| /* |
| * Device Tree Source for AM33XX SoC |
| * |
| * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ |
| * |
| * This file is licensed under the terms of the GNU General Public License |
| * version 2. This program is licensed "as is" without any warranty of any |
| * kind, whether express or implied. |
| */ |
| |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/pinctrl/am33xx.h> |
| |
| / { |
| compatible = "ti,am33xx"; |
| interrupt-parent = <&intc>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| chosen { }; |
| |
| aliases { |
| i2c0 = &i2c0; |
| i2c1 = &i2c1; |
| i2c2 = &i2c2; |
| serial0 = &uart0; |
| serial1 = &uart1; |
| serial2 = &uart2; |
| serial3 = &uart3; |
| serial4 = &uart4; |
| serial5 = &uart5; |
| d_can0 = &dcan0; |
| d_can1 = &dcan1; |
| usb0 = &usb0; |
| usb1 = &usb1; |
| phy0 = &usb0_phy; |
| phy1 = &usb1_phy; |
| ethernet0 = &cpsw_emac0; |
| ethernet1 = &cpsw_emac1; |
| spi0 = &spi0; |
| spi1 = &spi1; |
| mmc0 = &mmc1; |
| mmc1 = &mmc2; |
| mmc2 = &mmc3; |
| }; |
| |
| cpus { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| cpu@0 { |
| compatible = "arm,cortex-a8"; |
| device_type = "cpu"; |
| reg = <0>; |
| |
| operating-points-v2 = <&cpu0_opp_table>; |
| |
| clocks = <&dpll_mpu_ck>; |
| clock-names = "cpu"; |
| |
| clock-latency = <300000>; /* From omap-cpufreq driver */ |
| }; |
| }; |
| |
| cpu0_opp_table: opp-table { |
| compatible = "operating-points-v2-ti-cpu"; |
| syscon = <&scm_conf>; |
| |
| /* |
| * The three following nodes are marked with opp-suspend |
| * because the can not be enabled simultaneously on a |
| * single SoC. |
| */ |
| opp50-300000000 { |
| opp-hz = /bits/ 64 <300000000>; |
| opp-microvolt = <950000 931000 969000>; |
| opp-supported-hw = <0x06 0x0010>; |
| opp-suspend; |
| }; |
| |
| opp100-275000000 { |
| opp-hz = /bits/ 64 <275000000>; |
| opp-microvolt = <1100000 1078000 1122000>; |
| opp-supported-hw = <0x01 0x00FF>; |
| opp-suspend; |
| }; |
| |
| opp100-300000000 { |
| opp-hz = /bits/ 64 <300000000>; |
| opp-microvolt = <1100000 1078000 1122000>; |
| opp-supported-hw = <0x06 0x0020>; |
| opp-suspend; |
| }; |
| |
| opp100-500000000 { |
| opp-hz = /bits/ 64 <500000000>; |
| opp-microvolt = <1100000 1078000 1122000>; |
| opp-supported-hw = <0x01 0xFFFF>; |
| }; |
| |
| opp100-600000000 { |
| opp-hz = /bits/ 64 <600000000>; |
| opp-microvolt = <1100000 1078000 1122000>; |
| opp-supported-hw = <0x06 0x0040>; |
| }; |
| |
| opp120-600000000 { |
| opp-hz = /bits/ 64 <600000000>; |
| opp-microvolt = <1200000 1176000 1224000>; |
| opp-supported-hw = <0x01 0xFFFF>; |
| }; |
| |
| opp120-720000000 { |
| opp-hz = /bits/ 64 <720000000>; |
| opp-microvolt = <1200000 1176000 1224000>; |
| opp-supported-hw = <0x06 0x0080>; |
| }; |
| |
| oppturbo-720000000 { |
| opp-hz = /bits/ 64 <720000000>; |
| opp-microvolt = <1260000 1234800 1285200>; |
| opp-supported-hw = <0x01 0xFFFF>; |
| }; |
| |
| oppturbo-800000000 { |
| opp-hz = /bits/ 64 <800000000>; |
| opp-microvolt = <1260000 1234800 1285200>; |
| opp-supported-hw = <0x06 0x0100>; |
| }; |
| |
| oppnitro-1000000000 { |
| opp-hz = /bits/ 64 <1000000000>; |
| opp-microvolt = <1325000 1298500 1351500>; |
| opp-supported-hw = <0x04 0x0200>; |
| }; |
| }; |
| |
| pmu { |
| compatible = "arm,cortex-a8-pmu"; |
| interrupts = <3>; |
| }; |
| |
| /* |
| * The soc node represents the soc top level view. It is used for IPs |
| * that are not memory mapped in the MPU view or for the MPU itself. |
| */ |
| soc { |
| compatible = "ti,omap-infra"; |
| mpu { |
| compatible = "ti,omap3-mpu"; |
| ti,hwmods = "mpu"; |
| }; |
| }; |
| |
| /* |
| * XXX: Use a flat representation of the AM33XX interconnect. |
| * The real AM33XX interconnect network is quite complex. Since |
| * it will not bring real advantage to represent that in DT |
| * for the moment, just use a fake OCP bus entry to represent |
| * the whole bus hierarchy. |
| */ |
| ocp { |
| compatible = "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| ti,hwmods = "l3_main"; |
| |
| l4_wkup: l4_wkup@44c00000 { |
| compatible = "ti,am3-l4-wkup", "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0 0x44c00000 0x280000>; |
| |
| wkup_m3: wkup_m3@100000 { |
| compatible = "ti,am3352-wkup-m3"; |
| reg = <0x100000 0x4000>, |
| <0x180000 0x2000>; |
| reg-names = "umem", "dmem"; |
| ti,hwmods = "wkup_m3"; |
| ti,pm-firmware = "am335x-pm-firmware.elf"; |
| }; |
| |
| prcm: prcm@200000 { |
| compatible = "ti,am3-prcm"; |
| reg = <0x200000 0x4000>; |
| |
| prcm_clocks: clocks { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| |
| prcm_clockdomains: clockdomains { |
| }; |
| }; |
| |
| scm: scm@210000 { |
| compatible = "ti,am3-scm", "simple-bus"; |
| reg = <0x210000 0x2000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| #pinctrl-cells = <1>; |
| ranges = <0 0x210000 0x2000>; |
| |
| am33xx_pinmux: pinmux@800 { |
| compatible = "pinctrl-single"; |
| reg = <0x800 0x238>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #pinctrl-cells = <1>; |
| pinctrl-single,register-width = <32>; |
| pinctrl-single,function-mask = <0x7f>; |
| }; |
| |
| scm_conf: scm_conf@0 { |
| compatible = "syscon", "simple-bus"; |
| reg = <0x0 0x800>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0 0 0x800>; |
| |
| scm_clocks: clocks { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| }; |
| |
| wkup_m3_ipc: wkup_m3_ipc@1324 { |
| compatible = "ti,am3352-wkup-m3-ipc"; |
| reg = <0x1324 0x24>; |
| interrupts = <78>; |
| ti,rproc = <&wkup_m3>; |
| mboxes = <&mailbox &mbox_wkupm3>; |
| }; |
| |
| edma_xbar: dma-router@f90 { |
| compatible = "ti,am335x-edma-crossbar"; |
| reg = <0xf90 0x40>; |
| #dma-cells = <3>; |
| dma-requests = <32>; |
| dma-masters = <&edma>; |
| }; |
| |
| scm_clockdomains: clockdomains { |
| }; |
| }; |
| }; |
| |
| intc: interrupt-controller@48200000 { |
| compatible = "ti,am33xx-intc"; |
| interrupt-controller; |
| #interrupt-cells = <1>; |
| reg = <0x48200000 0x1000>; |
| }; |
| |
| edma: edma@49000000 { |
| compatible = "ti,edma3-tpcc"; |
| ti,hwmods = "tpcc"; |
| reg = <0x49000000 0x10000>; |
| reg-names = "edma3_cc"; |
| interrupts = <12 13 14>; |
| interrupt-names = "edma3_ccint", "edma3_mperr", |
| "edma3_ccerrint"; |
| dma-requests = <64>; |
| #dma-cells = <2>; |
| |
| ti,tptcs = <&edma_tptc0 7>, <&edma_tptc1 5>, |
| <&edma_tptc2 0>; |
| |
| ti,edma-memcpy-channels = <20 21>; |
| }; |
| |
| edma_tptc0: tptc@49800000 { |
| compatible = "ti,edma3-tptc"; |
| ti,hwmods = "tptc0"; |
| reg = <0x49800000 0x100000>; |
| interrupts = <112>; |
| interrupt-names = "edma3_tcerrint"; |
| }; |
| |
| edma_tptc1: tptc@49900000 { |
| compatible = "ti,edma3-tptc"; |
| ti,hwmods = "tptc1"; |
| reg = <0x49900000 0x100000>; |
| interrupts = <113>; |
| interrupt-names = "edma3_tcerrint"; |
| }; |
| |
| edma_tptc2: tptc@49a00000 { |
| compatible = "ti,edma3-tptc"; |
| ti,hwmods = "tptc2"; |
| reg = <0x49a00000 0x100000>; |
| interrupts = <114>; |
| interrupt-names = "edma3_tcerrint"; |
| }; |
| |
| gpio0: gpio@44e07000 { |
| compatible = "ti,omap4-gpio"; |
| ti,hwmods = "gpio1"; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| reg = <0x44e07000 0x1000>; |
| interrupts = <96>; |
| }; |
| |
| gpio1: gpio@4804c000 { |
| compatible = "ti,omap4-gpio"; |
| ti,hwmods = "gpio2"; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| reg = <0x4804c000 0x1000>; |
| interrupts = <98>; |
| }; |
| |
| gpio2: gpio@481ac000 { |
| compatible = "ti,omap4-gpio"; |
| ti,hwmods = "gpio3"; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| reg = <0x481ac000 0x1000>; |
| interrupts = <32>; |
| }; |
| |
| gpio3: gpio@481ae000 { |
| compatible = "ti,omap4-gpio"; |
| ti,hwmods = "gpio4"; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| reg = <0x481ae000 0x1000>; |
| interrupts = <62>; |
| }; |
| |
| uart0: serial@44e09000 { |
| compatible = "ti,am3352-uart", "ti,omap3-uart"; |
| ti,hwmods = "uart1"; |
| clock-frequency = <48000000>; |
| reg = <0x44e09000 0x2000>; |
| interrupts = <72>; |
| status = "disabled"; |
| dmas = <&edma 26 0>, <&edma 27 0>; |
| dma-names = "tx", "rx"; |
| }; |
| |
| uart1: serial@48022000 { |
| compatible = "ti,am3352-uart", "ti,omap3-uart"; |
| ti,hwmods = "uart2"; |
| clock-frequency = <48000000>; |
| reg = <0x48022000 0x2000>; |
| interrupts = <73>; |
| status = "disabled"; |
| dmas = <&edma 28 0>, <&edma 29 0>; |
| dma-names = "tx", "rx"; |
| }; |
| |
| uart2: serial@48024000 { |
| compatible = "ti,am3352-uart", "ti,omap3-uart"; |
| ti,hwmods = "uart3"; |
| clock-frequency = <48000000>; |
| reg = <0x48024000 0x2000>; |
| interrupts = <74>; |
| status = "disabled"; |
| dmas = <&edma 30 0>, <&edma 31 0>; |
| dma-names = "tx", "rx"; |
| }; |
| |
| uart3: serial@481a6000 { |
| compatible = "ti,am3352-uart", "ti,omap3-uart"; |
| ti,hwmods = "uart4"; |
| clock-frequency = <48000000>; |
| reg = <0x481a6000 0x2000>; |
| interrupts = <44>; |
| status = "disabled"; |
| }; |
| |
| uart4: serial@481a8000 { |
| compatible = "ti,am3352-uart", "ti,omap3-uart"; |
| ti,hwmods = "uart5"; |
| clock-frequency = <48000000>; |
| reg = <0x481a8000 0x2000>; |
| interrupts = <45>; |
| status = "disabled"; |
| }; |
| |
| uart5: serial@481aa000 { |
| compatible = "ti,am3352-uart", "ti,omap3-uart"; |
| ti,hwmods = "uart6"; |
| clock-frequency = <48000000>; |
| reg = <0x481aa000 0x2000>; |
| interrupts = <46>; |
| status = "disabled"; |
| }; |
| |
| i2c0: i2c@44e0b000 { |
| compatible = "ti,omap4-i2c"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| ti,hwmods = "i2c1"; |
| reg = <0x44e0b000 0x1000>; |
| interrupts = <70>; |
| status = "disabled"; |
| }; |
| |
| i2c1: i2c@4802a000 { |
| compatible = "ti,omap4-i2c"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| ti,hwmods = "i2c2"; |
| reg = <0x4802a000 0x1000>; |
| interrupts = <71>; |
| status = "disabled"; |
| }; |
| |
| i2c2: i2c@4819c000 { |
| compatible = "ti,omap4-i2c"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| ti,hwmods = "i2c3"; |
| reg = <0x4819c000 0x1000>; |
| interrupts = <30>; |
| status = "disabled"; |
| }; |
| |
| mmc1: mmc@48060000 { |
| compatible = "ti,omap4-hsmmc"; |
| ti,hwmods = "mmc1"; |
| ti,dual-volt; |
| ti,needs-special-reset; |
| ti,needs-special-hs-handling; |
| dmas = <&edma_xbar 24 0 0 |
| &edma_xbar 25 0 0>; |
| dma-names = "tx", "rx"; |
| interrupts = <64>; |
| reg = <0x48060000 0x1000>; |
| status = "disabled"; |
| }; |
| |
| mmc2: mmc@481d8000 { |
| compatible = "ti,omap4-hsmmc"; |
| ti,hwmods = "mmc2"; |
| ti,needs-special-reset; |
| dmas = <&edma 2 0 |
| &edma 3 0>; |
| dma-names = "tx", "rx"; |
| interrupts = <28>; |
| reg = <0x481d8000 0x1000>; |
| status = "disabled"; |
| }; |
| |
| mmc3: mmc@47810000 { |
| compatible = "ti,omap4-hsmmc"; |
| ti,hwmods = "mmc3"; |
| ti,needs-special-reset; |
| interrupts = <29>; |
| reg = <0x47810000 0x1000>; |
| status = "disabled"; |
| }; |
| |
| hwspinlock: spinlock@480ca000 { |
| compatible = "ti,omap4-hwspinlock"; |
| reg = <0x480ca000 0x1000>; |
| ti,hwmods = "spinlock"; |
| #hwlock-cells = <1>; |
| }; |
| |
| wdt2: wdt@44e35000 { |
| compatible = "ti,omap3-wdt"; |
| ti,hwmods = "wd_timer2"; |
| reg = <0x44e35000 0x1000>; |
| interrupts = <91>; |
| }; |
| |
| dcan0: can@481cc000 { |
| compatible = "ti,am3352-d_can"; |
| ti,hwmods = "d_can0"; |
| reg = <0x481cc000 0x2000>; |
| clocks = <&dcan0_fck>; |
| clock-names = "fck"; |
| syscon-raminit = <&scm_conf 0x644 0>; |
| interrupts = <52>; |
| status = "disabled"; |
| }; |
| |
| dcan1: can@481d0000 { |
| compatible = "ti,am3352-d_can"; |
| ti,hwmods = "d_can1"; |
| reg = <0x481d0000 0x2000>; |
| clocks = <&dcan1_fck>; |
| clock-names = "fck"; |
| syscon-raminit = <&scm_conf 0x644 1>; |
| interrupts = <55>; |
| status = "disabled"; |
| }; |
| |
| mailbox: mailbox@480C8000 { |
| compatible = "ti,omap4-mailbox"; |
| reg = <0x480C8000 0x200>; |
| interrupts = <77>; |
| ti,hwmods = "mailbox"; |
| #mbox-cells = <1>; |
| ti,mbox-num-users = <4>; |
| ti,mbox-num-fifos = <8>; |
| mbox_wkupm3: wkup_m3 { |
| ti,mbox-send-noirq; |
| ti,mbox-tx = <0 0 0>; |
| ti,mbox-rx = <0 0 3>; |
| }; |
| }; |
| |
| timer1: timer@44e31000 { |
| compatible = "ti,am335x-timer-1ms"; |
| reg = <0x44e31000 0x400>; |
| interrupts = <67>; |
| ti,hwmods = "timer1"; |
| ti,timer-alwon; |
| }; |
| |
| timer2: timer@48040000 { |
| compatible = "ti,am335x-timer"; |
| reg = <0x48040000 0x400>; |
| interrupts = <68>; |
| ti,hwmods = "timer2"; |
| }; |
| |
| timer3: timer@48042000 { |
| compatible = "ti,am335x-timer"; |
| reg = <0x48042000 0x400>; |
| interrupts = <69>; |
| ti,hwmods = "timer3"; |
| }; |
| |
| timer4: timer@48044000 { |
| compatible = "ti,am335x-timer"; |
| reg = <0x48044000 0x400>; |
| interrupts = <92>; |
| ti,hwmods = "timer4"; |
| ti,timer-pwm; |
| }; |
| |
| timer5: timer@48046000 { |
| compatible = "ti,am335x-timer"; |
| reg = <0x48046000 0x400>; |
| interrupts = <93>; |
| ti,hwmods = "timer5"; |
| ti,timer-pwm; |
| }; |
| |
| timer6: timer@48048000 { |
| compatible = "ti,am335x-timer"; |
| reg = <0x48048000 0x400>; |
| interrupts = <94>; |
| ti,hwmods = "timer6"; |
| ti,timer-pwm; |
| }; |
| |
| timer7: timer@4804a000 { |
| compatible = "ti,am335x-timer"; |
| reg = <0x4804a000 0x400>; |
| interrupts = <95>; |
| ti,hwmods = "timer7"; |
| ti,timer-pwm; |
| }; |
| |
| rtc: rtc@44e3e000 { |
| compatible = "ti,am3352-rtc", "ti,da830-rtc"; |
| reg = <0x44e3e000 0x1000>; |
| interrupts = <75 |
| 76>; |
| ti,hwmods = "rtc"; |
| clocks = <&clkdiv32k_ick>; |
| clock-names = "int-clk"; |
| }; |
| |
| spi0: spi@48030000 { |
| compatible = "ti,omap4-mcspi"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x48030000 0x400>; |
| interrupts = <65>; |
| ti,spi-num-cs = <2>; |
| ti,hwmods = "spi0"; |
| dmas = <&edma 16 0 |
| &edma 17 0 |
| &edma 18 0 |
| &edma 19 0>; |
| dma-names = "tx0", "rx0", "tx1", "rx1"; |
| status = "disabled"; |
| }; |
| |
| spi1: spi@481a0000 { |
| compatible = "ti,omap4-mcspi"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x481a0000 0x400>; |
| interrupts = <125>; |
| ti,spi-num-cs = <2>; |
| ti,hwmods = "spi1"; |
| dmas = <&edma 42 0 |
| &edma 43 0 |
| &edma 44 0 |
| &edma 45 0>; |
| dma-names = "tx0", "rx0", "tx1", "rx1"; |
| status = "disabled"; |
| }; |
| |
| usb: usb@47400000 { |
| compatible = "ti,am33xx-usb"; |
| reg = <0x47400000 0x1000>; |
| ranges; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ti,hwmods = "usb_otg_hs"; |
| status = "disabled"; |
| |
| usb_ctrl_mod: control@44e10620 { |
| compatible = "ti,am335x-usb-ctrl-module"; |
| reg = <0x44e10620 0x10 |
| 0x44e10648 0x4>; |
| reg-names = "phy_ctrl", "wakeup"; |
| status = "disabled"; |
| }; |
| |
| usb0_phy: usb-phy@47401300 { |
| compatible = "ti,am335x-usb-phy"; |
| reg = <0x47401300 0x100>; |
| reg-names = "phy"; |
| status = "disabled"; |
| ti,ctrl_mod = <&usb_ctrl_mod>; |
| }; |
| |
| usb0: usb@47401000 { |
| compatible = "ti,musb-am33xx"; |
| status = "disabled"; |
| reg = <0x47401400 0x400 |
| 0x47401000 0x200>; |
| reg-names = "mc", "control"; |
| |
| interrupts = <18>; |
| interrupt-names = "mc"; |
| dr_mode = "otg"; |
| mentor,multipoint = <1>; |
| mentor,num-eps = <16>; |
| mentor,ram-bits = <12>; |
| mentor,power = <500>; |
| phys = <&usb0_phy>; |
| |
| dmas = <&cppi41dma 0 0 &cppi41dma 1 0 |
| &cppi41dma 2 0 &cppi41dma 3 0 |
| &cppi41dma 4 0 &cppi41dma 5 0 |
| &cppi41dma 6 0 &cppi41dma 7 0 |
| &cppi41dma 8 0 &cppi41dma 9 0 |
| &cppi41dma 10 0 &cppi41dma 11 0 |
| &cppi41dma 12 0 &cppi41dma 13 0 |
| &cppi41dma 14 0 &cppi41dma 0 1 |
| &cppi41dma 1 1 &cppi41dma 2 1 |
| &cppi41dma 3 1 &cppi41dma 4 1 |
| &cppi41dma 5 1 &cppi41dma 6 1 |
| &cppi41dma 7 1 &cppi41dma 8 1 |
| &cppi41dma 9 1 &cppi41dma 10 1 |
| &cppi41dma 11 1 &cppi41dma 12 1 |
| &cppi41dma 13 1 &cppi41dma 14 1>; |
| dma-names = |
| "rx1", "rx2", "rx3", "rx4", "rx5", "rx6", "rx7", |
| "rx8", "rx9", "rx10", "rx11", "rx12", "rx13", |
| "rx14", "rx15", |
| "tx1", "tx2", "tx3", "tx4", "tx5", "tx6", "tx7", |
| "tx8", "tx9", "tx10", "tx11", "tx12", "tx13", |
| "tx14", "tx15"; |
| }; |
| |
| usb1_phy: usb-phy@47401b00 { |
| compatible = "ti,am335x-usb-phy"; |
| reg = <0x47401b00 0x100>; |
| reg-names = "phy"; |
| status = "disabled"; |
| ti,ctrl_mod = <&usb_ctrl_mod>; |
| }; |
| |
| usb1: usb@47401800 { |
| compatible = "ti,musb-am33xx"; |
| status = "disabled"; |
| reg = <0x47401c00 0x400 |
| 0x47401800 0x200>; |
| reg-names = "mc", "control"; |
| interrupts = <19>; |
| interrupt-names = "mc"; |
| dr_mode = "otg"; |
| mentor,multipoint = <1>; |
| mentor,num-eps = <16>; |
| mentor,ram-bits = <12>; |
| mentor,power = <500>; |
| phys = <&usb1_phy>; |
| |
| dmas = <&cppi41dma 15 0 &cppi41dma 16 0 |
| &cppi41dma 17 0 &cppi41dma 18 0 |
| &cppi41dma 19 0 &cppi41dma 20 0 |
| &cppi41dma 21 0 &cppi41dma 22 0 |
| &cppi41dma 23 0 &cppi41dma 24 0 |
| &cppi41dma 25 0 &cppi41dma 26 0 |
| &cppi41dma 27 0 &cppi41dma 28 0 |
| &cppi41dma 29 0 &cppi41dma 15 1 |
| &cppi41dma 16 1 &cppi41dma 17 1 |
| &cppi41dma 18 1 &cppi41dma 19 1 |
| &cppi41dma 20 1 &cppi41dma 21 1 |
| &cppi41dma 22 1 &cppi41dma 23 1 |
| &cppi41dma 24 1 &cppi41dma 25 1 |
| &cppi41dma 26 1 &cppi41dma 27 1 |
| &cppi41dma 28 1 &cppi41dma 29 1>; |
| dma-names = |
| "rx1", "rx2", "rx3", "rx4", "rx5", "rx6", "rx7", |
| "rx8", "rx9", "rx10", "rx11", "rx12", "rx13", |
| "rx14", "rx15", |
| "tx1", "tx2", "tx3", "tx4", "tx5", "tx6", "tx7", |
| "tx8", "tx9", "tx10", "tx11", "tx12", "tx13", |
| "tx14", "tx15"; |
| }; |
| |
| cppi41dma: dma-controller@47402000 { |
| compatible = "ti,am3359-cppi41"; |
| reg = <0x47400000 0x1000 |
| 0x47402000 0x1000 |
| 0x47403000 0x1000 |
| 0x47404000 0x4000>; |
| reg-names = "glue", "controller", "scheduler", "queuemgr"; |
| interrupts = <17>; |
| interrupt-names = "glue"; |
| #dma-cells = <2>; |
| #dma-channels = <30>; |
| #dma-requests = <256>; |
| status = "disabled"; |
| }; |
| }; |
| |
| epwmss0: epwmss@48300000 { |
| compatible = "ti,am33xx-pwmss"; |
| reg = <0x48300000 0x10>; |
| ti,hwmods = "epwmss0"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| status = "disabled"; |
| ranges = <0x48300100 0x48300100 0x80 /* ECAP */ |
| 0x48300180 0x48300180 0x80 /* EQEP */ |
| 0x48300200 0x48300200 0x80>; /* EHRPWM */ |
| |
| ecap0: ecap@48300100 { |
| compatible = "ti,am3352-ecap", |
| "ti,am33xx-ecap"; |
| #pwm-cells = <3>; |
| reg = <0x48300100 0x80>; |
| clocks = <&l4ls_gclk>; |
| clock-names = "fck"; |
| interrupts = <31>; |
| interrupt-names = "ecap0"; |
| status = "disabled"; |
| }; |
| |
| ehrpwm0: pwm@48300200 { |
| compatible = "ti,am3352-ehrpwm", |
| "ti,am33xx-ehrpwm"; |
| #pwm-cells = <3>; |
| reg = <0x48300200 0x80>; |
| clocks = <&ehrpwm0_tbclk>, <&l4ls_gclk>; |
| clock-names = "tbclk", "fck"; |
| status = "disabled"; |
| }; |
| }; |
| |
| epwmss1: epwmss@48302000 { |
| compatible = "ti,am33xx-pwmss"; |
| reg = <0x48302000 0x10>; |
| ti,hwmods = "epwmss1"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| status = "disabled"; |
| ranges = <0x48302100 0x48302100 0x80 /* ECAP */ |
| 0x48302180 0x48302180 0x80 /* EQEP */ |
| 0x48302200 0x48302200 0x80>; /* EHRPWM */ |
| |
| ecap1: ecap@48302100 { |
| compatible = "ti,am3352-ecap", |
| "ti,am33xx-ecap"; |
| #pwm-cells = <3>; |
| reg = <0x48302100 0x80>; |
| clocks = <&l4ls_gclk>; |
| clock-names = "fck"; |
| interrupts = <47>; |
| interrupt-names = "ecap1"; |
| status = "disabled"; |
| }; |
| |
| ehrpwm1: pwm@48302200 { |
| compatible = "ti,am3352-ehrpwm", |
| "ti,am33xx-ehrpwm"; |
| #pwm-cells = <3>; |
| reg = <0x48302200 0x80>; |
| clocks = <&ehrpwm1_tbclk>, <&l4ls_gclk>; |
| clock-names = "tbclk", "fck"; |
| status = "disabled"; |
| }; |
| }; |
| |
| epwmss2: epwmss@48304000 { |
| compatible = "ti,am33xx-pwmss"; |
| reg = <0x48304000 0x10>; |
| ti,hwmods = "epwmss2"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| status = "disabled"; |
| ranges = <0x48304100 0x48304100 0x80 /* ECAP */ |
| 0x48304180 0x48304180 0x80 /* EQEP */ |
| 0x48304200 0x48304200 0x80>; /* EHRPWM */ |
| |
| ecap2: ecap@48304100 { |
| compatible = "ti,am3352-ecap", |
| "ti,am33xx-ecap"; |
| #pwm-cells = <3>; |
| reg = <0x48304100 0x80>; |
| clocks = <&l4ls_gclk>; |
| clock-names = "fck"; |
| interrupts = <61>; |
| interrupt-names = "ecap2"; |
| status = "disabled"; |
| }; |
| |
| ehrpwm2: pwm@48304200 { |
| compatible = "ti,am3352-ehrpwm", |
| "ti,am33xx-ehrpwm"; |
| #pwm-cells = <3>; |
| reg = <0x48304200 0x80>; |
| clocks = <&ehrpwm2_tbclk>, <&l4ls_gclk>; |
| clock-names = "tbclk", "fck"; |
| status = "disabled"; |
| }; |
| }; |
| |
| mac: ethernet@4a100000 { |
| compatible = "ti,am335x-cpsw","ti,cpsw"; |
| ti,hwmods = "cpgmac0"; |
| clocks = <&cpsw_125mhz_gclk>, <&cpsw_cpts_rft_clk>; |
| clock-names = "fck", "cpts"; |
| cpdma_channels = <8>; |
| ale_entries = <1024>; |
| bd_ram_size = <0x2000>; |
| mac_control = <0x20>; |
| slaves = <2>; |
| active_slave = <0>; |
| cpts_clock_mult = <0x80000000>; |
| cpts_clock_shift = <29>; |
| reg = <0x4a100000 0x800 |
| 0x4a101200 0x100>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| /* |
| * c0_rx_thresh_pend |
| * c0_rx_pend |
| * c0_tx_pend |
| * c0_misc_pend |
| */ |
| interrupts = <40 41 42 43>; |
| ranges; |
| syscon = <&scm_conf>; |
| status = "disabled"; |
| |
| davinci_mdio: mdio@4a101000 { |
| compatible = "ti,cpsw-mdio","ti,davinci_mdio"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| ti,hwmods = "davinci_mdio"; |
| bus_freq = <1000000>; |
| reg = <0x4a101000 0x100>; |
| status = "disabled"; |
| }; |
| |
| cpsw_emac0: slave@4a100200 { |
| /* Filled in by U-Boot */ |
| mac-address = [ 00 00 00 00 00 00 ]; |
| }; |
| |
| cpsw_emac1: slave@4a100300 { |
| /* Filled in by U-Boot */ |
| mac-address = [ 00 00 00 00 00 00 ]; |
| }; |
| |
| phy_sel: cpsw-phy-sel@44e10650 { |
| compatible = "ti,am3352-cpsw-phy-sel"; |
| reg= <0x44e10650 0x4>; |
| reg-names = "gmii-sel"; |
| }; |
| }; |
| |
| ocmcram: ocmcram@40300000 { |
| compatible = "mmio-sram"; |
| reg = <0x40300000 0x10000>; /* 64k */ |
| }; |
| |
| elm: elm@48080000 { |
| compatible = "ti,am3352-elm"; |
| reg = <0x48080000 0x2000>; |
| interrupts = <4>; |
| ti,hwmods = "elm"; |
| status = "disabled"; |
| }; |
| |
| lcdc: lcdc@4830e000 { |
| compatible = "ti,am33xx-tilcdc"; |
| reg = <0x4830e000 0x1000>; |
| interrupts = <36>; |
| ti,hwmods = "lcdc"; |
| status = "disabled"; |
| }; |
| |
| tscadc: tscadc@44e0d000 { |
| compatible = "ti,am3359-tscadc"; |
| reg = <0x44e0d000 0x1000>; |
| interrupts = <16>; |
| ti,hwmods = "adc_tsc"; |
| status = "disabled"; |
| dmas = <&edma 53 0>, <&edma 57 0>; |
| dma-names = "fifo0", "fifo1"; |
| |
| tsc { |
| compatible = "ti,am3359-tsc"; |
| }; |
| am335x_adc: adc { |
| #io-channel-cells = <1>; |
| compatible = "ti,am3359-adc"; |
| }; |
| }; |
| |
| gpmc: gpmc@50000000 { |
| compatible = "ti,am3352-gpmc"; |
| ti,hwmods = "gpmc"; |
| ti,no-idle-on-init; |
| reg = <0x50000000 0x2000>; |
| interrupts = <100>; |
| dmas = <&edma 52 0>; |
| dma-names = "rxtx"; |
| gpmc,num-cs = <7>; |
| gpmc,num-waitpins = <2>; |
| #address-cells = <2>; |
| #size-cells = <1>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| status = "disabled"; |
| }; |
| |
| sham: sham@53100000 { |
| compatible = "ti,omap4-sham"; |
| ti,hwmods = "sham"; |
| reg = <0x53100000 0x200>; |
| interrupts = <109>; |
| dmas = <&edma 36 0>; |
| dma-names = "rx"; |
| }; |
| |
| aes: aes@53500000 { |
| compatible = "ti,omap4-aes"; |
| ti,hwmods = "aes"; |
| reg = <0x53500000 0xa0>; |
| interrupts = <103>; |
| dmas = <&edma 6 0>, |
| <&edma 5 0>; |
| dma-names = "tx", "rx"; |
| }; |
| |
| mcasp0: mcasp@48038000 { |
| compatible = "ti,am33xx-mcasp-audio"; |
| ti,hwmods = "mcasp0"; |
| reg = <0x48038000 0x2000>, |
| <0x46000000 0x400000>; |
| reg-names = "mpu", "dat"; |
| interrupts = <80>, <81>; |
| interrupt-names = "tx", "rx"; |
| status = "disabled"; |
| dmas = <&edma 8 2>, |
| <&edma 9 2>; |
| dma-names = "tx", "rx"; |
| }; |
| |
| mcasp1: mcasp@4803C000 { |
| compatible = "ti,am33xx-mcasp-audio"; |
| ti,hwmods = "mcasp1"; |
| reg = <0x4803C000 0x2000>, |
| <0x46400000 0x400000>; |
| reg-names = "mpu", "dat"; |
| interrupts = <82>, <83>; |
| interrupt-names = "tx", "rx"; |
| status = "disabled"; |
| dmas = <&edma 10 2>, |
| <&edma 11 2>; |
| dma-names = "tx", "rx"; |
| }; |
| |
| rng: rng@48310000 { |
| compatible = "ti,omap4-rng"; |
| ti,hwmods = "rng"; |
| reg = <0x48310000 0x2000>; |
| interrupts = <111>; |
| }; |
| }; |
| }; |
| |
| /include/ "am33xx-clocks.dtsi" |