| /include/ "skeleton.dtsi" |
| #include <dt-bindings/input/input.h> |
| #include <dt-bindings/gpio/gpio.h> |
| |
| #define MBUS_ID(target,attributes) (((target) << 24) | ((attributes) << 16)) |
| |
| / { |
| compatible = "marvell,kirkwood"; |
| interrupt-parent = <&intc>; |
| |
| cpus { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| cpu@0 { |
| device_type = "cpu"; |
| compatible = "marvell,feroceon"; |
| reg = <0>; |
| clocks = <&core_clk 1>, <&core_clk 3>, <&gate_clk 11>; |
| clock-names = "cpu_clk", "ddrclk", "powersave"; |
| }; |
| }; |
| |
| aliases { |
| gpio0 = &gpio0; |
| gpio1 = &gpio1; |
| i2c0 = &i2c0; |
| }; |
| |
| mbus { |
| compatible = "marvell,kirkwood-mbus", "simple-bus"; |
| #address-cells = <2>; |
| #size-cells = <1>; |
| /* If a board file needs to change this ranges it must replace it completely */ |
| ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000 /* internal-regs */ |
| MBUS_ID(0x01, 0x2f) 0 0xf4000000 0x10000 /* nand flash */ |
| MBUS_ID(0x03, 0x01) 0 0xf5000000 0x10000 /* crypto sram */ |
| >; |
| controller = <&mbusc>; |
| pcie-mem-aperture = <0xe0000000 0x10000000>; /* 256 MiB memory space */ |
| pcie-io-aperture = <0xf2000000 0x100000>; /* 1 MiB I/O space */ |
| |
| nand: nand@012f { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| cle = <0>; |
| ale = <1>; |
| bank-width = <1>; |
| compatible = "marvell,orion-nand"; |
| reg = <MBUS_ID(0x01, 0x2f) 0 0x400>; |
| chip-delay = <25>; |
| /* set partition map and/or chip-delay in board dts */ |
| clocks = <&gate_clk 7>; |
| pinctrl-0 = <&pmx_nand>; |
| pinctrl-names = "default"; |
| status = "disabled"; |
| }; |
| |
| crypto_sram: sa-sram@0301 { |
| compatible = "mmio-sram"; |
| reg = <MBUS_ID(0x03, 0x01) 0x0 0x800>; |
| clocks = <&gate_clk 17>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| }; |
| }; |
| |
| ocp@f1000000 { |
| compatible = "simple-bus"; |
| ranges = <0x00000000 0xf1000000 0x0100000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| pinctrl: pin-controller@10000 { |
| /* set compatible property in SoC file */ |
| reg = <0x10000 0x20>; |
| |
| pmx_ge1: pmx-ge1 { |
| marvell,pins = "mpp20", "mpp21", "mpp22", "mpp23", |
| "mpp24", "mpp25", "mpp26", "mpp27", |
| "mpp30", "mpp31", "mpp32", "mpp33"; |
| marvell,function = "ge1"; |
| }; |
| |
| pmx_nand: pmx-nand { |
| marvell,pins = "mpp0", "mpp1", "mpp2", "mpp3", |
| "mpp4", "mpp5", "mpp18", "mpp19"; |
| marvell,function = "nand"; |
| }; |
| |
| /* |
| * Default SPI0 pinctrl setting with CSn on mpp0, |
| * overwrite marvell,pins on board level if required. |
| */ |
| pmx_spi: pmx-spi { |
| marvell,pins = "mpp0", "mpp1", "mpp2", "mpp3"; |
| marvell,function = "spi"; |
| }; |
| |
| pmx_twsi0: pmx-twsi0 { |
| marvell,pins = "mpp8", "mpp9"; |
| marvell,function = "twsi0"; |
| }; |
| |
| /* |
| * Default UART pinctrl setting without RTS/CTS, |
| * overwrite marvell,pins on board level if required. |
| */ |
| pmx_uart0: pmx-uart0 { |
| marvell,pins = "mpp10", "mpp11"; |
| marvell,function = "uart0"; |
| }; |
| |
| pmx_uart1: pmx-uart1 { |
| marvell,pins = "mpp13", "mpp14"; |
| marvell,function = "uart1"; |
| }; |
| }; |
| |
| core_clk: core-clocks@10030 { |
| compatible = "marvell,kirkwood-core-clock"; |
| reg = <0x10030 0x4>; |
| #clock-cells = <1>; |
| }; |
| |
| spi0: spi@10600 { |
| compatible = "marvell,orion-spi"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| cell-index = <0>; |
| interrupts = <23>; |
| reg = <0x10600 0x28>; |
| clocks = <&gate_clk 7>; |
| pinctrl-0 = <&pmx_spi>; |
| pinctrl-names = "default"; |
| status = "disabled"; |
| }; |
| |
| gpio0: gpio@10100 { |
| compatible = "marvell,orion-gpio"; |
| #gpio-cells = <2>; |
| gpio-controller; |
| reg = <0x10100 0x40>; |
| ngpios = <32>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| interrupts = <35>, <36>, <37>, <38>; |
| clocks = <&gate_clk 7>; |
| }; |
| |
| gpio1: gpio@10140 { |
| compatible = "marvell,orion-gpio"; |
| #gpio-cells = <2>; |
| gpio-controller; |
| reg = <0x10140 0x40>; |
| ngpios = <18>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| interrupts = <39>, <40>, <41>; |
| clocks = <&gate_clk 7>; |
| }; |
| |
| i2c0: i2c@11000 { |
| compatible = "marvell,mv64xxx-i2c"; |
| reg = <0x11000 0x20>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| interrupts = <29>; |
| clock-frequency = <100000>; |
| clocks = <&gate_clk 7>; |
| pinctrl-0 = <&pmx_twsi0>; |
| pinctrl-names = "default"; |
| status = "disabled"; |
| }; |
| |
| uart0: serial@12000 { |
| compatible = "ns16550a"; |
| reg = <0x12000 0x100>; |
| reg-shift = <2>; |
| interrupts = <33>; |
| clocks = <&gate_clk 7>; |
| pinctrl-0 = <&pmx_uart0>; |
| pinctrl-names = "default"; |
| status = "disabled"; |
| }; |
| |
| uart1: serial@12100 { |
| compatible = "ns16550a"; |
| reg = <0x12100 0x100>; |
| reg-shift = <2>; |
| interrupts = <34>; |
| clocks = <&gate_clk 7>; |
| pinctrl-0 = <&pmx_uart1>; |
| pinctrl-names = "default"; |
| status = "disabled"; |
| }; |
| |
| mbusc: mbus-controller@20000 { |
| compatible = "marvell,mbus-controller"; |
| reg = <0x20000 0x80>, <0x1500 0x20>; |
| }; |
| |
| sysc: system-controller@20000 { |
| compatible = "marvell,orion-system-controller"; |
| reg = <0x20000 0x120>; |
| }; |
| |
| bridge_intc: bridge-interrupt-ctrl@20110 { |
| compatible = "marvell,orion-bridge-intc"; |
| interrupt-controller; |
| #interrupt-cells = <1>; |
| reg = <0x20110 0x8>; |
| interrupts = <1>; |
| marvell,#interrupts = <6>; |
| }; |
| |
| gate_clk: clock-gating-control@2011c { |
| compatible = "marvell,kirkwood-gating-clock"; |
| reg = <0x2011c 0x4>; |
| clocks = <&core_clk 0>; |
| #clock-cells = <1>; |
| }; |
| |
| l2: l2-cache@20128 { |
| compatible = "marvell,kirkwood-cache"; |
| reg = <0x20128 0x4>; |
| }; |
| |
| intc: main-interrupt-ctrl@20200 { |
| compatible = "marvell,orion-intc"; |
| interrupt-controller; |
| #interrupt-cells = <1>; |
| reg = <0x20200 0x10>, <0x20210 0x10>; |
| }; |
| |
| timer: timer@20300 { |
| compatible = "marvell,orion-timer"; |
| reg = <0x20300 0x20>; |
| interrupt-parent = <&bridge_intc>; |
| interrupts = <1>, <2>; |
| clocks = <&core_clk 0>; |
| }; |
| |
| wdt: watchdog-timer@20300 { |
| compatible = "marvell,orion-wdt"; |
| reg = <0x20300 0x28>, <0x20108 0x4>; |
| interrupt-parent = <&bridge_intc>; |
| interrupts = <3>; |
| clocks = <&gate_clk 7>; |
| status = "okay"; |
| }; |
| |
| cesa: crypto@30000 { |
| compatible = "marvell,kirkwood-crypto"; |
| reg = <0x30000 0x10000>; |
| reg-names = "regs"; |
| interrupts = <22>; |
| clocks = <&gate_clk 17>; |
| marvell,crypto-srams = <&crypto_sram>; |
| marvell,crypto-sram-size = <0x800>; |
| status = "okay"; |
| }; |
| |
| usb0: ehci@50000 { |
| compatible = "marvell,orion-ehci"; |
| reg = <0x50000 0x1000>; |
| interrupts = <19>; |
| clocks = <&gate_clk 3>; |
| status = "okay"; |
| }; |
| |
| dma0: xor@60800 { |
| compatible = "marvell,orion-xor"; |
| reg = <0x60800 0x100 |
| 0x60A00 0x100>; |
| status = "okay"; |
| clocks = <&gate_clk 8>; |
| |
| xor00 { |
| interrupts = <5>; |
| dmacap,memcpy; |
| dmacap,xor; |
| }; |
| xor01 { |
| interrupts = <6>; |
| dmacap,memcpy; |
| dmacap,xor; |
| dmacap,memset; |
| }; |
| }; |
| |
| dma1: xor@60900 { |
| compatible = "marvell,orion-xor"; |
| reg = <0x60900 0x100 |
| 0x60B00 0x100>; |
| status = "okay"; |
| clocks = <&gate_clk 16>; |
| |
| xor00 { |
| interrupts = <7>; |
| dmacap,memcpy; |
| dmacap,xor; |
| }; |
| xor01 { |
| interrupts = <8>; |
| dmacap,memcpy; |
| dmacap,xor; |
| dmacap,memset; |
| }; |
| }; |
| |
| eth0: ethernet-controller@72000 { |
| compatible = "marvell,kirkwood-eth"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x72000 0x4000>; |
| clocks = <&gate_clk 0>; |
| marvell,tx-checksum-limit = <1600>; |
| status = "disabled"; |
| |
| eth0port: ethernet0-port@0 { |
| compatible = "marvell,kirkwood-eth-port"; |
| reg = <0>; |
| interrupts = <11>; |
| /* overwrite MAC address in bootloader */ |
| local-mac-address = [00 00 00 00 00 00]; |
| /* set phy-handle property in board file */ |
| }; |
| }; |
| |
| mdio: mdio-bus@72004 { |
| compatible = "marvell,orion-mdio"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x72004 0x84>; |
| interrupts = <46>; |
| clocks = <&gate_clk 0>; |
| status = "disabled"; |
| |
| /* add phy nodes in board file */ |
| }; |
| |
| eth1: ethernet-controller@76000 { |
| compatible = "marvell,kirkwood-eth"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x76000 0x4000>; |
| clocks = <&gate_clk 19>; |
| marvell,tx-checksum-limit = <1600>; |
| pinctrl-0 = <&pmx_ge1>; |
| pinctrl-names = "default"; |
| status = "disabled"; |
| |
| eth1port: ethernet1-port@0 { |
| compatible = "marvell,kirkwood-eth-port"; |
| reg = <0>; |
| interrupts = <15>; |
| /* overwrite MAC address in bootloader */ |
| local-mac-address = [00 00 00 00 00 00]; |
| /* set phy-handle property in board file */ |
| }; |
| }; |
| |
| sata_phy0: sata-phy@82000 { |
| compatible = "marvell,mvebu-sata-phy"; |
| reg = <0x82000 0x0334>; |
| clocks = <&gate_clk 14>; |
| clock-names = "sata"; |
| #phy-cells = <0>; |
| status = "ok"; |
| }; |
| |
| sata_phy1: sata-phy@84000 { |
| compatible = "marvell,mvebu-sata-phy"; |
| reg = <0x84000 0x0334>; |
| clocks = <&gate_clk 15>; |
| clock-names = "sata"; |
| #phy-cells = <0>; |
| status = "ok"; |
| }; |
| |
| audio0: audio-controller@a0000 { |
| compatible = "marvell,kirkwood-audio"; |
| #sound-dai-cells = <0>; |
| reg = <0xa0000 0x2210>; |
| interrupts = <24>; |
| clocks = <&gate_clk 9>; |
| clock-names = "internal"; |
| status = "disabled"; |
| }; |
| }; |
| }; |