| /* |
| * Copyright (c) 2005-2011 Atheros Communications Inc. |
| * Copyright (c) 2011-2013 Qualcomm Atheros, Inc. |
| * |
| * Permission to use, copy, modify, and/or distribute this software for any |
| * purpose with or without fee is hereby granted, provided that the above |
| * copyright notice and this permission notice appear in all copies. |
| * |
| * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES |
| * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF |
| * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR |
| * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES |
| * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN |
| * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF |
| * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. |
| */ |
| |
| #ifndef __TARGADDRS_H__ |
| #define __TARGADDRS_H__ |
| |
| #include "hw.h" |
| |
| /* |
| * xxx_HOST_INTEREST_ADDRESS is the address in Target RAM of the |
| * host_interest structure. It must match the address of the _host_interest |
| * symbol (see linker script). |
| * |
| * Host Interest is shared between Host and Target in order to coordinate |
| * between the two, and is intended to remain constant (with additions only |
| * at the end) across software releases. |
| * |
| * All addresses are available here so that it's possible to |
| * write a single binary that works with all Target Types. |
| * May be used in assembler code as well as C. |
| */ |
| #define QCA988X_HOST_INTEREST_ADDRESS 0x00400800 |
| #define HOST_INTEREST_MAX_SIZE 0x200 |
| |
| /* |
| * These are items that the Host may need to access via BMI or via the |
| * Diagnostic Window. The position of items in this structure must remain |
| * constant across firmware revisions! Types for each item must be fixed |
| * size across target and host platforms. More items may be added at the end. |
| */ |
| struct host_interest { |
| /* |
| * Pointer to application-defined area, if any. |
| * Set by Target application during startup. |
| */ |
| u32 hi_app_host_interest; /* 0x00 */ |
| |
| /* Pointer to register dump area, valid after Target crash. */ |
| u32 hi_failure_state; /* 0x04 */ |
| |
| /* Pointer to debug logging header */ |
| u32 hi_dbglog_hdr; /* 0x08 */ |
| |
| u32 hi_unused0c; /* 0x0c */ |
| |
| /* |
| * General-purpose flag bits, similar to SOC_OPTION_* flags. |
| * Can be used by application rather than by OS. |
| */ |
| u32 hi_option_flag; /* 0x10 */ |
| |
| /* |
| * Boolean that determines whether or not to |
| * display messages on the serial port. |
| */ |
| u32 hi_serial_enable; /* 0x14 */ |
| |
| /* Start address of DataSet index, if any */ |
| u32 hi_dset_list_head; /* 0x18 */ |
| |
| /* Override Target application start address */ |
| u32 hi_app_start; /* 0x1c */ |
| |
| /* Clock and voltage tuning */ |
| u32 hi_skip_clock_init; /* 0x20 */ |
| u32 hi_core_clock_setting; /* 0x24 */ |
| u32 hi_cpu_clock_setting; /* 0x28 */ |
| u32 hi_system_sleep_setting; /* 0x2c */ |
| u32 hi_xtal_control_setting; /* 0x30 */ |
| u32 hi_pll_ctrl_setting_24ghz; /* 0x34 */ |
| u32 hi_pll_ctrl_setting_5ghz; /* 0x38 */ |
| u32 hi_ref_voltage_trim_setting; /* 0x3c */ |
| u32 hi_clock_info; /* 0x40 */ |
| |
| /* Host uses BE CPU or not */ |
| u32 hi_be; /* 0x44 */ |
| |
| u32 hi_stack; /* normal stack */ /* 0x48 */ |
| u32 hi_err_stack; /* error stack */ /* 0x4c */ |
| u32 hi_desired_cpu_speed_hz; /* 0x50 */ |
| |
| /* Pointer to Board Data */ |
| u32 hi_board_data; /* 0x54 */ |
| |
| /* |
| * Indication of Board Data state: |
| * 0: board data is not yet initialized. |
| * 1: board data is initialized; unknown size |
| * >1: number of bytes of initialized board data |
| */ |
| u32 hi_board_data_initialized; /* 0x58 */ |
| |
| u32 hi_dset_ram_index_table; /* 0x5c */ |
| |
| u32 hi_desired_baud_rate; /* 0x60 */ |
| u32 hi_dbglog_config; /* 0x64 */ |
| u32 hi_end_ram_reserve_sz; /* 0x68 */ |
| u32 hi_mbox_io_block_sz; /* 0x6c */ |
| |
| u32 hi_num_bpatch_streams; /* 0x70 -- unused */ |
| u32 hi_mbox_isr_yield_limit; /* 0x74 */ |
| |
| u32 hi_refclk_hz; /* 0x78 */ |
| u32 hi_ext_clk_detected; /* 0x7c */ |
| u32 hi_dbg_uart_txpin; /* 0x80 */ |
| u32 hi_dbg_uart_rxpin; /* 0x84 */ |
| u32 hi_hci_uart_baud; /* 0x88 */ |
| u32 hi_hci_uart_pin_assignments; /* 0x8C */ |
| |
| u32 hi_hci_uart_baud_scale_val; /* 0x90 */ |
| u32 hi_hci_uart_baud_step_val; /* 0x94 */ |
| |
| u32 hi_allocram_start; /* 0x98 */ |
| u32 hi_allocram_sz; /* 0x9c */ |
| u32 hi_hci_bridge_flags; /* 0xa0 */ |
| u32 hi_hci_uart_support_pins; /* 0xa4 */ |
| |
| u32 hi_hci_uart_pwr_mgmt_params; /* 0xa8 */ |
| |
| /* |
| * 0xa8 - [1]: 0 = UART FC active low, 1 = UART FC active high |
| * [31:16]: wakeup timeout in ms |
| */ |
| /* Pointer to extended board Data */ |
| u32 hi_board_ext_data; /* 0xac */ |
| u32 hi_board_ext_data_config; /* 0xb0 */ |
| /* |
| * Bit [0] : valid |
| * Bit[31:16: size |
| */ |
| /* |
| * hi_reset_flag is used to do some stuff when target reset. |
| * such as restore app_start after warm reset or |
| * preserve host Interest area, or preserve ROM data, literals etc. |
| */ |
| u32 hi_reset_flag; /* 0xb4 */ |
| /* indicate hi_reset_flag is valid */ |
| u32 hi_reset_flag_valid; /* 0xb8 */ |
| u32 hi_hci_uart_pwr_mgmt_params_ext; /* 0xbc */ |
| /* 0xbc - [31:0]: idle timeout in ms */ |
| /* ACS flags */ |
| u32 hi_acs_flags; /* 0xc0 */ |
| u32 hi_console_flags; /* 0xc4 */ |
| u32 hi_nvram_state; /* 0xc8 */ |
| u32 hi_option_flag2; /* 0xcc */ |
| |
| /* If non-zero, override values sent to Host in WMI_READY event. */ |
| u32 hi_sw_version_override; /* 0xd0 */ |
| u32 hi_abi_version_override; /* 0xd4 */ |
| |
| /* |
| * Percentage of high priority RX traffic to total expected RX traffic |
| * applicable only to ar6004 |
| */ |
| u32 hi_hp_rx_traffic_ratio; /* 0xd8 */ |
| |
| /* test applications flags */ |
| u32 hi_test_apps_related; /* 0xdc */ |
| /* location of test script */ |
| u32 hi_ota_testscript; /* 0xe0 */ |
| /* location of CAL data */ |
| u32 hi_cal_data; /* 0xe4 */ |
| |
| /* Number of packet log buffers */ |
| u32 hi_pktlog_num_buffers; /* 0xe8 */ |
| |
| /* wow extension configuration */ |
| u32 hi_wow_ext_config; /* 0xec */ |
| u32 hi_pwr_save_flags; /* 0xf0 */ |
| |
| /* Spatial Multiplexing Power Save (SMPS) options */ |
| u32 hi_smps_options; /* 0xf4 */ |
| |
| /* Interconnect-specific state */ |
| u32 hi_interconnect_state; /* 0xf8 */ |
| |
| /* Coex configuration flags */ |
| u32 hi_coex_config; /* 0xfc */ |
| |
| /* Early allocation support */ |
| u32 hi_early_alloc; /* 0x100 */ |
| /* FW swap field */ |
| /* |
| * Bits of this 32bit word will be used to pass specific swap |
| * instruction to FW |
| */ |
| /* |
| * Bit 0 -- AP Nart descriptor no swap. When this bit is set |
| * FW will not swap TX descriptor. Meaning packets are formed |
| * on the target processor. |
| */ |
| /* Bit 1 - unused */ |
| u32 hi_fw_swap; /* 0x104 */ |
| } __packed; |
| |
| #define HI_ITEM(item) offsetof(struct host_interest, item) |
| |
| /* Bits defined in hi_option_flag */ |
| |
| /* Enable timer workaround */ |
| #define HI_OPTION_TIMER_WAR 0x01 |
| /* Limit BMI command credits */ |
| #define HI_OPTION_BMI_CRED_LIMIT 0x02 |
| /* Relay Dot11 hdr to/from host */ |
| #define HI_OPTION_RELAY_DOT11_HDR 0x04 |
| /* MAC addr method 0-locally administred 1-globally unique addrs */ |
| #define HI_OPTION_MAC_ADDR_METHOD 0x08 |
| /* Firmware Bridging */ |
| #define HI_OPTION_FW_BRIDGE 0x10 |
| /* Enable CPU profiling */ |
| #define HI_OPTION_ENABLE_PROFILE 0x20 |
| /* Disable debug logging */ |
| #define HI_OPTION_DISABLE_DBGLOG 0x40 |
| /* Skip Era Tracking */ |
| #define HI_OPTION_SKIP_ERA_TRACKING 0x80 |
| /* Disable PAPRD (debug) */ |
| #define HI_OPTION_PAPRD_DISABLE 0x100 |
| #define HI_OPTION_NUM_DEV_LSB 0x200 |
| #define HI_OPTION_NUM_DEV_MSB 0x800 |
| #define HI_OPTION_DEV_MODE_LSB 0x1000 |
| #define HI_OPTION_DEV_MODE_MSB 0x8000000 |
| /* Disable LowFreq Timer Stabilization */ |
| #define HI_OPTION_NO_LFT_STBL 0x10000000 |
| /* Skip regulatory scan */ |
| #define HI_OPTION_SKIP_REG_SCAN 0x20000000 |
| /* |
| * Do regulatory scan during init before |
| * sending WMI ready event to host |
| */ |
| #define HI_OPTION_INIT_REG_SCAN 0x40000000 |
| |
| /* REV6: Do not adjust memory map */ |
| #define HI_OPTION_SKIP_MEMMAP 0x80000000 |
| |
| #define HI_OPTION_MAC_ADDR_METHOD_SHIFT 3 |
| |
| /* 2 bits of hi_option_flag are used to represent 3 modes */ |
| #define HI_OPTION_FW_MODE_IBSS 0x0 /* IBSS Mode */ |
| #define HI_OPTION_FW_MODE_BSS_STA 0x1 /* STA Mode */ |
| #define HI_OPTION_FW_MODE_AP 0x2 /* AP Mode */ |
| #define HI_OPTION_FW_MODE_BT30AMP 0x3 /* BT30 AMP Mode */ |
| |
| /* 2 bits of hi_option flag are usedto represent 4 submodes */ |
| #define HI_OPTION_FW_SUBMODE_NONE 0x0 /* Normal mode */ |
| #define HI_OPTION_FW_SUBMODE_P2PDEV 0x1 /* p2p device mode */ |
| #define HI_OPTION_FW_SUBMODE_P2PCLIENT 0x2 /* p2p client mode */ |
| #define HI_OPTION_FW_SUBMODE_P2PGO 0x3 /* p2p go mode */ |
| |
| /* Num dev Mask */ |
| #define HI_OPTION_NUM_DEV_MASK 0x7 |
| #define HI_OPTION_NUM_DEV_SHIFT 0x9 |
| |
| /* firmware bridging */ |
| #define HI_OPTION_FW_BRIDGE_SHIFT 0x04 |
| |
| /* |
| Fw Mode/SubMode Mask |
| |-----------------------------------------------------------------------------| |
| | SUB | SUB | SUB | SUB | | | | | |
| |MODE[3] | MODE[2] | MODE[1] | MODE[0] | MODE[3] | MODE[2] | MODE[1] | MODE[0]| |
| | (2) | (2) | (2) | (2) | (2) | (2) | (2) | (2) | |
| |-----------------------------------------------------------------------------| |
| */ |
| #define HI_OPTION_FW_MODE_BITS 0x2 |
| #define HI_OPTION_FW_MODE_MASK 0x3 |
| #define HI_OPTION_FW_MODE_SHIFT 0xC |
| #define HI_OPTION_ALL_FW_MODE_MASK 0xFF |
| |
| #define HI_OPTION_FW_SUBMODE_BITS 0x2 |
| #define HI_OPTION_FW_SUBMODE_MASK 0x3 |
| #define HI_OPTION_FW_SUBMODE_SHIFT 0x14 |
| #define HI_OPTION_ALL_FW_SUBMODE_MASK 0xFF00 |
| #define HI_OPTION_ALL_FW_SUBMODE_SHIFT 0x8 |
| |
| /* hi_option_flag2 options */ |
| #define HI_OPTION_OFFLOAD_AMSDU 0x01 |
| #define HI_OPTION_DFS_SUPPORT 0x02 /* Enable DFS support */ |
| #define HI_OPTION_ENABLE_RFKILL 0x04 /* RFKill Enable Feature*/ |
| #define HI_OPTION_RADIO_RETENTION_DISABLE 0x08 /* Disable radio retention */ |
| #define HI_OPTION_EARLY_CFG_DONE 0x10 /* Early configuration is complete */ |
| |
| #define HI_OPTION_RF_KILL_SHIFT 0x2 |
| #define HI_OPTION_RF_KILL_MASK 0x1 |
| |
| /* hi_reset_flag */ |
| /* preserve App Start address */ |
| #define HI_RESET_FLAG_PRESERVE_APP_START 0x01 |
| /* preserve host interest */ |
| #define HI_RESET_FLAG_PRESERVE_HOST_INTEREST 0x02 |
| /* preserve ROM data */ |
| #define HI_RESET_FLAG_PRESERVE_ROMDATA 0x04 |
| #define HI_RESET_FLAG_PRESERVE_NVRAM_STATE 0x08 |
| #define HI_RESET_FLAG_PRESERVE_BOOT_INFO 0x10 |
| #define HI_RESET_FLAG_WARM_RESET 0x20 |
| |
| /* define hi_fw_swap bits */ |
| #define HI_DESC_IN_FW_BIT 0x01 |
| |
| /* indicate the reset flag is valid */ |
| #define HI_RESET_FLAG_IS_VALID 0x12345678 |
| |
| /* ACS is enabled */ |
| #define HI_ACS_FLAGS_ENABLED (1 << 0) |
| /* Use physical WWAN device */ |
| #define HI_ACS_FLAGS_USE_WWAN (1 << 1) |
| /* Use test VAP */ |
| #define HI_ACS_FLAGS_TEST_VAP (1 << 2) |
| |
| /* |
| * CONSOLE FLAGS |
| * |
| * Bit Range Meaning |
| * --------- -------------------------------- |
| * 2..0 UART ID (0 = Default) |
| * 3 Baud Select (0 = 9600, 1 = 115200) |
| * 30..4 Reserved |
| * 31 Enable Console |
| * |
| */ |
| |
| #define HI_CONSOLE_FLAGS_ENABLE (1 << 31) |
| #define HI_CONSOLE_FLAGS_UART_MASK (0x7) |
| #define HI_CONSOLE_FLAGS_UART_SHIFT 0 |
| #define HI_CONSOLE_FLAGS_BAUD_SELECT (1 << 3) |
| |
| /* SM power save options */ |
| #define HI_SMPS_ALLOW_MASK (0x00000001) |
| #define HI_SMPS_MODE_MASK (0x00000002) |
| #define HI_SMPS_MODE_STATIC (0x00000000) |
| #define HI_SMPS_MODE_DYNAMIC (0x00000002) |
| #define HI_SMPS_DISABLE_AUTO_MODE (0x00000004) |
| #define HI_SMPS_DATA_THRESH_MASK (0x000007f8) |
| #define HI_SMPS_DATA_THRESH_SHIFT (3) |
| #define HI_SMPS_RSSI_THRESH_MASK (0x0007f800) |
| #define HI_SMPS_RSSI_THRESH_SHIFT (11) |
| #define HI_SMPS_LOWPWR_CM_MASK (0x00380000) |
| #define HI_SMPS_LOWPWR_CM_SHIFT (15) |
| #define HI_SMPS_HIPWR_CM_MASK (0x03c00000) |
| #define HI_SMPS_HIPWR_CM_SHIFT (19) |
| |
| /* |
| * WOW Extension configuration |
| * |
| * Bit Range Meaning |
| * --------- -------------------------------- |
| * 8..0 Size of each WOW pattern (max 511) |
| * 15..9 Number of patterns per list (max 127) |
| * 17..16 Number of lists (max 4) |
| * 30..18 Reserved |
| * 31 Enabled |
| * |
| * set values (except enable) to zeros for default settings |
| */ |
| |
| #define HI_WOW_EXT_ENABLED_MASK (1 << 31) |
| #define HI_WOW_EXT_NUM_LIST_SHIFT 16 |
| #define HI_WOW_EXT_NUM_LIST_MASK (0x3 << HI_WOW_EXT_NUM_LIST_SHIFT) |
| #define HI_WOW_EXT_NUM_PATTERNS_SHIFT 9 |
| #define HI_WOW_EXT_NUM_PATTERNS_MASK (0x7F << HI_WOW_EXT_NUM_PATTERNS_SHIFT) |
| #define HI_WOW_EXT_PATTERN_SIZE_SHIFT 0 |
| #define HI_WOW_EXT_PATTERN_SIZE_MASK (0x1FF << HI_WOW_EXT_PATTERN_SIZE_SHIFT) |
| |
| #define HI_WOW_EXT_MAKE_CONFIG(num_lists, count, size) \ |
| ((((num_lists) << HI_WOW_EXT_NUM_LIST_SHIFT) & \ |
| HI_WOW_EXT_NUM_LIST_MASK) | \ |
| (((count) << HI_WOW_EXT_NUM_PATTERNS_SHIFT) & \ |
| HI_WOW_EXT_NUM_PATTERNS_MASK) | \ |
| (((size) << HI_WOW_EXT_PATTERN_SIZE_SHIFT) & \ |
| HI_WOW_EXT_PATTERN_SIZE_MASK)) |
| |
| #define HI_WOW_EXT_GET_NUM_LISTS(config) \ |
| (((config) & HI_WOW_EXT_NUM_LIST_MASK) >> HI_WOW_EXT_NUM_LIST_SHIFT) |
| #define HI_WOW_EXT_GET_NUM_PATTERNS(config) \ |
| (((config) & HI_WOW_EXT_NUM_PATTERNS_MASK) >> \ |
| HI_WOW_EXT_NUM_PATTERNS_SHIFT) |
| #define HI_WOW_EXT_GET_PATTERN_SIZE(config) \ |
| (((config) & HI_WOW_EXT_PATTERN_SIZE_MASK) >> \ |
| HI_WOW_EXT_PATTERN_SIZE_SHIFT) |
| |
| /* |
| * Early allocation configuration |
| * Support RAM bank configuration before BMI done and this eases the memory |
| * allocation at very early stage |
| * Bit Range Meaning |
| * --------- ---------------------------------- |
| * [0:3] number of bank assigned to be IRAM |
| * [4:15] reserved |
| * [16:31] magic number |
| * |
| * Note: |
| * 1. target firmware would check magic number and if it's a match, firmware |
| * would consider the bits[0:15] are valid and base on that to calculate |
| * the end of DRAM. Early allocation would be located at that area and |
| * may be reclaimed when necesary |
| * 2. if no magic number is found, early allocation would happen at "_end" |
| * symbol of ROM which is located before the app-data and might NOT be |
| * re-claimable. If this is adopted, link script should keep this in |
| * mind to avoid data corruption. |
| */ |
| #define HI_EARLY_ALLOC_MAGIC 0x6d8a |
| #define HI_EARLY_ALLOC_MAGIC_MASK 0xffff0000 |
| #define HI_EARLY_ALLOC_MAGIC_SHIFT 16 |
| #define HI_EARLY_ALLOC_IRAM_BANKS_MASK 0x0000000f |
| #define HI_EARLY_ALLOC_IRAM_BANKS_SHIFT 0 |
| |
| #define HI_EARLY_ALLOC_VALID() \ |
| ((((HOST_INTEREST->hi_early_alloc) & HI_EARLY_ALLOC_MAGIC_MASK) >> \ |
| HI_EARLY_ALLOC_MAGIC_SHIFT) == (HI_EARLY_ALLOC_MAGIC)) |
| #define HI_EARLY_ALLOC_GET_IRAM_BANKS() \ |
| (((HOST_INTEREST->hi_early_alloc) & HI_EARLY_ALLOC_IRAM_BANKS_MASK) \ |
| >> HI_EARLY_ALLOC_IRAM_BANKS_SHIFT) |
| |
| /*power save flag bit definitions*/ |
| #define HI_PWR_SAVE_LPL_ENABLED 0x1 |
| /*b1-b3 reserved*/ |
| /*b4-b5 : dev0 LPL type : 0 - none |
| 1- Reduce Pwr Search |
| 2- Reduce Pwr Listen*/ |
| /*b6-b7 : dev1 LPL type and so on for Max 8 devices*/ |
| #define HI_PWR_SAVE_LPL_DEV0_LSB 4 |
| #define HI_PWR_SAVE_LPL_DEV_MASK 0x3 |
| /*power save related utility macros*/ |
| #define HI_LPL_ENABLED() \ |
| ((HOST_INTEREST->hi_pwr_save_flags & HI_PWR_SAVE_LPL_ENABLED)) |
| #define HI_DEV_LPL_TYPE_GET(_devix) \ |
| (HOST_INTEREST->hi_pwr_save_flags & ((HI_PWR_SAVE_LPL_DEV_MASK) << \ |
| (HI_PWR_SAVE_LPL_DEV0_LSB + (_devix) * 2))) |
| |
| #define HOST_INTEREST_SMPS_IS_ALLOWED() \ |
| ((HOST_INTEREST->hi_smps_options & HI_SMPS_ALLOW_MASK)) |
| |
| /* Reserve 1024 bytes for extended board data */ |
| #define QCA988X_BOARD_DATA_SZ 7168 |
| #define QCA988X_BOARD_EXT_DATA_SZ 0 |
| |
| #define QCA9887_BOARD_DATA_SZ 7168 |
| #define QCA9887_BOARD_EXT_DATA_SZ 0 |
| |
| #define QCA6174_BOARD_DATA_SZ 8192 |
| #define QCA6174_BOARD_EXT_DATA_SZ 0 |
| |
| #define QCA9377_BOARD_DATA_SZ QCA6174_BOARD_DATA_SZ |
| #define QCA9377_BOARD_EXT_DATA_SZ 0 |
| |
| #define QCA99X0_BOARD_DATA_SZ 12288 |
| #define QCA99X0_BOARD_EXT_DATA_SZ 0 |
| |
| #define QCA4019_BOARD_DATA_SZ 12064 |
| #define QCA4019_BOARD_EXT_DATA_SZ 0 |
| |
| #endif /* __TARGADDRS_H__ */ |