITMAP, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BITMAP, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS_BITMAP, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_SIGNAL_BITMAP, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_NUM, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CHANNEL_NUM, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER, |
| |
| /* Sub-attributes for PEER_AC_TX */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MSDU, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MPDU, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_PPDU, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BYTES, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP_BYTES, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_RETRY, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_ACK, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_BACK, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR_NUM, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS_NUM, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS_NUM, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_DELAY_ARRAY_SIZE, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DELAY, |
| |
| /* Sub-attributes for PEER_AC_RX */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_BYTES, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU_BYTES, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_LOST, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_RETRY, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DUP, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DISCARD, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR_NUM, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS_NUM, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_TIMES, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_DURATION, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PROBE_REQ, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MGMT, |
| |
| /* Sub-attributes for CCA_BSS */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IDLE_TIME, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_TIME, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_TIME, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BUSY, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BAD, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BAD, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NO_AVAIL, |
| |
| /* sub-attribute for BSS_RX_TIME */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IN_BSS_TIME, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_OUT_BSS_TIME, |
| |
| /* Sub-attributes for PEER_SIGNAL */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ANT_NUM, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_SIGNAL, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_SNR, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_NF, |
| |
| /* Sub-attributes for IFACE_BSS */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_RSSI_BEACON, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_SNR_BEACON, |
| |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_REPORT_TIME, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_MEASUREMENT_TIME, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PAD, |
| |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_LAST, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_MAX = |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_LAST - 1 |
| }; |
| |
| /* Attributes for FTM commands and events */ |
| |
| /** |
| * enum qca_wlan_vendor_attr_loc_capa - Indoor location capabilities |
| * |
| * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAGS: Various flags. See |
| * enum qca_wlan_vendor_attr_loc_capa_flags. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_SESSIONS: Maximum number |
| * of measurement sessions that can run concurrently. |
| * Default is one session (no session concurrency). |
| * @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_PEERS: The total number of unique |
| * peers that are supported in running sessions. For example, |
| * if the value is 8 and maximum number of sessions is 2, you can |
| * have one session with 8 unique peers, or 2 sessions with 4 unique |
| * peers each, and so on. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_BURSTS_EXP: Maximum number |
| * of bursts per peer, as an exponent (2^value). Default is 0, |
| * meaning no multi-burst support. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_MEAS_PER_BURST: Maximum number |
| * of measurement exchanges allowed in a single burst. |
| * @QCA_WLAN_VENDOR_ATTR_AOA_CAPA_SUPPORTED_TYPES: Supported AOA measurement |
| * types. A bit mask (unsigned 32 bit value), each bit corresponds |
| * to an AOA type as defined by enum qca_vendor_attr_aoa_type. |
| */ |
| enum qca_wlan_vendor_attr_loc_capa { |
| QCA_WLAN_VENDOR_ATTR_LOC_CAPA_INVALID, |
| QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAGS, |
| QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_SESSIONS, |
| QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_PEERS, |
| QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_BURSTS_EXP, |
| QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_MEAS_PER_BURST, |
| QCA_WLAN_VENDOR_ATTR_AOA_CAPA_SUPPORTED_TYPES, |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_LOC_CAPA_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_LOC_CAPA_MAX = |
| QCA_WLAN_VENDOR_ATTR_LOC_CAPA_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_loc_capa_flags: Indoor location capability flags |
| * |
| * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_RESPONDER: Set if driver |
| * can be configured as an FTM responder (for example, an AP that |
| * services FTM requests). QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER |
| * will be supported if set. |
| * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_INITIATOR: Set if driver |
| * can run FTM sessions. QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION |
| * will be supported if set. |
| * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_ASAP: Set if FTM responder |
| * supports immediate (ASAP) response. |
| * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA: Set if driver supports standalone |
| * AOA measurement using QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS. |
| * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA_IN_FTM: Set if driver supports |
| * requesting AOA measurements as part of an FTM session. |
| */ |
| enum qca_wlan_vendor_attr_loc_capa_flags { |
| QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_RESPONDER = 1 << 0, |
| QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_INITIATOR = 1 << 1, |
| QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_ASAP = 1 << 2, |
| QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA = 1 << 3, |
| QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA_IN_FTM = 1 << 4, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_ftm_peer_info: Information about |
| * a single peer in a measurement session. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MAC_ADDR: The MAC address of the peer. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAGS: Various flags related |
| * to measurement. See enum qca_wlan_vendor_attr_ftm_peer_meas_flags. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_PARAMS: Nested attribute of |
| * FTM measurement parameters, as specified by IEEE P802.11-REVmc/D7.0 |
| * 9.4.2.167. See enum qca_wlan_vendor_attr_ftm_meas_param for |
| * list of supported attributes. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_SECURE_TOKEN_ID: Initial token ID for |
| * secure measurement. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_AOA_BURST_PERIOD: Request AOA |
| * measurement every <value> bursts. If 0 or not specified, |
| * AOA measurements will be disabled for this peer. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_FREQ: Frequency in MHz where |
| * the measurement frames are exchanged. Optional; if not |
| * specified, try to locate the peer in the kernel scan |
| * results cache and use frequency from there. |
| */ |
| enum qca_wlan_vendor_attr_ftm_peer_info { |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_INVALID, |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_MAC_ADDR, |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAGS, |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_PARAMS, |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_SECURE_TOKEN_ID, |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_AOA_BURST_PERIOD, |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_FREQ, |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_MAX = |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_ftm_peer_meas_flags: Measurement request flags, |
| * per-peer |
| * |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_ASAP: If set, request |
| * immediate (ASAP) response from peer. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCI: If set, request |
| * LCI report from peer. The LCI report includes the absolute |
| * location of the peer in "official" coordinates (similar to GPS). |
| * See IEEE P802.11-REVmc/D7.0, 11.24.6.7 for more information. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCR: If set, request |
| * Location civic report from peer. The LCR includes the location |
| * of the peer in free-form format. See IEEE P802.11-REVmc/D7.0, |
| * 11.24.6.7 for more information. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_SECURE: If set, |
| * request a secure measurement. |
| * QCA_WLAN_VENDOR_ATTR_FTM_PEER_SECURE_TOKEN_ID must also be provided. |
| */ |
| enum qca_wlan_vendor_attr_ftm_peer_meas_flags { |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_ASAP = 1 << 0, |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCI = 1 << 1, |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCR = 1 << 2, |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_SECURE = 1 << 3, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_ftm_meas_param: Measurement parameters |
| * |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_MEAS_PER_BURST: Number of measurements |
| * to perform in a single burst. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_NUM_BURSTS_EXP: Number of bursts to |
| * perform, specified as an exponent (2^value). |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_DURATION: Duration of burst |
| * instance, as specified in IEEE P802.11-REVmc/D7.0, 9.4.2.167. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_PERIOD: Time between bursts, |
| * as specified in IEEE P802.11-REVmc/D7.0, 9.4.2.167. Must |
| * be larger than QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_DURATION. |
| */ |
| enum qca_wlan_vendor_attr_ftm_meas_param { |
| QCA_WLAN_VENDOR_ATTR_FTM_PARAM_INVALID, |
| QCA_WLAN_VENDOR_ATTR_FTM_PARAM_MEAS_PER_BURST, |
| QCA_WLAN_VENDOR_ATTR_FTM_PARAM_NUM_BURSTS_EXP, |
| QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_DURATION, |
| QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_PERIOD, |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_FTM_PARAM_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_FTM_PARAM_MAX = |
| QCA_WLAN_VENDOR_ATTR_FTM_PARAM_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_ftm_peer_result: Per-peer results |
| * |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MAC_ADDR: MAC address of the reported |
| * peer. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS: Status of measurement |
| * request for this peer. |
| * See enum qca_wlan_vendor_attr_ftm_peer_result_status. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAGS: Various flags related |
| * to measurement results for this peer. |
| * See enum qca_wlan_vendor_attr_ftm_peer_result_flags. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_VALUE_SECONDS: Specified when |
| * request failed and peer requested not to send an additional request |
| * for this number of seconds. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCI: LCI report when received |
| * from peer. In the format specified by IEEE P802.11-REVmc/D7.0, |
| * 9.4.2.22.10. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCR: Location civic report when |
| * received from peer. In the format specified by IEEE P802.11-REVmc/D7.0, |
| * 9.4.2.22.13. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS_PARAMS: Reported when peer |
| * overridden some measurement request parameters. See |
| * enum qca_wlan_vendor_attr_ftm_meas_param. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AOA_MEAS: AOA measurement |
| * for this peer. Same contents as @QCA_WLAN_VENDOR_ATTR_AOA_MEAS_RESULT. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS: Array of measurement |
| * results. Each entry is a nested attribute defined |
| * by enum qca_wlan_vendor_attr_ftm_meas. |
| */ |
| enum qca_wlan_vendor_attr_ftm_peer_result { |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_INVALID, |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MAC_ADDR, |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS, |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAGS, |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_VALUE_SECONDS, |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCI, |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCR, |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS_PARAMS, |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AOA_MEAS, |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS, |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MAX = |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_ftm_peer_result_status |
| * |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_OK: Request sent ok and results |
| * will be provided. Peer may have overridden some measurement parameters, |
| * in which case overridden parameters will be report by |
| * QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS_PARAM attribute. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INCAPABLE: Peer is incapable |
| * of performing the measurement request. No more results will be sent |
| * for this peer in this session. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_FAILED: Peer reported request |
| * failed, and requested not to send an additional request for number |
| * of seconds specified by QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_VALUE_SECONDS |
| * attribute. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INVALID: Request validation |
| * failed. Request was not sent over the air. |
| */ |
| enum qca_wlan_vendor_attr_ftm_peer_result_status { |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_OK, |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INCAPABLE, |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_FAILED, |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INVALID, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_ftm_peer_result_flags: Various flags |
| * for measurement result, per-peer |
| * |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAG_DONE: If set, |
| * measurement completed for this peer. No more results will be reported |
| * for this peer in this session. |
| */ |
| enum qca_wlan_vendor_attr_ftm_peer_result_flags { |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAG_DONE = 1 << 0, |
| }; |
| |
| /** |
| * enum qca_vendor_attr_loc_session_status: Session completion status code |
| * |
| * @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_OK: Session completed |
| * successfully. |
| * @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_ABORTED: Session aborted |
| * by request. |
| * @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_INVALID: Session request |
| * was invalid and was not started. |
| * @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_FAILED: Session had an error |
| * and did not complete normally (for example out of resources). |
| */ |
| enum qca_vendor_attr_loc_session_status { |
| QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_OK, |
| QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_ABORTED, |
| QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_INVALID, |
| QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_FAILED, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_ftm_meas: Single measurement data |
| * |
| * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T1: Time of departure (TOD) of FTM packet as |
| * recorded by responder, in picoseconds. |
| * See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T2: Time of arrival (TOA) of FTM packet at |
| * initiator, in picoseconds. |
| * See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T3: TOD of ACK packet as recorded by |
| * initiator, in picoseconds. |
| * See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T4: TOA of ACK packet at |
| * responder, in picoseconds. |
| * See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_RSSI: RSSI (signal level) as recorded |
| * during this measurement exchange. Optional and will be provided if |
| * the hardware can measure it. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOD_ERR: TOD error reported by |
| * responder. Not always provided. |
| * See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOA_ERR: TOA error reported by |
| * responder. Not always provided. |
| * See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOD_ERR: TOD error measured by |
| * initiator. Not always provided. |
| * See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOA_ERR: TOA error measured by |
| * initiator. Not always provided. |
| * See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PAD: Attribute used for padding for 64-bit |
| * alignment. |
| */ |
| enum qca_wlan_vendor_attr_ftm_meas { |
| QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INVALID, |
| QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T1, |
| QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T2, |
| QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T3, |
| QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T4, |
| QCA_WLAN_VENDOR_ATTR_FTM_MEAS_RSSI, |
| QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOD_ERR, |
| QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOA_ERR, |
| QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOD_ERR, |
| QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOA_ERR, |
| QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PAD, |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_FTM_MEAS_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_FTM_MEAS_MAX = |
| QCA_WLAN_VENDOR_ATTR_FTM_MEAS_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_aoa_type - AOA measurement type |
| * |
| * @QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE: Phase of the strongest |
| * CIR (channel impulse response) path for each antenna. |
| * @QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE_AMP: Phase and amplitude |
| * of the strongest CIR path for each antenna. |
| */ |
| enum qca_wlan_vendor_attr_aoa_type { |
| QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE, |
| QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE_AMP, |
| QCA_WLAN_VENDOR_ATTR_AOA_TYPE_MAX |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_encryption_test - Attributes to |
| * validate encryption engine |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_NEEDS_DECRYPTION: Flag attribute. |
| * This will be included if the request is for decryption; if not included, |
| * the request is treated as a request for encryption by default. |
| * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_CIPHER: Unsigned 32-bit value |
| * indicating the key cipher suite. Takes same values as |
| * NL80211_ATTR_KEY_CIPHER. |
| * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_KEYID: Unsigned 8-bit value |
| * Key Id to be used for encryption |
| * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_TK: Array of 8-bit values. |
| * Key (TK) to be used for encryption/decryption |
| * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_PN: Array of 8-bit values. |
| * Packet number to be specified for encryption/decryption |
| * 6 bytes for TKIP/CCMP/GCMP. |
| * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_DATA: Array of 8-bit values |
| * representing the 802.11 packet (header + payload + FCS) that |
| * needs to be encrypted/decrypted. |
| * Encrypted/decrypted response from the driver will also be sent |
| * to userspace with the same attribute. |
| */ |
| enum qca_wlan_vendor_attr_encryption_test { |
| QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_NEEDS_DECRYPTION, |
| QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_CIPHER, |
| QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_KEYID, |
| QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_TK, |
| QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_PN, |
| QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_DATA, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_MAX = |
| QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_AFTER_LAST - 1 |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_dmg_rf_sector_type - Type of |
| * sector for DMG RF sector operations. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_RX: RX sector |
| * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_TX: TX sector |
| */ |
| enum qca_wlan_vendor_attr_dmg_rf_sector_type { |
| QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_RX, |
| QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_TX, |
| QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_MAX |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_fw_state - State of firmware |
| * |
| * @QCA_WLAN_VENDOR_ATTR_FW_STATE_ERROR: FW is in bad state |
| * @QCA_WLAN_VENDOR_ATTR_FW_STATE_ACTIVE: FW is active |
| */ |
| enum qca_wlan_vendor_attr_fw_state { |
| QCA_WLAN_VENDOR_ATTR_FW_STATE_ERROR, |
| QCA_WLAN_VENDOR_ATTR_FW_STATE_ACTIVE, |
| QCA_WLAN_VENDOR_ATTR_FW_STATE_MAX |
| }; |
| |
| /** |
| * BRP antenna limit mode |
| * |
| * @QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_DISABLE: Disable BRP force |
| * antenna limit, BRP will be performed as usual. |
| * @QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_EFFECTIVE: Define maximal |
| * antennas limit. the hardware may use less antennas than the |
| * maximum limit. |
| * @QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_FORCE: The hardware will |
| * use exactly the specified number of antennas for BRP. |
| */ |
| enum qca_wlan_vendor_attr_brp_ant_limit_mode { |
| QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_DISABLE, |
| QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_EFFECTIVE, |
| QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_FORCE, |
| QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_MAX |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_dmg_rf_sector_cfg - Attributes for |
| * DMG RF sector configuration for a single RF module. |
| * The values are defined in a compact way which closely matches |
| * the way it is stored in HW registers. |
| * The configuration provides values for 32 antennas and 8 distribution |
| * amplifiers, and together describes the characteristics of the RF |
| * sector - such as a beam in some direction with some gain. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_MODULE_INDEX: Index |
| * of RF module for this configuration. |
| * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE0: Bit 0 of edge |
| * amplifier gain index. Unsigned 32 bit number containing |
| * bits for all 32 antennas. |
| * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE1: Bit 1 of edge |
| * amplifier gain index. Unsigned 32 bit number containing |
| * bits for all 32 antennas. |
| * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE2: Bit 2 of edge |
| * amplifier gain index. Unsigned 32 bit number containing |
| * bits for all 32 antennas. |
| * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_PSH_HI: Phase values |
| * for first 16 antennas, 2 bits per antenna. |
| * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_PSH_LO: Phase values |
| * for last 16 antennas, 2 bits per antenna. |
| * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_DTYPE_X16: Contains |
| * DTYPE values (3 bits) for each distribution amplifier, followed |
| * by X16 switch bits for each distribution amplifier. There are |
| * total of 8 distribution amplifiers. |
| */ |
| enum qca_wlan_vendor_attr_dmg_rf_sector_cfg { |
| QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_MODULE_INDEX = 1, |
| QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE0 = 2, |
| QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE1 = 3, |
| QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE2 = 4, |
| QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_PSH_HI = 5, |
| QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_PSH_LO = 6, |
| QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_DTYPE_X16 = 7, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_MAX = |
| QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_AFTER_LAST - 1 |
| }; |
| |
| enum qca_wlan_vendor_attr_ll_stats_set { |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_INVALID = 0, |
| /* Unsigned 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_CONFIG_MPDU_SIZE_THRESHOLD = 1, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_CONFIG_AGGRESSIVE_STATS_GATHERING = 2, |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_MAX = |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * qca_wlan_ll_stats_clr_req_bitmap - Represents the bitmap to clear LL STATS |
| * values for %QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_REQ_MASK. |
| * |
| * @QCA_WLAN_LL_STATS_CLR_REQ_BITMAP_RADIO: Clear all radio statistics. |
| * |
| * @QCA_WLAN_LL_STATS_CLR_REQ_BITMAP_RADIO_CCA: Clear cca_busy_time within |
| * radio statistics. |
| * |
| * @QCA_WLAN_LL_STATS_CLR_REQ_BITMAP_RADIO_CHANNEL: Clear all channel |
| * statistics within radio statistics. |
| * |
| * @QCA_WLAN_LL_STATS_CLR_REQ_BITMAP_SCAN: Clear all scan statistics within |
| * radio statistics. |
| * |
| * @QCA_WLAN_LL_STATS_CLR_REQ_BITMAP_IFACE: Clear all interface statistics. |
| * |
| * @QCA_WLAN_LL_STATS_CLR_REQ_BITMAP_IFACE_TXRATE: Clear all TX rate statistics |
| * within interface statistics. |
| * |
| * @QCA_WLAN_LL_STATS_CLR_REQ_BITMAP_IFACE_AC: Clear all AC statistics within |
| * interface statistics. |
| * |
| * @QCA_WLAN_LL_STATS_CLR_REQ_BITMAP_IFACE_CONTENTION: Clear all contention |
| * (min, max, avg) statistics within AC statistics. |
| * |
| * @QCA_WLAN_LL_STATS_CLR_REQ_BITMAP_IFACE_ALL_PEER: Clear all peer statistics |
| * on this interface. |
| * |
| * @QCA_WLAN_LL_STATS_CLR_REQ_BITMAP_IFACE_PER_PEER: Clear particular peer |
| * statistics depending on the peer_mac. |
| */ |
| enum qca_wlan_ll_stats_clr_req_bitmap { |
| QCA_WLAN_LL_STATS_CLR_REQ_BITMAP_RADIO = BIT(0), |
| QCA_WLAN_LL_STATS_CLR_REQ_BITMAP_RADIO_CCA = BIT(1), |
| QCA_WLAN_LL_STATS_CLR_REQ_BITMAP_RADIO_CHANNELS = BIT(2), |
| QCA_WLAN_LL_STATS_CLR_REQ_BITMAP_RADIO_SCAN = BIT(3), |
| QCA_WLAN_LL_STATS_CLR_REQ_BITMAP_IFACE = BIT(4), |
| QCA_WLAN_LL_STATS_CLR_REQ_BITMAP_IFACE_TXRATE = BIT(5), |
| QCA_WLAN_LL_STATS_CLR_REQ_BITMAP_IFACE_AC = BIT(6), |
| QCA_WLAN_LL_STATS_CLR_REQ_BITMAP_IFACE_CONTENTION = BIT(7), |
| QCA_WLAN_LL_STATS_CLR_REQ_BITMAP_IFACE_ALL_PEER = BIT(8), |
| QCA_WLAN_LL_STATS_CLR_REQ_BITMAP_IFACE_PER_PEER = BIT(9), |
| }; |
| |
| enum qca_wlan_vendor_attr_ll_stats_clr { |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_INVALID = 0, |
| /* Unsigned 32bit bitmap for clearing statistics, specified |
| * in the enum qca_wlan_ll_stats_clr_req_bitmap. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_REQ_MASK = 1, |
| /* Unsigned 8 bit value: Request to stop statistics collection */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_STOP_REQ = 2, |
| |
| /* Unsigned 32 bit bitmap: Response from the driver |
| * for the cleared statistics |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_RSP_MASK = 3, |
| /* Unsigned 8 bit value: Response from driver/firmware |
| * for the stop request |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_STOP_RSP = 4, |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_MAX = |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * qca_wlan_ll_stats_get_req_bitmap - Represents the bitmap to request LL STATS |
| * values for %QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_CONFIG_REQ_MASK. |
| * |
| * @QCA_WLAN_LL_STATS_GET_REQ_BITMAP_RADIO: Request all radio statistics. |
| * |
| * @QCA_WLAN_LL_STATS_GET_REQ_BITMAP_IFACE: Request interface statistics. |
| * |
| * @QCA_WLAN_LL_STATS_GET_REQ_BITMAP_ALL_PEER: Request all peer statistics. |
| * |
| * @QCA_WLAN_LL_STATS_GET_REQ_BITMAP_PER_PEER: Request per peer statistics. |
| */ |
| enum qca_wlan_ll_stats_get_req_bitmap { |
| QCA_WLAN_LL_STATS_GET_REQ_BITMAP_RADIO = BIT(0), |
| QCA_WLAN_LL_STATS_GET_REQ_BITMAP_IFACE = BIT(1), |
| QCA_WLAN_LL_STATS_GET_REQ_BITMAP_ALL_PEER = BIT(2), |
| QCA_WLAN_LL_STATS_GET_REQ_BITMAP_PER_PEER = BIT(3), |
| }; |
| |
| enum qca_wlan_vendor_attr_ll_stats_get { |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_INVALID = 0, |
| /* Unsigned 32 bit value provided by the caller issuing the GET stats |
| * command. When reporting the stats results, the driver uses the same |
| * value to indicate which GET request the results correspond to. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_CONFIG_REQ_ID = 1, |
| /* Unsigned 32 bit value - bit mask to identify what statistics are |
| * requested for retrieval specified in the enum |
| * qca_wlan_ll_stats_get_req_bitmap |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_CONFIG_REQ_MASK = 2, |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_MAX = |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_AFTER_LAST - 1, |
| }; |
| |
| enum qca_wlan_vendor_attr_ll_stats_results { |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_INVALID = 0, |
| |
| /* |
| * For Multi Link Operation (MLO) connection, per-link statistics will |
| * be sent inside of %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK and |
| * cumulative statistics will be sent outside of |
| * %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK to maintain backward |
| * compatibility with legacy user space. Attributes which don't have |
| * explicit documentation for MLO will be sent only outside of |
| * %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK, such attributes values |
| * don't depend on whether the connection is MLO capable or not, e.g., |
| * radio and channel specific attributes. |
| */ |
| |
| /* Unsigned 32bit value. Used by the driver; must match the request id |
| * provided with the QCA_NL80211_VENDOR_SUBCMD_LL_STATS_GET command. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_RESULTS_REQ_ID = 1, |
| |
| /* Unsigned 32 bit value. For an MLO connection, indicates the value of |
| * the link with the best RSSI outside |
| * %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK and the link specific value |
| * inside %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_BEACON_RX = 2, |
| /* Unsigned 32 bit value. For an MLO connection, indicates the value of |
| * the link with the best RSSI outside |
| * %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK and the link specific value |
| * inside %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_MGMT_RX = 3, |
| /* Unsigned 32 bit value. For an MLO connection, indicates the value of |
| * the link with the best RSSI outside |
| * %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK and the link specific value |
| * inside %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_MGMT_ACTION_RX = 4, |
| /* Unsigned 32 bit value. For an MLO connection, indicates the value of |
| * the link with the best RSSI outside |
| * %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK and the link specific value |
| * inside %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_MGMT_ACTION_TX = 5, |
| /* Unsigned 32 bit value. For an MLO connection, indicates the value of |
| * the link with the best RSSI outside |
| * %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK and the link specific value |
| * inside %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RSSI_MGMT = 6, |
| /* Unsigned 32 bit value. For an MLO connection, indicates the value of |
| * the link with the best RSSI outside |
| * %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK and the link specific value |
| * inside %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RSSI_DATA = 7, |
| /* Unsigned 32 bit value. For an MLO connection, indicates the value of |
| * the link with the best RSSI outside |
| * %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK and the link specific value |
| * inside %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RSSI_ACK = 8, |
| |
| /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_* are |
| * nested within the interface stats. |
| */ |
| |
| /* Interface mode, e.g., STA, SOFTAP, IBSS, etc. |
| * Type = enum wifi_interface_mode. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_MODE = 9, |
| /* Interface MAC address. An array of 6 Unsigned int8 */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_MAC_ADDR = 10, |
| /* Type = enum wifi_connection_state, e.g., DISCONNECTED, |
| * AUTHENTICATING, etc. valid for STA, CLI only. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_STATE = 11, |
| /* Type = enum wifi_roam_state. Roaming state, e.g., IDLE or ACTIVE |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_ROAMING = 12, |
| /* Unsigned 32 bit value. WIFI_CAPABILITY_XXX */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_CAPABILITIES = 13, |
| /* NULL terminated SSID. An array of 33 Unsigned 8bit values */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_SSID = 14, |
| /* For non-MLO connection, BSSID of the AP. For MLO connection, MLD |
| * address of the AP. An array of 6 unsigned 8 bit values */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_BSSID = 15, |
| /* Country string advertised by AP. An array of 3 unsigned 8 bit |
| * values. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_AP_COUNTRY_STR = 16, |
| /* Country string for this association. An array of 3 unsigned 8 bit |
| * values. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_COUNTRY_STR = 17, |
| |
| /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_* could |
| * be nested within the interface stats. |
| * For an MLO connection, all %QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_* |
| * attributes except %QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_* |
| * indicate the aggregate of all links outside |
| * %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK. |
| * %QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_* attributes |
| * indicate value of the MLO link with the best RSSI outside |
| * %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK. |
| * These attributes indicate the link specific value inside |
| * %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK. |
| */ |
| |
| /* Type = enum wifi_traffic_ac, e.g., V0, VI, BE and BK */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_AC = 18, |
| /* Unsigned int 32 value corresponding to respective AC */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_TX_MPDU = 19, |
| /* Unsigned int 32 value corresponding to respective AC */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RX_MPDU = 20, |
| /* Unsigned int 32 value corresponding to respective AC */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_TX_MCAST = 21, |
| /* Unsigned int 32 value corresponding to respective AC */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RX_MCAST = 22, |
| /* Unsigned int 32 value corresponding to respective AC */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RX_AMPDU = 23, |
| /* Unsigned int 32 value corresponding to respective AC */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_TX_AMPDU = 24, |
| /* Unsigned int 32 value corresponding to respective AC */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_MPDU_LOST = 25, |
| /* Unsigned int 32 value corresponding to respective AC */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RETRIES = 26, |
| /* Unsigned int 32 value corresponding to respective AC */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RETRIES_SHORT = 27, |
| /* Unsigned int 32 values corresponding to respective AC */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RETRIES_LONG = 28, |
| /* Unsigned int 32 values corresponding to respective AC */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_TIME_MIN = 29, |
| /* Unsigned int 32 values corresponding to respective AC */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_TIME_MAX = 30, |
| /* Unsigned int 32 values corresponding to respective AC */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_TIME_AVG = 31, |
| /* Unsigned int 32 values corresponding to respective AC */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_NUM_SAMPLES = 32, |
| /* Unsigned 32 bit value. Number of peers */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_NUM_PEERS = 33, |
| |
| /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_* are |
| * nested within the interface stats. |
| */ |
| |
| /* Type = enum wifi_peer_type. Peer type, e.g., STA, AP, P2P GO etc. */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_TYPE = 34, |
| /* MAC addr corresponding to respective peer. An array of 6 unsigned |
| * 8 bit values. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_MAC_ADDRESS = 35, |
| /* Unsigned int 32 bit value representing capabilities corresponding |
| * to respective peer. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_CAPABILITIES = 36, |
| /* Unsigned 32 bit value. Number of rates */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_NUM_RATES = 37, |
| |
| /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_* |
| * are nested within the rate stat. |
| */ |
| |
| /* Wi-Fi Rate - separate attributes defined for individual fields */ |
| |
| /* Unsigned int 8 bit value; 0: OFDM, 1:CCK, 2:HT 3:VHT 4..7 reserved */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_PREAMBLE = 38, |
| /* Unsigned int 8 bit value; 0:1x1, 1:2x2, 3:3x3, 4:4x4 */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_NSS = 39, |
| /* Unsigned int 8 bit value; 0:20 MHz, 1:40 MHz, 2:80 MHz, 3:160 MHz */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_BW = 40, |
| /* Unsigned int 8 bit value; OFDM/CCK rate code would be as per IEEE Std |
| * in the units of 0.5 Mbps HT/VHT it would be MCS index |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_MCS_INDEX = 41, |
| |
| /* Unsigned 32 bit value. Bit rate in units of 100 kbps */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_BIT_RATE = 42, |
| |
| /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_STAT_* could be |
| * nested within the peer info stats. |
| */ |
| |
| /* Unsigned int 32 bit value. Number of successfully transmitted data |
| * packets, i.e., with ACK received corresponding to the respective |
| * rate. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_TX_MPDU = 43, |
| /* Unsigned int 32 bit value. Number of received data packets |
| * corresponding to the respective rate. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RX_MPDU = 44, |
| /* Unsigned int 32 bit value. Number of data packet losses, i.e., no ACK |
| * received corresponding to the respective rate. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_MPDU_LOST = 45, |
| /* Unsigned int 32 bit value. Total number of data packet retries for |
| * the respective rate. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RETRIES = 46, |
| /* Unsigned int 32 bit value. Total number of short data packet retries |
| * for the respective rate. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RETRIES_SHORT = 47, |
| /* Unsigned int 32 bit value. Total number of long data packet retries |
| * for the respective rate. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RETRIES_LONG = 48, |
| |
| /* Unsigned 32 bit value. This is used to indicate radio ID of the radio |
| * statistics when %QCA_WLAN_VENDOR_ATTR_LL_STATS_TYPE is |
| * %QCA_WLAN_VENDOR_ATTR_LL_STATS_TYPE_RADIO. This is also used |
| * inside %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK to indicate radio ID |
| * of the MLO link. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ID = 49, |
| /* Unsigned 32 bit value. Total number of msecs the radio is awake |
| * accruing over time. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME = 50, |
| /* Unsigned 32 bit value. Total number of msecs the radio is |
| * transmitting accruing over time. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_TX_TIME = 51, |
| /* Unsigned 32 bit value. Total number of msecs the radio is in active |
| * receive accruing over time. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_RX_TIME = 52, |
| /* Unsigned 32 bit value. Total number of msecs the radio is awake due |
| * to all scan accruing over time. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_SCAN = 53, |
| /* Unsigned 32 bit value. Total number of msecs the radio is awake due |
| * to NAN accruing over time. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_NBD = 54, |
| /* Unsigned 32 bit value. Total number of msecs the radio is awake due |
| * to GSCAN accruing over time. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_GSCAN = 55, |
| /* Unsigned 32 bit value. Total number of msecs the radio is awake due |
| * to roam scan accruing over time. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_ROAM_SCAN = 56, |
| /* Unsigned 32 bit value. Total number of msecs the radio is awake due |
| * to PNO scan accruing over time. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_PNO_SCAN = 57, |
| /* Unsigned 32 bit value. Total number of msecs the radio is awake due |
| * to Hotspot 2.0 scans and GAS exchange accruing over time. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_HS20 = 58, |
| /* Unsigned 32 bit value. Number of channels. */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_NUM_CHANNELS = 59, |
| |
| /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_* could |
| * be nested within the channel stats. |
| */ |
| |
| /* Type = enum wifi_channel_width. Channel width, e.g., 20, 40, 80 */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_WIDTH = 60, |
| /* Unsigned 32 bit value. Primary 20 MHz channel. This is used to |
| * indicate the primary frequency of the channel when |
| * %QCA_WLAN_VENDOR_ATTR_LL_STATS_TYPE is |
| * %QCA_WLAN_VENDOR_ATTR_LL_STATS_TYPE_RADIO. This is also used inside |
| * %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK to indicate the frequency |
| * on which the MLO link is operating. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_CENTER_FREQ = 61, |
| /* Unsigned 32 bit value. Center frequency (MHz) first segment. */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_CENTER_FREQ0 = 62, |
| /* Unsigned 32 bit value. Center frequency (MHz) second segment. */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_CENTER_FREQ1 = 63, |
| |
| /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_* could be |
| * nested within the radio stats. |
| */ |
| |
| /* Unsigned int 32 bit value representing total number of msecs the |
| * radio is awake on that channel accruing over time, corresponding to |
| * the respective channel. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_ON_TIME = 64, |
| /* Unsigned int 32 bit value representing total number of msecs the CCA |
| * register is busy accruing over time corresponding to the respective |
| * channel. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_CCA_BUSY_TIME = 65, |
| |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_NUM_RADIOS = 66, |
| |
| /* Signifies the nested list of channel attributes |
| * QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_* |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_CH_INFO = 67, |
| |
| /* Signifies the nested list of peer info attributes |
| * QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_*. For MLO connection, |
| * this also contains %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK_ID to |
| * indicate on which link the peer is connected. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO = 68, |
| |
| /* Signifies the nested list of rate info attributes |
| * QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_* |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_RATE_INFO = 69, |
| |
| /* Signifies the nested list of wmm info attributes |
| * QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_* |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_INFO = 70, |
| |
| /* Unsigned 8 bit value. Used by the driver; if set to 1, it indicates |
| * that more stats, e.g., peers or radio, are to follow in the next |
| * QCA_NL80211_VENDOR_SUBCMD_LL_STATS_*_RESULTS event. |
| * Otherwise, it is set to 0. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_RESULTS_MORE_DATA = 71, |
| |
| /* Unsigned 64 bit value. For an MLO connection, indicates the value of |
| * the link with the best RSSI outside |
| * %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK and the link specific value |
| * inside %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_AVERAGE_TSF_OFFSET = 72, |
| |
| /* Unsigned 32 bit value. For an MLO connection, indicates the value of |
| * the link with the best RSSI outside |
| * %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK and the link specific value |
| * inside %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_LEAKY_AP_DETECTED = 73, |
| |
| /* Unsigned 32 bit value. For an MLO connection, indicates the value of |
| * the link with the best RSSI outside |
| * %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK and the link specific value |
| * inside %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_LEAKY_AP_AVG_NUM_FRAMES_LEAKED = 74, |
| |
| /* Unsigned 32 bit value. For an MLO connection, indicates the value of |
| * the link with the best RSSI outside |
| * %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK and the link specific value |
| * inside %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_LEAKY_AP_GUARD_TIME = 75, |
| |
| /* Unsigned 32 bit value */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_TYPE = 76, |
| |
| /* Unsigned 32 bit value */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_NUM_TX_LEVELS = 77, |
| |
| /* Number of msecs the radio spent in transmitting for each power level |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_TX_TIME_PER_LEVEL = 78, |
| |
| /* Unsigned 32 bit value. For an MLO connection, indicates the value of |
| * the link with the best RSSI outside |
| * %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK and the link specific value |
| * inside %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RTS_SUCC_CNT = 79, |
| /* Unsigned 32 bit value. For an MLO connection, indicates the value of |
| * the link with the best RSSI outside |
| * %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK and the link specific value |
| * inside %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RTS_FAIL_CNT = 80, |
| /* Unsigned 32 bit value. For an MLO connection, indicates the value of |
| * the link with the best RSSI outside |
| * %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK and the link specific value |
| * inside %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_PPDU_SUCC_CNT = 81, |
| /* Unsigned 32 bit value. For an MLO connection, indicates the value of |
| * the link with the best RSSI outside |
| * %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK and the link specific value |
| * inside %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_PPDU_FAIL_CNT = 82, |
| |
| /* Unsigned int 32 value. |
| * Pending MSDUs corresponding to respective AC. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_PENDING_MSDU = 83, |
| |
| /* u32 value representing total time in milliseconds for which the radio |
| * is transmitting on this channel. This attribute will be nested |
| * within QCA_WLAN_VENDOR_ATTR_LL_STATS_CH_INFO. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_TX_TIME = 84, |
| /* u32 value representing total time in milliseconds for which the radio |
| * is receiving all 802.11 frames intended for this device on this |
| * channel. This attribute will be nested within |
| * QCA_WLAN_VENDOR_ATTR_LL_STATS_CH_INFO. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_RX_TIME = 85, |
| /* u8 value representing the channel load percentage. Possible values |
| * are 0-100. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_LOAD_PERCENTAGE = 86, |
| /* u8 value representing the time slicing duty cycle percentage. |
| * Possible values are 0-100. For an MLO connection, indicates the value |
| * of the link with the best RSSI outside |
| * %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK and the link specific value |
| * inside %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_TS_DUTY_CYCLE = 87, |
| /* Unsigned 32 bit value. The number of Beacon frames which are received |
| * from the associated AP and indicate buffered unicast frame(s) for us |
| * in the TIM element. For an MLO connection, indicates the value of the |
| * link with the best RSSI outside |
| * %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK and the link specific value |
| * inside %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_TIM_BEACON = 88, |
| /* Unsigned 32 bit value. The total number of Beacon frames received |
| * from the associated AP that have wrongly indicated buffered unicast |
| * traffic in the TIM element for us. |
| * Below scenarios will be considered as wrong TIM element beacon: |
| * 1) The related TIM element is set in the beacon for STA but STA |
| * doesn’t receive any unicast data after this beacon. |
| * 2) The related TIM element is still set in the beacon for STA |
| * after STA has indicated power save exit by QoS Null Data frame. |
| * For an MLO connection, indicates the value of the link with the best |
| * RSSI outside %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK and the link |
| * specific value inside %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_TIM_BEACON_ERR = 89, |
| |
| /* Signed 32 bit value. It represents the noise floor calibration value. |
| * Possible values are -120~-50 dBm. For an MLO connection, indicates |
| * the value of the link with the best RSSI outside |
| * %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK and the link specific value |
| * inside %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_NF_CAL_VAL = 90, |
| |
| /* Attribute used for padding for 64-bit alignment */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_PAD = 91, |
| |
| /* Unsigned u8 value, link ID of an MLO link. Used inside nested |
| * attribute %QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK to represent the |
| * link ID of the MLO link for which the statistics are embedded in the |
| * nested attribute. Used inside nested attribute |
| * %QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO to represent the connected |
| * link ID of the peer. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK_ID = 92, |
| |
| /* A nested array of attributes for each MLO link, each containing |
| * per-link statistics of a multi link connection. The attributes used |
| * inside this nested attribute are defined in enum |
| * qca_wlan_vendor_attr_ll_stats_results. |
| * |
| * For non-MLO connection, this attribute is not present and the |
| * statistics will be sent outside this attribute (without nesting). |
| * |
| * For MLO connection, this attribute is present and also cumulative |
| * statistics of all the links will be sent outside of this attribute |
| * to be compatible with legacy user space. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK = 93, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_MAX = |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_AFTER_LAST - 1, |
| }; |
| |
| enum qca_wlan_vendor_attr_ll_stats_type { |
| QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_INVALID = 0, |
| QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_RADIO = 1, |
| QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_IFACE = 2, |
| QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_PEERS = 3, |
| |
| /* keep last */ |
| QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_AFTER_LAST, |
| QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_MAX = |
| QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_tdls_configuration - Attributes for |
| * TDLS configuration to the host driver. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TRIGGER_MODE: Configure the TDLS trigger |
| * mode in the host driver. enum qca_wlan_vendor_tdls_trigger_mode |
| * represents the different TDLS trigger modes. |
| * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_STATS_PERIOD: Duration (u32) within |
| * which QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_THRESHOLD number |
| * of packets shall meet the criteria for implicit TDLS setup. |
| * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_THRESHOLD: Number (u32) of Tx/Rx packets |
| * within a duration QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_STATS_PERIOD |
| * to initiate a TDLS setup. |
| * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_DISCOVERY_PERIOD: Time (u32) to initiate |
| * a TDLS Discovery to the peer. |
| * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_MAX_DISCOVERY_ATTEMPT: Max number (u32) of |
| * discovery attempts to know the TDLS capability of the peer. A peer is |
| * marked as TDLS not capable if there is no response for all the attempts. |
| * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_TIMEOUT: Represents a duration (u32) |
| * within which QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_PACKET_THRESHOLD |
| * number of TX / RX frames meet the criteria for TDLS teardown. |
| * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_PACKET_THRESHOLD: Minimum number (u32) |
| * of Tx/Rx packets within a duration |
| * QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_TIMEOUT to tear down a TDLS link. |
| * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_SETUP_RSSI_THRESHOLD: Threshold |
| * corresponding to the RSSI of the peer below which a TDLS setup is |
| * triggered. |
| * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TEARDOWN_RSSI_THRESHOLD: Threshold |
| * corresponding to the RSSI of the peer above which a TDLS teardown is |
| * triggered. |
| */ |
| enum qca_wlan_vendor_attr_tdls_configuration { |
| QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TRIGGER_MODE = 1, |
| |
| /* Attributes configuring the TDLS Implicit Trigger */ |
| QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_STATS_PERIOD = 2, |
| QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_THRESHOLD = 3, |
| QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_DISCOVERY_PERIOD = 4, |
| QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_MAX_DISCOVERY_ATTEMPT = 5, |
| QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_TIMEOUT = 6, |
| QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_PACKET_THRESHOLD = 7, |
| QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_SETUP_RSSI_THRESHOLD = 8, |
| QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TEARDOWN_RSSI_THRESHOLD = 9, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_MAX = |
| QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_AFTER_LAST - 1 |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_tdls_trigger_mode: Represents the TDLS trigger mode in |
| * the driver |
| * |
| * The following are the different values for |
| * QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TRIGGER_MODE. |
| * |
| * @QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXPLICIT: The trigger to initiate/teardown |
| * the TDLS connection to a respective peer comes from the user space. |
| * wpa_supplicant provides the commands TDLS_SETUP, TDLS_TEARDOWN, |
| * TDLS_DISCOVER to do this. |
| * @QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_IMPLICIT: Host driver triggers this TDLS |
| * setup/teardown to the eligible peer once the configured criteria |
| * (such as TX/RX threshold, RSSI) is met. The attributes |
| * in QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IMPLICIT_PARAMS correspond to |
| * the different configuration criteria for the TDLS trigger from the |
| * host driver. |
| * @QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXTERNAL: Enables the driver to trigger |
| * the TDLS setup / teardown through the implicit mode only to the |
| * configured MAC addresses (wpa_supplicant, with tdls_external_control=1, |
| * configures the MAC address through TDLS_SETUP / TDLS_TEARDOWN commands). |
| * External mode works on top of the implicit mode. Thus the host driver |
| * is expected to configure in TDLS Implicit mode too to operate in |
| * External mode. |
| * Configuring External mode alone without Implicit mode is invalid. |
| * |
| * All the above implementations work as expected only when the host driver |
| * advertises the capability WPA_DRIVER_FLAGS_TDLS_EXTERNAL_SETUP - representing |
| * that the TDLS message exchange is not internal to the host driver, but |
| * depends on wpa_supplicant to do the message exchange. |
| */ |
| enum qca_wlan_vendor_tdls_trigger_mode { |
| QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXPLICIT = 1 << 0, |
| QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_IMPLICIT = 1 << 1, |
| QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXTERNAL = 1 << 2, |
| }; |
| |
| /** |
| * enum qca_vendor_attr_sar_limits_selections - Source of SAR power limits |
| * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF0: Select SAR profile #0 |
| * that is hard-coded in the Board Data File (BDF). |
| * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF1: Select SAR profile #1 |
| * that is hard-coded in the Board Data File (BDF). |
| * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF2: Select SAR profile #2 |
| * that is hard-coded in the Board Data File (BDF). |
| * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF3: Select SAR profile #3 |
| * that is hard-coded in the Board Data File (BDF). |
| * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF4: Select SAR profile #4 |
| * that is hard-coded in the Board Data File (BDF). |
| * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_NONE: Do not select any |
| * source of SAR power limits, thereby disabling the SAR power |
| * limit feature. |
| * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_USER: Select the SAR power |
| * limits configured by %QCA_NL80211_VENDOR_SUBCMD_SET_SAR. |
| * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_V2_0: Select the SAR power |
| * limits version 2.0 configured by %QCA_NL80211_VENDOR_SUBCMD_SET_SAR. |
| * |
| * This enumerates the valid set of values that may be supplied for |
| * attribute %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT in an instance of |
| * the %QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS vendor command or in |
| * the response to an instance of the |
| * %QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS vendor command. |
| */ |
| enum qca_vendor_attr_sar_limits_selections { |
| QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF0 = 0, |
| QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF1 = 1, |
| QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF2 = 2, |
| QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF3 = 3, |
| QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF4 = 4, |
| QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_NONE = 5, |
| QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_USER = 6, |
| QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_V2_0 = 7, |
| }; |
| |
| /** |
| * enum qca_vendor_attr_sar_limits_spec_modulations - |
| * SAR limits specification modulation |
| * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_CCK - |
| * CCK modulation |
| * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_OFDM - |
| * OFDM modulation |
| * |
| * This enumerates the valid set of values that may be supplied for |
| * attribute %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION in an |
| * instance of attribute %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC in an |
| * instance of the %QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS vendor |
| * command or in the response to an instance of the |
| * %QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS vendor command. |
| */ |
| enum qca_vendor_attr_sar_limits_spec_modulations { |
| QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_CCK = 0, |
| QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_OFDM = 1, |
| }; |
| |
| /** |
| * enum qca_vendor_attr_sar_limits - Attributes for SAR power limits |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SAR_ENABLE: Optional (u32) value to |
| * select which SAR power limit table should be used. Valid |
| * values are enumerated in enum |
| * %qca_vendor_attr_sar_limits_selections. The existing SAR |
| * power limit selection is unchanged if this attribute is not |
| * present. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_NUM_SPECS: Optional (u32) value |
| * which specifies the number of SAR power limit specifications |
| * which will follow. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC: Nested array of SAR power |
| * limit specifications. The number of specifications is |
| * specified by @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_NUM_SPECS. Each |
| * specification contains a set of |
| * QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_* attributes. A |
| * specification is uniquely identified by the attributes |
| * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_BAND, |
| * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_CHAIN, and |
| * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION and always |
| * contains as a payload the attribute |
| * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT, |
| * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT_INDEX. |
| * Either %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT or |
| * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT_INDEX is |
| * needed based upon the value of |
| * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SAR_ENABLE. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_BAND: Optional (u32) value to |
| * indicate for which band this specification applies. Valid |
| * values are enumerated in enum %nl80211_band (although not all |
| * bands may be supported by a given device). If the attribute is |
| * not supplied then the specification will be applied to all |
| * supported bands. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_CHAIN: Optional (u32) value |
| * to indicate for which antenna chain this specification |
| * applies, i.e. 1 for chain 1, 2 for chain 2, etc. If the |
| * attribute is not supplied then the specification will be |
| * applied to all chains. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION: Optional (u32) |
| * value to indicate for which modulation scheme this |
| * specification applies. Valid values are enumerated in enum |
| * %qca_vendor_attr_sar_limits_spec_modulations. If the attribute |
| * is not supplied then the specification will be applied to all |
| * modulation schemes. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT: Required (u32) |
| * value to specify the actual power limit value in units of 0.5 |
| * dBm (i.e., a value of 11 represents 5.5 dBm). |
| * This is required, when %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT is |
| * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_USER. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT_INDEX: Required (u32) |
| * value to indicate SAR V2 indices (0 - 11) to select SAR V2 profiles. |
| * This is required, when %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT is |
| * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_V2_0. |
| * |
| * These attributes are used with %QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS |
| * and %QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS. |
| */ |
| enum qca_vendor_attr_sar_limits { |
| QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SAR_ENABLE = 1, |
| QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_NUM_SPECS = 2, |
| QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC = 3, |
| QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_BAND = 4, |
| QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_CHAIN = 5, |
| QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION = 6, |
| QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT = 7, |
| QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT_INDEX = 8, |
| |
| QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_MAX = |
| QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_AFTER_LAST - 1 |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_get_wifi_info: Attributes for data used by |
| * QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_INFO sub command. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_WIFI_INFO_DRIVER_VERSION: In a request this attribute |
| * should be set to any U8 value to indicate that the driver version |
| * should be returned. When enabled in this manner, in a response this |
| * attribute will contain a string representation of the driver version. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_WIFI_INFO_FIRMWARE_VERSION: In a request this attribute |
| * should be set to any U8 value to indicate that the firmware version |
| * should be returned. When enabled in this manner, in a response this |
| * attribute will contain a string representation of the firmware version. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_WIFI_INFO_RADIO_INDEX: In a request this attribute |
| * should be set to any U32 value to indicate that the current radio |
| * index should be returned. When enabled in this manner, in a response |
| * this attribute will contain a U32 radio index value. |
| * |
| */ |
| enum qca_wlan_vendor_attr_get_wifi_info { |
| QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_WIFI_INFO_DRIVER_VERSION = 1, |
| QCA_WLAN_VENDOR_ATTR_WIFI_INFO_FIRMWARE_VERSION = 2, |
| QCA_WLAN_VENDOR_ATTR_WIFI_INFO_RADIO_INDEX = 3, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_MAX = |
| QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_AFTER_LAST - 1, |
| }; |
| |
| /* |
| * enum qca_wlan_vendor_attr_wifi_logger_start: Attributes for data used by |
| * QCA_NL80211_VENDOR_SUBCMD_WIFI_LOGGER_START sub command. |
| */ |
| enum qca_wlan_vendor_attr_wifi_logger_start { |
| QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_RING_ID = 1, |
| QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_VERBOSE_LEVEL = 2, |
| QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_FLAGS = 3, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_GET_MAX = |
| QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_AFTER_LAST - 1, |
| }; |
| |
| enum qca_wlan_vendor_attr_logger_results { |
| QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_INVALID = 0, |
| |
| /* Unsigned 32-bit value; must match the request Id supplied by |
| * Wi-Fi HAL in the corresponding subcmd NL msg. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_REQUEST_ID = 1, |
| |
| /* Unsigned 32-bit value; used to indicate the size of memory |
| * dump to be allocated. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_MEMDUMP_SIZE = 2, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_MAX = |
| QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_scan_freq_list_type: Frequency list types |
| * |
| * @QCA_PREFERRED_SCAN_FREQ_LIST: The driver shall use the scan frequency list |
| * specified with attribute QCA_ATTR_ROAM_CONTROL_SCAN_FREQ_LIST as |
| * a preferred frequency list for roaming. |
| * |
| * @QCA_SPECIFIC_SCAN_FREQ_LIST: The driver shall use the frequency list |
| * specified with attribute QCA_ATTR_ROAM_CONTROL_SCAN_FREQ_LIST as |
| * a specific frequency list for roaming. |
| */ |
| enum qca_scan_freq_list_type { |
| QCA_PREFERRED_SCAN_FREQ_LIST = 1, |
| QCA_SPECIFIC_SCAN_FREQ_LIST = 2, |
| }; |
| |
| /** |
| * enum qca_vendor_attr_scan_freq_list_scheme: Frequency list scheme |
| * |
| * @QCA_ATTR_ROAM_CONTROL_SCAN_FREQ_LIST: Nested attribute of u32 values |
| * List of frequencies in MHz to be considered for a roam scan. |
| * |
| * @QCA_ATTR_ROAM_CONTROL_SCAN_FREQ_LIST_TYPE: Unsigned 32-bit value. |
| * Type of frequency list scheme being configured/gotten as defined by the |
| * enum qca_scan_freq_list_type. |
| */ |
| enum qca_vendor_attr_scan_freq_list_scheme { |
| QCA_ATTR_ROAM_CONTROL_SCAN_FREQ_LIST = 1, |
| QCA_ATTR_ROAM_CONTROL_SCAN_FREQ_LIST_TYPE = 2, |
| |
| /* keep last */ |
| QCA_ATTR_ROAM_CONTROL_SCAN_FREQ_LIST_SCHEME_AFTER_LAST, |
| QCA_ATTR_ROAM_CONTROL_SCAN_FREQ_LIST_SCHEME_MAX = |
| QCA_ATTR_ROAM_CONTROL_SCAN_FREQ_LIST_SCHEME_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_roam_scan_scheme: Scan scheme |
| * |
| * @QCA_ROAM_SCAN_SCHEME_NO_SCAN: No frequencies specified to scan. |
| * Indicates the driver to not scan on a Roam Trigger scenario, but |
| * disconnect. E.g., on a BTM request from the AP the driver/firmware shall |
| * disconnect from the current connected AP by notifying a failure |
| * code in the BTM response. |
| * |
| * @QCA_ROAM_SCAN_SCHEME_PARTIAL_SCAN: Indicates the driver/firmware to |
| * trigger partial frequency scans. These frequencies are the ones learned |
| * or maintained by the driver based on the probability of finding the |
| * BSSIDs in the ESS for which the roaming is triggered. |
| * |
| * @QCA_ROAM_SCAN_SCHEME_FULL_SCAN: Indicates the driver/firmware to |
| * trigger the scan on all the valid frequencies to find better |
| * candidates to roam. |
| */ |
| enum qca_roam_scan_scheme { |
| QCA_ROAM_SCAN_SCHEME_NO_SCAN = 0, |
| QCA_ROAM_SCAN_SCHEME_PARTIAL_SCAN = 1, |
| QCA_ROAM_SCAN_SCHEME_FULL_SCAN = 2, |
| }; |
| |
| /* |
| * enum qca_vendor_roam_triggers: Bitmap of roaming triggers |
| * |
| * @QCA_ROAM_TRIGGER_REASON_PER: Set if the roam has to be triggered based on |
| * a bad packet error rates (PER). |
| * @QCA_ROAM_TRIGGER_REASON_BEACON_MISS: Set if the roam has to be triggered |
| * based on beacon misses from the connected AP. |
| * @QCA_ROAM_TRIGGER_REASON_POOR_RSSI: Set if the roam has to be triggered |
| * due to poor RSSI of the connected AP. |
| * @QCA_ROAM_TRIGGER_REASON_BETTER_RSSI: Set if the roam has to be triggered |
| * upon finding a BSSID with a better RSSI than the connected BSSID. |
| * Here the RSSI of the current BSSID need not be poor. |
| * @QCA_ROAM_TRIGGER_REASON_PERIODIC: Set if the roam has to be triggered |
| * by triggering a periodic scan to find a better AP to roam. |
| * @QCA_ROAM_TRIGGER_REASON_DENSE: Set if the roam has to be triggered |
| * when the connected channel environment is too noisy/congested. |
| * @QCA_ROAM_TRIGGER_REASON_BTM: Set if the roam has to be triggered |
| * when BTM Request frame is received from the connected AP. |
| * @QCA_ROAM_TRIGGER_REASON_BSS_LOAD: Set if the roam has to be triggered |
| * when the channel utilization is goes above the configured threshold. |
| * @QCA_ROAM_TRIGGER_REASON_USER_TRIGGER: Set if the roam has to be triggered |
| * based on the request from the user (space). |
| * @QCA_ROAM_TRIGGER_REASON_DEAUTH: Set if the roam has to be triggered when |
| * device receives Deauthentication/Disassociation frame from connected AP. |
| * @QCA_ROAM_TRIGGER_REASON_IDLE: Set if the roam has to be triggered when the |
| * device is in idle state (no TX/RX) and suspend mode, if the current RSSI |
| * is determined to be a poor one. |
| * @QCA_ROAM_TRIGGER_REASON_TX_FAILURES: Set if the roam has to be triggered |
| * based on continuous TX Data frame failures to the connected AP. |
| * @QCA_ROAM_TRIGGER_REASON_EXTERNAL_SCAN: Set if the roam has to be triggered |
| * based on the scan results obtained from an external scan (not triggered |
| * to aim roaming). |
| * |
| * Set the corresponding roam trigger reason bit to consider it for roam |
| * trigger. |
| * Userspace can set multiple bits and send to the driver. The driver shall |
| * consider all of them to trigger/initiate a roam scan. |
| */ |
| enum qca_vendor_roam_triggers { |
| QCA_ROAM_TRIGGER_REASON_PER = 1 << 0, |
| QCA_ROAM_TRIGGER_REASON_BEACON_MISS = 1 << 1, |
| QCA_ROAM_TRIGGER_REASON_POOR_RSSI = 1 << 2, |
| QCA_ROAM_TRIGGER_REASON_BETTER_RSSI = 1 << 3, |
| QCA_ROAM_TRIGGER_REASON_PERIODIC = 1 << 4, |
| QCA_ROAM_TRIGGER_REASON_DENSE = 1 << 5, |
| QCA_ROAM_TRIGGER_REASON_BTM = 1 << 6, |
| QCA_ROAM_TRIGGER_REASON_BSS_LOAD = 1 << 7, |
| QCA_ROAM_TRIGGER_REASON_USER_TRIGGER = 1 << 8, |
| QCA_ROAM_TRIGGER_REASON_DEAUTH = 1 << 9, |
| QCA_ROAM_TRIGGER_REASON_IDLE = 1 << 10, |
| QCA_ROAM_TRIGGER_REASON_TX_FAILURES = 1 << 11, |
| QCA_ROAM_TRIGGER_REASON_EXTERNAL_SCAN = 1 << 12, |
| }; |
| |
| /* |
| * enum qca_vendor_roam_fail_reasons: Defines the various roam |
| * fail reasons. This enum value is used in |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_ROAM_FAIL_REASON attribute. |
| * |
| * @QCA_ROAM_FAIL_REASON_SCAN_NOT_ALLOWED: Roam module in the firmware is not |
| * able to trigger the scan. |
| * @QCA_ROAM_FAIL_REASON_NO_AP_FOUND: No roamable APs found during roam scan. |
| * @QCA_ROAM_FAIL_REASON_NO_CAND_AP_FOUND: No candidate APs found during roam |
| * scan. |
| * @QCA_ROAM_FAIL_REASON_HOST: Roam fail due to disconnect issued from host. |
| * @QCA_ROAM_FAIL_REASON_AUTH_SEND: Unable to send Authentication frame. |
| * @QCA_ROAM_FAIL_REASON_AUTH_RECV: Received Authentication frame with error |
| * status code. |
| * @QCA_ROAM_FAIL_REASON_NO_AUTH_RESP: Authentication frame not received. |
| * @QCA_ROAM_FAIL_REASON_REASSOC_SEND: Unable to send Reassociation Request |
| * frame. |
| * @QCA_ROAM_FAIL_REASON_REASSOC_RECV: Received Reassociation Response frame |
| * with error status code. |
| * @QCA_ROAM_FAIL_REASON_NO_REASSOC_RESP: Reassociation Response frame not |
| * received. |
| * @QCA_ROAM_FAIL_REASON_SCAN_FAIL: Scan module not able to start scan. |
| * @QCA_ROAM_FAIL_REASON_AUTH_NO_ACK: No ACK is received for Authentication |
| * frame. |
| * @QCA_ROAM_FAIL_REASON_AUTH_INTERNAL_DROP: Authentication frame is dropped |
| * internally before transmission. |
| * @QCA_ROAM_FAIL_REASON_REASSOC_NO_ACK: No ACK is received for Reassociation |
| * Request frame. |
| * @QCA_ROAM_FAIL_REASON_REASSOC_INTERNAL_DROP: Reassociation Request frame is |
| * dropped internally. |
| * @QCA_ROAM_FAIL_REASON_EAPOL_M1_TIMEOUT: EAPOL-Key M1 is not received and |
| * times out. |
| * @QCA_ROAM_FAIL_REASON_EAPOL_M2_SEND: Unable to send EAPOL-Key M2 frame. |
| * @QCA_ROAM_FAIL_REASON_EAPOL_M2_INTERNAL_DROP: EAPOL-Key M2 frame dropped |
| * internally. |
| * @QCA_ROAM_FAIL_REASON_EAPOL_M2_NO_ACK: No ACK is received for EAPOL-Key |
| * M2 frame. |
| * @QCA_ROAM_FAIL_REASON_EAPOL_M3_TIMEOUT: EAPOL-Key M3 frame is not received. |
| * @QCA_ROAM_FAIL_REASON_EAPOL_M4_SEND: Unable to send EAPOL-Key M4 frame. |
| * @QCA_ROAM_FAIL_REASON_EAPOL_M4_INTERNAL_DROP: EAPOL-Key M4 frame dropped |
| * internally. |
| * @QCA_ROAM_FAIL_REASON_EAPOL_M4_NO_ACK: No ACK is received for EAPOL-Key M4 |
| * frame. |
| * @QCA_ROAM_FAIL_REASON_NO_SCAN_FOR_FINAL_BEACON_MISS: Roam scan is not |
| * started for final beacon miss case. |
| * @QCA_ROAM_FAIL_REASON_DISCONNECT: Deauthentication or Disassociation frame |
| * received from the AP during roaming handoff. |
| * @QCA_ROAM_FAIL_REASON_RESUME_ABORT: Firmware roams to the AP when the Apps |
| * or host is suspended and gives the indication of the last roamed AP only |
| * when the Apps is resumed. If the Apps is resumed while the roaming is in |
| * progress, this ongoing roaming is aborted and the last roamed AP is |
| * indicated to host. |
| * @QCA_ROAM_FAIL_REASON_SAE_INVALID_PMKID: WPA3-SAE invalid PMKID. |
| * @QCA_ROAM_FAIL_REASON_SAE_PREAUTH_TIMEOUT: WPA3-SAE pre-authentication times |
| * out. |
| * @QCA_ROAM_FAIL_REASON_SAE_PREAUTH_FAIL: WPA3-SAE pre-authentication fails. |
| * @QCA_ROAM_FAIL_REASON_CURR_AP_STILL_OK: Roam scan did not happen since the |
| * current network conditions are fine. |
| */ |
| enum qca_vendor_roam_fail_reasons { |
| QCA_ROAM_FAIL_REASON_NONE = 0, |
| QCA_ROAM_FAIL_REASON_SCAN_NOT_ALLOWED = 1, |
| QCA_ROAM_FAIL_REASON_NO_AP_FOUND = 2, |
| QCA_ROAM_FAIL_REASON_NO_CAND_AP_FOUND = 3, |
| QCA_ROAM_FAIL_REASON_HOST = 4, |
| QCA_ROAM_FAIL_REASON_AUTH_SEND = 5, |
| QCA_ROAM_FAIL_REASON_AUTH_RECV = 6, |
| QCA_ROAM_FAIL_REASON_NO_AUTH_RESP = 7, |
| QCA_ROAM_FAIL_REASON_REASSOC_SEND = 8, |
| QCA_ROAM_FAIL_REASON_REASSOC_RECV = 9, |
| QCA_ROAM_FAIL_REASON_NO_REASSOC_RESP = 10, |
| QCA_ROAM_FAIL_REASON_SCAN_FAIL = 11, |
| QCA_ROAM_FAIL_REASON_AUTH_NO_ACK = 12, |
| QCA_ROAM_FAIL_REASON_AUTH_INTERNAL_DROP = 13, |
| QCA_ROAM_FAIL_REASON_REASSOC_NO_ACK = 14, |
| QCA_ROAM_FAIL_REASON_REASSOC_INTERNAL_DROP = 15, |
| QCA_ROAM_FAIL_REASON_EAPOL_M1_TIMEOUT = 16, |
| QCA_ROAM_FAIL_REASON_EAPOL_M2_SEND = 17, |
| QCA_ROAM_FAIL_REASON_EAPOL_M2_INTERNAL_DROP = 18, |
| QCA_ROAM_FAIL_REASON_EAPOL_M2_NO_ACK = 19, |
| QCA_ROAM_FAIL_REASON_EAPOL_M3_TIMEOUT = 20, |
| QCA_ROAM_FAIL_REASON_EAPOL_M4_SEND = 21, |
| QCA_ROAM_FAIL_REASON_EAPOL_M4_INTERNAL_DROP = 22, |
| QCA_ROAM_FAIL_REASON_EAPOL_M4_NO_ACK = 23, |
| QCA_ROAM_FAIL_REASON_NO_SCAN_FOR_FINAL_BEACON_MISS = 24, |
| QCA_ROAM_FAIL_REASON_DISCONNECT = 25, |
| QCA_ROAM_FAIL_REASON_RESUME_ABORT = 26, |
| QCA_ROAM_FAIL_REASON_SAE_INVALID_PMKID = 27, |
| QCA_ROAM_FAIL_REASON_SAE_PREAUTH_TIMEOUT = 28, |
| QCA_ROAM_FAIL_REASON_SAE_PREAUTH_FAIL = 29, |
| QCA_ROAM_FAIL_REASON_CURR_AP_STILL_OK = 30, |
| }; |
| |
| /* |
| * enum qca_vendor_roam_invoke_fail_reasons: Defines the various roam |
| * invoke fail reasons. This enum value is used in |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_ROAM_INVOKE_FAIL_REASON attribute. |
| * |
| * @QCA_ROAM_INVOKE_STATUS_IFACE_INVALID: Invalid interface ID is passed |
| * in roam invoke command. |
| * @QCA_ROAM_INVOKE_STATUS_OFFLOAD_DISABLE: Roam offload in firmware is not |
| * enabled. |
| * @QCA_ROAM_INVOKE_STATUS_AP_SSID_LENGTH_INVALID: Connected AP profile SSID |
| * length is invalid. |
| * @QCA_ROAM_INVOKE_STATUS_ROAM_DISALLOW: Firmware internal roaming is already |
| * in progress. |
| * @QCA_ROAM_INVOKE_STATUS_NON_ROAMABLE_AP: Host sends the Beacon/Probe Response |
| * of the AP in the roam invoke command to firmware. This reason is sent by the |
| * firmware when the given AP is configured to be ignored or SSID/security |
| * does not match. |
| * @QCA_ROAM_INVOKE_STATUS_ROAM_INTERNAL_FAIL: Roam handoff failed because of |
| * firmware internal reasons. |
| * @QCA_ROAM_INVOKE_STATUS_DISALLOW: Roam invoke trigger is not enabled. |
| * @QCA_ROAM_INVOKE_STATUS_SCAN_FAIL: Scan start fail for roam invoke. |
| * @QCA_ROAM_INVOKE_STATUS_START_ROAM_FAIL: Roam handoff start fail. |
| * @QCA_ROAM_INVOKE_STATUS_INVALID_PARAMS: Roam invoke parameters are invalid. |
| * @QCA_ROAM_INVOKE_STATUS_NO_CAND_AP: No candidate AP found to roam to. |
| * @QCA_ROAM_INVOKE_STATUS_ROAM_FAIL: Roam handoff failed. |
| */ |
| enum qca_vendor_roam_invoke_fail_reasons { |
| QCA_ROAM_INVOKE_STATUS_NONE = 0, |
| QCA_ROAM_INVOKE_STATUS_IFACE_INVALID = 1, |
| QCA_ROAM_INVOKE_STATUS_OFFLOAD_DISABLE = 2, |
| QCA_ROAM_INVOKE_STATUS_AP_SSID_LENGTH_INVALID = 3, |
| QCA_ROAM_INVOKE_STATUS_ROAM_DISALLOW = 4, |
| QCA_ROAM_INVOKE_STATUS_NON_ROAMABLE_AP = 5, |
| QCA_ROAM_INVOKE_STATUS_ROAM_INTERNAL_FAIL = 6, |
| QCA_ROAM_INVOKE_STATUS_DISALLOW = 7, |
| QCA_ROAM_INVOKE_STATUS_SCAN_FAIL = 8, |
| QCA_ROAM_INVOKE_STATUS_START_ROAM_FAIL = 9, |
| QCA_ROAM_INVOKE_STATUS_INVALID_PARAMS = 10, |
| QCA_ROAM_INVOKE_STATUS_NO_CAND_AP = 11, |
| QCA_ROAM_INVOKE_STATUS_ROAM_FAIL = 12, |
| |
| }; |
| |
| /** |
| * enum qca_vendor_attr_roam_candidate_selection_criteria: |
| * |
| * Each attribute carries a weightage in percentage (%). |
| * |
| * @QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_RSSI: Unsigned 8-bit value. |
| * Represents the weightage to be given for the RSSI selection |
| * criteria among other parameters. |
| * |
| * @QCA_ATTR_ROAM_CAND_SEL_CRITERIA_RATE: Unsigned 8-bit value. |
| * Represents the weightage to be given for the rate selection |
| * criteria among other parameters. |
| * |
| * @QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_BW: Unsigned 8-bit value. |
| * Represents the weightage to be given for the band width selection |
| * criteria among other parameters. |
| * |
| * @QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_BAND: Unsigned 8-bit value. |
| * Represents the weightage to be given for the band selection |
| * criteria among other parameters. |
| * |
| * @QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_NSS: Unsigned 8-bit value. |
| * Represents the weightage to be given for the NSS selection |
| * criteria among other parameters. |
| * |
| * @QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_CHAN_CONGESTION: Unsigned 8-bit value. |
| * Represents the weightage to be given for the channel congestion |
| * selection criteria among other parameters. |
| * |
| * @QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_BEAMFORMING: Unsigned 8-bit value. |
| * Represents the weightage to be given for the beamforming selection |
| * criteria among other parameters. |
| * |
| * @QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_OCE_WAN: Unsigned 8-bit value. |
| * Represents the weightage to be given for the OCE selection |
| * criteria among other parameters. |
| */ |
| enum qca_vendor_attr_roam_candidate_selection_criteria { |
| QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_RSSI = 1, |
| QCA_ATTR_ROAM_CAND_SEL_CRITERIA_RATE = 2, |
| QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_BW = 3, |
| QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_BAND = 4, |
| QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_NSS = 5, |
| QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_CHAN_CONGESTION = 6, |
| QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_BEAMFORMING = 7, |
| QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_OCE_WAN = 8, |
| |
| /* keep last */ |
| QCA_ATTR_ROAM_CAND_SEL_CRITERIA_RATE_AFTER_LAST, |
| QCA_ATTR_ROAM_CAND_SEL_CRITERIA_RATE_MAX = |
| QCA_ATTR_ROAM_CAND_SEL_CRITERIA_RATE_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_vendor_attr_roam_control - Attributes to carry roam configuration |
| * The following attributes are used to set/get/clear the respective |
| * configurations to/from the driver. |
| * For the get, the attribute for the configuration to be queried shall |
| * carry any of its acceptable values to the driver. In return, the driver |
| * shall send the configured values within the same attribute to the user |
| * space. |
| * |
| * @QCA_ATTR_ROAM_CONTROL_ENABLE: Unsigned 8-bit value. |
| * Signifies to enable/disable roam control in driver. |
| * 1-enable, 0-disable |
| * Enable: Mandates the driver to do the further roams using the |
| * configuration parameters set through |
| * QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_SET. |
| * Disable: Disables the driver/firmware roaming triggered through |
| * QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_SET. Further roaming is |
| * expected to continue with the default configurations. |
| * |
| * @QCA_ATTR_ROAM_CONTROL_STATUS: Unsigned 8-bit value. |
| * This is used along with QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_GET. |
| * Roam control status is obtained through this attribute. |
| * |
| * @QCA_ATTR_ROAM_CONTROL_CLEAR_ALL: Flag attribute to indicate the |
| * complete config set through QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_SET |
| * is to be cleared in the driver. |
| * This is used along with QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_CLEAR |
| * and shall be ignored if used with other sub commands. |
| * If this attribute is specified along with subcmd |
| * QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_CLEAR, the driver shall ignore |
| * all other attributes, if there are any. |
| * If this attribute is not specified when the subcmd |
| * QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_CLEAR is sent, the driver shall |
| * clear the data corresponding to the attributes specified. |
| * |
| * @QCA_ATTR_ROAM_CONTROL_FREQ_LIST_SCHEME: Nested attribute to carry the |
| * list of frequencies and its type, represented by |
| * enum qca_vendor_attr_scan_freq_list_scheme. |
| * Frequency list and its type are mandatory for this attribute to set |
| * the frequencies. |
| * Frequency type is mandatory for this attribute to get the frequencies |
| * and the frequency list is obtained through |
| * QCA_ATTR_ROAM_CONTROL_SCAN_FREQ_LIST. |
| * Frequency list type is mandatory for this attribute to clear the |
| * frequencies. |
| * |
| * @QCA_ATTR_ROAM_CONTROL_SCAN_PERIOD: Unsigned 32-bit value. |
| * Carries the value of scan period in seconds to set. |
| * The value of scan period is obtained with the same attribute for get. |
| * Clears the scan period in the driver when specified with clear command. |
| * Scan period is the idle time in seconds between each subsequent |
| * channel scans. |
| * |
| * @QCA_ATTR_ROAM_CONTROL_FULL_SCAN_PERIOD: Unsigned 32-bit value. |
| * Carries the value of full scan period in seconds to set. |
| * The value of full scan period is obtained with the same attribute for |
| * get. |
| * Clears the full scan period in the driver when specified with clear |
| * command. Full scan period is the idle period in seconds between two |
| * successive full channel roam scans. |
| * |
| * @QCA_ATTR_ROAM_CONTROL_TRIGGERS: Unsigned 32-bit value. |
| * Carries a bitmap of the roam triggers specified in |
| * enum qca_vendor_roam_triggers. |
| * The driver shall enable roaming by enabling corresponding roam triggers |
| * based on the trigger bits sent with this attribute. |
| * If this attribute is not configured, the driver shall proceed with |
| * default behavior. |
| * The bitmap configured is obtained with the same attribute for get. |
| * Clears the bitmap configured in driver when specified with clear |
| * command. |
| * |
| * @QCA_ATTR_ROAM_CONTROL_SELECTION_CRITERIA: Nested attribute signifying the |
| * weightage in percentage (%) to be given for each selection criteria. |
| * Different roam candidate selection criteria are represented by |
| * enum qca_vendor_attr_roam_candidate_selection_criteria. |
| * The driver shall select the roam candidate based on corresponding |
| * candidate selection scores sent. |
| * |
| * An empty nested attribute is used to indicate that no specific |
| * preference score/criteria is configured (i.e., to disable this mechanism |
| * in the set case and to show that the mechanism is disabled in the get |
| * case). |
| * |
| * Userspace can send multiple attributes out of this enum to the driver. |
| * Since this attribute represents the weight/percentage of preference for |
| * the respective selection criteria, it is preferred to configure 100% |
| * total weightage. The value in each attribute or cumulative weight of the |
| * values in all the nested attributes should not exceed 100%. The driver |
| * shall reject such configuration. |
| * |
| * If the weights configured through this attribute are less than 100%, |
| * the driver shall honor the weights (x%) passed for the corresponding |
| * selection criteria and choose/distribute rest of the weight (100-x)% |
| * for the other selection criteria, based on its internal logic. |
| * |
| * The selection criteria configured is obtained with the same |
| * attribute for get. |
| * |
| * Clears the selection criteria configured in the driver when specified |
| * with clear command. |
| * |
| * @QCA_ATTR_ROAM_CONTROL_SCAN_SCHEME: Unsigned 32-bit value. |
| * Represents value of the scan frequency scheme from enum |
| * qca_roam_scan_scheme. |
| * It's an optional attribute. If this attribute is not configured, the |
| * driver shall proceed with default behavior. |
| * |
| * @QCA_ATTR_ROAM_CONTROL_CONNECTED_RSSI_THRESHOLD: Signed 32-bit value in dBm, |
| * signifying the RSSI threshold of the current connected AP, indicating |
| * the driver to trigger roam only when the current connected AP's RSSI |
| * is less than this threshold. |
| * |
| * @QCA_ATTR_ROAM_CONTROL_CANDIDATE_RSSI_THRESHOLD: Signed 32-bit value in dBm, |
| * signifying the RSSI threshold of the candidate AP, indicating |
| * the driver to trigger roam only to the candidate AP with RSSI |
| * better than this threshold. If RSSI thresholds for candidate APs found |
| * in the 2.4 GHz, 5 GHz, and 6 GHz bands are configured separately using |
| * QCA_ATTR_ROAM_CONTROL_CANDIDATE_RSSI_THRESHOLD_2P4GHZ, |
| * QCA_ATTR_ROAM_CONTROL_CANDIDATE_RSSI_THRESHOLD_5GHZ, and/or |
| * QCA_ATTR_ROAM_CONTROL_CANDIDATE_RSSI_THRESHOLD_6GHZ, those values will |
| * take precedence over the value configured using the |
| * QCA_ATTR_ROAM_CONTROL_CANDIDATE_RSSI_THRESHOLD attribute. |
| * |
| * @QCA_ATTR_ROAM_CONTROL_USER_REASON: Unsigned 32-bit value. Represents the |
| * user defined reason code to be sent to the AP in response to AP's |
| * request to trigger the roam if the roaming cannot be triggered. |
| * Applies to all the scenarios of AP assisted roaming (e.g., BTM). |
| * |
| * @QCA_ATTR_ROAM_CONTROL_SCAN_SCHEME_TRIGGERS: Unsigned 32-bit value. |
| * Carries a bitmap of the roam triggers specified in |
| * enum qca_vendor_roam_triggers. |
| * Represents the roam triggers for which the specific scan scheme from |
| * enum qca_roam_scan_scheme has to be applied. |
| * It's an optional attribute. If this attribute is not configured, but |
| * QCA_ATTR_ROAM_CONTROL_SCAN_SCHEME is specified, the scan scheme |
| * specified through QCA_ATTR_ROAM_CONTROL_SCAN_SCHEME is applicable for |
| * all the roams. |
| * If both QCA_ATTR_ROAM_CONTROL_SCAN_SCHEME and |
| * QCA_ATTR_ROAM_CONTROL_SCAN_SCHEME_TRIGGERS are not specified, the |
| * driver shall proceed with the default behavior. |
| * |
| * @QCA_ATTR_ROAM_CONTROL_CANDIDATE_RSSI_THRESHOLD_2P4GHZ: Signed 32-bit value |
| * in dBm, signifying the RSSI threshold of the candidate AP found in the |
| * 2.4 GHz band. The driver/firmware shall trigger roaming to the candidate |
| * AP found in the 2.4 GHz band only if its RSSI value is better than this |
| * threshold. Optional attribute. If this attribute is not included, the |
| * threshold value specified by the |
| * QCA_ATTR_ROAM_CONTROL_CANDIDATE_RSSI_THRESHOLD attribute shall be used. |
| * |
| * @QCA_ATTR_ROAM_CONTROL_CANDIDATE_RSSI_THRESHOLD_5GHZ: Signed 32-bit value in |
| * dBm, signifying the RSSI threshold of the candidate AP found in the 5 |
| * GHz band. The driver/firmware shall trigger roaming to the candidate AP |
| * found in the 5 GHz band only if its RSSI value is better than this |
| * threshold. Optional attribute. If this attribute is not included, the |
| * threshold value specified by tge |
| * QCA_ATTR_ROAM_CONTROL_CANDIDATE_RSSI_THRESHOLD attribute shall be used. |
| * |
| * @QCA_ATTR_ROAM_CONTROL_CANDIDATE_RSSI_THRESHOLD_6GHZ: Signed 32-bit value in |
| * dBm, signifying the RSSI threshold of the candidate AP found in the 6 |
| * GHz band. The driver/firmware shall trigger roaming to the candidate AP |
| * found in the 6 GHz band only if its RSSI value is better than this |
| * threshold. Optional attribute. If this attribute is not included, the |
| * threshold value specified by the |
| * QCA_ATTR_ROAM_CONTROL_CANDIDATE_RSSI_THRESHOLD attribute shall be used. |
| * |
| * @QCA_ATTR_ROAM_CONTROL_BAND_MASK: Unsigned 32-bit value. |
| * Carries bitmask value of bits from &enum qca_set_band and represents |
| * all the bands in which roaming is allowed. The configuration is valid |
| * until next disconnection. If this attribute is not present, the |
| * existing configuration shall be used. By default, roaming is allowed on |
| * all bands supported by the local device. When the value is set to |
| * %QCA_SETBAND_AUTO, all supported bands shall be enabled. |
| * |
| * @QCA_ATTR_ROAM_CONTROL_ACTIVE_CH_DWELL_TIME: u16 value in milliseconds. |
| * Optional parameter. Scan dwell time for active channels in the 2.4/5 GHz |
| * bands. If this attribute is not configured, the driver shall proceed |
| * with default behavior. |
| * |
| * @QCA_ATTR_ROAM_CONTROL_PASSIVE_CH_DWELL_TIME: u16 value in milliseconds. |
| * Optional parameter. Scan dwell time for passive channels in the 5 GHz |
| * band. If this attribute is not configured, the driver shall proceed with |
| * default behavior. |
| * |
| * @QCA_ATTR_ROAM_CONTROL_HOME_CHANNEL_TIME: u16 value in milliseconds. |
| * Optional parameter. The minimum duration to stay on the connected AP |
| * channel during the channel scanning. If this attribute is not |
| * configured, the driver shall proceed with default behavior. |
| * |
| * @QCA_ATTR_ROAM_CONTROL_MAXIMUM_AWAY_TIME: u16 value in milliseconds. |
| * Optional parameter. The maximum duration for which the radio can scan |
| * foreign channels consecutively without coming back to home channel. If |
| * this attribute is not configured, the driver shall proceed with default |
| * behavior. |
| * |
| * @QCA_ATTR_ROAM_CONTROL_SCAN_6G_PSC_DWELL_TIME: u16 value in milliseconds. |
| * Optional parameter. Scan dwell time for 6G Preferred Scanning Channels. |
| * If this attribute is not configured, the driver shall proceed with |
| * default behavior. |
| * |
| * @QCA_ATTR_ROAM_CONTROL_SCAN_6G_NON_PSC_DWELL_TIME: u16 value in milliseconds. |
| * Optional parameter. Scan dwell time for 6G Non Preferred Scanning |
| * Channels. If this attribute is not configured, the driver shall proceed |
| * with default behavior. |
| * |
| * @QCA_ATTR_ROAM_CONTROL_RX_LINKSPEED_THRESHOLD: u16 value in Mbps. |
| * Optional parameter. RX link speed threshold to disable roaming. |
| * If the current RX link speed is above the threshold, roaming is not |
| * needed. If this attribute is not configured, or if it is set to 0, the |
| * driver will not consider the RX link speed in the roaming decision. |
| * |
| * @QCA_ATTR_ROAM_CONTROL_HO_DELAY_FOR_RX: u16 value in milliseconds. |
| * Optional parameter. This configuration delays hand-off by the |
| * specified duration to receive pending RX frames from the current BSS. |
| * |
| * @QCA_ATTR_ROAM_CONTROL_FULL_SCAN_NO_REUSE_PARTIAL_SCAN_FREQ: Unsigned 8-bit |
| * value. |
| * During the roam scan, if there are no desired APs found in the partial |
| * frequency list, an immediate full scan on all the supported frequencies |
| * is initiated as a fallback. This flag controls the frequency list |
| * creation for the full scan on the following lines. |
| * 1 - Full scan to exclude the frequencies that were already scanned by |
| * the previous partial scan. |
| * 0 - Full scan to include all the supported frequencies irrespective of |
| * the ones part of the earlier partial scan. |
| * If this flag is not specified, a full scan shall include all the |
| * supported frequencies irrespective of the ones part of an earlier |
| * partial scan. |
| * |
| * @QCA_ATTR_ROAM_CONTROL_FULL_SCAN_6GHZ_ONLY_ON_PRIOR_DISCOVERY: Unsigned 8-bit |
| * value. |
| * During the roam scan, if there are no desired APs found in the partial |
| * frequency list, an immediate full scan on all the supported frequencies |
| * is initiated as a fallback. This full scan would add the 2.4/5/6 GHz |
| * frequencies, including all PSC frequencies by default. This attribute |
| * controls the inclusion of the 6 GHz PSC frequencies for the full scan |
| * as following. |
| * 1 - Full scan to include the supported 6 GHz PSC frequencies only on the |
| * prior discovery of any 6 GHz frequency support in the environment. |
| * This discovery can happen through a prior RNR, 11k neighbor |
| * request, 11v BTM request, host scan, etc. |
| * 0 - Default behavior. Full scan to include all the supported 6 GHz |
| * PSC frequencies regardless of whether 6 GHz BSSs have been |
| * discovered. |
| * The default behavior if this flag is not specified is to include all |
| * the supported 6 GHz PSC frequencies in the roam full scan. |
| */ |
| enum qca_vendor_attr_roam_control { |
| QCA_ATTR_ROAM_CONTROL_ENABLE = 1, |
| QCA_ATTR_ROAM_CONTROL_STATUS = 2, |
| QCA_ATTR_ROAM_CONTROL_CLEAR_ALL = 3, |
| QCA_ATTR_ROAM_CONTROL_FREQ_LIST_SCHEME= 4, |
| QCA_ATTR_ROAM_CONTROL_SCAN_PERIOD = 5, |
| QCA_ATTR_ROAM_CONTROL_FULL_SCAN_PERIOD = 6, |
| QCA_ATTR_ROAM_CONTROL_TRIGGERS = 7, |
| QCA_ATTR_ROAM_CONTROL_SELECTION_CRITERIA = 8, |
| QCA_ATTR_ROAM_CONTROL_SCAN_SCHEME = 9, |
| QCA_ATTR_ROAM_CONTROL_CONNECTED_RSSI_THRESHOLD = 10, |
| QCA_ATTR_ROAM_CONTROL_CANDIDATE_RSSI_THRESHOLD = 11, |
| QCA_ATTR_ROAM_CONTROL_USER_REASON = 12, |
| QCA_ATTR_ROAM_CONTROL_SCAN_SCHEME_TRIGGERS = 13, |
| QCA_ATTR_ROAM_CONTROL_CANDIDATE_RSSI_THRESHOLD_2P4GHZ = 14, |
| QCA_ATTR_ROAM_CONTROL_CANDIDATE_RSSI_THRESHOLD_5GHZ = 15, |
| QCA_ATTR_ROAM_CONTROL_CANDIDATE_RSSI_THRESHOLD_6GHZ = 16, |
| QCA_ATTR_ROAM_CONTROL_BAND_MASK = 17, |
| QCA_ATTR_ROAM_CONTROL_ACTIVE_CH_DWELL_TIME = 18, |
| QCA_ATTR_ROAM_CONTROL_PASSIVE_CH_DWELL_TIME = 19, |
| QCA_ATTR_ROAM_CONTROL_HOME_CHANNEL_TIME = 20, |
| QCA_ATTR_ROAM_CONTROL_MAXIMUM_AWAY_TIME = 21, |
| QCA_ATTR_ROAM_CONTROL_SCAN_6G_PSC_DWELL_TIME = 22, |
| QCA_ATTR_ROAM_CONTROL_SCAN_6G_NON_PSC_DWELL_TIME = 23, |
| QCA_ATTR_ROAM_CONTROL_LINKSPEED_THRESHOLD = 24, |
| QCA_ATTR_ROAM_CONTROL_HO_DELAY_FOR_RX = 25, |
| QCA_ATTR_ROAM_CONTROL_FULL_SCAN_NO_REUSE_PARTIAL_SCAN_FREQ = 26, |
| QCA_ATTR_ROAM_CONTROL_FULL_SCAN_6GHZ_ONLY_ON_PRIOR_DISCOVERY = 27, |
| |
| /* keep last */ |
| QCA_ATTR_ROAM_CONTROL_AFTER_LAST, |
| QCA_ATTR_ROAM_CONTROL_MAX = |
| QCA_ATTR_ROAM_CONTROL_AFTER_LAST - 1, |
| }; |
| |
| /* |
| * enum qca_wlan_vendor_attr_roaming_config_params: Attributes for data used by |
| * QCA_NL80211_VENDOR_SUBCMD_ROAM sub command. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ROAMING_SUBCMD: Unsigned 32-bit value. |
| * Represents the different roam sub commands referred by |
| * enum qca_wlan_vendor_roaming_subcmd. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ROAMING_REQ_ID: Unsigned 32-bit value. |
| * Represents the Request ID for the specific set of commands. |
| * This also helps to map specific set of commands to the respective |
| * ID / client. e.g., helps to identify the user entity configuring the |
| * ignored BSSIDs and accordingly clear the respective ones with the |
| * matching ID. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_ALLOW_LIST_SSID_NUM_NETWORKS: Unsigned |
| * 32-bit value. Represents the number of allowlist SSIDs configured. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_ALLOW_LIST_SSID_LIST: Nested attribute |
| * to carry the list of allowlist SSIDs. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_ALLOW_LIST_SSID: SSID (binary attribute, |
| * 0..32 octets). Represents the allow list SSID. Allowlist SSIDs |
| * represent the list of SSIDs to which the firmware/driver can consider |
| * to roam to. |
| * |
| * The following PARAM_A_BAND_XX attributes are applied to 5GHz BSSIDs when |
| * comparing with a 2.4GHz BSSID. They are not applied when comparing two |
| * 5GHz BSSIDs.The following attributes are set through the Roaming SUBCMD - |
| * QCA_WLAN_VENDOR_ROAMING_SUBCMD_SET_GSCAN_ROAM_PARAMS. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_BOOST_THRESHOLD: Signed 32-bit |
| * value, RSSI threshold above which 5GHz RSSI is favored. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_PENALTY_THRESHOLD: Signed 32-bit |
| * value, RSSI threshold below which 5GHz RSSI is penalized. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_BOOST_FACTOR: Unsigned 32-bit |
| * value, factor by which 5GHz RSSI is boosted. |
| * boost=(RSSI_measured-5GHz_boost_threshold)*5GHz_boost_factor |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_PENALTY_FACTOR: Unsigned 32-bit |
| * value, factor by which 5GHz RSSI is penalized. |
| * penalty=(5GHz_penalty_threshold-RSSI_measured)*5GHz_penalty_factor |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_MAX_BOOST: Unsigned 32-bit |
| * value, maximum boost that can be applied to a 5GHz RSSI. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_LAZY_ROAM_HISTERESYS: Unsigned 32-bit |
| * value, boost applied to current BSSID to ensure the currently |
| * associated BSSID is favored so as to prevent ping-pong situations. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_ALERT_ROAM_RSSI_TRIGGER: Signed 32-bit |
| * value, RSSI below which "Alert" roam is enabled. |
| * "Alert" mode roaming - firmware is "urgently" hunting for another BSSID |
| * because the RSSI is low, or because many successive beacons have been |
| * lost or other bad link conditions. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_ENABLE: Unsigned 32-bit |
| * value. 1-Enable, 0-Disable. Represents "Lazy" mode, where |
| * firmware is hunting for a better BSSID or allow listed SSID even though |
| * the RSSI of the link is good. The parameters enabling the roaming are |
| * configured through the PARAM_A_BAND_XX attrbutes. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PREFS: Nested attribute, |
| * represents the BSSIDs preferred over others while evaluating them |
| * for the roaming. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_NUM_BSSID: Unsigned |
| * 32-bit value. Represents the number of preferred BSSIDs set. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_BSSID: 6-byte MAC |
| * address representing the BSSID to be preferred. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_RSSI_MODIFIER: Signed |
| * 32-bit value, representing the modifier to be applied to the RSSI of |
| * the BSSID for the purpose of comparing it with other roam candidate. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS: Nested attribute, |
| * represents the BSSIDs to get ignored for roaming. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_NUM_BSSID: Unsigned |
| * 32-bit value, represents the number of ignored BSSIDs. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_BSSID: 6-byte MAC |
| * address representing the ignored BSSID. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_HINT: Flag attribute, |
| * indicates this request to ignore the BSSID as a hint to the driver. The |
| * driver can select this BSSID in the worst case (when no other BSSIDs are |
| * better). |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_CONTROL: Nested attribute to |
| * set/get/clear the roam control config as |
| * defined @enum qca_vendor_attr_roam_control. |
| */ |
| enum qca_wlan_vendor_attr_roaming_config_params { |
| QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_INVALID = 0, |
| |
| QCA_WLAN_VENDOR_ATTR_ROAMING_SUBCMD = 1, |
| QCA_WLAN_VENDOR_ATTR_ROAMING_REQ_ID = 2, |
| |
| /* Attributes for wifi_set_ssid_allow_list */ |
| QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_ALLOW_LIST_SSID_NUM_NETWORKS = 3, |
| QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_ALLOW_LIST_SSID_LIST = 4, |
| QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_ALLOW_LIST_SSID = 5, |
| |
| /* Attributes for set_roam_params */ |
| QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_BOOST_THRESHOLD = 6, |
| QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_PENALTY_THRESHOLD = 7, |
| QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_BOOST_FACTOR = 8, |
| QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_PENALTY_FACTOR = 9, |
| QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_MAX_BOOST = 10, |
| QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_LAZY_ROAM_HISTERESYS = 11, |
| QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_ALERT_ROAM_RSSI_TRIGGER = 12, |
| |
| /* Attribute for set_lazy_roam */ |
| QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_ENABLE = 13, |
| |
| /* Attribute for set_lazy_roam with preferences */ |
| QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PREFS = 14, |
| QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_NUM_BSSID = 15, |
| QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_BSSID = 16, |
| QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_RSSI_MODIFIER = 17, |
| |
| /* Attribute for setting ignored BSSID parameters */ |
| QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS = 18, |
| QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_NUM_BSSID = 19, |
| QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_BSSID = 20, |
| /* Flag attribute indicates this entry as a hint */ |
| QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_HINT = 21, |
| |
| QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_CONTROL = 22, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_MAX = |
| QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_AFTER_LAST - 1, |
| }; |
| |
| /* old names for API compatibility */ |
| #define QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID_NUM_NETWORKS \ |
| QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_ALLOW_LIST_SSID_NUM_NETWORKS |
| #define QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID_LIST \ |
| QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_ALLOW_LIST_SSID_LIST |
| #define QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID \ |
| QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_ALLOW_LIST_SSID |
| |
| /* |
| * enum qca_wlan_vendor_roaming_subcmd: Referred by |
| * QCA_WLAN_VENDOR_ATTR_ROAMING_SUBCMD. |
| * |
| * @QCA_WLAN_VENDOR_ROAMING_SUBCMD_SSID_ALLOW_LIST: Sub command to |
| * configure the allow list SSIDs. These are configured through |
| * the following attributes. |
| * QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_ALLOW_LIST_SSID_NUM_NETWORKS, |
| * QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_ALLOW_LIST_SSID_LIST, |
| * QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_ALLOW_LIST_SSID |
| * |
| * @QCA_WLAN_VENDOR_ROAMING_SUBCMD_SET_GSCAN_ROAM_PARAMS: Sub command to |
| * configure the Roam params. These parameters are evaluated on the GScan |
| * results. Refers the attributes PARAM_A_BAND_XX above to configure the |
| * params. |
| * |
| * @QCA_WLAN_VENDOR_ROAMING_SUBCMD_SET_LAZY_ROAM: Sets the Lazy roam. Uses |
| * the attribute QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_ENABLE |
| * to enable/disable Lazy roam. |
| * |
| * @QCA_WLAN_VENDOR_ROAMING_SUBCMD_SET_BSSID_PREFS: Sets the BSSID |
| * preference. Contains the attribute |
| * QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PREFS to set the BSSID |
| * preference. |
| * |
| * @QCA_WLAN_VENDOR_ROAMING_SUBCMD_SET_DENYLIST_BSSID: Sets the list of BSSIDs |
| * to ignore in roaming decision. Uses |
| * QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS to set the list. |
| * |
| * @QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_SET: Command to set the |
| * roam control config to the driver with the attribute |
| * QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_CONTROL. |
| * |
| * @QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_GET: Command to obtain the |
| * roam control config from driver with the attribute |
| * QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_CONTROL. |
| * For the get, the attribute for the configuration to be queried shall |
| * carry any of its acceptable value to the driver. In return, the driver |
| * shall send the configured values within the same attribute to the user |
| * space. |
| * |
| * @QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_CLEAR: Command to clear the |
| * roam control config in the driver with the attribute |
| * QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_CONTROL. |
| * The driver shall continue with its default roaming behavior when data |
| * corresponding to an attribute is cleared. |
| */ |
| enum qca_wlan_vendor_roaming_subcmd { |
| QCA_WLAN_VENDOR_ROAMING_SUBCMD_INVALID = 0, |
| QCA_WLAN_VENDOR_ROAMING_SUBCMD_SSID_ALLOW_LIST = 1, |
| QCA_WLAN_VENDOR_ROAMING_SUBCMD_SET_GSCAN_ROAM_PARAMS = 2, |
| QCA_WLAN_VENDOR_ROAMING_SUBCMD_SET_LAZY_ROAM = 3, |
| QCA_WLAN_VENDOR_ROAMING_SUBCMD_SET_BSSID_PREFS = 4, |
| QCA_WLAN_VENDOR_ROAMING_SUBCMD_SET_BSSID_PARAMS = 5, |
| QCA_WLAN_VENDOR_ROAMING_SUBCMD_SET_DENYLIST_BSSID = 6, |
| QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_SET = 7, |
| QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_GET = 8, |
| QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_CLEAR = 9, |
| }; |
| |
| /* old names for API compatibility */ |
| #define QCA_WLAN_VENDOR_ROAMING_SUBCMD_SSID_WHITE_LIST \ |
| QCA_WLAN_VENDOR_ROAMING_SUBCMD_SSID_ALLOW_LIST |
| #define QCA_WLAN_VENDOR_ROAMING_SUBCMD_SET_BLACKLIST_BSSID \ |
| QCA_WLAN_VENDOR_ROAMING_SUBCMD_SET_DENYLIST_BSSID |
| |
| enum qca_wlan_vendor_attr_gscan_config_params { |
| QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_INVALID = 0, |
| |
| /* Unsigned 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_REQUEST_ID = 1, |
| |
| /* Attributes for data used by |
| * QCA_NL80211_VENDOR_SUBCMD_GSCAN_GET_VALID_CHANNELS sub command. |
| */ |
| /* Unsigned 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_GET_VALID_CHANNELS_CONFIG_PARAM_WIFI_BAND |
| = 2, |
| /* Unsigned 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_GET_VALID_CHANNELS_CONFIG_PARAM_MAX_CHANNELS |
| = 3, |
| |
| /* Attributes for input params used by |
| * QCA_NL80211_VENDOR_SUBCMD_GSCAN_START sub command. |
| */ |
| |
| /* Unsigned 32-bit value; channel frequency */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_CHANNEL = 4, |
| /* Unsigned 32-bit value; dwell time in ms. */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_DWELL_TIME = 5, |
| /* Unsigned 8-bit value; 0: active; 1: passive; N/A for DFS */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_PASSIVE = 6, |
| /* Unsigned 8-bit value; channel class */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_CLASS = 7, |
| |
| /* Unsigned 8-bit value; bucket index, 0 based */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_INDEX = 8, |
| /* Unsigned 8-bit value; band. */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_BAND = 9, |
| /* Unsigned 32-bit value; desired period, in ms. */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_PERIOD = 10, |
| /* Unsigned 8-bit value; report events semantics. */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_REPORT_EVENTS = 11, |
| /* Unsigned 32-bit value. Followed by a nested array of |
| * GSCAN_CHANNEL_SPEC_* attributes. |
| */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_NUM_CHANNEL_SPECS = 12, |
| |
| /* Array of QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_* attributes. |
| * Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_NUM_CHANNEL_SPECS |
| */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC = 13, |
| |
| /* Unsigned 32-bit value; base timer period in ms. */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_BASE_PERIOD = 14, |
| /* Unsigned 32-bit value; number of APs to store in each scan in the |
| * BSSID/RSSI history buffer (keep the highest RSSI APs). |
| */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_MAX_AP_PER_SCAN = 15, |
| /* Unsigned 8-bit value; in %, when scan buffer is this much full, wake |
| * up AP. |
| */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_REPORT_THRESHOLD_PERCENT |
| = 16, |
| |
| /* Unsigned 8-bit value; number of scan bucket specs; followed by a |
| * nested array of_GSCAN_BUCKET_SPEC_* attributes and values. The size |
| * of the array is determined by NUM_BUCKETS. |
| */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_NUM_BUCKETS = 17, |
| |
| /* Array of QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_* attributes. |
| * Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_NUM_BUCKETS |
| */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC = 18, |
| |
| /* Unsigned 8-bit value */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_GET_CACHED_SCAN_RESULTS_CONFIG_PARAM_FLUSH |
| = 19, |
| /* Unsigned 32-bit value; maximum number of results to be returned. */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_GET_CACHED_SCAN_RESULTS_CONFIG_PARAM_MAX |
| = 20, |
| |
| /* An array of 6 x unsigned 8-bit value */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_BSSID = 21, |
| /* Signed 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_RSSI_LOW = 22, |
| /* Signed 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_RSSI_HIGH = 23, |
| /* Unsigned 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_CHANNEL = 24, |
| |
| /* Number of hotlist APs as unsigned 32-bit value, followed by a nested |
| * array of AP_THRESHOLD_PARAM attributes and values. The size of the |
| * array is determined by NUM_AP. |
| */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_BSSID_HOTLIST_PARAMS_NUM_AP = 25, |
| |
| /* Array of QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_* attributes. |
| * Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_NUM_CHANNEL_SPECS |
| */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM = 26, |
| |
| /* Unsigned 32-bit value; number of samples for averaging RSSI. */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_SIGNIFICANT_CHANGE_PARAMS_RSSI_SAMPLE_SIZE |
| = 27, |
| /* Unsigned 32-bit value; number of samples to confirm AP loss. */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_SIGNIFICANT_CHANGE_PARAMS_LOST_AP_SAMPLE_SIZE |
| = 28, |
| /* Unsigned 32-bit value; number of APs breaching threshold. */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_SIGNIFICANT_CHANGE_PARAMS_MIN_BREACHING = 29, |
| /* Unsigned 32-bit value; number of APs. Followed by an array of |
| * AP_THRESHOLD_PARAM attributes. Size of the array is NUM_AP. |
| */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_SIGNIFICANT_CHANGE_PARAMS_NUM_AP = 30, |
| /* Unsigned 32-bit value; number of samples to confirm AP loss. */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_BSSID_HOTLIST_PARAMS_LOST_AP_SAMPLE_SIZE |
| = 31, |
| /* Unsigned 32-bit value. If max_period is non zero or different than |
| * period, then this bucket is an exponential backoff bucket. |
| */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_MAX_PERIOD = 32, |
| /* Unsigned 32-bit value. */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_BASE = 33, |
| /* Unsigned 32-bit value. For exponential back off bucket, number of |
| * scans to perform for a given period. |
| */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_STEP_COUNT = 34, |
| /* Unsigned 8-bit value; in number of scans, wake up AP after these |
| * many scans. |
| */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_REPORT_THRESHOLD_NUM_SCANS |
| = 35, |
| |
| /* Attributes for data used by |
| * QCA_NL80211_VENDOR_SUBCMD_GSCAN_SET_SSID_HOTLIST sub command. |
| */ |
| /* Unsigned 3-2bit value; number of samples to confirm SSID loss. */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_HOTLIST_PARAMS_LOST_SSID_SAMPLE_SIZE |
| = 36, |
| /* Number of hotlist SSIDs as unsigned 32-bit value, followed by a |
| * nested array of SSID_THRESHOLD_PARAM_* attributes and values. The |
| * size of the array is determined by NUM_SSID. |
| */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_HOTLIST_PARAMS_NUM_SSID = 37, |
| /* Array of QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_* |
| * attributes. |
| * Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_HOTLIST_PARAMS_NUM_SSID |
| */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM = 38, |
| |
| /* An array of 33 x unsigned 8-bit value; NULL terminated SSID */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_SSID = 39, |
| /* Unsigned 8-bit value */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_BAND = 40, |
| /* Signed 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_RSSI_LOW = 41, |
| /* Signed 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_RSSI_HIGH = 42, |
| /* Unsigned 32-bit value; a bitmask with additional gscan config flag. |
| */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_CONFIGURATION_FLAGS = 43, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_MAX = |
| QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_AFTER_LAST - 1, |
| }; |
| |
| enum qca_wlan_vendor_attr_gscan_results { |
| QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_INVALID = 0, |
| |
| /* Unsigned 32-bit value; must match the request Id supplied by |
| * Wi-Fi HAL in the corresponding subcmd NL msg. |
| */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_REQUEST_ID = 1, |
| |
| /* Unsigned 32-bit value; used to indicate the status response from |
| * firmware/driver for the vendor sub-command. |
| */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_STATUS = 2, |
| |
| /* GSCAN Valid Channels attributes */ |
| /* Unsigned 32bit value; followed by a nested array of CHANNELS. */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_CHANNELS = 3, |
| /* An array of NUM_CHANNELS x unsigned 32-bit value integers |
| * representing channel numbers. |
| */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CHANNELS = 4, |
| |
| /* GSCAN Capabilities attributes */ |
| /* Unsigned 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_SCAN_CACHE_SIZE = 5, |
| /* Unsigned 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_SCAN_BUCKETS = 6, |
| /* Unsigned 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_AP_CACHE_PER_SCAN |
| = 7, |
| /* Unsigned 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_RSSI_SAMPLE_SIZE |
| = 8, |
| /* Signed 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_SCAN_REPORTING_THRESHOLD |
| = 9, |
| /* Unsigned 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_HOTLIST_BSSIDS = 10, |
| /* Unsigned 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_SIGNIFICANT_WIFI_CHANGE_APS |
| = 11, |
| /* Unsigned 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_BSSID_HISTORY_ENTRIES |
| = 12, |
| |
| /* GSCAN Attributes used with |
| * QCA_NL80211_VENDOR_SUBCMD_GSCAN_SCAN_RESULTS_AVAILABLE sub-command. |
| */ |
| |
| /* Unsigned 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE = 13, |
| |
| /* GSCAN attributes used with |
| * QCA_NL80211_VENDOR_SUBCMD_GSCAN_FULL_SCAN_RESULT sub-command. |
| */ |
| |
| /* An array of NUM_RESULTS_AVAILABLE x |
| * QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_* |
| */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST = 14, |
| |
| /* Unsigned 64-bit value; age of sample at the time of retrieval */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_TIME_STAMP = 15, |
| /* 33 x unsigned 8-bit value; NULL terminated SSID */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_SSID = 16, |
| /* An array of 6 x unsigned 8-bit value */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_BSSID = 17, |
| /* Unsigned 32-bit value; channel frequency in MHz */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_CHANNEL = 18, |
| /* Signed 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_RSSI = 19, |
| /* Unsigned 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_RTT = 20, |
| /* Unsigned 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_RTT_SD = 21, |
| /* Unsigned 16-bit value */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_BEACON_PERIOD = 22, |
| /* Unsigned 16-bit value */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_CAPABILITY = 23, |
| /* Unsigned 32-bit value; size of the IE DATA blob */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_IE_LENGTH = 24, |
| /* An array of IE_LENGTH x unsigned 8-bit value; blob of all the |
| * information elements found in the beacon; this data should be a |
| * packed list of wifi_information_element objects, one after the |
| * other. |
| */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_IE_DATA = 25, |
| |
| /* Unsigned 8-bit value; set by driver to indicate more scan results are |
| * available. |
| */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_MORE_DATA = 26, |
| |
| /* GSCAN attributes for |
| * QCA_NL80211_VENDOR_SUBCMD_GSCAN_SCAN_EVENT sub-command. |
| */ |
| /* Unsigned 8-bit value */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_EVENT_TYPE = 27, |
| /* Unsigned 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_EVENT_STATUS = 28, |
| |
| /* GSCAN attributes for |
| * QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_AP_FOUND sub-command. |
| */ |
| /* Use attr QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE |
| * to indicate number of results. |
| * Also, use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST to indicate the |
| * list of results. |
| */ |
| |
| /* GSCAN attributes for |
| * QCA_NL80211_VENDOR_SUBCMD_GSCAN_SIGNIFICANT_CHANGE sub-command. |
| */ |
| /* An array of 6 x unsigned 8-bit value */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_BSSID = 29, |
| /* Unsigned 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_CHANNEL |
| = 30, |
| /* Unsigned 32-bit value. */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_NUM_RSSI |
| = 31, |
| /* A nested array of signed 32-bit RSSI values. Size of the array is |
| * determined by (NUM_RSSI of SIGNIFICANT_CHANGE_RESULT_NUM_RSSI. |
| */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_RSSI_LIST |
| = 32, |
| |
| /* GSCAN attributes used with |
| * QCA_NL80211_VENDOR_SUBCMD_GSCAN_GET_CACHED_RESULTS sub-command. |
| */ |
| /* Use attr QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE |
| * to indicate number of gscan cached results returned. |
| * Also, use QCA_WLAN_VENDOR_ATTR_GSCAN_CACHED_RESULTS_LIST to indicate |
| * the list of gscan cached results. |
| */ |
| |
| /* An array of NUM_RESULTS_AVAILABLE x |
| * QCA_NL80211_VENDOR_ATTR_GSCAN_CACHED_RESULTS_* |
| */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_CACHED_RESULTS_LIST = 33, |
| /* Unsigned 32-bit value; a unique identifier for the scan unit. */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_CACHED_RESULTS_SCAN_ID = 34, |
| /* Unsigned 32-bit value; a bitmask w/additional information about scan. |
| */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_CACHED_RESULTS_FLAGS = 35, |
| /* Use attr QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE |
| * to indicate number of wifi scan results/bssids retrieved by the scan. |
| * Also, use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST to indicate the |
| * list of wifi scan results returned for each cached result block. |
| */ |
| |
| /* GSCAN attributes for |
| * QCA_NL80211_VENDOR_SUBCMD_PNO_NETWORK_FOUND sub-command. |
| */ |
| /* Use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE for |
| * number of results. |
| * Use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST to indicate the nested |
| * list of wifi scan results returned for each |
| * wifi_passpoint_match_result block. |
| * Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE. |
| */ |
| |
| /* GSCAN attributes for |
| * QCA_NL80211_VENDOR_SUBCMD_PNO_PASSPOINT_NETWORK_FOUND sub-command. |
| */ |
| /* Unsigned 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_NETWORK_FOUND_NUM_MATCHES |
| = 36, |
| /* A nested array of |
| * QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_* |
| * attributes. Array size = |
| * *_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_NETWORK_FOUND_NUM_MATCHES. |
| */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_RESULT_LIST = 37, |
| |
| /* Unsigned 32-bit value; network block id for the matched network */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_ID = 38, |
| /* Use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST to indicate the nested |
| * list of wifi scan results returned for each |
| * wifi_passpoint_match_result block. |
| */ |
| /* Unsigned 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_ANQP_LEN = 39, |
| /* An array size of PASSPOINT_MATCH_ANQP_LEN of unsigned 8-bit values; |
| * ANQP data in the information_element format. |
| */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_ANQP = 40, |
| |
| /* Unsigned 32-bit value; a GSCAN Capabilities attribute. */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_HOTLIST_SSIDS = 41, |
| /* Unsigned 32-bit value; a GSCAN Capabilities attribute. */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_NUM_EPNO_NETS = 42, |
| /* Unsigned 32-bit value; a GSCAN Capabilities attribute. */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_NUM_EPNO_NETS_BY_SSID |
| = 43, |
| /* Unsigned 32-bit value; a GSCAN Capabilities attribute. */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_NUM_ALLOWLISTED_SSID |
| = 44, |
| |
| QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_BUCKETS_SCANNED = 45, |
| |
| /* Unsigned 32-bit value; a GSCAN Capabilities attribute. |
| * This is used to limit the maximum number of BSSIDs while sending |
| * the vendor command QCA_NL80211_VENDOR_SUBCMD_ROAM with subcmd |
| * QCA_WLAN_VENDOR_ROAMING_SUBCMD_SET_DENYLIST_BSSID and attribute |
| * QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_NUM_BSSID. |
| */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_MAX_NUM_DENYLISTED_BSSID = 46, |
| |
| /* Attribute used for padding for 64-bit alignment */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_PAD = 47, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_MAX = |
| QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_AFTER_LAST - 1, |
| }; |
| |
| /* old names for API compatibility */ |
| #define QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_NUM_WHITELISTED_SSID \ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_NUM_ALLOWLISTED_SSID |
| #define QCA_WLAN_VENDOR_ATTR_GSCAN_MAX_NUM_BLACKLISTED_BSSID \ |
| QCA_WLAN_VENDOR_ATTR_GSCAN_MAX_NUM_DENYLISTED_BSSID |
| |
| enum qca_wlan_vendor_attr_pno_config_params { |
| QCA_WLAN_VENDOR_ATTR_PNO_INVALID = 0, |
| /* Attributes for data used by |
| * QCA_NL80211_VENDOR_SUBCMD_PNO_SET_PASSPOINT_LIST sub command. |
| */ |
| /* Unsigned 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_LIST_PARAM_NUM = 1, |
| /* Array of nested QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_* |
| * attributes. Array size = |
| * QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_LIST_PARAM_NUM. |
| */ |
| QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_LIST_PARAM_NETWORK_ARRAY = 2, |
| |
| /* Unsigned 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_ID = 3, |
| /* An array of 256 x unsigned 8-bit value; NULL terminated UTF-8 encoded |
| * realm, 0 if unspecified. |
| */ |
| QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_REALM = 4, |
| /* An array of 16 x unsigned 32-bit value; roaming consortium ids to |
| * match, 0 if unspecified. |
| */ |
| QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_ROAM_CNSRTM_ID = 5, |
| /* An array of 6 x unsigned 8-bit value; MCC/MNC combination, 0s if |
| * unspecified. |
| */ |
| QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_ROAM_PLMN = 6, |
| |
| /* Attributes for data used by |
| * QCA_NL80211_VENDOR_SUBCMD_PNO_SET_LIST sub command. |
| */ |
| /* Unsigned 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_NUM_NETWORKS = 7, |
| /* Array of nested |
| * QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_* |
| * attributes. Array size = |
| * QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_NUM_NETWORKS. |
| */ |
| QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORKS_LIST = 8, |
| /* An array of 33 x unsigned 8-bit value; NULL terminated SSID */ |
| QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_SSID = 9, |
| /* Signed 8-bit value; threshold for considering this SSID as found, |
| * required granularity for this threshold is 4 dBm to 8 dBm. |
| */ |
| QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_RSSI_THRESHOLD |
| = 10, |
| /* Unsigned 8-bit value; WIFI_PNO_FLAG_XXX */ |
| QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_FLAGS = 11, |
| /* Unsigned 8-bit value; auth bit field for matching WPA IE */ |
| QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_AUTH_BIT = 12, |
| /* Unsigned 8-bit to indicate ePNO type; |
| * It takes values from qca_wlan_epno_type |
| */ |
| QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_TYPE = 13, |
| |
| /* Nested attribute to send the channel list */ |
| QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_CHANNEL_LIST = 14, |
| |
| /* Unsigned 32-bit value; indicates the interval between PNO scan |
| * cycles in msec. |
| */ |
| QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_SCAN_INTERVAL = 15, |
| QCA_WLAN_VENDOR_ATTR_EPNO_MIN5GHZ_RSSI = 16, |
| QCA_WLAN_VENDOR_ATTR_EPNO_MIN24GHZ_RSSI = 17, |
| QCA_WLAN_VENDOR_ATTR_EPNO_INITIAL_SCORE_MAX = 18, |
| QCA_WLAN_VENDOR_ATTR_EPNO_CURRENT_CONNECTION_BONUS = 19, |
| QCA_WLAN_VENDOR_ATTR_EPNO_SAME_NETWORK_BONUS = 20, |
| QCA_WLAN_VENDOR_ATTR_EPNO_SECURE_BONUS = 21, |
| QCA_WLAN_VENDOR_ATTR_EPNO_BAND5GHZ_BONUS = 22, |
| /* Unsigned 32-bit value, representing the PNO Request ID */ |
| QCA_WLAN_VENDOR_ATTR_PNO_CONFIG_REQUEST_ID = 23, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_PNO_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_PNO_MAX = |
| QCA_WLAN_VENDOR_ATTR_PNO_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * qca_wlan_vendor_acs_select_reason: This represents the different reasons why |
| * the ACS has to be triggered. These values are used by |
| * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_REASON and |
| * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_REASON |
| */ |
| enum qca_wlan_vendor_acs_select_reason { |
| /* Represents the reason that the ACS triggered during the AP start */ |
| QCA_WLAN_VENDOR_ACS_SELECT_REASON_INIT, |
| /* Represents the reason that DFS found with the current channel */ |
| QCA_WLAN_VENDOR_ACS_SELECT_REASON_DFS, |
| /* Represents the reason that LTE co-exist in the current band. */ |
| QCA_WLAN_VENDOR_ACS_SELECT_REASON_LTE_COEX, |
| /* Represents the reason that generic, uncategorized interference has |
| * been found in the current channel. |
| */ |
| QCA_WLAN_VENDOR_ACS_SELECT_REASON_GENERIC_INTERFERENCE, |
| /* Represents the reason that excessive 802.11 interference has been |
| * found in the current channel. |
| */ |
| QCA_WLAN_VENDOR_ACS_SELECT_REASON_80211_INTERFERENCE, |
| /* Represents the reason that generic Continuous Wave (CW) interference |
| * has been found in the current channel. |
| */ |
| QCA_WLAN_VENDOR_ACS_SELECT_REASON_CW_INTERFERENCE, |
| /* Represents the reason that Microwave Oven (MWO) interference has been |
| * found in the current channel. |
| */ |
| QCA_WLAN_VENDOR_ACS_SELECT_REASON_MWO_INTERFERENCE, |
| /* Represents the reason that generic Frequency-Hopping Spread Spectrum |
| * (FHSS) interference has been found in the current channel. This may |
| * include 802.11 waveforms. |
| */ |
| QCA_WLAN_VENDOR_ACS_SELECT_REASON_FHSS_INTERFERENCE, |
| /* Represents the reason that non-802.11 generic Frequency-Hopping |
| * Spread Spectrum (FHSS) interference has been found in the current |
| * channel. |
| */ |
| QCA_WLAN_VENDOR_ACS_SELECT_REASON_NON_80211_FHSS_INTERFERENCE, |
| /* Represents the reason that generic Wideband (WB) interference has |
| * been found in the current channel. This may include 802.11 waveforms. |
| */ |
| QCA_WLAN_VENDOR_ACS_SELECT_REASON_WB_INTERFERENCE, |
| /* Represents the reason that non-802.11 generic Wideband (WB) |
| * interference has been found in the current channel. |
| */ |
| QCA_WLAN_VENDOR_ACS_SELECT_REASON_NON_80211_WB_INTERFERENCE, |
| /* Represents the reason that Jammer interference has been found in the |
| * current channel. |
| */ |
| QCA_WLAN_VENDOR_ACS_SELECT_REASON_JAMMER_INTERFERENCE, |
| /* Represents the reason that ACS triggered by AFC */ |
| QCA_WLAN_VENDOR_ACS_SELECT_REASON_AFC_TRIGGER, |
| }; |
| |
| /** |
| * qca_wlan_vendor_attr_external_acs_policy: Attribute values for |
| * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_POLICY to the vendor subcmd |
| * QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS. This represents the |
| * external ACS policies to select the channels w.r.t. the PCL weights. |
| * (QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PCL represents the channels and |
| * their PCL weights.) |
| * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_POLICY_PCL_MANDATORY: Mandatory to |
| * select a channel with non-zero PCL weight. |
| * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_POLICY_PCL_PREFERRED: Prefer a |
| * channel with non-zero PCL weight. |
| * |
| */ |
| enum qca_wlan_vendor_attr_external_acs_policy { |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_POLICY_PCL_PREFERRED, |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_POLICY_PCL_MANDATORY, |
| }; |
| |
| /** |
| * qca_wlan_vendor_channel_prop_flags: This represent the flags for a channel. |
| * This is used by QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS. |
| */ |
| enum qca_wlan_vendor_channel_prop_flags { |
| /* Bits 0, 1, 2, and 3 are reserved */ |
| |
| /* Turbo channel */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_TURBO = 1 << 4, |
| /* CCK channel */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_CCK = 1 << 5, |
| /* OFDM channel */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_OFDM = 1 << 6, |
| /* 2.4 GHz spectrum channel. */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_2GHZ = 1 << 7, |
| /* 5 GHz spectrum channel */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_5GHZ = 1 << 8, |
| /* Only passive scan allowed */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_PASSIVE = 1 << 9, |
| /* Dynamic CCK-OFDM channel */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_DYN = 1 << 10, |
| /* GFSK channel (FHSS PHY) */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_GFSK = 1 << 11, |
| /* Radar found on channel */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_RADAR = 1 << 12, |
| /* 11a static turbo channel only */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_STURBO = 1 << 13, |
| /* Half rate channel */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HALF = 1 << 14, |
| /* Quarter rate channel */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_QUARTER = 1 << 15, |
| /* HT 20 channel */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT20 = 1 << 16, |
| /* HT 40 with extension channel above */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40PLUS = 1 << 17, |
| /* HT 40 with extension channel below */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40MINUS = 1 << 18, |
| /* HT 40 intolerant */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40INTOL = 1 << 19, |
| /* VHT 20 channel */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT20 = 1 << 20, |
| /* VHT 40 with extension channel above */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT40PLUS = 1 << 21, |
| /* VHT 40 with extension channel below */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT40MINUS = 1 << 22, |
| /* VHT 80 channel */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT80 = 1 << 23, |
| /* HT 40 intolerant mark bit for ACS use */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40INTOLMARK = 1 << 24, |
| /* Channel temporarily blocked due to noise */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_BLOCKED = 1 << 25, |
| /* VHT 160 channel */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT160 = 1 << 26, |
| /* VHT 80+80 channel */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT80_80 = 1 << 27, |
| /* HE 20 channel */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE20 = 1 << 28, |
| /* HE 40 with extension channel above */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40PLUS = 1 << 29, |
| /* HE 40 with extension channel below */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40MINUS = 1 << 30, |
| /* HE 40 intolerant */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40INTOL = 1U << 31, |
| }; |
| |
| /** |
| * qca_wlan_vendor_channel_prop_flags_2: This represents the flags for a |
| * channel, and is a continuation of qca_wlan_vendor_channel_prop_flags. This is |
| * used by QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS_2. |
| */ |
| enum qca_wlan_vendor_channel_prop_flags_2 { |
| /* HE 40 intolerant mark bit for ACS use */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40INTOLMARK = 1 << 0, |
| /* HE 80 channel */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE80 = 1 << 1, |
| /* HE 160 channel */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE160 = 1 << 2, |
| /* HE 80+80 channel */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE80_80 = 1 << 3, |
| }; |
| |
| /** |
| * qca_wlan_vendor_channel_prop_flags_ext: This represent the extended flags for |
| * each channel. This is used by |
| * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAG_EXT. |
| */ |
| enum qca_wlan_vendor_channel_prop_flags_ext { |
| /* Radar found on channel */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_RADAR_FOUND = 1 << 0, |
| /* DFS required on channel */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DFS = 1 << 1, |
| /* DFS required on channel for 2nd band of 80+80 */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DFS_CFREQ2 = 1 << 2, |
| /* If channel has been checked for DFS */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DFS_CLEAR = 1 << 3, |
| /* Excluded in 802.11d */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_11D_EXCLUDED = 1 << 4, |
| /* Channel Switch Announcement received on this channel */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_CSA_RECEIVED = 1 << 5, |
| /* Ad-hoc is not allowed */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DISALLOW_ADHOC = 1 << 6, |
| /* Station only channel */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DISALLOW_HOSTAP = 1 << 7, |
| /* DFS radar history for client device (STA mode) */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_HISTORY_RADAR = 1 << 8, |
| /* DFS CAC valid for client device (STA mode) */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_CAC_VALID = 1 << 9, |
| }; |
| |
| /** |
| * qca_wlan_vendor_external_acs_event_chan_info_attr: Represents per channel |
| * information. These attributes are sent as part of |
| * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_CHAN_INFO. Each set of the following |
| * attributes correspond to a single channel. |
| */ |
| enum qca_wlan_vendor_external_acs_event_chan_info_attr { |
| QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_INVALID = 0, |
| |
| /* A bitmask (u32) with flags specified in |
| * enum qca_wlan_vendor_channel_prop_flags. |
| */ |
| QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS = 1, |
| /* A bitmask (u32) with flags specified in |
| * enum qca_wlan_vendor_channel_prop_flags_ext. |
| */ |
| QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAG_EXT = 2, |
| /* frequency in MHz (u32) */ |
| QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ = 3, |
| /* maximum regulatory transmission power (u32) */ |
| QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MAX_REG_POWER = 4, |
| /* maximum transmission power (u32) */ |
| QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MAX_POWER = 5, |
| /* minimum transmission power (u32) */ |
| QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MIN_POWER = 6, |
| /* regulatory class id (u8) */ |
| QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_REG_CLASS_ID = 7, |
| /* maximum antenna gain in (u8) */ |
| QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_ANTENNA_GAIN = 8, |
| /* VHT segment 0 (u8) */ |
| QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_VHT_SEG_0 = 9, |
| /* VHT segment 1 (u8) */ |
| QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_VHT_SEG_1 = 10, |
| /* A bitmask (u32) with flags specified in |
| * enum qca_wlan_vendor_channel_prop_flags_2. |
| */ |
| QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS_2 = 11, |
| |
| /* |
| * Segment 0 in MHz (u32). |
| * |
| * For 20/40/80 MHz bandwidth, this indicates the channel center |
| * frequency index for the 20/40/80 MHz operating channel. |
| * For 160 MHz bandwidth, this indicates the channel center |
| * frequency of the primary 80 MHz channel. |
| * For 320 MHz bandwidth, indicates the channel center frequency |
| * of the primary 160 MHz channel. |
| * |
| * To maintain backward compatibility, |
| * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_VHT_SEG_0 |
| * is also maintained. |
| */ |
| QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_SEG_0 = 12, |
| /* Legacy alias for the Segment 0 attribute. |
| * |
| * VHT segment 0 in MHz (u32) and the attribute is mandatory. |
| * Note: Event QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS includes |
| * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_VHT_SEG_0 |
| * along with |
| * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_VHT_SEG_0. |
| * |
| * If both the driver and user-space application supports the 6 GHz |
| * band, QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_VHT_SEG_0 |
| * is deprecated and |
| * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_VHT_SEG_0 |
| * should be used. |
| * |
| * To maintain backward compatibility, |
| * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_VHT_SEG_0 |
| * is still used if either of the driver or user space application |
| * doesn't support the 6 GHz band. |
| */ |
| QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_VHT_SEG_0 = |
| QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_SEG_0, |
| |
| /* |
| * Segment 1 in MHz (u32). |
| * |
| * For 20/40/80 MHz bandwidth, this is set to 0. |
| * For 160 MHz bandwidth, indicates the channel center frequency of the |
| * 160 MHz channel. |
| * For 320 MHz bandwidth, indicates the channel center frequency of the |
| * 320 MHz channel. |
| * |
| * To maintain backward compatibility, |
| * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_VHT_SEG_1 |
| * is also maintained. |
| */ |
| QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_SEG_1 = 13, |
| /* Legacy alias for the Segment 1 attribute. |
| * |
| * VHT segment 1 in MHz (u32) and the attribute is mandatory. |
| * Note: Event QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS includes |
| * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_VHT_SEG_1 |
| * along with |
| * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_VHT_SEG_1. |
| * |
| * If both the driver and user-space application supports the 6 GHz |
| * band, QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_VHT_SEG_1 |
| * is deprecated and |
| * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_VHT_SEG_1 |
| * should be considered. |
| * |
| * To maintain backward compatibility, |
| * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_VHT_SEG_1 |
| * is still used if either of the driver or user space application |
| * doesn't support the 6 GHz band. |
| */ |
| QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_VHT_SEG_1 = |
| QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_SEG_1, |
| |
| /* |
| * 16-bit attribute of bits indicating the AP power modes supported by |
| * the channel (u16). |
| * Note: Currently, only 3 bits are used in the attribute and each bit |
| * corresponds to the power mode mentioned in enum |
| * qca_wlan_vendor_external_acs_chan_power_mode and a given bit is |
| * set if the associated mode is supported. |
| */ |
| QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_SUPP_POWER_MODES |
| = 14, |
| /* Array of nested attributes for each power mode. It takes attr as |
| * defined in enum |
| * qca_wlan_vendor_external_acs_event_chan_power_info_attr. |
| */ |
| QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_POWER_INFO_ATTR = 15, |
| /* |
| * This indicates the overlapping 320 MHz center frequency in MHz |
| * (u32), if the given primary channel supports more than one |
| * 320 MHz channel bonding. |
| * |
| * Example: |
| * For 6 GHz, channel frequency 6115 MHz (channel number 33) segment 0 |
| * center frequency (primary 160 MHz) is 6185 MHz and there can be two |
| * possible segment 2 frequencies for this (320 MHz center |
| * frequencies): |
| * |
| * 1) Center frequency 6105 MHz (channel 31): 320 MHz channel bonding |
| * from frequency 5945 MHz - 6265 MHz |
| * 2) Center frequency 6265 MHz (channel 63): 320 MHz channel bonding |
| * from frequency 6105 MHz - 6425 MHz |
| * |
| * In this case, |
| * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_SEG_0 will |
| * return 6185 MHz. |
| * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_SEG_1 will |
| * return 6105 MHz. |
| * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_OVERLAP_SEG_1 |
| * will return 6265 MHz. |
| */ |
| QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_OVERLAP_SEG_1 |
| = 16, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_LAST, |
| QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MAX = |
| QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_LAST - 1, |
| }; |
| |
| /** |
| * qca_wlan_vendor_external_acs_chan_power_mode - Specifies the valid |
| * values that the vendor external ACS channel power attribute |
| * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_POWER_INFO_ATTR_POWER_MODE can |
| * take. |
| * @QCA_WLAN_VENDOR_EXTERNAL_ACS_CHAN_LOW_POWER: Low power/Indoor mode |
| * @QCA_WLAN_VENDOR_EXTERNAL_ACS_CHAN_STANDARD_POWER: Standard power mode |
| * @QCA_WLAN_VENDOR_EXTERNAL_ACS_CHAN_VERY_LOW_POWER: Very low power mode |
| */ |
| enum qca_wlan_vendor_external_acs_chan_power_level { |
| QCA_WLAN_VENDOR_EXTERNAL_ACS_CHAN_LOW_POWER = 0, |
| QCA_WLAN_VENDOR_EXTERNAL_ACS_CHAN_STANDARD_POWER = 1, |
| QCA_WLAN_VENDOR_EXTERNAL_ACS_CHAN_VERY_LOW_POWER = 2, |
| }; |
| |
| /** |
| * qca_wlan_vendor_external_acs_event_chan_power_info_attr: Represents nested |
| * attributes for power mode type and power values corresponding to that. |
| * These attributes are sent as part of |
| * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_POWER_INFO_ATTR. |
| */ |
| enum qca_wlan_vendor_external_acs_event_chan_power_info_attr { |
| QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_POWER_INFO_ATTR_INVALID = 0, |
| /* |
| * Power mode (u8) takes the values defined in enum |
| * qca_wlan_vendor_external_acs_chan_power_mode |
| */ |
| QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_POWER_INFO_ATTR_POWER_MODE |
| = 1, |
| /* |
| * Indicates if power value is a PSD/EIRP value (flag). If flag is |
| * present, it indicates a PSD value. |
| */ |
| QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_POWER_INFO_ATTR_PSD_FLAG = 2, |
| /* |
| * Power value (u32) PSD/EIRP as indicated by |
| * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_POWER_INFO_ATTR_PSD_FLAG, |
| * for power mode corresponding to the |
| * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_POWER_INFO_ATTR_POWER_MODE. |
| * Units for PSD - dBm/MHz |
| * Units for EIRP - dBm |
| */ |
| QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_POWER_INFO_ATTR_POWER_VALUE |
| = 3, |
| /* keep last */ |
| QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_POWER_INFO_ATTR_LAST, |
| QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_POWER_INFO_ATTR_MAX = |
| QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_POWER_INFO_ATTR_LAST - 1, |
| }; |
| |
| /** |
| * qca_wlan_vendor_attr_pcl: Represents attributes for |
| * preferred channel list (PCL). These attributes are sent as part of |
| * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PCL and |
| * QCA_NL80211_VENDOR_SUBCMD_GET_PREFERRED_FREQ_LIST. |
| */ |
| enum qca_wlan_vendor_attr_pcl { |
| QCA_WLAN_VENDOR_ATTR_PCL_INVALID = 0, |
| |
| /* Channel number (u8) */ |
| QCA_WLAN_VENDOR_ATTR_PCL_CHANNEL = 1, |
| /* Channel weightage (u8) */ |
| QCA_WLAN_VENDOR_ATTR_PCL_WEIGHT = 2, |
| /* Channel frequency (u32) in MHz */ |
| QCA_WLAN_VENDOR_ATTR_PCL_FREQ = 3, |
| /* Channel flags (u32) |
| * bit 0 set: channel to be used for GO role, |
| * bit 1 set: channel to be used on CLI role, |
| * bit 2 set: channel must be considered for operating channel |
| * selection & peer chosen operating channel should be |
| * one of the channels with this flag set, |
| * bit 3 set: channel should be excluded in GO negotiation |
| */ |
| QCA_WLAN_VENDOR_ATTR_PCL_FLAG = 4, |
| |
| /* Keep last */ |
| QCA_WLAN_VENDOR_ATTR_PCL_LAST, |
| QCA_WLAN_VENDOR_ATTR_PCL_MAX = QCA_WLAN_VENDOR_ATTR_PCL_LAST - 1 |
| }; |
| |
| /** |
| * qca_wlan_vendor_attr_external_acs_event: Attribute to vendor sub-command |
| * QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS. This attribute will be sent by |
| * host driver. |
| */ |
| enum qca_wlan_vendor_attr_external_acs_event { |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_INVALID = 0, |
| |
| /* This reason (u8) refers to enum qca_wlan_vendor_acs_select_reason. |
| * This helps ACS module to understand why ACS needs to be started. |
| */ |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_REASON = 1, |
| /* Flag attribute to indicate if driver supports spectral scanning */ |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_IS_SPECTRAL_SUPPORTED = 2, |
| /* Flag attribute to indicate if 11ac is offloaded to firmware */ |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_IS_OFFLOAD_ENABLED = 3, |
| /* Flag attribute to indicate if driver provides additional channel |
| * capability as part of scan operation |
| */ |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_ADD_CHAN_STATS_SUPPORT = 4, |
| /* Flag attribute to indicate interface status is UP */ |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_AP_UP = 5, |
| /* Operating mode (u8) of interface. Takes one of enum nl80211_iftype |
| * values. |
| */ |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_SAP_MODE = 6, |
| /* Channel width (u8). It takes one of enum nl80211_chan_width values. |
| * This is the upper bound of channel width. ACS logic should try to get |
| * a channel with the specified width and if not found, look for lower |
| * values. |
| */ |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_CHAN_WIDTH = 7, |
| /* This (u8) will hold values of one of enum nl80211_bands */ |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_BAND = 8, |
| /* PHY/HW mode (u8). Takes one of enum qca_wlan_vendor_acs_hw_mode |
| * values |
| */ |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PHY_MODE = 9, |
| /* Array of (u32) supported frequency list among which ACS should choose |
| * best frequency. |
| */ |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_FREQ_LIST = 10, |
| /* Preferred channel list by the driver which will have array of nested |
| * values as per enum qca_wlan_vendor_attr_pcl attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PCL = 11, |
| /* Array of nested attribute for each channel. It takes attr as defined |
| * in enum qca_wlan_vendor_external_acs_event_chan_info_attr. |
| */ |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_CHAN_INFO = 12, |
| /* External ACS policy such as PCL mandatory, PCL preferred, etc. |
| * It uses values defined in enum |
| * qca_wlan_vendor_attr_external_acs_policy. |
| */ |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_POLICY = 13, |
| /* Reference RF Operating Parameter (RROP) availability information |
| * (u16). It uses values defined in enum |
| * qca_wlan_vendor_attr_rropavail_info. |
| */ |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_RROPAVAIL_INFO = 14, |
| /* Flag attribute to indicate if driver supports 6 GHz AFC trigger |
| * for External ACS |
| */ |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_AFC_CAPABILITY = 15, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_LAST, |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_MAX = |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_external_acs_channels: Attributes to vendor subcmd |
| * QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS. This carries a list of channels |
| * in priority order as decided after ACS operation in userspace. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_REASON: Required (u8). |
| * One of reason code from enum qca_wlan_vendor_acs_select_reason. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LIST: Required |
| * Array of nested values for each channel with following attributes: |
| * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_PRIMARY, |
| * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_SECONDARY, |
| * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG0, |
| * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG1, |
| * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_WIDTH |
| * Note: If both the driver and user-space application supports the 6 GHz band, |
| * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LIST is deprecated and use |
| * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_LIST. |
| * To maintain backward compatibility, |
| * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LIST |
| * is still used if either of the driver or user space application doesn't |
| * support the 6 GHz band. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_PRIMARY: Required (u8). |
| * Primary channel number |
| * Note: If both the driver and user-space application supports the 6 GHz band, |
| * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_PRIMARY is deprecated and use |
| * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_PRIMARY. |
| * To maintain backward compatibility, |
| * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_PRIMARY |
| * is still used if either of the driver or user space application doesn't |
| * support the 6 GHz band. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_SECONDARY: Required (u8). |
| * Secondary channel number, required only for 160 and 80+80 MHz bandwidths. |
| * Note: If both the driver and user-space application supports the 6 GHz band, |
| * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_SECONDARY is deprecated and use |
| * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_SECONDARY. |
| * To maintain backward compatibility, |
| * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_SECONDARY |
| * is still used if either of the driver or user space application |
| * doesn't support the 6 GHz band. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG0: Required (u8). |
| * VHT seg0 channel number |
| * Note: If both the driver and user-space application supports the 6 GHz band, |
| * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG0 is deprecated and use |
| * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_CENTER_SEG0. |
| * To maintain backward compatibility, |
| * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG0 |
| * is still used if either of the driver or user space application |
| * doesn't support the 6 GHz band. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG1: Required (u8). |
| * VHT seg1 channel number |
| * Note: If both the driver and user-space application supports the 6 GHz band, |
| * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG1 is deprecated and use |
| * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_CENTER_SEG1. |
| * To maintain backward compatibility, |
| * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG1 |
| * is still used if either of the driver or user space application |
| * doesn't support the 6 GHz band. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_WIDTH: Required (u8). |
| * Takes one of enum nl80211_chan_width values. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_LIST: Required |
| * Array of nested values for each channel with following attributes: |
| * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_PRIMARY in MHz (u32), |
| * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_SECONDARY in MHz (u32), |
| * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_CENTER_SEG0 in MHz (u32), |
| * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_CENTER_SEG1 in MHz (u32), |
| * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_WIDTH |
| * Note: If user-space application has no support of the 6 GHz band, this |
| * attribute is optional. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_PRIMARY: Required (u32) |
| * Primary channel frequency in MHz |
| * Note: If user-space application has no support of the 6 GHz band, this |
| * attribute is optional. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_SECONDARY: Required (u32) |
| * Secondary channel frequency in MHz used for HT 40 MHz channels. |
| * Note: If user-space application has no support of the 6 GHz band, this |
| * attribute is optional. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_CENTER_SEG0: Required (u32) |
| * VHT seg0 channel frequency in MHz |
| * Note: If user-space application has no support of the 6GHz band, this |
| * attribute is optional. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_CENTER_SEG1: Required (u32) |
| * VHT seg1 channel frequency in MHz |
| * Note: If user-space application has no support of the 6 GHz band, this |
| * attribute is optional. |
| * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_PUNCTURE_BITMAP: Required (u16) |
| * Puncture Bitmap for selected primary channel. Optional if no support |
| * for EHT (IEEE 802.11be). Encoding for this attribute follows the |
| * convention used in the Disabled Subchannel Bitmap field of the EHT Operation |
| * element. |
| */ |
| enum qca_wlan_vendor_attr_external_acs_channels { |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_INVALID = 0, |
| |
| /* One of reason code (u8) from enum qca_wlan_vendor_acs_select_reason |
| */ |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_REASON = 1, |
| |
| /* Array of nested values for each channel with following attributes: |
| * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_BAND, |
| * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_PRIMARY, |
| * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_SECONDARY, |
| * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG0, |
| * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG1, |
| * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_WIDTH |
| */ |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LIST = 2, |
| /* This (u8) will hold values of one of enum nl80211_bands */ |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_BAND = 3, |
| /* Primary channel (u8) */ |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_PRIMARY = 4, |
| /* Secondary channel (u8) used for HT 40 MHz channels */ |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_SECONDARY = 5, |
| /* VHT seg0 channel (u8) */ |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG0 = 6, |
| /* VHT seg1 channel (u8) */ |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG1 = 7, |
| /* Channel width (u8). Takes one of enum nl80211_chan_width values. */ |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_WIDTH = 8, |
| |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_LIST = 9, |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_PRIMARY = 10, |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_SECONDARY = 11, |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_CENTER_SEG0 = 12, |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_CENTER_SEG1 = 13, |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_PUNCTURE_BITMAP = 14, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LAST, |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_MAX = |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LAST - 1 |
| }; |
| |
| enum qca_chip_power_save_failure_reason { |
| /* Indicates if the reason for the failure is due to a protocol |
| * layer/module. |
| */ |
| QCA_CHIP_POWER_SAVE_FAILURE_REASON_PROTOCOL = 0, |
| /* Indicates if the reason for the failure is due to a hardware issue. |
| */ |
| QCA_CHIP_POWER_SAVE_FAILURE_REASON_HARDWARE = 1, |
| }; |
| |
| /** |
| * qca_attr_chip_power_save_failure: Attributes to vendor subcmd |
| * QCA_NL80211_VENDOR_SUBCMD_CHIP_PWRSAVE_FAILURE. This carries the requisite |
| * information leading to the power save failure. |
| */ |
| enum qca_attr_chip_power_save_failure { |
| QCA_ATTR_CHIP_POWER_SAVE_FAILURE_INVALID = 0, |
| /* Reason to cause the power save failure. |
| * These reasons are represented by |
| * enum qca_chip_power_save_failure_reason. |
| */ |
| QCA_ATTR_CHIP_POWER_SAVE_FAILURE_REASON = 1, |
| |
| /* keep last */ |
| QCA_ATTR_CHIP_POWER_SAVE_FAILURE_LAST, |
| QCA_ATTR_CHIP_POWER_SAVE_FAILURE_MAX = |
| QCA_ATTR_CHIP_POWER_SAVE_FAILURE_LAST - 1, |
| }; |
| |
| /** |
| * qca_wlan_vendor_nud_stats_data_pkt_flags: Flag representing the various |
| * data types for which the stats have to get collected. |
| */ |
| enum qca_wlan_vendor_nud_stats_data_pkt_flags { |
| QCA_WLAN_VENDOR_NUD_STATS_DATA_ARP = 1 << 0, |
| QCA_WLAN_VENDOR_NUD_STATS_DATA_DNS = 1 << 1, |
| QCA_WLAN_VENDOR_NUD_STATS_DATA_TCP_HANDSHAKE = 1 << 2, |
| QCA_WLAN_VENDOR_NUD_STATS_DATA_ICMPV4 = 1 << 3, |
| QCA_WLAN_VENDOR_NUD_STATS_DATA_ICMPV6 = 1 << 4, |
| /* Used by QCA_ATTR_NUD_STATS_PKT_TYPE only in nud stats get |
| * to represent the stats of respective data type. |
| */ |
| QCA_WLAN_VENDOR_NUD_STATS_DATA_TCP_SYN = 1 << 5, |
| QCA_WLAN_VENDOR_NUD_STATS_DATA_TCP_SYN_ACK = 1 << 6, |
| QCA_WLAN_VENDOR_NUD_STATS_DATA_TCP_ACK = 1 << 7, |
| }; |
| |
| enum qca_wlan_vendor_nud_stats_set_data_pkt_info { |
| QCA_ATTR_NUD_STATS_DATA_PKT_INFO_INVALID = 0, |
| /* Represents the data packet type to be monitored (u32). |
| * Host driver tracks the stats corresponding to each data frame |
| * represented by these flags. |
| * These data packets are represented by |
| * enum qca_wlan_vendor_nud_stats_data_pkt_flags |
| */ |
| QCA_ATTR_NUD_STATS_DATA_PKT_INFO_TYPE = 1, |
| /* Name corresponding to the DNS frame for which the respective DNS |
| * stats have to get monitored (string). Max string length 255. |
| */ |
| QCA_ATTR_NUD_STATS_DATA_PKT_INFO_DNS_DOMAIN_NAME = 2, |
| /* source port on which the respective proto stats have to get |
| * collected (u32). |
| */ |
| QCA_ATTR_NUD_STATS_DATA_PKT_INFO_SRC_PORT = 3, |
| /* destination port on which the respective proto stats have to get |
| * collected (u32). |
| */ |
| QCA_ATTR_NUD_STATS_DATA_PKT_INFO_DEST_PORT = 4, |
| /* IPv4 address for which the destined data packets have to be |
| * monitored. (in network byte order), u32. |
| */ |
| QCA_ATTR_NUD_STATS_DATA_PKT_INFO_DEST_IPV4 = 5, |
| /* IPv6 address for which the destined data packets have to be |
| * monitored. (in network byte order), 16 bytes array. |
| */ |
| QCA_ATTR_NUD_STATS_DATA_PKT_INFO_DEST_IPV6 = 6, |
| |
| QCA_ATTR_NUD_STATS_DATA_PKT_INFO_LAST, |
| QCA_ATTR_NUD_STATS_DATA_PKT_INFO_MAX = |
| QCA_ATTR_NUD_STATS_DATA_PKT_INFO_LAST - 1, |
| }; |
| |
| /** |
| * qca_wlan_vendor_attr_nud_stats_set: Attributes to vendor subcmd |
| * QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_SET. This carries the requisite |
| * information to start/stop the NUD statistics collection. |
| */ |
| enum qca_attr_nud_stats_set { |
| QCA_ATTR_NUD_STATS_SET_INVALID = 0, |
| |
| /* Flag to start/stop the NUD statistics collection. |
| * Start - If included, Stop - If not included |
| */ |
| QCA_ATTR_NUD_STATS_SET_START = 1, |
| /* IPv4 address of the default gateway (in network byte order), u32 */ |
| QCA_ATTR_NUD_STATS_GW_IPV4 = 2, |
| /* Represents the list of data packet types to be monitored. |
| * Host driver tracks the stats corresponding to each data frame |
| * represented by these flags. |
| * These data packets are represented by |
| * enum qca_wlan_vendor_nud_stats_set_data_pkt_info |
| */ |
| QCA_ATTR_NUD_STATS_SET_DATA_PKT_INFO = 3, |
| |
| /* keep last */ |
| QCA_ATTR_NUD_STATS_SET_LAST, |
| QCA_ATTR_NUD_STATS_SET_MAX = |
| QCA_ATTR_NUD_STATS_SET_LAST - 1, |
| }; |
| |
| enum qca_attr_nud_data_stats { |
| QCA_ATTR_NUD_DATA_STATS_INVALID = 0, |
| /* Data packet type for which the stats are collected (u32). |
| * Represented by enum qca_wlan_vendor_nud_stats_data_pkt_flags |
| */ |
| QCA_ATTR_NUD_STATS_PKT_TYPE = 1, |
| /* Name corresponding to the DNS frame for which the respective DNS |
| * stats are monitored (string). Max string length 255. |
| */ |
| QCA_ATTR_NUD_STATS_PKT_DNS_DOMAIN_NAME = 2, |
| /* source port on which the respective proto stats are collected (u32). |
| */ |
| QCA_ATTR_NUD_STATS_PKT_SRC_PORT = 3, |
| /* destination port on which the respective proto stats are collected |
| * (u32). |
| */ |
| QCA_ATTR_NUD_STATS_PKT_DEST_PORT = 4, |
| /* IPv4 address for which the destined data packets have to be |
| * monitored. (in network byte order), u32. |
| */ |
| QCA_ATTR_NUD_STATS_PKT_DEST_IPV4 = 5, |
| /* IPv6 address for which the destined data packets have to be |
| * monitored. (in network byte order), 16 bytes array. |
| */ |
| QCA_ATTR_NUD_STATS_PKT_DEST_IPV6 = 6, |
| /* Data packet Request count received from netdev (u32). */ |
| QCA_ATTR_NUD_STATS_PKT_REQ_COUNT_FROM_NETDEV = 7, |
| /* Data packet Request count sent to lower MAC from upper MAC (u32). */ |
| QCA_ATTR_NUD_STATS_PKT_REQ_COUNT_TO_LOWER_MAC = 8, |
| /* Data packet Request count received by lower MAC from upper MAC |
| * (u32) |
| */ |
| QCA_ATTR_NUD_STATS_PKT_REQ_RX_COUNT_BY_LOWER_MAC = 9, |
| /* Data packet Request count successfully transmitted by the device |
| * (u32) |
| */ |
| QCA_ATTR_NUD_STATS_PKT_REQ_COUNT_TX_SUCCESS = 10, |
| /* Data packet Response count received by lower MAC (u32) */ |
| QCA_ATTR_NUD_STATS_PKT_RSP_RX_COUNT_BY_LOWER_MAC = 11, |
| /* Data packet Response count received by upper MAC (u32) */ |
| QCA_ATTR_NUD_STATS_PKT_RSP_RX_COUNT_BY_UPPER_MAC = 12, |
| /* Data packet Response count delivered to netdev (u32) */ |
| QCA_ATTR_NUD_STATS_PKT_RSP_COUNT_TO_NETDEV = 13, |
| /* Data Packet Response count that are dropped out of order (u32) */ |
| QCA_ATTR_NUD_STATS_PKT_RSP_COUNT_OUT_OF_ORDER_DROP = 14, |
| |
| /* keep last */ |
| QCA_ATTR_NUD_DATA_STATS_LAST, |
| QCA_ATTR_NUD_DATA_STATS_MAX = |
| QCA_ATTR_NUD_DATA_STATS_LAST - 1, |
| }; |
| |
| /** |
| * qca_attr_nud_stats_get: Attributes to vendor subcmd |
| * QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_GET. This carries the requisite |
| * NUD statistics collected when queried. |
| */ |
| enum qca_attr_nud_stats_get { |
| QCA_ATTR_NUD_STATS_GET_INVALID = 0, |
| /* ARP Request count from netdev (u32) */ |
| QCA_ATTR_NUD_STATS_ARP_REQ_COUNT_FROM_NETDEV = 1, |
| /* ARP Request count sent to lower MAC from upper MAC (u32) */ |
| QCA_ATTR_NUD_STATS_ARP_REQ_COUNT_TO_LOWER_MAC = 2, |
| /* ARP Request count received by lower MAC from upper MAC (u32) */ |
| QCA_ATTR_NUD_STATS_ARP_REQ_RX_COUNT_BY_LOWER_MAC = 3, |
| /* ARP Request count successfully transmitted by the device (u32) */ |
| QCA_ATTR_NUD_STATS_ARP_REQ_COUNT_TX_SUCCESS = 4, |
| /* ARP Response count received by lower MAC (u32) */ |
| QCA_ATTR_NUD_STATS_ARP_RSP_RX_COUNT_BY_LOWER_MAC = 5, |
| /* ARP Response count received by upper MAC (u32) */ |
| QCA_ATTR_NUD_STATS_ARP_RSP_RX_COUNT_BY_UPPER_MAC = 6, |
| /* ARP Response count delivered to netdev (u32) */ |
| QCA_ATTR_NUD_STATS_ARP_RSP_COUNT_TO_NETDEV = 7, |
| /* ARP Response count dropped due to out of order reception (u32) */ |
| QCA_ATTR_NUD_STATS_ARP_RSP_COUNT_OUT_OF_ORDER_DROP = 8, |
| /* Flag indicating if the station's link to the AP is active. |
| * Active Link - If included, Inactive link - If not included |
| */ |
| QCA_ATTR_NUD_STATS_AP_LINK_ACTIVE = 9, |
| /* Flag indicating if there is any duplicate address detected (DAD). |
| * Yes - If detected, No - If not detected. |
| */ |
| QCA_ATTR_NUD_STATS_IS_DAD = 10, |
| /* List of Data packet types for which the stats are requested. |
| * This list does not carry ARP stats as they are done by the |
| * above attributes. Represented by enum qca_attr_nud_data_stats. |
| */ |
| QCA_ATTR_NUD_STATS_DATA_PKT_STATS = 11, |
| |
| /* keep last */ |
| QCA_ATTR_NUD_STATS_GET_LAST, |
| QCA_ATTR_NUD_STATS_GET_MAX = |
| QCA_ATTR_NUD_STATS_GET_LAST - 1, |
| }; |
| |
| enum qca_wlan_btm_candidate_status { |
| QCA_STATUS_ACCEPT = 0, |
| QCA_STATUS_REJECT_EXCESSIVE_FRAME_LOSS_EXPECTED = 1, |
| QCA_STATUS_REJECT_EXCESSIVE_DELAY_EXPECTED = 2, |
| QCA_STATUS_REJECT_INSUFFICIENT_QOS_CAPACITY = 3, |
| QCA_STATUS_REJECT_LOW_RSSI = 4, |
| QCA_STATUS_REJECT_HIGH_INTERFERENCE = 5, |
| QCA_STATUS_REJECT_UNKNOWN = 6, |
| }; |
| |
| enum qca_wlan_vendor_attr_btm_candidate_info { |
| QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_INVALID = 0, |
| |
| /* 6-byte MAC address representing the BSSID of transition candidate */ |
| QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_BSSID = 1, |
| /* Unsigned 32-bit value from enum qca_wlan_btm_candidate_status |
| * returned by the driver. It says whether the BSSID provided in |
| * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_BSSID is acceptable by |
| * the driver, if not it specifies the reason for rejection. |
| * Note that the user-space can overwrite the transition reject reason |
| * codes provided by driver based on more information. |
| */ |
| QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_STATUS = 2, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_MAX = |
| QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_AFTER_LAST - 1, |
| }; |
| |
| enum qca_attr_trace_level { |
| QCA_ATTR_TRACE_LEVEL_INVALID = 0, |
| /* |
| * Nested array of the following attributes: |
| * QCA_ATTR_TRACE_LEVEL_MODULE, |
| * QCA_ATTR_TRACE_LEVEL_MASK. |
| */ |
| QCA_ATTR_TRACE_LEVEL_PARAM = 1, |
| /* |
| * Specific QCA host driver module. Please refer to the QCA host |
| * driver implementation to get the specific module ID. |
| */ |
| QCA_ATTR_TRACE_LEVEL_MODULE = 2, |
| /* Different trace level masks represented in the QCA host driver. */ |
| QCA_ATTR_TRACE_LEVEL_MASK = 3, |
| |
| /* keep last */ |
| QCA_ATTR_TRACE_LEVEL_AFTER_LAST, |
| QCA_ATTR_TRACE_LEVEL_MAX = |
| QCA_ATTR_TRACE_LEVEL_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_get_he_capabilities - IEEE 802.11ax HE capabilities |
| */ |
| enum qca_wlan_vendor_attr_get_he_capabilities { |
| QCA_WLAN_VENDOR_ATTR_HE_CAPABILITIES_INVALID = 0, |
| /* Whether HE capabilities is supported |
| * (u8 attribute: 0 = not supported, 1 = supported) |
| */ |
| QCA_WLAN_VENDOR_ATTR_HE_SUPPORTED = 1, |
| /* HE PHY capabilities, array of 3 u32 values */ |
| QCA_WLAN_VENDOR_ATTR_PHY_CAPAB = 2, |
| /* HE MAC capabilities (u32 attribute) */ |
| QCA_WLAN_VENDOR_ATTR_MAC_CAPAB = 3, |
| /* HE MCS map (u32 attribute) */ |
| QCA_WLAN_VENDOR_ATTR_HE_MCS = 4, |
| /* Number of SS (u32 attribute) */ |
| QCA_WLAN_VENDOR_ATTR_NUM_SS = 5, |
| /* RU count (u32 attribute) */ |
| QCA_WLAN_VENDOR_ATTR_RU_IDX_MASK = 6, |
| /* PPE threshold data, array of 8 u32 values */ |
| QCA_WLAN_VENDOR_ATTR_PPE_THRESHOLD = 7, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_HE_CAPABILITIES_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_HE_CAPABILITIES_MAX = |
| QCA_WLAN_VENDOR_ATTR_HE_CAPABILITIES_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_spectral_scan - Spectral scan config parameters |
| */ |
| enum qca_wlan_vendor_attr_spectral_scan { |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_INVALID = 0, |
| /* Number of times the chip enters spectral scan mode before |
| * deactivating spectral scans. When set to 0, chip will enter spectral |
| * scan mode continuously. u32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_SCAN_COUNT = 1, |
| /* Spectral scan period. Period increment resolution is 256*Tclk, |
| * where Tclk = 1/44 MHz (Gmode), 1/40 MHz (Amode). u32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_SCAN_PERIOD = 2, |
| /* Spectral scan priority. u32 attribute. */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_PRIORITY = 3, |
| /* Number of FFT data points to compute. u32 attribute. */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_FFT_SIZE = 4, |
| /* Enable targeted gain change before starting the spectral scan FFT. |
| * u32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_GC_ENA = 5, |
| /* Restart a queued spectral scan. u32 attribute. */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RESTART_ENA = 6, |
| /* Noise floor reference number for the calculation of bin power. |
| * u32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_NOISE_FLOOR_REF = 7, |
| /* Disallow spectral scan triggers after TX/RX packets by setting |
| * this delay value to roughly SIFS time period or greater. |
| * u32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_INIT_DELAY = 8, |
| /* Number of strong bins (inclusive) per sub-channel, below |
| * which a signal is declared a narrow band tone. u32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_NB_TONE_THR = 9, |
| /* Specify the threshold over which a bin is declared strong (for |
| * scan bandwidth analysis). u32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_STR_BIN_THR = 10, |
| /* Spectral scan report mode. u32 attribute. */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_WB_RPT_MODE = 11, |
| /* RSSI report mode, if the ADC RSSI is below |
| * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RSSI_THR, |
| * then FFTs will not trigger, but timestamps and summaries get |
| * reported. u32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RSSI_RPT_MODE = 12, |
| /* ADC RSSI must be greater than or equal to this threshold (signed dB) |
| * to ensure spectral scan reporting with normal error code. |
| * u32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RSSI_THR = 13, |
| /* Format of frequency bin magnitude for spectral scan triggered FFTs: |
| * 0: linear magnitude, 1: log magnitude (20*log10(lin_mag)). |
| * u32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_PWR_FORMAT = 14, |
| /* Format of FFT report to software for spectral scan triggered FFTs. |
| * 0: No FFT report (only spectral scan summary report) |
| * 1: 2-dword summary of metrics for each completed FFT + spectral scan |
| * report |
| * 2: 2-dword summary of metrics for each completed FFT + 1x-oversampled |
| * bins (in-band) per FFT + spectral scan summary report |
| * 3: 2-dword summary of metrics for each completed FFT + 2x-oversampled |
| * bins (all) per FFT + spectral scan summary report |
| * u32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RPT_MODE = 15, |
| /* Number of LSBs to shift out in order to scale the FFT bins. |
| * u32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_BIN_SCALE = 16, |
| /* Set to 1 (with spectral_scan_pwr_format=1), to report bin magnitudes |
| * in dBm power. u32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_DBM_ADJ = 17, |
| /* Per chain enable mask to select input ADC for search FFT. |
| * u32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_CHN_MASK = 18, |
| /* An unsigned 64-bit integer provided by host driver to identify the |
| * spectral scan request. This attribute is included in the scan |
| * response message for @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START |
| * and used as an attribute in |
| * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_STOP to identify the |
| * specific scan to be stopped. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_COOKIE = 19, |
| /* Skip interval for FFT reports. u32 attribute */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_FFT_PERIOD = 20, |
| /* Set to report only one set of FFT results. |
| * u32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_SHORT_REPORT = 21, |
| /* Debug level for spectral module in driver. |
| * 0 : Verbosity level 0 |
| * 1 : Verbosity level 1 |
| * 2 : Verbosity level 2 |
| * 3 : Matched filterID display |
| * 4 : One time dump of FFT report |
| * u32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_DEBUG_LEVEL = 22, |
| /* Type of spectral scan request. u32 attribute. |
| * It uses values defined in enum |
| * qca_wlan_vendor_attr_spectral_scan_request_type. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE = 23, |
| /* This specifies the frequency span over which spectral |
| * scan would be carried out. Its value depends on the |
| * value of QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_MODE and |
| * the relation is as follows. |
| * QCA_WLAN_VENDOR_SPECTRAL_SCAN_MODE_NORMAL |
| * Not applicable. Spectral scan would happen in the |
| * operating span. |
| * QCA_WLAN_VENDOR_SPECTRAL_SCAN_MODE_AGILE |
| * Center frequency (in MHz) of the span of interest or |
| * for convenience, center frequency (in MHz) of any channel |
| * in the span of interest. For 80+80 MHz agile spectral scan |
| * request it represents center frequency (in MHz) of the primary |
| * 80 MHz span or for convenience, center frequency (in MHz) of any |
| * channel in the primary 80 MHz span. If agile spectral scan is |
| * initiated without setting a valid frequency it returns the |
| * error code |
| * (QCA_WLAN_VENDOR_SPECTRAL_SCAN_ERR_PARAM_NOT_INITIALIZED). |
| * u32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_FREQUENCY = 24, |
| /* Spectral scan mode. u32 attribute. |
| * It uses values defined in enum qca_wlan_vendor_spectral_scan_mode. |
| * If this attribute is not present, it is assumed to be |
| * normal mode (QCA_WLAN_VENDOR_SPECTRAL_SCAN_MODE_NORMAL). |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_MODE = 25, |
| /* Spectral scan error code. u32 attribute. |
| * It uses values defined in enum |
| * qca_wlan_vendor_spectral_scan_error_code. |
| * This attribute is included only in failure scenarios. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_ERROR_CODE = 26, |
| /* 8-bit unsigned value to enable/disable debug of the |
| * Spectral DMA ring. |
| * 1-enable, 0-disable |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_DMA_RING_DEBUG = 27, |
| /* 8-bit unsigned value to enable/disable debug of the |
| * Spectral DMA buffers. |
| * 1-enable, 0-disable |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_DMA_BUFFER_DEBUG = 28, |
| /* This specifies the frequency span over which spectral scan would be |
| * carried out. Its value depends on the value of |
| * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_MODE and the relation is as |
| * follows. |
| * QCA_WLAN_VENDOR_SPECTRAL_SCAN_MODE_NORMAL |
| * Not applicable. Spectral scan would happen in the operating span. |
| * QCA_WLAN_VENDOR_SPECTRAL_SCAN_MODE_AGILE |
| * This attribute is applicable only for agile spectral scan |
| * requests in 80+80 MHz mode. It represents center frequency (in |
| * MHz) of the secondary 80 MHz span or for convenience, center |
| * frequency (in MHz) of any channel in the secondary 80 MHz span. |
| * u32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_FREQUENCY_2 = 29, |
| /* This attribute specifies the bandwidth to be used for spectral scan |
| * operation. This is an u8 attribute and uses the values in enum |
| * nl80211_chan_width. This is an optional attribute. |
| * If this attribute is not populated, the driver should configure the |
| * spectral scan bandwidth to the maximum value supported by the target |
| * for the current operating bandwidth. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_BANDWIDTH = 30, |
| /* Spectral FFT recapture flag attribute, to enable FFT recapture. |
| * Recapture can only be enabled for scan period greater than 52 us. |
| * If this attribute is enabled, re-triggers will be enabled when AGC |
| * gain changes. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_FFT_RECAPTURE = 31, |
| /* Attribute used for padding for 64-bit alignment */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_PAD = 32, |
| |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_MAX = |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_spectral_diag_stats - Used by the vendor command |
| * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_DIAG_STATS. |
| */ |
| enum qca_wlan_vendor_attr_spectral_diag_stats { |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_INVALID = 0, |
| /* Number of spectral TLV signature mismatches. |
| * u64 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_SIG_MISMATCH = 1, |
| /* Number of spectral phyerror events with insufficient length when |
| * parsing for secondary 80 search FFT report. u64 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_SEC80_SFFT_INSUFFLEN = 2, |
| /* Number of spectral phyerror events without secondary 80 |
| * search FFT report. u64 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_NOSEC80_SFFT = 3, |
| /* Number of spectral phyerror events with vht operation segment 1 id |
| * mismatches in search fft report. u64 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_VHTSEG1ID_MISMATCH = 4, |
| /* Number of spectral phyerror events with vht operation segment 2 id |
| * mismatches in search fft report. u64 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_VHTSEG2ID_MISMATCH = 5, |
| /* Attribute used for padding for 64-bit alignment */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_PAD = 6, |
| |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_MAX = |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_spectral_cap - Used by the vendor command |
| * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO. |
| */ |
| enum qca_wlan_vendor_attr_spectral_cap { |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_INVALID = 0, |
| /* Flag attribute to indicate phydiag capability */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_PHYDIAG = 1, |
| /* Flag attribute to indicate radar detection capability */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_RADAR = 2, |
| /* Flag attribute to indicate spectral capability */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_SPECTRAL = 3, |
| /* Flag attribute to indicate advanced spectral capability */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_ADVANCED_SPECTRAL = 4, |
| /* Spectral hardware generation. u32 attribute. |
| * It uses values defined in enum |
| * qca_wlan_vendor_spectral_scan_cap_hw_gen. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_HW_GEN = 5, |
| /* Spectral bin scaling formula ID. u16 attribute. |
| * It uses values defined in enum |
| * qca_wlan_vendor_spectral_scan_cap_formula_id. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_FORMULA_ID = 6, |
| /* Spectral bin scaling param - low level offset. |
| * s16 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_LOW_LEVEL_OFFSET = 7, |
| /* Spectral bin scaling param - high level offset. |
| * s16 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_HIGH_LEVEL_OFFSET = 8, |
| /* Spectral bin scaling param - RSSI threshold. |
| * s16 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_RSSI_THR = 9, |
| /* Spectral bin scaling param - default AGC max gain. |
| * u8 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_DEFAULT_AGC_MAX_GAIN = 10, |
| /* Flag attribute to indicate agile spectral scan capability |
| * for 20/40/80 MHz modes. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_AGILE_SPECTRAL = 11, |
| /* Flag attribute to indicate agile spectral scan capability |
| * for 160 MHz mode. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_AGILE_SPECTRAL_160 = 12, |
| /* Flag attribute to indicate agile spectral scan capability |
| * for 80+80 MHz mode. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_AGILE_SPECTRAL_80_80 = 13, |
| /* Number of spectral detectors used for scan in 20 MHz. |
| * u32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_NUM_DETECTORS_20_MHZ = 14, |
| /* Number of spectral detectors used for scan in 40 MHz. |
| * u32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_NUM_DETECTORS_40_MHZ = 15, |
| /* Number of spectral detectors used for scan in 80 MHz. |
| * u32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_NUM_DETECTORS_80_MHZ = 16, |
| /* Number of spectral detectors used for scan in 160 MHz. |
| * u32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_NUM_DETECTORS_160_MHZ = 17, |
| /* Number of spectral detectors used for scan in 80+80 MHz. |
| * u32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_NUM_DETECTORS_80P80_MHZ = 18, |
| /* Flag attribute to indicate agile spectral scan capability |
| * for 320 MHz mode. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_AGILE_SPECTRAL_320 = 19, |
| /* Number of spectral detectors used for scan in 320 MHz. |
| * u32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_NUM_DETECTORS_320_MHZ = 20, |
| |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_MAX = |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_spectral_scan_status - used by the vendor command |
| * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_STATUS. |
| */ |
| enum qca_wlan_vendor_attr_spectral_scan_status { |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_INVALID = 0, |
| /* Flag attribute to indicate whether spectral scan is enabled */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_IS_ENABLED = 1, |
| /* Flag attribute to indicate whether spectral scan is in progress*/ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_IS_ACTIVE = 2, |
| /* Spectral scan mode. u32 attribute. |
| * It uses values defined in enum qca_wlan_vendor_spectral_scan_mode. |
| * If this attribute is not present, normal mode |
| * (QCA_WLAN_VENDOR_SPECTRAL_SCAN_MODE_NORMAL is assumed to be |
| * requested. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_MODE = 3, |
| |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_MAX = |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * qca_wlan_vendor_attr_spectral_scan_request_type: Attribute values for |
| * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE to the vendor subcmd |
| * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START. This represents the |
| * spectral scan request types. |
| * @QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_SCAN_AND_CONFIG: Request to |
| * set the spectral parameters and start scan. |
| * @QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_SCAN: Request to |
| * only set the spectral parameters. |
| * @QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_CONFIG: Request to |
| * only start the spectral scan. |
| */ |
| enum qca_wlan_vendor_attr_spectral_scan_request_type { |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_SCAN_AND_CONFIG, |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_SCAN, |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_CONFIG, |
| }; |
| |
| /** |
| * qca_wlan_vendor_spectral_scan_mode: Attribute values for |
| * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_MODE in the vendor subcmd |
| * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START and |
| * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_MODE in the vendor subcmd |
| * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_STATUS. This represents the |
| * spectral scan modes. |
| * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_MODE_NORMAL: Normal spectral scan: |
| * spectral scan in the current operating span. |
| * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_MODE_AGILE: Agile spectral scan: |
| * spectral scan in the configured agile span. |
| */ |
| enum qca_wlan_vendor_spectral_scan_mode { |
| QCA_WLAN_VENDOR_SPECTRAL_SCAN_MODE_NORMAL = 0, |
| QCA_WLAN_VENDOR_SPECTRAL_SCAN_MODE_AGILE = 1, |
| }; |
| |
| /** |
| * qca_wlan_vendor_spectral_scan_error_code: Attribute values for |
| * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_ERROR_CODE in the vendor subcmd |
| * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START. |
| * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_ERR_PARAM_UNSUPPORTED: Changing the value |
| * of a parameter is not supported. |
| * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_ERR_MODE_UNSUPPORTED: Requested spectral scan |
| * mode is not supported. |
| * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_ERR_PARAM_INVALID_VALUE: A parameter |
| * has invalid value. |
| * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_ERR_PARAM_NOT_INITIALIZED: A parameter |
| * is not initialized. |
| */ |
| enum qca_wlan_vendor_spectral_scan_error_code { |
| QCA_WLAN_VENDOR_SPECTRAL_SCAN_ERR_PARAM_UNSUPPORTED = 0, |
| QCA_WLAN_VENDOR_SPECTRAL_SCAN_ERR_MODE_UNSUPPORTED = 1, |
| QCA_WLAN_VENDOR_SPECTRAL_SCAN_ERR_PARAM_INVALID_VALUE = 2, |
| QCA_WLAN_VENDOR_SPECTRAL_SCAN_ERR_PARAM_NOT_INITIALIZED = 3, |
| }; |
| |
| /** |
| * qca_wlan_vendor_spectral_scan_cap_hw_gen: Attribute values for |
| * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_HW_GEN to the vendor subcmd |
| * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO. This represents the |
| * spectral hardware generation. |
| * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_1: generation 1 |
| * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_2: generation 2 |
| * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_3: generation 3 |
| */ |
| enum qca_wlan_vendor_spectral_scan_cap_hw_gen { |
| QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_1 = 0, |
| QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_2 = 1, |
| QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_3 = 2, |
| }; |
| |
| enum qca_wlan_vendor_tos { |
| QCA_WLAN_VENDOR_TOS_BK = 0, |
| QCA_WLAN_VENDOR_TOS_BE = 1, |
| QCA_WLAN_VENDOR_TOS_VI = 2, |
| QCA_WLAN_VENDOR_TOS_VO = 3, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_active_tos - Used by the vendor command |
| * QCA_NL80211_VENDOR_SUBCMD_ACTIVE_TOS. |
| */ |
| enum qca_wlan_vendor_attr_active_tos { |
| QCA_WLAN_VENDOR_ATTR_ACTIVE_TOS_INVALID = 0, |
| /* Type Of Service - Represented by qca_wlan_vendor_tos */ |
| QCA_WLAN_VENDOR_ATTR_ACTIVE_TOS = 1, |
| /* Flag attribute representing the start (attribute included) or stop |
| * (attribute not included) of the respective TOS. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ACTIVE_TOS_START = 2, |
| }; |
| |
| enum qca_wlan_vendor_hang_reason { |
| /* Unspecified reason */ |
| QCA_WLAN_HANG_REASON_UNSPECIFIED = 0, |
| /* No Map for the MAC entry for the received frame */ |
| QCA_WLAN_HANG_RX_HASH_NO_ENTRY_FOUND = 1, |
| /* Peer deletion timeout happened */ |
| QCA_WLAN_HANG_PEER_DELETION_TIMEDOUT = 2, |
| /* Peer unmap timeout */ |
| QCA_WLAN_HANG_PEER_UNMAP_TIMEDOUT = 3, |
| /* Scan request timed out */ |
| QCA_WLAN_HANG_SCAN_REQ_EXPIRED = 4, |
| /* Consecutive Scan attempt failures */ |
| QCA_WLAN_HANG_SCAN_ATTEMPT_FAILURES = 5, |
| /* Unable to get the message buffer */ |
| QCA_WLAN_HANG_GET_MSG_BUFF_FAILURE = 6, |
| /* Current command processing is timedout */ |
| QCA_WLAN_HANG_ACTIVE_LIST_TIMEOUT = 7, |
| /* Timeout for an ACK from FW for suspend request */ |
| QCA_WLAN_HANG_SUSPEND_TIMEOUT = 8, |
| /* Timeout for an ACK from FW for resume request */ |
| QCA_WLAN_HANG_RESUME_TIMEOUT = 9, |
| /* Transmission timeout for consecutive data frames */ |
| QCA_WLAN_HANG_TRANSMISSIONS_TIMEOUT = 10, |
| /* Timeout for the TX completion status of data frame */ |
| QCA_WLAN_HANG_TX_COMPLETE_TIMEOUT = 11, |
| /* DXE failure for TX/RX, DXE resource unavailability */ |
| QCA_WLAN_HANG_DXE_FAILURE = 12, |
| /* WMI pending commands exceed the maximum count */ |
| QCA_WLAN_HANG_WMI_EXCEED_MAX_PENDING_CMDS = 13, |
| /* Timeout for peer STA connection accept command's response from the |
| * FW in AP mode. This command is triggered when a STA (peer) connects |
| * to AP (DUT). |
| */ |
| QCA_WLAN_HANG_AP_STA_CONNECT_REQ_TIMEOUT = 14, |
| /* Timeout for the AP connection accept command's response from the FW |
| * in STA mode. This command is triggered when the STA (DUT) connects |
| * to an AP (peer). |
| */ |
| QCA_WLAN_HANG_STA_AP_CONNECT_REQ_TIMEOUT = 15, |
| /* Timeout waiting for the response to the MAC HW mode change command |
| * sent to FW as a part of MAC mode switch among DBS (Dual Band |
| * Simultaneous), SCC (Single Channel Concurrency), and MCC (Multi |
| * Channel Concurrency) mode. |
| */ |
| QCA_WLAN_HANG_MAC_HW_MODE_CHANGE_TIMEOUT = 16, |
| /* Timeout waiting for the response from FW to configure the MAC HW's |
| * mode. This operation is to configure the single/two MACs in either |
| * SCC/MCC/DBS mode. |
| */ |
| QCA_WLAN_HANG_MAC_HW_MODE_CONFIG_TIMEOUT = 17, |
| /* Timeout waiting for response of VDEV start command from the FW */ |
| QCA_WLAN_HANG_VDEV_START_RESPONSE_TIMED_OUT = 18, |
| /* Timeout waiting for response of VDEV restart command from the FW */ |
| QCA_WLAN_HANG_VDEV_RESTART_RESPONSE_TIMED_OUT = 19, |
| /* Timeout waiting for response of VDEV stop command from the FW */ |
| QCA_WLAN_HANG_VDEV_STOP_RESPONSE_TIMED_OUT = 20, |
| /* Timeout waiting for response of VDEV delete command from the FW */ |
| QCA_WLAN_HANG_VDEV_DELETE_RESPONSE_TIMED_OUT = 21, |
| /* Timeout waiting for response of peer all delete request command to |
| * the FW on a specific VDEV. |
| */ |
| QCA_WLAN_HANG_VDEV_PEER_DELETE_ALL_RESPONSE_TIMED_OUT = 22, |
| /* WMI sequence mismatch between WMI command and Tx completion */ |
| QCA_WLAN_HANG_WMI_BUF_SEQUENCE_MISMATCH = 23, |
| /* Write to Device HAL register failed */ |
| QCA_WLAN_HANG_REG_WRITE_FAILURE = 24, |
| /* No credit left to send the wow_wakeup_from_sleep to firmware */ |
| QCA_WLAN_HANG_SUSPEND_NO_CREDIT = 25, |
| /* Bus failure */ |
| QCA_WLAN_HANG_BUS_FAILURE = 26, |
| /* tasklet/credit latency found */ |
| QCA_WLAN_HANG_TASKLET_CREDIT_LATENCY_DETECT = 27, |
| /* MSDU buffers received in REO error ring, exceeding certain |
| * threshold |
| */ |
| QCA_WLAN_HANG_RX_MSDU_BUF_RCVD_IN_ERR_RING = 28, |
| /* Vdev SM is out of sync and connect req received |
| * when already connected |
| */ |
| QCA_WLAN_HANG_VDEV_SM_OUT_OF_SYNC = 29, |
| /* Stats request timeout */ |
| QCA_WLAN_HANG_STATS_REQ_TIMEOUT = 30, |
| /* Leak in TX descriptor for a packet */ |
| QCA_WLAN_HANG_TX_DESC_LEAK = 31, |
| /* Scheduler watchdog timeout */ |
| QCA_WLAN_HANG_SCHED_TIMEOUT = 32, |
| /* Failed to send self peer deletion cmd to firmware */ |
| QCA_WLAN_HANG_SELF_PEER_DEL_FAIL = 33, |
| /* Received del self sta without del bss */ |
| QCA_WLAN_HANG_DEL_SELF_STA_FAIL = 34, |
| /* Recovery needed when sending flush completion to userspace */ |
| QCA_WLAN_HANG_FLUSH_LOGS = 35, |
| /* Host wakeup because of page fault */ |
| QCA_WLAN_HANG_HOST_WAKEUP_REASON_PAGE_FAULT = 36, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_hang - Used by the vendor command |
| * QCA_NL80211_VENDOR_SUBCMD_HANG. |
| */ |
| enum qca_wlan_vendor_attr_hang { |
| QCA_WLAN_VENDOR_ATTR_HANG_INVALID = 0, |
| /* Reason for the hang - u32 attribute with a value from enum |
| * qca_wlan_vendor_hang_reason. |
| */ |
| QCA_WLAN_VENDOR_ATTR_HANG_REASON = 1, |
| /* The binary blob data associated with the hang reason specified by |
| * QCA_WLAN_VENDOR_ATTR_HANG_REASON. This binary data is expected to |
| * contain the required dump to analyze the reason for the hang. |
| * NLA_BINARY attribute, the max size is 1024 bytes. |
| */ |
| QCA_WLAN_VENDOR_ATTR_HANG_REASON_DATA = 2, |
| |
| QCA_WLAN_VENDOR_ATTR_HANG_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_HANG_MAX = |
| QCA_WLAN_VENDOR_ATTR_HANG_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_flush_pending_policy: Represents values for |
| * the policy to flush pending frames, configured via |
| * %QCA_NL80211_VENDOR_SUBCMD_PEER_FLUSH_PENDING. This enumeration defines the |
| * valid values for %QCA_WLAN_VENDOR_ATTR_FLUSH_PENDING_POLICY. |
| * |
| * @QCA_WLAN_VENDOR_FLUSH_PENDING_POLICY_NONE: This value clears all |
| * the flush policy configured before. This command basically disables the |
| * flush config set by the user. |
| * @QCA_WLAN_VENDOR_FLUSH_PENDING_POLICY_IMMEDIATE: This value configures |
| * the flush policy to be immediate. All pending packets for the peer/TID are |
| * flushed when this command/policy is received. |
| * @QCA_WLAN_VENDOR_FLUSH_PENDING_POLICY_TWT_SP_END: This value configures |
| * the flush policy to the end of TWT SP. All pending packets for the peer/TID |
| * are flushed when the end of TWT SP is reached. |
| */ |
| enum qca_wlan_vendor_flush_pending_policy { |
| QCA_WLAN_VENDOR_FLUSH_PENDING_POLICY_NONE = 0, |
| QCA_WLAN_VENDOR_FLUSH_PENDING_POLICY_IMMEDIATE = 1, |
| QCA_WLAN_VENDOR_FLUSH_PENDING_POLICY_TWT_SP_END = 2, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_flush_pending - Attributes for |
| * flushing pending traffic in firmware. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_PEER_ADDR: Configure peer MAC address. |
| * @QCA_WLAN_VENDOR_ATTR_AC: Configure access category of the pending |
| * packets. It is u8 value with bit 0~3 represent AC_BE, AC_BK, |
| * AC_VI, AC_VO respectively. Set the corresponding bit to 1 to |
| * flush packets with access category. This is optional. See below. |
| * @QCA_WLAN_VENDOR_ATTR_TID_MASK: Configure TID mask of the pending packets. |
| * It is a u32 value with bit 0-7 representing TID 0-7. Set corresponding |
| * bit to 1 to act upon the TID. This is optional. Either this attribute or |
| * %QCA_WLAN_VENDOR_ATTR_AC must be provided. If both are provided, |
| * %QCA_WLAN_VENDOR_ATTR_TID_MASK takes precedence. If neither are provided |
| * it is an error. |
| * @QCA_WLAN_VENDOR_ATTR_FLUSH_PENDING_POLICY: Policy of flushing the pending |
| * packets corresponding to the peer/TID provided. It is a u32 value, |
| * represented by %enum qca_wlan_vendor_flush_pending_policy. This |
| * value is honored only when TID mask is provided. This is not honored when AC |
| * mask is provided. |
| */ |
| enum qca_wlan_vendor_attr_flush_pending { |
| QCA_WLAN_VENDOR_ATTR_FLUSH_PENDING_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_PEER_ADDR = 1, |
| QCA_WLAN_VENDOR_ATTR_AC = 2, |
| QCA_WLAN_VENDOR_ATTR_TID_MASK = 3, |
| QCA_WLAN_VENDOR_ATTR_FLUSH_PENDING_POLICY = 4, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_FLUSH_PENDING_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_FLUSH_PENDING_MAX = |
| QCA_WLAN_VENDOR_ATTR_FLUSH_PENDING_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * qca_wlan_vendor_spectral_scan_cap_formula_id: Attribute values for |
| * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_FORMULA_ID in the vendor subcmd |
| * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO. This represents the |
| * Spectral bin scaling formula ID. |
| * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_NO_SCALING: No scaling |
| * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_AGC_GAIN_RSSI_CORR_BASED: AGC gain |
| * and RSSI threshold based formula. |
| */ |
| enum qca_wlan_vendor_spectral_scan_cap_formula_id { |
| QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_NO_SCALING = 0, |
| QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_AGC_GAIN_RSSI_CORR_BASED = 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_rropavail_info - Specifies whether Representative |
| * RF Operating Parameter (RROP) information is available, and if so, at which |
| * point in the application-driver interaction sequence it can be retrieved by |
| * the application from the driver. This point may vary by architecture and |
| * other factors. This is a u16 value. |
| */ |
| enum qca_wlan_vendor_attr_rropavail_info { |
| /* RROP information is unavailable. */ |
| QCA_WLAN_VENDOR_ATTR_RROPAVAIL_INFO_UNAVAILABLE, |
| /* RROP information is available and the application can retrieve the |
| * information after receiving an QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS |
| * event from the driver. |
| */ |
| QCA_WLAN_VENDOR_ATTR_RROPAVAIL_INFO_EXTERNAL_ACS_START, |
| /* RROP information is available only after a vendor specific scan |
| * (requested using QCA_NL80211_VENDOR_SUBCMD_TRIGGER_SCAN) has |
| * successfully completed. The application can retrieve the information |
| * after receiving the QCA_NL80211_VENDOR_SUBCMD_SCAN_DONE event from |
| * the driver. |
| */ |
| QCA_WLAN_VENDOR_ATTR_RROPAVAIL_INFO_VSCAN_END, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_rrop_info - Specifies vendor specific |
| * Representative RF Operating Parameter (RROP) information. It is sent for the |
| * vendor command QCA_NL80211_VENDOR_SUBCMD_GET_RROP_INFO. This information is |
| * intended for use by external Auto Channel Selection applications. It provides |
| * guidance values for some RF parameters that are used by the system during |
| * operation. These values could vary by channel, band, radio, and so on. |
| */ |
| enum qca_wlan_vendor_attr_rrop_info { |
| QCA_WLAN_VENDOR_ATTR_RROP_INFO_INVALID = 0, |
| |
| /* Representative Tx Power List (RTPL) which has an array of nested |
| * values as per attributes in enum qca_wlan_vendor_attr_rtplinst. |
| */ |
| QCA_WLAN_VENDOR_ATTR_RROP_INFO_RTPL = 1, |
| |
| QCA_WLAN_VENDOR_ATTR_RROP_INFO_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_RROP_INFO_MAX = |
| QCA_WLAN_VENDOR_ATTR_RROP_INFO_AFTER_LAST - 1 |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_rtplinst - Specifies attributes for individual list |
| * entry instances in the Representative Tx Power List (RTPL). It provides |
| * simplified power values intended for helping external Auto channel Selection |
| * applications compare potential Tx power performance between channels, other |
| * operating conditions remaining identical. These values are not necessarily |
| * the actual Tx power values that will be used by the system. They are also not |
| * necessarily the max or average values that will be used. Instead, they are |
| * relative, summarized keys for algorithmic use computed by the driver or |
| * underlying firmware considering a number of vendor specific factors. |
| */ |
| enum qca_wlan_vendor_attr_rtplinst { |
| QCA_WLAN_VENDOR_ATTR_RTPLINST_INVALID = 0, |
| |
| /* Primary channel number (u8). |
| * Note: If both the driver and user space application support the |
| * 6 GHz band, this attribute is deprecated and |
| * QCA_WLAN_VENDOR_ATTR_RTPLINST_PRIMARY_FREQUENCY should be used. To |
| * maintain backward compatibility, |
| * QCA_WLAN_VENDOR_ATTR_RTPLINST_PRIMARY is still used if either the |
| * driver or user space application or both do not support the 6 GHz |
| * band. |
| */ |
| QCA_WLAN_VENDOR_ATTR_RTPLINST_PRIMARY = 1, |
| /* Representative Tx power in dBm (s32) with emphasis on throughput. */ |
| QCA_WLAN_VENDOR_ATTR_RTPLINST_TXPOWER_THROUGHPUT = 2, |
| /* Representative Tx power in dBm (s32) with emphasis on range. */ |
| QCA_WLAN_VENDOR_ATTR_RTPLINST_TXPOWER_RANGE = 3, |
| /* Primary channel center frequency (u32) in MHz */ |
| QCA_WLAN_VENDOR_ATTR_RTPLINST_PRIMARY_FREQUENCY = 4, |
| |
| QCA_WLAN_VENDOR_ATTR_RTPLINST_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_RTPLINST_MAX = |
| QCA_WLAN_VENDOR_ATTR_RTPLINST_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_config_latency_level - Level for |
| * wlan latency module. |
| * |
| * There will be various of Wi-Fi functionality like scan/roaming/adaptive |
| * power saving which would causing data exchange out of service, this |
| * would be a big impact on latency. For latency sensitive applications over |
| * Wi-Fi are intolerant to such operations and thus would configure them |
| * to meet their respective needs. It is well understood by such applications |
| * that altering the default behavior would degrade the Wi-Fi functionality |
| * w.r.t the above pointed WLAN operations. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_NORMAL: |
| * Default WLAN operation level which throughput orientated. |
| * @QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_XR: |
| * Use XR level to benefit XR (extended reality) application to achieve |
| * latency and power by via constraint scan/roaming/adaptive PS. |
| * @QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_LOW: |
| * Use low latency level to benefit application like concurrent |
| * downloading or video streaming via constraint scan/adaptive PS. |
| * @QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_ULTRALOW: |
| * Use ultra low latency level to benefit for gaming/voice |
| * application via constraint scan/roaming/adaptive PS. |
| */ |
| enum qca_wlan_vendor_attr_config_latency_level { |
| QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_NORMAL = 1, |
| QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_XR = 2, |
| /* legacy name */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_MODERATE = |
| QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_XR, |
| QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_LOW = 3, |
| QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_ULTRALOW = 4, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_MAX = |
| QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_wlan_mac - Used by the vendor command |
| * QCA_NL80211_VENDOR_SUBCMD_WLAN_MAC_INFO. |
| */ |
| enum qca_wlan_vendor_attr_mac { |
| QCA_WLAN_VENDOR_ATTR_MAC_INVALID = 0, |
| |
| /* MAC mode info list which has an array of nested values as |
| * per attributes in enum qca_wlan_vendor_attr_mac_mode_info. |
| */ |
| QCA_WLAN_VENDOR_ATTR_MAC_INFO = 1, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_MAC_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_MAC_MAX = |
| QCA_WLAN_VENDOR_ATTR_MAC_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_mac_iface_info - Information of the connected |
| * Wi-Fi netdev interface on a respective MAC. |
| * Used by the attribute QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO. |
| */ |
| enum qca_wlan_vendor_attr_mac_iface_info { |
| QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_INVALID = 0, |
| /* Wi-Fi netdev's interface index (u32) */ |
| QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_IFINDEX = 1, |
| /* Associated frequency in MHz of the connected Wi-Fi interface (u32) */ |
| QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_FREQ = 2, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_MAX = |
| QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_mac_info - Points to MAC the information. |
| * Used by the attribute QCA_WLAN_VENDOR_ATTR_MAC_INFO of the |
| * vendor command QCA_NL80211_VENDOR_SUBCMD_WLAN_MAC_INFO. |
| */ |
| enum qca_wlan_vendor_attr_mac_info { |
| QCA_WLAN_VENDOR_ATTR_MAC_INFO_INVALID = 0, |
| /* Hardware MAC ID associated for the MAC (u32) */ |
| QCA_WLAN_VENDOR_ATTR_MAC_INFO_MAC_ID = 1, |
| /* Band supported by the MAC at a given point. |
| * This is a u32 bitmask of BIT(NL80211_BAND_*) as described in %enum |
| * nl80211_band. |
| */ |
| QCA_WLAN_VENDOR_ATTR_MAC_INFO_BAND = 2, |
| /* Refers to list of WLAN netdev interfaces associated with this MAC. |
| * Represented by enum qca_wlan_vendor_attr_mac_iface_info. |
| */ |
| QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO = 3, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_MAC_INFO_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_MAC_INFO_MAX = |
| QCA_WLAN_VENDOR_ATTR_MAC_INFO_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_get_logger_features - Used by the vendor command |
| * QCA_NL80211_VENDOR_SUBCMD_GET_LOGGER_FEATURE_SET. |
| */ |
| enum qca_wlan_vendor_attr_get_logger_features { |
| QCA_WLAN_VENDOR_ATTR_LOGGER_INVALID = 0, |
| /* Unsigned 32-bit enum value of wifi_logger_supported_features */ |
| QCA_WLAN_VENDOR_ATTR_LOGGER_SUPPORTED = 1, |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_LOGGER_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_LOGGER_MAX = |
| QCA_WLAN_VENDOR_ATTR_LOGGER_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum wifi_logger_supported_features - Values for supported logger features |
| */ |
| enum wifi_logger_supported_features { |
| WIFI_LOGGER_MEMORY_DUMP_FEATURE = (1 << (0)), |
| WIFI_LOGGER_PER_PACKET_TX_RX_STATUS_FEATURE = (1 << (1)), |
| WIFI_LOGGER_CONNECT_EVENT_FEATURE = (1 << (2)), |
| WIFI_LOGGER_POWER_EVENT_FEATURE = (1 << (3)), |
| WIFI_LOGGER_WAKE_LOCK_FEATURE = (1 << (4)), |
| WIFI_LOGGER_VERBOSE_FEATURE = (1 << (5)), |
| WIFI_LOGGER_WATCHDOG_TIMER_FEATURE = (1 << (6)), |
| WIFI_LOGGER_DRIVER_DUMP_FEATURE = (1 << (7)), |
| WIFI_LOGGER_PACKET_FATE_FEATURE = (1 << (8)), |
| }; |
| |
| /** |
| * enum qca_wlan_tdls_caps_features_supported - Values for TDLS get |
| * capabilities features |
| */ |
| enum qca_wlan_tdls_caps_features_supported { |
| WIFI_TDLS_SUPPORT = (1 << (0)), |
| WIFI_TDLS_EXTERNAL_CONTROL_SUPPORT = (1 << (1)), |
| WIFI_TDLS_OFFCHANNEL_SUPPORT = (1 << (2)) |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_tdls_get_capabilities - Used by the vendor command |
| * QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_CAPABILITIES. |
| */ |
| enum qca_wlan_vendor_attr_tdls_get_capabilities { |
| QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_INVALID = 0, |
| /* Indicates the max concurrent sessions */ |
| /* Unsigned 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_MAX_CONC_SESSIONS, |
| /* Indicates the support for features */ |
| /* Unsigned 32-bit bitmap qca_wlan_tdls_caps_features_supported |
| */ |
| QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_FEATURES_SUPPORTED, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_MAX = |
| QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_offloaded_packets_sending_control - Offload packets control |
| * command used as value for the attribute |
| * QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_SENDING_CONTROL. |
| */ |
| enum qca_wlan_offloaded_packets_sending_control { |
| QCA_WLAN_OFFLOADED_PACKETS_SENDING_CONTROL_INVALID = 0, |
| QCA_WLAN_OFFLOADED_PACKETS_SENDING_START, |
| QCA_WLAN_OFFLOADED_PACKETS_SENDING_STOP |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_offloaded_packets - Used by the vendor command |
| * QCA_NL80211_VENDOR_SUBCMD_OFFLOADED_PACKETS. |
| */ |
| enum qca_wlan_vendor_attr_offloaded_packets { |
| QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_INVALID = 0, |
| /* Takes valid value from the enum |
| * qca_wlan_offloaded_packets_sending_control |
| * Unsigned 32-bit value |
| */ |
| QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_SENDING_CONTROL, |
| /* Unsigned 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_REQUEST_ID, |
| /* array of u8 len: Max packet size */ |
| QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_IP_PACKET_DATA, |
| /* 6-byte MAC address used to represent source MAC address */ |
| QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_SRC_MAC_ADDR, |
| /* 6-byte MAC address used to represent destination MAC address */ |
| QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_DST_MAC_ADDR, |
| /* Unsigned 32-bit value, in milli seconds */ |
| QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_PERIOD, |
| /* This optional unsigned 16-bit attribute is used for specifying |
| * ethernet protocol type. If not specified ethertype defaults to IPv4. |
| */ |
| QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_ETHER_PROTO_TYPE, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_MAX = |
| QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_rssi_monitoring_control - RSSI control commands used as values |
| * by the attribute QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CONTROL. |
| */ |
| enum qca_wlan_rssi_monitoring_control { |
| QCA_WLAN_RSSI_MONITORING_CONTROL_INVALID = 0, |
| QCA_WLAN_RSSI_MONITORING_START, |
| QCA_WLAN_RSSI_MONITORING_STOP, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_rssi_monitoring - Used by the vendor command |
| * QCA_NL80211_VENDOR_SUBCMD_MONITOR_RSSI. |
| */ |
| enum qca_wlan_vendor_attr_rssi_monitoring { |
| QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_INVALID = 0, |
| /* Takes valid value from the enum |
| * qca_wlan_rssi_monitoring_control |
| * Unsigned 32-bit value enum qca_wlan_rssi_monitoring_control |
| */ |
| QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CONTROL, |
| /* Unsigned 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_REQUEST_ID, |
| /* Signed 8-bit value in dBm */ |
| QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_MAX_RSSI, |
| /* Signed 8-bit value in dBm */ |
| QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_MIN_RSSI, |
| /* attributes to be used/received in callback */ |
| /* 6-byte MAC address used to represent current BSSID MAC address */ |
| QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CUR_BSSID, |
| /* Signed 8-bit value indicating the current RSSI */ |
| QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CUR_RSSI, |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_MAX = |
| QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_ndp_params - Used by the vendor command |
| * QCA_NL80211_VENDOR_SUBCMD_NDP. |
| */ |
| enum qca_wlan_vendor_attr_ndp_params { |
| QCA_WLAN_VENDOR_ATTR_NDP_PARAM_INVALID = 0, |
| /* Unsigned 32-bit value |
| * enum of sub commands values in qca_wlan_ndp_sub_cmd |
| */ |
| QCA_WLAN_VENDOR_ATTR_NDP_SUBCMD, |
| /* Unsigned 16-bit value */ |
| QCA_WLAN_VENDOR_ATTR_NDP_TRANSACTION_ID, |
| /* NL attributes for data used NDP SUB cmds */ |
| /* Unsigned 32-bit value indicating a service info */ |
| QCA_WLAN_VENDOR_ATTR_NDP_SERVICE_INSTANCE_ID, |
| /* Unsigned 32-bit value; channel frequency in MHz */ |
| QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL, |
| /* Interface Discovery MAC address. An array of 6 Unsigned int8 */ |
| QCA_WLAN_VENDOR_ATTR_NDP_PEER_DISCOVERY_MAC_ADDR, |
| /* Interface name on which NDP is being created */ |
| QCA_WLAN_VENDOR_ATTR_NDP_IFACE_STR, |
| /* Unsigned 32-bit value for security */ |
| /* CONFIG_SECURITY is deprecated, use NCS_SK_TYPE/PMK/SCID instead */ |
| QCA_WLAN_VENDOR_ATTR_NDP_CONFIG_SECURITY, |
| /* Unsigned 32-bit value for QoS */ |
| QCA_WLAN_VENDOR_ATTR_NDP_CONFIG_QOS, |
| /* Array of u8: len = QCA_WLAN_VENDOR_ATTR_NAN_DP_APP_INFO_LEN */ |
| QCA_WLAN_VENDOR_ATTR_NDP_APP_INFO, |
| /* Unsigned 32-bit value for NDP instance Id */ |
| QCA_WLAN_VENDOR_ATTR_NDP_INSTANCE_ID, |
| /* Array of instance Ids */ |
| QCA_WLAN_VENDOR_ATTR_NDP_INSTANCE_ID_ARRAY, |
| /* Unsigned 32-bit value for initiator/responder NDP response code |
| * accept/reject |
| */ |
| QCA_WLAN_VENDOR_ATTR_NDP_RESPONSE_CODE, |
| /* NDI MAC address. An array of 6 Unsigned int8 */ |
| QCA_WLAN_VENDOR_ATTR_NDP_NDI_MAC_ADDR, |
| /* Unsigned 32-bit value errors types returned by driver |
| * The wifi_nan.h in AOSP project platform/hardware/libhardware_legacy |
| * NanStatusType includes these values. |
| */ |
| QCA_WLAN_VENDOR_ATTR_NDP_DRV_RESPONSE_STATUS_TYPE, |
| /* Unsigned 32-bit value error values returned by driver |
| * The nan_i.h in AOSP project platform/hardware/qcom/wlan |
| * NanInternalStatusType includes these values. |
| */ |
| QCA_WLAN_VENDOR_ATTR_NDP_DRV_RETURN_VALUE, |
| /* Unsigned 32-bit value for Channel setup configuration |
| * The wifi_nan.h in AOSP project platform/hardware/libhardware_legacy |
| * NanDataPathChannelCfg includes these values. |
| */ |
| QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL_CONFIG, |
| /* Unsigned 32-bit value for Cipher Suite Shared Key Type */ |
| QCA_WLAN_VENDOR_ATTR_NDP_CSID, |
| /* Array of u8: len = NAN_PMK_INFO_LEN 32 bytes */ |
| QCA_WLAN_VENDOR_ATTR_NDP_PMK, |
| /* Security Context Identifier that contains the PMKID |
| * Array of u8: len = NAN_SCID_BUF_LEN 1024 bytes |
| */ |
| QCA_WLAN_VENDOR_ATTR_NDP_SCID, |
| /* Array of u8: len = NAN_SECURITY_MAX_PASSPHRASE_LEN 63 bytes */ |
| QCA_WLAN_VENDOR_ATTR_NDP_PASSPHRASE, |
| /* Array of u8: len = NAN_MAX_SERVICE_NAME_LEN 255 bytes */ |
| QCA_WLAN_VENDOR_ATTR_NDP_SERVICE_NAME, |
| /* Unsigned 32-bit bitmap indicating schedule update |
| * BIT_0: NSS Update |
| * BIT_1: Channel list update |
| */ |
| QCA_WLAN_VENDOR_ATTR_NDP_SCHEDULE_UPDATE_REASON, |
| /* Unsigned 32-bit value for NSS */ |
| QCA_WLAN_VENDOR_ATTR_NDP_NSS, |
| /* Unsigned 32-bit value for NUMBER NDP CHANNEL */ |
| QCA_WLAN_VENDOR_ATTR_NDP_NUM_CHANNELS, |
| /* Unsigned 32-bit value for CHANNEL BANDWIDTH |
| * 0:20 MHz, 1:40 MHz, 2:80 MHz, 3:160 MHz |
| */ |
| QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL_WIDTH, |
| /* Array of channel/band width */ |
| QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL_INFO, |
| /* IPv6 address used by NDP (in network byte order), 16 bytes array. |
| * This attribute is used and optional for ndp request, ndp response, |
| * ndp indication, and ndp confirm. |
| */ |
| QCA_WLAN_VENDOR_ATTR_NDP_IPV6_ADDR = 27, |
| /* Unsigned 16-bit value indicating transport port used by NDP. |
| * This attribute is used and optional for ndp response, ndp indication, |
| * and ndp confirm. |
| */ |
| QCA_WLAN_VENDOR_ATTR_NDP_TRANSPORT_PORT = 28, |
| /* Unsigned 8-bit value indicating protocol used by NDP and assigned by |
| * the Internet Assigned Numbers Authority (IANA) as per: |
| * https://www.iana.org/assignments/protocol-numbers/protocol-numbers.xhtml |
| * This attribute is used and optional for ndp response, ndp indication, |
| * and ndp confirm. |
| */ |
| QCA_WLAN_VENDOR_ATTR_NDP_TRANSPORT_PROTOCOL = 29, |
| /* Unsigned 8-bit value indicating if NDP remote peer supports NAN NDPE. |
| * 1:support 0:not support |
| */ |
| QCA_WLAN_VENDOR_ATTR_PEER_NDPE_SUPPORT = 30, |
| /* As per Wi-Fi Aware Specification v3.2 Service Id is the first |
| * 48 bits of the SHA-256 hash of the Service Name. |
| * A lower-case representation of the Service Name shall be used to |
| * calculate the Service ID. |
| * Array of u8: length is 6 bytes |
| * This attribute is used and optional for ndp indication. |
| */ |
| QCA_WLAN_VENDOR_ATTR_NDP_SERVICE_ID = 31, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_NDP_PARAMS_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_NDP_PARAMS_MAX = |
| QCA_WLAN_VENDOR_ATTR_NDP_PARAMS_AFTER_LAST - 1, |
| }; |
| |
| enum qca_wlan_ndp_sub_cmd { |
| QCA_WLAN_VENDOR_ATTR_NDP_INVALID = 0, |
| /* Command to create a NAN data path interface. |
| * This command was initially designed to both create and start a NAN |
| * data path interface. However, changes to Linux 5.12 no longer allow |
| * interface creation via vendor commands. When the driver advertises |
| * QCA_WLAN_VENDOR_FEATURE_USE_ADD_DEL_VIRTUAL_INTF_FOR_NDI |
| * userspace must explicitly first create the interface using |
| * NL80211_CMD_NEW_INTERFACE before subsequently invoking this command |
| * to start the interface. |
| */ |
| QCA_WLAN_VENDOR_ATTR_NDP_INTERFACE_CREATE = 1, |
| /* Command to delete a NAN data path interface. |
| * This command was initially designed to both stop and delete a NAN |
| * data path interface. However, changes to Linux 5.12 no longer allow |
| * interface deletion via vendor commands. When the driver advertises |
| * QCA_WLAN_VENDOR_FEATURE_USE_ADD_DEL_VIRTUAL_INTF_FOR_NDI |
| * userspace must explicitly delete the interface using |
| * NL80211_CMD_DEL_INTERFACE after calling this command. |
| */ |
| QCA_WLAN_VENDOR_ATTR_NDP_INTERFACE_DELETE = 2, |
| /* Command to initiate a NAN data path session */ |
| QCA_WLAN_VENDOR_ATTR_NDP_INITIATOR_REQUEST = 3, |
| /* Command to notify if the NAN data path session was sent */ |
| QCA_WLAN_VENDOR_ATTR_NDP_INITIATOR_RESPONSE = 4, |
| /* Command to respond to NAN data path session */ |
| QCA_WLAN_VENDOR_ATTR_NDP_RESPONDER_REQUEST = 5, |
| /* Command to notify on the responder about the response */ |
| QCA_WLAN_VENDOR_ATTR_NDP_RESPONDER_RESPONSE = 6, |
| /* Command to initiate a NAN data path end */ |
| QCA_WLAN_VENDOR_ATTR_NDP_END_REQUEST = 7, |
| /* Command to notify the if end request was sent */ |
| QCA_WLAN_VENDOR_ATTR_NDP_END_RESPONSE = 8, |
| /* Command to notify the peer about the end request */ |
| QCA_WLAN_VENDOR_ATTR_NDP_REQUEST_IND = 9, |
| /* Command to confirm the NAN data path session is complete */ |
| QCA_WLAN_VENDOR_ATTR_NDP_CONFIRM_IND = 10, |
| /* Command to indicate the peer about the end request being received */ |
| QCA_WLAN_VENDOR_ATTR_NDP_END_IND = 11, |
| /* Command to indicate the peer of schedule update */ |
| QCA_WLAN_VENDOR_ATTR_NDP_SCHEDULE_UPDATE_IND = 12 |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_nd_offload - Used by the vendor command |
| * QCA_NL80211_VENDOR_SUBCMD_ND_OFFLOAD. |
| */ |
| enum qca_wlan_vendor_attr_nd_offload { |
| QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_INVALID = 0, |
| /* Flag to set Neighbour Discovery offload */ |
| QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_FLAG, |
| /* Keep last */ |
| QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_MAX = |
| QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum packet_filter_sub_cmd - Packet filter sub commands |
| */ |
| enum packet_filter_sub_cmd { |
| /** |
| * Write packet filter program and/or data. The driver/firmware should |
| * disable APF before writing into local buffer and re-enable APF after |
| * writing is done. |
| */ |
| QCA_WLAN_SET_PACKET_FILTER = 1, |
| /* Get packet filter feature capabilities from driver */ |
| QCA_WLAN_GET_PACKET_FILTER = 2, |
| /** |
| * Write packet filter program and/or data. User space will send the |
| * %QCA_WLAN_DISABLE_PACKET_FILTER command before issuing this command |
| * and will send the %QCA_WLAN_ENABLE_PACKET_FILTER afterwards. The key |
| * difference from that %QCA_WLAN_SET_PACKET_FILTER is the control over |
| * enable/disable is given to user space with this command. Also, |
| * user space sends the length of program portion in the buffer within |
| * %QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_PROG_LENGTH. |
| */ |
| QCA_WLAN_WRITE_PACKET_FILTER = 3, |
| /* Read packet filter program and/or data */ |
| QCA_WLAN_READ_PACKET_FILTER = 4, |
| /* Enable APF feature */ |
| QCA_WLAN_ENABLE_PACKET_FILTER = 5, |
| /* Disable APF feature */ |
| QCA_WLAN_DISABLE_PACKET_FILTER = 6, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_packet_filter - BPF control commands used by |
| * vendor QCA_NL80211_VENDOR_SUBCMD_PACKET_FILTER. |
| */ |
| enum qca_wlan_vendor_attr_packet_filter { |
| QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_INVALID = 0, |
| /* Unsigned 32-bit enum passed using packet_filter_sub_cmd */ |
| QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_SUB_CMD, |
| /* Unsigned 32-bit value indicating the packet filter version */ |
| QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_VERSION, |
| /* Unsigned 32-bit value indicating the packet filter id */ |
| QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_ID, |
| /** |
| * Unsigned 32-bit value indicating the packet filter size including |
| * program + data. |
| */ |
| QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_SIZE, |
| /* Unsigned 32-bit value indicating the packet filter current offset */ |
| QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_CURRENT_OFFSET, |
| /* Program and/or data in bytes */ |
| QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_PROGRAM, |
| /* Unsigned 32-bit value of the length of the program section in packet |
| * filter buffer. |
| */ |
| QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_PROG_LENGTH = 7, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_MAX = |
| QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_drv_info - WLAN driver info used by vendor command |
| * QCA_NL80211_VENDOR_SUBCMD_GET_BUS_SIZE. |
| */ |
| enum qca_wlan_vendor_drv_info { |
| QCA_WLAN_VENDOR_ATTR_DRV_INFO_INVALID = 0, |
| /* Maximum Message size info between firmware & HOST |
| * Unsigned 32-bit value |
| */ |
| QCA_WLAN_VENDOR_ATTR_DRV_INFO_BUS_SIZE, |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_DRV_INFO_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_DRV_INFO_MAX = |
| QCA_WLAN_VENDOR_ATTR_DRV_INFO_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_wake_stats - Wake lock stats used by vendor |
| * command QCA_NL80211_VENDOR_SUBCMD_GET_WAKE_REASON_STATS. |
| */ |
| enum qca_wlan_vendor_attr_wake_stats { |
| QCA_WLAN_VENDOR_ATTR_WAKE_STATS_INVALID = 0, |
| /* Unsigned 32-bit value indicating the total count of wake event */ |
| QCA_WLAN_VENDOR_ATTR_WAKE_STATS_TOTAL_CMD_EVENT_WAKE, |
| /* Array of individual wake count, each index representing wake reason |
| */ |
| QCA_WLAN_VENDOR_ATTR_WAKE_STATS_CMD_EVENT_WAKE_CNT_PTR, |
| /* Unsigned 32-bit value representing wake count array */ |
| QCA_WLAN_VENDOR_ATTR_WAKE_STATS_CMD_EVENT_WAKE_CNT_SZ, |
| /* Unsigned 32-bit total wake count value of driver/fw */ |
| QCA_WLAN_VENDOR_ATTR_WAKE_STATS_TOTAL_DRIVER_FW_LOCAL_WAKE, |
| /* Array of wake stats of driver/fw */ |
| QCA_WLAN_VENDOR_ATTR_WAKE_STATS_DRIVER_FW_LOCAL_WAKE_CNT_PTR, |
| /* Unsigned 32-bit total wake count value of driver/fw */ |
| QCA_WLAN_VENDOR_ATTR_WAKE_STATS_DRIVER_FW_LOCAL_WAKE_CNT_SZ, |
| /* Unsigned 32-bit total wake count value of packets received */ |
| QCA_WLAN_VENDOR_ATTR_WAKE_STATS_TOTAL_RX_DATA_WAKE, |
| /* Unsigned 32-bit wake count value unicast packets received */ |
| QCA_WLAN_VENDOR_ATTR_WAKE_STATS_RX_UNICAST_CNT, |
| /* Unsigned 32-bit wake count value multicast packets received */ |
| QCA_WLAN_VENDOR_ATTR_WAKE_STATS_RX_MULTICAST_CNT, |
| /* Unsigned 32-bit wake count value broadcast packets received */ |
| QCA_WLAN_VENDOR_ATTR_WAKE_STATS_RX_BROADCAST_CNT, |
| /* Unsigned 32-bit wake count value of ICMP packets */ |
| QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP_PKT, |
| /* Unsigned 32-bit wake count value of ICMP6 packets */ |
| QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP6_PKT, |
| /* Unsigned 32-bit value ICMP6 router advertisement */ |
| QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP6_RA, |
| /* Unsigned 32-bit value ICMP6 neighbor advertisement */ |
| QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP6_NA, |
| /* Unsigned 32-bit value ICMP6 neighbor solicitation */ |
| QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP6_NS, |
| /* Unsigned 32-bit wake count value of receive side ICMP4 multicast */ |
| QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP4_RX_MULTICAST_CNT, |
| /* Unsigned 32-bit wake count value of receive side ICMP6 multicast */ |
| QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP6_RX_MULTICAST_CNT, |
| /* Unsigned 32-bit wake count value of receive side multicast */ |
| QCA_WLAN_VENDOR_ATTR_WAKE_STATS_OTHER_RX_MULTICAST_CNT, |
| /* Unsigned 32-bit wake count value of a given RSSI breach */ |
| QCA_WLAN_VENDOR_ATTR_WAKE_STATS_RSSI_BREACH_CNT, |
| /* Unsigned 32-bit wake count value of low RSSI */ |
| QCA_WLAN_VENDOR_ATTR_WAKE_STATS_LOW_RSSI_CNT, |
| /* Unsigned 32-bit value GSCAN count */ |
| QCA_WLAN_VENDOR_ATTR_WAKE_STATS_GSCAN_CNT, |
| /* Unsigned 32-bit value PNO complete count */ |
| QCA_WLAN_VENDOR_ATTR_WAKE_STATS_PNO_COMPLETE_CNT, |
| /* Unsigned 32-bit value PNO match count */ |
| QCA_WLAN_VENDOR_ATTR_WAKE_STATS_PNO_MATCH_CNT, |
| /* keep last */ |
| QCA_WLAN_VENDOR_GET_WAKE_STATS_AFTER_LAST, |
| QCA_WLAN_VENDOR_GET_WAKE_STATS_MAX = |
| QCA_WLAN_VENDOR_GET_WAKE_STATS_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_thermal_level - Defines various thermal levels |
| * configured by userspace to the driver/firmware. |
| * The values can be encapsulated in QCA_WLAN_VENDOR_ATTR_THERMAL_LEVEL or |
| * QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_LEVEL attribute. |
| * The driver/firmware takes actions requested by userspace such as throttling |
| * wifi TX etc. in order to mitigate high temperature. |
| * |
| * @QCA_WLAN_VENDOR_THERMAL_LEVEL_NONE: Stop/clear all throttling actions. |
| * @QCA_WLAN_VENDOR_THERMAL_LEVEL_LIGHT: Throttle TX lightly. |
| * @QCA_WLAN_VENDOR_THERMAL_LEVEL_MODERATE: Throttle TX moderately. |
| * @QCA_WLAN_VENDOR_THERMAL_LEVEL_SEVERE: Throttle TX severely. |
| * @QCA_WLAN_VENDOR_THERMAL_LEVEL_CRITICAL: Critical thermal level reached. |
| * @QCA_WLAN_VENDOR_THERMAL_LEVEL_EMERGENCY: Emergency thermal level reached. |
| */ |
| enum qca_wlan_vendor_thermal_level { |
| QCA_WLAN_VENDOR_THERMAL_LEVEL_NONE = 0, |
| QCA_WLAN_VENDOR_THERMAL_LEVEL_LIGHT = 1, |
| QCA_WLAN_VENDOR_THERMAL_LEVEL_MODERATE = 2, |
| QCA_WLAN_VENDOR_THERMAL_LEVEL_SEVERE = 3, |
| QCA_WLAN_VENDOR_THERMAL_LEVEL_CRITICAL = 4, |
| QCA_WLAN_VENDOR_THERMAL_LEVEL_EMERGENCY = 5, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_thermal_cmd - Vendor subcmd attributes to set |
| * cmd value. Used for NL attributes for data used by |
| * QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD sub command. |
| */ |
| enum qca_wlan_vendor_attr_thermal_cmd { |
| QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_INVALID = 0, |
| /* The value of command, driver will implement different operations |
| * according to this value. It uses values defined in |
| * enum qca_wlan_vendor_attr_thermal_cmd_type. |
| * u32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_VALUE = 1, |
| /* Userspace uses this attribute to configure thermal level to the |
| * driver/firmware, or get thermal level from the driver/firmware. |
| * Used in request or response, u32 attribute, |
| * possible values are defined in enum qca_wlan_vendor_thermal_level. |
| */ |
| QCA_WLAN_VENDOR_ATTR_THERMAL_LEVEL = 2, |
| /* Userspace uses this attribute to configure the time in which the |
| * driver/firmware should complete applying settings it received from |
| * userspace with QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_SET_LEVEL |
| * command type. Used in request, u32 attribute, value is in |
| * milliseconds. A value of zero indicates to apply the settings |
| * immediately. The driver/firmware can delay applying the configured |
| * thermal settings within the time specified in this attribute if |
| * there is any critical ongoing operation. |
| */ |
| QCA_WLAN_VENDOR_ATTR_THERMAL_COMPLETION_WINDOW = 3, |
| /* Nested attribute, the driver/firmware uses this attribute to report |
| * thermal statistics of different thermal levels to userspace when |
| * requested using the |
| * QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_THERMAL_STATS command |
| * type. This attribute contains a nested array of records of thermal |
| * statistics of multiple levels. The attributes used inside this nested |
| * attribute are defined in enum qca_wlan_vendor_attr_thermal_stats. |
| */ |
| QCA_WLAN_VENDOR_ATTR_THERMAL_STATS = 4, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_MAX = |
| QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_AFTER_LAST - 1 |
| }; |
| |
| /** |
| * qca_wlan_vendor_attr_thermal_cmd_type: Attribute values for |
| * QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_VALUE to the vendor subcmd |
| * QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD. This represents the |
| * thermal command types sent to driver. |
| * @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_PARAMS: Request to |
| * get thermal shutdown configuration parameters for display. Parameters |
| * responded from driver are defined in |
| * enum qca_wlan_vendor_attr_get_thermal_params_rsp. |
| * @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_TEMPERATURE: Request to |
| * get temperature. Host should respond with a temperature data. It is defined |
| * in enum qca_wlan_vendor_attr_thermal_get_temperature. |
| * @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_SUSPEND: Request to execute thermal |
| * suspend action. |
| * @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_RESUME: Request to execute thermal |
| * resume action. |
| * @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_SET_LEVEL: Configure thermal level to |
| * the driver/firmware. |
| * @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_LEVEL: Request to get the current |
| * thermal level from the driver/firmware. The driver should respond with a |
| * thermal level defined in enum qca_wlan_vendor_thermal_level. |
| * @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_THERMAL_STATS: Request to get the |
| * current thermal statistics from the driver/firmware. The driver should |
| * respond with statistics of all thermal levels encapsulated in the attribute |
| * QCA_WLAN_VENDOR_ATTR_THERMAL_STATS. |
| * @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_CLEAR_THERMAL_STATS: Request to clear |
| * the current thermal statistics for all thermal levels maintained in the |
| * driver/firmware and start counting from zero again. |
| */ |
| enum qca_wlan_vendor_attr_thermal_cmd_type { |
| QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_PARAMS, |
| QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_TEMPERATURE, |
| QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_SUSPEND, |
| QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_RESUME, |
| QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_SET_LEVEL, |
| QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_LEVEL, |
| QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_THERMAL_STATS, |
| QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_CLEAR_THERMAL_STATS, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_thermal_get_temperature - vendor subcmd attributes |
| * to get chip temperature by user. |
| * enum values are used for NL attributes for data used by |
| * QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_TEMPERATURE command for data used |
| * by QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD sub command. |
| */ |
| enum qca_wlan_vendor_attr_thermal_get_temperature { |
| QCA_WLAN_VENDOR_ATTR_THERMAL_GET_TEMPERATURE_INVALID = 0, |
| /* Temperature value (degree Celsius) from driver. |
| * u32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_THERMAL_GET_TEMPERATURE_DATA, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_THERMAL_GET_TEMPERATURE_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_THERMAL_GET_TEMPERATURE_MAX = |
| QCA_WLAN_VENDOR_ATTR_THERMAL_GET_TEMPERATURE_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_get_thermal_params_rsp - vendor subcmd attributes |
| * to get configuration parameters of thermal shutdown feature. Enum values are |
| * used by QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_PARAMS command for data |
| * used by QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD sub command. |
| */ |
| enum qca_wlan_vendor_attr_get_thermal_params_rsp { |
| QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_INVALID = 0, |
| /* Indicate if the thermal shutdown feature is enabled. |
| * NLA_FLAG attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_SHUTDOWN_EN, |
| /* Indicate if the auto mode is enabled. |
| * Enable: Driver triggers the suspend/resume action. |
| * Disable: User space triggers the suspend/resume action. |
| * NLA_FLAG attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_SHUTDOWN_AUTO_EN, |
| /* Thermal resume threshold (degree Celsius). Issue the resume command |
| * if the temperature value is lower than this threshold. |
| * u16 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_RESUME_THRESH, |
| /* Thermal warning threshold (degree Celsius). FW reports temperature |
| * to driver if it's higher than this threshold. |
| * u16 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_WARNING_THRESH, |
| /* Thermal suspend threshold (degree Celsius). Issue the suspend command |
| * if the temperature value is higher than this threshold. |
| * u16 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_SUSPEND_THRESH, |
| /* FW reports temperature data periodically at this interval (ms). |
| * u16 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_SAMPLE_RATE, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_MAX = |
| QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_thermal_event - vendor subcmd attributes to |
| * report thermal events from driver to user space. |
| * enum values are used for NL attributes for data used by |
| * QCA_NL80211_VENDOR_SUBCMD_THERMAL_EVENT sub command. |
| */ |
| enum qca_wlan_vendor_attr_thermal_event { |
| QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_INVALID = 0, |
| /* Temperature value (degree Celsius) from driver. |
| * u32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_TEMPERATURE, |
| /* Indication of resume completion from power save mode. |
| * NLA_FLAG attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_RESUME_COMPLETE, |
| /* Thermal level from the driver. |
| * u32 attribute. Possible values are defined in |
| * enum qca_wlan_vendor_thermal_level. |
| */ |
| QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_LEVEL = 3, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_MAX = |
| QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_thermal_stats - vendor subcmd attributes |
| * to get thermal status from the driver/firmware. |
| * enum values are used for NL attributes encapsulated inside the |
| * QCA_WLAN_VENDOR_ATTR_THERMAL_STATS nested attribute. |
| * |
| * QCA_WLAN_VENDOR_ATTR_THERMAL_STATS_MIN_TEMPERATURE: Minimum temperature |
| * of a thermal level in Celsius. u32 size. |
| * QCA_WLAN_VENDOR_ATTR_THERMAL_STATS_MAX_TEMPERATURE: Maximum temperature |
| * of a thermal level in Celsius. u32 size. |
| * QCA_WLAN_VENDOR_ATTR_THERMAL_STATS_DWELL_TIME: The total time spent on each |
| * thermal level in milliseconds. u32 size. |
| * QCA_WLAN_VENDOR_ATTR_THERMAL_STATS_TEMP_LEVEL_COUNTER: Indicates the number |
| * of times the temperature crossed into the temperature range defined by the |
| * thermal level from both higher and lower directions. u32 size. |
| */ |
| enum qca_wlan_vendor_attr_thermal_stats { |
| QCA_WLAN_VENDOR_ATTR_THERMAL_STATS_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_THERMAL_STATS_MIN_TEMPERATURE, |
| QCA_WLAN_VENDOR_ATTR_THERMAL_STATS_MAX_TEMPERATURE, |
| QCA_WLAN_VENDOR_ATTR_THERMAL_STATS_DWELL_TIME, |
| QCA_WLAN_VENDOR_ATTR_THERMAL_STATS_TEMP_LEVEL_COUNTER, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_THERMAL_STATS_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_THERMAL_STATS_MAX = |
| QCA_WLAN_VENDOR_ATTR_THERMAL_STATS_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum he_fragmentation_val - HE fragmentation support values |
| * Indicates level of dynamic fragmentation that is supported by |
| * a STA as a recipient. |
| * HE fragmentation values are defined in IEEE P802.11ax/D2.0, 9.4.2.237.2 |
| * (HE MAC Capabilities Information field) and are used in HE Capabilities |
| * element to advertise the support. These values are validated in the driver |
| * to check the device capability and advertised in the HE Capabilities |
| * element. These values are used to configure testbed device to allow the |
| * advertised hardware capabilities to be downgraded for testing purposes. |
| * |
| * @HE_FRAG_DISABLE: no support for dynamic fragmentation |
| * @HE_FRAG_LEVEL1: support for dynamic fragments that are |
| * contained within an MPDU or S-MPDU, no support for dynamic fragments |
| * within an A-MPDU that is not an S-MPDU. |
| * @HE_FRAG_LEVEL2: support for dynamic fragments that are |
| * contained within an MPDU or S-MPDU and support for up to one dynamic |
| * fragment for each MSDU, each A-MSDU if supported by the recipient, and |
| * each MMPDU within an A-MPDU or multi-TID A-MPDU that is not an |
| * MPDU or S-MPDU. |
| * @HE_FRAG_LEVEL3: support for dynamic fragments that are |
| * contained within an MPDU or S-MPDU and support for multiple dynamic |
| * fragments for each MSDU and for each A-MSDU if supported by the |
| * recipient within an A-MPDU or multi-TID AMPDU and up to one dynamic |
| * fragment for each MMPDU in a multi-TID A-MPDU that is not an S-MPDU. |
| */ |
| enum he_fragmentation_val { |
| HE_FRAG_DISABLE, |
| HE_FRAG_LEVEL1, |
| HE_FRAG_LEVEL2, |
| HE_FRAG_LEVEL3, |
| }; |
| |
| /** |
| * enum he_mcs_config - HE MCS support configuration |
| * |
| * Configures the HE Tx/Rx MCS map in HE capability IE for given bandwidth. |
| * These values are used in driver to configure the HE MCS map to advertise |
| * Tx/Rx MCS map in HE capability and these values are applied for all the |
| * streams supported by the device. To configure MCS for different bandwidths, |
| * vendor command needs to be sent using this attribute with appropriate value. |
| * For example, to configure HE_80_MCS_0_7, send vendor command using HE MCS |
| * attribute with HE_80_MCS0_7. And to configure HE MCS for HE_160_MCS0_11 |
| * send this command using HE MCS config attribute with value HE_160_MCS0_11. |
| * These values are used to configure testbed device to allow the advertised |
| * hardware capabilities to be downgraded for testing purposes. The enum values |
| * are defined such that BIT[1:0] indicates the MCS map value. Values 3,7 and |
| * 11 are not used as BIT[1:0] value is 3 which is used to disable MCS map. |
| * These values are validated in the driver before setting the MCS map and |
| * driver returns error if the input is other than these enum values. |
| * |
| * @HE_80_MCS0_7: support for HE 80/40/20 MHz MCS 0 to 7 |
| * @HE_80_MCS0_9: support for HE 80/40/20 MHz MCS 0 to 9 |
| * @HE_80_MCS0_11: support for HE 80/40/20 MHz MCS 0 to 11 |
| * @HE_160_MCS0_7: support for HE 160 MHz MCS 0 to 7 |
| * @HE_160_MCS0_9: support for HE 160 MHz MCS 0 to 9 |
| * @HE_160_MCS0_11: support for HE 160 MHz MCS 0 to 11 |
| * @HE_80P80_MCS0_7: support for HE 80p80 MHz MCS 0 to 7 |
| * @HE_80P80_MCS0_9: support for HE 80p80 MHz MCS 0 to 9 |
| * @HE_80P80_MCS0_11: support for HE 80p80 MHz MCS 0 to 11 |
| */ |
| enum he_mcs_config { |
| HE_80_MCS0_7 = 0, |
| HE_80_MCS0_9 = 1, |
| HE_80_MCS0_11 = 2, |
| HE_160_MCS0_7 = 4, |
| HE_160_MCS0_9 = 5, |
| HE_160_MCS0_11 = 6, |
| HE_80P80_MCS0_7 = 8, |
| HE_80P80_MCS0_9 = 9, |
| HE_80P80_MCS0_11 = 10, |
| }; |
| |
| /** |
| * enum qca_wlan_ba_session_config - BA session configuration |
| * |
| * Indicates the configuration values for BA session configuration attribute. |
| * |
| * @QCA_WLAN_ADD_BA: Establish a new BA session with given configuration. |
| * @QCA_WLAN_DELETE_BA: Delete the existing BA session for given TID. |
| */ |
| enum qca_wlan_ba_session_config { |
| QCA_WLAN_ADD_BA = 1, |
| QCA_WLAN_DELETE_BA = 2, |
| }; |
| |
| /** |
| * enum qca_wlan_ac_type - Access category type |
| * |
| * Indicates the access category type value. |
| * |
| * @QCA_WLAN_AC_BE: BE access category |
| * @QCA_WLAN_AC_BK: BK access category |
| * @QCA_WLAN_AC_VI: VI access category |
| * @QCA_WLAN_AC_VO: VO access category |
| * @QCA_WLAN_AC_ALL: All ACs |
| */ |
| enum qca_wlan_ac_type { |
| QCA_WLAN_AC_BE = 0, |
| QCA_WLAN_AC_BK = 1, |
| QCA_WLAN_AC_VI = 2, |
| QCA_WLAN_AC_VO = 3, |
| QCA_WLAN_AC_ALL = 4, |
| }; |
| |
| /** |
| * enum qca_wlan_he_ltf_cfg - HE LTF configuration |
| * |
| * Indicates the HE LTF configuration value. |
| * |
| * @QCA_WLAN_HE_LTF_AUTO: HE-LTF is automatically set to the mandatory HE-LTF, |
| * based on the GI setting |
| * @QCA_WLAN_HE_LTF_1X: 1X HE LTF is 3.2us LTF |
| * @QCA_WLAN_HE_LTF_2X: 2X HE LTF is 6.4us LTF |
| * @QCA_WLAN_HE_LTF_4X: 4X HE LTF is 12.8us LTF |
| */ |
| enum qca_wlan_he_ltf_cfg { |
| QCA_WLAN_HE_LTF_AUTO = 0, |
| QCA_WLAN_HE_LTF_1X = 1, |
| QCA_WLAN_HE_LTF_2X = 2, |
| QCA_WLAN_HE_LTF_4X = 3, |
| }; |
| |
| /** |
| * enum qca_wlan_he_mac_padding_dur - HE trigger frame MAC padding duration |
| * |
| * Indicates the HE trigger frame MAC padding duration value. |
| * |
| * @QCA_WLAN_HE_NO_ADDITIONAL_PROCESS_TIME: no additional time required to |
| * process the trigger frame. |
| * @QCA_WLAN_HE_8US_OF_PROCESS_TIME: indicates the 8us of processing time for |
| * trigger frame. |
| * @QCA_WLAN_HE_16US_OF_PROCESS_TIME: indicates the 16us of processing time for |
| * trigger frame. |
| */ |
| enum qca_wlan_he_mac_padding_dur { |
| QCA_WLAN_HE_NO_ADDITIONAL_PROCESS_TIME = 0, |
| QCA_WLAN_HE_8US_OF_PROCESS_TIME = 1, |
| QCA_WLAN_HE_16US_OF_PROCESS_TIME = 2, |
| }; |
| |
| /** |
| * enum qca_wlan_he_om_ctrl_ch_bw - HE OM control field BW configuration |
| * |
| * Indicates the HE Operating mode control channel width setting value. |
| * |
| * @QCA_WLAN_HE_OM_CTRL_BW_20M: Primary 20 MHz |
| * @QCA_WLAN_HE_OM_CTRL_BW_40M: Primary 40 MHz |
| * @QCA_WLAN_HE_OM_CTRL_BW_80M: Primary 80 MHz |
| * @QCA_WLAN_HE_OM_CTRL_BW_160M: 160 MHz and 80+80 MHz |
| */ |
| enum qca_wlan_he_om_ctrl_ch_bw { |
| QCA_WLAN_HE_OM_CTRL_BW_20M = 0, |
| QCA_WLAN_HE_OM_CTRL_BW_40M = 1, |
| QCA_WLAN_HE_OM_CTRL_BW_80M = 2, |
| QCA_WLAN_HE_OM_CTRL_BW_160M = 3, |
| }; |
| |
| /** |
| * enum qca_wlan_keep_alive_data_type - Keep alive data type configuration |
| * |
| * Indicates the frame types to use for keep alive data. |
| * |
| * @QCA_WLAN_KEEP_ALIVE_DEFAULT: Driver default type used for keep alive. |
| * @QCA_WLAN_KEEP_ALIVE_DATA: Data frame type for keep alive. |
| * @QCA_WLAN_KEEP_ALIVE_MGMT: Management frame type for keep alive. |
| */ |
| enum qca_wlan_keep_alive_data_type { |
| QCA_WLAN_KEEP_ALIVE_DEFAULT = 0, |
| QCA_WLAN_KEEP_ALIVE_DATA = 1, |
| QCA_WLAN_KEEP_ALIVE_MGMT = 2, |
| }; |
| |
| /** |
| * enum eht_mcs_config - EHT MCS support configuration |
| * |
| * Configures the EHT Tx/Rx MCS map in EHT Capability element. |
| * These values are used in the driver to configure the EHT MCS map to advertise |
| * Tx/Rx MCS map in EHT capability and these values are applied for all the |
| * streams supported by the device. |
| * @EHT_MCS0_7: EHT MCS 0 to 7 support |
| * @EHT_MCS0_9: EHT MCS 0 to 9 support |
| * @EHT_MCS0_11: EHT MCS 0 to 11 support |
| * @EHT_MCS0_13: EHT MCS 0 to 13 support |
| */ |
| enum eht_mcs_config { |
| EHT_MCS0_7 = 0, |
| EHT_MCS0_9 = 1, |
| EHT_MCS0_11 = 2, |
| EHT_MCS0_13 = 3, |
| }; |
| |
| /** |
| * enum qca_wlan_eht_mlo_mode: EHT MLO mode configuration. |
| * @QCA_WLAN_EHT_MODE_INVALID: Invalid. |
| * @QCA_WLAN_EHT_MLSR: Multi-link single radio mode |
| * @QCA_WLAN_EHT_EMLSR: Enhanced multi-link single radio mode. |
| * @QCA_WLAN_EHT_NON_STR_MLMR: Non simultaneous transmit and receive |
| * multi-link multi radio mode. |
| * @QCA_WLAN_EHT_STR_MLMR: Simultaneous transmit and receive |
| * multi-link multi radio mode. |
| */ |
| enum qca_wlan_eht_mlo_mode { |
| QCA_WLAN_EHT_MODE_INVALID = 0, |
| QCA_WLAN_EHT_MLSR = 1, |
| QCA_WLAN_EHT_EMLSR = 2, |
| QCA_WLAN_EHT_NON_STR_MLMR = 3, |
| QCA_WLAN_EHT_STR_MLMR = 4, |
| }; |
| |
| /** |
| * enum qca_wlan_emlsr_mode: Enhanced Multi-link Single Radio mode configuration |
| * @QCA_WLAN_EMLSR_MODE_ENTER: Enter EMLSR mode |
| * @QCA_WLAN_EMLSR_MODE_EXIT: Exit EMLSR mode |
| */ |
| enum qca_wlan_emlsr_mode { |
| QCA_WLAN_EMLSR_MODE_ENTER = 0, |
| QCA_WLAN_EMLSR_MODE_EXIT = 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_omi_tx: Represents attributes for HE and |
| * EHT operating mode control transmit request. These attributes are |
| * sent as part of QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_OMI_TX and |
| * QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_HE_OMI_RX_NSS: Mandatory 8-bit unsigned value |
| * indicates the maximum number of spatial streams, NSS, that the STA |
| * supports in reception for PPDU bandwidths less than or equal to 80 MHz |
| * and is set to NSS - 1. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_HE_OMI_CH_BW: Mandatory 8-bit unsigned value |
| * indicates the operating channel width supported by the STA for both |
| * reception and transmission. Uses enum qca_wlan_he_om_ctrl_ch_bw values. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_HE_OMI_ULMU_DISABLE: Mandatory 8-bit unsigned value |
| * indicates the all trigger based UL MU operations by the STA. |
| * 0 - UL MU operations are enabled by the STA. |
| * 1 - All triggered UL MU transmissions are suspended by the STA. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_HE_OMI_TX_NSTS: Mandatory 8-bit unsigned value |
| * indicates the maximum number of space-time streams, NSTS, that |
| * the STA supports in transmission and is set to NSTS - 1. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_HE_OMI_ULMU_DATA_DISABLE: 8-bit unsigned value |
| * combined with the UL MU Disable subfield and the recipient's setting |
| * of the OM Control UL MU Data Disable RX Support subfield in the HE MAC |
| * capabilities to determine which HE TB PPDUs are possible by the |
| * STA to transmit. |
| * 0 - UL MU data operations are enabled by the STA. |
| * 1 - Determine which HE TB PPDU types are allowed by the STA if UL MU disable |
| * bit is not set, else UL MU Tx is suspended. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_EHT_OMI_RX_NSS_EXTN: 8-bit unsigned value in the EHT OM |
| * Control subfield combined with the Rx NSS subfield in the OM Control subfield |
| * indicates NSS - 1, where NSS is the maximum number of spatial streams that |
| * STA supports in reception for PPDU bandwidths less than or equal to 80 MHz. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_EHT_OMI_CH_BW_EXTN: 8-bit unsigned value indicates |
| * 320 MHz operating channel width supported by the EHT STA for both reception |
| * and transmission. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_EHT_OMI_TX_NSS_EXTN: 8-bit unsigned value in the EHT OM |
| * Control subfield combined with the Tx NSTS subfield in OM Control subfield |
| * indicates NSTS - 1, where NSTS is the maximum number of space-time streams |
| * that the STA supports in transmission for PPDU bandwidths less than or equal |
| * to 80 MHz. |
| */ |
| enum qca_wlan_vendor_attr_omi_tx { |
| QCA_WLAN_VENDOR_ATTR_HE_OMI_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_HE_OMI_RX_NSS = 1, |
| QCA_WLAN_VENDOR_ATTR_HE_OMI_CH_BW = 2, |
| QCA_WLAN_VENDOR_ATTR_HE_OMI_ULMU_DISABLE = 3, |
| QCA_WLAN_VENDOR_ATTR_HE_OMI_TX_NSTS = 4, |
| QCA_WLAN_VENDOR_ATTR_HE_OMI_ULMU_DATA_DISABLE = 5, |
| QCA_WLAN_VENDOR_ATTR_EHT_OMI_RX_NSS_EXTN = 6, |
| QCA_WLAN_VENDOR_ATTR_EHT_OMI_CH_BW_EXTN = 7, |
| QCA_WLAN_VENDOR_ATTR_EHT_OMI_TX_NSS_EXTN = 8, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_OMI_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_OMI_MAX = |
| QCA_WLAN_VENDOR_ATTR_OMI_AFTER_LAST - 1, |
| }; |
| |
| /* deprecated legacy names */ |
| #define QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_OMI_TX \ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_OMI_TX |
| #define qca_wlan_vendor_attr_he_omi_tx \ |
| qca_wlan_vendor_attr_omi_tx |
| #define QCA_WLAN_VENDOR_ATTR_HE_OMI_AFTER_LAST \ |
| QCA_WLAN_VENDOR_ATTR_OMI_AFTER_LAST |
| #define QCA_WLAN_VENDOR_ATTR_HE_OMI_MAX \ |
| QCA_WLAN_VENDOR_ATTR_OMI_MAX |
| |
| /** |
| * enum qca_wlan_vendor_phy_mode - Different PHY modes |
| * These values are used with %QCA_WLAN_VENDOR_ATTR_CONFIG_PHY_MODE. |
| * |
| * @QCA_WLAN_VENDOR_PHY_MODE_AUTO: autoselect |
| * @QCA_WLAN_VENDOR_PHY_MODE_2G_AUTO: 2.4 GHz 802.11b/g/n/ax autoselect |
| * @QCA_WLAN_VENDOR_PHY_MODE_5G_AUTO: 5 GHz 802.11a/n/ac/ax autoselect |
| * @QCA_WLAN_VENDOR_PHY_MODE_11A: 5 GHz, OFDM |
| * @QCA_WLAN_VENDOR_PHY_MODE_11B: 2.4 GHz, CCK |
| * @QCA_WLAN_VENDOR_PHY_MODE_11G: 2.4 GHz, OFDM |
| * @QCA_WLAN_VENDOR_PHY_MODE_11AGN: Support 802.11n in both 2.4 GHz and 5 GHz |
| * @QCA_WLAN_VENDOR_PHY_MODE_11NG_HT20: 2.4 GHz, HT20 |
| * @QCA_WLAN_VENDOR_PHY_MODE_11NG_HT40PLUS: 2.4 GHz, HT40 (ext ch +1) |
| * @QCA_WLAN_VENDOR_PHY_MODE_11NG_HT40MINUS: 2.4 GHz, HT40 (ext ch -1) |
| * @QCA_WLAN_VENDOR_PHY_MODE_11NG_HT40: 2.4 GHz, Auto HT40 |
| * @QCA_WLAN_VENDOR_PHY_MODE_11NA_HT20: 5 GHz, HT20 |
| * @QCA_WLAN_VENDOR_PHY_MODE_11NA_HT40PLUS: 5 GHz, HT40 (ext ch +1) |
| * @QCA_WLAN_VENDOR_PHY_MODE_11NA_HT40MINUS: 5 GHz, HT40 (ext ch -1) |
| * @QCA_WLAN_VENDOR_PHY_MODE_11NA_HT40: 5 GHz, Auto HT40 |
| * @QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT20: 5 GHz, VHT20 |
| * @QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT40PLUS: 5 GHz, VHT40 (Ext ch +1) |
| * @QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT40MINUS: 5 GHz VHT40 (Ext ch -1) |
| * @QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT40: 5 GHz, VHT40 |
| * @QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT80: 5 GHz, VHT80 |
| * @QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT80P80: 5 GHz, VHT80+80 |
| * @QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT160: 5 GHz, VHT160 |
| * @QCA_WLAN_VENDOR_PHY_MODE_11AX_HE20: HE20 |
| * @QCA_WLAN_VENDOR_PHY_MODE_11AX_HE40: HE40 |
| * @QCA_WLAN_VENDOR_PHY_MODE_11AX_HE40PLUS: HE40 (ext ch +1) |
| * @QCA_WLAN_VENDOR_PHY_MODE_11AX_HE40MINUS: HE40 (ext ch -1) |
| * @QCA_WLAN_VENDOR_PHY_MODE_11AX_HE80: HE80 |
| * @QCA_WLAN_VENDOR_PHY_MODE_11AX_HE80P80: HE 80P80 |
| * @QCA_WLAN_VENDOR_PHY_MODE_11AX_HE160: HE160 |
| */ |
| enum qca_wlan_vendor_phy_mode { |
| QCA_WLAN_VENDOR_PHY_MODE_AUTO = 0, |
| QCA_WLAN_VENDOR_PHY_MODE_2G_AUTO = 1, |
| QCA_WLAN_VENDOR_PHY_MODE_5G_AUTO = 2, |
| QCA_WLAN_VENDOR_PHY_MODE_11A = 3, |
| QCA_WLAN_VENDOR_PHY_MODE_11B = 4, |
| QCA_WLAN_VENDOR_PHY_MODE_11G = 5, |
| QCA_WLAN_VENDOR_PHY_MODE_11AGN = 6, |
| QCA_WLAN_VENDOR_PHY_MODE_11NG_HT20 = 7, |
| QCA_WLAN_VENDOR_PHY_MODE_11NG_HT40PLUS = 8, |
| QCA_WLAN_VENDOR_PHY_MODE_11NG_HT40MINUS = 9, |
| QCA_WLAN_VENDOR_PHY_MODE_11NG_HT40 = 10, |
| QCA_WLAN_VENDOR_PHY_MODE_11NA_HT20 = 11, |
| QCA_WLAN_VENDOR_PHY_MODE_11NA_HT40PLUS = 12, |
| QCA_WLAN_VENDOR_PHY_MODE_11NA_HT40MINUS = 13, |
| QCA_WLAN_VENDOR_PHY_MODE_11NA_HT40 = 14, |
| QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT20 = 15, |
| QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT40PLUS = 16, |
| QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT40MINUS = 17, |
| QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT40 = 18, |
| QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT80 = 19, |
| QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT80P80 = 20, |
| QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT160 = 21, |
| QCA_WLAN_VENDOR_PHY_MODE_11AX_HE20 = 22, |
| QCA_WLAN_VENDOR_PHY_MODE_11AX_HE40 = 23, |
| QCA_WLAN_VENDOR_PHY_MODE_11AX_HE40PLUS = 24, |
| QCA_WLAN_VENDOR_PHY_MODE_11AX_HE40MINUS = 25, |
| QCA_WLAN_VENDOR_PHY_MODE_11AX_HE80 = 26, |
| QCA_WLAN_VENDOR_PHY_MODE_11AX_HE80P80 = 27, |
| QCA_WLAN_VENDOR_PHY_MODE_11AX_HE160 = 28, |
| }; |
| |
| /* Attributes for data used by |
| * QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION |
| */ |
| enum qca_wlan_vendor_attr_wifi_test_config { |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_INVALID = 0, |
| /* 8-bit unsigned value to configure the driver to enable/disable |
| * WMM feature. This attribute is used to configure testbed device. |
| * 1-enable, 0-disable |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_WMM_ENABLE = 1, |
| |
| /* 8-bit unsigned value to configure the driver to accept/reject |
| * the addba request from peer. This attribute is used to configure |
| * the testbed device. |
| * 1-accept addba, 0-reject addba |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ACCEPT_ADDBA_REQ = 2, |
| |
| /* 8-bit unsigned value to configure the driver to send or not to |
| * send the addba request to peer. |
| * This attribute is used to configure the testbed device. |
| * 1-send addba, 0-do not send addba |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_SEND_ADDBA_REQ = 3, |
| |
| /* 8-bit unsigned value to indicate the HE fragmentation support. |
| * Uses enum he_fragmentation_val values. |
| * This attribute is used to configure the testbed device to |
| * allow the advertised hardware capabilities to be downgraded |
| * for testing purposes. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_FRAGMENTATION = 4, |
| |
| /* 8-bit unsigned value to indicate the HE MCS support. |
| * Uses enum he_mcs_config values. |
| * This attribute is used to configure the testbed device to |
| * allow the advertised hardware capabilities to be downgraded |
| * for testing purposes. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MCS = 5, |
| |
| /* 8-bit unsigned value to configure the driver to allow or not to |
| * allow the connection with WEP/TKIP in HT/VHT/HE modes. |
| * This attribute is used to configure the testbed device. |
| * 1-allow WEP/TKIP in HT/VHT/HE, 0-do not allow WEP/TKIP. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_WEP_TKIP_IN_HE = 6, |
| |
| /* 8-bit unsigned value to configure the driver to add a |
| * new BA session or delete the existing BA session for |
| * given TID. ADDBA command uses the buffer size and TID |
| * configuration if user specifies the values else default |
| * value for buffer size is used for all TIDs if the TID |
| * also not specified. For DEL_BA command TID value is |
| * required to process the command. |
| * Uses enum qca_wlan_ba_session_config values. |
| * This attribute is used to configure the testbed device. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ADD_DEL_BA_SESSION = 7, |
| |
| /* 16-bit unsigned value to configure the buffer size in addba |
| * request and response frames. |
| * This attribute is used to configure the testbed device. |
| * The range of the value is 0 to 256. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ADDBA_BUFF_SIZE = 8, |
| |
| /* 8-bit unsigned value to configure the buffer size in addba |
| * request and response frames. |
| * This attribute is used to configure the testbed device. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_BA_TID = 9, |
| |
| /* 8-bit unsigned value to configure the no ack policy. |
| * To configure no ack policy, access category value is |
| * required to process the command. |
| * This attribute is used to configure the testbed device. |
| * 1 - enable no ack, 0 - disable no ack. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ENABLE_NO_ACK = 10, |
| |
| /* 8-bit unsigned value to configure the AC for no ack policy |
| * This attribute is used to configure the testbed device. |
| * Uses the enum qca_wlan_ac_type values. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_NO_ACK_AC = 11, |
| |
| /* 8-bit unsigned value to configure the HE LTF |
| * This attribute is used to configure the testbed device. |
| * Uses the enum qca_wlan_he_ltf_cfg values. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_LTF = 12, |
| |
| /* 8-bit unsigned value to configure the tx beamformee. |
| * This attribute is used to configure the testbed device. |
| * 1-enable, 0-disable. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ENABLE_TX_BEAMFORMEE = 13, |
| |
| /* 8-bit unsigned value to configure the tx beamformee number |
| * of space-time streams. |
| * This attribute is used to configure the testbed device. |
| * The range of the value is 0 to 8. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_TX_BEAMFORMEE_NSTS = 14, |
| |
| /* 8-bit unsigned value to configure the MU EDCA params for given AC |
| * This attribute is used to configure the testbed device. |
| * Uses the enum qca_wlan_ac_type values. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MU_EDCA_AC = 15, |
| |
| /* 8-bit unsigned value to configure the MU EDCA AIFSN for given AC |
| * To configure MU EDCA AIFSN value, MU EDCA access category value |
| * is required to process the command. |
| * This attribute is used to configure the testbed device. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MU_EDCA_AIFSN = 16, |
| |
| /* 8-bit unsigned value to configure the MU EDCA ECW min value for |
| * given AC. |
| * To configure MU EDCA ECW min value, MU EDCA access category value |
| * is required to process the command. |
| * This attribute is used to configure the testbed device. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MU_EDCA_ECWMIN = 17, |
| |
| /* 8-bit unsigned value to configure the MU EDCA ECW max value for |
| * given AC. |
| * To configure MU EDCA ECW max value, MU EDCA access category value |
| * is required to process the command. |
| * This attribute is used to configure the testbed device. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MU_EDCA_ECWMAX = 18, |
| |
| /* 8-bit unsigned value to configure the MU EDCA timer for given AC |
| * To configure MU EDCA timer value, MU EDCA access category value |
| * is required to process the command. |
| * This attribute is used to configure the testbed device. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MU_EDCA_TIMER = 19, |
| |
| /* 8-bit unsigned value to configure the HE trigger frame MAC padding |
| * duration. |
| * This attribute is used to configure the testbed device. |
| * Uses the enum qca_wlan_he_mac_padding_dur values. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MAC_PADDING_DUR = 20, |
| |
| /* 8-bit unsigned value to override the MU EDCA params to defaults |
| * regardless of the AP beacon MU EDCA params. If it is enabled use |
| * the default values else use the MU EDCA params from AP beacon. |
| * This attribute is used to configure the testbed device. |
| * 1-enable, 0-disable. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_OVERRIDE_MU_EDCA = 21, |
| |
| /* 8-bit unsigned value to configure the support for receiving |
| * an MPDU that contains an operating mode control subfield. |
| * This attribute is used to configure the testbed device. |
| * 1-enable, 0-disable. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_OM_CTRL_SUPP = 22, |
| |
| /* Nested attribute values required to setup the TWT session. |
| * enum qca_wlan_vendor_attr_twt_setup provides the necessary |
| * information to set up the session. It contains broadcast flags, |
| * set_up flags, trigger value, flow type, flow ID, wake interval |
| * exponent, protection, target wake time, wake duration, wake interval |
| * mantissa. These nested attributes are used to setup a host triggered |
| * TWT session. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_SETUP = 23, |
| |
| /* This nested attribute is used to terminate the current TWT session. |
| * It does not currently carry any attributes. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_TERMINATE = 24, |
| |
| /* This nested attribute is used to suspend the current TWT session. |
| * It does not currently carry any attributes. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_SUSPEND = 25, |
| |
| /* Nested attribute values to indicate the request for resume. |
| * This attribute is used to resume the TWT session. |
| * enum qca_wlan_vendor_attr_twt_resume provides the necessary |
| * parameters required to resume the TWT session. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_RESUME = 26, |
| |
| /* 8-bit unsigned value to set the HE operating mode control |
| * (OM CTRL) Channel Width subfield. |
| * The Channel Width subfield indicates the operating channel width |
| * supported by the STA for both reception and transmission. |
| * Uses the enum qca_wlan_he_om_ctrl_ch_bw values. |
| * This setting is cleared with the |
| * QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_CLEAR_HE_OM_CTRL_CONFIG |
| * flag attribute to reset defaults. |
| * This attribute is used to configure the testbed device. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_OM_CTRL_BW = 27, |
| |
| /* 8-bit unsigned value to configure the number of spatial |
| * streams in HE operating mode control field. |
| * This setting is cleared with the |
| * QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_CLEAR_HE_OM_CTRL_CONFIG |
| * flag attribute to reset defaults. |
| * This attribute is used to configure the testbed device. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_OM_CTRL_NSS = 28, |
| |
| /* Flag attribute to configure the UL MU disable bit in |
| * HE operating mode control field. |
| * This setting is cleared with the |
| * QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_CLEAR_HE_OM_CTRL_CONFIG |
| * flag attribute to reset defaults. |
| * This attribute is used to configure the testbed device. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_OM_CTRL_UL_MU_DISABLE = 29, |
| |
| /* Flag attribute to clear the previously set HE operating mode |
| * control field configuration. |
| * This attribute is used to configure the testbed device to reset |
| * defaults to clear any previously set HE operating mode control |
| * field configuration. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_CLEAR_HE_OM_CTRL_CONFIG = 30, |
| |
| /* 8-bit unsigned value to configure HE single user PPDU |
| * transmission. By default this setting is disabled and it |
| * is disabled in the reset defaults of the device configuration. |
| * This attribute is used to configure the testbed device. |
| * 1-enable, 0-disable |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_TX_SUPPDU = 31, |
| |
| /* 8-bit unsigned value to configure action frame transmission |
| * in HE trigger based PPDU transmission. |
| * By default this setting is disabled and it is disabled in |
| * the reset defaults of the device configuration. |
| * This attribute is used to configure the testbed device. |
| * 1-enable, 0-disable |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_ACTION_TX_TB_PPDU = 32, |
| |
| /* Nested attribute to indicate HE operating mode control field |
| * transmission. It contains operating mode control field Nss, |
| * channel bandwidth, Tx Nsts and UL MU disable attributes. |
| * These nested attributes are used to send HE operating mode control |
| * with configured values. |
| * Uses the enum qca_wlan_vendor_attr_omi_tx attributes. |
| * This attribute is used to configure the testbed device. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_OMI_TX = 33, |
| |
| /* 8-bit unsigned value to configure +HTC_HE support to indicate the |
| * support for the reception of a frame that carries an HE variant |
| * HT Control field. |
| * This attribute is used to configure the testbed device. |
| * 1-enable, 0-disable |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_HTC_HE_SUPP = 34, |
| |
| /* 8-bit unsigned value to configure VHT support in 2.4G band. |
| * This attribute is used to configure the testbed device. |
| * 1-enable, 0-disable |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ENABLE_2G_VHT = 35, |
| |
| /* 8-bit unsigned value to configure HE testbed defaults. |
| * This attribute is used to configure the testbed device. |
| * 1-set the device HE capabilities to testbed defaults. |
| * 0-reset the device HE capabilities to supported config. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_SET_HE_TESTBED_DEFAULTS = 36, |
| |
| /* 8-bit unsigned value to configure TWT request support. |
| * This attribute is used to configure the testbed device. |
| * 1-enable, 0-disable. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_TWT_REQ_SUPPORT = 37, |
| |
| /* 8-bit unsigned value to configure protection for Management |
| * frames when PMF is enabled for the association. |
| * This attribute is used to configure the testbed device. |
| * 0-use the correct key, 1-use an incorrect key, 2-disable protection. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_PMF_PROTECTION = 38, |
| |
| /* Flag attribute to inject Disassociation frame to the connected AP. |
| * This attribute is used to configure the testbed device. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_DISASSOC_TX = 39, |
| |
| /* 8-bit unsigned value to configure an override for the RSNXE Used |
| * subfield in the MIC control field of the FTE in FT Reassociation |
| * Request frame. |
| * 0 - Default behavior, 1 - override with 1, 2 - override with 0. |
| * This attribute is used to configure the testbed device. |
| * This attribute can be configured only when STA is in associated state |
| * and the configuration is valid until the disconnection. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_FT_REASSOCREQ_RSNXE_USED = 40, |
| |
| /* 8-bit unsigned value to configure the driver to ignore CSA (Channel |
| * Switch Announcement) when STA is in connected state. |
| * 0 - Default behavior, 1 - Ignore CSA. |
| * This attribute is used to configure the testbed device. |
| * This attribute can be configured only when STA is in associated state |
| * and the configuration is valid until the disconnection. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_IGNORE_CSA = 41, |
| |
| /* Nested attribute values required to configure OCI (Operating Channel |
| * Information). Attributes defined in enum |
| * qca_wlan_vendor_attr_oci_override are nested within this attribute. |
| * This attribute is used to configure the testbed device. |
| * This attribute can be configured only when STA is in associated state |
| * and the configuration is valid until the disconnection. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_OCI_OVERRIDE = 42, |
| |
| /* 8-bit unsigned value to configure the driver/firmware to ignore SA |
| * Query timeout. If this configuration is enabled STA shall not send |
| * Deauthentication frmae when SA Query times out (mainly, after a |
| * channel switch when OCV is enabled). |
| * 0 - Default behavior, 1 - Ignore SA Query timeout. |
| * This attribute is used to configure the testbed device. |
| * This attribute can be configured only when STA is in associated state |
| * and the configuration is valid until the disconnection. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_IGNORE_SA_QUERY_TIMEOUT = 43, |
| |
| /* 8-bit unsigned value to configure the driver/firmware to start or |
| * stop transmitting FILS discovery frames. |
| * 0 - Stop transmitting FILS discovery frames |
| * 1 - Start transmitting FILS discovery frames |
| * This attribute is used to configure the testbed device. |
| * This attribute can be configured only in AP mode and the |
| * configuration is valid until AP restart. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_FILS_DISCOVERY_FRAMES_TX = 44, |
| |
| /* 8-bit unsigned value to configure the driver/firmware to enable or |
| * disable full bandwidth UL MU-MIMO subfield in the HE PHY capabilities |
| * information field. |
| * 0 - Disable full bandwidth UL MU-MIMO subfield |
| * 1 - Enable full bandwidth UL MU-MIMO subfield |
| * This attribute is used to configure the testbed device. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_FULL_BW_UL_MU_MIMO = 45, |
| |
| /* 16-bit unsigned value to configure the driver with a specific BSS |
| * max idle period to advertise in the BSS Max Idle Period element |
| * (IEEE Std 802.11-2016, 9.4.2.79) in (Re)Association Request frames. |
| * This attribute is used to configure the testbed device. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_BSS_MAX_IDLE_PERIOD = 46, |
| |
| /* 8-bit unsigned value to configure the driver to use only RU 242 tone |
| * for data transmission. |
| * 0 - Default behavior, 1 - Configure RU 242 tone for data Tx. |
| * This attribute is used to configure the testbed device. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_RU_242_TONE_TX = 47, |
| |
| /* 8-bit unsigned value to configure the driver to disable data and |
| * management response frame transmission to test the BSS max idle |
| * feature. |
| * 0 - Default behavior, 1 - Disable data and management response Tx. |
| * This attribute is used to configure the testbed device. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_DISABLE_DATA_MGMT_RSP_TX = 48, |
| |
| /* 8-bit unsigned value to configure the driver/firmware to enable or |
| * disable Punctured Preamble Rx subfield in the HE PHY capabilities |
| * information field. |
| * 0 - Disable Punctured Preamble Rx subfield |
| * 1 - Enable Punctured Preamble Rx subfield |
| * This attribute is used to configure the testbed device. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_PUNCTURED_PREAMBLE_RX = 49, |
| |
| /* 8-bit unsigned value to configure the driver to ignore the SAE H2E |
| * requirement mismatch for 6 GHz connection. |
| * 0 - Default behavior, 1 - Ignore SAE H2E requirement mismatch. |
| * This attribute is used to configure the testbed device. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_IGNORE_H2E_RSNXE = 50, |
| |
| /* 8-bit unsigned value to configure the driver to allow 6 GHz |
| * connection with all security modes. |
| * 0 - Default behavior, 1 - Allow 6 GHz connection with all security |
| * modes. |
| * This attribute is used for testing purposes. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_6GHZ_SECURITY_TEST_MODE = 51, |
| |
| /* 8-bit unsigned value to configure the driver to transmit data with |
| * ER SU PPDU type. |
| * |
| * 0 - Default behavior, 1 - Enable ER SU PPDU type TX. |
| * This attribute is used for testing purposes. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ER_SU_PPDU_TYPE = 52, |
| |
| /* 8-bit unsigned value to configure the driver to use Data or |
| * Management frame type for keep alive data. |
| * Uses enum qca_wlan_keep_alive_data_type values. |
| * |
| * This attribute is used for testing purposes. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_KEEP_ALIVE_FRAME_TYPE = 53, |
| |
| /* 8-bit unsigned value to configure the driver to use scan request |
| * BSSID value in Probe Request frame RA(A1) during the scan. The |
| * driver saves this configuration and applies this setting to all user |
| * space scan requests until the setting is cleared. If this |
| * configuration is set, the driver uses the BSSID value from the scan |
| * request to set the RA(A1) in the Probe Request frames during the |
| * scan. |
| * |
| * 0 - Default behavior uses the broadcast RA in Probe Request frames. |
| * 1 - Uses the scan request BSSID in RA in Probe Request frames. |
| * This attribute is used for testing purposes. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_USE_BSSID_IN_PROBE_REQ_RA = 54, |
| |
| /* 8-bit unsigned value to configure the driver to enable/disable the |
| * BSS max idle period support. |
| * |
| * 0 - Disable the BSS max idle support. |
| * 1 - Enable the BSS max idle support. |
| * This attribute is used for testing purposes. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_BSS_MAX_IDLE_PERIOD_ENABLE = 55, |
| |
| /* 8-bit unsigned value to configure the driver/firmware to enable or |
| * disable Rx control frame to MultiBSS subfield in the HE MAC |
| * capabilities information field. |
| * 0 - Disable Rx control frame to MultiBSS subfield |
| * 1 - Enable Rx control frame to MultiBSS subfield |
| * This attribute is used to configure the testbed device. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_RX_CTRL_FRAME_TO_MBSS = 56, |
| |
| /* 8-bit unsigned value to configure the driver/firmware to enable or |
| * disable Broadcast TWT support subfield in the HE MAC capabilities |
| * information field. |
| * 0 - Disable Broadcast TWT support subfield |
| * 1 - Enable Broadcast TWT support subfield |
| * This attribute is used to configure the testbed device. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_BCAST_TWT_SUPPORT = 57, |
| |
| /* 8-bit unsigned value to configure the driver/firmware to allow eMLSR |
| * mode for IEEE 802.11be MLO capable devices. If the attribute is set |
| * to 1, and if the firmware supports this capability too, the STA |
| * advertises this capability to the AP over Association Request frame. |
| * This attribute will not have any effect on legacy devices with no |
| * IEEE 802.11be support. |
| * 0 - Default behavior |
| * 1 - Enable eMLSR (Enhanced Multi-link Single-Radio) mode |
| * This attribute is used to configure the testbed device. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_11BE_EMLSR_MODE = 58, |
| |
| /* 8-bit unsigned value to configure the driver to enable/disable the |
| * periodic sounding for Tx beamformer functionality. The default |
| * behavior uses algorithm to do sounding based on packet stats. |
| * |
| * 0 - Default behavior. |
| * 1 - Enable the periodic sounding for Tx beamformer. |
| * This attribute is used for testing purposes. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_BEAMFORMER_PERIODIC_SOUNDING = 59, |
| |
| /* 8-bit unsigned value to configure beamformee SS EHT capability |
| * to indicate the maximum number of spatial streams that the STA |
| * can receive in an EHT sounding NDP for <= 80 MHz bandwidth. |
| * The range of the value is 3 to 7. |
| * This attribute is used to configure the testbed device. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_EHT_BEAMFORMEE_SS_80MHZ = 60, |
| |
| /* 8-bit unsigned value to configure beamformee SS EHT capability |
| * to indicate the maximum number of spatial streams that the STA |
| * can receive in an EHT sounding NDP for 160 MHz bandwidth. |
| * The range of the value is 3 to 7. |
| * This attribute is used to configure the testbed device. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_EHT_BEAMFORMEE_SS_160MHZ = 61, |
| |
| /* 8-bit unsigned value to configure beamformee SS EHT capability |
| * to indicate the maximum number of spatial streams that the STA |
| * can receive in an EHT sounding NDP for 320 MHz bandwidth. |
| * The range of the value is 3 to 7. |
| * This attribute is used to configure the testbed device. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_EHT_BEAMFORMEE_SS_320MHZ = 62, |
| |
| /* 8-bit unsigned value to configure the driver to exclude station |
| * profile in Probe Request frame Multi-Link element. |
| * 0 - Default behavior, sends the Probe Request frame with station |
| * profile data included in the Multi-Link element. |
| * 1 - Exclude station profile in Probe Request frame Multi-Link |
| * element. |
| * This attribute is used to configure the testbed device. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_EXCLUDE_STA_PROF_IN_PROBE_REQ = 63, |
| |
| /* 8-bit unsigned value to configure EHT testbed defaults. |
| * This attribute is used to configure the testbed device. |
| * 1 - Set the device EHT capabilities to testbed defaults. |
| * 0 - Reset the device EHT capabilities to supported config. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_SET_EHT_TESTBED_DEFAULTS = 64, |
| |
| /* 8-bit unsigned value to indicate the EHT MCS support. |
| * Uses enum eht_mcs_config values. |
| * This attribute is used to configure the testbed device to |
| * allow the advertised hardware capabilities to be downgraded |
| * for testing purposes. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_EHT_MCS = 65, |
| |
| /* 8-bit unsigned value to configure EHT TB Sounding Feedback |
| * Rate Limit capability. |
| * This attribute is used to configure the testbed device. |
| * 0 - Indicates no maximum supported data rate limitation. |
| * 1 - Indicates the maximum supported data rate is the lower of |
| * the 1500 Mb/s and the maximum supported data rate. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_EHT_TB_SOUNDING_FB_RL = 66, |
| |
| /* 8-bit unsigned value to configure the support for receiving an MPDU |
| * that contains an EHT operating mode control subfield. |
| * This attribute is used to configure the testbed device. |
| * 1-enable, 0-disable. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_EHT_OM_CTRL_SUPPORT = 67, |
| |
| /* 8-bit unsigned value to configure the driver with EMLSR padding delay |
| * subfield value. |
| * |
| * 0 - 0 us |
| * 1 - 32 us |
| * 2 - 64 us |
| * 3 - 128 us |
| * 4 - 256 us |
| * 5-255 - Reserved |
| * |
| * This attribute is used for testing purposes. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_EMLSR_PADDING_DELAY = 68, |
| |
| /* |
| * 8-bit unsigned value to indicate the firmware to force the active MLO |
| * links to power save mode for the configured number of beacon periods. |
| * This allows the firmware to suspend STA links for X beacon periods |
| * and remain asleep even if the AP advertises TIM as opposed to regular |
| * power save mode where STA links wake up if the AP indicates that it |
| * has buffered data to send. |
| * This attribute is used to configure the testbed device. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_FORCE_MLO_POWER_SAVE_BCN_PERIOD = 69, |
| |
| /* |
| * 8-bit unsigned value to indicate the firmware to be in STR MLMR mode |
| * to enable simultaneous transmission of PPDUs on all active links. |
| * 0 - Default behavior |
| * 1 - Enter STR mode for simultaneous data transmission on all links |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_EHT_MLO_STR_TX = 70, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_MAX = |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_twt_operation - Operation of the config TWT request |
| * Values for %QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_OPERATION. |
| * The response for the respective operations can be either synchronous or |
| * asynchronous (wherever specified). If synchronous, the response to this |
| * operation is obtained in the corresponding vendor command reply to the user |
| * space. For the asynchronous case the response is obtained as an event with |
| * the same operation type. |
| * |
| * Drivers shall support either of these modes but not both simultaneously. |
| * This support for asynchronous mode is advertised through the flag |
| * QCA_WLAN_VENDOR_FEATURE_TWT_ASYNC_SUPPORT. If this flag is not advertised, |
| * the driver shall support synchronous mode. |
| * |
| * @QCA_WLAN_TWT_SET: Setup a TWT session. Required parameters are configured |
| * through QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_PARAMS. Refers the enum |
| * qca_wlan_vendor_attr_twt_setup. Depending upon the |
| * @QCA_WLAN_VENDOR_FEATURE_TWT_ASYNC_SUPPORT capability, this is either a |
| * synchronous or asynchronous operation. |
| * |
| * @QCA_WLAN_TWT_GET: Get the configured TWT parameters. Required parameters are |
| * obtained through QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_PARAMS. Refers the enum |
| * qca_wlan_vendor_attr_twt_setup. This is a synchronous operation. |
| * |
| * @QCA_WLAN_TWT_TERMINATE: Terminate the TWT session. Required parameters are |
| * obtained through QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_PARAMS. Refers the enum |
| * qca_wlan_vendor_attr_twt_setup. Valid only after the TWT session is setup. |
| * This terminate can either get triggered by the user space or can as well be |
| * a notification from the firmware if it initiates a terminate. |
| * Depending upon the @QCA_WLAN_VENDOR_FEATURE_TWT_ASYNC_SUPPORT capability, |
| * the request from user space can either be a synchronous or asynchronous |
| * operation. |
| * |
| * @QCA_WLAN_TWT_SUSPEND: Suspend the TWT session. Required parameters are |
| * obtained through QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_PARAMS. Refers the enum |
| * qca_wlan_vendor_attr_twt_setup. Valid only after the TWT session is setup. |
| * Depending upon the @QCA_WLAN_VENDOR_FEATURE_TWT_ASYNC_SUPPORT capability, |
| * this is either a synchronous or asynchronous operation. |
| * |
| * @QCA_WLAN_TWT_RESUME: Resume the TWT session. Required parameters are |
| * configured through QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_PARAMS. Refers the enum |
| * qca_wlan_vendor_attr_twt_resume. Valid only after the TWT session is setup. |
| * This can as well be a notification from the firmware on a QCA_WLAN_TWT_NUDGE |
| * request. Depending upon the @QCA_WLAN_VENDOR_FEATURE_TWT_ASYNC_SUPPORT |
| * capability, this is either a synchronous or asynchronous operation. |
| * |
| * @QCA_WLAN_TWT_NUDGE: Suspend and resume the TWT session. TWT nudge is a |
| * combination of suspend and resume in a single request. Required parameters |
| * are configured through QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_PARAMS. Refers the |
| * enum qca_wlan_vendor_attr_twt_nudge. Valid only after the TWT session is |
| * setup. Depending upon the @QCA_WLAN_VENDOR_FEATURE_TWT_ASYNC_SUPPORT |
| * capability, this is either a synchronous or asynchronous operation. |
| * |
| * @QCA_WLAN_TWT_GET_STATS: Get the TWT session traffic statistics information. |
| * Refers the enum qca_wlan_vendor_attr_twt_stats. Valid only after the TWT |
| * session is setup. It's a synchronous operation. |
| * |
| * @QCA_WLAN_TWT_CLEAR_STATS: Clear TWT session traffic statistics information. |
| * Valid only after the TWT session is setup. It's a synchronous operation. |
| * |
| * @QCA_WLAN_TWT_GET_CAPABILITIES: Get TWT capabilities of this device and its |
| * peer. Refers the enum qca_wlan_vendor_attr_twt_capability. It's a synchronous |
| * operation. |
| * |
| * @QCA_WLAN_TWT_SETUP_READY_NOTIFY: Notify userspace that the firmware is |
| * ready for a new TWT session setup after it issued a TWT teardown. |
| * |
| * @QCA_WLAN_TWT_SET_PARAM: Configure TWT related parameters. Required |
| * parameters are obtained through QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_PARAMS. Refer |
| * the enum qca_wlan_vendor_attr_twt_set_param. |
| * |
| * @QCA_WLAN_TWT_NOTIFY: Used to notify userspace about changes in TWT |
| * related information for example TWT required bit in AP capabilities etc. |
| * The reason for the notification is sent using |
| * QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_NOTIFY_STATUS. |
| */ |
| enum qca_wlan_twt_operation { |
| QCA_WLAN_TWT_SET = 0, |
| QCA_WLAN_TWT_GET = 1, |
| QCA_WLAN_TWT_TERMINATE = 2, |
| QCA_WLAN_TWT_SUSPEND = 3, |
| QCA_WLAN_TWT_RESUME = 4, |
| QCA_WLAN_TWT_NUDGE = 5, |
| QCA_WLAN_TWT_GET_STATS = 6, |
| QCA_WLAN_TWT_CLEAR_STATS = 7, |
| QCA_WLAN_TWT_GET_CAPABILITIES = 8, |
| QCA_WLAN_TWT_SETUP_READY_NOTIFY = 9, |
| QCA_WLAN_TWT_SET_PARAM = 10, |
| QCA_WLAN_TWT_NOTIFY = 11, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_config_twt: Defines attributes used by |
| * %QCA_NL80211_VENDOR_SUBCMD_CONFIG_TWT. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_OPERATION: u8 attribute. Specify the TWT |
| * operation of this request. Possible values are defined in enum |
| * qca_wlan_twt_operation. The parameters for the respective operation is |
| * specified through QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_PARAMS. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_PARAMS: Nested attribute representing the |
| * parameters configured for TWT. These parameters are represented by |
| * enum qca_wlan_vendor_attr_twt_setup, enum qca_wlan_vendor_attr_twt_resume, |
| * enum qca_wlan_vendor_attr_twt_set_param, or |
| * enum qca_wlan_vendor_attr_twt_stats based on the operation. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_NOTIFY_STATUS: Size is u8, mandatory when |
| * QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_OPERATION is set to QCA_WLAN_TWT_NOTIFY. |
| * The values used by this attribute are defined in |
| * enum qca_wlan_vendor_twt_status. |
| */ |
| enum qca_wlan_vendor_attr_config_twt { |
| QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_OPERATION = 1, |
| QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_PARAMS = 2, |
| QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_NOTIFY_STATUS = 3, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_MAX = |
| QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_bss_filter - Used by the vendor command |
| * QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER. |
| * The user can add/delete the filter by specifying the BSSID/STA MAC address in |
| * QCA_WLAN_VENDOR_ATTR_BSS_FILTER_MAC_ADDR, filter type in |
| * QCA_WLAN_VENDOR_ATTR_BSS_FILTER_TYPE, add/delete action in |
| * QCA_WLAN_VENDOR_ATTR_BSS_FILTER_ACTION in the request. The user can get the |
| * statistics of an unassociated station by specifying the MAC address in |
| * QCA_WLAN_VENDOR_ATTR_BSS_FILTER_MAC_ADDR, station type in |
| * QCA_WLAN_VENDOR_ATTR_BSS_FILTER_TYPE, GET action in |
| * QCA_WLAN_VENDOR_ATTR_BSS_FILTER_ACTION in the request. The user also can get |
| * the statistics of all unassociated stations by specifying the Broadcast MAC |
| * address (ff:ff:ff:ff:ff:ff) in QCA_WLAN_VENDOR_ATTR_BSS_FILTER_MAC_ADDR with |
| * above procedure. In the response, driver shall specify statistics |
| * information nested in QCA_WLAN_VENDOR_ATTR_BSS_FILTER_STA_STATS. |
| */ |
| enum qca_wlan_vendor_attr_bss_filter { |
| QCA_WLAN_VENDOR_ATTR_BSS_FILTER_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_BSS_FILTER_MAC_ADDR = 1, |
| /* Other BSS filter type, unsigned 8 bit value. One of the values |
| * in enum qca_wlan_vendor_bss_filter_type. |
| */ |
| QCA_WLAN_VENDOR_ATTR_BSS_FILTER_TYPE = 2, |
| /* Other BSS filter action, unsigned 8 bit value. One of the values |
| * in enum qca_wlan_vendor_bss_filter_action. |
| */ |
| QCA_WLAN_VENDOR_ATTR_BSS_FILTER_ACTION = 3, |
| /* Array of nested attributes where each entry is the statistics |
| * information of the specified station that belong to another BSS. |
| * Attributes for each entry are taken from enum |
| * qca_wlan_vendor_bss_filter_sta_stats. |
| * Other BSS station configured in |
| * QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER with filter type |
| * QCA_WLAN_VENDOR_BSS_FILTER_TYPE_STA. |
| * Statistics returned by QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER |
| * with filter action QCA_WLAN_VENDOR_BSS_FILTER_ACTION_GET. |
| */ |
| QCA_WLAN_VENDOR_ATTR_BSS_FILTER_STA_STATS = 4, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_BSS_FILTER_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_BSS_FILTER_MAX = |
| QCA_WLAN_VENDOR_ATTR_BSS_FILTER_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_bss_filter_type - Type of |
| * filter used in other BSS filter operations. Used by the vendor command |
| * QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER. |
| * |
| * @QCA_WLAN_VENDOR_BSS_FILTER_TYPE_BSSID: BSSID filter |
| * @QCA_WLAN_VENDOR_BSS_FILTER_TYPE_STA: Station MAC address filter |
| */ |
| enum qca_wlan_vendor_bss_filter_type { |
| QCA_WLAN_VENDOR_BSS_FILTER_TYPE_BSSID, |
| QCA_WLAN_VENDOR_BSS_FILTER_TYPE_STA, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_bss_filter_action - Type of |
| * action in other BSS filter operations. Used by the vendor command |
| * QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER. |
| * |
| * @QCA_WLAN_VENDOR_BSS_FILTER_ACTION_ADD: Add filter |
| * @QCA_WLAN_VENDOR_BSS_FILTER_ACTION_DEL: Delete filter |
| * @QCA_WLAN_VENDOR_BSS_FILTER_ACTION_GET: Get the statistics |
| */ |
| enum qca_wlan_vendor_bss_filter_action { |
| QCA_WLAN_VENDOR_BSS_FILTER_ACTION_ADD, |
| QCA_WLAN_VENDOR_BSS_FILTER_ACTION_DEL, |
| QCA_WLAN_VENDOR_BSS_FILTER_ACTION_GET, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_bss_filter_sta_stats - Attributes for |
| * the statistics of a specific unassociated station belonging to another BSS. |
| * The statistics provides information of the unassociated station |
| * filtered by other BSS operation - such as MAC, signal value. |
| * Used by the vendor command QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER. |
| * |
| * @QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_MAC: MAC address of the station. |
| * @QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_RSSI: Last received signal strength |
| * of the station. Unsigned 8 bit number containing RSSI. |
| * @QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_RSSI_TS: Time stamp of the host |
| * driver for the last received RSSI. Unsigned 64 bit number containing |
| * nanoseconds from the boottime. |
| * @QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_PAD: Attribute used for padding for |
| * 64-bit alignment. |
| */ |
| enum qca_wlan_vendor_bss_filter_sta_stats { |
| QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_INVALID = 0, |
| QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_MAC = 1, |
| QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_RSSI = 2, |
| QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_RSSI_TS = 3, |
| QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_PAD = 4, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_AFTER_LAST, |
| QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_MAX = |
| QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_AFTER_LAST - 1 |
| }; |
| |
| /* enum qca_wlan_nan_subcmd_type - Type of NAN command used by attribute |
| * QCA_WLAN_VENDOR_ATTR_NAN_SUBCMD_TYPE as a part of vendor command |
| * QCA_NL80211_VENDOR_SUBCMD_NAN_EXT. |
| */ |
| enum qca_wlan_nan_ext_subcmd_type { |
| /* Subcmd of type NAN Enable Request */ |
| QCA_WLAN_NAN_EXT_SUBCMD_TYPE_ENABLE_REQ = 1, |
| /* Subcmd of type NAN Disable Request */ |
| QCA_WLAN_NAN_EXT_SUBCMD_TYPE_DISABLE_REQ = 2, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_nan_params - Used by the vendor command |
| * QCA_NL80211_VENDOR_SUBCMD_NAN_EXT. |
| */ |
| enum qca_wlan_vendor_attr_nan_params { |
| QCA_WLAN_VENDOR_ATTR_NAN_INVALID = 0, |
| /* Carries NAN command for firmware component. Every vendor command |
| * QCA_NL80211_VENDOR_SUBCMD_NAN_EXT must contain this attribute with a |
| * payload containing the NAN command. NLA_BINARY attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_NAN_CMD_DATA = 1, |
| /* Indicates the type of NAN command sent with |
| * QCA_NL80211_VENDOR_SUBCMD_NAN_EXT. enum qca_wlan_nan_ext_subcmd_type |
| * describes the possible range of values. This attribute is mandatory |
| * if the command being issued is either |
| * QCA_WLAN_NAN_EXT_SUBCMD_TYPE_ENABLE_REQ or |
| * QCA_WLAN_NAN_EXT_SUBCMD_TYPE_DISABLE_REQ. NLA_U32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_NAN_SUBCMD_TYPE = 2, |
| /* Frequency (in MHz) of primary NAN discovery social channel in 2.4 GHz |
| * band. This attribute is mandatory when command type is |
| * QCA_WLAN_NAN_EXT_SUBCMD_TYPE_ENABLE_REQ. NLA_U32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_NAN_DISC_24GHZ_BAND_FREQ = 3, |
| /* Frequency (in MHz) of secondary NAN discovery social channel in 5 GHz |
| * band. This attribute is optional and should be included when command |
| * type is QCA_WLAN_NAN_EXT_SUBCMD_TYPE_ENABLE_REQ and NAN discovery |
| * has to be started on 5GHz along with 2.4GHz. NLA_U32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_NAN_DISC_5GHZ_BAND_FREQ = 4, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_NAN_PARAMS_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_NAN_PARAMS_MAX = |
| QCA_WLAN_VENDOR_ATTR_NAN_PARAMS_AFTER_LAST - 1 |
| }; |
| |
| /** |
| * qca_wlan_twt_setup_state: Represents the TWT session states. |
| * |
| * QCA_WLAN_TWT_SETUP_STATE_NOT_ESTABLISHED: TWT session not established. |
| * QCA_WLAN_TWT_SETUP_STATE_ACTIVE: TWT session is active. |
| * QCA_WLAN_TWT_SETUP_STATE_SUSPEND: TWT session is in suspended state. |
| */ |
| enum qca_wlan_twt_setup_state { |
| QCA_WLAN_TWT_SETUP_STATE_NOT_ESTABLISHED = 0, |
| QCA_WLAN_TWT_SETUP_STATE_ACTIVE = 1, |
| QCA_WLAN_TWT_SETUP_STATE_SUSPEND = 2, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_twt_setup: Represents attributes for |
| * TWT (Target Wake Time) setup request. These attributes are sent as part of |
| * %QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_SETUP and |
| * %QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION. Also used by |
| * attributes through %QCA_NL80211_VENDOR_SUBCMD_CONFIG_TWT. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_BCAST: Flag attribute. |
| * Disable (flag attribute not present) - Individual TWT |
| * Enable (flag attribute present) - Broadcast TWT. |
| * Individual means the session is between the STA and the AP. |
| * This session is established using a separate negotiation between |
| * STA and AP. |
| * Broadcast means the session is across multiple STAs and an AP. The |
| * configuration parameters are announced in Beacon frames by the AP. |
| * This is used in |
| * 1. TWT SET Request and Response |
| * 2. TWT GET Response |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_REQ_TYPE: Required (u8). |
| * Unsigned 8-bit qca_wlan_vendor_twt_setup_req_type to |
| * specify the TWT request type. This is used in TWT SET operation. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_TRIGGER: Flag attribute |
| * Enable (flag attribute present) - TWT with trigger support. |
| * Disable (flag attribute not present) - TWT without trigger support. |
| * Trigger means the AP will send the trigger frame to allow STA to send data. |
| * Without trigger, the STA will wait for the MU EDCA timer before |
| * transmitting the data. |
| * This is used in |
| * 1. TWT SET Request and Response |
| * 2. TWT GET Response |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_FLOW_TYPE: Required (u8) |
| * 0 - Announced TWT - In this mode, STA may skip few service periods to |
| * save more power. If STA wants to wake up, it will send a PS-POLL/QoS |
| * NULL frame to AP. |
| * 1 - Unannounced TWT - The STA will wakeup during every SP. |
| * This is a required parameter for |
| * 1. TWT SET Request and Response |
| * 2. TWT GET Response |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_FLOW_ID: Optional (u8) |
| * Flow ID is the unique identifier for each TWT session. |
| * If not provided then dialog ID will be set to zero. |
| * This is an optional parameter for |
| * 1. TWT SET Request and Response |
| * 2. TWT GET Request and Response |
| * 3. TWT TERMINATE Request and Response |
| * 4. TWT SUSPEND Request and Response |
| * Flow ID values from 0 to 254 represent a single TWT session |
| * Flow ID value of 255 represents all TWT sessions for the following |
| * 1. TWT TERMINATE Request and Response |
| * 2. TWT SUSPEND Request and Response |
| * 4. TWT CLEAR STATISTICS request |
| * 5. TWT GET STATISTICS request and response |
| * If an invalid dialog ID is provided, status |
| * QCA_WLAN_VENDOR_TWT_STATUS_SESSION_NOT_EXIST will be returned. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL_EXP: Required (u8) |
| * This attribute (exp) is used along with the mantissa to derive the |
| * wake interval using the following formula: |
| * pow(2,exp) = wake_intvl_us/wake_intvl_mantis |
| * Wake interval is the interval between 2 successive SP. |
| * This is a required parameter for |
| * 1. TWT SET Request and Response |
| * 2. TWT GET Response |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_PROTECTION: Flag attribute |
| * Enable (flag attribute present) - Protection required. |
| * Disable (flag attribute not present) - Protection not required. |
| * If protection is enabled, then the AP will use protection |
| * mechanism using RTS/CTS to self to reserve the airtime. |
| * This is used in |
| * 1. TWT SET Request and Response |
| * 2. TWT GET Response |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_TIME: Optional (u32) |
| * This attribute is used as the SP offset which is the offset from |
| * TSF after which the wake happens. The units are in microseconds. If |
| * this attribute is not provided, then the value will be set to zero. |
| * This is an optional parameter for |
| * 1. TWT SET Request and Response |
| * 2. TWT GET Response |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_DURATION: Required (u32) |
| * This is the duration of the service period. This is specified as |
| * multiples of 256 microseconds. Valid values are 0x1 to 0xFF. |
| * This is a required parameter for |
| * 1. TWT SET Request and Response |
| * 2. TWT GET Response |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL_MANTISSA: Required (u32) |
| * This attribute is used to configure wake interval mantissa. |
| * The units are in TU. |
| * This is a required parameter for |
| * 1. TWT SET Request and Response |
| * 2. TWT GET Response |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_STATUS: Required (u8) |
| * This field is applicable for TWT response only. |
| * This contains status values in enum qca_wlan_vendor_twt_status |
| * and is passed to the userspace. This is used in TWT SET operation. |
| * This is a required parameter for |
| * 1. TWT SET Response |
| * 2. TWT TERMINATE Response |
| * 3. TWT SUSPEND Response |
| * 4. TWT RESUME Response |
| * 5. TWT NUDGE Response |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_RESP_TYPE: Required (u8) |
| * This field is applicable for TWT response only. |
| * This field contains response type from the TWT responder and is |
| * passed to the userspace. The values for this field are defined in |
| * enum qca_wlan_vendor_twt_setup_resp_type. This is used in TWT SET |
| * response. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_TIME_TSF: Required (u64) |
| * In TWT setup command this field contains absolute TSF that will |
| * be used by TWT requester during setup. |
| * In TWT response this field contains absolute TSF value of the |
| * wake time received from the TWT responder and is passed to |
| * the userspace. |
| * This is an optional parameter for |
| * 1. TWT SET Request |
| * This is a required parameter for |
| * 1. TWT SET Response |
| * 2. TWT GET Response |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_TWT_INFO_ENABLED: Flag attribute. |
| * Enable (flag attribute present) - Indicates that the TWT responder |
| * supports reception of TWT information frame from the TWT requestor. |
| * Disable (flag attribute not present) - Indicates that the responder |
| * doesn't support reception of TWT information frame from requestor. |
| * This is used in |
| * 1. TWT SET Response |
| * 2. TWT GET Response |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_MAC_ADDR: 6-byte MAC address |
| * Represents the MAC address of the peer for which the TWT session |
| * is being configured. This is used in AP mode to represent the respective |
| * client. |
| * In AP mode, this is a required parameter in response for |
| * 1. TWT SET |
| * 2. TWT GET |
| * 3. TWT TERMINATE |
| * 4. TWT SUSPEND |
| * In STA mode, this is an optional parameter in request and response for |
| * the above four TWT operations. |
| * In AP mode, this is a required parameter in request for |
| * 1. TWT GET |
| * 2. TWT TERMINATE |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_MIN_WAKE_INTVL: Optional (u32) |
| * Minimum tolerance limit of wake interval parameter in microseconds. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_MAX_WAKE_INTVL: Optional (u32) |
| * Maximum tolerance limit of wake interval parameter in microseconds. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_MIN_WAKE_DURATION: Optional (u32) |
| * Minimum tolerance limit of wake duration parameter in microseconds. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_MAX_WAKE_DURATION: Optional (u32) |
| * Maximum tolerance limit of wake duration parameter in microseconds. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_STATE: Optional (u32) |
| * TWT state for the given dialog id. The values for this are represented |
| * by enum qca_wlan_twt_setup_state. |
| * This is obtained through TWT GET operation. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL2_MANTISSA: Optional (u32) |
| * This attribute is used to configure wake interval mantissa. |
| * The unit is microseconds. This attribute, when specified, takes |
| * precedence over QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL_MANTISSA. |
| * This parameter is used for |
| * 1. TWT SET Request and Response |
| * 2. TWT GET Response |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_BCAST_ID: Optional (u8) |
| * This attribute is used to configure Broadcast TWT ID. |
| * The Broadcast TWT ID indicates a specific Broadcast TWT for which the |
| * transmitting STA is providing TWT parameters. The allowed values are 0 to 31. |
| * This parameter is used for |
| * 1. TWT SET Request |
| * 2. TWT TERMINATE Request |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_BCAST_RECOMMENDATION: Optional (u8) |
| * This attribute is used to configure Broadcast TWT recommendation. |
| * The Broadcast TWT Recommendation subfield contains a value that indicates |
| * recommendations on the types of frames that are transmitted by TWT |
| * scheduled STAs and scheduling AP during the broadcast TWT SP. |
| * The allowed values are 0 - 3. |
| * This parameter is used for |
| * 1. TWT SET Request |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_BCAST_PERSISTENCE: Optional (u8) |
| * This attribute is used to configure Broadcast TWT Persistence. |
| * The Broadcast TWT Persistence subfield indicates the number of |
| * TBTTs during which the Broadcast TWT SPs corresponding to this |
| * broadcast TWT Parameter set are present. The number of beacon intervals |
| * during which the Broadcast TWT SPs are present is equal to the value in the |
| * Broadcast TWT Persistence subfield plus 1 except that the value 255 |
| * indicates that the Broadcast TWT SPs are present until explicitly terminated. |
| * This parameter is used for |
| * 1. TWT SET Request |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_RESPONDER_PM_MODE: Optional (u8) |
| * This attribute contains the value of the Responder PM Mode subfield (0 or 1) |
| * from TWT response frame. |
| * This parameter is used for |
| * 1. TWT SET Response |
| * 2. TWT GET Response |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_ANNOUNCE_TIMEOUT: Optional (u32) |
| * This attribute is used to configure the announce timeout value (in us) in |
| * the firmware. This timeout value is only applicable for the announced TWT. If |
| * the timeout value is non-zero the firmware waits up to the timeout value to |
| * use Data frame as an announcement frame. If the timeout value is 0 the |
| * firmware sends an explicit QoS NULL frame as the announcement frame on SP |
| * start. The default value in the firmware is 0. |
| * This parameter is used for |
| * 1. TWT SET Request |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_PAD: Attribute used for padding for 64-bit |
| * alignment. |
| */ |
| enum qca_wlan_vendor_attr_twt_setup { |
| QCA_WLAN_VENDOR_ATTR_TWT_SETUP_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_TWT_SETUP_BCAST = 1, |
| QCA_WLAN_VENDOR_ATTR_TWT_SETUP_REQ_TYPE = 2, |
| QCA_WLAN_VENDOR_ATTR_TWT_SETUP_TRIGGER = 3, |
| QCA_WLAN_VENDOR_ATTR_TWT_SETUP_FLOW_TYPE = 4, |
| QCA_WLAN_VENDOR_ATTR_TWT_SETUP_FLOW_ID = 5, |
| QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL_EXP = 6, |
| QCA_WLAN_VENDOR_ATTR_TWT_SETUP_PROTECTION = 7, |
| QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_TIME = 8, |
| QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_DURATION = 9, |
| QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL_MANTISSA = 10, |
| |
| /* TWT Response only attributes */ |
| QCA_WLAN_VENDOR_ATTR_TWT_SETUP_STATUS = 11, |
| QCA_WLAN_VENDOR_ATTR_TWT_SETUP_RESP_TYPE = 12, |
| QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_TIME_TSF = 13, |
| QCA_WLAN_VENDOR_ATTR_TWT_SETUP_TWT_INFO_ENABLED = 14, |
| |
| QCA_WLAN_VENDOR_ATTR_TWT_SETUP_MAC_ADDR = 15, |
| QCA_WLAN_VENDOR_ATTR_TWT_SETUP_MIN_WAKE_INTVL = 16, |
| QCA_WLAN_VENDOR_ATTR_TWT_SETUP_MAX_WAKE_INTVL = 17, |
| QCA_WLAN_VENDOR_ATTR_TWT_SETUP_MIN_WAKE_DURATION = 18, |
| QCA_WLAN_VENDOR_ATTR_TWT_SETUP_MAX_WAKE_DURATION = 19, |
| QCA_WLAN_VENDOR_ATTR_TWT_SETUP_STATE = 20, |
| |
| QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL2_MANTISSA = 21, |
| |
| QCA_WLAN_VENDOR_ATTR_TWT_SETUP_BCAST_ID = 22, |
| QCA_WLAN_VENDOR_ATTR_TWT_SETUP_BCAST_RECOMMENDATION = 23, |
| QCA_WLAN_VENDOR_ATTR_TWT_SETUP_BCAST_PERSISTENCE = 24, |
| |
| QCA_WLAN_VENDOR_ATTR_TWT_SETUP_RESPONDER_PM_MODE = 25, |
| QCA_WLAN_VENDOR_ATTR_TWT_SETUP_ANNOUNCE_TIMEOUT = 26, |
| |
| QCA_WLAN_VENDOR_ATTR_TWT_SETUP_PAD = 27, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_TWT_SETUP_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_TWT_SETUP_MAX = |
| QCA_WLAN_VENDOR_ATTR_TWT_SETUP_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_twt_status - Represents the status of the requested |
| * TWT operation |
| * |
| * @QCA_WLAN_VENDOR_TWT_STATUS_OK: TWT request successfully completed |
| * @QCA_WLAN_VENDOR_TWT_STATUS_TWT_NOT_ENABLED: TWT not enabled |
| * @QCA_WLAN_VENDOR_TWT_STATUS_USED_DIALOG_ID: TWT dialog ID is already used |
| * @QCA_WLAN_VENDOR_TWT_STATUS_SESSION_BUSY: TWT session is busy |
| * @QCA_WLAN_VENDOR_TWT_STATUS_SESSION_NOT_EXIST: TWT session does not exist |
| * @QCA_WLAN_VENDOR_TWT_STATUS_NOT_SUSPENDED: TWT session not in suspend state |
| * @QCA_WLAN_VENDOR_TWT_STATUS_INVALID_PARAM: Invalid parameters |
| * @QCA_WLAN_VENDOR_TWT_STATUS_NOT_READY: FW not ready |
| * @QCA_WLAN_VENDOR_TWT_STATUS_NO_RESOURCE: FW resource exhausted |
| * @QCA_WLAN_VENDOR_TWT_STATUS_NO_ACK: Peer AP/STA did not ACK the |
| * request/response frame |
| * @QCA_WLAN_VENDOR_TWT_STATUS_NO_RESPONSE: Peer AP did not send the response |
| * frame |
| * @QCA_WLAN_VENDOR_TWT_STATUS_DENIED: AP did not accept the request |
| * @QCA_WLAN_VENDOR_TWT_STATUS_UNKNOWN_ERROR: Adding TWT dialog failed due to an |
| * unknown reason |
| * @QCA_WLAN_VENDOR_TWT_STATUS_ALREADY_SUSPENDED: TWT session already in |
| * suspend state |
| * @QCA_WLAN_VENDOR_TWT_STATUS_IE_INVALID: FW has dropped the frame due to |
| * invalid IE in the received TWT frame |
| * @QCA_WLAN_VENDOR_TWT_STATUS_PARAMS_NOT_IN_RANGE: Parameters received from |
| * the responder are not in the specified range |
| * @QCA_WLAN_VENDOR_TWT_STATUS_PEER_INITIATED_TERMINATE: FW terminated the TWT |
| * session due to request from the responder. Used on the TWT_TERMINATE |
| * notification from the firmware. |
| * @QCA_WLAN_VENDOR_TWT_STATUS_ROAM_INITIATED_TERMINATE: FW terminated the TWT |
| * session due to roaming. Used on the TWT_TERMINATE notification from the |
| * firmware. |
| * @QCA_WLAN_VENDOR_TWT_STATUS_SCC_MCC_CONCURRENCY_TERMINATE: FW terminated the |
| * TWT session due to SCC (Single Channel Concurrency) and MCC (Multi Channel |
| * Concurrency). Used on the TWT_TERMINATE notification from the firmware. |
| * @QCA_WLAN_VENDOR_TWT_STATUS_ROAMING_IN_PROGRESS: FW rejected the TWT setup |
| * request due to roaming in progress. |
| * @QCA_WLAN_VENDOR_TWT_STATUS_CHANNEL_SWITCH_IN_PROGRESS: FW rejected the TWT |
| * setup request due to channel switch in progress. |
| * @QCA_WLAN_VENDOR_TWT_STATUS_SCAN_IN_PROGRESS: FW rejected the TWT setup |
| * request due to scan in progress. |
| * QCA_WLAN_VENDOR_TWT_STATUS_POWER_SAVE_EXIT_TERMINATE: The driver requested to |
| * terminate an existing TWT session on power save exit request from userspace. |
| * Used on the TWT_TERMINATE notification from the driver/firmware. |
| * @QCA_WLAN_VENDOR_TWT_STATUS_TWT_REQUIRED: The peer has set the TWT |
| * required bit in its capabilities. |
| * @QCA_WLAN_VENDOR_TWT_STATUS_TWT_NOT_REQUIRED: The peer has cleared |
| * the TWT required bit(1->0) in its capabilities. |
| */ |
| enum qca_wlan_vendor_twt_status { |
| QCA_WLAN_VENDOR_TWT_STATUS_OK = 0, |
| QCA_WLAN_VENDOR_TWT_STATUS_TWT_NOT_ENABLED = 1, |
| QCA_WLAN_VENDOR_TWT_STATUS_USED_DIALOG_ID = 2, |
| QCA_WLAN_VENDOR_TWT_STATUS_SESSION_BUSY = 3, |
| QCA_WLAN_VENDOR_TWT_STATUS_SESSION_NOT_EXIST = 4, |
| QCA_WLAN_VENDOR_TWT_STATUS_NOT_SUSPENDED = 5, |
| QCA_WLAN_VENDOR_TWT_STATUS_INVALID_PARAM = 6, |
| QCA_WLAN_VENDOR_TWT_STATUS_NOT_READY = 7, |
| QCA_WLAN_VENDOR_TWT_STATUS_NO_RESOURCE = 8, |
| QCA_WLAN_VENDOR_TWT_STATUS_NO_ACK = 9, |
| QCA_WLAN_VENDOR_TWT_STATUS_NO_RESPONSE = 10, |
| QCA_WLAN_VENDOR_TWT_STATUS_DENIED = 11, |
| QCA_WLAN_VENDOR_TWT_STATUS_UNKNOWN_ERROR = 12, |
| QCA_WLAN_VENDOR_TWT_STATUS_ALREADY_SUSPENDED = 13, |
| QCA_WLAN_VENDOR_TWT_STATUS_IE_INVALID = 14, |
| QCA_WLAN_VENDOR_TWT_STATUS_PARAMS_NOT_IN_RANGE = 15, |
| QCA_WLAN_VENDOR_TWT_STATUS_PEER_INITIATED_TERMINATE = 16, |
| QCA_WLAN_VENDOR_TWT_STATUS_ROAM_INITIATED_TERMINATE = 17, |
| QCA_WLAN_VENDOR_TWT_STATUS_SCC_MCC_CONCURRENCY_TERMINATE = 18, |
| QCA_WLAN_VENDOR_TWT_STATUS_ROAMING_IN_PROGRESS = 19, |
| QCA_WLAN_VENDOR_TWT_STATUS_CHANNEL_SWITCH_IN_PROGRESS = 20, |
| QCA_WLAN_VENDOR_TWT_STATUS_SCAN_IN_PROGRESS = 21, |
| QCA_WLAN_VENDOR_TWT_STATUS_POWER_SAVE_EXIT_TERMINATE = 22, |
| QCA_WLAN_VENDOR_TWT_STATUS_TWT_REQUIRED = 23, |
| QCA_WLAN_VENDOR_TWT_STATUS_TWT_NOT_REQUIRED = 24, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_twt_resume - Represents attributes for |
| * TWT (Target Wake Time) resume request. These attributes are sent as part of |
| * %QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_RESUME and |
| * %QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION. Also used by |
| * attributes through %QCA_NL80211_VENDOR_SUBCMD_CONFIG_TWT. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT_TWT: Optional (u8) |
| * @QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT2_TWT: Optional (u32) |
| * These attributes are used as the SP offset which is the offset from TSF after |
| * which the wake happens. The units are in microseconds. Please note that |
| * _NEXT_TWT is limited to u8 whereas _NEXT2_TWT takes the u32 data. |
| * _NEXT2_TWT takes the precedence over _NEXT_TWT and thus the recommendation |
| * is to use _NEXT2_TWT. If neither of these attributes is provided, the value |
| * will be set to zero. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT_TWT_SIZE: Required (u32) |
| * This attribute represents the next TWT subfield size. |
| * Value 0 represents 0 bits, 1 represents 32 bits, 2 for 48 bits, |
| * and 4 for 64 bits. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_RESUME_FLOW_ID: Required (u8). |
| * Flow ID is the unique identifier for each TWT session. This attribute |
| * represents the respective TWT session to resume. |
| * Flow ID values from 0 to 254 represent a single TWT session |
| * Flow ID value of 255 represents all TWT sessions. |
| * If an invalid dialog id is provided, status |
| * QCA_WLAN_VENDOR_TWT_STATUS_SESSION_NOT_EXIST will be returned. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_RESUME_MAC_ADDR: 6-byte MAC address |
| * Represents the MAC address of the peer to which TWT Resume is |
| * being sent. This is used in AP mode to represent the respective |
| * client and is a required parameter. In STA mode, this is an optional |
| * parameter |
| */ |
| enum qca_wlan_vendor_attr_twt_resume { |
| QCA_WLAN_VENDOR_ATTR_TWT_RESUME_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT_TWT = 1, |
| QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT_TWT_SIZE = 2, |
| QCA_WLAN_VENDOR_ATTR_TWT_RESUME_FLOW_ID = 3, |
| QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT2_TWT = 4, |
| QCA_WLAN_VENDOR_ATTR_TWT_RESUME_MAC_ADDR = 5, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_TWT_RESUME_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_TWT_RESUME_MAX = |
| QCA_WLAN_VENDOR_ATTR_TWT_RESUME_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_twt_nudge - Represents attributes for |
| * TWT (Target Wake Time) nudge request. TWT nudge is a combination of suspend |
| * and resume in a single request. These attributes are sent as part of |
| * %QCA_NL80211_VENDOR_SUBCMD_CONFIG_TWT. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_FLOW_ID: Required (u8) |
| * Flow ID is the unique identifier for each TWT session. This attribute |
| * represents the respective TWT session to suspend and resume. |
| * Flow ID values from 0 to 254 represent a single TWT session |
| * Flow ID value of 255 represents all TWT sessions in TWT NUDGE request |
| * and response. |
| * If an invalid dialog id is provided, status |
| * QCA_WLAN_VENDOR_TWT_STATUS_SESSION_NOT_EXIST will be returned. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_WAKE_TIME: Required (u32) |
| * This attribute is used as the SP offset which is the offset from |
| * TSF after which the wake happens. The units are in microseconds. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_NEXT_TWT_SIZE: Required (u32) |
| * This attribute represents the next TWT subfield size. |
| * Value 0 represents 0 bits, 1 represents 32 bits, 2 for 48 bits, |
| * and 4 for 64 bits. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_MAC_ADDR: 6-byte MAC address |
| * Represents the MAC address of the peer to which TWT Suspend and Resume is |
| * being sent. This is used in AP mode to represent the respective |
| * client and is a required parameter. In STA mode, this is an optional |
| * parameter. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_WAKE_TIME_TSF: Optional (u64) |
| * This field contains absolute TSF value of the time at which the TWT |
| * session will be resumed. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_SP_START_OFFSET: Optional (s32) |
| * This field will be used when device supports Flexible TWT. |
| * This field contains an offset value by which to shift the starting time |
| * of the next service period. The value of offset can be negative or positive. |
| * If provided, this attribute will override |
| * QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_WAKE_TIME. The units are in microseconds. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_PAD: Attribute used for padding for 64-bit |
| * alignment. |
| */ |
| enum qca_wlan_vendor_attr_twt_nudge { |
| QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_FLOW_ID = 1, |
| QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_WAKE_TIME = 2, |
| QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_NEXT_TWT_SIZE = 3, |
| QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_MAC_ADDR = 4, |
| QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_WAKE_TIME_TSF = 5, |
| QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_SP_START_OFFSET = 6, |
| QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_PAD = 7, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_MAX = |
| QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_twt_stats: Represents attributes for |
| * TWT (Target Wake Time) get statistics and clear statistics request. |
| * These attributes are sent as part of |
| * %QCA_NL80211_VENDOR_SUBCMD_CONFIG_TWT. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_STATS_FLOW_ID: Required (u8) |
| * Flow ID is the unique identifier for each TWT session. This attribute |
| * represents the respective TWT session for get and clear TWT statistics. |
| * Flow ID values from 0 to 254 represent a single TWT session |
| * Flow ID value of 255 represents all TWT sessions in |
| * 1) TWT GET STATISTICS request and response |
| * 2) TWT CLEAR STATISTICS request |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_STATS_MAC_ADDR: 6-byte MAC address |
| * Represents the MAC address of the peer for which TWT Statistics |
| * is required. |
| * In AP mode this is used to represent the respective |
| * client and is a required parameter for |
| * 1) TWT GET STATISTICS request and response |
| * 2) TWT CLEAR STATISTICS request and response |
| * In STA mode, this is an optional parameter. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_STATS_SESSION_WAKE_DURATION: Required (u32) |
| * This is the duration of the service period in microseconds. |
| * Obtained in the QCA_WLAN_TWT_GET_STATS response from the firmware. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_STATS_AVG_WAKE_DURATION: Required (u32) |
| * Average of the actual wake duration observed so far. Unit is microseconds. |
| * Obtained in the QCA_WLAN_TWT_GET_STATS response from the firmware. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_STATS_NUM_SP_ITERATIONS: Required (u32) |
| * The number of TWT service periods elapsed so far. |
| * Obtained in the QCA_WLAN_TWT_GET_STATS response from the firmware. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_STATS_MIN_WAKE_DURATION: Required (u32) |
| * This is the minimum value of the wake duration observed across |
| * QCA_WLAN_VENDOR_ATTR_TWT_STATS_NUM_SP_ITERATIONS. Unit is |
| * microseconds. |
| * Obtained in the QCA_WLAN_TWT_GET_STATS response from the firmware. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_STATS_MAX_WAKE_DURATION: Required (u32) |
| * This is the maximum value of wake duration observed across |
| * QCA_WLAN_VENDOR_ATTR_TWT_STATS_NUM_SP_ITERATIONS. Unit is |
| * microseconds. |
| * Obtained in the QCA_WLAN_TWT_GET_STATS response from the firmware. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_STATS_AVERAGE_TX_MPDU: Required (u32) |
| * Average number of MPDUs transmitted successfully across |
| * QCA_WLAN_VENDOR_ATTR_TWT_STATS_NUM_SP_ITERATIONS. |
| * Obtained in the QCA_WLAN_TWT_GET_STATS response from the firmware. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_STATS_AVERAGE_RX_MPDU: Required (u32) |
| * Average number of MPDUs received successfully across |
| * QCA_WLAN_VENDOR_ATTR_TWT_STATS_NUM_SP_ITERATIONS. |
| * Obtained in the QCA_WLAN_TWT_GET_STATS response from the firmware. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_STATS_AVERAGE_TX_PACKET_SIZE: Required (u32) |
| * Average number of bytes transmitted successfully across |
| * QCA_WLAN_VENDOR_ATTR_TWT_STATS_NUM_SP_ITERATIONS. |
| * Obtained in the QCA_WLAN_TWT_GET_STATS response from the firmware. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_STATS_AVERAGE_RX_PACKET_SIZE: Required (u32) |
| * Average number of bytes received successfully across |
| * QCA_WLAN_VENDOR_ATTR_TWT_STATS_NUM_SP_ITERATIONS. |
| * Obtained in the QCA_WLAN_TWT_GET_STATS response from the firmware. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_STATS_STATUS: Required (u32) |
| * Status of the TWT GET STATISTICS request. |
| * This contains status values in enum qca_wlan_vendor_twt_status |
| * Obtained in the QCA_WLAN_TWT_GET_STATS response from the firmware. |
| */ |
| enum qca_wlan_vendor_attr_twt_stats { |
| QCA_WLAN_VENDOR_ATTR_TWT_STATS_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_TWT_STATS_FLOW_ID = 1, |
| QCA_WLAN_VENDOR_ATTR_TWT_STATS_MAC_ADDR = 2, |
| QCA_WLAN_VENDOR_ATTR_TWT_STATS_SESSION_WAKE_DURATION = 3, |
| QCA_WLAN_VENDOR_ATTR_TWT_STATS_AVG_WAKE_DURATION = 4, |
| QCA_WLAN_VENDOR_ATTR_TWT_STATS_NUM_SP_ITERATIONS = 5, |
| QCA_WLAN_VENDOR_ATTR_TWT_STATS_MIN_WAKE_DURATION = 6, |
| QCA_WLAN_VENDOR_ATTR_TWT_STATS_MAX_WAKE_DURATION = 7, |
| QCA_WLAN_VENDOR_ATTR_TWT_STATS_AVERAGE_TX_MPDU = 8, |
| QCA_WLAN_VENDOR_ATTR_TWT_STATS_AVERAGE_RX_MPDU = 9, |
| QCA_WLAN_VENDOR_ATTR_TWT_STATS_AVERAGE_TX_PACKET_SIZE = 10, |
| QCA_WLAN_VENDOR_ATTR_TWT_STATS_AVERAGE_RX_PACKET_SIZE = 11, |
| QCA_WLAN_VENDOR_ATTR_TWT_STATS_STATUS = 12, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_TWT_STATS_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_TWT_STATS_MAX = |
| QCA_WLAN_VENDOR_ATTR_TWT_STATS_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * qca_wlan_twt_get_capa - Represents the bitmap of TWT capabilities |
| * supported by the device and the peer. |
| * Values for %QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_GET_CAPABILITIES |
| * |
| * @QCA_WLAN_TWT_CAPA_REQUESTOR: TWT requestor support is advertised by |
| * TWT non-scheduling STA. This capability is advertised in the HE |
| * Capability/Extended Capabilities information element in the |
| * Association Request frame by the device. |
| * |
| * @QCA_WLAN_TWT_CAPA_RESPONDER: TWT responder support is advertised by |
| * the TWT scheduling AP. This capability is advertised in the Extended |
| * Capabilities/HE Capabilities information element. |
| * |
| * @QCA_WLAN_TWT_CAPA_BROADCAST: On the requestor side, this indicates support |
| * for the broadcast TWT functionality. On the responder side, this indicates |
| * support for the role of broadcast TWT scheduling functionality. This |
| * capability is advertised in the HE Capabilities information element. |
| * |
| * @QCA_WLAN_TWT_CAPA_TWT_FLEXIBLE: The device supports flexible TWT schedule. |
| * This capability is advertised in the HE Capabilities information element. |
| * |
| * @QCA_WLAN_TWT_CAPA_REQUIRED: The TWT Required is advertised by AP to indicate |
| * that it mandates the associated HE STAs to support TWT. This capability is |
| * advertised by AP in the HE Operation Parameters field of the HE Operation |
| * information element. |
| */ |
| enum qca_wlan_twt_capa { |
| QCA_WLAN_TWT_CAPA_REQUESTOR = BIT(0), |
| QCA_WLAN_TWT_CAPA_RESPONDER = BIT(1), |
| QCA_WLAN_TWT_CAPA_BROADCAST = BIT(2), |
| QCA_WLAN_TWT_CAPA_FLEXIBLE = BIT(3), |
| QCA_WLAN_TWT_CAPA_REQUIRED = BIT(4), |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_twt_capability - Represents attributes for TWT |
| * get capabilities request type. Used by QCA_WLAN_TWT_GET_CAPABILITIES TWT |
| * operation. |
| * @QCA_WLAN_VENDOR_ATTR_TWT_CAPABILITIES_MAC_ADDR: 6-byte MAC address |
| * Represents the MAC address of the peer for which the TWT capabilities |
| * are being queried. This is used in AP mode to represent the respective |
| * client. In STA mode, this is an optional parameter. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_CAPABILITIES_SELF: (u16). |
| * Self TWT capabilities. Carries a bitmap of TWT capabilities specified in |
| * enum qca_wlan_twt_capa. |
| * @QCA_WLAN_VENDOR_ATTR_TWT_CAPABILITIES_PEER: (u16). |
| * Peer TWT capabilities. Carries a bitmap of TWT capabilities specified in |
| * enum qca_wlan_twt_capa. |
| */ |
| enum qca_wlan_vendor_attr_twt_capability { |
| QCA_WLAN_VENDOR_ATTR_TWT_CAPABILITIES_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_TWT_CAPABILITIES_MAC_ADDR = 1, |
| QCA_WLAN_VENDOR_ATTR_TWT_CAPABILITIES_SELF = 2, |
| QCA_WLAN_VENDOR_ATTR_TWT_CAPABILITIES_PEER = 3, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_TWT_CAPABILITIES_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_TWT_CAPABILITIES_MAX = |
| QCA_WLAN_VENDOR_ATTR_TWT_CAPABILITIES_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_twt_set_param: Represents attributes for |
| * TWT (Target Wake Time) related parameters. It is used when |
| * %QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_OPERATION is set to %QCA_WLAN_TWT_SET_PARAM. |
| * These attributes are sent as part of %QCA_NL80211_VENDOR_SUBCMD_CONFIG_TWT. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_SET_PARAM_AP_AC_VALUE: Optional (u8) |
| * This attribute configures AC parameters to be used for all TWT |
| * sessions in AP mode. |
| * Uses the enum qca_wlan_ac_type values. |
| */ |
| enum qca_wlan_vendor_attr_twt_set_param { |
| QCA_WLAN_VENDOR_ATTR_TWT_SET_PARAM_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_TWT_SET_PARAM_AP_AC_VALUE = 1, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_TWT_SET_PARAM_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_TWT_SET_PARAM_MAX = |
| QCA_WLAN_VENDOR_ATTR_TWT_SET_PARAM_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_twt_setup_resp_type - Represents the response type by |
| * the TWT responder |
| * |
| * @QCA_WLAN_VENDOR_TWT_RESP_ALTERNATE: TWT responder suggests TWT |
| * parameters that are different from TWT requesting STA suggested |
| * or demanded TWT parameters |
| * @QCA_WLAN_VENDOR_TWT_RESP_DICTATE: TWT responder demands TWT |
| * parameters that are different from TWT requesting STA TWT suggested |
| * or demanded parameters |
| * @QCA_WLAN_VENDOR_TWT_RESP_REJECT: TWT responder rejects TWT |
| * setup |
| * @QCA_WLAN_VENDOR_TWT_RESP_ACCEPT: TWT responder accepts the TWT |
| * setup. |
| */ |
| enum qca_wlan_vendor_twt_setup_resp_type { |
| QCA_WLAN_VENDOR_TWT_RESP_ALTERNATE = 1, |
| QCA_WLAN_VENDOR_TWT_RESP_DICTATE = 2, |
| QCA_WLAN_VENDOR_TWT_RESP_REJECT = 3, |
| QCA_WLAN_VENDOR_TWT_RESP_ACCEPT = 4, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_twt_setup_req_type - Required (u8) |
| * Represents the setup type being requested for TWT. |
| * @QCA_WLAN_VENDOR_TWT_SETUP_REQUEST: STA is not specifying all the TWT |
| * parameters but relying on AP to fill the parameters during the negotiation. |
| * @QCA_WLAN_VENDOR_TWT_SETUP_SUGGEST: STA will provide all the suggested |
| * values which the AP may accept or AP may provide alternative parameters |
| * which the STA may accept. |
| * @QCA_WLAN_VENDOR_TWT_SETUP_DEMAND: STA is not willing to accept any |
| * alternate parameters than the requested ones. |
| */ |
| enum qca_wlan_vendor_twt_setup_req_type { |
| QCA_WLAN_VENDOR_TWT_SETUP_REQUEST = 1, |
| QCA_WLAN_VENDOR_TWT_SETUP_SUGGEST = 2, |
| QCA_WLAN_VENDOR_TWT_SETUP_DEMAND = 3, |
| }; |
| |
| /** |
| * enum qca_wlan_roam_scan_event_type - Type of roam scan event |
| * |
| * Indicates the type of roam scan event sent by firmware/driver. |
| * |
| * @QCA_WLAN_ROAM_SCAN_TRIGGER_EVENT: Roam scan trigger event type. |
| * @QCA_WLAN_ROAM_SCAN_STOP_EVENT: Roam scan stopped event type. |
| */ |
| enum qca_wlan_roam_scan_event_type { |
| QCA_WLAN_ROAM_SCAN_TRIGGER_EVENT = 0, |
| QCA_WLAN_ROAM_SCAN_STOP_EVENT = 1, |
| }; |
| |
| /** |
| * enum qca_wlan_roam_scan_trigger_reason - Roam scan trigger reason |
| * |
| * Indicates the reason for triggering roam scan by firmware/driver. |
| * |
| * @QCA_WLAN_ROAM_SCAN_TRIGGER_REASON_LOW_RSSI: Due to low RSSI of current AP. |
| * @QCA_WLAN_ROAM_SCAN_TRIGGER_REASON_HIGH_PER: Due to high packet error rate. |
| */ |
| enum qca_wlan_roam_scan_trigger_reason { |
| QCA_WLAN_ROAM_SCAN_TRIGGER_REASON_LOW_RSSI = 0, |
| QCA_WLAN_ROAM_SCAN_TRIGGER_REASON_HIGH_PER = 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_roam_scan - Vendor subcmd attributes to report |
| * roam scan related details from driver/firmware to user space. enum values |
| * are used for NL attributes sent with |
| * %QCA_NL80211_VENDOR_SUBCMD_ROAM_SCAN_EVENT sub command. |
| */ |
| enum qca_wlan_vendor_attr_roam_scan { |
| QCA_WLAN_VENDOR_ATTR_ROAM_SCAN_INVALID = 0, |
| /* Encapsulates type of roam scan event being reported. enum |
| * qca_wlan_roam_scan_event_type describes the possible range of |
| * values. u32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_SCAN_EVENT_TYPE = 1, |
| /* Encapsulates reason for triggering roam scan. enum |
| * qca_wlan_roam_scan_trigger_reason describes the possible range of |
| * values. u32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_SCAN_TRIGGER_REASON = 2, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_SCAN_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_ROAM_SCAN_MAX = |
| QCA_WLAN_VENDOR_ATTR_ROAM_SCAN_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_cfr_data_transport_modes - Defines QCA vendor CFR data |
| * transport modes and is used by the attribute |
| * QCA_WLAN_VENDOR_ATTR_PEER_CFR_DATA_TRANSPORT_MODE as a part of the vendor |
| * command QCA_NL80211_VENDOR_SUBCMD_PEER_CFR_CAPTURE_CFG. |
| * @QCA_WLAN_VENDOR_CFR_DATA_RELAY_FS: Use relayfs to send CFR data. |
| * @QCA_WLAN_VENDOR_CFR_DATA_NETLINK_EVENTS: Use netlink events to send CFR |
| * data. The data shall be encapsulated within |
| * QCA_WLAN_VENDOR_ATTR_PEER_CFR_RESP_DATA along with the vendor sub command |
| * QCA_NL80211_VENDOR_SUBCMD_PEER_CFR_CAPTURE_CFG as an asynchronous event. |
| */ |
| enum qca_wlan_vendor_cfr_data_transport_modes { |
| QCA_WLAN_VENDOR_CFR_DATA_RELAY_FS = 0, |
| QCA_WLAN_VENDOR_CFR_DATA_NETLINK_EVENTS = 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_cfr_method - QCA vendor CFR methods used by |
| * attribute QCA_WLAN_VENDOR_ATTR_PEER_CFR_METHOD as part of vendor |
| * command QCA_NL80211_VENDOR_SUBCMD_PEER_CFR_CAPTURE_CFG. |
| * @QCA_WLAN_VENDOR_CFR_METHOD_QOS_NULL: CFR method using QoS Null frame |
| * @QCA_WLAN_VENDOR_CFR_QOS_NULL_WITH_PHASE: CFR method using QoS Null frame |
| * with phase |
| * @QCA_WLAN_VENDOR_CFR_PROBE_RESPONSE: CFR method using Probe Response frame |
| */ |
| enum qca_wlan_vendor_cfr_method { |
| QCA_WLAN_VENDOR_CFR_METHOD_QOS_NULL = 0, |
| QCA_WLAN_VENDOR_CFR_QOS_NULL_WITH_PHASE = 1, |
| QCA_WLAN_VENDOR_CFR_PROBE_RESPONSE = 2, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_cfr_capture_type - QCA vendor CFR capture type used by |
| * attribute QCA_WLAN_VENDOR_ATTR_PEER_CFR_CAPTURE_TYPE. |
| * @QCA_WLAN_VENDOR_CFR_DIRECT_FTM: Filter directed FTM ACK frames. |
| * @QCA_WLAN_VENDOR_CFR_ALL_FTM_ACK: Filter all FTM ACK frames. |
| * @QCA_WLAN_VENDOR_CFR_DIRECT_NDPA_NDP: Filter NDPA NDP directed frames. |
| * @QCA_WLAN_VENDOR_CFR_TA_RA: Filter frames based on TA/RA/Subtype which |
| * is provided by one or more of below attributes: |
| * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_TA |
| * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_RA |
| * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_TA_MASK |
| * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_RA_MASK |
| * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_MGMT_FILTER |
| * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_CTRL_FILTER |
| * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_DATA_FILTER |
| * @QCA_WLAN_CFR_ALL_PACKET: Filter all packets. |
| * @QCA_WLAN_VENDOR_CFR_NDPA_NDP_ALL: Filter all NDPA NDP frames. |
| */ |
| enum qca_wlan_vendor_cfr_capture_type { |
| QCA_WLAN_VENDOR_CFR_DIRECT_FTM = 0, |
| QCA_WLAN_VENDOR_CFR_ALL_FTM_ACK = 1, |
| QCA_WLAN_VENDOR_CFR_DIRECT_NDPA_NDP = 2, |
| QCA_WLAN_VENDOR_CFR_TA_RA = 3, |
| QCA_WLAN_VENDOR_CFR_ALL_PACKET = 4, |
| QCA_WLAN_VENDOR_CFR_NDPA_NDP_ALL = 5, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_peer_cfr_capture_attr - Used by the vendor command |
| * QCA_NL80211_VENDOR_SUBCMD_PEER_CFR_CAPTURE_CFG to configure peer |
| * Channel Frequency Response capture parameters and enable periodic CFR |
| * capture. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_CFR_PEER_MAC_ADDR: Optional (6-byte MAC address) |
| * MAC address of peer. This is for CFR version 1 only. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_ENABLE: Required (flag) |
| * Enable peer CFR capture. This attribute is mandatory to enable peer CFR |
| * capture. If this attribute is not present, peer CFR capture is disabled. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_BANDWIDTH: Optional (u8) |
| * BW of measurement, attribute uses the values in enum nl80211_chan_width |
| * Supported values: 20, 40, 80, 80+80, 160. |
| * Note that all targets may not support all bandwidths. |
| * This attribute is mandatory for version 1 if attribute |
| * QCA_WLAN_VENDOR_ATTR_PEER_CFR_ENABLE is used. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_PERIODICITY: Optional (u32) |
| * Periodicity of CFR measurement in milliseconds. |
| * Periodicity should be a multiple of Base timer. |
| * Current Base timer value supported is 10 milliseconds (default). |
| * 0 for one shot capture. |
| * This attribute is mandatory for version 1 if attribute |
| * QCA_WLAN_VENDOR_ATTR_PEER_CFR_ENABLE is used. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_METHOD: Optional (u8) |
| * Method used to capture Channel Frequency Response. |
| * Attribute uses the values defined in enum qca_wlan_vendor_cfr_method. |
| * This attribute is mandatory for version 1 if attribute |
| * QCA_WLAN_VENDOR_ATTR_PEER_CFR_ENABLE is used. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_PERIODIC_CFR_CAPTURE_ENABLE: Optional (flag) |
| * Enable periodic CFR capture. |
| * This attribute is mandatory for version 1 to enable Periodic CFR capture. |
| * If this attribute is not present, periodic CFR capture is disabled. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_VERSION: Optional (u8) |
| * Value is 1 or 2 since there are two versions of CFR capture. Two versions |
| * can't be enabled at same time. This attribute is mandatory if target |
| * support both versions and use one of them. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_ENABLE_GROUP_BITMAP: Optional (u32) |
| * This attribute is mandatory for version 2 if |
| * QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_ENTRY is used. |
| * Bits 15:0 bitfield indicates which group is to be enabled. |
| * Bits 31:16 Reserved for future use. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_DURATION: Optional (u32) |
| * CFR capture duration in microsecond. This attribute is mandatory for |
| * version 2 if attribute QCA_WLAN_VENDOR_ATTR_PEER_CFR_INTERVAL is used. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_INTERVAL: Optional (u32) |
| * CFR capture interval in microsecond. This attribute is mandatory for |
| * version 2 if attribute QCA_WLAN_VENDOR_ATTR_PEER_CFR_DURATION is used. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_CAPTURE_TYPE: Optional (u32) |
| * CFR capture type is defined in enum qca_wlan_vendor_cfr_capture_type. |
| * This attribute is mandatory for version 2. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_UL_MU_MASK: Optional (u64) |
| * Bitfield indicating which user in the current UL MU transmissions are |
| * enabled for CFR capture. Bits 36 to 0 indicate user indexes for 37 users in |
| * a UL MU transmission. If bit 0 is set, the CFR capture will happen for user |
| * index 0 in the current UL MU transmission. If bits 0 and 2 are set, CFR |
| * capture for UL MU TX corresponds to user indices 0 and 2. Bits 63:37 are |
| * reserved for future use. This is for CFR version 2 only. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_FREEZE_TLV_DELAY_COUNT: Optional (u32) |
| * Indicates the number of consecutive RX frames to be skipped before CFR |
| * capture is enabled again. This is for CFR version 2 only. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_TABLE: Nested attribute containing |
| * one or more %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_ENTRY attributes. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_ENTRY: Nested attribute containing |
| * the following group attributes: |
| * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_NUMBER, |
| * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_TA, |
| * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_RA, |
| * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_TA_MASK, |
| * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_RA_MASK, |
| * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_NSS, |
| * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_BW, |
| * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_MGMT_FILTER, |
| * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_CTRL_FILTER, |
| * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_DATA_FILTER |
| * |
| * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_NUMBER: Optional (u32) |
| * Target supports multiple groups for some configurations. The group number |
| * can be any value between 0 and 15. This is for CFR version 2 only. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_TA: Optional (6-byte MAC address) |
| * Transmitter address which is used to filter frames. This MAC address takes |
| * effect with QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_TA_MASK. This is for CFR |
| * version 2 only. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_RA: Optional (6-byte MAC address) |
| * Receiver address which is used to filter frames. This MAC address takes |
| * effect with QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_RA_MASK. This is for CFR |
| * version 2 only. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_TA_MASK: Optional (6-byte MAC address) |
| * Mask of transmitter address which is used to filter frames. This is for CFR |
| * version 2 only. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_RA_MASK: Optional (6-byte MAC address) |
| * Mask of receiver address which is used to filter frames. This is for CFR |
| * version 2 only. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_NSS: Optional (u32) |
| * Indicates frames with a specific NSS will be filtered for CFR capture. |
| * This is for CFR version 2 only. This is a bitmask. Bits 7:0 request CFR |
| * capture to be done for frames matching the NSS specified within this bitmask. |
| * Bits 31:8 are reserved for future use. Bits 7:0 map to NSS: |
| * bit 0 : NSS 1 |
| * bit 1 : NSS 2 |
| * ... |
| * bit 7 : NSS 8 |
| * |
| * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_BW: Optional (u32) |
| * Indicates frames with a specific bandwidth will be filtered for CFR capture. |
| * This is for CFR version 2 only. This is a bitmask. Bits 4:0 request CFR |
| * capture to be done for frames matching the bandwidths specified within this |
| * bitmask. Bits 31:5 are reserved for future use. Bits 4:0 map to bandwidth |
| * numerated in enum nl80211_band (although not all bands may be supported |
| * by a given device). |
| * |
| * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_MGMT_FILTER: Optional (u32) |
| * Management frames matching the subtype filter categories will be filtered in |
| * by MAC for CFR capture. This is a bitmask in which each bit represents the |
| * corresponding Management frame subtype value per IEEE Std 802.11-2016, |
| * 9.2.4.1.3 Type and Subtype subfields. For example, Beacon frame control type |
| * is 8 and its value is 1 << 8 = 0x100. This is for CFR version 2 only. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_CTRL_FILTER: Optional (u32) |
| * Control frames matching the subtype filter categories will be filtered in by |
| * MAC for CFR capture. This is a bitmask in which each bit represents the |
| * corresponding Control frame subtype value per IEEE Std 802.11-2016, |
| * 9.2.4.1.3 Type and Subtype subfields. This is for CFR version 2 only. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_DATA_FILTER: Optional (u32) |
| * Data frames matching the subtype filter categories will be filtered in by |
| * MAC for CFR capture. This is a bitmask in which each bit represents the |
| * corresponding Data frame subtype value per IEEE Std 802.11-2016, |
| * 9.2.4.1.3 Type and Subtype subfields. This is for CFR version 2 only. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_DATA_TRANSPORT_MODE: Optional (u8) |
| * Userspace can use this attribute to specify the driver about which transport |
| * mode shall be used by the driver to send CFR data to userspace. Uses values |
| * from enum qca_wlan_vendor_cfr_data_transport_modes. When this attribute is |
| * not present, the driver shall use the default transport mechanism which is |
| * QCA_WLAN_VENDOR_CFR_DATA_RELAY_FS. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_DATA_RECEIVER_PID: Optional (u32) |
| * Userspace can use this attribute to specify the nl port id of the application |
| * which receives the CFR data and processes it further so that the drivers can |
| * unicast the netlink events to a specific application. Optionally included |
| * when QCA_WLAN_VENDOR_ATTR_PEER_CFR_DATA_TRANSPORT_MODE is set to |
| * QCA_WLAN_VENDOR_CFR_DATA_NETLINK_EVENTS, not required otherwise. The drivers |
| * shall multicast the netlink events when this attribute is not included. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_RESP_DATA: Required (NLA_BINARY). |
| * This attribute will be used by the driver to encapsulate and send CFR data |
| * to userspace along with QCA_NL80211_VENDOR_SUBCMD_PEER_CFR_CAPTURE_CFG as an |
| * asynchronous event when the driver is configured to send CFR data using |
| * netlink events with %QCA_WLAN_VENDOR_CFR_DATA_NETLINK_EVENTS. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_PAD: Attribute used for padding for 64-bit |
| * alignment. |
| */ |
| enum qca_wlan_vendor_peer_cfr_capture_attr { |
| QCA_WLAN_VENDOR_ATTR_PEER_CFR_CAPTURE_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_CFR_PEER_MAC_ADDR = 1, |
| QCA_WLAN_VENDOR_ATTR_PEER_CFR_ENABLE = 2, |
| QCA_WLAN_VENDOR_ATTR_PEER_CFR_BANDWIDTH = 3, |
| QCA_WLAN_VENDOR_ATTR_PEER_CFR_PERIODICITY = 4, |
| QCA_WLAN_VENDOR_ATTR_PEER_CFR_METHOD = 5, |
| QCA_WLAN_VENDOR_ATTR_PERIODIC_CFR_CAPTURE_ENABLE = 6, |
| QCA_WLAN_VENDOR_ATTR_PEER_CFR_VERSION = 7, |
| QCA_WLAN_VENDOR_ATTR_PEER_CFR_ENABLE_GROUP_BITMAP = 8, |
| QCA_WLAN_VENDOR_ATTR_PEER_CFR_DURATION = 9, |
| QCA_WLAN_VENDOR_ATTR_PEER_CFR_INTERVAL = 10, |
| QCA_WLAN_VENDOR_ATTR_PEER_CFR_CAPTURE_TYPE = 11, |
| QCA_WLAN_VENDOR_ATTR_PEER_CFR_UL_MU_MASK = 12, |
| QCA_WLAN_VENDOR_ATTR_PEER_CFR_FREEZE_TLV_DELAY_COUNT = 13, |
| QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_TABLE = 14, |
| QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_ENTRY = 15, |
| QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_NUMBER = 16, |
| QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_TA = 17, |
| QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_RA = 18, |
| QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_TA_MASK = 19, |
| QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_RA_MASK = 20, |
| QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_NSS = 21, |
| QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_BW = 22, |
| QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_MGMT_FILTER = 23, |
| QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_CTRL_FILTER = 24, |
| QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_DATA_FILTER = 25, |
| QCA_WLAN_VENDOR_ATTR_PEER_CFR_DATA_TRANSPORT_MODE = 26, |
| QCA_WLAN_VENDOR_ATTR_PEER_CFR_DATA_RECEIVER_PID = 27, |
| QCA_WLAN_VENDOR_ATTR_PEER_CFR_RESP_DATA = 28, |
| QCA_WLAN_VENDOR_ATTR_PEER_CFR_PAD = 29, |
| |
| /* Keep last */ |
| QCA_WLAN_VENDOR_ATTR_PEER_CFR_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_PEER_CFR_MAX = |
| QCA_WLAN_VENDOR_ATTR_PEER_CFR_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_throughput_level - Current throughput level |
| * |
| * Indicates the current level of throughput calculated by the driver. The |
| * driver may choose different thresholds to decide whether the throughput level |
| * is low or medium or high based on variety of parameters like physical link |
| * capacity of the current connection, the number of packets being dispatched |
| * per second, etc. The throughput level events might not be consistent with the |
| * actual current throughput value being observed. |
| * |
| * @QCA_WLAN_THROUGHPUT_LEVEL_LOW: Low level of throughput |
| * @QCA_WLAN_THROUGHPUT_LEVEL_MEDIUM: Medium level of throughput |
| * @QCA_WLAN_THROUGHPUT_LEVEL_HIGH: High level of throughput |
| */ |
| enum qca_wlan_throughput_level { |
| QCA_WLAN_THROUGHPUT_LEVEL_LOW = 0, |
| QCA_WLAN_THROUGHPUT_LEVEL_MEDIUM = 1, |
| QCA_WLAN_THROUGHPUT_LEVEL_HIGH = 2, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_throughput_change - Vendor subcmd attributes to |
| * report throughput changes from the driver to user space. enum values are used |
| * for netlink attributes sent with |
| * %QCA_NL80211_VENDOR_SUBCMD_THROUGHPUT_CHANGE_EVENT sub command. |
| */ |
| enum qca_wlan_vendor_attr_throughput_change { |
| QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_INVALID = 0, |
| /* Indicates the direction of throughput in which the change is being |
| * reported. u8 attribute. Value is 0 for TX and 1 for RX. |
| */ |
| QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_DIRECTION = 1, |
| /* Indicates the newly observed throughput level. enum |
| * qca_wlan_throughput_level describes the possible range of values. |
| * u8 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_THROUGHPUT_LEVEL = 2, |
| /* Indicates the driver's guidance on the new value to be set to |
| * kernel's TCP parameter tcp_limit_output_bytes. u32 attribute. The |
| * driver may optionally include this attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_TCP_LIMIT_OUTPUT_BYTES = 3, |
| /* Indicates the driver's guidance on the new value to be set to |
| * kernel's TCP parameter tcp_adv_win_scale. s8 attribute. Possible |
| * values are from -31 to 31. The driver may optionally include this |
| * attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_TCP_ADV_WIN_SCALE = 4, |
| /* Indicates the driver's guidance on the new value to be set to |
| * kernel's TCP parameter tcp_delack_seg. u32 attribute. The driver may |
| * optionally include this attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_TCP_DELACK_SEG = 5, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_MAX = |
| QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_coex_config_profiles - This enum defines different types of |
| * traffic streams that can be prioritized one over the other during coex |
| * scenarios. |
| * The types defined in this enum are categorized in the below manner. |
| * 0 - 31 values corresponds to WLAN |
| * 32 - 63 values corresponds to BT |
| * 64 - 95 values corresponds to Zigbee |
| * @QCA_WIFI_STA_DISCOVERY: Prioritize discovery frames for WLAN STA |
| * @QCA_WIFI_STA_CONNECTION: Prioritize connection frames for WLAN STA |
| * @QCA_WIFI_STA_CLASS_3_MGMT: Prioritize class 3 mgmt frames for WLAN STA |
| * @QCA_WIFI_STA_DATA : Prioritize data frames for WLAN STA |
| * @QCA_WIFI_STA_ALL: Priritize all frames for WLAN STA |
| * @QCA_WIFI_SAP_DISCOVERY: Prioritize discovery frames for WLAN SAP |
| * @QCA_WIFI_SAP_CONNECTION: Prioritize connection frames for WLAN SAP |
| * @QCA_WIFI_SAP_CLASS_3_MGMT: Prioritize class 3 mgmt frames for WLAN SAP |
| * @QCA_WIFI_SAP_DATA: Prioritize data frames for WLAN SAP |
| * @QCA_WIFI_SAP_ALL: Prioritize all frames for WLAN SAP |
| * @QCA_BT_A2DP: Prioritize BT A2DP |
| * @QCA_BT_BLE: Prioritize BT BLE |
| * @QCA_BT_SCO: Prioritize BT SCO |
| * @QCA_ZB_LOW: Prioritize Zigbee Low |
| * @QCA_ZB_HIGH: Prioritize Zigbee High |
| */ |
| enum qca_coex_config_profiles { |
| /* 0 - 31 corresponds to WLAN */ |
| QCA_WIFI_STA_DISCOVERY = 0, |
| QCA_WIFI_STA_CONNECTION = 1, |
| QCA_WIFI_STA_CLASS_3_MGMT = 2, |
| QCA_WIFI_STA_DATA = 3, |
| QCA_WIFI_STA_ALL = 4, |
| QCA_WIFI_SAP_DISCOVERY = 5, |
| QCA_WIFI_SAP_CONNECTION = 6, |
| QCA_WIFI_SAP_CLASS_3_MGMT = 7, |
| QCA_WIFI_SAP_DATA = 8, |
| QCA_WIFI_SAP_ALL = 9, |
| QCA_WIFI_CASE_MAX = 31, |
| /* 32 - 63 corresponds to BT */ |
| QCA_BT_A2DP = 32, |
| QCA_BT_BLE = 33, |
| QCA_BT_SCO = 34, |
| QCA_BT_CASE_MAX = 63, |
| /* 64 - 95 corresponds to Zigbee */ |
| QCA_ZB_LOW = 64, |
| QCA_ZB_HIGH = 65, |
| QCA_ZB_CASE_MAX = 95, |
| /* 0xff is default value if the u8 profile value is not set. */ |
| QCA_COEX_CONFIG_PROFILE_DEFAULT_VALUE = 255 |
| }; |
| |
| /** |
| * enum qca_vendor_attr_coex_config_types - Coex configurations types. |
| * This enum defines the valid set of values of coex configuration types. These |
| * values may used by attribute |
| * %QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_CONFIG_TYPE. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_COEX_RESET: Reset all the |
| * weights to default values. |
| * @QCA_WLAN_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_COEX_START: Start to config |
| * weights with configurability value. |
| */ |
| enum qca_vendor_attr_coex_config_types { |
| QCA_WLAN_VENDOR_ATTR_COEX_CONFIG_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_COEX_RESET = 1, |
| QCA_WLAN_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_COEX_START = 2, |
| }; |
| |
| /** |
| * enum qca_vendor_attr_coex_config - Specifies vendor coex config attributes |
| * |
| * @QCA_VENDOR_ATTR_COEX_CONFIG_PROFILES: This attribute contains variable |
| * length array of 8-bit values from enum qca_coex_config_profiles. |
| * FW will prioritize the profiles in the order given in the array encapsulated |
| * in this attribute. |
| * For example: |
| * ----------------------------------------------------------------------- |
| * | 1 | 34 | 32 | 65 | |
| * ----------------------------------------------------------------------- |
| * If the attribute contains the values defined in above array then it means |
| * 1) Wifi STA connection has priority over BT_SCO, BT_A2DP and ZIGBEE HIGH. |
| * 2) BT_SCO has priority over BT_A2DP. |
| * 3) BT_A2DP has priority over ZIGBEE HIGH. |
| * Profiles which are not listed in this array shall not be preferred over the |
| * profiles which are listed in the array as a part of this attribute. |
| */ |
| enum qca_vendor_attr_coex_config { |
| QCA_VENDOR_ATTR_COEX_CONFIG_INVALID = 0, |
| QCA_VENDOR_ATTR_COEX_CONFIG_PROFILES = 1, |
| |
| /* Keep last */ |
| QCA_VENDOR_ATTR_COEX_CONFIG_AFTER_LAST, |
| QCA_VENDOR_ATTR_COEX_CONFIG_MAX = |
| QCA_VENDOR_ATTR_COEX_CONFIG_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_vendor_attr_coex_config_three_way - Specifies vendor coex config |
| * attributes |
| * Attributes for data used by QCA_NL80211_VENDOR_SUBCMD_COEX_CONFIG |
| * |
| * QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_CONFIG_TYPE: u32 attribute. |
| * Indicate config type. |
| * The config types are 32-bit values from qca_vendor_attr_coex_config_types |
| * |
| * @QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_1: u32 attribute. |
| * Indicate the Priority 1 profiles. |
| * The profiles are 8-bit values from enum qca_coex_config_profiles. |
| * In same priority level, maximum to 4 profiles can be set here. |
| * @QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_2: u32 attribute. |
| * Indicate the Priority 2 profiles. |
| * The profiles are 8-bit values from enum qca_coex_config_profiles. |
| * In same priority level, maximum to 4 profiles can be set here. |
| * @QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_3: u32 attribute. |
| * Indicate the Priority 3 profiles. |
| * The profiles are 8-bit values from enum qca_coex_config_profiles. |
| * In same priority level, maximum to 4 profiles can be set here. |
| * @QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_4: u32 attribute. |
| * Indicate the Priority 4 profiles. |
| * The profiles are 8-bit values from enum qca_coex_config_profiles. |
| * In same priority level, maximum to 4 profiles can be set here. |
| * NOTE: |
| * Limitations for QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_x priority |
| * arrangement: |
| * 1: In the same u32 attribute (priority x), the profiles enum values own |
| * same priority level. |
| * 2: 0xff is default value if the u8 profile value is not set. |
| * 3: max to 4 rules/profiles in same priority level. |
| * 4: max to 4 priority level (priority 1 - priority 4) |
| * 5: one priority level only supports one scenario from WLAN/BT/ZB, |
| * hybrid rules not support. |
| * 6: if WMI_COEX_CONFIG_THREE_WAY_COEX_RESET called, priority x will |
| * remain blank to reset all parameters. |
| * For example: |
| * |
| * If the attributes as follow: |
| * priority 1: |
| * ------------------------------------ |
| * | 0xff | 0 | 1 | 2 | |
| * ------------------------------------ |
| * priority 2: |
| * ------------------------------------- |
| * | 0xff | 0xff | 0xff | 32 | |
| * ------------------------------------- |
| * priority 3: |
| * ------------------------------------- |
| * | 0xff | 0xff | 0xff | 65 | |
| * ------------------------------------- |
| * then it means: |
| * 1: WIFI_STA_DISCOVERY, WIFI_STA_CLASS_3_MGMT and WIFI_STA_CONNECTION |
| * owns same priority level. |
| * 2: WIFI_STA_DISCOVERY, WIFI_STA_CLASS_3_MGMT and WIFI_STA_CONNECTION |
| * has priority over BT_A2DP and ZB_HIGH. |
| * 3: BT_A2DP has priority over ZB_HIGH. |
| */ |
| enum qca_vendor_attr_coex_config_three_way { |
| QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_INVALID = 0, |
| QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_CONFIG_TYPE = 1, |
| QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_1 = 2, |
| QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_2 = 3, |
| QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_3 = 4, |
| QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_4 = 5, |
| |
| /* Keep last */ |
| QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_AFTER_LAST, |
| QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_MAX = |
| QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_link_properties - Represent the link properties. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_MAC_ADDR: MAC address of the peer |
| * (STA/AP) for the connected link. |
| * @QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_STA_FLAGS: Attribute containing a |
| * &struct nl80211_sta_flag_update for the respective connected link. MAC |
| * address of the peer represented by |
| * QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_MAC_ADDR. |
| */ |
| enum qca_wlan_vendor_attr_link_properties { |
| QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_INVALID = 0, |
| /* 1 - 3 are reserved */ |
| QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_MAC_ADDR = 4, |
| QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_STA_FLAGS = 5, |
| |
| /* Keep last */ |
| QCA_VENDOR_ATTR_LINK_PROPERTIES_AFTER_LAST, |
| QCA_VENDOR_ATTR_LINK_PROPERTIES_MAX = |
| QCA_VENDOR_ATTR_LINK_PROPERTIES_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_vendor_attr_peer_stats_cache_type - Represents peer stats cache type |
| * This enum defines the valid set of values of peer stats cache types. These |
| * values are used by attribute |
| * %QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_TYPE. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_PEER_TX_RATE_STATS: Represents peer TX rate statistics |
| * @QCA_WLAN_VENDOR_ATTR_PEER_RX_RATE_STATS: Represents peer RX rate statistics |
| * @QCA_WLAN_VENDOR_ATTR_PEER_TX_SOJOURN_STATS: Represents peer TX sojourn |
| * statistics |
| */ |
| enum qca_vendor_attr_peer_stats_cache_type { |
| QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_TYPE_INVALID = 0, |
| |
| QCA_WLAN_VENDOR_ATTR_PEER_TX_RATE_STATS, |
| QCA_WLAN_VENDOR_ATTR_PEER_RX_RATE_STATS, |
| QCA_WLAN_VENDOR_ATTR_PEER_TX_SOJOURN_STATS, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_peer_stats_cache_params - This enum defines |
| * attributes required for QCA_NL80211_VENDOR_SUBCMD_PEER_STATS_CACHE_FLUSH |
| * Information in these attributes is used to flush peer rate statistics from |
| * the driver to user application. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_TYPE: Unsigned 32-bit attribute |
| * Indicate peer statistics cache type. |
| * The statistics types are 32-bit values from |
| * enum qca_vendor_attr_peer_stats_cache_type. |
| * @QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_PEER_MAC: Unsigned 8-bit array |
| * of size 6 octets, representing the peer MAC address. |
| * @QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_DATA: Opaque data attribute |
| * containing buffer of statistics to send to application layer entity. |
| * @QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_PEER_COOKIE: Unsigned 64-bit attribute |
| * representing a cookie for peer unique session. |
| * @QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_PAD: Attribute used for padding for |
| * 64-bit alignment. |
| */ |
| enum qca_wlan_vendor_attr_peer_stats_cache_params { |
| QCA_WLAN_VENDOR_ATTR_PEER_STATS_INVALID = 0, |
| |
| QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_TYPE = 1, |
| QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_PEER_MAC = 2, |
| QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_DATA = 3, |
| QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_PEER_COOKIE = 4, |
| QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_PAD = 5, |
| |
| /* Keep last */ |
| QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_LAST, |
| QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_MAX = |
| QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_LAST - 1 |
| }; |
| |
| /** |
| * enum qca_mpta_helper_attr_zigbee_state - Current Zigbee state |
| * This enum defines all the possible states of Zigbee, which can be |
| * delivered in the QCA_MPTA_HELPER_VENDOR_ATTR_ZIGBEE_STATE attribute. |
| * |
| * @ZIGBEE_IDLE: Zigbee in idle state |
| * @ZIGBEE_FORM_NETWORK: Zigbee forming network |
| * @ZIGBEE_WAIT_JOIN: Zigbee waiting for joining network |
| * @ZIGBEE_JOIN: Zigbee joining network |
| * @ZIGBEE_NETWORK_UP: Zigbee network is up |
| * @ZIGBEE_HMI: Zigbee in HMI mode |
| */ |
| enum qca_mpta_helper_attr_zigbee_state { |
| ZIGBEE_IDLE = 0, |
| ZIGBEE_FORM_NETWORK = 1, |
| ZIGBEE_WAIT_JOIN = 2, |
| ZIGBEE_JOIN = 3, |
| ZIGBEE_NETWORK_UP = 4, |
| ZIGBEE_HMI = 5, |
| }; |
| |
| /* |
| * enum qca_mpta_helper_vendor_attr - Attributes used in vendor sub-command |
| * QCA_NL80211_VENDOR_SUBCMD_MPTA_HELPER_CONFIG. |
| */ |
| enum qca_mpta_helper_vendor_attr { |
| QCA_MPTA_HELPER_VENDOR_ATTR_INVALID = 0, |
| /* Optional attribute used to update Zigbee state. |
| * enum qca_mpta_helper_attr_zigbee_state. |
| * NLA_U32 attribute. |
| */ |
| QCA_MPTA_HELPER_VENDOR_ATTR_ZIGBEE_STATE = 1, |
| /* Optional attribute used to configure WLAN duration for Shape-OCS |
| * during interrupt. |
| * Set in pair with QCA_MPTA_HELPER_VENDOR_ATTR_INT_NON_WLAN_DURATION. |
| * Value range 0 ~ 300 (ms). |
| * NLA_U32 attribute. |
| */ |
| QCA_MPTA_HELPER_VENDOR_ATTR_INT_WLAN_DURATION = 2, |
| /* Optional attribute used to configure non-WLAN duration for Shape-OCS |
| * during interrupt. |
| * Set in pair with QCA_MPTA_HELPER_VENDOR_ATTR_INT_WLAN_DURATION. |
| * Value range 0 ~ 300 (ms). |
| * NLA_U32 attribute. |
| */ |
| QCA_MPTA_HELPER_VENDOR_ATTR_INT_NON_WLAN_DURATION = 3, |
| /* Optional attribute used to configure WLAN duration for Shape-OCS |
| * monitor period. |
| * Set in pair with QCA_MPTA_HELPER_VENDOR_ATTR_MON_NON_WLAN_DURATION. |
| * Value range 0 ~ 300 (ms) |
| * NLA_U32 attribute |
| */ |
| QCA_MPTA_HELPER_VENDOR_ATTR_MON_WLAN_DURATION = 4, |
| /* Optional attribute used to configure non-WLAN duration for Shape-OCS |
| * monitor period. |
| * Set in pair with QCA_MPTA_HELPER_VENDOR_ATTR_MON_WLAN_DURATION. |
| * Value range 0 ~ 300 (ms) |
| * NLA_U32 attribute |
| */ |
| QCA_MPTA_HELPER_VENDOR_ATTR_MON_NON_WLAN_DURATION = 5, |
| /* Optional attribute used to configure OCS interrupt duration. |
| * Set in pair with QCA_MPTA_HELPER_VENDOR_ATTR_MON_OCS_DURATION. |
| * Value range 1000 ~ 20000 (ms) |
| * NLA_U32 attribute |
| */ |
| QCA_MPTA_HELPER_VENDOR_ATTR_INT_OCS_DURATION = 6, |
| /* Optional attribute used to configure OCS monitor duration. |
| * Set in pair with QCA_MPTA_HELPER_VENDOR_ATTR_INT_OCS_DURATION. |
| * Value range 1000 ~ 20000 (ms) |
| * NLA_U32 attribute |
| */ |
| QCA_MPTA_HELPER_VENDOR_ATTR_MON_OCS_DURATION = 7, |
| /* Optional attribute used to notify WLAN firmware the current Zigbee |
| * channel. |
| * Value range 11 ~ 26 |
| * NLA_U32 attribute |
| */ |
| QCA_MPTA_HELPER_VENDOR_ATTR_ZIGBEE_CHAN = 8, |
| /* Optional attribute used to configure WLAN mute duration. |
| * Value range 0 ~ 400 (ms) |
| * NLA_U32 attribute |
| */ |
| QCA_MPTA_HELPER_VENDOR_ATTR_WLAN_MUTE_DURATION = 9, |
| |
| /* keep last */ |
| QCA_MPTA_HELPER_VENDOR_ATTR_AFTER_LAST, |
| QCA_MPTA_HELPER_VENDOR_ATTR_MAX = |
| QCA_MPTA_HELPER_VENDOR_ATTR_AFTER_LAST - 1 |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_beacon_reporting_op_types - Defines different types of |
| * operations for which %QCA_NL80211_VENDOR_SUBCMD_BEACON_REPORTING can be used. |
| * Will be used by %QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE. |
| * |
| * @QCA_WLAN_VENDOR_BEACON_REPORTING_OP_START: Sent by userspace to the driver |
| * to request the driver to start reporting Beacon frames. |
| * @QCA_WLAN_VENDOR_BEACON_REPORTING_OP_STOP: Sent by userspace to the driver to |
| * request the driver to stop reporting Beacon frames. |
| * @QCA_WLAN_VENDOR_BEACON_REPORTING_OP_BEACON_INFO: Sent by the driver to |
| * userspace to report received Beacon frames. |
| * @QCA_WLAN_VENDOR_BEACON_REPORTING_OP_PAUSE: Sent by the driver to userspace |
| * to indicate that the driver is going to pause reporting Beacon frames. |
| */ |
| enum qca_wlan_vendor_beacon_reporting_op_types { |
| QCA_WLAN_VENDOR_BEACON_REPORTING_OP_START = 0, |
| QCA_WLAN_VENDOR_BEACON_REPORTING_OP_STOP = 1, |
| QCA_WLAN_VENDOR_BEACON_REPORTING_OP_BEACON_INFO = 2, |
| QCA_WLAN_VENDOR_BEACON_REPORTING_OP_PAUSE = 3, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_beacon_reporting_pause_reasons - Defines different types |
| * of reasons for which the driver is pausing reporting Beacon frames. Will be |
| * used by %QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_PAUSE_REASON. |
| * |
| * @QCA_WLAN_VENDOR_BEACON_REPORTING_PAUSE_REASON_UNSPECIFIED: For unspecified |
| * reasons. |
| * @QCA_WLAN_VENDOR_BEACON_REPORTING_PAUSE_REASON_SCAN_STARTED: When the |
| * driver/firmware is starting a scan. |
| * @QCA_WLAN_VENDOR_BEACON_REPORTING_PAUSE_REASON_DISCONNECTED: When the |
| * driver/firmware disconnects from the ESS and indicates the disconnection to |
| * userspace (non-seamless roaming case). This reason code will be used by the |
| * driver/firmware to indicate stopping of beacon report events. Userspace will |
| * need to start beacon reporting again (if desired) by sending vendor command |
| * QCA_NL80211_VENDOR_SUBCMD_BEACON_REPORTING with |
| * QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE set to |
| * QCA_WLAN_VENDOR_BEACON_REPORTING_OP_START after the next connection is |
| * completed. |
| */ |
| enum qca_wlan_vendor_beacon_reporting_pause_reasons { |
| QCA_WLAN_VENDOR_BEACON_REPORTING_PAUSE_REASON_UNSPECIFIED = 0, |
| QCA_WLAN_VENDOR_BEACON_REPORTING_PAUSE_REASON_SCAN_STARTED = 1, |
| QCA_WLAN_VENDOR_BEACON_REPORTING_PAUSE_REASON_DISCONNECTED = 2, |
| }; |
| |
| /* |
| * enum qca_wlan_vendor_attr_beacon_reporting_params - List of attributes used |
| * in vendor sub-command QCA_NL80211_VENDOR_SUBCMD_BEACON_REPORTING. |
| */ |
| enum qca_wlan_vendor_attr_beacon_reporting_params { |
| QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_INVALID = 0, |
| /* Specifies the type of operation that the vendor command/event is |
| * intended for. Possible values for this attribute are defined in |
| * enum qca_wlan_vendor_beacon_reporting_op_types. u32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE = 1, |
| /* Optionally set by userspace to request the driver to report Beacon |
| * frames using asynchronous vendor events when the |
| * QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE is set to |
| * QCA_WLAN_VENDOR_BEACON_REPORTING_OP_START. NLA_FLAG attribute. |
| * If this flag is not set, the driver will only update Beacon frames in |
| * cfg80211 scan cache but not send any vendor events. |
| */ |
| QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_ACTIVE_REPORTING = 2, |
| /* Optionally used by userspace to request the driver/firmware to report |
| * Beacon frames periodically when the |
| * QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE is set to |
| * QCA_WLAN_VENDOR_BEACON_REPORTING_OP_START. |
| * u32 attribute, indicates the period of Beacon frames to be reported |
| * and in the units of beacon interval. |
| * If this attribute is missing in the command, then the default value |
| * of 1 will be assumed by driver, i.e., to report every Beacon frame. |
| * Zero is an invalid value. |
| * If a valid value is received for this attribute, the driver will |
| * update the cfg80211 scan cache periodically as per the value received |
| * in this attribute in addition to updating the cfg80211 scan cache |
| * when there is significant change in Beacon frame IEs. |
| */ |
| QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_PERIOD = 3, |
| /* Used by the driver to encapsulate the SSID when the |
| * QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE is set to |
| * QCA_WLAN_VENDOR_BEACON_REPORTING_OP_BEACON_INFO. |
| * u8 array with a maximum size of 32. |
| * |
| * When generating beacon report from non-MBSSID Beacon frame, the SSID |
| * will be taken from the SSID element of the received Beacon frame. |
| * |
| * When generating beacon report from Multiple BSSID Beacon frame and if |
| * the BSSID of the current connected BSS matches the BSSID of the |
| * transmitting BSS, the SSID will be taken from the SSID element of the |
| * received Beacon frame. |
| * |
| * When generating beacon report from Multiple BSSID Beacon frame and if |
| * the BSSID of the current connected BSS matches the BSSID of one of |
| * the* nontransmitting BSSs, the SSID will be taken from the SSID field |
| * included in the nontransmitted BSS profile whose derived BSSID is |
| * same as the BSSID of the current connected BSS. When there is no |
| * nontransmitted BSS profile whose derived BSSID is same as the BSSID |
| * of current connected* BSS, this attribute will not be present. |
| */ |
| QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_SSID = 4, |
| /* Used by the driver to encapsulate the BSSID of the AP to which STA is |
| * currently connected to when the |
| * QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE is set to |
| * QCA_WLAN_VENDOR_BEACON_REPORTING_OP_BEACON_INFO. u8 array with a |
| * fixed size of 6 bytes. |
| * |
| * When generating beacon report from a Multiple BSSID beacon and the |
| * current connected BSSID matches one of the nontransmitted BSSIDs in a |
| * Multiple BSSID set, this BSSID will be that particular nontransmitted |
| * BSSID and not the transmitted BSSID (i.e., the transmitting address |
| * of the Beacon frame). |
| */ |
| QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_BSSID = 5, |
| /* Used by the driver to encapsulate the frequency in MHz on which |
| * the Beacon frame was received when the |
| * QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE is |
| * set to QCA_WLAN_VENDOR_BEACON_REPORTING_OP_BEACON_INFO. |
| * u32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_FREQ = 6, |
| /* Used by the driver to encapsulate the Beacon interval |
| * when the QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE is set to |
| * QCA_WLAN_VENDOR_BEACON_REPORTING_OP_BEACON_INFO. |
| * u16 attribute. The value will be copied from the Beacon frame and the |
| * units are TUs. |
| */ |
| QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_BI = 7, |
| /* Used by the driver to encapsulate the Timestamp field from the Beacon |
| * frame when the QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE is set |
| * to QCA_WLAN_VENDOR_BEACON_REPORTING_OP_BEACON_INFO. |
| * u64 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_TSF = 8, |
| /* Used by the driver to encapsulate the CLOCK_BOOTTIME when this |
| * Beacon frame is received in the driver when the |
| * QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE is set to |
| * QCA_WLAN_VENDOR_BEACON_REPORTING_OP_BEACON_INFO. u64 attribute, in |
| * the units of nanoseconds. This value is expected to have accuracy of |
| * about 10 ms. |
| */ |
| QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_BOOTTIME_WHEN_RECEIVED = 9, |
| /* Used by the driver to encapsulate the IEs of the Beacon frame from |
| * which this event is generated when the |
| * QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE is set to |
| * QCA_WLAN_VENDOR_BEACON_REPORTING_OP_BEACON_INFO. u8 array. |
| */ |
| QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_IES = 10, |
| /* Used by the driver to specify the reason for the driver/firmware to |
| * pause sending beacons to userspace when the |
| * QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE is set to |
| * QCA_WLAN_VENDOR_BEACON_REPORTING_OP_PAUSE. Possible values are |
| * defined in enum qca_wlan_vendor_beacon_reporting_pause_reasons, u32 |
| * attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_PAUSE_REASON = 11, |
| /* Used by the driver to specify whether the driver will automatically |
| * resume reporting beacon events to userspace later (for example after |
| * the ongoing off-channel activity is completed etc.) when the |
| * QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE is set to |
| * QCA_WLAN_VENDOR_BEACON_REPORTING_OP_PAUSE. NLA_FLAG attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_AUTO_RESUMES = 12, |
| /* Optionally set by userspace to request the driver not to resume |
| * beacon reporting after a pause is completed, when the |
| * QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE is set to |
| * QCA_WLAN_VENDOR_BEACON_REPORTING_OP_START. NLA_FLAG attribute. |
| * If this flag is set, the driver will not resume beacon reporting |
| * after any pause in beacon reporting is completed. Userspace has to |
| * send QCA_WLAN_VENDOR_BEACON_REPORTING_OP_START command again in order |
| * to initiate beacon reporting again. If this flag is set in the recent |
| * QCA_WLAN_VENDOR_BEACON_REPORTING_OP_START command, then in the |
| * subsequent QCA_WLAN_VENDOR_BEACON_REPORTING_OP_PAUSE event (if any) |
| * the QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_AUTO_RESUMES shall not be |
| * set by the driver. Setting this flag until and unless there is a |
| * specific need is not recommended as there is a chance of some beacons |
| * received after pause command and next start command being not |
| * reported. |
| */ |
| QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_DO_NOT_RESUME = 13, |
| /* Attribute used for padding for 64-bit alignment */ |
| QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_PAD = 14, |
| |
| /* Keep last */ |
| QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_LAST, |
| QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_MAX = |
| QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_LAST - 1 |
| }; |
| |
| /** |
| * enum qca_vendor_interop_issues_ap_type - Interop issue types |
| * This enum defines the valid set of values of interop issue types. These |
| * values are used by attribute %QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_TYPE. |
| * |
| * @QCA_VENDOR_INTEROP_ISSUES_AP_ON_STA_PS: The AP has power save interop issue |
| * when the STA's Qpower feature is enabled. |
| */ |
| enum qca_vendor_interop_issues_ap_type { |
| QCA_VENDOR_INTEROP_ISSUES_AP_INVALID = 0, |
| QCA_VENDOR_INTEROP_ISSUES_AP_ON_STA_PS = 1, |
| }; |
| |
| /** |
| * enum qca_vendor_attr_interop_issues_ap - attribute for AP with interop issues |
| * Values are used by %QCA_NL80211_VENDOR_SUBCMD_INTEROP_ISSUES_AP. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_INVALID: Invalid value |
| * @QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_TYPE: Interop issue type |
| * 32-bit unsigned value. The values defined in enum |
| * qca_vendor_interop_issues_ap_type are used. |
| * @QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_LIST: APs' BSSID container |
| * array of nested QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_BSSID attributes. |
| * It is present and mandatory for the command but is not used for the event |
| * since only a single BSSID is reported in an event. |
| * @QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_BSSID: AP's BSSID 6-byte MAC address. |
| * It is used within the nested QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_LIST |
| * attribute in command case and without such encapsulation in the event case. |
| * @QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_AFTER_LAST: last value |
| * @QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_MAX: max value |
| */ |
| enum qca_vendor_attr_interop_issues_ap { |
| QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_INVALID, |
| QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_TYPE, |
| QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_LIST, |
| QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_BSSID, |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_MAX = |
| QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_AFTER_LAST - 1 |
| }; |
| |
| /** |
| * enum qca_vendor_oem_device_type - Represents the target device in firmware. |
| * It is used by QCA_WLAN_VENDOR_ATTR_OEM_DEVICE_INFO. |
| * |
| * @QCA_VENDOR_OEM_DEVICE_VIRTUAL: The command is intended for |
| * a virtual device. |
| * |
| * @QCA_VENDOR_OEM_DEVICE_PHYSICAL: The command is intended for |
| * a physical device. |
| */ |
| enum qca_vendor_oem_device_type { |
| QCA_VENDOR_OEM_DEVICE_VIRTUAL = 0, |
| QCA_VENDOR_OEM_DEVICE_PHYSICAL = 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_oem_data_params - Used by the vendor command/event |
| * QCA_NL80211_VENDOR_SUBCMD_OEM_DATA. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_OEM_DATA_CMD_DATA: This NLA_BINARY attribute is |
| * used to set/query the data to/from the firmware. On query, the same |
| * attribute is used to carry the respective data in the reply sent by the |
| * driver to userspace. The request to set/query the data and the format of the |
| * respective data from the firmware are embedded in the attribute. The |
| * maximum size of the attribute payload is 1024 bytes. |
| * Userspace has to set the QCA_WLAN_VENDOR_ATTR_OEM_DATA_RESPONSE_EXPECTED |
| * attribute when the data is queried from the firmware. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_OEM_DEVICE_INFO: The binary blob will be routed |
| * based on this field. This optional attribute is included to specify whether |
| * the device type is a virtual device or a physical device for the |
| * command/event. This attribute can be omitted for a virtual device (default) |
| * command/event. |
| * This u8 attribute is used to carry information for the device type using |
| * values defined by enum qca_vendor_oem_device_type. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_OEM_DATA_RESPONSE_EXPECTED: This NLA_FLAG attribute |
| * is set when the userspace queries data from the firmware. This attribute |
| * should not be set when userspace sets the OEM data to the firmware. |
| */ |
| enum qca_wlan_vendor_attr_oem_data_params { |
| QCA_WLAN_VENDOR_ATTR_OEM_DATA_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_OEM_DATA_CMD_DATA = 1, |
| QCA_WLAN_VENDOR_ATTR_OEM_DEVICE_INFO = 2, |
| QCA_WLAN_VENDOR_ATTR_OEM_DATA_RESPONSE_EXPECTED = 3, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_OEM_DATA_PARAMS_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_OEM_DATA_PARAMS_MAX = |
| QCA_WLAN_VENDOR_ATTR_OEM_DATA_PARAMS_AFTER_LAST - 1 |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_avoid_frequency_ext - Defines attributes to be |
| * used with vendor command/event QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY_EXT. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_RANGE: Required |
| * Nested attribute containing multiple ranges with following attributes: |
| * QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_START, |
| * QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_END, and |
| * QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_POWER_CAP_DBM. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_START: Required (u32) |
| * Starting center frequency in MHz. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_END: Required (u32) |
| * Ending center frequency in MHz. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_POWER_CAP_DBM: |
| * s32 attribute, optional. It is a per frequency range attribute. |
| * The maximum TX power limit from user space is to be applied on an |
| * unrestricted interface for corresponding frequency range. It is also |
| * possible that the actual TX power may be even lower than this cap due to |
| * other considerations such as regulatory compliance, SAR, etc. In absence of |
| * this attribute the driver shall follow current behavior which means |
| * interface (SAP/P2P) function can keep operating on an unsafe channel with TX |
| * power derived by the driver based on regulatory/SAR during interface up. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_IFACES_BITMASK: |
| * u32 attribute, optional. Indicates all the interface types which are |
| * restricted for all frequency ranges provided in |
| * %QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_START and |
| * %QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_END. |
| * This attribute encapsulates bitmasks of interface types defined in |
| * enum nl80211_iftype. If an interface is marked as restricted the driver must |
| * move to a safe channel and if no safe channel is available the driver shall |
| * terminate that interface functionality. In absence of this attribute, |
| * interface (SAP/P2P) can still continue operating on an unsafe channel with |
| * TX power limit derived from either |
| * %QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_POWER_CAP_DBM or based on |
| * regulatory/SAE limits if %QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_POWER_CAP_DBM |
| * is not provided. |
| */ |
| enum qca_wlan_vendor_attr_avoid_frequency_ext { |
| QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_RANGE = 1, |
| QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_START = 2, |
| QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_END = 3, |
| QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_POWER_CAP_DBM = 4, |
| QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_IFACES_BITMASK = 5, |
| |
| QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_MAX = |
| QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_AFTER_LAST - 1 |
| }; |
| |
| /* |
| * enum qca_wlan_vendor_attr_add_sta_node_params - Used by the vendor command |
| * QCA_NL80211_VENDOR_SUBCMD_ADD_STA_NODE. |
| */ |
| enum qca_wlan_vendor_attr_add_sta_node_params { |
| QCA_WLAN_VENDOR_ATTR_ADD_STA_NODE_INVALID = 0, |
| /* 6 byte MAC address of STA */ |
| QCA_WLAN_VENDOR_ATTR_ADD_STA_NODE_MAC_ADDR = 1, |
| /* Authentication algorithm used by the station of size u16; |
| * defined in enum nl80211_auth_type. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ADD_STA_NODE_AUTH_ALGO = 2, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_ADD_STA_NODE_PARAM_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_ADD_STA_NODE_PARAM_MAX = |
| QCA_WLAN_VENDOR_ATTR_ADD_STA_NODE_PARAM_AFTER_LAST - 1 |
| }; |
| |
| /** |
| * enum qca_btc_chain_mode - Specifies BT coex chain mode. |
| * This enum defines the valid set of values of BT coex chain mode. |
| * These values are used by attribute %QCA_VENDOR_ATTR_BTC_CHAIN_MODE of |
| * %QCA_NL80211_VENDOR_SUBCMD_BTC_CHAIN_MODE. |
| * |
| * @QCA_BTC_CHAIN_SHARED: chains of BT and WLAN 2.4 GHz are shared. |
| * @QCA_BTC_CHAIN_SEPARATED_HYBRID: chains of BT and WLAN 2.4 GHz are |
| * separated, hybrid mode. |
| * @QCA_BTC_CHAIN_SEPARATED_FDD: chains of BT and WLAN 2.4 GHz are |
| * separated, fixed FDD mode. |
| */ |
| enum qca_btc_chain_mode { |
| QCA_BTC_CHAIN_SHARED = 0, |
| QCA_BTC_CHAIN_SEPARATED_HYBRID = 1, |
| QCA_BTC_CHAIN_SEPARATED_FDD = 2, |
| }; |
| |
| /* deprecated legacy name */ |
| #define QCA_BTC_CHAIN_SEPARATED QCA_BTC_CHAIN_SEPARATED_HYBRID |
| |
| /** |
| * enum qca_vendor_attr_btc_chain_mode - Specifies attributes for BT coex |
| * chain mode. |
| * Attributes for data used by QCA_NL80211_VENDOR_SUBCMD_BTC_CHAIN_MODE. |
| * |
| * @QCA_VENDOR_ATTR_COEX_BTC_CHAIN_MODE: u32 attribute. |
| * Indicates the BT coex chain mode, are 32-bit values from |
| * enum qca_btc_chain_mode. This attribute is mandatory. |
| * |
| * @QCA_VENDOR_ATTR_COEX_BTC_CHAIN_MODE_RESTART: flag attribute. |
| * If set, vdev should be restarted when BT coex chain mode is updated. |
| * This attribute is optional. |
| */ |
| enum qca_vendor_attr_btc_chain_mode { |
| QCA_VENDOR_ATTR_BTC_CHAIN_MODE_INVALID = 0, |
| QCA_VENDOR_ATTR_BTC_CHAIN_MODE = 1, |
| QCA_VENDOR_ATTR_BTC_CHAIN_MODE_RESTART = 2, |
| |
| /* Keep last */ |
| QCA_VENDOR_ATTR_BTC_CHAIN_MODE_LAST, |
| QCA_VENDOR_ATTR_BTC_CHAIN_MODE_MAX = |
| QCA_VENDOR_ATTR_BTC_CHAIN_MODE_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_vendor_wlan_sta_flags - Station feature flags |
| * Bits will be set to 1 if the corresponding features are enabled. |
| * @QCA_VENDOR_WLAN_STA_FLAG_AMPDU: AMPDU is enabled for the station |
| * @QCA_VENDOR_WLAN_STA_FLAG_TX_STBC: TX Space-time block coding is enabled |
| for the station |
| * @QCA_VENDOR_WLAN_STA_FLAG_RX_STBC: RX Space-time block coding is enabled |
| for the station |
| */ |
| enum qca_vendor_wlan_sta_flags { |
| QCA_VENDOR_WLAN_STA_FLAG_AMPDU = BIT(0), |
| QCA_VENDOR_WLAN_STA_FLAG_TX_STBC = BIT(1), |
| QCA_VENDOR_WLAN_STA_FLAG_RX_STBC = BIT(2), |
| }; |
| |
| /** |
| * enum qca_vendor_wlan_sta_guard_interval - Station guard interval |
| * @QCA_VENDOR_WLAN_STA_GI_800_NS: Legacy normal guard interval |
| * @QCA_VENDOR_WLAN_STA_GI_400_NS: Legacy short guard interval |
| * @QCA_VENDOR_WLAN_STA_GI_1600_NS: Guard interval used by HE |
| * @QCA_VENDOR_WLAN_STA_GI_3200_NS: Guard interval used by HE |
| */ |
| enum qca_vendor_wlan_sta_guard_interval { |
| QCA_VENDOR_WLAN_STA_GI_800_NS = 0, |
| QCA_VENDOR_WLAN_STA_GI_400_NS = 1, |
| QCA_VENDOR_WLAN_STA_GI_1600_NS = 2, |
| QCA_VENDOR_WLAN_STA_GI_3200_NS = 3, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_get_sta_info - Defines attributes |
| * used by QCA_NL80211_VENDOR_SUBCMD_GET_STA_INFO vendor command. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_MAC: |
| * Required attribute in request for AP mode only, 6-byte MAC address, |
| * corresponding to the station's MAC address for which information is |
| * requested. For STA mode this is not required as the info always correspond |
| * to the self STA and the current/last association. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_FLAGS: |
| * Optionally used in response, u32 attribute, contains a bitmap of different |
| * fields defined in enum qca_vendor_wlan_sta_flags, used in AP mode only. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_GUARD_INTERVAL: |
| * Optionally used in response, u32 attribute, possible values are defined in |
| * enum qca_vendor_wlan_sta_guard_interval, used in AP mode only. |
| * Guard interval used by the station. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_RETRY_COUNT: |
| * Optionally used in response, u32 attribute, used in AP mode only. |
| * Value indicates the number of data frames received from station with retry |
| * bit set to 1 in FC. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_BC_MC_COUNT: |
| * Optionally used in response, u32 attribute, used in AP mode only. |
| * Counter for number of data frames with broadcast or multicast address in |
| * the destination address received from the station. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_RETRY_SUCCEED: |
| * Optionally used in response, u32 attribute, used in both STA and AP modes. |
| * Value indicates the number of data frames successfully transmitted only |
| * after retrying the packets and for which the TX status has been updated |
| * back to host from target. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_RETRY_EXHAUSTED: |
| * Optionally used in response, u32 attribute, used in both STA and AP mode. |
| * Value indicates the number of data frames not transmitted successfully even |
| * after retrying the packets for the number of times equal to the total number |
| * of retries allowed for that packet and for which the TX status has been |
| * updated back to host from target. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_TX_TOTAL: |
| * Optionally used in response, u32 attribute, used in AP mode only. |
| * Counter in the target for the number of data frames successfully transmitted |
| * to the station. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_TX_RETRY: |
| * Optionally used in response, u32 attribute, used in AP mode only. |
| * Value indicates the number of data frames successfully transmitted only |
| * after retrying the packets. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_TX_RETRY_EXHAUSTED: |
| * Optionally used in response, u32 attribute, used in both STA & AP mode. |
| * Value indicates the number of data frames not transmitted successfully even |
| * after retrying the packets for the number of times equal to the total number |
| * of retries allowed for that packet. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_PROBE_REQ_BMISS_COUNT: u32, used in |
| * the STA mode only. Represent the number of probe requests sent by the STA |
| * while attempting to roam on missing certain number of beacons from the |
| * connected AP. If queried in the disconnected state, this represents the |
| * count for the last connected state. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_PROBE_RESP_BMISS_COUNT: u32, used in |
| * the STA mode. Represent the number of probe responses received by the station |
| * while attempting to roam on missing certain number of beacons from the |
| * connected AP. When queried in the disconnected state, this represents the |
| * count when in last connected state. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_TX_ALL_COUNT: u32, used in the |
| * STA mode only. Represents the total number of frames sent out by STA |
| * including Data, ACK, RTS, CTS, Control Management. This data is maintained |
| * only for the connect session. Represents the count of last connected session, |
| * when queried in the disconnected state. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_RTS_COUNT: u32, used in the STA mode. |
| * Total number of RTS sent out by the STA. This data is maintained per connect |
| * session. Represents the count of last connected session, when queried in the |
| * disconnected state. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_RTS_RETRY_FAIL_COUNT: u32, used in the |
| * STA mode.Represent the number of RTS transmission failure that reach retry |
| * limit. This data is maintained per connect session. Represents the count of |
| * last connected session, when queried in the disconnected state. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_DATA_NON_AGGREGATED_COUNT: u32, used in |
| * the STA mode. Represent the total number of non aggregated frames transmitted |
| * by the STA. This data is maintained per connect session. Represents the count |
| * of last connected session, when queried in the disconnected state. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_DATA_AGGREGATED_COUNT: u32, used in the |
| * STA mode. Represent the total number of aggregated frames transmitted by the |
| * STA. This data is maintained per connect session. Represents the count of |
| * last connected session, when queried in the disconnected state. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_FRAMES_GOOD_PLCP_COUNT: u32, used in |
| * the STA mode. Represents the number of received frames with a good PLCP. This |
| * data is maintained per connect session. Represents the count of last |
| * connected session, when queried in the disconnected state. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_FRAMES_INVALID_DELIMITER_COUNT: u32, |
| * used in the STA mode. Represents the number of occasions that no valid |
| * delimiter is detected by A-MPDU parser. This data is maintained per connect |
| * session. Represents the count of last connected session, when queried in the |
| * disconnected state. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_FRAMES_CRC_FAIL_COUNT: u32, used in the |
| * STA mode. Represents the number of frames for which CRC check failed in the |
| * MAC. This data is maintained per connect session. Represents the count of |
| * last connected session, when queried in the disconnected state. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_ACKS_GOOD_FCS_COUNT: u32, used in the |
| * STA mode. Represents the number of unicast ACKs received with good FCS. This |
| * data is maintained per connect session. Represents the count of last |
| * connected session, when queried in the disconnected state. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_BLOCKACK_COUNT: u32, used in the STA |
| * mode. Represents the number of received Block Acks. This data is maintained |
| * per connect session. Represents the count of last connected session, when |
| * queried in the disconnected state. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_BEACON_COUNT: u32, used in the STA |
| * mode. Represents the number of beacons received from the connected BSS. This |
| * data is maintained per connect session. Represents the count of last |
| * connected session, when queried in the disconnected state. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_OTHER_BEACON_COUNT: u32, used in the |
| * STA mode. Represents the number of beacons received by the other BSS when in |
| * connected state (through the probes done by the STA). This data is maintained |
| * per connect session. Represents the count of last connected session, when |
| * queried in the disconnected state. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_UCAST_DATA_GOOD_FCS_COUNT: u64, used in |
| * the STA mode. Represents the number of received DATA frames with good FCS and |
| * matching Receiver Address when in connected state. This data is maintained |
| * per connect session. Represents the count of last connected session, when |
| * queried in the disconnected state. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_DATA_BC_MC_DROP_COUNT: u32, used in the |
| * STA mode. Represents the number of RX Data multicast frames dropped by the HW |
| * when in the connected state. This data is maintained per connect session. |
| * Represents the count of last connected session, when queried in the |
| * disconnected state. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_POWER_24G_1MBPS: u32, used in the |
| * STA mode. This represents the target power in dBm for the transmissions done |
| * to the AP in 2.4 GHz at 1 Mbps (DSSS) rate. This data is maintained per |
| * connect session. Represents the count of last connected session, when |
| * queried in the disconnected state. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_POWER_24G_6MBPS: u32, used in the |
| * STA mode. This represents the Target power in dBm for transmissions done to |
| * the AP in 2.4 GHz at 6 Mbps (OFDM) rate. This data is maintained per connect |
| * session. Represents the count of last connected session, when queried in the |
| * disconnected state. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_POWER_24G_MCS0: u32, used in the |
| * STA mode. This represents the Target power in dBm for transmissions done to |
| * the AP in 2.4 GHz at MCS0 rate. This data is maintained per connect session. |
| * Represents the count of last connected session, when queried in the |
| * disconnected state. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_POWER_5G_6MBPS: u32, used in the |
| * STA mode. This represents the Target power in dBm for transmissions done to |
| * the AP in 5 GHz at 6 Mbps (OFDM) rate. This data is maintained per connect |
| * session. Represents the count of last connected session, when queried in |
| * the disconnected state. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_POWER_5G_MCS0: u32, used in the |
| * STA mode. This represents the Target power in dBm for for transmissions done |
| * to the AP in 5 GHz at MCS0 rate. This data is maintained per connect session. |
| * Represents the count of last connected session, when queried in the |
| * disconnected state. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_HW_BUFFERS_OVERFLOW_COUNT: u32, used |
| * in the STA mode. This represents the Nested attribute representing the |
| * overflow counts of each receive buffer allocated to the hardware during the |
| * STA's connection. The number of hw buffers might vary for each WLAN |
| * solution and hence this attribute represents the nested array of all such |
| * HW buffer count. This data is maintained per connect session. Represents |
| * the count of last connected session, when queried in the disconnected state. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_MAX_TX_POWER: u32, Max TX power (dBm) |
| * allowed as per the regulatory requirements for the current or last connected |
| * session. Used in the STA mode. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_LATEST_TX_POWER: u32, Latest TX power |
| * (dBm) used by the station in its latest unicast frame while communicating |
| * to the AP in the connected state. When queried in the disconnected state, |
| * this represents the TX power used by the STA with last AP communication |
| * when in connected state. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_ANI_LEVEL: u32, Adaptive noise immunity |
| * level used to adjust the RX sensitivity. Represents the current ANI level |
| * when queried in the connected state. When queried in the disconnected |
| * state, this corresponds to the latest ANI level at the instance of |
| * disconnection. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_BEACON_IES: Binary attribute containing |
| * the raw information elements from Beacon frames. Represents the Beacon frames |
| * of the current BSS in the connected state. When queried in the disconnected |
| * state, these IEs correspond to the last connected BSSID. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_PROBE_RESP_IES: Binary attribute |
| * containing the raw information elements from Probe Response frames. |
| * Represents the Probe Response frames of the current BSS in the connected |
| * state. When queried in the disconnected state, these IEs correspond to the |
| * last connected BSSID. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_DRIVER_DISCONNECT_REASON: u32, Driver |
| * disconnect reason for the last disconnection if the disconnection is |
| * triggered from the host driver. The values are referred from |
| * enum qca_disconnect_reason_codes. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_BIP_MIC_ERROR_COUNT: u32, used in STA mode |
| * only. This represents the number of group addressed robust management frames |
| * received from this station with an invalid MIC or a missing MME when PMF is |
| * enabled. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_BIP_REPLAY_COUNT: u32, used in STA mode |
| * only. This represents the number of group addressed robust management frames |
| * received from this station with the packet number less than or equal to the |
| * last received packet number when PMF is enabled. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_BEACON_MIC_ERROR_COUNT: u32, used in STA |
| * mode only. This represents the number of Beacon frames received from this |
| * station with an invalid MIC or a missing MME when beacon protection is |
| * enabled. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_BEACON_REPLAY_COUNT: u32, used in STA mode |
| * only. This represents number of Beacon frames received from this station with |
| * the packet number less than or equal to the last received packet number when |
| * beacon protection is enabled. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_CONNECT_FAIL_REASON_CODE: u32, used in |
| * STA mode only. The driver uses this attribute to populate the connection |
| * failure reason codes and the values are defined in |
| * enum qca_sta_connect_fail_reason_codes. Userspace applications can send |
| * QCA_NL80211_VENDOR_SUBCMD_GET_STA_INFO vendor command after receiving |
| * a connection failure indication from the driver. The driver shall not |
| * include this attribute in response to the |
| * QCA_NL80211_VENDOR_SUBCMD_GET_STA_INFO command if there is no connection |
| * failure observed in the last attempted connection. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_LATEST_TX_RATE: u32, latest TX rate (Kbps) |
| * used by the station in its last TX frame while communicating to the AP in the |
| * connected state. When queried in the disconnected state, this represents the |
| * rate used by the STA in the last TX frame to the AP when it was connected. |
| * This attribute is used for STA mode only. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_LATEST_RIX: u32, used in STA mode only. |
| * This represents the rate index used by the STA for the last TX frame to the |
| * AP. When queried in the disconnected state, this gives the last RIX used by |
| * the STA in the last TX frame to the AP when it was connected. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TSF_OUT_OF_SYNC_COUNT: u32, used in STA |
| * mode only. This represents the number of times the STA TSF goes out of sync |
| * from the AP after the connection. If queried in the disconnected state, this |
| * gives the count of TSF out of sync for the last connection. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_ROAM_TRIGGER_REASON: u32, used in STA |
| * mode only. This represents the roam trigger reason for the last roaming |
| * attempted by the firmware. This can be queried either in connected state or |
| * disconnected state. Each bit of this attribute represents the different |
| * roam trigger reason code which are defined in enum qca_vendor_roam_triggers. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_ROAM_FAIL_REASON: u32, used in STA mode |
| * only. This represents the roam fail reason for the last failed roaming |
| * attempt by the firmware. Different roam failure reason codes are specified |
| * in enum qca_vendor_roam_fail_reasons. This can be queried either in |
| * connected state or disconnected state. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_ROAM_INVOKE_FAIL_REASON: u32, used in |
| * STA mode only. This represents the roam invoke fail reason for the last |
| * failed roam invoke. Different roam invoke failure reason codes |
| * are specified in enum qca_vendor_roam_invoke_fail_reasons. This can be |
| * queried either in connected state or disconnected state. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_UPLINK_DELAY: u32, used in STA mode only. |
| * This represents the average congestion duration of uplink frames in MAC |
| * queue in unit of ms. This can be queried either in connected state or |
| * disconnected state. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_PER_MCS_TX_PACKETS: Array of u32 nested |
| * values, used in AP mode. This represents the MPDU packet count per MCS |
| * rate value of TX packets. Every index of this nested attribute corresponds |
| * to MCS index, e.g., Index 0 represents MCS0 TX rate. This can be |
| * queried in connected state. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_PER_MCS_RX_PACKETS: Array of u32 nested |
| * values, used in AP mode. This represents the MPDU packet count per MCS |
| * rate value of RX packets. Every index of this nested attribute corresponds |
| * to MCS index, e.g., Index 0 represents MCS0 RX rate. This can be |
| * queried in connected state. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_PAD: Attribute used for padding for |
| * 64-bit alignment. |
| */ |
| enum qca_wlan_vendor_attr_get_sta_info { |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_MAC = 1, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_FLAGS = 2, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_GUARD_INTERVAL = 3, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_RETRY_COUNT = 4, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_BC_MC_COUNT = 5, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_RETRY_SUCCEED = 6, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_RETRY_EXHAUSTED = 7, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_TX_TOTAL = 8, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_TX_RETRY = 9, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_TX_RETRY_EXHAUSTED = 10, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_PROBE_REQ_BMISS_COUNT = 11, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_PROBE_RESP_BMISS_COUNT = 12, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_TX_ALL_COUNT = 13, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_RTS_COUNT = 14, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_RTS_RETRY_FAIL_COUNT = 15, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_DATA_NON_AGGREGATED_COUNT = 16, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_DATA_AGGREGATED_COUNT = 17, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_FRAMES_GOOD_PLCP_COUNT = 18, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_FRAMES_INVALID_DELIMITER_COUNT = 19, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_FRAMES_CRC_FAIL_COUNT = 20, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_ACKS_GOOD_FCS_COUNT = 21, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_BLOCKACK_COUNT = 22, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_BEACON_COUNT = 23, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_OTHER_BEACON_COUNT = 24, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_UCAST_DATA_GOOD_FCS_COUNT = 25, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_DATA_BC_MC_DROP_COUNT = 26, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_POWER_24G_1MBPS = 27, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_POWER_24G_6MBPS = 28, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_POWER_24G_MCS0 = 29, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_POWER_5G_6MBPS = 30, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_POWER_5G_MCS0 = 31, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_HW_BUFFERS_OVERFLOW_COUNT = 32, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_MAX_TX_POWER = 33, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_LATEST_TX_POWER = 34, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_ANI_LEVEL = 35, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_BEACON_IES = 36, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_PROBE_RESP_IES = 37, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_DRIVER_DISCONNECT_REASON = 38, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_BIP_MIC_ERROR_COUNT = 39, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_BIP_REPLAY_COUNT = 40, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_BEACON_MIC_ERROR_COUNT = 41, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_BEACON_REPLAY_COUNT = 42, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_CONNECT_FAIL_REASON_CODE = 43, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_LATEST_TX_RATE = 44, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_LATEST_RIX = 45, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TSF_OUT_OF_SYNC_COUNT = 46, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_ROAM_TRIGGER_REASON = 47, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_ROAM_FAIL_REASON = 48, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_ROAM_INVOKE_FAIL_REASON = 49, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_UPLINK_DELAY = 50, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_PER_MCS_TX_PACKETS = 51, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_PER_MCS_RX_PACKETS = 52, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_PAD = 53, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_MAX = |
| QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_update_sta_info - Defines attributes |
| * used by QCA_NL80211_VENDOR_SUBCMD_UPDATE_STA_INFO vendor command. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_UPDATE_STA_INFO_CONNECT_CHANNELS: Type is NLA_UNSPEC. |
| * Used in STA mode. This attribute represents the list of channel center |
| * frequencies in MHz (u32) the station has learnt during the last connection |
| * or roaming attempt. This information shall not signify the channels for |
| * an explicit scan request from the user space. Host drivers can update this |
| * information to the user space in both connected and disconnected state. |
| * In the disconnected state this information shall signify the channels |
| * scanned in the last connection/roam attempt that lead to the disconnection. |
| */ |
| enum qca_wlan_vendor_attr_update_sta_info { |
| QCA_WLAN_VENDOR_ATTR_UPDATE_STA_INFO_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_UPDATE_STA_INFO_CONNECT_CHANNELS = 1, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_UPDATE_STA_INFO_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_UPDATE_STA_INFO_MAX = |
| QCA_WLAN_VENDOR_ATTR_UPDATE_STA_INFO_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_disconnect_reason_codes - Specifies driver disconnect reason codes. |
| * Used when the driver triggers the STA to disconnect from the AP. |
| * |
| * @QCA_DISCONNECT_REASON_UNSPECIFIED: The host driver triggered the |
| * disconnection with the AP due to unspecified reasons. |
| * |
| * @QCA_DISCONNECT_REASON_INTERNAL_ROAM_FAILURE: The host driver triggered the |
| * disconnection with the AP due to a roaming failure. This roaming is triggered |
| * internally (host driver/firmware). |
| * |
| * @QCA_DISCONNECT_REASON_EXTERNAL_ROAM_FAILURE: The driver disconnected from |
| * the AP when the user/external triggered roaming fails. |
| * |
| * @QCA_DISCONNECT_REASON_GATEWAY_REACHABILITY_FAILURE: This reason code is used |
| * by the host driver whenever gateway reachability failure is detected and the |
| * driver disconnects with AP. |
| * |
| * @QCA_DISCONNECT_REASON_UNSUPPORTED_CHANNEL_CSA: The driver disconnected from |
| * the AP on a channel switch announcement from it with an unsupported channel. |
| * |
| * @QCA_DISCONNECT_REASON_OPER_CHANNEL_DISABLED_INDOOR: On a concurrent AP start |
| * with indoor channels disabled and if the STA is connected on one of these |
| * disabled channels, the host driver disconnected the STA with this reason |
| * code. |
| * |
| * @QCA_DISCONNECT_REASON_OPER_CHANNEL_USER_DISABLED: Disconnection due to an |
| * explicit request from the user to disable the current operating channel. |
| * |
| * @QCA_DISCONNECT_REASON_DEVICE_RECOVERY: STA disconnected from the AP due to |
| * the internal host driver/firmware recovery. |
| * |
| * @QCA_DISCONNECT_REASON_KEY_TIMEOUT: The driver triggered the disconnection on |
| * a timeout for the key installations from the user space. |
| * |
| * @QCA_DISCONNECT_REASON_OPER_CHANNEL_BAND_CHANGE: The dDriver disconnected the |
| * STA on a band change request from the user space to a different band from the |
| * current operation channel/band. |
| * |
| * @QCA_DISCONNECT_REASON_IFACE_DOWN: The STA disconnected from the AP on an |
| * interface down trigger from the user space. |
| * |
| * @QCA_DISCONNECT_REASON_PEER_XRETRY_FAIL: The host driver disconnected the |
| * STA on getting continuous transmission failures for multiple Data frames. |
| * |
| * @QCA_DISCONNECT_REASON_PEER_INACTIVITY: The STA does a keep alive |
| * notification to the AP by transmitting NULL/G-ARP frames. This disconnection |
| * represents inactivity from AP on such transmissions. |
| |
| * @QCA_DISCONNECT_REASON_SA_QUERY_TIMEOUT: This reason code is used on |
| * disconnection when SA Query times out (AP does not respond to SA Query). |
| * |
| * @QCA_DISCONNECT_REASON_BEACON_MISS_FAILURE: The host driver disconnected the |
| * STA on missing the beacons continuously from the AP. |
| * |
| * @QCA_DISCONNECT_REASON_CHANNEL_SWITCH_FAILURE: Disconnection due to STA not |
| * able to move to the channel mentioned by the AP in CSA. |
| * |
| * @QCA_DISCONNECT_REASON_USER_TRIGGERED: User triggered disconnection. |
| */ |
| enum qca_disconnect_reason_codes { |
| QCA_DISCONNECT_REASON_UNSPECIFIED = 0, |
| QCA_DISCONNECT_REASON_INTERNAL_ROAM_FAILURE = 1, |
| QCA_DISCONNECT_REASON_EXTERNAL_ROAM_FAILURE = 2, |
| QCA_DISCONNECT_REASON_GATEWAY_REACHABILITY_FAILURE = 3, |
| QCA_DISCONNECT_REASON_UNSUPPORTED_CHANNEL_CSA = 4, |
| QCA_DISCONNECT_REASON_OPER_CHANNEL_DISABLED_INDOOR = 5, |
| QCA_DISCONNECT_REASON_OPER_CHANNEL_USER_DISABLED = 6, |
| QCA_DISCONNECT_REASON_DEVICE_RECOVERY = 7, |
| QCA_DISCONNECT_REASON_KEY_TIMEOUT = 8, |
| QCA_DISCONNECT_REASON_OPER_CHANNEL_BAND_CHANGE = 9, |
| QCA_DISCONNECT_REASON_IFACE_DOWN = 10, |
| QCA_DISCONNECT_REASON_PEER_XRETRY_FAIL = 11, |
| QCA_DISCONNECT_REASON_PEER_INACTIVITY = 12, |
| QCA_DISCONNECT_REASON_SA_QUERY_TIMEOUT = 13, |
| QCA_DISCONNECT_REASON_BEACON_MISS_FAILURE = 14, |
| QCA_DISCONNECT_REASON_CHANNEL_SWITCH_FAILURE = 15, |
| QCA_DISCONNECT_REASON_USER_TRIGGERED = 16, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_driver_disconnect_reason - Defines attributes |
| * used by %QCA_NL80211_VENDOR_SUBCMD_DRIVER_DISCONNECT_REASON vendor command. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_DRIVER_DISCONNECT_REASCON_CODE: u32 attribute. |
| * This attribute represents the driver specific reason codes (local |
| * driver/firmware initiated reasons for disconnection) defined |
| * in enum qca_disconnect_reason_codes. |
| */ |
| enum qca_wlan_vendor_attr_driver_disconnect_reason { |
| QCA_WLAN_VENDOR_ATTR_DRIVER_DISCONNECT_REASON_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_DRIVER_DISCONNECT_REASCON_CODE = 1, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_DRIVER_DISCONNECT_REASON_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_DRIVER_DISCONNECT_REASON_MAX = |
| QCA_WLAN_VENDOR_ATTR_DRIVER_DISCONNECT_REASON_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_tspec_operation - Operation of the config TSPEC request |
| * |
| * Values for %QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_OPERATION. |
| */ |
| enum qca_wlan_tspec_operation { |
| QCA_WLAN_TSPEC_ADD = 0, |
| QCA_WLAN_TSPEC_DEL = 1, |
| QCA_WLAN_TSPEC_GET = 2, |
| }; |
| |
| /** |
| * enum qca_wlan_tspec_direction - Direction in TSPEC |
| * As what is defined in IEEE Std 802.11-2016, Table 9-139. |
| * |
| * Values for %QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_DIRECTION. |
| */ |
| enum qca_wlan_tspec_direction { |
| QCA_WLAN_TSPEC_DIRECTION_UPLINK = 0, |
| QCA_WLAN_TSPEC_DIRECTION_DOWNLINK = 1, |
| QCA_WLAN_TSPEC_DIRECTION_DIRECT = 2, |
| QCA_WLAN_TSPEC_DIRECTION_BOTH = 3, |
| }; |
| |
| /** |
| * enum qca_wlan_tspec_ack_policy - MAC acknowledgement policy in TSPEC |
| * As what is defined in IEEE Std 802.11-2016, Table 9-141. |
| * |
| * Values for %QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_ACK_POLICY. |
| */ |
| enum qca_wlan_tspec_ack_policy { |
| QCA_WLAN_TSPEC_NORMAL_ACK = 0, |
| QCA_WLAN_TSPEC_NO_ACK = 1, |
| /* Reserved */ |
| QCA_WLAN_TSPEC_BLOCK_ACK = 3, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_config_tspec - Defines attributes |
| * used by %QCA_NL80211_VENDOR_SUBCMD_CONFIG_TSPEC vendor command. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_OPERATION: |
| * u8 attribute. Specify the TSPEC operation of this request. Possible values |
| * are defined in enum qca_wlan_tspec_operation. |
| * Mandatory attribute for all kinds of config TSPEC requests. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_TSID: |
| * u8 attribute. TS ID. Possible values are 0-7. |
| * Applicable for operation: QCA_WLAN_TSPEC_ADD, QCA_WLAN_TSPEC_DEL, |
| * QCA_WLAN_TSPEC_GET. A mandatory attribute. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_DIRECTION: |
| * u8 attribute. Direction of data carried by the TS. Possible values are |
| * defined in enum qca_wlan_tspec_direction. |
| * Applicable for operation: QCA_WLAN_TSPEC_ADD. A mandatory attribute. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_APSD: |
| * Flag attribute. Indicate whether APSD is enabled for the traffic associated |
| * with the TS. set - enabled, not set - disabled. |
| * Applicable for operation: QCA_WLAN_TSPEC_ADD. A mandatory attribute. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_USER_PRIORITY: |
| * u8 attribute. User priority to be used for the transport of MSDUs/A-MSDUs |
| * belonging to this TS. Possible values are 0-7. |
| * Applicable for operation: QCA_WLAN_TSPEC_ADD. An optional attribute. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_ACK_POLICY: |
| * u8 attribute. Indicate whether MAC acknowledgements are required for |
| * MPDUs/A-MSDUs belonging to this TS and the form of those acknowledgements. |
| * Possible values are defined in enum qca_wlan_tspec_ack_policy. |
| * Applicable for operation: QCA_WLAN_TSPEC_ADD. A mandatory attribute. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_NOMINAL_MSDU_SIZE: |
| * u16 attribute. Specify the nominal size in bytes of MSDUs/A-MSDUs |
| * belonging to this TS. |
| * Applicable for operation: QCA_WLAN_TSPEC_ADD. A mandatory attribute. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_MAXIMUM_MSDU_SIZE: |
| * u16 attribute. Specify the maximum size in bytes of MSDUs/A-MSDUs |
| * belonging to this TS. |
| * Applicable for operation: QCA_WLAN_TSPEC_ADD. A mandatory attribute. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_MIN_SERVICE_INTERVAL: |
| * u32 attribute. Specify the minimum interval in microseconds between the |
| * start of two successive SPs. |
| * Applicable for operation: QCA_WLAN_TSPEC_ADD. A mandatory attribute. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_MAX_SERVICE_INTERVAL: |
| * u32 attribute. Specify the maximum interval in microseconds between the |
| * start of two successive SPs. |
| * Applicable for operation: QCA_WLAN_TSPEC_ADD. A mandatory attribute. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_INACTIVITY_INTERVAL: |
| * u32 attribute. Specify the minimum interval in microseconds that can elapse |
| * without arrival or transfer of an MPDU belonging to the TS before this TS |
| * is deleted by the MAC entity at the HC. |
| * Applicable for operation: QCA_WLAN_TSPEC_ADD. A mandatory attribute. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_SUSPENSION_INTERVAL: |
| * u32 attribute. Specify the minimum interval in microseconds that can elapse |
| * without arrival or transfer of an MSDU belonging to the TS before the |
| * generation of successive QoS(+)CF-Poll is stopped for this TS. A value of |
| * 0xFFFFFFFF disables the suspension interval. The value of the suspension |
| * interval is always less than or equal to the inactivity interval. |
| * Applicable for operation: QCA_WLAN_TSPEC_ADD. A mandatory attribute. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_MINIMUM_DATA_RATE: |
| * u32 attribute. Indicate the lowest data rate in bps specified at the MAC |
| * SAP for transport of MSDUs or A-MSDUs belonging to this TS within the |
| * bounds of this TSPEC. |
| * Applicable for operation: QCA_WLAN_TSPEC_ADD. An optional attribute. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_MEAN_DATA_RATE: |
| * u32 attribute. Indicate the average data rate in bps specified at the MAC |
| * SAP for transport of MSDUs or A-MSDUs belonging to this TS within the |
| * bounds of this TSPEC. |
| * Applicable for operation: QCA_WLAN_TSPEC_ADD. An optional attribute. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_PEAK_DATA_RATE: |
| * u32 attribute. Indicate the maximum allowable data rate in bps specified at |
| * the MAC SAP for transport of MSDUs or A-MSDUs belonging to this TS within |
| * the bounds of this TSPEC. |
| * Applicable for operation: QCA_WLAN_TSPEC_ADD. An optional attribute. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_BURST_SIZE: |
| * u32 attribute. Specify the maximum burst size in bytes of the MSDUs/A-MSDUs |
| * belonging to this TS that arrive at the MAC SAP at the peak data rate. A |
| * value of 0 indicates that there are no bursts. |
| * Applicable for operation: QCA_WLAN_TSPEC_ADD. An optional attribute. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_MINIMUM_PHY_RATE: |
| * u32 attribute. Indicate the minimum PHY rate in bps for transport of |
| * MSDUs/A-MSDUs belonging to this TS within the bounds of this TSPEC. |
| * Applicable for operation: QCA_WLAN_TSPEC_ADD. An optional attribute. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_SURPLUS_BANDWIDTH_ALLOWANCE: |
| * u16 attribute. Specify the excess allocation of time (and bandwidth) over |
| * and above the stated application rates required to transport an MSDU/A-MSDU |
| * belonging to the TS in this TSPEC. |
| * Applicable for operation: QCA_WLAN_TSPEC_ADD. A mandatory attribute. |
| */ |
| enum qca_wlan_vendor_attr_config_tspec { |
| QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_OPERATION = 1, |
| QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_TSID = 2, |
| QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_DIRECTION = 3, |
| QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_APSD = 4, |
| QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_USER_PRIORITY = 5, |
| QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_ACK_POLICY = 6, |
| QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_NOMINAL_MSDU_SIZE = 7, |
| QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_MAXIMUM_MSDU_SIZE = 8, |
| QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_MIN_SERVICE_INTERVAL = 9, |
| QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_MAX_SERVICE_INTERVAL = 10, |
| QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_INACTIVITY_INTERVAL = 11, |
| QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_SUSPENSION_INTERVAL = 12, |
| QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_MINIMUM_DATA_RATE = 13, |
| QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_MEAN_DATA_RATE = 14, |
| QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_PEAK_DATA_RATE = 15, |
| QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_BURST_SIZE = 16, |
| QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_MINIMUM_PHY_RATE = 17, |
| QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_SURPLUS_BANDWIDTH_ALLOWANCE = 18, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_MAX = |
| QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_oci_override_frame_type - OCI override frame type |
| * @QCA_WLAN_VENDOR_OCI_OVERRIDE_FRAME_SA_QUERY_REQ: SA Query Request frame |
| * @QCA_WLAN_VENDOR_OCI_OVERRIDE_FRAME_SA_QUERY_RESP: SA Query Response frame |
| * @QCA_WLAN_VENDOR_OCI_OVERRIDE_FRAME_FT_REASSOC_REQ: FT Reassociation Request |
| * frame |
| * @QCA_WLAN_VENDOR_OCI_OVERRIDE_FRAME_FILS_REASSOC_REQ: FILS Reassociation |
| * Request frame. |
| */ |
| enum qca_wlan_vendor_oci_override_frame_type { |
| QCA_WLAN_VENDOR_OCI_OVERRIDE_FRAME_SA_QUERY_REQ = 1, |
| QCA_WLAN_VENDOR_OCI_OVERRIDE_FRAME_SA_QUERY_RESP = 2, |
| QCA_WLAN_VENDOR_OCI_OVERRIDE_FRAME_FT_REASSOC_REQ = 3, |
| QCA_WLAN_VENDOR_OCI_OVERRIDE_FRAME_FILS_REASSOC_REQ = 4, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_oci_override: Represents attributes for |
| * OCI override request. These attributes are used inside nested attribute |
| * %QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_OCI_OVERRIDE in QCA vendor command |
| * %QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_OCI_OVERRIDE_FRAME_TYPE: Required attribute, u8. |
| * Values from enum qca_wlan_vendor_oci_override_frame_type used in this |
| * attribute to specify the frame type in which the OCI is to be overridden. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_OCI_OVERRIDE_FREQUENCY: Required (u32) |
| * OCI frequency (in MHz) to override in the specified frame type. |
| */ |
| enum qca_wlan_vendor_attr_oci_override { |
| QCA_WLAN_VENDOR_ATTR_OCI_OVERRIDE_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_OCI_OVERRIDE_FRAME_TYPE = 1, |
| QCA_WLAN_VENDOR_ATTR_OCI_OVERRIDE_FREQUENCY = 2, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_OCI_OVERRIDE_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_OCI_OVERRIDE_MAX = |
| QCA_WLAN_VENDOR_ATTR_OCI_OVERRIDE_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_medium_assess_type - Type of medium assess request |
| * |
| * Values for %QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_TYPE. |
| */ |
| enum qca_wlan_medium_assess_type { |
| QCA_WLAN_MEDIUM_ASSESS_CCA = 0, |
| QCA_WLAN_MEDIUM_ASSESS_CONGESTION_REPORT = 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_medium_assess - Attributes used by |
| * %QCA_NL80211_VENDOR_SUBCMD_MEDIUM_ASSESS vendor command. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_TYPE: |
| * u8 attribute. Mandatory in all kinds of medium assess requests/responses. |
| * Specify the type of medium assess request and indicate its type in response. |
| * Possible values are defined in enum qca_wlan_medium_assess_type. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_PERIOD: |
| * u32 attribute. Mandatory in CCA request. |
| * Specify the assessment period in terms of seconds. Assessment result will be |
| * sent as the response to the CCA request after the assessment period. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_TOTAL_CYCLE_COUNT: |
| * u32 attribute. Mandatory in response to CCA request. |
| * Total timer tick count of the assessment cycle. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_IDLE_COUNT: |
| * u32 attribute. Mandatory in response to CCA request. |
| * Timer tick count of idle time in the assessment cycle. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_IBSS_RX_COUNT: |
| * u32 attribute. Mandatory in response to CCA request. |
| * Timer tick count of Intra BSS traffic RX time in the assessment cycle. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_OBSS_RX_COUNT: |
| * u32 attribute. Mandatory in response to CCA request. |
| * Timer tick count of Overlapping BSS traffic RX time in the assessment cycle. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_MAX_IBSS_RSSI: |
| * s32 attribute. Mandatory in response to CCA request. |
| * Maximum RSSI of Intra BSS traffic in the assessment cycle. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_MIN_IBSS_RSSI: |
| * s32 attribute. Mandatory in response to CCA request. |
| * Minimum RSSI of Intra BSS traffic in the assessment cycle. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_CONGESTION_REPORT_ENABLE: |
| * u8 attribute. Mandatory in congestion report request. |
| * 1-enable 0-disable. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_CONGESTION_REPORT_THRESHOLD: |
| * u8 attribute. Mandatory in congestion report enable request and will be |
| * ignored if present in congestion report disable request. Possible values are |
| * 0-100. A vendor event QCA_NL80211_VENDOR_SUBCMD_MEDIUM_ASSESS with the type |
| * QCA_WLAN_MEDIUM_ASSESS_CONGESTION_REPORT will be sent to userspace if |
| * congestion percentage reaches the configured threshold. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_CONGESTION_REPORT_INTERVAL: |
| * u8 attribute. Optional in congestion report enable request and will be |
| * ignored if present in congestion report disable request. |
| * Specify the interval of congestion report event in terms of seconds. Possible |
| * values are 1-255. Default value 1 will be used if this attribute is omitted |
| * or using invalid values. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_CONGESTION_PERCENTAGE: |
| * u8 attribute. Mandatory in congestion report event. |
| * Indicate the actual congestion percentage. Possible values are 0-100. |
| */ |
| enum qca_wlan_vendor_attr_medium_assess { |
| QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_TYPE = 1, |
| |
| QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_PERIOD = 2, |
| QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_TOTAL_CYCLE_COUNT = 3, |
| QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_IDLE_COUNT = 4, |
| QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_IBSS_RX_COUNT = 5, |
| QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_OBSS_RX_COUNT = 6, |
| QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_MAX_IBSS_RSSI = 7, |
| QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_MIN_IBSS_RSSI = 8, |
| |
| QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_CONGESTION_REPORT_ENABLE = 9, |
| QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_CONGESTION_REPORT_THRESHOLD = 10, |
| QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_CONGESTION_REPORT_INTERVAL = 11, |
| QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_CONGESTION_PERCENTAGE = 12, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_MAX = |
| QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_mbssid_tx_vdev_status - Defines attributes |
| * used by QCA_NL80211_VENDOR_SUBCMD_MBSSID_TX_VDEV_STATUS vendor command. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_STATUS_VAL: |
| * u8 attribute. Notify the TX VDEV status. Possible values 0, 1 |
| * belonging to MBSSID/EMA_AP configuration. 0 means Non-Tx VDEV, |
| * 1 means Tx VDEV. Mandatory attribute for all MBSSID VDEV status events. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_EVENT: |
| * u8 attribute, required. 1 means Tx VDEV up event. 0 means Tx VDEV down event. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_GROUP_ID: |
| * u8 attribute, required. Indicates group id of Tx VDEV. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_GROUP_INFO: |
| * Nested attribute. This attribute shall be used by the driver to send |
| * group information. The attributes defined in enum |
| * qca_wlan_vendor_attr_mbssid_tx_vdev_group_info |
| * are nested in this attribute. |
| */ |
| enum qca_wlan_vendor_attr_mbssid_tx_vdev_status { |
| QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_STATUS_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_STATUS_VAL = 1, |
| QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_EVENT = 2, |
| QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_GROUP_ID = 3, |
| QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_GROUP_INFO = 4, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_STATUS_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_STATUS_MAX = |
| QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_STATUS_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_mbssid_tx_vdev_group_info - Attributes used |
| * inside %QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_GROUP_INFO nested attribute. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_GROUP_INFO_IF_INDEX: |
| * u32 attribute, required. Contains interface index. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_GROUP_INFO_STATUS: |
| * u8 attribute, required. 0 - means vdev is in down state. |
| * 1 - means vdev is in up state. |
| */ |
| enum qca_wlan_vendor_attr_mbssid_tx_vdev_group_info { |
| QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_GROUP_INFO_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_GROUP_INFO_IF_INDEX = 1, |
| QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_GROUP_INFO_STATUS = 2, |
| |
| QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_GROUP_INFO_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_GROUP_INFO_MAX = |
| QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_GROUP_INFO - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_concurrent_sta_policy_config - Concurrent STA policies |
| * |
| * @QCA_WLAN_CONCURRENT_STA_POLICY_PREFER_PRIMARY: Preference to the primary |
| * STA interface has to be given while selecting the connection policies |
| * (e.g., BSSID, band, TX/RX chains, etc.) for the subsequent STA interface. |
| * An interface is set as primary through the attribute |
| * QCA_WLAN_VENDOR_ATTR_CONFIG_CONCURRENT_STA_PRIMARY. This policy is not |
| * applicable if the primary interface has not been set earlier. |
| * |
| * The intention is not to downgrade the primary STA performance, such as: |
| * - Do not reduce the number of TX/RX chains of primary connection. |
| * - Do not optimize DBS vs. MCC/SCC, if DBS ends up reducing the number of |
| * chains. |
| * - If using MCC, should set the MCC duty cycle of the primary connection to |
| * be higher than the secondary connection. |
| * |
| * @QCA_WLAN_CONCURRENT_STA_POLICY_UNBIASED: The connection policies for the |
| * subsequent STA connection shall be chosen to balance with the existing |
| * concurrent STA's performance. |
| * Such as |
| * - Can choose MCC or DBS mode depending on the MCC efficiency and hardware |
| * capability. |
| * - If using MCC, set the MCC duty cycle of the primary connection to be equal |
| * to the secondary. |
| * - Prefer BSSID candidates which will help provide the best "overall" |
| * performance for all the STA connections. |
| */ |
| enum qca_wlan_concurrent_sta_policy_config { |
| QCA_WLAN_CONCURRENT_STA_POLICY_PREFER_PRIMARY = 0, |
| QCA_WLAN_CONCURRENT_STA_POLICY_UNBIASED = 1, |
| }; |
| |
| /** |
| * enum qca_wlan_concurrent_ap_policy_config - Concurrent AP policies |
| * |
| * @QCA_WLAN_CONCURRENT_AP_POLICY_UNSPECIFIED: No specific policy for this AP |
| * interface. |
| * |
| * @QCA_WLAN_CONCURRENT_AP_POLICY_GAMING_AUDIO: Select interface concurrencies |
| * to meet gaming audio latency requirements. |
| * This policy is used only when the driver advertises support for |
| * QCA_WLAN_VENDOR_FEATURE_ENHANCED_AUDIO_EXPERIENCE_OVER_WLAN. |
| * |
| * @QCA_WLAN_CONCURRENT_AP_POLICY_LOSSLESS_AUDIO_STREAMING: Select interface |
| * concurrencies to meet lossless audio streaming requirements. |
| * This policy is used only when the driver advertises support for |
| * QCA_WLAN_VENDOR_FEATURE_ENHANCED_AUDIO_EXPERIENCE_OVER_WLAN. |
| * |
| * @QCA_WLAN_CONCURRENT_AP_POLICY_XR: Select interface concurrencies to meet |
| * XR (eXtended Reality) requirements. |
| */ |
| enum qca_wlan_concurrent_ap_policy_config { |
| QCA_WLAN_CONCURRENT_AP_POLICY_UNSPECIFIED = 0, |
| QCA_WLAN_CONCURRENT_AP_POLICY_GAMING_AUDIO = 1, |
| QCA_WLAN_CONCURRENT_AP_POLICY_LOSSLESS_AUDIO_STREAMING = 2, |
| QCA_WLAN_CONCURRENT_AP_POLICY_XR = 3, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_concurrent_policy - Defines attributes |
| * used by QCA_NL80211_VENDOR_SUBCMD_CONCURRENT_POLICY vendor command. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_CONCURRENT_POLICY_STA_CONFIG: |
| * u8 attribute. Configures the concurrent STA policy configuration. |
| * Possible values are defined in enum qca_wlan_concurrent_sta_policy_config. |
| |
| * @QCA_WLAN_VENDOR_ATTR_CONCURRENT_POLICY_AP_CONFIG: |
| * u8 attribute. Configures the concurrent AP policy configuration. |
| * Possible values are defined in enum qca_wlan_concurrent_ap_policy_config. |
| */ |
| enum qca_wlan_vendor_attr_concurrent_policy { |
| QCA_WLAN_VENDOR_ATTR_CONCURRENT_POLICY_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_CONCURRENT_POLICY_STA_CONFIG = 1, |
| QCA_WLAN_VENDOR_ATTR_CONCURRENT_POLICY_AP_CONFIG = 2, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_CONCURRENT_POLICY_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_CONCURRENT_POLICY_MAX = |
| QCA_WLAN_VENDOR_ATTR_CONCURRENT_POLICY_AFTER_LAST - 1, |
| |
| }; |
| |
| /* Compatibility defines for previously used enum |
| * qca_wlan_vendor_attr_concurrent_policy names. These values should not be used |
| * in any new implementation. |
| */ |
| #define QCA_WLAN_VENDOR_ATTR_CONCURRENT_STA_POLICY_CONFIG \ |
| QCA_WLAN_VENDOR_ATTR_CONCURRENT_POLICY_STA_CONFIG |
| #define QCA_WLAN_VENDOR_ATTR_CONCURRENT_STA_POLICY_MAX \ |
| QCA_WLAN_VENDOR_ATTR_CONCURRENT_POLICY_MAX |
| #define qca_wlan_vendor_attr_concurrent_sta_policy \ |
| qca_wlan_vendor_attr_concurrent_policy |
| |
| /** |
| * enum qca_sta_connect_fail_reason_codes - Defines values carried |
| * by QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_CONNECT_FAIL_REASON_CODE vendor |
| * attribute. |
| * @QCA_STA_CONNECT_FAIL_REASON_NO_BSS_FOUND: No Probe Response frame received |
| * for unicast Probe Request frame. |
| * @QCA_STA_CONNECT_FAIL_REASON_AUTH_TX_FAIL: STA failed to send auth request. |
| * @QCA_STA_CONNECT_FAIL_REASON_AUTH_NO_ACK_RECEIVED: AP didn't send ACK for |
| * auth request. |
| * @QCA_STA_CONNECT_FAIL_REASON_AUTH_NO_RESP_RECEIVED: Auth response is not |
| * received from AP. |
| * @QCA_STA_CONNECT_FAIL_REASON_ASSOC_REQ_TX_FAIL: STA failed to send |
| * Association Request frame. |
| * @QCA_STA_CONNECT_FAIL_REASON_ASSOC_NO_ACK_RECEIVED: AP didn't send ACK for |
| * Association Request frame. |
| * @QCA_STA_CONNECT_FAIL_REASON_ASSOC_NO_RESP_RECEIVED: Association Response |
| * frame is not received from AP. |
| */ |
| enum qca_sta_connect_fail_reason_codes { |
| QCA_STA_CONNECT_FAIL_REASON_NO_BSS_FOUND = 1, |
| QCA_STA_CONNECT_FAIL_REASON_AUTH_TX_FAIL = 2, |
| QCA_STA_CONNECT_FAIL_REASON_AUTH_NO_ACK_RECEIVED = 3, |
| QCA_STA_CONNECT_FAIL_REASON_AUTH_NO_RESP_RECEIVED = 4, |
| QCA_STA_CONNECT_FAIL_REASON_ASSOC_REQ_TX_FAIL = 5, |
| QCA_STA_CONNECT_FAIL_REASON_ASSOC_NO_ACK_RECEIVED = 6, |
| QCA_STA_CONNECT_FAIL_REASON_ASSOC_NO_RESP_RECEIVED = 7, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_usable_channels_filter - Bitmask of different |
| * filters defined in this enum are used in attribute |
| * %QCA_WLAN_VENDOR_ATTR_USABLE_CHANNELS_FILTER_MASK. |
| * |
| * @QCA_WLAN_VENDOR_FILTER_CELLULAR_COEX: When this bit is set, the driver |
| * shall filter the channels which are not usable because of coexistence with |
| * cellular radio. |
| * @QCA_WLAN_VENDOR_FILTER_WLAN_CONCURRENCY: When this bit is set, the driver |
| * shall filter the channels which are not usable because of existing active |
| * interfaces in the driver and will result in Multi Channel Concurrency, etc. |
| * |
| */ |
| enum qca_wlan_vendor_usable_channels_filter { |
| QCA_WLAN_VENDOR_FILTER_CELLULAR_COEX = 0, |
| QCA_WLAN_VENDOR_FILTER_WLAN_CONCURRENCY = 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_chan_info - Attributes used inside |
| * %QCA_WLAN_VENDOR_ATTR_USABLE_CHANNELS_CHAN_INFO nested attribute. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_CHAN_INFO_PRIMARY_FREQ: |
| * u32 attribute, required. Indicates the center frequency of the primary |
| * channel in MHz. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_CHAN_INFO_SEG0_FREQ: |
| * u32 attribute. Indicates the center frequency of the primary segment of the |
| * channel in MHz. This attribute is required when reporting 40 MHz, 80 MHz, |
| * 160 MHz, and 320 MHz channels. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_CHAN_INFO_SEG1_FREQ: |
| * u32 attribute. Indicates the center frequency of the secondary segment of |
| * 80+80 channel in MHz. This attribute is required only when |
| * QCA_WLAN_VENDOR_ATTR_CHAN_INFO_BANDWIDTH is set to NL80211_CHAN_WIDTH_80P80. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_CHAN_INFO_BANDWIDTH: |
| * u32 attribute, required. Indicates the bandwidth of the channel, possible |
| * values are defined in enum nl80211_chan_width. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_CHAN_INFO_IFACE_MODE_MASK: |
| * u32 attribute, required. Indicates all the interface types for which this |
| * channel is usable. This attribute encapsulates bitmasks of interface types |
| * defined in enum nl80211_iftype. |
| * |
| */ |
| enum qca_wlan_vendor_attr_chan_info { |
| QCA_WLAN_VENDOR_ATTR_CHAN_INFO_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_CHAN_INFO_PRIMARY_FREQ = 1, |
| QCA_WLAN_VENDOR_ATTR_CHAN_INFO_SEG0_FREQ = 2, |
| QCA_WLAN_VENDOR_ATTR_CHAN_INFO_SEG1_FREQ = 3, |
| QCA_WLAN_VENDOR_ATTR_CHAN_INFO_BANDWIDTH = 4, |
| QCA_WLAN_VENDOR_ATTR_CHAN_INFO_IFACE_MODE_MASK = 5, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_CHAN_INFO_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_CHAN_INFO_MAX = |
| QCA_WLAN_VENDOR_ATTR_CHAN_INFO_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_usable_channels - Attributes used by |
| * %QCA_NL80211_VENDOR_SUBCMD_USABLE_CHANNELS vendor command. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_USABLE_CHANNELS_BAND_MASK: |
| * u32 attribute. Indicates the bands from which the channels should be reported |
| * in response. This attribute encapsulates bit masks of bands defined in enum |
| * nl80211_band. Optional attribute, if not present in the request the driver |
| * shall return channels from all supported bands. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_USABLE_CHANNELS_IFACE_MODE_MASK: |
| * u32 attribute. Indicates all the interface types for which the usable |
| * channels information is requested. This attribute encapsulates bitmasks of |
| * interface types defined in enum nl80211_iftype. Optional attribute, if not |
| * present in the request the driver shall send information of all supported |
| * interface modes. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_USABLE_CHANNELS_FILTER_MASK: |
| * u32 attribute. This attribute carries information of all filters that shall |
| * be applied while populating usable channels information by the driver. This |
| * attribute carries bit masks of different filters defined in enum |
| * qca_wlan_vendor_usable_channels_filter. Optional attribute, if not present |
| * in the request the driver shall send information of channels without applying |
| * any of the filters that can be configured through this attribute. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_USABLE_CHANNELS_CHAN_INFO: |
| * Nested attribute. This attribute shall be used by the driver to send |
| * usability information of each channel. The attributes defined in enum |
| * qca_wlan_vendor_attr_chan_info are used inside this attribute. |
| */ |
| enum qca_wlan_vendor_attr_usable_channels { |
| QCA_WLAN_VENDOR_ATTR_USABLE_CHANNELS_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_USABLE_CHANNELS_BAND_MASK = 1, |
| QCA_WLAN_VENDOR_ATTR_USABLE_CHANNELS_IFACE_MODE_MASK = 2, |
| QCA_WLAN_VENDOR_ATTR_USABLE_CHANNELS_FILTER_MASK = 3, |
| QCA_WLAN_VENDOR_ATTR_USABLE_CHANNELS_CHAN_INFO = 4, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_USABLE_CHANNELS_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_USABLE_CHANNELS_MAX = |
| QCA_WLAN_VENDOR_ATTR_USABLE_CHANNELS_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_radar_history: Used by the vendor command |
| * QCA_NL80211_VENDOR_SUBCMD_GET_RADAR_HISTORY to get DFS radar history. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_RADAR_HISTORY_ENTRIES: Nested attribute to carry |
| * the list of radar history entries. |
| * Each entry contains freq, timestamp, and radar signal detect flag. |
| * The driver shall add an entry when CAC has finished, or radar signal |
| * has been detected post AP beaconing. The driver shall maintain at least |
| * 8 entries in order to save CAC result for a 160 MHz channel. |
| * @QCA_WLAN_VENDOR_ATTR_RADAR_HISTORY_FREQ: u32 attribute. |
| * Channel frequency in MHz. |
| * @QCA_WLAN_VENDOR_ATTR_RADAR_HISTORY_TIMESTAMP: u64 nanoseconds. |
| * CLOCK_BOOTTIME timestamp when this entry is updated due to CAC |
| * or radar detection. |
| * @QCA_WLAN_VENDOR_ATTR_RADAR_HISTORY_DETECTED: NLA_FLAG attribute. |
| * This flag indicates radar signal has been detected. |
| * @QCA_WLAN_VENDOR_ATTR_RADAR_HISTORY_PAD: Attribute used for padding for |
| * 64-bit alignment. |
| */ |
| enum qca_wlan_vendor_attr_radar_history { |
| QCA_WLAN_VENDOR_ATTR_RADAR_HISTORY_INVALID = 0, |
| |
| QCA_WLAN_VENDOR_ATTR_RADAR_HISTORY_ENTRIES = 1, |
| QCA_WLAN_VENDOR_ATTR_RADAR_HISTORY_FREQ = 2, |
| QCA_WLAN_VENDOR_ATTR_RADAR_HISTORY_TIMESTAMP = 3, |
| QCA_WLAN_VENDOR_ATTR_RADAR_HISTORY_DETECTED = 4, |
| QCA_WLAN_VENDOR_ATTR_RADAR_HISTORY_PAD = 5, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_RADAR_HISTORY_LAST, |
| QCA_WLAN_VENDOR_ATTR_RADAR_HISTORY_MAX = |
| QCA_WLAN_VENDOR_ATTR_RADAR_HISTORY_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_mcc_quota_type: MCC channel time quota type |
| * |
| * @QCA_WLAN_VENDOR_MCC_QUOTA_TYPE_CLEAR: In the event, it indicates that the |
| * target exited MCC state and cleared the quota information. In the |
| * command it clears MCC quota setting and restores adaptive scheduling. |
| * @QCA_WLAN_VENDOR_MCC_QUOTA_TYPE_FIXED: Channel time quota is fixed and |
| * will not be changed. |
| * This quota type is present in command/event. |
| * @QCA_WLAN_VENDOR_MCC_QUOTA_TYPE_DYNAMIC: Channel time quota is dynamic |
| * and the target may change the quota based on the data activity. |
| * This quota type is only present in event. |
| * @QCA_WLAN_VENDOR_MCC_QUOTA_TYPE_LOW_LATENCY: Channel time quota is optimized |
| * by the target for low latency. |
| * This quota type is only present in command. |
| */ |
| enum qca_wlan_vendor_mcc_quota_type { |
| QCA_WLAN_VENDOR_MCC_QUOTA_TYPE_CLEAR = 0, |
| QCA_WLAN_VENDOR_MCC_QUOTA_TYPE_FIXED = 1, |
| QCA_WLAN_VENDOR_MCC_QUOTA_TYPE_DYNAMIC = 2, |
| QCA_WLAN_VENDOR_MCC_QUOTA_TYPE_LOW_LATENCY = 3, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_mcc_quota: Used by the vendor event |
| * QCA_NL80211_VENDOR_SUBCMD_MCC_QUOTA to indicate MCC channel |
| * quota information or as a command to set the required MCC quota for an |
| * interface. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_MCC_QUOTA_TYPE: u32 attribute. |
| * The type is defined in enum qca_wlan_vendor_mcc_quota_type. |
| * In a command this specifies the MCC quota type to be set for the interface. |
| * In an event this provides the current quota type in force. |
| * This is required in a command and an event. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_MCC_QUOTA_ENTRIES: Nested attribute to carry |
| * the list of channel quota entries. |
| * In an event each entry contains the frequency and respective time quota for |
| * all the MCC interfaces. |
| * In a command it specifies the interface index and respective time quota. |
| * In a command only one entry (ifindex, quota pair) may be specified. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_MCC_QUOTA_CHAN_FREQ: u32 attribute. |
| * Channel frequency in MHz. This is present only in an event. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_MCC_QUOTA_CHAN_TIME_PERCENTAGE: u32 attribute. |
| * Channel time quota expressed as percentage. |
| * This is present in an event and a command. |
| * In an command, the user shall specify the quota to be allocated for the |
| * interface represented by %QCA_WLAN_VENDOR_ATTR_MCC_QUOTA_IFINDEX. |
| * In an event this provides the existing quota for the channel. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_MCC_QUOTA_IFINDEX: u32 attribute. |
| * Specifies the interface index (netdev) for which the corresponding |
| * configurations are applied. This is required in a command only. Only one |
| * interface index may be specified. If not specified, the configuration is |
| * rejected. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_MCC_QUOTA_LOW_LATENCY_MODE_ENABLE |
| * 8-bit unsigned value to enable/disable Multi-Channel Concurrency |
| * low latency mode. The firmware will do optimization for low |
| * latency in Multi-Channel concurrency state if enabled. And all existing |
| * user quota setting will be overwritten by the target. |
| * 0 - disable(default), 1 - enable. |
| * It is only present in a command with quota type of |
| * QCA_WLAN_VENDOR_MCC_QUOTA_TYPE_LOW_LATENCY. |
| */ |
| enum qca_wlan_vendor_attr_mcc_quota { |
| QCA_WLAN_VENDOR_ATTR_MCC_QUOTA_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_MCC_QUOTA_TYPE = 1, |
| QCA_WLAN_VENDOR_ATTR_MCC_QUOTA_ENTRIES = 2, |
| QCA_WLAN_VENDOR_ATTR_MCC_QUOTA_CHAN_FREQ = 3, |
| QCA_WLAN_VENDOR_ATTR_MCC_QUOTA_CHAN_TIME_PERCENTAGE = 4, |
| QCA_WLAN_VENDOR_ATTR_MCC_QUOTA_IFINDEX = 5, |
| QCA_WLAN_VENDOR_ATTR_MCC_QUOTA_LOW_LATENCY_MODE_ENABLE = 6, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_MCC_QUOTA_LAST, |
| QCA_WLAN_VENDOR_ATTR_MCC_QUOTA_MAX = |
| QCA_WLAN_VENDOR_ATTR_MCC_QUOTA_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_roam_stats_invoke_reason - Roam invoke reason. These values |
| * are used by the attribute |
| * %QCA_WLAN_VENDOR_ATTR_ROAM_STATS_USER_TRIGGER_INVOKE_REASON. |
| * |
| * @QCA_WLAN_ROAM_STATS_INVOKE_REASON_UNDEFINED: Default value when target |
| * invoke roam. |
| * @QCA_WLAN_ROAM_STATS_INVOKE_REASON_NUD_FAILURE: Neighbor unreachable |
| * detection failed when the roam trigger. |
| * @QCA_WLAN_ROAM_STATS_INVOKE_REASON_USER_SPACE: Invoke from user space. |
| */ |
| |
| enum qca_wlan_roam_stats_invoke_reason { |
| QCA_WLAN_ROAM_STATS_INVOKE_REASON_UNDEFINED = 0, |
| QCA_WLAN_ROAM_STATS_INVOKE_REASON_NUD_FAILURE = 1, |
| QCA_WLAN_ROAM_STATS_INVOKE_REASON_USER_SPACE = 2, |
| }; |
| |
| /** |
| * enum qca_wlan_roam_stats_tx_failures_reason - Roam TX failures reason. These |
| * values are used by the attribute |
| * %QCA_WLAN_VENDOR_ATTR_ROAM_STATS_TX_FAILURES_REASON. |
| * |
| * @QCA_WLAN_ROAM_STATS_KICKOUT_REASON_UNSPECIFIED: Default value when |
| * roam by kickout. |
| * @QCA_WLAN_ROAM_STATS_KICKOUT_REASON_XRETRY: Excessive retry when roam |
| * trigger by kickout. |
| * @QCA_WLAN_ROAM_STATS_KICKOUT_REASON_INACTIVITY: Station inactivity when |
| * roam trigger by kickout. |
| * @QCA_WLAN_ROAM_STATS_KICKOUT_REASON_IBSS_DISCONNECT: IBSS disconnect when |
| * roam trigger by kickout. |
| * @QCA_WLAN_ROAM_STATS_KICKOUT_REASON_TDLS_DISCONNECT: TDLS peer has |
| * disappeared, and all TX is failing when roam trigger by kickout. |
| * @QCA_WLAN_ROAM_STATS_KICKOUT_REASON_SA_QUERY_TIMEOUT: SA query process |
| * timeout when roam trigger by kickout. |
| * @QCA_WLAN_ROAM_STATS_KICKOUT_REASON_ROAMING_EVENT: Directly connected |
| * peer has roamed to a repeater. |
| */ |
| enum qca_wlan_roam_stats_tx_failures_reason { |
| QCA_WLAN_ROAM_STATS_KICKOUT_REASON_UNSPECIFIED = 0, |
| QCA_WLAN_ROAM_STATS_KICKOUT_REASON_XRETRY = 1, |
| QCA_WLAN_ROAM_STATS_KICKOUT_REASON_INACTIVITY = 2, |
| QCA_WLAN_ROAM_STATS_KICKOUT_REASON_IBSS_DISCONNECT = 3, |
| QCA_WLAN_ROAM_STATS_KICKOUT_REASON_TDLS_DISCONNECT = 4, |
| QCA_WLAN_ROAM_STATS_KICKOUT_REASON_SA_QUERY_TIMEOUT = 5, |
| QCA_WLAN_ROAM_STATS_KICKOUT_REASON_ROAMING_EVENT = 6, |
| }; |
| |
| /** |
| * enum qca_wlan_roam_stats_abort_reason - Roam abort reason. These values |
| * are used by the attribute %QCA_WLAN_VENDOR_ATTR_ROAM_STATS_ABORT_REASON. |
| * |
| * @QCA_WLAN_ROAM_STATS_ABORT_UNSPECIFIED: Target did not specify the |
| * detailed reason for roam scan being aborted. |
| * @QCA_WLAN_ROAM_STATS_ABORT_LOWRSSI_DATA_RSSI_HIGH: Roam scan is not |
| * started due to high data RSSI during LOW-RSSI roaming. |
| * @QCA_WLAN_ROAM_STATS_ABORT_LOWRSSI_LINK_SPEED_GOOD: Roam scan is not |
| * started due to good link speed during LOW-RSSI roaming. |
| * @QCA_WLAN_ROAM_STATS_ABORT_BG_DATA_RSSI_HIGH: Roam scan is not started |
| * due to high data RSSI during background roaming. |
| * @QCA_WLAN_ROAM_STATS_ABORT_BG_RSSI_ABOVE_THRESHOLD: Roam scan is not |
| * started due to high beacon RSSI during background roaming |
| */ |
| enum qca_wlan_roam_stats_abort_reason { |
| QCA_WLAN_ROAM_STATS_ABORT_UNSPECIFIED = 0, |
| QCA_WLAN_ROAM_STATS_ABORT_LOWRSSI_DATA_RSSI_HIGH = 1, |
| QCA_WLAN_ROAM_STATS_ABORT_LOWRSSI_LINK_SPEED_GOOD = 2, |
| QCA_WLAN_ROAM_STATS_ABORT_BG_DATA_RSSI_HIGH = 3, |
| QCA_WLAN_ROAM_STATS_ABORT_BG_RSSI_ABOVE_THRESHOLD = 4, |
| }; |
| |
| /** |
| * enum qca_wlan_roam_stats_scan_type - Roam scan type define. |
| * These values are used by the attribute |
| * %QCA_WLAN_VENDOR_ATTR_ROAM_STATS_SCAN_TYPE. |
| * |
| * @QCA_WLAN_ROAM_STATS_SCAN_TYPE_PARTIAL: Partial channel scan |
| * @QCA_WLAN_ROAM_STATS_SCAN_TYPE_FULL: Full channel scan |
| * @QCA_WLAN_ROAM_STATS_SCAN_TYPE_NO_SCAN: No roam scan was triggered. |
| * This is generally used in BTM events to indicate BTM frame exchange logs. |
| * @QCA_WLAN_ROAM_STATS_SCAN_TYPE_HIGHER_BAND_5GHZ_6GHZ: Higher band roam scan |
| * from 2.4 GHz to 5 GHz or 6 GHz |
| * @QCA_WLAN_ROAM_STATS_SCAN_TYPE_HIGHER_BAND_6GHZ: Higher band roam scan from |
| * 5 GHz to 6 GHz |
| */ |
| enum qca_wlan_roam_stats_scan_type { |
| QCA_WLAN_ROAM_STATS_SCAN_TYPE_PARTIAL = 0, |
| QCA_WLAN_ROAM_STATS_SCAN_TYPE_FULL = 1, |
| QCA_WLAN_ROAM_STATS_SCAN_TYPE_NO_SCAN = 2, |
| QCA_WLAN_ROAM_STATS_SCAN_TYPE_HIGHER_BAND_5GHZ_6GHZ = 3, |
| QCA_WLAN_ROAM_STATS_SCAN_TYPE_HIGHER_BAND_6GHZ = 4, |
| }; |
| |
| /** |
| * enum qca_wlan_roam_stats_scan_dwell_type - Roam scan dwell type. |
| * These values are used by the attribute |
| * %QCA_WLAN_VENDOR_ATTR_ROAM_STATS_SCAN_DWELL_TYPE. |
| * |
| * @QCA_WLAN_ROAM_STATS_DWELL_TYPE_UNSPECIFIED: Target did not specify the |
| * detailed roam scan type. |
| * @QCA_WLAN_ROAM_STATS_DWELL_ACTIVE_TYPE: Active scan during roam. |
| * @QCA_WLAN_ROAM_STATS_DWELL_PASSIVE_TYPE: Passive scan during roam. |
| */ |
| enum qca_wlan_roam_stats_scan_dwell_type { |
| QCA_WLAN_ROAM_STATS_DWELL_TYPE_UNSPECIFIED = 0, |
| QCA_WLAN_ROAM_STATS_DWELL_TYPE_ACTIVE = 1, |
| QCA_WLAN_ROAM_STATS_DWELL_TYPE_PASSIVE = 2, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_roam_stats_scan_chan_info - Attributes used inside |
| * the %QCA_WLAN_VENDOR_ATTR_ROAM_STATS_SCAN_CHAN_INFO nested attribute. |
| */ |
| enum qca_wlan_vendor_attr_roam_stats_scan_chan_info { |
| /* 32-bit unsigned value to indicate center frequency of the primary |
| * channel in MHz for each roam scan channel. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_SCAN_CHANNEL_FREQ = 1, |
| /* 8-bit unsigned value to indicate channel scan type for each |
| * roam scan channel, values in qca_wlan_roam_stats_scan_dwell_type. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_SCAN_DWELL_TYPE = 2, |
| /* 32-bit unsigned value to indicate maximum scan time in milliseconds |
| * for each roam scan channel. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_MAX_DWELL_TIME = 3, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_SCAN_INFO_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_SCAN_INFO_FRAME_MAX = |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_SCAN_INFO_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_roam_stats_frame_subtype - Roam frame subtypes. These values |
| * are used by the attribute %QCA_WLAN_VENDOR_ATTR_ROAM_STATS_FRAME_SUBTYPE. |
| * |
| * @QCA_WLAN_ROAM_STATS_FRAME_SUBTYPE_PREAUTH: Pre-authentication frame |
| * @QCA_WLAN_ROAM_STATS_FRAME_SUBTYPE_REASSOC: Reassociation frame |
| * @QCA_WLAN_ROAM_STATS_FRAME_SUBTYPE_EAPOL_M1: EAPOL-Key M1 frame |
| * @QCA_WLAN_ROAM_STATS_FRAME_SUBTYPE_EAPOL_M2: EAPOL-Key M2 frame |
| * @QCA_WLAN_ROAM_STATS_FRAME_SUBTYPE_EAPOL_M3: EAPOL-Key M3 frame |
| * @QCA_WLAN_ROAM_STATS_FRAME_SUBTYPE_EAPOL_M4: EAPOL-Key M4 frame |
| * @QCA_WLAN_ROAM_STATS_FRAME_SUBTYPE_EAPOL_GTK_M1: EAPOL-Key GTK M1 frame |
| * @QCA_WLAN_ROAM_STATS_FRAME_SUBTYPE_EAPOL_GTK_M2: EAPOL-Key GTK M2 frame |
| */ |
| enum qca_wlan_roam_stats_frame_subtype { |
| QCA_WLAN_ROAM_STATS_FRAME_SUBTYPE_PREAUTH = 1, |
| QCA_WLAN_ROAM_STATS_FRAME_SUBTYPE_REASSOC = 2, |
| QCA_WLAN_ROAM_STATS_FRAME_SUBTYPE_EAPOL_M1 = 3, |
| QCA_WLAN_ROAM_STATS_FRAME_SUBTYPE_EAPOL_M2 = 4, |
| QCA_WLAN_ROAM_STATS_FRAME_SUBTYPE_EAPOL_M3 = 5, |
| QCA_WLAN_ROAM_STATS_FRAME_SUBTYPE_EAPOL_M4 = 6, |
| QCA_WLAN_ROAM_STATS_FRAME_SUBTYPE_EAPOL_GTK_M1 = 7, |
| QCA_WLAN_ROAM_STATS_FRAME_SUBTYPE_EAPOL_GTK_M2 = 8, |
| }; |
| |
| /** |
| * enum roam_frame_status - Specifies the valid values the vendor roam frame |
| * attribute QCA_WLAN_VENDOR_ATTR_ROAM_STATS_FRAME_STATUS can take. |
| * |
| * @QCA_WLAN_ROAM_FRAME_STATUS_SUCCESS: It indicates the roam frame was |
| * sent or received successfully. |
| * @QCA_WLAN_ROAM_FRAME_STATUS_FAIL: It indicates the roam frame sending or |
| * receiving failed. |
| */ |
| enum qca_wlan_roam_stats_frame_status { |
| QCA_WLAN_ROAM_STATS_FRAME_STATUS_SUCCESS = 0, |
| QCA_WLAN_ROAM_STATS_FRAME_STATUS_FAIL = 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_roam_stats_frame_info - Attributes used within the |
| * %QCA_WLAN_VENDOR_ATTR_ROAM_STATS_FRAME_INFO nested attribute. |
| */ |
| enum qca_wlan_vendor_attr_roam_stats_frame_info { |
| /* 8-bit unsigned value to indicate the frame subtype during |
| * roaming, one of the values in qca_wlan_roam_stats_frame_subtype. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_FRAME_SUBTYPE = 1, |
| /* 8-bit unsigned value to indicate the frame is successful or failed |
| * during roaming, one of the values in |
| * qca_wlan_roam_stats_frame_status. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_FRAME_STATUS = 2, |
| /* 64-bit unsigned value to indicate the timestamp for frame of |
| * preauthentication/reassociation/EAPOL-M1/EAPOL-M2/EAPOL-M3/EAPOL-M4 |
| * when sent or received during roaming, timestamp in milliseconds |
| * from system boot. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_FRAME_TIMESTAMP = 3, |
| /* Attribute used for padding for 64-bit alignment */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_FRAME_PAD = 4, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_FRAME_INFO_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_FRAME_INFO_MAX = |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_FRAME_INFO_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_roam_stats_info - Used by the attribute |
| * QCA_WLAN_VENDOR_ATTR_ROAM_STATS_INFO. |
| */ |
| enum qca_wlan_vendor_attr_roam_stats_info { |
| /* 64-bit unsigned value to indicate the timestamp when roam was |
| * triggered by the firmware, timestamp in milliseconds from system |
| * boot. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_ROAM_TRIGGER_TIMESTAMP = 1, |
| /* 32-bit unsigned value to indicate the roam trigger reason for the |
| * last roaming attempted by the firmware. This can be queried either |
| * in a connected state or disconnected state. The values of this |
| * attribute represent the roam trigger reason codes, which |
| * are defined in enum qca_roam_reason. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_TRIGGER_REASON = 2, |
| /* 8-bit unsigned value to indicate percentage of packets for which |
| * the RX rate is lower than the RX rate threshold in total RX packets, |
| * used for roaming trigger by per. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_PER_RXRATE_THRESHOLD_PERCENT = 3, |
| /* 8-bit unsigned value to indicate percentage of packets for which |
| * the TX rate is lower than TX rate threshold in total TX packets, |
| * used for roaming trigger by per. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_PER_TXRATE_THRESHOLD_PERCENT = 4, |
| /* 32-bit unsigned value to indicate final beacon miss count for |
| * trigger reason of beacon miss. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_FINAL_BMISS_CNT = 5, |
| /* 32-bit unsigned value to indicate consecutive beacon miss count |
| * for trigger reason of beacon miss. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_CONSECUTIVE_BMISS_CNT = 6, |
| /* 8-bit unsigned value to indicate QOS-NULL TX status for trigger |
| * reason of beacon miss, 0 - success, 1 - fail. |
| * If QOS-NULL TX status is successful, beacon miss final count and |
| * consecutive beacon miss count will be reset to zero, and roam will |
| * not be triggered. If QOS-NULL TX status is failed, beacon miss final |
| * count and consecutive beacon miss count continue to calculate until |
| * roaming trigger by beacon miss. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_BMISS_QOS_NULL_SUCCESS = 7, |
| /* 8-bit signed value to indicate connected AP RSSI in dBm |
| * for trigger reason of poor RSSI. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_POOR_RSSI_CURRENT_RSSI = 8, |
| /* 8-bit signed value to indicate RSSI threshold value in dBm |
| * for trigger reason of poor RSSI. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_POOR_RSSI_ROAM_RSSI_THRESHOLD = 9, |
| /* 8-bit unsigned value to indicate RX link speed status |
| * for trigger reason of poor RSSI, 0 - good link speed, |
| * 1 - bad link speed. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_POOR_RSSI_RX_LINKSPEED_STATUS = 10, |
| /* 8-bit signed value to indicate connected AP RSSI in dBm |
| * for trigger reason of better RSSI. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_BETTER_RSSI_CURRENT_RSSI = 11, |
| /* 8-bit signed value to indicate RSSI threshold value in dBm |
| * for trigger reason of better RSSI. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_BETTER_RSSI_HIGH_RSSI_THRESHOLD = 12, |
| /* 32-bit unsigned value to indicate RX throughput in bytes per second |
| * for trigger reason of congestion. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_CONGESTION_RX_TPUT = 13, |
| /* 32-bit unsigned value to indicate TX throughput in bytes per second |
| * for trigger reason of congestion. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_CONGESTION_TX_TPUT = 14, |
| /* 8-bit unsigned value to indicate roamable AP count |
| * for trigger reason of congestion. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_CONGESTION_ROAMABLE_CNT = 15, |
| /* 8-bit unsigned value to indicate invoke reason, one of the values |
| * defined in qca_wlan_roam_stats_invoke_reason. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_USER_TRIGGER_INVOKE_REASON = 16, |
| /* 8-bit unsigned value to indicate request mode for trigger reason |
| * of BTM, values are defined in IEEE Std 802.11-2020, 9.6.13.9. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_BTM_REQUEST_MODE = 17, |
| /* 32-bit unsigned value to indicate disassociate time in milliseconds |
| * for trigger reason of BTM. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_BTM_DISASSOC_IMMINENT_TIME = 18, |
| /* 32-bit unsigned value to indicate preferred candidate list valid |
| * interval in milliseconds for trigger reason of BTM. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_BTM_VALID_INTERNAL = 19, |
| /* 8-bit unsigned value to indicate the number of preferred |
| * candidates for trigger reason of BTM. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_BTM_CANDIDATE_LIST_CNT = 20, |
| /* 8-bit unsigned value to indicate response status for trigger |
| * reason of BTM, values are defined in IEEE Std 802.11-2020, |
| * Table 9-428 (BTM status code definitions). |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_BTM_RESPONSE_STATUS_CODE = 21, |
| /* 32-bit unsigned value to indicate BSS termination timeout value |
| * in milliseconds for trigger reason of BTM. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_BTM_BSS_TERMINATION_TIMEOUT = 22, |
| /* 32-bit unsigned value to indicate MBO associate retry timeout |
| * value in milliseconds for trigger reason of BTM. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_BTM_MBO_ASSOC_RETRY_TIMEOUT = 23, |
| /* 8-bit unsigned value to indicate dialog token number |
| * for trigger reason of BTM. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_BTM_REQ_DIALOG_TOKEN = 24, |
| /* 8-bit unsigned value to indicate percentage of connected AP |
| * channel congestion utilization for trigger reason of BSS load. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_BSS_CU_LOAD = 25, |
| /* 8-bit unsigned value to indicate disconnection type |
| * for trigger reason of disconnection. 1 - Deauthentication, |
| * 2 - Disassociation. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_DISCONNECTION_TYPE = 26, |
| /* 16-bit unsigned value to indicate deauthentication or disassociation |
| * reason for trigger reason of disconnection, values are defined |
| * in IEEE Std 802.11-2020, Table 9-49 (Reason codes). |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_DISCONNECTION_REASON = 27, |
| /* 32-bit unsigned value to indicate milliseconds of roam scan |
| * periodicity when needing to roam to find a better AP for trigger |
| * reason of periodic timer. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_PERIODIC_TIMER_MS = 28, |
| /* 8-bit signed value to indicate connected AP RSSI in dBm for |
| * trigger reason of background scan. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_BACKGROUND_SCAN_CURRENT_RSSI = 29, |
| /* 8-bit signed value to indicate data RSSI in dBm for trigger reason |
| * of background scan. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_BACKGROUND_SCAN_DATA_RSSI = 30, |
| /* 8-bit signed value to indicate data RSSI threshold in dBm |
| * for trigger reason of background scan. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_BACKGROUND_SCAN_DATA_RSSI_THRESH = 31, |
| /* 32-bit unsigned value to indicate consecutive TX failure threshold |
| * for trigger reason of TX failures. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_TX_FAILURES_THRESHOLD = 32, |
| /* 8-bit unsigned value to indicate TX failure reason for trigger |
| * reason of TX failures, one of the values defined in |
| * qca_wlan_roam_stats_tx_failures_reason. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_TX_FAILURES_REASON = 33, |
| /* 8-bit unsigned value to indicate detail abort reason. One of the |
| * values in enum qca_wlan_roam_stats_abort_reason. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_ABORT_REASON = 34, |
| /* 8-bit signed value to indicate data RSSI in dBm when aborting the |
| * roam scan. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_DATA_RSSI = 35, |
| /* 8-bit signed value to indicate data RSSI threshold in dBm when |
| * aborting the roam scan. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_DATA_RSSI_THRESHOLD = 36, |
| /* 8-bit unsigned value to indicate data RSSI threshold in RX link |
| * speed status when aborting the roam scan. |
| * 0 - good link speed, 1 - bad link speed |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_DATA_RX_LINKSPEED_STATUS = 37, |
| /* 8-bit unsigned value to indicate roaming scan type. |
| * One of the values in enum qca_wlan_roam_stats_scan_type. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_SCAN_TYPE = 38, |
| /* 8-bit unsigned value to indicate roaming result, used in STA mode |
| * only. |
| * 0-Roaming is successful, 1-Roaming is failed |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_ROAM_STATUS = 39, |
| /* 8-bit unsigned value to indicate the roam fail reason for the |
| * last failed roaming attempt by the firmware. Different roam failure |
| * reason codes are specified in enum qca_vendor_roam_fail_reasons. |
| * This can be queried either in connected state or disconnected state. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_FAIL_REASON = 40, |
| /* Nested attribute. Indicate roam scan info for each channel, the |
| * attributes defined in enum |
| * qca_wlan_vendor_attr_roam_stats_scan_chan_info are used inside |
| * this attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_SCAN_CHAN_INFO = 41, |
| /* 32-bit unsigned value to indicate total scan time during roam scan |
| * all channels, time in milliseconds. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_TOTAL_SCAN_TIME = 42, |
| /* Nested attribute. This attribute shall be used by the driver to |
| * send roam information of each subtype. The attributes defined in |
| * enum qca_wlan_vendor_attr_roam_stats_frame_info are used inside |
| * this attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_FRAME_INFO = 43, |
| /* Attribute used for padding for 64-bit alignment */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_PAD = 44, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_MAX = |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_roam_cached_stats - Vendor subcmd attributes to |
| * report cached roam info from the driver to user space, enum values are used |
| * for netlink attributes sent with the |
| * %QCA_NL80211_VENDOR_SUBCMD_ROAM_STATS sub command. |
| */ |
| enum qca_wlan_vendor_attr_roam_cached_stats { |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_INVALID = 0, |
| /* Nested attribute, this attribute contains nested array roam info |
| * statistics defined in enum qca_wlan_vendor_attr_roam_stats_info. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_STATS_INFO = 1, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_CACHED_STATS_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_ROAM_CACHED_STATS_MAX = |
| QCA_WLAN_VENDOR_ATTR_ROAM_CACHED_STATS_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_supported_radio_cfg - Attributes for |
| * radio configurations present in each radio combination. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SUPPORTED_RADIO_CFG_BAND: u32 attribute indicates |
| * the band info in the radio configuration. Uses the enum qca_set_band values. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SUPPORTED_RADIO_CFG_ANTENNA: u8 attribute indicates |
| * the number of antennas info in the radio configuration. |
| */ |
| enum qca_wlan_vendor_attr_supported_radio_cfg { |
| QCA_WLAN_VENDOR_ATTR_SUPPORTED_RADIO_CFG_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_SUPPORTED_RADIO_CFG_BAND = 1, |
| QCA_WLAN_VENDOR_ATTR_SUPPORTED_RADIO_CFG_ANTENNA = 2, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_SUPPORTED_RADIO_CFG_LAST, |
| QCA_WLAN_VENDOR_ATTR_SUPPORTED_RADIO_CFG_MAX = |
| QCA_WLAN_VENDOR_ATTR_SUPPORTED_RADIO_CFG_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_radio_combination - Attributes for |
| * radio combinations supported by the device. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_RADIO_COMBINATIONS_CFGS: Nested attribute |
| * provides the radio configurations present in the radio combination. |
| * Uses the enum qca_wlan_vendor_attr_supported_radio_cfg attributes. |
| * This attribute provides the values for radio combination matrix. |
| * For standalone config, the number of config values is one and the config |
| * carries the band and antenna information for standalone configuration. For |
| * Dual Band Simultaneous (DBS)/Single Band Simultaneous (SBS) mode |
| * configuration the number of config values is two and the config carries the |
| * band and antenna information for each simultaneous radio. |
| */ |
| enum qca_wlan_vendor_attr_radio_combination { |
| QCA_WLAN_VENDOR_ATTR_RADIO_COMBINATIONS_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_RADIO_COMBINATIONS_CFGS = 1, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_RADIO_COMBINATIONS_LAST, |
| QCA_WLAN_VENDOR_ATTR_RADIO_COMBINATIONS_MAX = |
| QCA_WLAN_VENDOR_ATTR_RADIO_COMBINATIONS_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_radio_combination_matrix - Attributes used by |
| * %QCA_NL80211_VENDOR_SUBCMD_GET_RADIO_COMBINATION_MATRIX |
| * |
| * @QCA_WLAN_VENDOR_ATTR_RADIO_MATRIX_SUPPORTED_CFGS: Nested attribute |
| * provides the radio combinations supported by the device. |
| * Uses the enum qca_wlan_vendor_attr_radio_combination attributes. |
| * For example, in the radio combination matrix for a device which has two |
| * radios, where one radio is capable of 2.4 GHz 2X2 only and another radio is |
| * capable of either 5 GHz or 6 GHz 2X2, the possible number of radio |
| * combinations is 5 and the radio combinations are |
| * {{{2.4 GHz 2X2}}, //Standalone 2.4 GHz |
| * {{5 GHz 2X2}}, //Standalone 5 GHz |
| * {{6 GHz 2X2}}, //Standalone 6 GHz |
| * {{2.4 GHz 2X2}, {5 GHz 2X2}}, //2.4 GHz + 5 GHz DBS |
| * {{2.4 GHz 2X2}, {6 GHz 2X2}}} //2.4 GHz + 6 GHz DBS |
| * The band and antenna info together as nested data provides one radio config. |
| * Standalone configuration has one config with band and antenna nested data. |
| * Dual Band Simultaneous (DBS)/Single Band Simultaneous (SBS) configuration |
| * have two nested band and antenna info data. |
| */ |
| enum qca_wlan_vendor_attr_radio_combination_matrix { |
| QCA_WLAN_VENDOR_ATTR_RADIO_MATRIX_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_RADIO_MATRIX_SUPPORTED_CFGS = 1, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_RADIO_MATRIX_LAST, |
| QCA_WLAN_VENDOR_ATTR_RADIO_MATRIX_MAX = |
| QCA_WLAN_VENDOR_ATTR_RADIO_MATRIX_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_mdns_offload - Attributes used by |
| * %QCA_NL80211_VENDOR_SUBCMD_MDNS_OFFLOAD vendor command. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_ENABLE: Required (flag) |
| * Enable mDNS offload. This attribute is mandatory to enable |
| * mDNS offload feature. If this attribute is not present, mDNS offload |
| * is disabled. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_TABLE: Nested attribute containing |
| * one or more %QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_ENTRY attributes. This |
| * attribute is mandatory when enabling the feature, and not required when |
| * disabling the feature. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_ENTRY: Nested attribute containing |
| * the following attributes: |
| * %QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_FQDN |
| * %QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_ANSWER_RESOURCE_RECORDS_COUNT |
| * %QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_ANSWER_PAYLOAD |
| * |
| * @QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_FQDN: Required string attribute. |
| * It consists of a hostname and ".local" as the domain name. The character |
| * set is limited to UTF-8 encoding. The maximum allowed size is 63 bytes. |
| * It is used to compare the domain in the "QU" query. Only 1 FQDN is |
| * supported per vdev. |
| * For example: myphone.local |
| * |
| * @QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_ANSWER_RESOURCE_RECORDS_COUNT: Required |
| * u16 attribute. It specifies the total number of resource records present |
| * in the answer section of the answer payload. This attribute is needed by the |
| * firmware to populate the mDNS response frame for mDNS queries without having |
| * to parse the answer payload. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_ANSWER_PAYLOAD: Required binary blob |
| * attribute sent by the mdnsResponder from userspace. It contains resource |
| * records of various types (e.g., A, AAAA, PTR, TXT) and service list. This |
| * payload is passed down to the firmware and is transmitted in response to |
| * mDNS queries. |
| * The maximum supported size of the answer payload is 512 bytes. |
| */ |
| enum qca_wlan_vendor_attr_mdns_offload { |
| QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_ENABLE = 1, |
| QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_TABLE = 2, |
| QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_ENTRY = 3, |
| QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_FQDN = 4, |
| QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_ANSWER_RESOURCE_RECORDS_COUNT = 5, |
| QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_ANSWER_PAYLOAD = 6, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_MAX = |
| QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * qca_wlan_vendor_monitor_data_frame_type - Represent the various |
| * Data frame types to be sent over the monitor interface. |
| */ |
| enum qca_wlan_vendor_monitor_data_frame_type { |
| QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_ALL = BIT(0), |
| /* valid only if QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_ALL is not set |
| */ |
| QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_ARP = BIT(1), |
| QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_DHCPV4 = BIT(2), |
| QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_DHCPV6 = BIT(3), |
| QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_EAPOL = BIT(4), |
| QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_DNSV4 = BIT(5), |
| QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_DNSV6 = BIT(6), |
| QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_TCP_SYN = BIT(7), |
| QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_TCP_SYNACK = BIT(8), |
| QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_TCP_FIN = BIT(9), |
| QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_TCP_FINACK = BIT(10), |
| QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_TCP_ACK = BIT(11), |
| QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_TCP_RST = BIT(12), |
| QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_ICMPV4 = BIT(13), |
| QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_ICMPV6 = BIT(14), |
| QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_RTP = BIT(15), |
| QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_SIP = BIT(16), |
| QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_QOS_NULL = BIT(17), |
| }; |
| |
| /** |
| * qca_wlan_vendor_monitor_mgmt_frame_type - Represent the various |
| * Management frame types to be sent over the monitor interface. |
| * @QCA_WLAN_VENDOR_MONITOR_MGMT_FRAME_TYPE_ALL: All the Management Frames. |
| * @QCA_WLAN_VENDOR_MONITOR_MGMT_CONNECT_NO_BEACON: All the Management frames |
| * except the Beacon frame. |
| * @QCA_WLAN_VENDOR_MONITOR_MGMT_CONNECT_BEACON: Only the connected |
| * BSSID Beacon frames. Valid only in the connected state. |
| * @QCA_WLAN_VENDOR_MONITOR_MGMT_CONNECT_SCAN_BEACON: Represents |
| * the Beacon frames obtained during the scan (off channel and connected |
| * channel), when in connected state. |
| */ |
| enum qca_wlan_vendor_monitor_mgmt_frame_type { |
| QCA_WLAN_VENDOR_MONITOR_MGMT_FRAME_TYPE_ALL = BIT(0), |
| /* valid only if QCA_WLAN_VENDOR_MONITOR_MGMT_FRAME_TYPE_ALL is not set |
| */ |
| QCA_WLAN_VENDOR_MONITOR_MGMT_NO_BEACON = BIT(1), |
| QCA_WLAN_VENDOR_MONITOR_MGMT_CONNECT_BEACON = BIT(2), |
| QCA_WLAN_VENDOR_MONITOR_MGMT_CONNECT_SCAN_BEACON = BIT(3), |
| }; |
| |
| /** |
| * qca_wlan_vendor_monitor_ctrl_frame_type - Represent the various |
| * Control frame types to be sent over the monitor interface. |
| * @QCA_WLAN_VENDOR_MONITOR_CTRL_FRAME_TYPE_ALL: All the Control frames |
| * @QCA_WLAN_VENDOR_MONITOR_CTRL_TRIGGER_FRAME: Trigger frame |
| */ |
| enum qca_wlan_vendor_monitor_ctrl_frame_type { |
| QCA_WLAN_VENDOR_MONITOR_CTRL_FRAME_TYPE_ALL = BIT(0), |
| /* valid only if QCA_WLAN_VENDOR_MONITOR_CTRL_FRAME_TYPE_ALL is not set |
| */ |
| QCA_WLAN_VENDOR_MONITOR_CTRL_TRIGGER_FRAME = BIT(1), |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_set_monitor_mode - Used by the |
| * vendor command QCA_NL80211_VENDOR_SUBCMD_SET_MONITOR_MODE to set the |
| * monitor mode. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_DATA_TX_FRAME_TYPE: u32 attribute. |
| * Represents the TX Data frame types to be monitored (u32). These Data frames |
| * are represented by enum qca_wlan_vendor_monitor_data_frame_type. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_DATA_RX_FRAME_TYPE: u32 attribute. |
| * Represents the RX Data frame types to be monitored (u32). These Data frames |
| * are represented by enum qca_wlan_vendor_monitor_data_frame_type. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_MGMT_TX_FRAME_TYPE: u32 attribute. |
| * Represents the TX Management frame types to be monitored (u32). These |
| * Management frames are represented by |
| * enum qca_wlan_vendor_monitor_mgmt_frame_type. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_MGMT_RX_FRAME_TYPE: u32 attribute. |
| * Represents the RX Management frame types to be monitored (u32). These |
| * Management frames are represented by |
| * enum qca_wlan_vendor_monitor_mgmt_frame_type. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_CTRL_TX_FRAME_TYPE: u32 attribute. |
| * Represents the TX Control frame types to be monitored (u32). These Control |
| * frames are represented by enum qca_wlan_vendor_monitor_ctrl_frame_type. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_CTRL_RX_FRAME_TYPE: u32 attribute. |
| * Represents the RX Control frame types to be monitored (u32). These Control |
| * frames are represented by enum qca_wlan_vendor_monitor_ctrl_frame_type. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_CONNECTED_BEACON_INTERVAL: u32 |
| * attribute. |
| * Represents the interval in milliseconds only for the connected Beacon frames, |
| * expecting the connected BSS's Beacon frames to be sent on the monitor |
| * interface at this specific interval. |
| */ |
| enum qca_wlan_vendor_attr_set_monitor_mode { |
| QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_DATA_TX_FRAME_TYPE = 1, |
| QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_DATA_RX_FRAME_TYPE = 2, |
| QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_MGMT_TX_FRAME_TYPE = 3, |
| QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_MGMT_RX_FRAME_TYPE = 4, |
| QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_CTRL_TX_FRAME_TYPE = 5, |
| QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_CTRL_RX_FRAME_TYPE = 6, |
| QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_CONNECTED_BEACON_INTERVAL = 7, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_MAX = |
| QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_roam_scan_state - Roam scan state flags. |
| * Bits will be set to 1 if the corresponding state is enabled. |
| * |
| * @QCA_VENDOR_WLAN_ROAM_SCAN_STATE_START: Scan Start. |
| * @QCA_VENDOR_WLAN_ROAM_SCAN_STATE_END: Scan end. |
| */ |
| enum qca_wlan_vendor_roam_scan_state { |
| QCA_WLAN_VENDOR_ROAM_SCAN_STATE_START = BIT(0), |
| QCA_WLAN_VENDOR_ROAM_SCAN_STATE_END = BIT(1), |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_roam_event_type - Roam event type flags. |
| * Bits will be set to 1 if the corresponding event is notified. |
| * |
| * @QCA_WLAN_VENDOR_ROAM_EVENT_TRIGGER_REASON: Represents that the roam event |
| * carries the trigger reason. When set, it is expected that the roam event |
| * carries the respective reason via the attribute |
| * QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_TRIGGER_REASON. This event also carries |
| * the BSSID, RSSI, frequency info of the AP to which the roam is attempted. |
| * |
| * @QCA_WLAN_VENDOR_ROAM_EVENT_FAIL_REASON: Represents that the roam event |
| * carries the roam fail reason. When set, it is expected that the roam event |
| * carries the respective reason via the attribute |
| * QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_FAIL_REASON. This event also carries the |
| * BSSID, RSSI, frequency info of the AP to which the roam was attempted. |
| * |
| * @QCA_WLAN_VENDOR_ROAM_EVENT_INVOKE_FAIL_REASON: Represents that the roam |
| * event carries the roam invoke fail reason. When set, it is expected that |
| * the roam event carries the respective reason via the attribute |
| * QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_INVOKE_FAIL_REASON. |
| * |
| * @QCA_WLAN_VENDOR_ROAM_EVENT_SCAN_STATE: Represents that the roam event |
| * carries the roam scan state. When set, it is expected that the roam event |
| * carries the respective scan state via the attribute |
| * QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_ROAM_SCAN_STATE and the corresponding |
| * frequency info via QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_ROAM_SCAN_FREQ_LIST. |
| */ |
| enum qca_wlan_vendor_roam_event_type { |
| QCA_WLAN_VENDOR_ROAM_EVENT_TRIGGER_REASON = BIT(0), |
| QCA_WLAN_VENDOR_ROAM_EVENT_FAIL_REASON = BIT(1), |
| QCA_WLAN_VENDOR_ROAM_EVENT_INVOKE_FAIL_REASON = BIT(2), |
| QCA_WLAN_VENDOR_ROAM_EVENT_ROAM_SCAN_STATE = BIT(3), |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_roam_events_candidate_info: Roam candidate info. |
| * Referred by QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_CANDIDATE_INFO. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_CANDIDATE_INFO_BSSID: 6-byte MAC address |
| * representing the BSSID of the AP to which the roam is attempted. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_CANDIDATE_INFO_RSSI: Signed 32-bit value |
| * in dBm, signifying the RSSI of the candidate BSSID to which the Roaming is |
| * attempted. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_CANDIDATE_INFO_FREQ: u32, frequency in MHz |
| * on which the roam is attempted. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_CANDIDATE_INFO_FAIL_REASON: u32, used in |
| * STA mode only. This represents the roam fail reason for the last failed |
| * roaming attempt by the firmware for the specific BSSID. Different roam |
| * failure reason codes are specified in enum qca_vendor_roam_fail_reasons. |
| */ |
| enum qca_wlan_vendor_attr_roam_events_candidate_info { |
| QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_CANDIDATE_INFO_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_CANDIDATE_INFO_BSSID = 1, |
| QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_CANDIDATE_INFO_RSSI = 2, |
| QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_CANDIDATE_INFO_FREQ = 3, |
| QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_CANDIDATE_INFO_FAIL_REASON = 4, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_CANDIDATE_INFO_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_CANDIDATE_INFO_MAX = |
| QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_CANDIDATE_INFO_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_roam_events - Used by the |
| * vendor command QCA_NL80211_VENDOR_SUBCMD_ROAM_EVENTS to either configure the |
| * roam events to the driver or notify these events from the driver. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_CONFIGURE: u8 attribute. Configures the |
| * driver/firmware to enable/disable the notification of roam events. It's a |
| * mandatory attribute and used only in the request from the userspace to the |
| * host driver. 1-Enable, 0-Disable. |
| * If the roaming is totally offloaded to the firmware, this request when |
| * enabled shall mandate the firmware to notify all the relevant roam events |
| * represented by the below attributes. If the host is in the suspend mode, |
| * the behavior of the firmware to notify these events is guided by |
| * QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_DEVICE_STATE, and if the request is to get |
| * these events in the suspend state, the firmware is expected to wake up the |
| * host before the respective events are notified. Please note that such a |
| * request to get the events in the suspend state will have a definite power |
| * implication. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_SUSPEND_STATE: flag attribute. Represents |
| * that the roam events need to be notified in the suspend state too. By |
| * default, these roam events are notified in the resume state. With this flag, |
| * the roam events are notified in both resume and suspend states. |
| * This attribute is used in the request from the userspace to the host driver. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_TYPE: u32, used in STA mode only. |
| * Represents the different roam event types, signified by the enum |
| * qca_wlan_vendor_roam_event_type. |
| * Each bit of this attribute represents the different roam even types reported |
| * through QCA_NL80211_VENDOR_SUBCMD_ROAM_EVENTS. |
| * This is sent as an event through QCA_NL80211_VENDOR_SUBCMD_ROAM_EVENTS. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_TRIGGER_REASON: u32, used in STA |
| * mode only. This represents the roam trigger reason for the last roaming |
| * attempted by the firmware. Each bit of this attribute represents the |
| * different roam trigger reason code which are defined in enum |
| * qca_vendor_roam_triggers. |
| * This is sent as an event through QCA_NL80211_VENDOR_SUBCMD_ROAM_EVENTS. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_INVOKE_FAIL_REASON: u32, used in |
| * STA mode only. This represents the roam invoke fail reason for the last |
| * failed roam invoke. Different roam invoke failure reason codes |
| * are specified in enum qca_vendor_roam_invoke_fail_reasons. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_CANDIDATE_INFO: Array of candidates info |
| * for which the roam is attempted. Each entry is a nested attribute defined |
| * by enum qca_wlan_vendor_attr_roam_events_candidate_info. |
| * This is sent as an event through QCA_NL80211_VENDOR_SUBCMD_ROAM_EVENTS. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_ROAM_SCAN_STATE: u8 attribute. Represents |
| * the scan state on which the roam events need to be notified. The values for |
| * this attribute are referred from enum qca_wlan_vendor_roam_scan_state. |
| * This is sent as an event through QCA_NL80211_VENDOR_SUBCMD_ROAM_EVENTS. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_ROAM_SCAN_FREQ_LIST: Nested attribute of |
| * u32 values. List of frequencies in MHz considered for a roam scan. |
| * This is sent as an event through QCA_NL80211_VENDOR_SUBCMD_ROAM_EVENTS. |
| */ |
| enum qca_wlan_vendor_attr_roam_events { |
| QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_CONFIGURE = 1, |
| QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_SUSPEND_STATE = 2, |
| QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_TYPE = 3, |
| QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_TRIGGER_REASON = 4, |
| QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_INVOKE_FAIL_REASON = 5, |
| QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_CANDIDATE_INFO = 6, |
| QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_ROAM_SCAN_STATE = 7, |
| QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_ROAM_SCAN_FREQ_LIST = 8, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_MAX = |
| QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_AFTER_LAST -1, |
| }; |
| |
| /** |
| * enum qca_wlan_ratemask_params_type - Rate mask config type |
| * |
| * @QCA_WLAN_RATEMASK_PARAMS_TYPE_CCK_OFDM: CCK/OFDM rate mask config |
| * @QCA_WLAN_RATEMASK_PARAMS_TYPE_HT: HT rate mask config |
| * @QCA_WLAN_RATEMASK_PARAMS_TYPE_VHT: VHT rate mask config |
| * @QCA_WLAN_RATEMASK_PARAMS_TYPE_HE: HE rate mask config |
| */ |
| enum qca_wlan_ratemask_params_type { |
| QCA_WLAN_RATEMASK_PARAMS_TYPE_CCK_OFDM = 0, |
| QCA_WLAN_RATEMASK_PARAMS_TYPE_HT = 1, |
| QCA_WLAN_RATEMASK_PARAMS_TYPE_VHT = 2, |
| QCA_WLAN_RATEMASK_PARAMS_TYPE_HE = 3, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_ratemask_params - Used by the |
| * vendor command QCA_NL80211_VENDOR_SUBCMD_RATEMASK_CONFIG. |
| * This is used to set the rate mask value to be used in rate selection. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_RATEMASK_PARAMS_LIST: |
| * Array of nested containing attributes |
| * QCA_WLAN_VENDOR_ATTR_RATEMASK_PARAMS_TYPE and |
| * QCA_WLAN_VENDOR_ATTR_RATEMASK_PARAMS_BITMAP. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_RATEMASK_PARAMS_TYPE: u8, represents |
| * the different PHY types to which the rate mask config is to be applied. |
| * The values for this attribute are referred from enum |
| * qca_wlan_vendor_ratemask_params_type. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_RATEMASK_PARAMS_BITMAP: binary, rate mask bitmap. |
| * A bit value of 1 represents rate is enabled and a value of 0 |
| * represents rate is disabled. |
| * For HE targets, 12 bits correspond to one NSS setting. |
| * b0-13 => NSS1, MCS 0-13 |
| * b14-27 => NSS2, MCS 0-13 and so on for other NSS. |
| * For VHT targets, 10 bits correspond to one NSS setting. |
| * b0-9 => NSS1, MCS 0-9 |
| * b10-19 => NSS2, MCS 0-9 and so on for other NSS. |
| * For HT targets, 8 bits correspond to one NSS setting. |
| * b0-7 => NSS1, MCS 0-7 |
| * b8-15 => NSS2, MCS 0-7 and so on for other NSS. |
| * For OFDM/CCK targets, 8 bits correspond to one NSS setting. |
| */ |
| enum qca_wlan_vendor_attr_ratemask_params { |
| QCA_WLAN_VENDOR_ATTR_RATEMASK_PARAMS_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_RATEMASK_PARAMS_LIST = 1, |
| QCA_WLAN_VENDOR_ATTR_RATEMASK_PARAMS_TYPE = 2, |
| QCA_WLAN_VENDOR_ATTR_RATEMASK_PARAMS_BITMAP = 3, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_RATEMASK_PARAMS_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_RATEMASK_PARAMS_MAX = |
| QCA_WLAN_VENDOR_ATTR_RATEMASK_PARAMS_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_audio_data_path - Defines the data path to be used for audio |
| * traffic. |
| * |
| * @QCA_WLAN_AUDIO_DATA_PATH_VIA_HOST_PROCESSOR: |
| * Send audio traffic through the host processor. |
| * @QCA_WLAN_AUDIO_DATA_PATH_VIA_LOW_POWER_DSP: |
| * Send audio traffic using the low power DSP to/from the encoder. |
| */ |
| enum qca_wlan_audio_data_path { |
| QCA_WLAN_AUDIO_DATA_PATH_VIA_HOST_PROCESSOR = 0, |
| QCA_WLAN_AUDIO_DATA_PATH_VIA_LOW_POWER_DSP = 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_pasn_action - Action to authenticate (and generate keys |
| * for) or drop existing PASN security association for the listed the |
| * peers. Used by QCA_WLAN_VENDOR_ATTR_PASN_ACTION and sent from the driver |
| * to userspace. |
| * |
| * @QCA_WLAN_VENDOR_PASN_ACTION_AUTH: Initiate PASN handshake with the peer |
| * devices indicated with %QCA_WLAN_VENDOR_ATTR_PASN_PEER_MAC_ADDR. |
| * @QCA_WLAN_VENDOR_PASN_ACTION_DELETE_SECURE_RANGING_CONTEXT: Indication from |
| * the driver to userspace to inform that the existing PASN keys of the |
| * peer devices specified with %QCA_WLAN_VENDOR_ATTR_PASN_PEER_MAC_ADDR are |
| * not valid anymore. |
| */ |
| enum qca_wlan_vendor_pasn_action { |
| QCA_WLAN_VENDOR_PASN_ACTION_AUTH, |
| QCA_WLAN_VENDOR_PASN_ACTION_DELETE_SECURE_RANGING_CONTEXT, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_pasn_peer: Defines the nested attributes used in |
| * QCA_WLAN_VENDOR_ATTR_PASN_PEERS. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_PASN_PEER_SRC_ADDR: This attribute is optional in the |
| * event from the driver to userspace and represents the local MAC address |
| * to be used for PASN handshake. When this attribute is present, userspace |
| * shall use the source address specified in this attribute by the driver |
| * for PASN handshake with peer device. |
| * This attribute is required in a command response from userspace to the |
| * driver and represents the MAC address that was used in PASN handshake |
| * with the peer device. |
| * @QCA_WLAN_VENDOR_ATTR_PASN_PEER_MAC_ADDR: Indicates the MAC address of the |
| * peer device to which PASN handshake is requested in an event from the |
| * driver to userspace when QCA_WLAN_VENDOR_ATTR_PASN_ACTION is set to |
| * QCA_WLAN_VENDOR_PASN_ACTION_AUTH. |
| * Indicates the MAC address of the peer device for which the keys are to |
| * be invalidated in an event from the driver to userspace when |
| * QCA_WLAN_VENDOR_ATTR_PASN_ACTION is set to |
| * QCA_WLAN_VENDOR_PASN_ACTION_DELETE_SECURE_RANGING_CONTEXT. |
| * Indicates the MAC address of the peer device for which the status is |
| * being sent in a status report from userspace to the driver. |
| * @QCA_WLAN_VENDOR_ATTR_PASN_PEER_LTF_KEYSEED_REQUIRED: NLA_FLAG attribute used |
| * in the event from the driver to userspace. When set, userspace is |
| * required to derive LTF key seed from KDK and set it to the driver. |
| * @QCA_WLAN_VENDOR_ATTR_PASN_PEER_STATUS_SUCCESS: NLA_FLAG attribute. This |
| * attribute is used in the command response from userspace to the driver. |
| * If present, it indicates the successful PASN handshake with the peer. If |
| * this flag is not present, it indicates that the PASN handshake with the |
| * peer device failed. |
| */ |
| enum qca_wlan_vendor_attr_pasn_peer { |
| QCA_WLAN_VENDOR_ATTR_PASN_PEER_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_PASN_PEER_SRC_ADDR = 1, |
| QCA_WLAN_VENDOR_ATTR_PASN_PEER_MAC_ADDR = 2, |
| QCA_WLAN_VENDOR_ATTR_PASN_PEER_LTF_KEYSEED_REQUIRED = 3, |
| QCA_WLAN_VENDOR_ATTR_PASN_PEER_STATUS_SUCCESS = 4, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_PASN_PEER_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_PASN_PEER_MAX = |
| QCA_WLAN_VENDOR_ATTR_PASN_PEER_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_pasn: Defines the attributes used in the |
| * QCA_NL80211_VENDOR_SUBCMD_PASN command. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_PASN_ACTION: u32 attribute, possible values are |
| * defined in enum qca_wlan_vendor_pasn_action and used only in an event |
| * from the driver to userspace. |
| * @QCA_WLAN_VENDOR_ATTR_PASN_PEERS: Nested attribute, used to pass PASN peer |
| * details for each peer and used in both an event and a command response. |
| * The nested attributes used inside QCA_WLAN_VENDOR_ATTR_PASN_PEERS are |
| * defined in enum qca_wlan_vendor_attr_pasn_peer. |
| */ |
| enum qca_wlan_vendor_attr_pasn { |
| QCA_WLAN_VENDOR_ATTR_PASN_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_PASN_ACTION = 1, |
| QCA_WLAN_VENDOR_ATTR_PASN_PEERS = 2, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_PASN_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_PASN_MAX = |
| QCA_WLAN_VENDOR_ATTR_PASN_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_secure_ranging_ctx_action - Used to add or delete |
| * the ranging security context derived from PASN for each peer. Used in |
| * QCA_WLAN_VENDOR_ATTR_SECURE_RANGING_CTX_ACTION. |
| * |
| * @QCA_WLAN_VENDOR_SECURE_RANGING_CTX_ACTION_ADD: Add the secure ranging |
| * context for the peer. |
| * @QCA_WLAN_VENDOR_SECURE_RANGING_CTX_ACTION_DELETE: Delete the secure ranging |
| * context for the peer. |
| */ |
| enum qca_wlan_vendor_secure_ranging_ctx_action { |
| QCA_WLAN_VENDOR_SECURE_RANGING_CTX_ACTION_ADD, |
| QCA_WLAN_VENDOR_SECURE_RANGING_CTX_ACTION_DELETE, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_sha_type - SHA types. Used to configure the SHA type |
| * used for deriving PASN keys to the driver. Used in |
| * QCA_WLAN_VENDOR_ATTR_SECURE_RANGING_CTX_SHA_TYPE |
| * @QCA_WLAN_VENDOR_SHA_256: SHA-256 |
| * @QCA_WLAN_VENDOR_SHA_384: SHA-384 |
| */ |
| enum qca_wlan_vendor_sha_type { |
| QCA_WLAN_VENDOR_SHA_256, |
| QCA_WLAN_VENDOR_SHA_384, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_secure_ranging_ctx: Defines the attributes used |
| * to set security context for the PASN peer from userspace to the driver. |
| * Used with QCA_NL80211_VENDOR_SUBCMD_SECURE_RANGING_CONTEXT. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SECURE_RANGING_CTX_ACTION: u32 attribute, possible |
| * values are defined in enum qca_wlan_vendor_secure_ranging_ctx_action |
| * @QCA_WLAN_VENDOR_ATTR_SECURE_RANGING_CTX_SRC_ADDR: The local MAC address that |
| * was used during the PASN handshake. |
| * @QCA_WLAN_VENDOR_ATTR_SECURE_RANGING_CTX_PEER_MAC_ADDR: The MAC address of |
| * the peer device for which secure ranging context is being configured. |
| * @QCA_WLAN_VENDOR_ATTR_SECURE_RANGING_CTX_SHA_TYPE: u32 attribute, defines the |
| * hash algorithm to be used, possible values are defined in enum |
| * qca_wlan_vendor_sha_type. |
| * @QCA_WLAN_VENDOR_ATTR_SECURE_RANGING_CTX_TK: Variable length attribute, holds |
| * the temporal key generated from the PASN handshake. The length of this |
| * attribute is dependent on the value of |
| * %QCA_WLAN_VENDOR_ATTR_SECURE_RANGING_CTX_CIPHER. |
| * @QCA_WLAN_VENDOR_ATTR_SECURE_RANGING_CTX_CIPHER: cipher suite to use with the |
| * TK, u32, as defined in IEEE Std 802.11-2020, 9.4.2.24.2 (Cipher suites) |
| * (e.g., 0x000FAC04). |
| * @QCA_WLAN_VENDOR_ATTR_SECURE_RANGING_CTX_LTF_KEYSEED: Variable length |
| * attribute, holds the LTF keyseed derived from KDK of PASN handshake. |
| * The length of this attribute is dependent on the value of |
| * %QCA_WLAN_VENDOR_ATTR_SECURE_RANGING_CTX_SHA_TYPE. |
| |
| */ |
| enum qca_wlan_vendor_attr_secure_ranging_ctx { |
| QCA_WLAN_VENDOR_ATTR_SECURE_RANGING_CTX_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_SECURE_RANGING_CTX_ACTION = 1, |
| QCA_WLAN_VENDOR_ATTR_SECURE_RANGING_CTX_SRC_ADDR = 2, |
| QCA_WLAN_VENDOR_ATTR_SECURE_RANGING_CTX_PEER_MAC_ADDR = 3, |
| QCA_WLAN_VENDOR_ATTR_SECURE_RANGING_CTX_SHA_TYPE = 4, |
| QCA_WLAN_VENDOR_ATTR_SECURE_RANGING_CTX_TK = 5, |
| QCA_WLAN_VENDOR_ATTR_SECURE_RANGING_CTX_CIPHER = 6, |
| QCA_WLAN_VENDOR_ATTR_SECURE_RANGING_CTX_LTF_KEYSEED = 7, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_SECURE_RANGING_CTX_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_SECURE_RANGING_CTX_MAX = |
| QCA_WLAN_VENDOR_ATTR_SECURE_RANGING_CTX_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_coap_offload_filter - Attributes used |
| * inside %QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_REPLY_FILTER |
| * nested attribute. The packets that match a filter will be replied with |
| * attributes configured in %QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_REPLY. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_FILTER_DEST_IPV4: |
| * u32 attribute. Destination IPv4 address in network byte order, the |
| * IPv4 packets with different address will be filtered out. |
| * This attribute is optional. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_FILTER_DEST_IPV4_IS_BC: |
| * Flag attribute. If it's present, indicates that |
| * %QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_FILTER_DEST_IPV4 is a broadcast |
| * address; while if not, indicates that the address is a unicast/multicast |
| * address. |
| * This attribute is optional. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_FILTER_DEST_IPV6: |
| * NLA_BINARY attribute, length is 16 bytes. |
| * Destination IPv6 address in network byte order, the IPv6 packets |
| * with different destination address will be filtered out. |
| * This attribute is optional. |
| * |
| * At least one of %QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_FILTER_DEST_IPV4 and |
| * %QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_FILTER_DEST_IPV6 must be configured. |
| * Packets on both IPv4 and IPv6 will be processed if both are configured. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_FILTER_DEST_PORT: |
| * u16 attribute. Destination UDP port, the packets with different destination |
| * UDP port will be filtered out. |
| * This attribute is mandatory. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_FILTER_MATCH_OFFSET: |
| * u32 attribute. Represents the offset (in UDP payload) of the data |
| * to be matched. |
| * This attribute is mandatory. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_FILTER_MATCH_DATA: |
| * NLA_BINARY attribute, the maximum allowed size is 16 bytes. |
| * Binary data that is compared bit-by-bit against the data (specified |
| * by %QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_FILTER_MATCH_OFFSET) in UDP |
| * payload, the packets don't match will be filtered out. |
| * This attribute is mandatory. |
| */ |
| enum qca_wlan_vendor_attr_coap_offload_filter { |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_FILTER_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_FILTER_DEST_IPV4 = 1, |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_FILTER_DEST_IPV4_IS_BC = 2, |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_FILTER_DEST_IPV6 = 3, |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_FILTER_DEST_PORT = 4, |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_FILTER_MATCH_OFFSET = 5, |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_FILTER_MATCH_DATA = 6, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_FILTER_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_FILTER_MAX = |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_FILTER_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_coap_offload_reply - Attributes used |
| * inside %QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_REPLY nested attribute. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_REPLY_SRC_IPV4: |
| * u32 attribute. Source address (in network byte order) for replying |
| * the matching broadcast/multicast IPv4 packets. |
| * This attribute is optional. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_REPLY_SRC_IPV6: |
| * NLA_BINARY attribute, length is 16 bytes. |
| * Source address (in network byte order) for replying the matching |
| * multicast IPv6 packets. |
| * This attribute is optional. |
| * |
| * For broadcast/multicast offload reply, one of |
| * %QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_REPLY_SRC_IPV4 and |
| * %QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_REPLY_SRC_IPV6 or both must be |
| * configured according to version of the IP address(es) configured in |
| * %QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_REPLY_FILTER; |
| * while for unicast case, firmware will take the destination IP address |
| * in the received matching packet as the source address for replying. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_REPLY_FILTER: |
| * Nested attribute. Filter for the received UDP packets, only the matching |
| * packets will be replied and cached. |
| * See enum qca_wlan_vendor_attr_coap_offload_filter for list of supported |
| * attributes. |
| * This attribute is mandatory. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_REPLY_MSG: |
| * NLA_BINARY attribute, the maximum allowed size is 1152 bytes. |
| * CoAP message (UDP payload) to be sent upon receiving matching packets. |
| * Firmware is responsible for adding any necessary protocol headers. |
| * This attribute is mandatory. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_REPLY_CACHE_EXPTIME: |
| * u32 attribute. Expiration time in milliseconds of the cached CoAP messages. |
| * A cached message will be dropped by firmware if it's expired. |
| * This attribute is optional. A default value of 40000 will be used in the |
| * absence of it. |
| */ |
| enum qca_wlan_vendor_attr_coap_offload_reply { |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_REPLY_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_REPLY_SRC_IPV4 = 1, |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_REPLY_SRC_IPV6 = 2, |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_REPLY_FILTER = 3, |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_REPLY_MSG = 4, |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_REPLY_CACHE_EXPTIME = 5, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_REPLY_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_REPLY_MAX = |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_REPLY_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_coap_offload_tx_ipv4 - Represents parameters for |
| * CoAP message (UDP) transmitting on IPv4. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV4_SRC_ADDR: |
| * u32 attribute. Source address (in network byte order) for transmitting |
| * packets on IPv4. |
| * This attribute is mandatory. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV4_SRC_PORT: |
| * u16 attribute. Source UDP port. |
| * This attribute is optional, a random port is taken if it's not present. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV4_DEST_ADDR: |
| * u32 attribute. Destination IPv4 address (in network byte order). |
| * This attribute is mandatory. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV4_DEST_IS_BC: |
| * Flag attribute. If it's present, indicates that |
| * %QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV4_DEST_ADDR is a broadcast |
| * address; while if not, indicates that the address is unicast/multicast |
| * address. |
| * This attribute is optional. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV4_DEST_PORT: |
| * u16 attribute. Destination UDP port. |
| * This attribute is mandatory. |
| */ |
| enum qca_wlan_vendor_attr_coap_offload_tx_ipv4 { |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV4_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV4_SRC_ADDR = 1, |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV4_SRC_PORT = 2, |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV4_DEST_ADDR = 3, |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV4_DEST_IS_BC = 4, |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV4_DEST_PORT = 5, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV4_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV4_MAX = |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV4_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_coap_offload_tx_ipv6 - Represents parameters for |
| * CoAP message (UDP) transmitting on IPv6. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV6_SRC_ADDR: |
| * NLA_BINARY attribute, length is 16 bytes. |
| * Source address (in network byte order) for transmitting packets on IPv6. |
| * This attribute is mandatory. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV6_SRC_PORT: |
| * u16 attribute. Source UDP port. |
| * This attribute is optional, a random port is taken if it's not present. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV6_DEST_ADDR: |
| * NLA_BINARY attribute, length is 16 bytes. |
| * Destination IPv6 address (in network byte order). |
| * This attribute is mandatory. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV6_DEST_PORT: |
| * u16 attribute. Destination UDP port. |
| * This attribute is mandatory. |
| */ |
| enum qca_wlan_vendor_attr_coap_offload_tx_ipv6 { |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV6_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV6_SRC_ADDR = 1, |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV6_SRC_PORT = 2, |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV6_DEST_ADDR = 3, |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV6_DEST_PORT = 4, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV6_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV6_MAX = |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_TX_IPV6_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_coap_offload_periodic_tx - Attributes used |
| * inside %QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_PERIODIC_TX nested attribute. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_PERIODIC_TX_IPV4: |
| * Nested attribute. The IPv4 source/destination address/port for offload |
| * transmitting. See enum qca_wlan_vendor_attr_coap_offload_tx_ipv4 for the list |
| * of supported attributes. |
| * This attribute is optional. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_PERIODIC_TX_IPV6: |
| * Nested attribute. The IPv6 source/destination address/port for offload |
| * transmitting. See enum qca_wlan_vendor_attr_coap_offload_tx_ipv6 for the list |
| * of supported attributes. |
| * This attribute is optional. |
| * |
| * At least one of %QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_PERIODIC_TX_IPV4 and |
| * %QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_PERIODIC_TX_IPV6 must be configured. |
| * Firmware will transmit the packets on both IPv4 and IPv6 if both are |
| * configured. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_PERIODIC_TX_PERIOD: |
| * u32 attribute. Period in milliseconds for the periodic transmitting. |
| * This attribute is mandatory. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_PERIODIC_TX_MSG: |
| * NLA_BINARY attribute, the maximum allowed size is 1152 bytes. |
| * CoAP message (UDP payload) to be periodically transmitted. Firmware |
| * is responsible for adding any necessary protocol headers. |
| * This attribute is mandatory. |
| */ |
| enum qca_wlan_vendor_attr_coap_offload_periodic_tx { |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_PERIODIC_TX_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_PERIODIC_TX_IPV4 = 1, |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_PERIODIC_TX_IPV6 = 2, |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_PERIODIC_TX_PERIOD = 3, |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_PERIODIC_TX_MSG = 4, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_PERIODIC_TX_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_PERIODIC_TX_MAX = |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_PERIODIC_TX_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_coap_offload_cache_info - Attributes used |
| * inside %QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_CACHES nested attribute. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_CACHE_INFO_TS: |
| * u64 attribute. Received time (since system booted in microseconds) of |
| * the cached CoAP message. |
| * This attribute is mandatory. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_CACHE_INFO_SRC_IPV4: |
| * u32 attribute. Source IPv4 address (in network byte order) of the cached |
| * CoAP message. |
| * This attribute is optional. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_CACHE_INFO_SRC_IPV6: |
| * NLA_BINARY attribute, length is 16 bytes. |
| * Source IPv6 address (in network byte order) of the cached CoAP message. |
| * This attribute is optional. |
| * |
| * At most and at least one of |
| * %QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_CACHE_INFO_SRC_IPV4 and |
| * %QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_CACHE_INFO_SRC_IPV6 is given for |
| * an entry. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_CACHE_INFO_MSG: |
| * NLA_BINARY attribute, the maximum allowed size is 1152 bytes. |
| * The cached CoAP message (UDP payload). If the actual message size is |
| * greater than the maximum size, it will be truncated and leaving only |
| * the first 1152 bytes. |
| * This attribute is mandatory. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_CACHE_INFO_PAD: Attribute used for |
| * padding for 64-bit alignment |
| */ |
| enum qca_wlan_vendor_attr_coap_offload_cache_info { |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_CACHE_INFO_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_CACHE_INFO_TS = 1, |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_CACHE_INFO_SRC_IPV4 = 2, |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_CACHE_INFO_SRC_IPV6 = 3, |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_CACHE_INFO_MSG = 4, |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_CACHE_INFO_PAD = 5, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_CACHE_INFO_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_CACHE_INFO_MAX = |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_CACHE_INFO_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_coap_offload_action - Actions for |
| * vendor command QCA_NL80211_VENDOR_SUBCMD_COAP_OFFLOAD. |
| * |
| * @QCA_WLAN_VENDOR_COAP_OFFLOAD_ACTION_REPLY_ENABLE: |
| * Enable CoAP offload reply. |
| * If it's enabled, firmware will start offload processing on each suspend |
| * and stop on each resume. |
| * |
| * Offload reply on match works as follows: |
| * Reply the packets that match the filter with the given CoAP |
| * message (with necessary protocol headers), increase the CoAP message |
| * ID in the given CoAP message by one for the next use after each successful |
| * transmission, and try to store the information of the received packet, |
| * including the received time, source IP address, and CoAP message (UDP |
| * payload). |
| * |
| * Firmware has a limit to the maximum stored entries, it takes the source IP |
| * address as the key of an entry, and keeps at most one entry for each key. |
| * A packet won't be stored if no entry for the same key is present and the |
| * total number of the existing unexpired entries reaches the maximum value. |
| * |
| * If any configured item is changed, user space should disable offload reply |
| * first and then issue a new enable request. |
| * |
| * @QCA_WLAN_VENDOR_COAP_OFFLOAD_ACTION_REPLY_DISABLE: |
| * Disable CoAP offload reply and return information of any cached CoAP |
| * messages. |
| * |
| * @QCA_WLAN_VENDOR_COAP_OFFLOAD_ACTION_PERIODIC_TX_ENABLE: |
| * Enable CoAP offload periodic transmitting. |
| * If it's enabled, firmware will start offload periodic transmitting on |
| * each suspend and stop on each resume. |
| * |
| * Offload periodic transmitting works as follows: |
| * Send the given CoAP message (with necessary protocol headers) with the given |
| * source/destination IP address/UDP port periodically based on the given |
| * period and increase the CoAP message ID in the given CoAP message by one |
| * for the next use after each successful transmission. |
| * |
| * If any configured item is changed, user space should disable offload |
| * periodic transmitting first and then issue a new enable request. |
| * |
| * @QCA_WLAN_VENDOR_COAP_OFFLOAD_ACTION_PERIODIC_TX_DISABLE: |
| * Disable CoAP offload periodic transmitting. |
| * |
| * @QCA_WLAN_VENDOR_COAP_OFFLOAD_ACTION_CACHE_GET: |
| * Get information of the CoAP messages cached during offload reply |
| * processing. The cache is cleared after retrieval. |
| */ |
| enum qca_wlan_vendor_coap_offload_action { |
| QCA_WLAN_VENDOR_COAP_OFFLOAD_ACTION_REPLY_ENABLE = 0, |
| QCA_WLAN_VENDOR_COAP_OFFLOAD_ACTION_REPLY_DISABLE = 1, |
| QCA_WLAN_VENDOR_COAP_OFFLOAD_ACTION_PERIODIC_TX_ENABLE = 2, |
| QCA_WLAN_VENDOR_COAP_OFFLOAD_ACTION_PERIODIC_TX_DISABLE = 3, |
| QCA_WLAN_VENDOR_COAP_OFFLOAD_ACTION_CACHE_GET = 4, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_coap_offload - Used by the |
| * vendor command QCA_NL80211_VENDOR_SUBCMD_COAP_OFFLOAD. |
| * This is used to set parameters for CoAP offload processing, or get |
| * cached CoAP messages from firmware. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_ACTION: |
| * u32 attribute. Action to take in this vendor command. |
| * See enum qca_wlan_vendor_coap_offload_action for supported actions. |
| * This attribute is mandatory. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_REQ_ID: |
| * u32 attribute. Represents the Request ID for the CoAP offload |
| * configuration, which can help to identify the user entity starting |
| * the CoAP offload processing and accordingly stop the respective |
| * ones/get the cached CoAP messages with the matching ID. |
| * This attribute is mandatory. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_REPLY: |
| * Nested attribute. Parameters for offload reply. |
| * See enum qca_wlan_vendor_attr_coap_offload_reply for the list of |
| * supported attributes. |
| * This attribute is mandatory if %QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_ACTION |
| * is QCA_WLAN_VENDOR_COAP_OFFLOAD_ACTION_REPLY_ENABLE, and is ignored |
| * otherwise. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_PERIODIC_TX: |
| * Nested attribute. Parameters for offload periodic transmitting. |
| * See enum qca_wlan_vendor_attr_coap_offload_periodic_tx for the list of |
| * supported attributes. |
| * This attribute is mandatory if %QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_ACTION is |
| * QCA_WLAN_VENDOR_COAP_OFFLOAD_ACTION_PERIODIC_TX_ENABLE, and is ignored |
| * otherwise. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_CACHES: |
| * Array of nested attributes. Information of the cached CoAP messages, |
| * where each entry is taken from |
| * enum qca_wlan_vendor_attr_coap_offload_cache_info. |
| * This attribute is used for reporting the cached CoAP messages |
| * in reply for command in which %QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_ACTION |
| * is QCA_WLAN_VENDOR_COAP_OFFLOAD_ACTION_CACHE_GET or |
| * QCA_WLAN_VENDOR_COAP_OFFLOAD_ACTION_REPLY_DISABLE. It means there is no |
| * cached item if this attribute is not present. |
| */ |
| enum qca_wlan_vendor_attr_coap_offload { |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_ACTION = 1, |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_REQ_ID = 2, |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_REPLY = 3, |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_PERIODIC_TX = 4, |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_CACHES = 5, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_MAX = |
| QCA_WLAN_VENDOR_ATTR_COAP_OFFLOAD_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_scs_rule_config - Used by the vendor command |
| * QCA_NL80211_VENDOR_SUBCMD_SCS_RULE_CONFIG to configure Stream Classification |
| * Service (SCS) rule. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_RULE_ID: Mandatory u32 attribute. |
| * Represents the unique id of SCS rule to be configured. |
| |
| * @QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_REQUEST_TYPE: Mandatory u8 attribute. |
| * Represents the request type: add, remove, or change. |
| * Values as defined in IEEE Std 802.11-2020, Table 9-246 (SCS Request |
| * Type definitions). |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_OUTPUT_TID: Mandatory u8 attribute |
| * in case of add/change request type. |
| * Represents the output traffic identifier (TID) to be assigned to the flow |
| * matching the rule. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_CLASSIFIER_TYPE: Mandatory u8 |
| * attribute in case of add/change request type. |
| * Represents type of classifier parameters present in SCS rule. |
| * Refer IEEE Std 802.11-2020 Table 9-164 (Frame classifier type). |
| * Only classifier types 4 and 10 are supported for SCS. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS4_VERSION: Mandatory u8 attribute |
| * in case of add/change request type when classifier type is TCLAS4. |
| * Represents the IP version (4: IPv4, 6: IPv6) of the rule. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS4_SRC_IPV4_ADDR: Optional |
| * attribute in case of add/change request type when classifier type is TCLAS4 |
| * and version attribute is IPv4. |
| * Represents the source IPv4 address in the rule which is to be compared |
| * against the source IP address in the IPv4 header. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS4_DST_IPV4_ADDR: Optional |
| * attribute in case of add/change request type when classifier type is TCLAS4 |
| * and version attribute is IPv4. |
| * Represents the destination IPv4 address in the rule which is to be compared |
| * against the destination IP address in the IPv4 header. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS4_SRC_IPV6_ADDR: Optional |
| * attribute in case of add/change request type when classifier type is TCLAS4 |
| * and version attribute is IPv6. |
| * Represents the source IPv6 address in the rule which is to be compared |
| * against the source IP address in the IPv6 header. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS4_DST_IPV6_ADDR: Optional |
| * attribute in case of add/change request type when classifier type is TCLAS4 |
| * and version attribute is IPv6. |
| * Represents the destination IPv6 address in the rule which is to be compared |
| * against the destination IP address in the IPv6 header. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS4_SRC_PORT: Optional u16 attribute |
| * in case of add/change request type when classifier type is TCLAS4. |
| * Represents the source port number in the rule which is to be compared against |
| * the source port number in the protocol header. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS4_DST_PORT: Optional u16 attribute |
| * in case of add/change request type when classifier type is TCLAS4. |
| * Represents the destination port number in the rule which is to be compared |
| * against the destination port number in the protocol header. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS4_DSCP: Optional u8 attribute |
| * in case of add/change request type when classifier type is TCLAS4. |
| * Represents the DSCP value in the rule which is to be compared against the |
| * DSCP field present in the IP header. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS4_NEXT_HEADER: Optional u8 |
| * attribute in case of add/change request type when classifier type is TCLAS4. |
| * Represents the protocol/next header in the rule which is to be compared |
| * against the protocol/next header field present in the IPv4/IPv6 header. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS4_FLOW_LABEL: Optional |
| * attribute of size 3 bytes present in case of add/change request type |
| * when classifier type is TCLAS4 and version is IPv6. |
| * Represents the flow label value in the rule which is to be compared against |
| * the flow label field present in the IPv6 header. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS10_PROTOCOL_INSTANCE: Optional u8 |
| * attribute in case of add/change request type when classifier type is TCLAS10. |
| * Represents the protocol instance number in the rule. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS10_NEXT_HEADER: Optional u8 |
| * attribute in case of add/change request type when classifier type is TCLAS10. |
| * Represents the protocol/next header in the rule which is to be compared |
| * against the protocol/next header field present in the IPv4/IPv6 header. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS10_FILTER_MASK: Optional |
| * attribute of variable length present when request type is add/change and |
| * classifier type is TCLAS10. |
| * Represents the mask to be used for masking the header contents of the header |
| * specified by QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS10_NEXT_HEADER |
| * attribute. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS10_FILTER_VALUE: Optional |
| * attribute of variable length present when request type is add/change and |
| * classifier type is TCLAS10. |
| * Represents the value to be compared against after masking the header contents |
| * of the header specified by the |
| * QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS10_NEXT_HEADER attribute with the |
| * filter mask specified by the |
| * QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS10_FILTER_MASK attribute. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_SERVICE_CLASS_ID: Optional u16 |
| * attribute. |
| * Represents the service class id of the configured SCS rule. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_DST_MAC_ADDR: Optional 6 bytes |
| * MAC address. |
| * Represents the destination MAC address in the rule. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_NETDEV_IF_INDEX: Optional u32 attribute |
| * Represents the netdevice interface index in the rule. |
| */ |
| enum qca_wlan_vendor_attr_scs_rule_config { |
| QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_RULE_ID = 1, |
| QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_REQUEST_TYPE = 2, |
| QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_OUTPUT_TID = 3, |
| QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_CLASSIFIER_TYPE = 4, |
| QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS4_VERSION = 5, |
| QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS4_SRC_IPV4_ADDR = 6, |
| QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS4_DST_IPV4_ADDR = 7, |
| QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS4_SRC_IPV6_ADDR = 8, |
| QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS4_DST_IPV6_ADDR = 9, |
| QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS4_SRC_PORT = 10, |
| QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS4_DST_PORT = 11, |
| QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS4_DSCP = 12, |
| QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS4_NEXT_HEADER = 13, |
| QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS4_FLOW_LABEL = 14, |
| QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS10_PROTOCOL_INSTANCE = 15, |
| QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS10_NEXT_HEADER = 16, |
| QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS10_FILTER_MASK = 17, |
| QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_TCLAS10_FILTER_VALUE = 18, |
| QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_SERVICE_CLASS_ID = 19, |
| QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_DST_MAC_ADDR = 20, |
| QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_NETDEV_IF_INDEX = 21, |
| |
| /* Keep last */ |
| QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_MAX = |
| QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_mlo_links - Definition of attributes used inside |
| * nested attribute QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_MLO_LINKS. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_MLO_LINK_ID: u8 attribute, link ID of this MLO link. |
| * @QCA_WLAN_VENDOR_ATTR_MLO_LINK_MAC_ADDR: Own MAC address of this MLO link. |
| * @QCA_WLAN_VENDOR_ATTR_MLO_LINK_BSSID: AP link MAC address of this MLO link. |
| */ |
| enum qca_wlan_vendor_attr_mlo_links { |
| QCA_WLAN_VENDOR_ATTR_MLO_LINK_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_MLO_LINK_ID = 1, |
| QCA_WLAN_VENDOR_ATTR_MLO_LINK_MAC_ADDR = 2, |
| QCA_WLAN_VENDOR_ATTR_MLO_LINK_BSSID = 3, |
| |
| /* Keep last */ |
| QCA_WLAN_VENDOR_ATTR_MLO_LINK_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_MLO_LINK_MAX = |
| QCA_WLAN_VENDOR_ATTR_MLO_LINK_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_sar_version - This describes the current SAR version |
| * used in the firmware. |
| * |
| * @QCA_WLAN_VENDOR_SAR_VERSION_1: The firmware supports legacy SAR. |
| * In legacy SAR, the firmware supports 5 static and 1 user defined SAR limits. |
| * |
| * @QCA_WLAN_VENDOR_SAR_VERSION_2: The firmware supports SAR version 2, |
| * i.e., SAR Non DBS mode. In SAR version 2, the firmware has 6 SAR tables for |
| * each CTL group. So user can select up to 6 SAR indexes from the current CTL |
| * groups. |
| * |
| * @QCA_WLAN_VENDOR_SAR_VERSION_3: The firmware supports SAR version 3, |
| * i.e., SAR DBS mode. In SAR version 3, the firmware has 6 SAR tables for each |
| * CTL group but user can choose up to 3 SAR set index only, as the top half |
| * of the SAR index (0 to 2) is used for non DBS purpose and the bottom half of |
| * the SAR index (3 to 5) is used for DBS mode. |
| */ |
| enum qca_wlan_vendor_sar_version { |
| QCA_WLAN_VENDOR_SAR_VERSION_INVALID = 0, |
| QCA_WLAN_VENDOR_SAR_VERSION_1 = 1, |
| QCA_WLAN_VENDOR_SAR_VERSION_2 = 2, |
| QCA_WLAN_VENDOR_SAR_VERSION_3 = 3, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_sar_ctl_group_state - This describes whether |
| * CTL grouping is enabled or disabled in the firmware. |
| * |
| * @QCA_WLAN_VENDOR_SAR_CTL_GROUP_STATE_ENABLED: CTL grouping |
| * is enabled in firmware. |
| * |
| * @QCA_WLAN_VENDOR_SAR_CTL_GROUP_STATE_DISABLED: CTL grouping |
| * is disabled in firmware. |
| * |
| */ |
| enum qca_wlan_vendor_sar_ctl_group_state { |
| QCA_WLAN_VENDOR_SAR_CTL_GROUP_STATE_INVALID = 0, |
| QCA_WLAN_VENDOR_SAR_CTL_GROUP_STATE_ENABLED = 1, |
| QCA_WLAN_VENDOR_SAR_CTL_GROUP_STATE_DISABLED = 2, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_sar_capability - Used by the vendor command |
| * QCA_NL80211_VENDOR_SUBCMD_GET_SAR_CAPABILITY to get SAR capabilities |
| * supported by the firmware. |
| |
| * @QCA_WLAN_VENDOR_ATTR_SAR_CAPABILITY_VERSION: |
| * u32 attribute. This field describes current SAR version supported by the |
| * firmware. |
| * See enum qca_wlan_vendor_sar_version for more information. |
| * This attribute is mandatory. |
| |
| * @QCA_WLAN_VENDOR_ATTR_SAR_CAPABILITY_CTL_GROUP_STATE: |
| * u32 attribute. This field describes whether CTL groups are enabled |
| * or disabled in the firmware. |
| * See enum qca_wlan_vendor_sar_ctl_group_state for more information. |
| * This attribute is optional. |
| */ |
| |
| enum qca_wlan_vendor_attr_sar_capability { |
| QCA_WLAN_VENDOR_ATTR_SAR_CAPABILITY_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_SAR_CAPABILITY_VERSION = 1, |
| QCA_WLAN_VENDOR_ATTR_SAR_CAPABILITY_CTL_GROUP_STATE = 2, |
| |
| /* Keep last */ |
| QCA_WLAN_VENDOR_ATTR_SAR_CAPABILITY_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_SAR_CAPABILITY_MAX = |
| QCA_WLAN_VENDOR_ATTR_SAR_CAPABILITY_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_sr_stats - Attributes for Spatial Reuse statistics. |
| * These statistics are sent from the driver in a response when userspace |
| * queries to get the statistics using the operation |
| * %QCA_WLAN_SR_OPERATION_GET_STATS. These statistics are reset |
| * by the driver when the SR feature is enabled, when the driver receives |
| * %QCA_WLAN_SR_OPERATION_CLEAR_STATS operation, or when disconnected. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SR_STATS_NON_SRG_TX_OPPORTUNITIES_COUNT: u32 attribute. |
| * Mandatory only when non-SRG is supported by the AP and optional otherwise. |
| * This represents the number of non-SRG TX opportunities. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SR_STATS_NON_SRG_TX_PPDU_TRIED_COUNT: u32 attribute. |
| * Mandatory only when non-SRG is supported by the AP and optional otherwise. |
| * This represents the number of non-SRG PPDUs tried to transmit. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SR_STATS_NON_SRG_TX_PPDU_SUCCESS_COUNT: u32 attribute. |
| * Mandatory only when non-SRG is supported by the AP and optional otherwise. |
| * This represents the number of non-SRG PPDUs successfully transmitted. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SR_STATS_SRG_TX_OPPORTUNITIES_COUNT: u32 attribute. |
| * Mandatory only when SRG is supported by the AP and optional otherwise. |
| * This represents the number of SRG TX opportunities. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SR_STATS_SRG_TX_PPDU_TRIED_COUNT: u32 attribute. |
| * Mandatory only when SRG is supported by the AP and optional otherwise. |
| * This represents the number of SRG PPDUs tried to transmit. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SR_STATS_SRG_TX_PPDU_SUCCESS_COUNT: u32 attribute. |
| * Mandatory only when SRG is supported by the AP and optional otherwise. |
| * This represents the number of SRG PPDUs successfully transmitted. |
| */ |
| enum qca_wlan_vendor_attr_sr_stats { |
| QCA_WLAN_VENDOR_ATTR_SR_STATS_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_SR_STATS_NON_SRG_TX_OPPORTUNITIES_COUNT = 1, |
| QCA_WLAN_VENDOR_ATTR_SR_STATS_NON_SRG_TX_PPDU_TRIED_COUNT = 2, |
| QCA_WLAN_VENDOR_ATTR_SR_STATS_NON_SRG_TX_PPDU_SUCCESS_COUNT = 3, |
| QCA_WLAN_VENDOR_ATTR_SR_STATS_SRG_TX_OPPORTUNITIES_COUNT = 4, |
| QCA_WLAN_VENDOR_ATTR_SR_STATS_SRG_TX_PPDU_TRIED_COUNT = 5, |
| QCA_WLAN_VENDOR_ATTR_SR_STATS_SRG_TX_PPDU_SUCCESS_COUNT = 6, |
| |
| /* Keep last */ |
| QCA_WLAN_VENDOR_ATTR_SR_STATS_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_SR_STATS_MAX = |
| QCA_WLAN_VENDOR_ATTR_SR_STATS_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_sr_reason_code - Defines the different reason codes used in |
| * Spatial Reuse feature. |
| * |
| * @QCA_WLAN_SR_REASON_CODE_ROAMING: The SR feature is disabled/enabled due to |
| * roaming to an AP that doesn't support/supports SR feature, respectively. |
| * |
| * @QCA_WLAN_SR_REASON_CODE_CONCURRENCY: The SR feature is disabled/enabled due |
| * to change in concurrent interfaces that are supported by the driver. |
| */ |
| enum qca_wlan_sr_reason_code { |
| QCA_WLAN_SR_REASON_CODE_ROAMING = 0, |
| QCA_WLAN_SR_REASON_CODE_CONCURRENCY = 1, |
| }; |
| |
| /** |
| * enum qca_wlan_sr_operation - Defines the different types of SR operations. |
| * The values are used inside attribute %QCA_WLAN_VENDOR_ATTR_SR_OPERATION. |
| * |
| * @QCA_WLAN_SR_OPERATION_SR_ENABLE: Userspace sends this operation to the |
| * driver to enable the Spatial Reuse feature. Attributes |
| * %QCA_WLAN_VENDOR_ATTR_SR_PARAMS_SRG_PD_THRESHOLD and |
| * %QCA_WLAN_VENDOR_ATTR_SR_PARAMS_NON_SRG_PD_THRESHOLD are used with this |
| * operation. |
| * |
| * @QCA_WLAN_SR_OPERATION_SR_DISABLE: Userspace sends this operation to the |
| * driver to disable the Spatial Reuse feature. |
| * |
| * @QCA_WLAN_SR_OPERATION_SR_SUSPEND: The driver uses this operation in an |
| * asynchronous event sent to userspace when the SR feature is disabled. |
| * The disable reason is encoded in QCA_WLAN_VENDOR_ATTR_SR_PARAMS_REASON_CODE |
| * and sent along with the asynchronous event. |
| * |
| * @QCA_WLAN_SR_OPERATION_SR_RESUME: The driver uses this operation in an |
| * asynchronous event when the SR feature is enabled again after the SR feature |
| * was suspended by the driver earlier. The enable reason is |
| * encoded in QCA_WLAN_VENDOR_ATTR_SR_PARAMS_REASON_CODE. Attributes used are |
| * %QCA_WLAN_VENDOR_ATTR_SR_PARAMS_SRG_PD_THRESHOLD and |
| * %QCA_WLAN_VENDOR_ATTR_SR_PARAMS_NON_SRG_PD_THRESHOLD. |
| * |
| * @QCA_WLAN_SR_OPERATION_PSR_AND_NON_SRG_OBSS_PD_PROHIBIT: This operation is |
| * used to prohibit PSR-based spatial reuse and non-SRG OBSS PD-based spatial |
| * reuse transmissions. Userspace sends this operation to the driver. |
| * The driver/firmware upon receiving this operation shall prohibit PSR-based |
| * spatial reuse and non-SRG OBSS PD-based spatial reuse transmissions. |
| * |
| * @QCA_WLAN_SR_OPERATION_PSR_AND_NON_SRG_OBSS_PD_ALLOW: This operation is |
| * used to allow PSR-based spatial reuse and non-SRG OBSS PD-based spatial |
| * reuse transmissions. Userspace sends this operation to the driver. |
| * The driver/firmware upon receiving this operation shall allow PSR-based |
| * spatial reuse and non-SRG OBSS PD-based spatial reuse transmissions. |
| * |
| * @QCA_WLAN_SR_OPERATION_GET_STATS: Userspace sends this operation to the |
| * driver to get the SR statistics and the driver sends a synchronous response |
| * with the attributes defined in enum qca_wlan_vendor_attr_sr_stats using the |
| * nested attribute %QCA_WLAN_VENDOR_ATTR_SR_STATS. |
| * |
| * @QCA_WLAN_SR_OPERATION_CLEAR_STATS: Userspace sends this operation to the |
| * driver to clear the SR statistics and upon receiving this operation |
| * the driver/firmware shall clear the SR statistics. |
| * |
| * @QCA_WLAN_SR_OPERATION_GET_PARAMS: Userspace sends this operation to the |
| * driver to get the SR parameters and the driver sends the synchronous response |
| * with the following required attributes: |
| * %QCA_WLAN_VENDOR_ATTR_SR_PARAMS_SRG_OBSS_PD_MIN_OFFSET, |
| * %QCA_WLAN_VENDOR_ATTR_SR_PARAMS_SRG_OBSS_PD_MAX_OFFSET, |
| * %QCA_WLAN_VENDOR_ATTR_SR_PARAMS_NON_SRG_OBSS_PD_MAX_OFFSET, |
| * %QCA_WLAN_VENDOR_ATTR_SR_PARAMS_HESIGA_VAL15_ENABLE, |
| * %QCA_WLAN_VENDOR_ATTR_SR_PARAMS_NON_SRG_OBSS_PD_DISALLOW. |
| * |
| * @QCA_WLAN_SR_OPERATION_UPDATE_PARAMS: The driver uses this operation in an |
| * asynchronous event to userspace to update any changes in SR parameters. |
| * The following attributes are used with this operation: |
| * %QCA_WLAN_VENDOR_ATTR_SR_PARAMS_SRG_OBSS_PD_MIN_OFFSET, |
| * %QCA_WLAN_VENDOR_ATTR_SR_PARAMS_SRG_OBSS_PD_MAX_OFFSET, |
| * %QCA_WLAN_VENDOR_ATTR_SR_PARAMS_NON_SRG_OBSS_PD_MAX_OFFSET, |
| * %QCA_WLAN_VENDOR_ATTR_SR_PARAMS_HESIGA_VAL15_ENABLE, |
| * %QCA_WLAN_VENDOR_ATTR_SR_PARAMS_NON_SRG_OBSS_PD_DISALLOW. |
| */ |
| enum qca_wlan_sr_operation { |
| QCA_WLAN_SR_OPERATION_SR_ENABLE = 0, |
| QCA_WLAN_SR_OPERATION_SR_DISABLE = 1, |
| QCA_WLAN_SR_OPERATION_SR_SUSPEND = 2, |
| QCA_WLAN_SR_OPERATION_SR_RESUME = 3, |
| QCA_WLAN_SR_OPERATION_PSR_AND_NON_SRG_OBSS_PD_PROHIBIT = 4, |
| QCA_WLAN_SR_OPERATION_PSR_AND_NON_SRG_OBSS_PD_ALLOW = 5, |
| QCA_WLAN_SR_OPERATION_GET_STATS = 6, |
| QCA_WLAN_SR_OPERATION_CLEAR_STATS = 7, |
| QCA_WLAN_SR_OPERATION_GET_PARAMS = 8, |
| QCA_WLAN_SR_OPERATION_UPDATE_PARAMS = 9, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_sr_params - Defines attributes for SR configuration |
| * parameters used by attribute %QCA_WLAN_VENDOR_ATTR_SR_PARAMS. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SR_PARAMS_HESIGA_VAL15_ENABLE: Flag attribute. |
| * This attribute is optionally set in response to |
| * %QCA_WLAN_SR_OPERATION_GET_PARAMS and in request when operation is set to |
| * %QCA_WLAN_SR_OPERATION_PSR_AND_NON_SRG_OBSS_PD_PROHIBIT. Refer IEEE Std |
| * 802.11ax-2021 Figure 9-788r-SR Control field format to understand more |
| * about HESIGA_Spatial_reuse_value15_allowed. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SR_PARAMS_NON_SRG_OBSS_PD_DISALLOW: Flag attribute. |
| * This attribute is used in response to %QCA_WLAN_SR_OPERATION_GET_PARAMS |
| * operation. This indicates whether non-SRG OBSS PD SR transmissions are |
| * allowed or not at non-AP STAs that are associated with the AP. If present |
| * non-SRG OBSS PD SR transmissions are not allowed else are allowed. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SR_PARAMS_SRG_OBSS_PD_MIN_OFFSET: Optional u8 |
| * attribute. This attribute is used in response to |
| * %QCA_WLAN_SR_OPERATION_GET_PARAMS operation. This indicates the SRG OBSS PD |
| * Min Offset field which contains an unsigned integer that is added to -82 dBm |
| * to generate the value of the SRG OBSS PD Min parameter. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SR_PARAMS_SRG_OBSS_PD_MAX_OFFSET: Optional u8 |
| * attribute. This attribute is used in response to |
| * %QCA_WLAN_SR_OPERATION_GET_PARAMS operation. This indicates the SRG OBSS PD |
| * Max Offset field which contains an unsigned integer that is added to -82 dBm |
| * to generate the value of the SRG OBSS PD Max parameter. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SR_PARAMS_NON_SRG_OBSS_PD_MAX_OFFSET: Optional u8 |
| * attribute. This attribute is used in response to |
| * %QCA_WLAN_SR_OPERATION_GET_PARAMS operation. This indicates the Non-SRG OBSS |
| * PD Max Offset field which contains an unsigned integer that is added to -82 |
| * dBm to generate the value of the Non-SRG OBSS PD Max parameter. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SR_PARAMS_SRG_PD_THRESHOLD: s32 attribute (in dBm). |
| * Userspace optionally sends this attribute with |
| * %QCA_WLAN_SR_OPERATION_SR_ENABLE operation to the driver to specify the |
| * preferred SRG PD threshold. The driver shall send this attribute to |
| * userspace in SR resume event to indicate the PD threshold being used for SR. |
| * When there is change in SRG PD threshold (for example, due to roaming, etc.) |
| * the driver shall indicate the userspace the newly configured SRG PD threshold |
| * using an asynchronous event. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SR_PARAMS_NON_SRG_PD_THRESHOLD: s32 attribute (in dBm). |
| * Userspace optionally sends this attribute with |
| * %QCA_WLAN_SR_OPERATION_SR_ENABLE operation to the driver to specify the |
| * preferred non-SRG PD threshold. The driver shall send this attribute to |
| * userspace in SR resume event to indicate the PD threshold being used for SR. |
| * When there is change in non-SRG PD threshold (for example, due to roaming, |
| * etc.) the driver shall indicate the userspace the newly configured non-SRG PD |
| * threshold using an asynchronous event. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SR_PARAMS_REASON_CODE: u32 attribute. The possible |
| * values are defined in enum qca_wlan_sr_reason_code. This |
| * attribute is used with %QCA_WLAN_SR_OPERATION_SR_RESUME and |
| * %QCA_WLAN_SR_OPERATION_SR_SUSPEND operations. |
| */ |
| enum qca_wlan_vendor_attr_sr_params { |
| QCA_WLAN_VENDOR_ATTR_SR_PARAMS_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_SR_PARAMS_HESIGA_VAL15_ENABLE = 1, |
| QCA_WLAN_VENDOR_ATTR_SR_PARAMS_NON_SRG_OBSS_PD_DISALLOW = 2, |
| QCA_WLAN_VENDOR_ATTR_SR_PARAMS_SRG_OBSS_PD_MIN_OFFSET = 3, |
| QCA_WLAN_VENDOR_ATTR_SR_PARAMS_SRG_OBSS_PD_MAX_OFFSET = 4, |
| QCA_WLAN_VENDOR_ATTR_SR_PARAMS_NON_SRG_OBSS_PD_MAX_OFFSET = 5, |
| QCA_WLAN_VENDOR_ATTR_SR_PARAMS_SRG_PD_THRESHOLD = 6, |
| QCA_WLAN_VENDOR_ATTR_SR_PARAMS_NON_SRG_PD_THRESHOLD = 7, |
| QCA_WLAN_VENDOR_ATTR_SR_PARAMS_REASON_CODE = 8, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_SR_PARAMS_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_SR_PARAMS_MAX = |
| QCA_WLAN_VENDOR_ATTR_SR_PARAMS_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_sr - Defines the attributes used by the vendor |
| * command QCA_NL80211_VENDOR_SUBCMD_SR. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SR_OPERATION: Mandatory u8 attribute for all requests |
| * from userspace to the driver. Possible values are defined in enum |
| * qca_wlan_sr_operation. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SR_PARAMS: Nested attribute, contains the SR |
| * configuration parameters. The possible attributes inside this attribute are |
| * defined in enum qca_wlan_vendor_attr_sr_params. |
| * This attribute is used when QCA_WLAN_VENDOR_ATTR_SR_OPERATION is set to |
| * %QCA_WLAN_SR_OPERATION_SR_ENABLE in requests from userspace to the driver and |
| * also in response from the driver to userspace when the response is sent for |
| * %QCA_WLAN_SR_OPERATION_GET_PARAMS. |
| * The driver uses this attribute in asynchronous events in which the operation |
| * is set to %QCA_WLAN_SR_OPERATION_SR_RESUME, |
| * %QCA_WLAN_SR_OPERATION_SR_SUSPEND or %QCA_WLAN_SR_OPERATION_UPDATE_PARAMS. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SR_STATS: Nested attribute, contains the SR |
| * statistics. These attributes used inside this are defined in enum |
| * qca_wlan_vendor_attr_sr_stats. |
| * This attribute is used in response from the driver to a command in which |
| * %QCA_WLAN_VENDOR_ATTR_SR_OPERATION is set to |
| * %QCA_WLAN_SR_OPERATION_GET_STATS. |
| */ |
| enum qca_wlan_vendor_attr_sr { |
| QCA_WLAN_VENDOR_ATTR_SR_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_SR_OPERATION = 1, |
| QCA_WLAN_VENDOR_ATTR_SR_PARAMS = 2, |
| QCA_WLAN_VENDOR_ATTR_SR_STATS = 3, |
| |
| /* Keep last */ |
| QCA_WLAN_VENDOR_ATTR_SR_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_SR_MAX = |
| QCA_WLAN_VENDOR_ATTR_SR_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_mlo_peer_prim_netdev_event - Defines the attributes |
| * used in the QCA_NL80211_VENDOR_SUBCMD_MLO_PEER_PRIM_NETDEV_EVENT subcommand. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_MLO_PEER_PRIM_NETDEV_EVENT_MACADDR: 6 byte MAC address |
| * used by the peer on the link that corresponds to the link used for sending |
| * the event notification. |
| * @QCA_WLAN_VENDOR_ATTR_MLO_PEER_PRIM_NETDEV_EVENT_MLD_MAC_ADDR: 6 byte |
| * MLD MAC address of the peer. |
| * @QCA_WLAN_VENDOR_ATTR_MLO_PEER_PRIM_NETDEV_EVENT_PRIM_IFINDEX: u32 attribute, |
| * used to pass ifindex of the primary netdev. |
| */ |
| enum qca_wlan_vendor_attr_mlo_peer_prim_netdev_event { |
| QCA_WLAN_VENDOR_ATTR_MLO_PEER_PRIM_NETDEV_EVENT_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_MLO_PEER_PRIM_NETDEV_EVENT_MACADDR = 1, |
| QCA_WLAN_VENDOR_ATTR_MLO_PEER_PRIM_NETDEV_EVENT_MLD_MAC_ADDR = 2, |
| QCA_WLAN_VENDOR_ATTR_MLO_PEER_PRIM_NETDEV_EVENT_PRIM_IFINDEX = 3, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_MLO_PEER_PRIM_NETDEV_EVENT_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_MLO_PEER_PRIM_NETDEV_EVENT_MAX = |
| QCA_WLAN_VENDOR_ATTR_MLO_PEER_PRIM_NETDEV_EVENT_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_afc_freq_psd_info: This enum is used with |
| * nested attributes QCA_WLAN_VENDOR_ATTR_AFC_RESP_FREQ_PSD_INFO and |
| * QCA_WLAN_VENDOR_ATTR_AFC_EVENT_FREQ_RANGE_LIST to update the frequency range |
| * and PSD information. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_AFC_FREQ_PSD_INFO_RANGE_START: Required and type is |
| * u32. This attribute is used to indicate the start of the queried frequency |
| * range in MHz. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_AFC_FREQ_PSD_INFO_RANGE_END: Required and type is u32. |
| * This attribute is used to indicate the end of the queried frequency range |
| * in MHz. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_AFC_FREQ_PSD_INFO_PSD: Required and type is u32. |
| * This attribute will contain the PSD information for a single range as |
| * specified by the QCA_WLAN_VENDOR_ATTR_AFC_FREQ_PSD_INFO_RANGE_START and |
| * QCA_WLAN_VENDOR_ATTR_AFC_FREQ_PSD_INFO_RANGE_END attributes. |
| * |
| * The PSD power info (dBm/MHz) from user space should be multiplied |
| * by a factor of 100 when sending to the driver to preserve granularity |
| * up to 2 decimal places. |
| * Example: |
| * PSD power value: 10.21 dBm/MHz |
| * Value to be updated in QCA_WLAN_VENDOR_ATTR_AFC_PSD_INFO: 1021. |
| * |
| * Note: QCA_WLAN_VENDOR_ATTR_AFC_FREQ_PSD_INFO_PSD attribute will be used only |
| * with nested attribute QCA_WLAN_VENDOR_ATTR_AFC_RESP_FREQ_PSD_INFO and with |
| * QCA_WLAN_VENDOR_ATTR_AFC_EVENT_FREQ_RANGE_LIST when |
| * QCA_WLAN_VENDOR_ATTR_AFC_EVENT_TYPE is |
| * QCA_WLAN_VENDOR_AFC_EVENT_TYPE_POWER_UPDATE_COMPLETE. |
| * |
| * The following set of attributes will be used to exchange frequency and |
| * corresponding PSD information for AFC between the user space and the driver. |
| */ |
| enum qca_wlan_vendor_attr_afc_freq_psd_info { |
| QCA_WLAN_VENDOR_ATTR_AFC_FREQ_PSD_INFO_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_AFC_FREQ_PSD_INFO_RANGE_START = 1, |
| QCA_WLAN_VENDOR_ATTR_AFC_FREQ_PSD_INFO_RANGE_END = 2, |
| QCA_WLAN_VENDOR_ATTR_AFC_FREQ_PSD_INFO_PSD = 3, |
| |
| QCA_WLAN_VENDOR_ATTR_AFC_FREQ_PSD_INFO_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_AFC_FREQ_PSD_INFO_MAX = |
| QCA_WLAN_VENDOR_ATTR_AFC_FREQ_PSD_INFO_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_afc_chan_eirp_info: This enum is used with |
| * nested attribute QCA_WLAN_VENDOR_ATTR_AFC_CHAN_LIST_INFO to update the |
| * channel list and corresponding EIRP information. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_AFC_CHAN_EIRP_INFO_CHAN_NUM: Required and type is u8. |
| * This attribute is used to indicate queried channel from |
| * the operating class indicated in QCA_WLAN_VENDOR_ATTR_AFC_OPCLASS_INFO. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_AFC_CHAN_EIRP_INFO_EIRP: Optional and type is u32. |
| * This attribute is used to configure the EIRP power info corresponding |
| * to the channel number indicated in QCA_WLAN_VENDOR_ATTR_AFC_CHAN_NUM. |
| * The EIRP power info(dBm) from user space should be multiplied |
| * by a factor of 100 when sending to Driver to preserve granularity up to |
| * 2 decimal places. |
| * Example: |
| * EIRP power value: 34.23 dBm |
| * Value to be updated in QCA_WLAN_VENDOR_ATTR_AFC_EIRP_INFO: 3423. |
| * |
| * Note: QCA_WLAN_VENDOR_ATTR_AFC_EIRP_INFO attribute will only be used with |
| * nested attribute QCA_WLAN_VENDOR_ATTR_AFC_RESP_OPCLASS_CHAN_EIRP_INFO and |
| * with QCA_WLAN_VENDOR_ATTR_AFC_EVENT_OPCLASS_CHAN_LIST when |
| * QCA_WLAN_VENDOR_ATTR_AFC_EVENT_TYPE is |
| * QCA_WLAN_VENDOR_AFC_EVENT_TYPE_POWER_UPDATE_COMPLETE: |
| * |
| * The following set of attributes will be used to exchange Channel and |
| * corresponding EIRP information for AFC between the user space and Driver. |
| */ |
| enum qca_wlan_vendor_attr_afc_chan_eirp_info { |
| QCA_WLAN_VENDOR_ATTR_AFC_CHAN_EIRP_INFO_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_AFC_CHAN_EIRP_INFO_CHAN_NUM = 1, |
| QCA_WLAN_VENDOR_ATTR_AFC_CHAN_EIRP_INFO_EIRP = 2, |
| |
| QCA_WLAN_VENDOR_ATTR_AFC_CHAN_EIRP_INFO_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_AFC_CHAN_EIRP_INFO_MAX = |
| QCA_WLAN_VENDOR_ATTR_AFC_CHAN_EIRP_INFO_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_afc_opclass_info: This enum is used with nested |
| * attributes QCA_WLAN_VENDOR_ATTR_AFC_RESP_OPCLASS_CHAN_EIRP_INFO and |
| * QCA_WLAN_VENDOR_ATTR_AFC_REQ_OPCLASS_CHAN_INFO to update the operating class, |
| * channel, and EIRP related information. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_AFC_OPCLASS_INFO_OPCLASS: Required and type is u8. |
| * This attribute is used to indicate the operating class, as listed under |
| * IEEE Std 802.11-2020 Annex E Table E-4, for the queried channel list. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_AFC_OPCLASS_INFO_CHAN_LIST: Array of nested attributes |
| * for updating the channel number and EIRP power information. |
| * It uses the attributes defined in |
| * enum qca_wlan_vendor_attr_afc_chan_eirp_info. |
| * |
| * Operating class information packing format for |
| * QCA_WLAN_VENDOR_ATTR_AFC_EVENT_OPCLASS_CHAN_INFO when |
| * QCA_WLAN_VENDOR_ATTR_AFC_EVENT_TYPE is |
| * QCA_WLAN_VENDOR_ATTR_AFC_EVENT_TYPE_EXPIRY. |
| * |
| * m - Total number of operating classes. |
| * n, j - Number of queried channels for the corresponding operating class. |
| * |
| * QCA_WLAN_VENDOR_ATTR_AFC_OPCLASS_INFO_OPCLASS[0] |
| * QCA_WLAN_VENDOR_ATTR_AFC_OPCLASS_INFO_CHAN_LIST[0] |
| * QCA_WLAN_VENDOR_ATTR_AFC_CHAN_EIRP_INFO_CHAN_NUM[0] |
| * ..... |
| * QCA_WLAN_VENDOR_ATTR_AFC_CHAN_EIRP_INFO_CHAN_NUM[n - 1] |
| * .... |
| * QCA_WLAN_VENDOR_ATTR_AFC_OPCLASS_INFO_OPCLASS[m] |
| * QCA_WLAN_VENDOR_ATTR_AFC_OPCLASS_INFO_CHAN_LIST[m] |
| * QCA_WLAN_VENDOR_ATTR_AFC_CHAN_EIRP_INFO_CHAN_NUM[0] |
| * .... |
| * QCA_WLAN_VENDOR_ATTR_AFC_CHAN_EIRP_INFO_CHAN_NUM[j - 1] |
| * |
| * Operating class information packing format for |
| * QCA_WLAN_VENDOR_ATTR_AFC_RESP_OPCLASS_CHAN_EIRP_INFO and |
| * QCA_WLAN_VENDOR_ATTR_AFC_EVENT_OPCLASS_CHAN_INFO when |
| * QCA_WLAN_VENDOR_ATTR_AFC_EVENT_TYPE is |
| * QCA_WLAN_VENDOR_AFC_EVENT_TYPE_POWER_UPDATE_COMPLETE. |
| * |
| * m - Total number of operating classes. |
| * n, j - Number of channels for the corresponding operating class. |
| * |
| * QCA_WLAN_VENDOR_ATTR_AFC_OPCLASS_INFO_OPCLASS[0] |
| * QCA_WLAN_VENDOR_ATTR_AFC_OPCLASS_INFO_CHAN_LIST[0] |
| * QCA_WLAN_VENDOR_ATTR_AFC_CHAN_EIRP_INFO_CHAN_NUM[0] |
| * QCA_WLAN_VENDOR_ATTR_AFC_CHAN_EIRP_INFO_EIRP[0] |
| * ..... |
| * QCA_WLAN_VENDOR_ATTR_AFC_CHAN_EIRP_INFO_CHAN_NUM[n - 1] |
| * QCA_WLAN_VENDOR_ATTR_AFC_CHAN_EIRP_INFO_EIRP[n - 1] |
| * .... |
| * QCA_WLAN_VENDOR_ATTR_AFC_OPCLASS_INFO_OPCLASS[m] |
| * QCA_WLAN_VENDOR_ATTR_AFC_OPCLASS_INFO_CHAN_LIST[m] |
| * QCA_WLAN_VENDOR_ATTR_AFC_CHAN_EIRP_INFO_CHAN_NUM[0] |
| * QCA_WLAN_VENDOR_ATTR_AFC_CHAN_EIRP_INFO_EIRP[0] |
| * .... |
| * QCA_WLAN_VENDOR_ATTR_AFC_CHAN_EIRP_INFO_CHAN_NUM[j - 1] |
| * QCA_WLAN_VENDOR_ATTR_AFC_CHAN_EIRP_INFO_EIRP[j - 1] |
| * |
| * The following set of attributes will be used to exchange operating class |
| * information for AFC between the user space and the driver. |
| */ |
| enum qca_wlan_vendor_attr_afc_opclass_info { |
| QCA_WLAN_VENDOR_ATTR_AFC_OPCLASS_INFO_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_AFC_OPCLASS_INFO_OPCLASS = 1, |
| QCA_WLAN_VENDOR_ATTR_AFC_OPCLASS_INFO_CHAN_LIST = 2, |
| |
| QCA_WLAN_VENDOR_ATTR_AFC_OPCLASS_INFO_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_AFC_OPCLASS_INFO_MAX = |
| QCA_WLAN_VENDOR_ATTR_AFC_OPCLASS_INFO_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_afc_event_type: Defines values for AFC event type. |
| * Attribute used by QCA_WLAN_VENDOR_ATTR_AFC_EVENT_TYPE attribute. |
| * |
| * @QCA_WLAN_VENDOR_AFC_EVENT_TYPE_EXPIRY: AFC expiry event sent from the |
| * driver to userspace in order to query the new AFC power values. |
| * |
| * @QCA_WLAN_VENDOR_AFC_EVENT_TYPE_POWER_UPDATE_COMPLETE: Power update |
| * complete event will be sent from the driver to userspace to indicate |
| * processing of the AFC response. |
| * |
| * @QCA_WLAN_VENDOR_AFC_EVENT_TYPE_PAYLOAD_RESET: AFC payload reset event |
| * will be sent from the driver to userspace to indicate last received |
| * AFC response data has been cleared on the AP due to invalid data |
| * in the QCA_NL80211_VENDOR_SUBCMD_AFC_RESPONSE. |
| * |
| * The following enum defines the different event types that will be |
| * used by the driver to help trigger corresponding AFC functionality in user |
| * space. |
| */ |
| enum qca_wlan_vendor_afc_event_type { |
| QCA_WLAN_VENDOR_AFC_EVENT_TYPE_EXPIRY = 0, |
| QCA_WLAN_VENDOR_AFC_EVENT_TYPE_POWER_UPDATE_COMPLETE = 1, |
| QCA_WLAN_VENDOR_AFC_EVENT_TYPE_PAYLOAD_RESET = 2, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_afc_ap_deployment_type: Defines values for AP |
| * deployment type. |
| * Attribute used by QCA_WLAN_VENDOR_ATTR_AFC_EVENT_AP_DEPLOYMENT attribute. |
| * |
| * @QCA_WLAN_VENDOR_AFC_AP_DEPLOYMENT_TYPE_UNKNOWN: Unknown AP deployment. |
| * |
| * @QCA_WLAN_VENDOR_AFC_AP_DEPLOYMENT_TYPE_INDOOR: Indoor AP deployment. |
| * |
| * @QCA_WLAN_VENDOR_AFC_AP_DEPLOYMENT_TYPE_OUTDOOR: Outdoor AP deployment. |
| * |
| * The following enum defines different deployment modes that the AP might |
| * come up in. This information will be essential to retrieve deployment-type |
| * specific SP power values for AFC operation. |
| */ |
| enum qca_wlan_vendor_afc_ap_deployment_type { |
| QCA_WLAN_VENDOR_AFC_AP_DEPLOYMENT_TYPE_UNKNOWN = 0, |
| QCA_WLAN_VENDOR_AFC_AP_DEPLOYMENT_TYPE_INDOOR = 1, |
| QCA_WLAN_VENDOR_AFC_AP_DEPLOYMENT_TYPE_OUTDOOR = 2, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_afc_evt_status_code: Defines values AP will use to |
| * indicate AFC response status. |
| * Enum used by QCA_WLAN_VENDOR_ATTR_AFC_EVENT_STATUS_CODE attribute. |
| * |
| * @QCA_WLAN_VENDOR_AFC_EVT_STATUS_CODE_SUCCESS: Success |
| * |
| * @QCA_WLAN_VENDOR_AFC_EVT_STATUS_CODE_TIMEOUT: Indicates AFC indication |
| * command was not received within the expected time of the AFC expiry event |
| * being triggered. |
| * |
| * @QCA_WLAN_VENDOR_AFC_EVT_STATUS_CODE_PARSING_ERROR: Indicates AFC data |
| * parsing error by the driver. |
| * |
| * @QCA_WLAN_VENDOR_AFC_EVT_STATUS_CODE_LOCAL_ERROR: Indicates any other local |
| * error. |
| * |
| * The following enum defines the status codes that the driver will use to |
| * indicate whether the AFC data is valid or not. |
| */ |
| enum qca_wlan_vendor_afc_evt_status_code { |
| QCA_WLAN_VENDOR_AFC_EVT_STATUS_CODE_SUCCESS = 0, |
| QCA_WLAN_VENDOR_AFC_EVT_STATUS_CODE_TIMEOUT = 1, |
| QCA_WLAN_VENDOR_AFC_EVT_STATUS_CODE_PARSING_ERROR = 2, |
| QCA_WLAN_VENDOR_AFC_EVT_STATUS_CODE_LOCAL_ERROR = 3, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_afc_event: Defines attributes to be used with |
| * vendor event QCA_NL80211_VENDOR_SUBCMD_AFC_EVENT. These attributes will |
| * support sending only a single request to the user space at a time. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_AFC_EVENT_TYPE: Required u8 attribute. |
| * Used with event to notify the type of AFC event received. |
| * Valid values are defined in enum qca_wlan_vendor_afc_event_type. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_AFC_EVENT_AP_DEPLOYMENT: u8 attribute. Required when |
| * QCA_WLAN_VENDOR_ATTR_AFC_EVENT_TYPE is QCA_WLAN_VENDOR_AFC_EVENT_TYPE_EXPIRY, |
| * otherwise unused. |
| * |
| * This attribute is used to indicate the AP deployment type in the AFC request. |
| * Valid values are defined in enum qca_wlan_vendor_afc_ap_deployment_type. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_AFC_EVENT_REQ_ID: Required u32 attribute. |
| * Unique request identifier generated by the AFC client for every |
| * AFC expiry event trigger. See also QCA_WLAN_VENDOR_ATTR_AFC_RESP_REQ_ID. |
| * The user space application is responsible for ensuring no duplicate values |
| * are in-flight with the server, e.g., by delaying a request, should the same |
| * value be received from different radios in parallel. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_AFC_EVENT_AFC_WFA_VERSION: u32 attribute. Optional. |
| * It is used when the QCA_WLAN_VENDOR_ATTR_AFC_EVENT_TYPE is |
| * QCA_WLAN_VENDOR_AFC_EVENT_TYPE_EXPIRY, otherwise unused. |
| * |
| * This attribute indicates the AFC spec version information. This will |
| * indicate the AFC version AFC client must use to query the AFC data. |
| * Bits 15:0 - Minor version |
| * Bits 31:16 - Major version |
| * |
| * @QCA_WLAN_VENDOR_ATTR_AFC_EVENT_MIN_DES_POWER: u16 attribute. Required when |
| * QCA_WLAN_VENDOR_ATTR_AFC_EVENT_TYPE is QCA_WLAN_VENDOR_AFC_EVENT_TYPE_EXPIRY, |
| * otherwise unused. |
| * This attribute indicates the minimum desired power (in dBm) for |
| * the queried spectrum. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_AFC_EVENT_STATUS_CODE: u8 attribute. Required when |
| * QCA_WLAN_VENDOR_ATTR_AFC_EVENT_TYPE is |
| * QCA_WLAN_VENDOR_AFC_EVENT_TYPE_POWER_UPDATE_COMPLETE, otherwise unused. |
| * |
| * Valid values are defined in enum qca_wlan_vendor_afc_evt_status_code. |
| * This attribute is used to indicate if there were any errors parsing the |
| * AFC response. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_AFC_EVENT_SERVER_RESP_CODE: s32 attribute. Required |
| * when QCA_WLAN_VENDOR_ATTR_AFC_EVENT_TYPE is |
| * QCA_WLAN_VENDOR_AFC_EVENT_TYPE_POWER_UPDATE_COMPLETE, otherwise unused. |
| * |
| * This attribute indicates the AFC response code. The AFC response codes are |
| * in the following categories: |
| * -1: General Failure. |
| * 0: Success. |
| * 100 - 199: General errors related to protocol. |
| * 300 - 399: Error events specific to message exchange |
| * for the Available Spectrum Inquiry. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_AFC_EVENT_EXP_DATE: u32 attribute. Required when |
| * QCA_WLAN_VENDOR_ATTR_AFC_EVENT_TYPE is |
| * QCA_WLAN_VENDOR_AFC_EVENT_TYPE_POWER_UPDATE_COMPLETE, otherwise unused. |
| * |
| * This attribute indicates the date until which the current response is |
| * valid for in UTC format. |
| * Date format: bits 7:0 - DD (Day 1-31) |
| * bits 15:8 - MM (Month 1-12) |
| * bits 31:16 - YYYY (Year) |
| * |
| * @QCA_WLAN_VENDOR_ATTR_AFC_EVENT_EXP_TIME: u32 attribute. Required when |
| * QCA_WLAN_VENDOR_ATTR_AFC_EVENT_TYPE is |
| * QCA_WLAN_VENDOR_AFC_EVENT_TYPE_POWER_UPDATE_COMPLETE, otherwise unused. |
| * |
| * This attribute indicates the time until which the current response is |
| * valid for in UTC format. |
| * Time format: bits 7:0 - SS (Seconds 0-59) |
| * bits 15:8 - MM (Minutes 0-59) |
| * bits 23:16 - HH (Hours 0-23) |
| * bits 31:24 - Reserved |
| * |
| * @QCA_WLAN_VENDOR_ATTR_AFC_EVENT_FREQ_RANGE_LIST: Array of nested attributes |
| * for updating the list of frequency ranges to be queried. |
| * Required when QCA_WLAN_VENDOR_ATTR_AFC_EVENT_TYPE is |
| * QCA_WLAN_VENDOR_AFC_EVENT_TYPE_EXPIRY or |
| * QCA_WLAN_VENDOR_AFC_EVENT_TYPE_POWER_UPDATE_COMPLETE, otherwise unused. |
| * It uses the attributes defined in |
| * enum qca_wlan_vendor_attr_afc_freq_psd_info. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_AFC_EVENT_OPCLASS_CHAN_LIST: Array of nested attributes |
| * for updating the list of operating classes and corresponding channels to be |
| * queried. |
| * Required when QCA_WLAN_VENDOR_ATTR_AFC_EVENT_TYPE is |
| * QCA_WLAN_VENDOR_AFC_EVENT_TYPE_EXPIRY or |
| * QCA_WLAN_VENDOR_AFC_EVENT_TYPE_POWER_UPDATE_COMPLETE, otherwise unused. |
| * It uses the attributes defined in enum qca_wlan_vendor_attr_afc_opclass_info. |
| */ |
| enum qca_wlan_vendor_attr_afc_event { |
| QCA_WLAN_VENDOR_ATTR_AFC_EVENT_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_AFC_EVENT_TYPE = 1, |
| QCA_WLAN_VENDOR_ATTR_AFC_EVENT_AP_DEPLOYMENT = 2, |
| QCA_WLAN_VENDOR_ATTR_AFC_EVENT_REQ_ID = 3, |
| QCA_WLAN_VENDOR_ATTR_AFC_EVENT_AFC_WFA_VERSION = 4, |
| QCA_WLAN_VENDOR_ATTR_AFC_EVENT_MIN_DES_POWER = 5, |
| QCA_WLAN_VENDOR_ATTR_AFC_EVENT_STATUS_CODE = 6, |
| QCA_WLAN_VENDOR_ATTR_AFC_EVENT_SERVER_RESP_CODE = 7, |
| QCA_WLAN_VENDOR_ATTR_AFC_EVENT_EXP_DATE = 8, |
| QCA_WLAN_VENDOR_ATTR_AFC_EVENT_EXP_TIME = 9, |
| QCA_WLAN_VENDOR_ATTR_AFC_EVENT_FREQ_RANGE_LIST = 10, |
| QCA_WLAN_VENDOR_ATTR_AFC_EVENT_OPCLASS_CHAN_LIST = 11, |
| |
| QCA_WLAN_VENDOR_ATTR_AFC_EVENT_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_AFC_EVENT_MAX = |
| QCA_WLAN_VENDOR_ATTR_AFC_EVENT_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_afc_response: Defines attributes to be used |
| * with vendor command QCA_NL80211_VENDOR_SUBCMD_AFC_RESPONSE. These attributes |
| * will support sending only a single AFC response to the driver at a time. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_AFC_RESP_DATA: Type is NLA_STRING. Required attribute. |
| * This attribute will be used to send a single Spectrum Inquiry response object |
| * from the 'availableSpectrumInquiryResponses' array object from the response |
| * JSON. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_AFC_RESP_TIME_TO_LIVE: Required u32 attribute. |
| * |
| * This attribute indicates the period (in seconds) for which the response |
| * data received is valid for. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_AFC_RESP_REQ_ID: Required u32 attribute. |
| * |
| * This attribute indicates the request ID for which the corresponding |
| * response is being sent for. See also QCA_WLAN_VENDOR_ATTR_AFC_EVENT_REQ_ID. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_AFC_RESP_EXP_DATE: Required u32 attribute. |
| * |
| * This attribute indicates the date until which the current response is |
| * valid for in UTC format. |
| * Date format: bits 7:0 - DD (Day 1-31) |
| * bits 15:8 - MM (Month 1-12) |
| * bits 31:16 - YYYY (Year) |
| * |
| * @QCA_WLAN_VENDOR_ATTR_AFC_RESP_EXP_TIME: Required u32 attribute. |
| * |
| * This attribute indicates the time until which the current response is |
| * valid for in UTC format. |
| * Time format: bits 7:0 - SS (Seconds 0-59) |
| * bits 15:8 - MM (Minutes 0-59) |
| * bits 23:16 - HH (Hours 0-23) |
| * bits 31:24 - Reserved |
| * |
| * @QCA_WLAN_VENDOR_ATTR_AFC_RESP_AFC_SERVER_RESP_CODE: Required s32 attribute. |
| * |
| * This attribute indicates the AFC response code. The AFC response codes are |
| * in the following categories: |
| * -1: General Failure. |
| * 0: Success. |
| * 100 - 199: General errors related to protocol. |
| * 300 - 399: Error events specific to message exchange |
| * for the Available Spectrum Inquiry. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_AFC_RESP_FREQ_PSD_INFO: Array of nested attributes |
| * for PSD info of all the queried frequency ranges. It uses the attributes |
| * defined in enum qca_wlan_vendor_attr_afc_freq_psd_info. Required attribute. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_AFC_RESP_OPCLASS_CHAN_EIRP_INFO: Array of nested |
| * attributes for EIRP info of all queried operating class/channels. It uses |
| * the attributes defined in enum qca_wlan_vendor_attr_afc_opclass_info and |
| * enum qca_wlan_vendor_attr_afc_chan_eirp_info. Required attribute. |
| * |
| */ |
| enum qca_wlan_vendor_attr_afc_response { |
| QCA_WLAN_VENDOR_ATTR_AFC_RESP_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_AFC_RESP_DATA = 1, |
| QCA_WLAN_VENDOR_ATTR_AFC_RESP_TIME_TO_LIVE = 2, |
| QCA_WLAN_VENDOR_ATTR_AFC_RESP_REQ_ID = 3, |
| QCA_WLAN_VENDOR_ATTR_AFC_RESP_EXP_DATE = 4, |
| QCA_WLAN_VENDOR_ATTR_AFC_RESP_EXP_TIME = 5, |
| QCA_WLAN_VENDOR_ATTR_AFC_RESP_AFC_SERVER_RESP_CODE = 6, |
| QCA_WLAN_VENDOR_ATTR_AFC_RESP_FREQ_PSD_INFO = 7, |
| QCA_WLAN_VENDOR_ATTR_AFC_RESP_OPCLASS_CHAN_EIRP_INFO = 8, |
| |
| QCA_WLAN_VENDOR_ATTR_AFC_RESP_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_AFC_RESP_MAX = |
| QCA_WLAN_VENDOR_ATTR_AFC_RESP_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_dozed_ap_state - Doze states for AP interface |
| * |
| * @QCA_WLAN_DOZED_AP_DISABLE: Disable doze state on the AP interface. |
| * |
| * @QCA_WLAN_DOZED_AP_ENABLE: Enable doze state on the AP interface. AP starts |
| * beaconing at higher beacon interval with Rx disabled. |
| */ |
| enum qca_wlan_dozed_ap_state { |
| QCA_WLAN_DOZED_AP_DISABLE = 0, |
| QCA_WLAN_DOZED_AP_ENABLE = 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_dozed_ap - Used by the vendor command |
| * @QCA_NL80211_VENDOR_SUBCMD_DOZED_AP to configure or receive dozed AP mode |
| * configuration. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_DOZED_AP_STATE: u8 attribute. |
| * Configures the doze state for an AP interface. Possible values are defined |
| * in enum qca_wlan_dozed_ap_state. @QCA_NL80211_VENDOR_SUBCMD_DOZED_AP event |
| * gets triggered asynchronously to provide updated AP interface configuration. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_DOZED_AP_COOKIE: Unsigned 64-bit cookie provided by |
| * the driver in the response to specific @QCA_NL80211_VENDOR_SUBCMD_DOZED_AP |
| * command, which is used later to maintain synchronization between commands |
| * and asynchronous events. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_DOZED_AP_NEXT_TSF: u64 attribute. |
| * Used in event to indicate the next TBTT TSF timer value after applying the |
| * doze mode configuration. Next TBTT TSF is the time at which the AP sends |
| * the first beacon after entering or exiting dozed mode. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_DOZED_AP_BI_MULTIPLIER: u16 attribute. |
| * Used with event to inform the periodicity of beacon transmission that would |
| * be skipped at all TBTTs in between. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_DOZED_AP_PAD: Attribute used for padding for 64-bit |
| * alignment. |
| */ |
| enum qca_wlan_vendor_attr_dozed_ap { |
| QCA_WLAN_VENDOR_ATTR_DOZED_AP_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_DOZED_AP_STATE = 1, |
| QCA_WLAN_VENDOR_ATTR_DOZED_AP_COOKIE = 2, |
| QCA_WLAN_VENDOR_ATTR_DOZED_AP_NEXT_TSF = 3, |
| QCA_WLAN_VENDOR_ATTR_DOZED_AP_BI_MULTIPLIER = 4, |
| QCA_WLAN_VENDOR_ATTR_DOZED_AP_PAD = 5, |
| |
| /* Keep last */ |
| QCA_WLAN_VENDOR_ATTR_DOZED_AP_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_DOZED_AP_MAX = |
| QCA_WLAN_VENDOR_ATTR_DOZED_AP_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_monitor_mode_status - Represents the status codes |
| * used with QCA_NL80211_VENDOR_SUBCMD_GET_MONITOR_MODE. |
| * @QCA_WLAN_VENDOR_MONITOR_MODE_NO_CAPTURE_RUNNING: Used to indicate no |
| * capture running status. |
| * @QCA_WLAN_VENDOR_MONITOR_MODE_CAPTURE_RUNNING: Used to indicate |
| * capture running status. |
| **/ |
| |
| enum qca_wlan_vendor_monitor_mode_status { |
| QCA_WLAN_VENDOR_MONITOR_MODE_NO_CAPTURE_RUNNING = 0, |
| QCA_WLAN_VENDOR_MONITOR_MODE_CAPTURE_RUNNING = 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_get_monitor_mode - Used by the |
| * vendor command QCA_NL80211_VENDOR_SUBCMD_GET_MONITOR_MODE to report |
| * information regarding the local packet capture over the monitor mode. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_MONITOR_MODE_STATUS: u32 attribute. This attribute |
| * represents the status of the start capture commands. The values used with |
| * this attribute are defined in enum qca_wlan_vendor_monitor_mode_status. This |
| * is returned by the driver in the response to the command. |
| */ |
| |
| enum qca_wlan_vendor_attr_get_monitor_mode { |
| QCA_WLAN_VENDOR_ATTR_GET_MONITOR_MODE_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_GET_MONITOR_MODE_STATUS = 1, |
| |
| /* Keep last */ |
| QCA_WLAN_VENDOR_ATTR_GET_MONITOR_MODE_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_GET_MONITOR_MODE_MAX = |
| QCA_WLAN_VENDOR_ATTR_GET_MONITOR_MODE_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_link_state_op_types - Defines different types of |
| * operations for which %QCA_NL80211_VENDOR_SUBCMD_MLO_LINK_STATE can be used. |
| * Will be used with %QCA_WLAN_VENDOR_ATTR_LINK_STATE_OP_TYPE attribute. |
| * |
| * @QCA_WLAN_VENDOR_LINK_STATE_OP_GET - Get the MLO links state information. |
| * @QCA_WLAN_VENDOR_LINK_STATE_OP_SET - Set the MLO links state information. |
| */ |
| enum qca_wlan_vendor_link_state_op_types { |
| QCA_WLAN_VENDOR_LINK_STATE_OP_GET = 0, |
| QCA_WLAN_VENDOR_LINK_STATE_OP_SET = 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_link_state_control_modes - Represents the types of MLO |
| * links state control modes. This enum is used by |
| * %QCA_WLAN_VENDOR_ATTR_LINK_STATE_CONTROL_MODE attribute. |
| * |
| * @QCA_WLAN_VENDOR_LINK_STATE_CONTROL_MODE_DEFAULT: MLO links state controlled |
| * by the driver. |
| * @QCA_WLAN_VENDOR_LINK_STATE_CONTROL_MODE_USER: MLO links state controlled by |
| * user space. |
| * @QCA_WLAN_VENDOR_LINK_STATE_CONTROL_MODE_MIXED: User space provides the |
| * desired number of MLO links to operate in active state at any given time. |
| * The driver will choose which MLO links should operate in the active state. |
| * See enum qca_wlan_vendor_link_state for active state definition. |
| */ |
| enum qca_wlan_vendor_link_state_control_modes { |
| QCA_WLAN_VENDOR_LINK_STATE_CONTROL_MODE_DEFAULT = 0, |
| QCA_WLAN_VENDOR_LINK_STATE_CONTROL_MODE_USER = 1, |
| QCA_WLAN_VENDOR_LINK_STATE_CONTROL_MODE_MIXED = 2, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_link_state_operation_modes - Represents the types of MLO |
| * links state operation modes. This enum is used by |
| * %QCA_WLAN_VENDOR_ATTR_LINK_STATE_OPERATION_MODE attribute. |
| * |
| * @QCA_WLAN_VENDOR_LINK_STATE_OPERATION_MODE_DEFAULT: In the default operation |
| * mode, the driver selects the operating mode of the links, without any |
| * guidance from the user space. |
| * @QCA_WLAN_VENDOR_LINK_STATE_OPERATION_MODE_LOW_LATENCY: In the low latency |
| * operation mode the driver should select MLO links that will achieve low |
| * latency. |
| * @QCA_WLAN_VENDOR_LINK_STATE_OPERATION_MODE_HIGH_THROUGHPUT: In the high |
| * throughput operation mode the driver should select MLO links that will |
| * achieve higher throughput. |
| * @QCA_WLAN_VENDOR_LINK_STATE_OPERATION_MODE_LOW_POWER: In the low power |
| * operation mode the driver should select MLO links that will achieve low |
| * power. |
| */ |
| enum qca_wlan_vendor_link_state_operation_modes { |
| QCA_WLAN_VENDOR_LINK_STATE_OPERATION_MODE_DEFAULT = 0, |
| QCA_WLAN_VENDOR_LINK_STATE_OPERATION_MODE_LOW_LATENCY = 1, |
| QCA_WLAN_VENDOR_LINK_STATE_OPERATION_MODE_HIGH_THROUGHPUT = 2, |
| QCA_WLAN_VENDOR_LINK_STATE_OPERATION_MODE_LOW_POWER = 3, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_link_state - Represents the possible link states of an |
| * MLO link. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_LINK_STATE_INACTIVE: In this state, the link will not |
| * be used for data transmission but it can have TIDs mapped to it. It will be |
| * in doze state always and does not monitor the beacons. |
| * @QCA_WLAN_VENDOR_ATTR_LINK_STATE_ACTIVE: In this state, the link will be |
| * used for data TX/RX and monitors the beacons to check TIM bit indication. |
| * It may enter doze state and comes out based on the transmit data traffic and |
| * TIM bit indication in the beacon. |
| */ |
| enum qca_wlan_vendor_link_state { |
| QCA_WLAN_VENDOR_LINK_STATE_INACTIVE = 0, |
| QCA_WLAN_VENDOR_LINK_STATE_ACTIVE = 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_link_state_config - Definition of attributes used |
| * inside nested attribute %QCA_WLAN_VENDOR_ATTR_LINK_STATE_CONFIG. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_LINK_STATE_CONFIG_LINK_ID: u8 attribute, link ID of the |
| * MLO link. |
| * @QCA_WLAN_VENDOR_ATTR_LINK_STATE_CONFIG_STATE: u32 attribute. See |
| * enum qca_wlan_vendor_link_state for possible MLO link states. |
| */ |
| |
| enum qca_wlan_vendor_attr_link_state_config { |
| QCA_WLAN_VENDOR_ATTR_LINK_STATE_CONFIG_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_LINK_STATE_CONFIG_LINK_ID = 1, |
| QCA_WLAN_VENDOR_ATTR_LINK_STATE_CONFIG_STATE = 2, |
| |
| /* Keep last */ |
| QCA_WLAN_VENDOR_ATTR_LINK_STATE_CONFIG_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_LINK_STATE_CONFIG_MAX = |
| QCA_WLAN_VENDOR_ATTR_LINK_STATE_CONFIG_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_mlo_link_state - Attributes used by |
| * %QCA_NL80211_VENDOR_SUBCMD_MLO_LINK_STATE vendor command. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_LINK_STATE_OP_TYPE: u32 attribute. Indicates the type |
| * of the operation %QCA_NL80211_VENDOR_SUBCMD_MLO_LINK_STATE intended for. |
| * Required only in a command. Possible values for this attribute are defined in |
| * enum qca_wlan_vendor_link_state_op_types. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_LINK_STATE_CONTROL_MODE: u32 attribute. Indicates MLO |
| * links control mode type. Optional attribute in a command when |
| * %QCA_WLAN_VENDOR_ATTR_LINK_STATE_OP_TYPE is set to |
| * %QCA_WLAN_VENDOR_LINK_STATE_OP_SET. Required attribute in a response when |
| * %QCA_WLAN_VENDOR_ATTR_LINK_STATE_OP_TYPE is set to |
| * %QCA_WLAN_VENDOR_LINK_STATE_OP_GET. |
| * See enum qca_wlan_vendor_link_state_control_modes for possible control modes. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_LINK_STATE_CONFIG: Array of nested attributes. |
| * Indicates the state of the each MLO link affiliated with the interface. |
| * Required attribute in a command when %QCA_WLAN_VENDOR_ATTR_LINK_STATE_OP_TYPE |
| * is set to %QCA_WLAN_VENDOR_LINK_STATE_OP_SET and |
| * %QCA_WLAN_VENDOR_ATTR_LINK_STATE_CONTROL_MODE is set to |
| * %QCA_WLAN_VENDOR_LINK_STATE_CONTROL_MODE_USER. Required attribute in a |
| * response when %QCA_WLAN_VENDOR_ATTR_LINK_STATE_OP_TYPE is set to |
| * %QCA_WLAN_VENDOR_LINK_STATE_OP_GET. |
| * See enum qca_wlan_vendor_attr_link_state_config for the nested attributes. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_LINK_STATE_MIXED_MODE_ACTIVE_NUM_LINKS: u8 attribute. |
| * Represents the number of active state links. See enum |
| * qca_wlan_vendor_link_state for active state definition. |
| * Required attribute in a command when %QCA_WLAN_VENDOR_ATTR_LINK_STATE_OP_TYPE |
| * is set to %QCA_WLAN_VENDOR_LINK_STATE_OP_SET and |
| * %QCA_WLAN_VENDOR_ATTR_LINK_STATE_CONTROL_MODE is set to |
| * %QCA_WLAN_VENDOR_LINK_STATE_CONTROL_MODE_MIXED. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_LINK_STATE_OPERATION_MODE: u32 attribute. Indicates MLO |
| * links operation mode type. Optional attribute in a command when |
| * %QCA_WLAN_VENDOR_ATTR_LINK_STATE_OP_TYPE is set to |
| * %QCA_WLAN_VENDOR_LINK_STATE_OP_SET. Required attribute in a response when |
| * %QCA_WLAN_VENDOR_ATTR_LINK_STATE_OP_TYPE is set to |
| * %QCA_WLAN_VENDOR_LINK_STATE_OP_GET. |
| * See enum qca_wlan_vendor_link_state_operation_modes for possible operation |
| * modes. |
| */ |
| enum qca_wlan_vendor_attr_mlo_link_state { |
| QCA_WLAN_VENDOR_ATTR_LINK_STATE_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_LINK_STATE_OP_TYPE = 1, |
| QCA_WLAN_VENDOR_ATTR_LINK_STATE_CONTROL_MODE = 2, |
| QCA_WLAN_VENDOR_ATTR_LINK_STATE_CONFIG = 3, |
| QCA_WLAN_VENDOR_ATTR_LINK_STATE_MIXED_MODE_ACTIVE_NUM_LINKS = 4, |
| QCA_WLAN_VENDOR_ATTR_LINK_STATE_OPERATION_MODE = 5, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_LINK_STATE_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_LINK_STATE_MAX = |
| QCA_WLAN_VENDOR_ATTR_LINK_STATE_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_tid_link_map_status - Definition of attributes used |
| * inside nested attribute %QCA_WLAN_VENDOR_ATTR_TID_TO_LINK_MAP_STATUS. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_LINK_TID_MAP_STATUS_UPLINK: Required u16 attribute |
| * within nested attribute %QCA_WLAN_VENDOR_ATTR_TID_TO_LINK_MAP_STATUS. |
| * Indicates the link mapping bitmap of a TID for uplink traffic. It is a |
| * bitmask of the link IDs in which a bit set means that the TID is mapped with |
| * that link ID in uplink traffic. Otherwise, the TID is not mapped to uplink |
| * traffic for that link. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_LINK_TID_MAP_STATUS_DOWNLINK: Required u16 attribute |
| * within nested attribute %QCA_WLAN_VENDOR_ATTR_TID_TO_LINK_MAP_STATUS. |
| * Indicates the link mapping bitmap of a TID for downlink traffic. It is a |
| * bitmask of the link IDs in which a bit set means that the TID is mapped with |
| * that link ID in downlink traffic. Otherwise, the TID is not mapped to |
| * downlink traffic for that link. |
| */ |
| enum qca_wlan_vendor_attr_tid_link_map_status { |
| QCA_WLAN_VENDOR_ATTR_LINK_TID_MAP_STATUS_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_LINK_TID_MAP_STATUS_UPLINK = 1, |
| QCA_WLAN_VENDOR_ATTR_LINK_TID_MAP_STATUS_DOWNLINK = 2, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_LINK_TID_MAP_STATUS_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_LINK_TID_MAP_STATUS_MAX = |
| QCA_WLAN_VENDOR_ATTR_LINK_TID_MAP_STATUS_AFTER_LAST - 1, |
| }; |
| |
| /* |
| * enum qca_wlan_vendor_attr_tid_to_link_map: Definition of attributes used with |
| * %QCA_NL80211_VENDOR_SUBCMD_TID_TO_LINK_MAP event. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TID_TO_LINK_MAP_AP_MLD_ADDR: Required attribute. 6-byte |
| * AP MLD address with which this TID-to-link negotiation mapping is |
| * established/updated. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TID_TO_LINK_MAP_STATUS: Optional attribute. Array of |
| * nested attributes containing TID-to-links mapping information. This will have |
| * TID-to-link mapping for TID0 to TID7, each containing the uplink and downlink |
| * map information. If this attribute is not present the default TID-to-link |
| * mapping is in use, i.e., all TIDs are mapped to all links for both uplink and |
| * downlink traffic. |
| * See enum qca_wlan_vendor_attr_tid_link_map_status for the nested attributes. |
| */ |
| enum qca_wlan_vendor_attr_tid_to_link_map { |
| QCA_WLAN_VENDOR_ATTR_TID_TO_LINK_MAP_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_TID_TO_LINK_MAP_AP_MLD_ADDR = 1, |
| QCA_WLAN_VENDOR_ATTR_TID_TO_LINK_MAP_STATUS = 2, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_TID_TO_LINK_MAP_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_TID_TO_LINK_MAP_MAX = |
| QCA_WLAN_VENDOR_ATTR_TID_TO_LINK_MAP_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_link_reconfig: Definition of attributes used |
| * with %QCA_NL80211_VENDOR_SUBCMD_LINK_RECONFIG event. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_LINK_RECONFIG_AP_MLD_ADDR: Required attribute. |
| * 6-byte AP MLD address of the AP which indicated the link reconfiguration. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_LINK_RECONFIG_REMOVED_LINKS: Required u16 attribute. |
| * A bitmap of the removed setup links link IDs. |
| */ |
| enum qca_wlan_vendor_attr_link_reconfig { |
| |
| QCA_WLAN_VENDOR_ATTR_LINK_RECONFIG_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_LINK_RECONFIG_AP_MLD_ADDR = 1, |
| QCA_WLAN_VENDOR_ATTR_LINK_RECONFIG_REMOVED_LINKS = 2, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_LINK_RECONFIG_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_LINK_RECONFIG_MAX = |
| QCA_WLAN_VENDOR_ATTR_LINK_RECONFIG_AFTER_LAST - 1 |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_tdls_disc_rsp_ext - Attributes used by |
| * %QCA_NL80211_VENDOR_SUBCMD_TDLS_DISC_RSP_EXT vendor command. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TDLS_DISC_RSP_EXT_TX_LINK: u8 attribute. |
| * Indicates the MLO link id on which the TDLS discovery response |
| * frame is to be transmitted. |
| */ |
| enum qca_wlan_vendor_attr_tdls_disc_rsp_ext { |
| QCA_WLAN_VENDOR_ATTR_TDLS_DISC_RSP_EXT_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_TDLS_DISC_RSP_EXT_TX_LINK = 1, |
| |
| /* Keep last */ |
| QCA_WLAN_VENDOR_ATTR_TDLS_DISC_RSP_EXT_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_TDLS_DISC_RSP_EXT_MAX = |
| QCA_WLAN_VENDOR_ATTR_TDLS_DISC_RSP_EXT_AFTER_LAST - 1, |
| }; |
| |
| #endif /* QCA_VENDOR_H */ |