blob: eaa1fc1bc5f54dee8cf61b9fae011a9207630c2f [file] [log] [blame]
/*
* TI DA850/OMAP-L138 EVM board
*
* Copyright (C) 2009 Texas Instruments Incorporated - http://www.ti.com/
*
* Derived from: arch/arm/mach-davinci/board-da830-evm.c
* Original Copyrights follow:
*
* 2007, 2009 (c) MontaVista Software, Inc. This file is licensed under
* the terms of the GNU General Public License version 2. This program
* is licensed "as is" without any warranty of any kind, whether express
* or implied.
*/
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/init.h>
#include <linux/console.h>
#include <linux/i2c.h>
#include <linux/i2c/at24.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <mach/common.h>
#include <mach/irqs.h>
#include <mach/cp_intc.h>
#include <mach/da8xx.h>
static struct davinci_i2c_platform_data da850_evm_i2c_0_pdata = {
.bus_freq = 100, /* kHz */
.bus_delay = 0, /* usec */
};
static struct davinci_uart_config da850_evm_uart_config __initdata = {
.enabled_uarts = 0x7,
};
static __init void da850_evm_init(void)
{
int ret;
ret = da8xx_register_edma();
if (ret)
pr_warning("da850_evm_init: edma registration failed: %d\n",
ret);
ret = da8xx_pinmux_setup(da850_i2c0_pins);
if (ret)
pr_warning("da850_evm_init: i2c0 mux setup failed: %d\n",
ret);
ret = da8xx_register_i2c(0, &da850_evm_i2c_0_pdata);
if (ret)
pr_warning("da850_evm_init: i2c0 registration failed: %d\n",
ret);
ret = da8xx_register_watchdog();
if (ret)
pr_warning("da830_evm_init: watchdog registration failed: %d\n",
ret);
davinci_serial_init(&da850_evm_uart_config);
/*
* shut down uart 0 and 1; they are not used on the board and
* accessing them causes endless "too much work in irq53" messages
* with arago fs
*/
__raw_writel(0, IO_ADDRESS(DA8XX_UART1_BASE) + 0x30);
__raw_writel(0, IO_ADDRESS(DA8XX_UART0_BASE) + 0x30);
}
#ifdef CONFIG_SERIAL_8250_CONSOLE
static int __init da850_evm_console_init(void)
{
return add_preferred_console("ttyS", 2, "115200");
}
console_initcall(da850_evm_console_init);
#endif
static __init void da850_evm_irq_init(void)
{
struct davinci_soc_info *soc_info = &davinci_soc_info;
cp_intc_init((void __iomem *)DA8XX_CP_INTC_VIRT, DA850_N_CP_INTC_IRQ,
soc_info->intc_irq_prios);
}
static void __init da850_evm_map_io(void)
{
da850_init();
}
MACHINE_START(DAVINCI_DA850_EVM, "DaVinci DA850/OMAP-L138 EVM")
.phys_io = IO_PHYS,
.io_pg_offst = (__IO_ADDRESS(IO_PHYS) >> 18) & 0xfffc,
.boot_params = (DA8XX_DDR_BASE + 0x100),
.map_io = da850_evm_map_io,
.init_irq = da850_evm_irq_init,
.timer = &davinci_timer,
.init_machine = da850_evm_init,
MACHINE_END