| #define EM_GPIO_0 (1 << 0) |
| #define EM_GPIO_1 (1 << 1) |
| #define EM_GPIO_2 (1 << 2) |
| #define EM_GPIO_3 (1 << 3) |
| #define EM_GPIO_4 (1 << 4) |
| #define EM_GPIO_5 (1 << 5) |
| #define EM_GPIO_6 (1 << 6) |
| #define EM_GPIO_7 (1 << 7) |
| |
| #define EM_GPO_0 (1 << 0) |
| #define EM_GPO_1 (1 << 1) |
| #define EM_GPO_2 (1 << 2) |
| #define EM_GPO_3 (1 << 3) |
| |
| /* em2800 registers */ |
| #define EM2800_R08_AUDIOSRC 0x08 |
| |
| /* em28xx registers */ |
| |
| #define EM28XX_R00_CHIPCFG 0x00 |
| |
| /* em28xx Chip Configuration 0x00 */ |
| #define EM28XX_CHIPCFG_VENDOR_AUDIO 0x80 |
| #define EM28XX_CHIPCFG_I2S_VOLUME_CAPABLE 0x40 |
| #define EM28XX_CHIPCFG_I2S_5_SAMPRATES 0x30 |
| #define EM28XX_CHIPCFG_I2S_3_SAMPRATES 0x20 |
| #define EM28XX_CHIPCFG_AC97 0x10 |
| #define EM28XX_CHIPCFG_AUDIOMASK 0x30 |
| |
| /* GPIO/GPO registers */ |
| #define EM2880_R04_GPO 0x04 /* em2880-em2883 only */ |
| #define EM28XX_R08_GPIO 0x08 /* em2820 or upper */ |
| |
| #define EM28XX_R06_I2C_CLK 0x06 |
| |
| /* em28xx I2C Clock Register (0x06) */ |
| #define EM28XX_I2C_CLK_ACK_LAST_READ 0x80 |
| #define EM28XX_I2C_CLK_WAIT_ENABLE 0x40 |
| #define EM28XX_I2C_EEPROM_ON_BOARD 0x08 |
| #define EM28XX_I2C_EEPROM_KEY_VALID 0x04 |
| #define EM2874_I2C_SECONDARY_BUS_SELECT 0x04 /* em2874 has two i2c busses */ |
| #define EM28XX_I2C_FREQ_1_5_MHZ 0x03 /* bus frequency (bits [1-0]) */ |
| #define EM28XX_I2C_FREQ_25_KHZ 0x02 |
| #define EM28XX_I2C_FREQ_400_KHZ 0x01 |
| #define EM28XX_I2C_FREQ_100_KHZ 0x00 |
| |
| |
| #define EM28XX_R0A_CHIPID 0x0a |
| #define EM28XX_R0C_USBSUSP 0x0c /* */ |
| |
| #define EM28XX_R0E_AUDIOSRC 0x0e |
| #define EM28XX_R0F_XCLK 0x0f |
| |
| /* em28xx XCLK Register (0x0f) */ |
| #define EM28XX_XCLK_AUDIO_UNMUTE 0x80 /* otherwise audio muted */ |
| #define EM28XX_XCLK_I2S_MSB_TIMING 0x40 /* otherwise standard timing */ |
| #define EM28XX_XCLK_IR_RC5_MODE 0x20 /* otherwise NEC mode */ |
| #define EM28XX_XCLK_IR_NEC_CHK_PARITY 0x10 |
| #define EM28XX_XCLK_FREQUENCY_30MHZ 0x00 /* Freq. select (bits [3-0]) */ |
| #define EM28XX_XCLK_FREQUENCY_15MHZ 0x01 |
| #define EM28XX_XCLK_FREQUENCY_10MHZ 0x02 |
| #define EM28XX_XCLK_FREQUENCY_7_5MHZ 0x03 |
| #define EM28XX_XCLK_FREQUENCY_6MHZ 0x04 |
| #define EM28XX_XCLK_FREQUENCY_5MHZ 0x05 |
| #define EM28XX_XCLK_FREQUENCY_4_3MHZ 0x06 |
| #define EM28XX_XCLK_FREQUENCY_12MHZ 0x07 |
| #define EM28XX_XCLK_FREQUENCY_20MHZ 0x08 |
| #define EM28XX_XCLK_FREQUENCY_20MHZ_2 0x09 |
| #define EM28XX_XCLK_FREQUENCY_48MHZ 0x0a |
| #define EM28XX_XCLK_FREQUENCY_24MHZ 0x0b |
| |
| #define EM28XX_R10_VINMODE 0x10 |
| #define EM28XX_R11_VINCTRL 0x11 |
| #define EM28XX_R12_VINENABLE 0x12 /* */ |
| |
| #define EM28XX_R14_GAMMA 0x14 |
| #define EM28XX_R15_RGAIN 0x15 |
| #define EM28XX_R16_GGAIN 0x16 |
| #define EM28XX_R17_BGAIN 0x17 |
| #define EM28XX_R18_ROFFSET 0x18 |
| #define EM28XX_R19_GOFFSET 0x19 |
| #define EM28XX_R1A_BOFFSET 0x1a |
| |
| #define EM28XX_R1B_OFLOW 0x1b |
| #define EM28XX_R1C_HSTART 0x1c |
| #define EM28XX_R1D_VSTART 0x1d |
| #define EM28XX_R1E_CWIDTH 0x1e |
| #define EM28XX_R1F_CHEIGHT 0x1f |
| |
| #define EM28XX_R20_YGAIN 0x20 |
| #define EM28XX_R21_YOFFSET 0x21 |
| #define EM28XX_R22_UVGAIN 0x22 |
| #define EM28XX_R23_UOFFSET 0x23 |
| #define EM28XX_R24_VOFFSET 0x24 |
| #define EM28XX_R25_SHARPNESS 0x25 |
| |
| #define EM28XX_R26_COMPR 0x26 |
| #define EM28XX_R27_OUTFMT 0x27 |
| |
| /* em28xx Output Format Register (0x27) */ |
| #define EM28XX_OUTFMT_RGB_8_RGRG 0x00 |
| #define EM28XX_OUTFMT_RGB_8_GRGR 0x01 |
| #define EM28XX_OUTFMT_RGB_8_GBGB 0x02 |
| #define EM28XX_OUTFMT_RGB_8_BGBG 0x03 |
| #define EM28XX_OUTFMT_RGB_16_656 0x04 |
| #define EM28XX_OUTFMT_RGB_8_BAYER 0x08 /* Pattern in Reg 0x10[1-0] */ |
| #define EM28XX_OUTFMT_YUV211 0x10 |
| #define EM28XX_OUTFMT_YUV422_Y0UY1V 0x14 |
| #define EM28XX_OUTFMT_YUV422_Y1UY0V 0x15 |
| #define EM28XX_OUTFMT_YUV411 0x18 |
| |
| |
| #define EM28XX_R28_XMIN 0x28 |
| #define EM28XX_R29_XMAX 0x29 |
| #define EM28XX_R2A_YMIN 0x2a |
| #define EM28XX_R2B_YMAX 0x2b |
| |
| #define EM28XX_R30_HSCALELOW 0x30 |
| #define EM28XX_R31_HSCALEHIGH 0x31 |
| #define EM28XX_R32_VSCALELOW 0x32 |
| #define EM28XX_R33_VSCALEHIGH 0x33 |
| |
| #define EM28XX_R40_AC97LSB 0x40 |
| #define EM28XX_R41_AC97MSB 0x41 |
| #define EM28XX_R42_AC97ADDR 0x42 |
| #define EM28XX_R43_AC97BUSY 0x43 |
| |
| #define EM28XX_R45_IR 0x45 |
| /* 0x45 bit 7 - parity bit |
| bits 6-0 - count |
| 0x46 IR brand |
| 0x47 IR data |
| */ |
| |
| /* em2874 registers */ |
| #define EM2874_R50_IR_CONFIG 0x50 |
| #define EM2874_R51_IR 0x51 |
| #define EM2874_R5F_TS_ENABLE 0x5f |
| #define EM2874_R80_GPIO 0x80 |
| |
| /* em2874 IR config register (0x50) */ |
| #define EM2874_IR_NEC 0x00 |
| #define EM2874_IR_RC5 0x04 |
| #define EM2874_IR_RC5_MODE_0 0x08 |
| #define EM2874_IR_RC5_MODE_6A 0x0b |
| |
| /* em2874 Transport Stream Enable Register (0x5f) */ |
| #define EM2874_TS1_CAPTURE_ENABLE (1 << 0) |
| #define EM2874_TS1_FILTER_ENABLE (1 << 1) |
| #define EM2874_TS1_NULL_DISCARD (1 << 2) |
| #define EM2874_TS2_CAPTURE_ENABLE (1 << 4) |
| #define EM2874_TS2_FILTER_ENABLE (1 << 5) |
| #define EM2874_TS2_NULL_DISCARD (1 << 6) |
| |
| /* register settings */ |
| #define EM2800_AUDIO_SRC_TUNER 0x0d |
| #define EM2800_AUDIO_SRC_LINE 0x0c |
| #define EM28XX_AUDIO_SRC_TUNER 0xc0 |
| #define EM28XX_AUDIO_SRC_LINE 0x80 |
| |
| /* FIXME: Need to be populated with the other chip ID's */ |
| enum em28xx_chip_id { |
| CHIP_ID_EM2820 = 18, /* Also used by em2710 */ |
| CHIP_ID_EM2840 = 20, |
| CHIP_ID_EM2750 = 33, |
| CHIP_ID_EM2860 = 34, |
| CHIP_ID_EM2870 = 35, |
| CHIP_ID_EM2883 = 36, |
| CHIP_ID_EM2874 = 65, |
| }; |
| |
| /* |
| * Registers used by em202 and other AC97 chips |
| */ |
| |
| /* Standard AC97 registers */ |
| #define AC97_RESET 0x00 |
| |
| /* Output volumes */ |
| #define AC97_MASTER_VOL 0x02 |
| #define AC97_LINE_LEVEL_VOL 0x04 /* Some devices use for headphones */ |
| #define AC97_MASTER_MONO_VOL 0x06 |
| |
| /* Input volumes */ |
| #define AC97_PC_BEEP_VOL 0x0a |
| #define AC97_PHONE_VOL 0x0c |
| #define AC97_MIC_VOL 0x0e |
| #define AC97_LINEIN_VOL 0x10 |
| #define AC97_CD_VOL 0x12 |
| #define AC97_VIDEO_VOL 0x14 |
| #define AC97_AUX_VOL 0x16 |
| #define AC97_PCM_OUT_VOL 0x18 |
| |
| /* capture registers */ |
| #define AC97_RECORD_SELECT 0x1a |
| #define AC97_RECORD_GAIN 0x1c |
| |
| /* control registers */ |
| #define AC97_GENERAL_PURPOSE 0x20 |
| #define AC97_3D_CTRL 0x22 |
| #define AC97_AUD_INT_AND_PAG 0x24 |
| #define AC97_POWER_DOWN_CTRL 0x26 |
| #define AC97_EXT_AUD_ID 0x28 |
| #define AC97_EXT_AUD_CTRL 0x2a |
| |
| /* Supported rate varies for each AC97 device |
| if write an unsupported value, it will return the closest one |
| */ |
| #define AC97_PCM_OUT_FRONT_SRATE 0x2c |
| #define AC97_PCM_OUT_SURR_SRATE 0x2e |
| #define AC97_PCM_OUT_LFE_SRATE 0x30 |
| #define AC97_PCM_IN_SRATE 0x32 |
| |
| /* For devices with more than 2 channels, extra output volumes */ |
| #define AC97_LFE_MASTER_VOL 0x36 |
| #define AC97_SURR_MASTER_VOL 0x38 |
| |
| /* Digital SPDIF output control */ |
| #define AC97_SPDIF_OUT_CTRL 0x3a |
| |
| /* Vendor ID identifier */ |
| #define AC97_VENDOR_ID1 0x7c |
| #define AC97_VENDOR_ID2 0x7e |
| |
| /* EMP202 vendor registers */ |
| #define EM202_EXT_MODEM_CTRL 0x3e |
| #define EM202_GPIO_CONF 0x4c |
| #define EM202_GPIO_POLARITY 0x4e |
| #define EM202_GPIO_STICKY 0x50 |
| #define EM202_GPIO_MASK 0x52 |
| #define EM202_GPIO_STATUS 0x54 |
| #define EM202_SPDIF_OUT_SEL 0x6a |
| #define EM202_ANTIPOP 0x72 |
| #define EM202_EAPD_GPIO_ACCESS 0x74 |