| .text |
| #include <linux/linkage.h> |
| #include <asm/segment.h> |
| #include <asm/pgtable.h> |
| #include <asm/page.h> |
| #include <asm/msr.h> |
| |
| # Copyright 2003 Pavel Machek <pavel@suse.cz>, distribute under GPLv2 |
| # |
| # wakeup_code runs in real mode, and at unknown address (determined at run-time). |
| # Therefore it must only use relative jumps/calls. |
| # |
| # Do we need to deal with A20? It is okay: ACPI specs says A20 must be enabled |
| # |
| # If physical address of wakeup_code is 0x12345, BIOS should call us with |
| # cs = 0x1234, eip = 0x05 |
| # |
| |
| |
| ALIGN |
| .align 16 |
| ENTRY(wakeup_start) |
| wakeup_code: |
| wakeup_code_start = . |
| .code16 |
| |
| # Running in *copy* of this code, somewhere in low 1MB. |
| |
| movb $0xa1, %al ; outb %al, $0x80 |
| cli |
| cld |
| # setup data segment |
| movw %cs, %ax |
| movw %ax, %ds # Make ds:0 point to wakeup_start |
| movw %ax, %ss |
| # Private stack is needed for ASUS board |
| mov $(wakeup_stack - wakeup_code), %sp |
| |
| pushl $0 # Kill any dangerous flags |
| popfl |
| |
| movl real_magic - wakeup_code, %eax |
| cmpl $0x12345678, %eax |
| jne bogus_real_magic |
| |
| call verify_cpu # Verify the cpu supports long |
| # mode |
| testl %eax, %eax |
| jnz no_longmode |
| |
| testl $1, video_flags - wakeup_code |
| jz 1f |
| lcall $0xc000,$3 |
| movw %cs, %ax |
| movw %ax, %ds # Bios might have played with that |
| movw %ax, %ss |
| 1: |
| |
| testl $2, video_flags - wakeup_code |
| jz 1f |
| mov video_mode - wakeup_code, %ax |
| call mode_seta |
| 1: |
| |
| movw $0xb800, %ax |
| movw %ax,%fs |
| movw $0x0e00 + 'L', %fs:(0x10) |
| |
| movb $0xa2, %al ; outb %al, $0x80 |
| |
| mov %ds, %ax # Find 32bit wakeup_code addr |
| movzx %ax, %esi # (Convert %ds:gdt to a liner ptr) |
| shll $4, %esi |
| # Fix up the vectors |
| addl %esi, wakeup_32_vector - wakeup_code |
| addl %esi, wakeup_long64_vector - wakeup_code |
| addl %esi, gdt_48a + 2 - wakeup_code # Fixup the gdt pointer |
| |
| lidtl %ds:idt_48a - wakeup_code |
| lgdtl %ds:gdt_48a - wakeup_code # load gdt with whatever is |
| # appropriate |
| |
| movl $1, %eax # protected mode (PE) bit |
| lmsw %ax # This is it! |
| jmp 1f |
| 1: |
| |
| ljmpl *(wakeup_32_vector - wakeup_code) |
| |
| .balign 4 |
| wakeup_32_vector: |
| .long wakeup_32 - wakeup_code |
| .word __KERNEL32_CS, 0 |
| |
| .code32 |
| wakeup_32: |
| # Running in this code, but at low address; paging is not yet turned on. |
| movb $0xa5, %al ; outb %al, $0x80 |
| |
| movl $__KERNEL_DS, %eax |
| movl %eax, %ds |
| |
| movw $0x0e00 + 'i', %ds:(0xb8012) |
| movb $0xa8, %al ; outb %al, $0x80; |
| |
| /* |
| * Prepare for entering 64bits mode |
| */ |
| |
| /* Enable PAE */ |
| xorl %eax, %eax |
| btsl $5, %eax |
| movl %eax, %cr4 |
| |
| /* Setup early boot stage 4 level pagetables */ |
| leal (wakeup_level4_pgt - wakeup_code)(%esi), %eax |
| movl %eax, %cr3 |
| |
| /* Check if nx is implemented */ |
| movl $0x80000001, %eax |
| cpuid |
| movl %edx,%edi |
| |
| /* Enable Long Mode */ |
| xorl %eax, %eax |
| btsl $_EFER_LME, %eax |
| |
| /* No Execute supported? */ |
| btl $20,%edi |
| jnc 1f |
| btsl $_EFER_NX, %eax |
| |
| /* Make changes effective */ |
| 1: movl $MSR_EFER, %ecx |
| xorl %edx, %edx |
| wrmsr |
| |
| xorl %eax, %eax |
| btsl $31, %eax /* Enable paging and in turn activate Long Mode */ |
| btsl $0, %eax /* Enable protected mode */ |
| |
| /* Make changes effective */ |
| movl %eax, %cr0 |
| |
| /* At this point: |
| CR4.PAE must be 1 |
| CS.L must be 0 |
| CR3 must point to PML4 |
| Next instruction must be a branch |
| This must be on identity-mapped page |
| */ |
| /* |
| * At this point we're in long mode but in 32bit compatibility mode |
| * with EFER.LME = 1, CS.L = 0, CS.D = 1 (and in turn |
| * EFER.LMA = 1). Now we want to jump in 64bit mode, to do that we load |
| * the new gdt/idt that has __KERNEL_CS with CS.L = 1. |
| */ |
| |
| /* Finally jump in 64bit mode */ |
| ljmp *(wakeup_long64_vector - wakeup_code)(%esi) |
| |
| .balign 4 |
| wakeup_long64_vector: |
| .long wakeup_long64 - wakeup_code |
| .word __KERNEL_CS, 0 |
| |
| .code64 |
| |
| /* Hooray, we are in Long 64-bit mode (but still running in |
| * low memory) |
| */ |
| wakeup_long64: |
| /* |
| * We must switch to a new descriptor in kernel space for the GDT |
| * because soon the kernel won't have access anymore to the userspace |
| * addresses where we're currently running on. We have to do that here |
| * because in 32bit we couldn't load a 64bit linear address. |
| */ |
| lgdt cpu_gdt_descr |
| |
| movw $0x0e00 + 'n', %ds:(0xb8014) |
| movb $0xa9, %al ; outb %al, $0x80 |
| |
| movq saved_magic, %rax |
| movq $0x123456789abcdef0, %rdx |
| cmpq %rdx, %rax |
| jne bogus_64_magic |
| |
| movw $0x0e00 + 'u', %ds:(0xb8016) |
| |
| nop |
| nop |
| movw $__KERNEL_DS, %ax |
| movw %ax, %ss |
| movw %ax, %ds |
| movw %ax, %es |
| movw %ax, %fs |
| movw %ax, %gs |
| movq saved_rsp, %rsp |
| |
| movw $0x0e00 + 'x', %ds:(0xb8018) |
| movq saved_rbx, %rbx |
| movq saved_rdi, %rdi |
| movq saved_rsi, %rsi |
| movq saved_rbp, %rbp |
| |
| movw $0x0e00 + '!', %ds:(0xb801a) |
| movq saved_rip, %rax |
| jmp *%rax |
| |
| .code32 |
| |
| .align 64 |
| gdta: |
| /* Its good to keep gdt in sync with one in trampoline.S */ |
| .word 0, 0, 0, 0 # dummy |
| /* ??? Why I need the accessed bit set in order for this to work? */ |
| .quad 0x00cf9b000000ffff # __KERNEL32_CS |
| .quad 0x00af9b000000ffff # __KERNEL_CS |
| .quad 0x00cf93000000ffff # __KERNEL_DS |
| |
| idt_48a: |
| .word 0 # idt limit = 0 |
| .word 0, 0 # idt base = 0L |
| |
| gdt_48a: |
| .word 0x800 # gdt limit=2048, |
| # 256 GDT entries |
| .long gdta - wakeup_code # gdt base (relocated in later) |
| |
| real_magic: .quad 0 |
| video_mode: .quad 0 |
| video_flags: .quad 0 |
| |
| .code16 |
| bogus_real_magic: |
| movb $0xba,%al ; outb %al,$0x80 |
| jmp bogus_real_magic |
| |
| .code64 |
| bogus_64_magic: |
| movb $0xb3,%al ; outb %al,$0x80 |
| jmp bogus_64_magic |
| |
| .code16 |
| no_longmode: |
| movb $0xbc,%al ; outb %al,$0x80 |
| jmp no_longmode |
| |
| #include "../verify_cpu.S" |
| |
| /* This code uses an extended set of video mode numbers. These include: |
| * Aliases for standard modes |
| * NORMAL_VGA (-1) |
| * EXTENDED_VGA (-2) |
| * ASK_VGA (-3) |
| * Video modes numbered by menu position -- NOT RECOMMENDED because of lack |
| * of compatibility when extending the table. These are between 0x00 and 0xff. |
| */ |
| #define VIDEO_FIRST_MENU 0x0000 |
| |
| /* Standard BIOS video modes (BIOS number + 0x0100) */ |
| #define VIDEO_FIRST_BIOS 0x0100 |
| |
| /* VESA BIOS video modes (VESA number + 0x0200) */ |
| #define VIDEO_FIRST_VESA 0x0200 |
| |
| /* Video7 special modes (BIOS number + 0x0900) */ |
| #define VIDEO_FIRST_V7 0x0900 |
| |
| # Setting of user mode (AX=mode ID) => CF=success |
| .code16 |
| mode_seta: |
| movw %ax, %bx |
| #if 0 |
| cmpb $0xff, %ah |
| jz setalias |
| |
| testb $VIDEO_RECALC>>8, %ah |
| jnz _setrec |
| |
| cmpb $VIDEO_FIRST_RESOLUTION>>8, %ah |
| jnc setres |
| |
| cmpb $VIDEO_FIRST_SPECIAL>>8, %ah |
| jz setspc |
| |
| cmpb $VIDEO_FIRST_V7>>8, %ah |
| jz setv7 |
| #endif |
| |
| cmpb $VIDEO_FIRST_VESA>>8, %ah |
| jnc check_vesaa |
| #if 0 |
| orb %ah, %ah |
| jz setmenu |
| #endif |
| |
| decb %ah |
| # jz setbios Add bios modes later |
| |
| setbada: clc |
| ret |
| |
| check_vesaa: |
| subb $VIDEO_FIRST_VESA>>8, %bh |
| orw $0x4000, %bx # Use linear frame buffer |
| movw $0x4f02, %ax # VESA BIOS mode set call |
| int $0x10 |
| cmpw $0x004f, %ax # AL=4f if implemented |
| jnz _setbada # AH=0 if OK |
| |
| stc |
| ret |
| |
| _setbada: jmp setbada |
| |
| wakeup_stack_begin: # Stack grows down |
| |
| .org 0xff0 |
| wakeup_stack: # Just below end of page |
| |
| .org 0x1000 |
| ENTRY(wakeup_level4_pgt) |
| .quad level3_ident_pgt - __START_KERNEL_map + _KERNPG_TABLE |
| .fill 510,8,0 |
| /* (2^48-(2*1024*1024*1024))/(2^39) = 511 */ |
| .quad level3_kernel_pgt - __START_KERNEL_map + _KERNPG_TABLE |
| |
| ENTRY(wakeup_end) |
| |
| ## |
| # acpi_copy_wakeup_routine |
| # |
| # Copy the above routine to low memory. |
| # |
| # Parameters: |
| # %rdi: place to copy wakeup routine to |
| # |
| # Returned address is location of code in low memory (past data and stack) |
| # |
| .code64 |
| ENTRY(acpi_copy_wakeup_routine) |
| pushq %rax |
| pushq %rdx |
| |
| movl saved_video_mode, %edx |
| movl %edx, video_mode - wakeup_start (,%rdi) |
| movl acpi_video_flags, %edx |
| movl %edx, video_flags - wakeup_start (,%rdi) |
| movq $0x12345678, real_magic - wakeup_start (,%rdi) |
| movq $0x123456789abcdef0, %rdx |
| movq %rdx, saved_magic |
| |
| movq saved_magic, %rax |
| movq $0x123456789abcdef0, %rdx |
| cmpq %rdx, %rax |
| jne bogus_64_magic |
| |
| # restore the regs we used |
| popq %rdx |
| popq %rax |
| ENTRY(do_suspend_lowlevel_s4bios) |
| ret |
| |
| .align 2 |
| .p2align 4,,15 |
| .globl do_suspend_lowlevel |
| .type do_suspend_lowlevel,@function |
| do_suspend_lowlevel: |
| .LFB5: |
| subq $8, %rsp |
| xorl %eax, %eax |
| call save_processor_state |
| |
| movq %rsp, saved_context_esp(%rip) |
| movq %rax, saved_context_eax(%rip) |
| movq %rbx, saved_context_ebx(%rip) |
| movq %rcx, saved_context_ecx(%rip) |
| movq %rdx, saved_context_edx(%rip) |
| movq %rbp, saved_context_ebp(%rip) |
| movq %rsi, saved_context_esi(%rip) |
| movq %rdi, saved_context_edi(%rip) |
| movq %r8, saved_context_r08(%rip) |
| movq %r9, saved_context_r09(%rip) |
| movq %r10, saved_context_r10(%rip) |
| movq %r11, saved_context_r11(%rip) |
| movq %r12, saved_context_r12(%rip) |
| movq %r13, saved_context_r13(%rip) |
| movq %r14, saved_context_r14(%rip) |
| movq %r15, saved_context_r15(%rip) |
| pushfq ; popq saved_context_eflags(%rip) |
| |
| movq $.L97, saved_rip(%rip) |
| |
| movq %rsp,saved_rsp |
| movq %rbp,saved_rbp |
| movq %rbx,saved_rbx |
| movq %rdi,saved_rdi |
| movq %rsi,saved_rsi |
| |
| addq $8, %rsp |
| movl $3, %edi |
| xorl %eax, %eax |
| jmp acpi_enter_sleep_state |
| .L97: |
| .p2align 4,,7 |
| .L99: |
| .align 4 |
| movl $24, %eax |
| movw %ax, %ds |
| movq saved_context+58(%rip), %rax |
| movq %rax, %cr4 |
| movq saved_context+50(%rip), %rax |
| movq %rax, %cr3 |
| movq saved_context+42(%rip), %rax |
| movq %rax, %cr2 |
| movq saved_context+34(%rip), %rax |
| movq %rax, %cr0 |
| pushq saved_context_eflags(%rip) ; popfq |
| movq saved_context_esp(%rip), %rsp |
| movq saved_context_ebp(%rip), %rbp |
| movq saved_context_eax(%rip), %rax |
| movq saved_context_ebx(%rip), %rbx |
| movq saved_context_ecx(%rip), %rcx |
| movq saved_context_edx(%rip), %rdx |
| movq saved_context_esi(%rip), %rsi |
| movq saved_context_edi(%rip), %rdi |
| movq saved_context_r08(%rip), %r8 |
| movq saved_context_r09(%rip), %r9 |
| movq saved_context_r10(%rip), %r10 |
| movq saved_context_r11(%rip), %r11 |
| movq saved_context_r12(%rip), %r12 |
| movq saved_context_r13(%rip), %r13 |
| movq saved_context_r14(%rip), %r14 |
| movq saved_context_r15(%rip), %r15 |
| |
| xorl %eax, %eax |
| addq $8, %rsp |
| jmp restore_processor_state |
| .LFE5: |
| .Lfe5: |
| .size do_suspend_lowlevel,.Lfe5-do_suspend_lowlevel |
| |
| .data |
| ALIGN |
| ENTRY(saved_rbp) .quad 0 |
| ENTRY(saved_rsi) .quad 0 |
| ENTRY(saved_rdi) .quad 0 |
| ENTRY(saved_rbx) .quad 0 |
| |
| ENTRY(saved_rip) .quad 0 |
| ENTRY(saved_rsp) .quad 0 |
| |
| ENTRY(saved_magic) .quad 0 |