| /* |
| * Synopsys DesignWare Multimedia Card Interface driver |
| * (Based on NXP driver for lpc 31xx) |
| * |
| * Copyright (C) 2009 NXP Semiconductors |
| * Copyright (C) 2009, 2010 Imagination Technologies Ltd. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation; either version 2 of the License, or |
| * (at your option) any later version. |
| */ |
| |
| #ifndef _DW_MMC_H_ |
| #define _DW_MMC_H_ |
| |
| #define DW_MMC_240A 0x240a |
| #define DW_MMC_280A 0x280a |
| |
| #define SDMMC_CTRL 0x000 |
| #define SDMMC_PWREN 0x004 |
| #define SDMMC_CLKDIV 0x008 |
| #define SDMMC_CLKSRC 0x00c |
| #define SDMMC_CLKENA 0x010 |
| #define SDMMC_TMOUT 0x014 |
| #define SDMMC_CTYPE 0x018 |
| #define SDMMC_BLKSIZ 0x01c |
| #define SDMMC_BYTCNT 0x020 |
| #define SDMMC_INTMASK 0x024 |
| #define SDMMC_CMDARG 0x028 |
| #define SDMMC_CMD 0x02c |
| #define SDMMC_RESP0 0x030 |
| #define SDMMC_RESP1 0x034 |
| #define SDMMC_RESP2 0x038 |
| #define SDMMC_RESP3 0x03c |
| #define SDMMC_MINTSTS 0x040 |
| #define SDMMC_RINTSTS 0x044 |
| #define SDMMC_STATUS 0x048 |
| #define SDMMC_FIFOTH 0x04c |
| #define SDMMC_CDETECT 0x050 |
| #define SDMMC_WRTPRT 0x054 |
| #define SDMMC_GPIO 0x058 |
| #define SDMMC_TCBCNT 0x05c |
| #define SDMMC_TBBCNT 0x060 |
| #define SDMMC_DEBNCE 0x064 |
| #define SDMMC_USRID 0x068 |
| #define SDMMC_VERID 0x06c |
| #define SDMMC_HCON 0x070 |
| #define SDMMC_UHS_REG 0x074 |
| #define SDMMC_RST_N 0x078 |
| #define SDMMC_BMOD 0x080 |
| #define SDMMC_PLDMND 0x084 |
| #define SDMMC_DBADDR 0x088 |
| #define SDMMC_IDSTS 0x08c |
| #define SDMMC_IDINTEN 0x090 |
| #define SDMMC_DSCADDR 0x094 |
| #define SDMMC_BUFADDR 0x098 |
| #define SDMMC_CDTHRCTL 0x100 |
| #define SDMMC_DATA(x) (x) |
| /* |
| * Registers to support idmac 64-bit address mode |
| */ |
| #define SDMMC_DBADDRL 0x088 |
| #define SDMMC_DBADDRU 0x08c |
| #define SDMMC_IDSTS64 0x090 |
| #define SDMMC_IDINTEN64 0x094 |
| #define SDMMC_DSCADDRL 0x098 |
| #define SDMMC_DSCADDRU 0x09c |
| #define SDMMC_BUFADDRL 0x0A0 |
| #define SDMMC_BUFADDRU 0x0A4 |
| |
| /* |
| * Data offset is difference according to Version |
| * Lower than 2.40a : data register offest is 0x100 |
| */ |
| #define DATA_OFFSET 0x100 |
| #define DATA_240A_OFFSET 0x200 |
| |
| /* shift bit field */ |
| #define _SBF(f, v) ((v) << (f)) |
| |
| /* Control register defines */ |
| #define SDMMC_CTRL_USE_IDMAC BIT(25) |
| #define SDMMC_CTRL_CEATA_INT_EN BIT(11) |
| #define SDMMC_CTRL_SEND_AS_CCSD BIT(10) |
| #define SDMMC_CTRL_SEND_CCSD BIT(9) |
| #define SDMMC_CTRL_ABRT_READ_DATA BIT(8) |
| #define SDMMC_CTRL_SEND_IRQ_RESP BIT(7) |
| #define SDMMC_CTRL_READ_WAIT BIT(6) |
| #define SDMMC_CTRL_DMA_ENABLE BIT(5) |
| #define SDMMC_CTRL_INT_ENABLE BIT(4) |
| #define SDMMC_CTRL_DMA_RESET BIT(2) |
| #define SDMMC_CTRL_FIFO_RESET BIT(1) |
| #define SDMMC_CTRL_RESET BIT(0) |
| /* Clock Enable register defines */ |
| #define SDMMC_CLKEN_LOW_PWR BIT(16) |
| #define SDMMC_CLKEN_ENABLE BIT(0) |
| /* time-out register defines */ |
| #define SDMMC_TMOUT_DATA(n) _SBF(8, (n)) |
| #define SDMMC_TMOUT_DATA_MSK 0xFFFFFF00 |
| #define SDMMC_TMOUT_RESP(n) ((n) & 0xFF) |
| #define SDMMC_TMOUT_RESP_MSK 0xFF |
| /* card-type register defines */ |
| #define SDMMC_CTYPE_8BIT BIT(16) |
| #define SDMMC_CTYPE_4BIT BIT(0) |
| #define SDMMC_CTYPE_1BIT 0 |
| /* Interrupt status & mask register defines */ |
| #define SDMMC_INT_SDIO(n) BIT(16 + (n)) |
| #define SDMMC_INT_EBE BIT(15) |
| #define SDMMC_INT_ACD BIT(14) |
| #define SDMMC_INT_SBE BIT(13) |
| #define SDMMC_INT_HLE BIT(12) |
| #define SDMMC_INT_FRUN BIT(11) |
| #define SDMMC_INT_HTO BIT(10) |
| #define SDMMC_INT_VOLT_SWITCH BIT(10) /* overloads bit 10! */ |
| #define SDMMC_INT_DRTO BIT(9) |
| #define SDMMC_INT_RTO BIT(8) |
| #define SDMMC_INT_DCRC BIT(7) |
| #define SDMMC_INT_RCRC BIT(6) |
| #define SDMMC_INT_RXDR BIT(5) |
| #define SDMMC_INT_TXDR BIT(4) |
| #define SDMMC_INT_DATA_OVER BIT(3) |
| #define SDMMC_INT_CMD_DONE BIT(2) |
| #define SDMMC_INT_RESP_ERR BIT(1) |
| #define SDMMC_INT_CD BIT(0) |
| #define SDMMC_INT_ERROR 0xbfc2 |
| /* Command register defines */ |
| #define SDMMC_CMD_START BIT(31) |
| #define SDMMC_CMD_USE_HOLD_REG BIT(29) |
| #define SDMMC_CMD_VOLT_SWITCH BIT(28) |
| #define SDMMC_CMD_CCS_EXP BIT(23) |
| #define SDMMC_CMD_CEATA_RD BIT(22) |
| #define SDMMC_CMD_UPD_CLK BIT(21) |
| #define SDMMC_CMD_INIT BIT(15) |
| #define SDMMC_CMD_STOP BIT(14) |
| #define SDMMC_CMD_PRV_DAT_WAIT BIT(13) |
| #define SDMMC_CMD_SEND_STOP BIT(12) |
| #define SDMMC_CMD_STRM_MODE BIT(11) |
| #define SDMMC_CMD_DAT_WR BIT(10) |
| #define SDMMC_CMD_DAT_EXP BIT(9) |
| #define SDMMC_CMD_RESP_CRC BIT(8) |
| #define SDMMC_CMD_RESP_LONG BIT(7) |
| #define SDMMC_CMD_RESP_EXP BIT(6) |
| #define SDMMC_CMD_INDX(n) ((n) & 0x1F) |
| /* Status register defines */ |
| #define SDMMC_GET_FCNT(x) (((x)>>17) & 0x1FFF) |
| #define SDMMC_STATUS_DMA_REQ BIT(31) |
| #define SDMMC_STATUS_BUSY BIT(9) |
| /* FIFOTH register defines */ |
| #define SDMMC_SET_FIFOTH(m, r, t) (((m) & 0x7) << 28 | \ |
| ((r) & 0xFFF) << 16 | \ |
| ((t) & 0xFFF)) |
| /* HCON register defines */ |
| #define DMA_INTERFACE_IDMA (0x0) |
| #define DMA_INTERFACE_DWDMA (0x1) |
| #define DMA_INTERFACE_GDMA (0x2) |
| #define DMA_INTERFACE_NODMA (0x3) |
| #define SDMMC_GET_TRANS_MODE(x) (((x)>>16) & 0x3) |
| #define SDMMC_GET_SLOT_NUM(x) ((((x)>>1) & 0x1F) + 1) |
| #define SDMMC_GET_HDATA_WIDTH(x) (((x)>>7) & 0x7) |
| #define SDMMC_GET_ADDR_CONFIG(x) (((x)>>27) & 0x1) |
| /* Internal DMAC interrupt defines */ |
| #define SDMMC_IDMAC_INT_AI BIT(9) |
| #define SDMMC_IDMAC_INT_NI BIT(8) |
| #define SDMMC_IDMAC_INT_CES BIT(5) |
| #define SDMMC_IDMAC_INT_DU BIT(4) |
| #define SDMMC_IDMAC_INT_FBE BIT(2) |
| #define SDMMC_IDMAC_INT_RI BIT(1) |
| #define SDMMC_IDMAC_INT_TI BIT(0) |
| /* Internal DMAC bus mode bits */ |
| #define SDMMC_IDMAC_ENABLE BIT(7) |
| #define SDMMC_IDMAC_FB BIT(1) |
| #define SDMMC_IDMAC_SWRESET BIT(0) |
| /* H/W reset */ |
| #define SDMMC_RST_HWACTIVE 0x1 |
| /* Version ID register define */ |
| #define SDMMC_GET_VERID(x) ((x) & 0xFFFF) |
| /* Card read threshold */ |
| #define SDMMC_SET_THLD(v, x) (((v) & 0xFFF) << 16 | (x)) |
| #define SDMMC_CARD_WR_THR_EN BIT(2) |
| #define SDMMC_CARD_RD_THR_EN BIT(0) |
| /* UHS-1 register defines */ |
| #define SDMMC_UHS_18V BIT(0) |
| /* All ctrl reset bits */ |
| #define SDMMC_CTRL_ALL_RESET_FLAGS \ |
| (SDMMC_CTRL_RESET | SDMMC_CTRL_FIFO_RESET | SDMMC_CTRL_DMA_RESET) |
| |
| /* FIFO register access macros. These should not change the data endian-ness |
| * as they are written to memory to be dealt with by the upper layers */ |
| #define mci_fifo_readw(__reg) __raw_readw(__reg) |
| #define mci_fifo_readl(__reg) __raw_readl(__reg) |
| #define mci_fifo_readq(__reg) __raw_readq(__reg) |
| |
| #define mci_fifo_writew(__value, __reg) __raw_writew(__reg, __value) |
| #define mci_fifo_writel(__value, __reg) __raw_writel(__reg, __value) |
| #define mci_fifo_writeq(__value, __reg) __raw_writeq(__reg, __value) |
| |
| /* Register access macros */ |
| #define mci_readl(dev, reg) \ |
| readl_relaxed((dev)->regs + SDMMC_##reg) |
| #define mci_writel(dev, reg, value) \ |
| writel_relaxed((value), (dev)->regs + SDMMC_##reg) |
| |
| /* 16-bit FIFO access macros */ |
| #define mci_readw(dev, reg) \ |
| readw_relaxed((dev)->regs + SDMMC_##reg) |
| #define mci_writew(dev, reg, value) \ |
| writew_relaxed((value), (dev)->regs + SDMMC_##reg) |
| |
| /* 64-bit FIFO access macros */ |
| #ifdef readq |
| #define mci_readq(dev, reg) \ |
| readq_relaxed((dev)->regs + SDMMC_##reg) |
| #define mci_writeq(dev, reg, value) \ |
| writeq_relaxed((value), (dev)->regs + SDMMC_##reg) |
| #else |
| /* |
| * Dummy readq implementation for architectures that don't define it. |
| * |
| * We would assume that none of these architectures would configure |
| * the IP block with a 64bit FIFO width, so this code will never be |
| * executed on those machines. Defining these macros here keeps the |
| * rest of the code free from ifdefs. |
| */ |
| #define mci_readq(dev, reg) \ |
| (*(volatile u64 __force *)((dev)->regs + SDMMC_##reg)) |
| #define mci_writeq(dev, reg, value) \ |
| (*(volatile u64 __force *)((dev)->regs + SDMMC_##reg) = (value)) |
| |
| #define __raw_writeq(__value, __reg) \ |
| (*(volatile u64 __force *)(__reg) = (__value)) |
| #define __raw_readq(__reg) (*(volatile u64 __force *)(__reg)) |
| #endif |
| |
| extern int dw_mci_probe(struct dw_mci *host); |
| extern void dw_mci_remove(struct dw_mci *host); |
| #ifdef CONFIG_PM |
| extern int dw_mci_runtime_suspend(struct device *device); |
| extern int dw_mci_runtime_resume(struct device *device); |
| #endif |
| |
| /** |
| * struct dw_mci_slot - MMC slot state |
| * @mmc: The mmc_host representing this slot. |
| * @host: The MMC controller this slot is using. |
| * @ctype: Card type for this slot. |
| * @mrq: mmc_request currently being processed or waiting to be |
| * processed, or NULL when the slot is idle. |
| * @queue_node: List node for placing this node in the @queue list of |
| * &struct dw_mci. |
| * @clock: Clock rate configured by set_ios(). Protected by host->lock. |
| * @__clk_old: The last clock value that was requested from core. |
| * Keeping track of this helps us to avoid spamming the console. |
| * @flags: Random state bits associated with the slot. |
| * @id: Number of this slot. |
| * @sdio_id: Number of this slot in the SDIO interrupt registers. |
| */ |
| struct dw_mci_slot { |
| struct mmc_host *mmc; |
| struct dw_mci *host; |
| |
| u32 ctype; |
| |
| struct mmc_request *mrq; |
| struct list_head queue_node; |
| |
| unsigned int clock; |
| unsigned int __clk_old; |
| |
| unsigned long flags; |
| #define DW_MMC_CARD_PRESENT 0 |
| #define DW_MMC_CARD_NEED_INIT 1 |
| #define DW_MMC_CARD_NO_LOW_PWR 2 |
| #define DW_MMC_CARD_NO_USE_HOLD 3 |
| #define DW_MMC_CARD_NEEDS_POLL 4 |
| int id; |
| int sdio_id; |
| }; |
| |
| /** |
| * dw_mci driver data - dw-mshc implementation specific driver data. |
| * @caps: mmc subsystem specified capabilities of the controller(s). |
| * @init: early implementation specific initialization. |
| * @set_ios: handle bus specific extensions. |
| * @parse_dt: parse implementation specific device tree properties. |
| * @execute_tuning: implementation specific tuning procedure. |
| * |
| * Provide controller implementation specific extensions. The usage of this |
| * data structure is fully optional and usage of each member in this structure |
| * is optional as well. |
| */ |
| struct dw_mci_drv_data { |
| unsigned long *caps; |
| int (*init)(struct dw_mci *host); |
| void (*set_ios)(struct dw_mci *host, struct mmc_ios *ios); |
| int (*parse_dt)(struct dw_mci *host); |
| int (*execute_tuning)(struct dw_mci_slot *slot, u32 opcode); |
| int (*prepare_hs400_tuning)(struct dw_mci *host, |
| struct mmc_ios *ios); |
| int (*switch_voltage)(struct mmc_host *mmc, |
| struct mmc_ios *ios); |
| }; |
| #endif /* _DW_MMC_H_ */ |