arch/avr32/boards/atngw100/setup.c - LeafOS-Devices/android_kernel_samsung_gta4xl - Gitiles

 /*
  * Board-specific setup code for the ATNGW100 Network Gateway
  *
  * Copyright (C) 2005-2006 Atmel Corporation
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
 #include <linux/clk.h>
 #include <linux/etherdevice.h>
 #include <linux/gpio.h>
 #include <linux/irq.h>
 #include <linux/i2c.h>
 #include <linux/i2c-gpio.h>
 #include <linux/init.h>
 #include <linux/linkage.h>
 #include <linux/platform_device.h>
 #include <linux/types.h>
 #include <linux/leds.h>
 #include <linux/spi/spi.h>
 #include <linux/atmel-mci.h>
 #include <linux/usb/atmel_usba_udc.h>

 #include <asm/io.h>
 #include <asm/setup.h>

 #include <mach/at32ap700x.h>
 #include <mach/board.h>
 #include <mach/init.h>
 #include <mach/portmux.h>

 /* Oscillator frequencies. These are board-specific */
 unsigned long at32_board_osc_rates[3] = {
 	[0] = 32768,	/* 32.768 kHz on RTC osc */
 	[1] = 20000000,	/* 20 MHz on osc0 */
 	[2] = 12000000,	/* 12 MHz on osc1 */
 };

 /*
  * The ATNGW100 mkII is very similar to the ATNGW100. Both have the AT32AP7000
  * chip on board; the difference is that the ATNGW100 mkII has 128 MB 32-bit
  * SDRAM (the ATNGW100 has 32 MB 16-bit SDRAM) and 256 MB 16-bit NAND flash
  * (the ATNGW100 has none.)
  *
  * The RAM difference is handled by the boot loader, so the only difference we
  * end up handling here is the NAND flash, EBI pin reservation and if LCDC or
  * MACB1 should be enabled.
  */
 #ifdef CONFIG_BOARD_ATNGW100_MKII
 #include <linux/mtd/partitions.h>
 #include <mach/smc.h>

 static struct smc_timing nand_timing __initdata = {
 	.ncs_read_setup		= 0,
 	.nrd_setup		= 10,
 	.ncs_write_setup	= 0,
 	.nwe_setup		= 10,

 	.ncs_read_pulse		= 30,
 	.nrd_pulse		= 15,
 	.ncs_write_pulse	= 30,
 	.nwe_pulse		= 15,

 	.read_cycle		= 30,
 	.write_cycle		= 30,

 	.ncs_read_recover	= 0,
 	.nrd_recover		= 15,
 	.ncs_write_recover	= 0,
 	/* WE# high -> RE# low min 60 ns */
 	.nwe_recover		= 50,
 };

 static struct smc_config nand_config __initdata = {
 	.bus_width		= 2,
 	.nrd_controlled		= 1,
 	.nwe_controlled		= 1,
 	.nwait_mode		= 0,
 	.byte_write		= 0,
 	.tdf_cycles		= 2,
 	.tdf_mode		= 0,
 };

 static struct mtd_partition nand_partitions[] = {
 	{
 		.name		= "main",
 		.offset		= 0x00000000,
 		.size		= MTDPART_SIZ_FULL,
 	},
 };

 static struct mtd_partition *nand_part_info(int size, int *num_partitions)
 {
 	*num_partitions = ARRAY_SIZE(nand_partitions);
 	return nand_partitions;
 }

 static struct atmel_nand_data atngw100mkii_nand_data __initdata = {
 	.cle		= 21,
 	.ale		= 22,
 	.rdy_pin	= GPIO_PIN_PB(28),
 	.enable_pin	= GPIO_PIN_PE(23),
 	.bus_width_16	= true,
 	.partition_info	= nand_part_info,
 };
 #endif

 /* Initialized by bootloader-specific startup code. */
 struct tag *bootloader_tags __initdata;

 struct eth_addr {
 	u8 addr[6];
 };
 static struct eth_addr __initdata hw_addr[2];
 static struct eth_platform_data __initdata eth_data[2];

 static struct spi_board_info spi0_board_info[] __initdata = {
 	{
 		.modalias	= "mtd_dataflash",
 		.max_speed_hz	= 8000000,
 		.chip_select	= 0,
 	},
 };

 static struct mci_platform_data __initdata mci0_data = {
 	.slot[0] = {
 		.bus_width	= 4,
 #if defined(CONFIG_BOARD_ATNGW100_MKII)
 		.detect_pin	= GPIO_PIN_PC(25),
 		.wp_pin		= GPIO_PIN_PE(22),
 #else
 		.detect_pin	= GPIO_PIN_PC(25),
 		.wp_pin		= GPIO_PIN_PE(0),
 #endif
 	},
 };

 static struct usba_platform_data atngw100_usba_data __initdata = {
 #if defined(CONFIG_BOARD_ATNGW100_MKII)
 	.vbus_pin	= GPIO_PIN_PE(26),
 #else
 	.vbus_pin	= -ENODEV,
 #endif
 };

 /*
  * The next two functions should go away as the boot loader is
  * supposed to initialize the macb address registers with a valid
  * ethernet address. But we need to keep it around for a while until
  * we can be reasonably sure the boot loader does this.
  *
  * The phy_id is ignored as the driver will probe for it.
  */
 static int __init parse_tag_ethernet(struct tag *tag)
 {
 	int i;

 	i = tag->u.ethernet.mac_index;
 	if (i < ARRAY_SIZE(hw_addr))
 		memcpy(hw_addr[i].addr, tag->u.ethernet.hw_address,
 		       sizeof(hw_addr[i].addr));

 	return 0;
 }
 __tagtable(ATAG_ETHERNET, parse_tag_ethernet);

 static void __init set_hw_addr(struct platform_device *pdev)
 {
 	struct resource *res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	const u8 *addr;
 	void __iomem *regs;
 	struct clk *pclk;

 	if (!res)
 		return;
 	if (pdev->id >= ARRAY_SIZE(hw_addr))
 		return;

 	addr = hw_addr[pdev->id].addr;
 	if (!is_valid_ether_addr(addr))
 		return;

 	/*
 	 * Since this is board-specific code, we'll cheat and use the
 	 * physical address directly as we happen to know that it's
 	 * the same as the virtual address.
 	 */
 	regs = (void __iomem __force *)res->start;
 	pclk = clk_get(&pdev->dev, "pclk");
 	if (!pclk)
 		return;

 	clk_enable(pclk);
 	__raw_writel((addr[3] << 24) | (addr[2] << 16)
 		     | (addr[1] << 8) | addr[0], regs + 0x98);
 	__raw_writel((addr[5] << 8) | addr[4], regs + 0x9c);
 	clk_disable(pclk);
 	clk_put(pclk);
 }

 void __init setup_board(void)
 {
 	at32_map_usart(1, 0, 0);	/* USART 1: /dev/ttyS0, DB9 */
 	at32_setup_serial_console(0);
 }

 static const struct gpio_led ngw_leds[] = {
 	{ .name = "sys", .gpio = GPIO_PIN_PA(16), .active_low = 1,
 		.default_trigger = "heartbeat",
 	},
 	{ .name = "a", .gpio = GPIO_PIN_PA(19), .active_low = 1, },
 	{ .name = "b", .gpio = GPIO_PIN_PE(19), .active_low = 1, },
 };

 static const struct gpio_led_platform_data ngw_led_data = {
 	.num_leds =	ARRAY_SIZE(ngw_leds),
 	.leds =		(void *) ngw_leds,
 };

 static struct platform_device ngw_gpio_leds = {
 	.name =		"leds-gpio",
 	.id =		-1,
 	.dev = {
 		.platform_data = (void *) &ngw_led_data,
 	}
 };

 static struct i2c_gpio_platform_data i2c_gpio_data = {
 	.sda_pin		= GPIO_PIN_PA(6),
 	.scl_pin		= GPIO_PIN_PA(7),
 	.sda_is_open_drain	= 1,
 	.scl_is_open_drain	= 1,
 	.udelay			= 2,	/* close to 100 kHz */
 };

 static struct platform_device i2c_gpio_device = {
 	.name		= "i2c-gpio",
 	.id		= 0,
 	.dev		= {
 		.platform_data	= &i2c_gpio_data,
 	},
 };

 static struct i2c_board_info __initdata i2c_info[] = {
 	/* NOTE:  original ATtiny24 firmware is at address 0x0b */
 };

 static int __init atngw100_init(void)
 {
 	unsigned	i;

 	/*
 	 * ATNGW100 mkII uses 32-bit SDRAM interface. Reserve the
 	 * SDRAM-specific pins so that nobody messes with them.
 	 */
 #ifdef CONFIG_BOARD_ATNGW100_MKII
 	at32_reserve_pin(GPIO_PIOE_BASE, ATMEL_EBI_PE_DATA_ALL);

 	smc_set_timing(&nand_config, &nand_timing);
 	smc_set_configuration(3, &nand_config);
 	at32_add_device_nand(0, &atngw100mkii_nand_data);
 #endif

 	at32_add_device_usart(0);

 	set_hw_addr(at32_add_device_eth(0, &eth_data[0]));
 #ifndef CONFIG_BOARD_ATNGW100_MKII_LCD
 	set_hw_addr(at32_add_device_eth(1, &eth_data[1]));
 #endif

 	at32_add_device_spi(0, spi0_board_info, ARRAY_SIZE(spi0_board_info));
 	at32_add_device_mci(0, &mci0_data);
 	at32_add_device_usba(0, &atngw100_usba_data);

 	for (i = 0; i < ARRAY_SIZE(ngw_leds); i++) {
 		at32_select_gpio(ngw_leds[i].gpio,
 				AT32_GPIOF_OUTPUT | AT32_GPIOF_HIGH);
 	}
 	platform_device_register(&ngw_gpio_leds);

 	/* all these i2c/smbus pins should have external pullups for
 	 * open-drain sharing among all I2C devices.  SDA and SCL do;
 	 * PB28/EXTINT3 (ATNGW100) and PE21 (ATNGW100 mkII) doesn't; it should
 	 * be SMBALERT# (for PMBus), but it's not available off-board.
 	 */
 #ifdef CONFIG_BOARD_ATNGW100_MKII
 	at32_select_periph(GPIO_PIOE_BASE, 1 << 21, 0, AT32_GPIOF_PULLUP);
 #else
 	at32_select_periph(GPIO_PIOB_BASE, 1 << 28, 0, AT32_GPIOF_PULLUP);
 #endif
 	at32_select_gpio(i2c_gpio_data.sda_pin,
 		AT32_GPIOF_MULTIDRV | AT32_GPIOF_OUTPUT | AT32_GPIOF_HIGH);
 	at32_select_gpio(i2c_gpio_data.scl_pin,
 		AT32_GPIOF_MULTIDRV | AT32_GPIOF_OUTPUT | AT32_GPIOF_HIGH);
 	platform_device_register(&i2c_gpio_device);
 	i2c_register_board_info(0, i2c_info, ARRAY_SIZE(i2c_info));

 	return 0;
 }
 postcore_initcall(atngw100_init);

 static int __init atngw100_arch_init(void)
 {
 	/* PB30 (ATNGW100) and PE30 (ATNGW100 mkII) is the otherwise unused
 	 * jumper on the mainboard, with an external pullup; the jumper grounds
 	 * it. Use it however you like, including letting U-Boot or Linux tweak
 	 * boot sequences.
 	 */
 #ifdef CONFIG_BOARD_ATNGW100_MKII
 	at32_select_gpio(GPIO_PIN_PE(30), 0);
 	gpio_request(GPIO_PIN_PE(30), "j15");
 	gpio_direction_input(GPIO_PIN_PE(30));
 	gpio_export(GPIO_PIN_PE(30), false);
 #else
 	at32_select_gpio(GPIO_PIN_PB(30), 0);
 	gpio_request(GPIO_PIN_PB(30), "j15");
 	gpio_direction_input(GPIO_PIN_PB(30));
 	gpio_export(GPIO_PIN_PB(30), false);
 #endif

 	/* set_irq_type() after the arch_initcall for EIC has run, and
 	 * before the I2C subsystem could try using this IRQ.
 	 */
 	return set_irq_type(AT32_EXTINT(3), IRQ_TYPE_EDGE_FALLING);
 }
 arch_initcall(atngw100_arch_init);
	/*
	* Board-specific setup code for the ATNGW100 Network Gateway
	*
	* Copyright (C) 2005-2006 Atmel Corporation
	*
	* This program is free software; you can redistribute it and/or modify
	* it under the terms of the GNU General Public License version 2 as
	* published by the Free Software Foundation.
	*/
	#include <linux/clk.h>
	#include <linux/etherdevice.h>
	#include <linux/gpio.h>
	#include <linux/irq.h>
	#include <linux/i2c.h>
	#include <linux/i2c-gpio.h>
	#include <linux/init.h>
	#include <linux/linkage.h>
	#include <linux/platform_device.h>
	#include <linux/types.h>
	#include <linux/leds.h>
	#include <linux/spi/spi.h>
	#include <linux/atmel-mci.h>
	#include <linux/usb/atmel_usba_udc.h>

	#include <asm/io.h>
	#include <asm/setup.h>

	#include <mach/at32ap700x.h>
	#include <mach/board.h>
	#include <mach/init.h>
	#include <mach/portmux.h>

	/* Oscillator frequencies. These are board-specific */
	unsigned long at32_board_osc_rates[3] = {
	[0] = 32768, /* 32.768 kHz on RTC osc */
	[1] = 20000000, /* 20 MHz on osc0 */
	[2] = 12000000, /* 12 MHz on osc1 */
	};

	/*
	* The ATNGW100 mkII is very similar to the ATNGW100. Both have the AT32AP7000
	* chip on board; the difference is that the ATNGW100 mkII has 128 MB 32-bit
	* SDRAM (the ATNGW100 has 32 MB 16-bit SDRAM) and 256 MB 16-bit NAND flash
	* (the ATNGW100 has none.)
	*
	* The RAM difference is handled by the boot loader, so the only difference we
	* end up handling here is the NAND flash, EBI pin reservation and if LCDC or
	* MACB1 should be enabled.
	*/
	#ifdef CONFIG_BOARD_ATNGW100_MKII
	#include <linux/mtd/partitions.h>
	#include <mach/smc.h>

	static struct smc_timing nand_timing __initdata = {
	.ncs_read_setup = 0,
	.nrd_setup = 10,
	.ncs_write_setup = 0,
	.nwe_setup = 10,

	.ncs_read_pulse = 30,
	.nrd_pulse = 15,
	.ncs_write_pulse = 30,
	.nwe_pulse = 15,

	.read_cycle = 30,
	.write_cycle = 30,

	.ncs_read_recover = 0,
	.nrd_recover = 15,
	.ncs_write_recover = 0,
	/* WE# high -> RE# low min 60 ns */
	.nwe_recover = 50,
	};

	static struct smc_config nand_config __initdata = {
	.bus_width = 2,
	.nrd_controlled = 1,
	.nwe_controlled = 1,
	.nwait_mode = 0,
	.byte_write = 0,
	.tdf_cycles = 2,
	.tdf_mode = 0,
	};

	static struct mtd_partition nand_partitions[] = {
	{
	.name = "main",
	.offset = 0x00000000,
	.size = MTDPART_SIZ_FULL,
	},
	};

	static struct mtd_partition nand_part_info(int size, int num_partitions)
	{
	*num_partitions = ARRAY_SIZE(nand_partitions);
	return nand_partitions;
	}

	static struct atmel_nand_data atngw100mkii_nand_data __initdata = {
	.cle = 21,
	.ale = 22,
	.rdy_pin = GPIO_PIN_PB(28),
	.enable_pin = GPIO_PIN_PE(23),
	.bus_width_16 = true,
	.partition_info = nand_part_info,
	};
	#endif

	/* Initialized by bootloader-specific startup code. */
	struct tag *bootloader_tags __initdata;

	struct eth_addr {
	u8 addr[6];
	};
	static struct eth_addr __initdata hw_addr[2];
	static struct eth_platform_data __initdata eth_data[2];

	static struct spi_board_info spi0_board_info[] __initdata = {
	{
	.modalias = "mtd_dataflash",
	.max_speed_hz = 8000000,
	.chip_select = 0,
	},
	};

	static struct mci_platform_data __initdata mci0_data = {
	.slot[0] = {
	.bus_width = 4,
	#if defined(CONFIG_BOARD_ATNGW100_MKII)
	.detect_pin = GPIO_PIN_PC(25),
	.wp_pin = GPIO_PIN_PE(22),
	#else
	.detect_pin = GPIO_PIN_PC(25),
	.wp_pin = GPIO_PIN_PE(0),
	#endif
	},
	};

	static struct usba_platform_data atngw100_usba_data __initdata = {
	#if defined(CONFIG_BOARD_ATNGW100_MKII)
	.vbus_pin = GPIO_PIN_PE(26),
	#else
	.vbus_pin = -ENODEV,
	#endif
	};

	/*
	* The next two functions should go away as the boot loader is
	* supposed to initialize the macb address registers with a valid
	* ethernet address. But we need to keep it around for a while until
	* we can be reasonably sure the boot loader does this.
	*
	* The phy_id is ignored as the driver will probe for it.
	*/
	static int __init parse_tag_ethernet(struct tag *tag)
	{
	int i;

	i = tag->u.ethernet.mac_index;
	if (i < ARRAY_SIZE(hw_addr))
	memcpy(hw_addr[i].addr, tag->u.ethernet.hw_address,
	sizeof(hw_addr[i].addr));

	return 0;
	}
	__tagtable(ATAG_ETHERNET, parse_tag_ethernet);

	static void __init set_hw_addr(struct platform_device *pdev)
	{
	struct resource *res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
	const u8 *addr;
	void __iomem *regs;
	struct clk *pclk;

	if (!res)
	return;
	if (pdev->id >= ARRAY_SIZE(hw_addr))
	return;

	addr = hw_addr[pdev->id].addr;
	if (!is_valid_ether_addr(addr))
	return;

	/*
	* Since this is board-specific code, we'll cheat and use the
	* physical address directly as we happen to know that it's
	* the same as the virtual address.
	*/
	regs = (void __iomem __force *)res->start;
	pclk = clk_get(&pdev->dev, "pclk");
	if (!pclk)
	return;

	clk_enable(pclk);
	__raw_writel((addr[3] << 24) \| (addr[2] << 16)
	\| (addr[1] << 8) \| addr[0], regs + 0x98);
	__raw_writel((addr[5] << 8) \| addr[4], regs + 0x9c);
	clk_disable(pclk);
	clk_put(pclk);
	}

	void __init setup_board(void)
	{
	at32_map_usart(1, 0, 0); /* USART 1: /dev/ttyS0, DB9 */
	at32_setup_serial_console(0);
	}

	static const struct gpio_led ngw_leds[] = {
	{ .name = "sys", .gpio = GPIO_PIN_PA(16), .active_low = 1,
	.default_trigger = "heartbeat",
	},
	{ .name = "a", .gpio = GPIO_PIN_PA(19), .active_low = 1, },
	{ .name = "b", .gpio = GPIO_PIN_PE(19), .active_low = 1, },
	};

	static const struct gpio_led_platform_data ngw_led_data = {
	.num_leds = ARRAY_SIZE(ngw_leds),
	.leds = (void *) ngw_leds,
	};

	static struct platform_device ngw_gpio_leds = {
	.name = "leds-gpio",
	.id = -1,
	.dev = {
	.platform_data = (void *) &ngw_led_data,
	}
	};

	static struct i2c_gpio_platform_data i2c_gpio_data = {
	.sda_pin = GPIO_PIN_PA(6),
	.scl_pin = GPIO_PIN_PA(7),
	.sda_is_open_drain = 1,
	.scl_is_open_drain = 1,
	.udelay = 2, /* close to 100 kHz */
	};

	static struct platform_device i2c_gpio_device = {
	.name = "i2c-gpio",
	.id = 0,
	.dev = {
	.platform_data = &i2c_gpio_data,
	},
	};

	static struct i2c_board_info __initdata i2c_info[] = {
	/* NOTE: original ATtiny24 firmware is at address 0x0b */
	};

	static int __init atngw100_init(void)
	{
	unsigned i;

	/*
	* ATNGW100 mkII uses 32-bit SDRAM interface. Reserve the
	* SDRAM-specific pins so that nobody messes with them.
	*/
	#ifdef CONFIG_BOARD_ATNGW100_MKII
	at32_reserve_pin(GPIO_PIOE_BASE, ATMEL_EBI_PE_DATA_ALL);

	smc_set_timing(&nand_config, &nand_timing);
	smc_set_configuration(3, &nand_config);
	at32_add_device_nand(0, &atngw100mkii_nand_data);
	#endif

	at32_add_device_usart(0);

	set_hw_addr(at32_add_device_eth(0, &eth_data[0]));
	#ifndef CONFIG_BOARD_ATNGW100_MKII_LCD
	set_hw_addr(at32_add_device_eth(1, &eth_data[1]));
	#endif

	at32_add_device_spi(0, spi0_board_info, ARRAY_SIZE(spi0_board_info));
	at32_add_device_mci(0, &mci0_data);
	at32_add_device_usba(0, &atngw100_usba_data);

	for (i = 0; i < ARRAY_SIZE(ngw_leds); i++) {
	at32_select_gpio(ngw_leds[i].gpio,
	AT32_GPIOF_OUTPUT \| AT32_GPIOF_HIGH);
	}
	platform_device_register(&ngw_gpio_leds);

	/* all these i2c/smbus pins should have external pullups for
	* open-drain sharing among all I2C devices. SDA and SCL do;
	* PB28/EXTINT3 (ATNGW100) and PE21 (ATNGW100 mkII) doesn't; it should
	* be SMBALERT# (for PMBus), but it's not available off-board.
	*/
	#ifdef CONFIG_BOARD_ATNGW100_MKII
	at32_select_periph(GPIO_PIOE_BASE, 1 << 21, 0, AT32_GPIOF_PULLUP);
	#else
	at32_select_periph(GPIO_PIOB_BASE, 1 << 28, 0, AT32_GPIOF_PULLUP);
	#endif
	at32_select_gpio(i2c_gpio_data.sda_pin,
	AT32_GPIOF_MULTIDRV \| AT32_GPIOF_OUTPUT \| AT32_GPIOF_HIGH);
	at32_select_gpio(i2c_gpio_data.scl_pin,
	AT32_GPIOF_MULTIDRV \| AT32_GPIOF_OUTPUT \| AT32_GPIOF_HIGH);
	platform_device_register(&i2c_gpio_device);
	i2c_register_board_info(0, i2c_info, ARRAY_SIZE(i2c_info));

	return 0;
	}
	postcore_initcall(atngw100_init);

	static int __init atngw100_arch_init(void)
	{
	/* PB30 (ATNGW100) and PE30 (ATNGW100 mkII) is the otherwise unused
	* jumper on the mainboard, with an external pullup; the jumper grounds
	* it. Use it however you like, including letting U-Boot or Linux tweak
	* boot sequences.
	*/
	#ifdef CONFIG_BOARD_ATNGW100_MKII
	at32_select_gpio(GPIO_PIN_PE(30), 0);
	gpio_request(GPIO_PIN_PE(30), "j15");
	gpio_direction_input(GPIO_PIN_PE(30));
	gpio_export(GPIO_PIN_PE(30), false);
	#else
	at32_select_gpio(GPIO_PIN_PB(30), 0);
	gpio_request(GPIO_PIN_PB(30), "j15");
	gpio_direction_input(GPIO_PIN_PB(30));
	gpio_export(GPIO_PIN_PB(30), false);
	#endif

	/* set_irq_type() after the arch_initcall for EIC has run, and
	* before the I2C subsystem could try using this IRQ.
	*/
	return set_irq_type(AT32_EXTINT(3), IRQ_TYPE_EDGE_FALLING);
	}
	arch_initcall(atngw100_arch_init);