| .. -*- coding: utf-8; mode: rst -*- |
| |
| .. _FE_READ_STATUS: |
| |
| ******************** |
| ioctl FE_READ_STATUS |
| ******************** |
| |
| Name |
| ==== |
| |
| FE_READ_STATUS - Returns status information about the front-end. This call only requires - read-only access to the device |
| |
| |
| Synopsis |
| ======== |
| |
| .. cpp:function:: int ioctl( int fd, int request, unsigned int *status ) |
| |
| |
| Arguments |
| ========= |
| |
| ``fd`` |
| File descriptor returned by :ref:`open() <frontend_f_open>`. |
| |
| ``request`` |
| FE_READ_STATUS |
| |
| ``status`` |
| pointer to a bitmask integer filled with the values defined by enum |
| :ref:`fe_status <fe-status>`. |
| |
| |
| Description |
| =========== |
| |
| All DVB frontend devices support the ``FE_READ_STATUS`` ioctl. It is |
| used to check about the locking status of the frontend after being |
| tuned. The ioctl takes a pointer to an integer where the status will be |
| written. |
| |
| .. note:: The size of status is actually sizeof(enum fe_status), with |
| varies according with the architecture. This needs to be fixed in the |
| future. |
| |
| |
| .. _fe-status-t: |
| |
| int fe_status |
| ============= |
| |
| The fe_status parameter is used to indicate the current state and/or |
| state changes of the frontend hardware. It is produced using the enum |
| :ref:`fe_status <fe-status>` values on a bitmask |
| |
| |
| .. _fe-status: |
| |
| .. flat-table:: enum fe_status |
| :header-rows: 1 |
| :stub-columns: 0 |
| |
| |
| - .. row 1 |
| |
| - ID |
| |
| - Description |
| |
| - .. row 2 |
| |
| - .. _FE-HAS-SIGNAL: |
| |
| ``FE_HAS_SIGNAL`` |
| |
| - The frontend has found something above the noise level |
| |
| - .. row 3 |
| |
| - .. _FE-HAS-CARRIER: |
| |
| ``FE_HAS_CARRIER`` |
| |
| - The frontend has found a DVB signal |
| |
| - .. row 4 |
| |
| - .. _FE-HAS-VITERBI: |
| |
| ``FE_HAS_VITERBI`` |
| |
| - The frontend FEC inner coding (Viterbi, LDPC or other inner code) |
| is stable |
| |
| - .. row 5 |
| |
| - .. _FE-HAS-SYNC: |
| |
| ``FE_HAS_SYNC`` |
| |
| - Synchronization bytes was found |
| |
| - .. row 6 |
| |
| - .. _FE-HAS-LOCK: |
| |
| ``FE_HAS_LOCK`` |
| |
| - The DVB were locked and everything is working |
| |
| - .. row 7 |
| |
| - .. _FE-TIMEDOUT: |
| |
| ``FE_TIMEDOUT`` |
| |
| - no lock within the last about 2 seconds |
| |
| - .. row 8 |
| |
| - .. _FE-REINIT: |
| |
| ``FE_REINIT`` |
| |
| - The frontend was reinitialized, application is recommended to |
| reset DiSEqC, tone and parameters |
| |
| |
| Return Value |
| ============ |
| |
| On success 0 is returned, on error -1 and the ``errno`` variable is set |
| appropriately. The generic error codes are described at the |
| :ref:`Generic Error Codes <gen-errors>` chapter. |