| Freescale Synchronous Serial Interface |
| |
| The SSI is a serial device that communicates with audio codecs. It can |
| be programmed in AC97, I2S, left-justified, or right-justified modes. |
| |
| Required properties: |
| - compatible: Compatible list, contains "fsl,ssi". |
| - cell-index: The SSI, <0> = SSI1, <1> = SSI2, and so on. |
| - reg: Offset and length of the register set for the device. |
| - interrupts: <a b> where a is the interrupt number and b is a |
| field that represents an encoding of the sense and |
| level information for the interrupt. This should be |
| encoded based on the information in section 2) |
| depending on the type of interrupt controller you |
| have. |
| - interrupt-parent: The phandle for the interrupt controller that |
| services interrupts for this device. |
| - fsl,mode: The operating mode for the SSI interface. |
| "i2s-slave" - I2S mode, SSI is clock slave |
| "i2s-master" - I2S mode, SSI is clock master |
| "lj-slave" - left-justified mode, SSI is clock slave |
| "lj-master" - l.j. mode, SSI is clock master |
| "rj-slave" - right-justified mode, SSI is clock slave |
| "rj-master" - r.j., SSI is clock master |
| "ac97-slave" - AC97 mode, SSI is clock slave |
| "ac97-master" - AC97 mode, SSI is clock master |
| - fsl,playback-dma: Phandle to a node for the DMA channel to use for |
| playback of audio. This is typically dictated by SOC |
| design. See the notes below. |
| - fsl,capture-dma: Phandle to a node for the DMA channel to use for |
| capture (recording) of audio. This is typically dictated |
| by SOC design. See the notes below. |
| - fsl,fifo-depth: The number of elements in the transmit and receive FIFOs. |
| This number is the maximum allowed value for SFCSR[TFWM0]. |
| - fsl,ssi-asynchronous: |
| If specified, the SSI is to be programmed in asynchronous |
| mode. In this mode, pins SRCK, STCK, SRFS, and STFS must |
| all be connected to valid signals. In synchronous mode, |
| SRCK and SRFS are ignored. Asynchronous mode allows |
| playback and capture to use different sample sizes and |
| sample rates. Some drivers may require that SRCK and STCK |
| be connected together, and SRFS and STFS be connected |
| together. This would still allow different sample sizes, |
| but not different sample rates. |
| |
| Required are also ac97 link bindings if ac97 is used. See |
| Documentation/devicetree/bindings/sound/soc-ac97link.txt for the necessary |
| bindings. |
| |
| Optional properties: |
| - codec-handle: Phandle to a 'codec' node that defines an audio |
| codec connected to this SSI. This node is typically |
| a child of an I2C or other control node. |
| - fsl,fiq-stream-filter: Bool property. Disabled DMA and use FIQ instead to |
| filter the codec stream. This is necessary for some boards |
| where an incompatible codec is connected to this SSI, e.g. |
| on pca100 and pcm043. |
| - dmas: Generic dma devicetree binding as described in |
| Documentation/devicetree/bindings/dma/dma.txt. |
| - dma-names: Two dmas have to be defined, "tx" and "rx", if fsl,imx-fiq |
| is not defined. |
| |
| Child 'codec' node required properties: |
| - compatible: Compatible list, contains the name of the codec |
| |
| Child 'codec' node optional properties: |
| - clock-frequency: The frequency of the input clock, which typically comes |
| from an on-board dedicated oscillator. |
| |
| Notes on fsl,playback-dma and fsl,capture-dma: |
| |
| On SOCs that have an SSI, specific DMA channels are hard-wired for playback |
| and capture. On the MPC8610, for example, SSI1 must use DMA channel 0 for |
| playback and DMA channel 1 for capture. SSI2 must use DMA channel 2 for |
| playback and DMA channel 3 for capture. The developer can choose which |
| DMA controller to use, but the channels themselves are hard-wired. The |
| purpose of these two properties is to represent this hardware design. |
| |
| The device tree nodes for the DMA channels that are referenced by |
| "fsl,playback-dma" and "fsl,capture-dma" must be marked as compatible with |
| "fsl,ssi-dma-channel". The SOC-specific compatible string (e.g. |
| "fsl,mpc8610-dma-channel") can remain. If these nodes are left as |
| "fsl,elo-dma-channel" or "fsl,eloplus-dma-channel", then the generic Elo DMA |
| drivers (fsldma) will attempt to use them, and it will conflict with the |
| sound drivers. |