Mauro Carvalho Chehab | 447d6fb | 2006-05-22 10:31:37 -0300 | [diff] [blame] | 1 | The controls for the mux are GPIO [0,1] for source, and GPIO 2 for muting. |
| 2 | |
| 3 | GPIO0 GPIO1 |
| 4 | 0 0 TV Audio |
| 5 | 1 0 FM radio |
| 6 | 0 1 Line-In |
| 7 | 1 1 Mono tuner bypass or CD passthru (tuner specific) |
| 8 | |
| 9 | GPIO 16(i believe) is tied to the IR port (if present). |
| 10 | |
| 11 | ------------------------------------------------------------------------------------ |
| 12 | |
| 13 | >From the data sheet: |
| 14 | Register 24'h20004 PCI Interrupt Status |
| 15 | bit [18] IR_SMP_INT Set when 32 input samples have been collected over |
| 16 | gpio[16] pin into GP_SAMPLE register. |
| 17 | |
| 18 | What's missing from the data sheet: |
| 19 | |
| 20 | Setup 4KHz sampling rate (roughly 2x oversampled; good enough for our RC5 |
| 21 | compat remote) |
| 22 | set register 0x35C050 to 0xa80a80 |
| 23 | |
| 24 | enable sampling |
| 25 | set register 0x35C054 to 0x5 |
| 26 | |
| 27 | Of course, enable the IRQ bit 18 in the interrupt mask register .(and |
| 28 | provide for a handler) |
| 29 | |
| 30 | GP_SAMPLE register is at 0x35C058 |
| 31 | |
| 32 | Bits are then right shifted into the GP_SAMPLE register at the specified |
Matt LaPlante | d6bc8ac | 2006-10-03 22:54:15 +0200 | [diff] [blame] | 33 | rate; you get an interrupt when a full DWORD is received. |
Mauro Carvalho Chehab | 447d6fb | 2006-05-22 10:31:37 -0300 | [diff] [blame] | 34 | You need to recover the actual RC5 bits out of the (oversampled) IR sensor |
| 35 | bits. (Hint: look for the 0/1and 1/0 crossings of the RC5 bi-phase data) An |
| 36 | actual raw RC5 code will span 2-3 DWORDS, depending on the actual alignment. |
| 37 | |
| 38 | I'm pretty sure when no IR signal is present the receiver is always in a |
| 39 | marking state(1); but stray light, etc can cause intermittent noise values |
| 40 | as well. Remember, this is a free running sample of the IR receiver state |
| 41 | over time, so don't assume any sample starts at any particular place. |
| 42 | |
| 43 | http://www.atmel.com/dyn/resources/prod_documents/doc2817.pdf |
| 44 | This data sheet (google search) seems to have a lovely description of the |
| 45 | RC5 basics |
| 46 | |
Justin P. Mattock | 0ea6e61 | 2010-07-23 20:51:24 -0700 | [diff] [blame] | 47 | http://www.nenya.be/beor/electronics/rc5.htm and more data |
Mauro Carvalho Chehab | 447d6fb | 2006-05-22 10:31:37 -0300 | [diff] [blame] | 48 | |
| 49 | http://www.ee.washington.edu/circuit_archive/text/ir_decode.txt |
| 50 | and even a reference to how to decode a bi-phase data stream. |
| 51 | |
| 52 | http://www.xs4all.nl/~sbp/knowledge/ir/rc5.htm |
| 53 | still more info |
| 54 | |