| BATMAN-ADV |
| ---------- |
| |
| Batman advanced is a new approach to wireless networking which |
| does no longer operate on the IP basis. Unlike the batman daemon, |
| which exchanges information using UDP packets and sets routing |
| tables, batman-advanced operates on ISO/OSI Layer 2 only and uses |
| and routes (or better: bridges) Ethernet Frames. It emulates a |
| virtual network switch of all nodes participating. Therefore all |
| nodes appear to be link local, thus all higher operating proto- |
| cols won't be affected by any changes within the network. You can |
| run almost any protocol above batman advanced, prominent examples |
| are: IPv4, IPv6, DHCP, IPX. |
| |
| Batman advanced was implemented as a Linux kernel driver to re- |
| duce the overhead to a minimum. It does not depend on any (other) |
| network driver, and can be used on wifi as well as ethernet lan, |
| vpn, etc ... (anything with ethernet-style layer 2). |
| |
| |
| CONFIGURATION |
| ------------- |
| |
| Load the batman-adv module into your kernel: |
| |
| # insmod batman-adv.ko |
| |
| The module is now waiting for activation. You must add some in- |
| terfaces on which batman can operate. After loading the module |
| batman advanced will scan your systems interfaces to search for |
| compatible interfaces. Once found, it will create subfolders in |
| the /sys directories of each supported interface, e.g. |
| |
| # ls /sys/class/net/eth0/batman_adv/ |
| # iface_status mesh_iface |
| |
| If an interface does not have the "batman_adv" subfolder it prob- |
| ably is not supported. Not supported interfaces are: loopback, |
| non-ethernet and batman's own interfaces. |
| |
| Note: After the module was loaded it will continuously watch for |
| new interfaces to verify the compatibility. There is no need to |
| reload the module if you plug your USB wifi adapter into your ma- |
| chine after batman advanced was initially loaded. |
| |
| To activate a given interface simply write "bat0" into its |
| "mesh_iface" file inside the batman_adv subfolder: |
| |
| # echo bat0 > /sys/class/net/eth0/batman_adv/mesh_iface |
| |
| Repeat this step for all interfaces you wish to add. Now batman |
| starts using/broadcasting on this/these interface(s). |
| |
| By reading the "iface_status" file you can check its status: |
| |
| # cat /sys/class/net/eth0/batman_adv/iface_status |
| # active |
| |
| To deactivate an interface you have to write "none" into its |
| "mesh_iface" file: |
| |
| # echo none > /sys/class/net/eth0/batman_adv/mesh_iface |
| |
| |
| All mesh wide settings can be found in batman's own interface |
| folder: |
| |
| # ls /sys/class/net/bat0/mesh/ |
| #aggregated_ogms distributed_arp_table gw_sel_class orig_interval |
| #ap_isolation fragmentation hop_penalty routing_algo |
| #bonding gw_bandwidth isolation_mark vlan0 |
| #bridge_loop_avoidance gw_mode log_level |
| |
| There is a special folder for debugging information: |
| |
| # ls /sys/kernel/debug/batman_adv/bat0/ |
| # bla_backbone_table log transtable_global |
| # bla_claim_table originators transtable_local |
| # gateways socket |
| |
| Some of the files contain all sort of status information regard- |
| ing the mesh network. For example, you can view the table of |
| originators (mesh participants) with: |
| |
| # cat /sys/kernel/debug/batman_adv/bat0/originators |
| |
| Other files allow to change batman's behaviour to better fit your |
| requirements. For instance, you can check the current originator |
| interval (value in milliseconds which determines how often batman |
| sends its broadcast packets): |
| |
| # cat /sys/class/net/bat0/mesh/orig_interval |
| # 1000 |
| |
| and also change its value: |
| |
| # echo 3000 > /sys/class/net/bat0/mesh/orig_interval |
| |
| In very mobile scenarios, you might want to adjust the originator |
| interval to a lower value. This will make the mesh more respon- |
| sive to topology changes, but will also increase the overhead. |
| |
| |
| USAGE |
| ----- |
| |
| To make use of your newly created mesh, batman advanced provides |
| a new interface "bat0" which you should use from this point on. |
| All interfaces added to batman advanced are not relevant any |
| longer because batman handles them for you. Basically, one "hands |
| over" the data by using the batman interface and batman will make |
| sure it reaches its destination. |
| |
| The "bat0" interface can be used like any other regular inter- |
| face. It needs an IP address which can be either statically con- |
| figured or dynamically (by using DHCP or similar services): |
| |
| # NodeA: ip link set up dev bat0 |
| # NodeA: ip addr add 192.168.0.1/24 dev bat0 |
| |
| # NodeB: ip link set up dev bat0 |
| # NodeB: ip addr add 192.168.0.2/24 dev bat0 |
| # NodeB: ping 192.168.0.1 |
| |
| Note: In order to avoid problems remove all IP addresses previ- |
| ously assigned to interfaces now used by batman advanced, e.g. |
| |
| # ip addr flush dev eth0 |
| |
| |
| LOGGING/DEBUGGING |
| ----------------- |
| |
| All error messages, warnings and information messages are sent to |
| the kernel log. Depending on your operating system distribution |
| this can be read in one of a number of ways. Try using the com- |
| mands: dmesg, logread, or looking in the files /var/log/kern.log |
| or /var/log/syslog. All batman-adv messages are prefixed with |
| "batman-adv:" So to see just these messages try |
| |
| # dmesg | grep batman-adv |
| |
| When investigating problems with your mesh network it is some- |
| times necessary to see more detail debug messages. This must be |
| enabled when compiling the batman-adv module. When building bat- |
| man-adv as part of kernel, use "make menuconfig" and enable the |
| option "B.A.T.M.A.N. debugging". |
| |
| Those additional debug messages can be accessed using a special |
| file in debugfs |
| |
| # cat /sys/kernel/debug/batman_adv/bat0/log |
| |
| The additional debug output is by default disabled. It can be en- |
| abled during run time. Following log_levels are defined: |
| |
| 0 - All debug output disabled |
| 1 - Enable messages related to routing / flooding / broadcasting |
| 2 - Enable messages related to route added / changed / deleted |
| 4 - Enable messages related to translation table operations |
| 8 - Enable messages related to bridge loop avoidance |
| 16 - Enable messaged related to DAT, ARP snooping and parsing |
| 31 - Enable all messages |
| |
| The debug output can be changed at runtime using the file |
| /sys/class/net/bat0/mesh/log_level. e.g. |
| |
| # echo 6 > /sys/class/net/bat0/mesh/log_level |
| |
| will enable debug messages for when routes change. |
| |
| Counters for different types of packets entering and leaving the |
| batman-adv module are available through ethtool: |
| |
| # ethtool --statistics bat0 |
| |
| |
| BATCTL |
| ------ |
| |
| As batman advanced operates on layer 2 all hosts participating in |
| the virtual switch are completely transparent for all protocols |
| above layer 2. Therefore the common diagnosis tools do not work |
| as expected. To overcome these problems batctl was created. At |
| the moment the batctl contains ping, traceroute, tcpdump and |
| interfaces to the kernel module settings. |
| |
| For more information, please see the manpage (man batctl). |
| |
| batctl is available on http://www.open-mesh.org/ |
| |
| |
| CONTACT |
| ------- |
| |
| Please send us comments, experiences, questions, anything :) |
| |
| IRC: #batman on irc.freenode.org |
| Mailing-list: b.a.t.m.a.n@open-mesh.org (optional subscription |
| at https://lists.open-mesh.org/mm/listinfo/b.a.t.m.a.n) |
| |
| You can also contact the Authors: |
| |
| Marek Lindner <mareklindner@neomailbox.ch> |
| Simon Wunderlich <sw@simonwunderlich.de> |