| /* |
| * Copyright (C) 2005-2006 Atmel Corporation |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 as |
| * published by the Free Software Foundation. |
| */ |
| #include <linux/clk.h> |
| #include <linux/init.h> |
| #include <linux/platform_device.h> |
| #include <linux/spi/spi.h> |
| |
| #include <asm/io.h> |
| |
| #include <asm/arch/at32ap7000.h> |
| #include <asm/arch/board.h> |
| #include <asm/arch/portmux.h> |
| #include <asm/arch/sm.h> |
| |
| #include "clock.h" |
| #include "pio.h" |
| #include "sm.h" |
| |
| #define PBMEM(base) \ |
| { \ |
| .start = base, \ |
| .end = base + 0x3ff, \ |
| .flags = IORESOURCE_MEM, \ |
| } |
| #define IRQ(num) \ |
| { \ |
| .start = num, \ |
| .end = num, \ |
| .flags = IORESOURCE_IRQ, \ |
| } |
| #define NAMED_IRQ(num, _name) \ |
| { \ |
| .start = num, \ |
| .end = num, \ |
| .name = _name, \ |
| .flags = IORESOURCE_IRQ, \ |
| } |
| |
| #define DEFINE_DEV(_name, _id) \ |
| static struct platform_device _name##_id##_device = { \ |
| .name = #_name, \ |
| .id = _id, \ |
| .resource = _name##_id##_resource, \ |
| .num_resources = ARRAY_SIZE(_name##_id##_resource), \ |
| } |
| #define DEFINE_DEV_DATA(_name, _id) \ |
| static struct platform_device _name##_id##_device = { \ |
| .name = #_name, \ |
| .id = _id, \ |
| .dev = { \ |
| .platform_data = &_name##_id##_data, \ |
| }, \ |
| .resource = _name##_id##_resource, \ |
| .num_resources = ARRAY_SIZE(_name##_id##_resource), \ |
| } |
| |
| #define select_peripheral(pin, periph, flags) \ |
| at32_select_periph(GPIO_PIN_##pin, GPIO_##periph, flags) |
| |
| #define DEV_CLK(_name, devname, bus, _index) \ |
| static struct clk devname##_##_name = { \ |
| .name = #_name, \ |
| .dev = &devname##_device.dev, \ |
| .parent = &bus##_clk, \ |
| .mode = bus##_clk_mode, \ |
| .get_rate = bus##_clk_get_rate, \ |
| .index = _index, \ |
| } |
| |
| unsigned long at32ap7000_osc_rates[3] = { |
| [0] = 32768, |
| /* FIXME: these are ATSTK1002-specific */ |
| [1] = 20000000, |
| [2] = 12000000, |
| }; |
| |
| static unsigned long osc_get_rate(struct clk *clk) |
| { |
| return at32ap7000_osc_rates[clk->index]; |
| } |
| |
| static unsigned long pll_get_rate(struct clk *clk, unsigned long control) |
| { |
| unsigned long div, mul, rate; |
| |
| if (!(control & SM_BIT(PLLEN))) |
| return 0; |
| |
| div = SM_BFEXT(PLLDIV, control) + 1; |
| mul = SM_BFEXT(PLLMUL, control) + 1; |
| |
| rate = clk->parent->get_rate(clk->parent); |
| rate = (rate + div / 2) / div; |
| rate *= mul; |
| |
| return rate; |
| } |
| |
| static unsigned long pll0_get_rate(struct clk *clk) |
| { |
| u32 control; |
| |
| control = sm_readl(&system_manager, PM_PLL0); |
| |
| return pll_get_rate(clk, control); |
| } |
| |
| static unsigned long pll1_get_rate(struct clk *clk) |
| { |
| u32 control; |
| |
| control = sm_readl(&system_manager, PM_PLL1); |
| |
| return pll_get_rate(clk, control); |
| } |
| |
| /* |
| * The AT32AP7000 has five primary clock sources: One 32kHz |
| * oscillator, two crystal oscillators and two PLLs. |
| */ |
| static struct clk osc32k = { |
| .name = "osc32k", |
| .get_rate = osc_get_rate, |
| .users = 1, |
| .index = 0, |
| }; |
| static struct clk osc0 = { |
| .name = "osc0", |
| .get_rate = osc_get_rate, |
| .users = 1, |
| .index = 1, |
| }; |
| static struct clk osc1 = { |
| .name = "osc1", |
| .get_rate = osc_get_rate, |
| .index = 2, |
| }; |
| static struct clk pll0 = { |
| .name = "pll0", |
| .get_rate = pll0_get_rate, |
| .parent = &osc0, |
| }; |
| static struct clk pll1 = { |
| .name = "pll1", |
| .get_rate = pll1_get_rate, |
| .parent = &osc0, |
| }; |
| |
| /* |
| * The main clock can be either osc0 or pll0. The boot loader may |
| * have chosen one for us, so we don't really know which one until we |
| * have a look at the SM. |
| */ |
| static struct clk *main_clock; |
| |
| /* |
| * Synchronous clocks are generated from the main clock. The clocks |
| * must satisfy the constraint |
| * fCPU >= fHSB >= fPB |
| * i.e. each clock must not be faster than its parent. |
| */ |
| static unsigned long bus_clk_get_rate(struct clk *clk, unsigned int shift) |
| { |
| return main_clock->get_rate(main_clock) >> shift; |
| }; |
| |
| static void cpu_clk_mode(struct clk *clk, int enabled) |
| { |
| struct at32_sm *sm = &system_manager; |
| unsigned long flags; |
| u32 mask; |
| |
| spin_lock_irqsave(&sm->lock, flags); |
| mask = sm_readl(sm, PM_CPU_MASK); |
| if (enabled) |
| mask |= 1 << clk->index; |
| else |
| mask &= ~(1 << clk->index); |
| sm_writel(sm, PM_CPU_MASK, mask); |
| spin_unlock_irqrestore(&sm->lock, flags); |
| } |
| |
| static unsigned long cpu_clk_get_rate(struct clk *clk) |
| { |
| unsigned long cksel, shift = 0; |
| |
| cksel = sm_readl(&system_manager, PM_CKSEL); |
| if (cksel & SM_BIT(CPUDIV)) |
| shift = SM_BFEXT(CPUSEL, cksel) + 1; |
| |
| return bus_clk_get_rate(clk, shift); |
| } |
| |
| static void hsb_clk_mode(struct clk *clk, int enabled) |
| { |
| struct at32_sm *sm = &system_manager; |
| unsigned long flags; |
| u32 mask; |
| |
| spin_lock_irqsave(&sm->lock, flags); |
| mask = sm_readl(sm, PM_HSB_MASK); |
| if (enabled) |
| mask |= 1 << clk->index; |
| else |
| mask &= ~(1 << clk->index); |
| sm_writel(sm, PM_HSB_MASK, mask); |
| spin_unlock_irqrestore(&sm->lock, flags); |
| } |
| |
| static unsigned long hsb_clk_get_rate(struct clk *clk) |
| { |
| unsigned long cksel, shift = 0; |
| |
| cksel = sm_readl(&system_manager, PM_CKSEL); |
| if (cksel & SM_BIT(HSBDIV)) |
| shift = SM_BFEXT(HSBSEL, cksel) + 1; |
| |
| return bus_clk_get_rate(clk, shift); |
| } |
| |
| static void pba_clk_mode(struct clk *clk, int enabled) |
| { |
| struct at32_sm *sm = &system_manager; |
| unsigned long flags; |
| u32 mask; |
| |
| spin_lock_irqsave(&sm->lock, flags); |
| mask = sm_readl(sm, PM_PBA_MASK); |
| if (enabled) |
| mask |= 1 << clk->index; |
| else |
| mask &= ~(1 << clk->index); |
| sm_writel(sm, PM_PBA_MASK, mask); |
| spin_unlock_irqrestore(&sm->lock, flags); |
| } |
| |
| static unsigned long pba_clk_get_rate(struct clk *clk) |
| { |
| unsigned long cksel, shift = 0; |
| |
| cksel = sm_readl(&system_manager, PM_CKSEL); |
| if (cksel & SM_BIT(PBADIV)) |
| shift = SM_BFEXT(PBASEL, cksel) + 1; |
| |
| return bus_clk_get_rate(clk, shift); |
| } |
| |
| static void pbb_clk_mode(struct clk *clk, int enabled) |
| { |
| struct at32_sm *sm = &system_manager; |
| unsigned long flags; |
| u32 mask; |
| |
| spin_lock_irqsave(&sm->lock, flags); |
| mask = sm_readl(sm, PM_PBB_MASK); |
| if (enabled) |
| mask |= 1 << clk->index; |
| else |
| mask &= ~(1 << clk->index); |
| sm_writel(sm, PM_PBB_MASK, mask); |
| spin_unlock_irqrestore(&sm->lock, flags); |
| } |
| |
| static unsigned long pbb_clk_get_rate(struct clk *clk) |
| { |
| unsigned long cksel, shift = 0; |
| |
| cksel = sm_readl(&system_manager, PM_CKSEL); |
| if (cksel & SM_BIT(PBBDIV)) |
| shift = SM_BFEXT(PBBSEL, cksel) + 1; |
| |
| return bus_clk_get_rate(clk, shift); |
| } |
| |
| static struct clk cpu_clk = { |
| .name = "cpu", |
| .get_rate = cpu_clk_get_rate, |
| .users = 1, |
| }; |
| static struct clk hsb_clk = { |
| .name = "hsb", |
| .parent = &cpu_clk, |
| .get_rate = hsb_clk_get_rate, |
| }; |
| static struct clk pba_clk = { |
| .name = "pba", |
| .parent = &hsb_clk, |
| .mode = hsb_clk_mode, |
| .get_rate = pba_clk_get_rate, |
| .index = 1, |
| }; |
| static struct clk pbb_clk = { |
| .name = "pbb", |
| .parent = &hsb_clk, |
| .mode = hsb_clk_mode, |
| .get_rate = pbb_clk_get_rate, |
| .users = 1, |
| .index = 2, |
| }; |
| |
| /* -------------------------------------------------------------------- |
| * Generic Clock operations |
| * -------------------------------------------------------------------- */ |
| |
| static void genclk_mode(struct clk *clk, int enabled) |
| { |
| u32 control; |
| |
| control = sm_readl(&system_manager, PM_GCCTRL + 4 * clk->index); |
| if (enabled) |
| control |= SM_BIT(CEN); |
| else |
| control &= ~SM_BIT(CEN); |
| sm_writel(&system_manager, PM_GCCTRL + 4 * clk->index, control); |
| } |
| |
| static unsigned long genclk_get_rate(struct clk *clk) |
| { |
| u32 control; |
| unsigned long div = 1; |
| |
| control = sm_readl(&system_manager, PM_GCCTRL + 4 * clk->index); |
| if (control & SM_BIT(DIVEN)) |
| div = 2 * (SM_BFEXT(DIV, control) + 1); |
| |
| return clk->parent->get_rate(clk->parent) / div; |
| } |
| |
| static long genclk_set_rate(struct clk *clk, unsigned long rate, int apply) |
| { |
| u32 control; |
| unsigned long parent_rate, actual_rate, div; |
| |
| parent_rate = clk->parent->get_rate(clk->parent); |
| control = sm_readl(&system_manager, PM_GCCTRL + 4 * clk->index); |
| |
| if (rate > 3 * parent_rate / 4) { |
| actual_rate = parent_rate; |
| control &= ~SM_BIT(DIVEN); |
| } else { |
| div = (parent_rate + rate) / (2 * rate) - 1; |
| control = SM_BFINS(DIV, div, control) | SM_BIT(DIVEN); |
| actual_rate = parent_rate / (2 * (div + 1)); |
| } |
| |
| printk("clk %s: new rate %lu (actual rate %lu)\n", |
| clk->name, rate, actual_rate); |
| |
| if (apply) |
| sm_writel(&system_manager, PM_GCCTRL + 4 * clk->index, |
| control); |
| |
| return actual_rate; |
| } |
| |
| int genclk_set_parent(struct clk *clk, struct clk *parent) |
| { |
| u32 control; |
| |
| printk("clk %s: new parent %s (was %s)\n", |
| clk->name, parent->name, clk->parent->name); |
| |
| control = sm_readl(&system_manager, PM_GCCTRL + 4 * clk->index); |
| |
| if (parent == &osc1 || parent == &pll1) |
| control |= SM_BIT(OSCSEL); |
| else if (parent == &osc0 || parent == &pll0) |
| control &= ~SM_BIT(OSCSEL); |
| else |
| return -EINVAL; |
| |
| if (parent == &pll0 || parent == &pll1) |
| control |= SM_BIT(PLLSEL); |
| else |
| control &= ~SM_BIT(PLLSEL); |
| |
| sm_writel(&system_manager, PM_GCCTRL + 4 * clk->index, control); |
| clk->parent = parent; |
| |
| return 0; |
| } |
| |
| static void __init genclk_init_parent(struct clk *clk) |
| { |
| u32 control; |
| struct clk *parent; |
| |
| BUG_ON(clk->index > 7); |
| |
| control = sm_readl(&system_manager, PM_GCCTRL + 4 * clk->index); |
| if (control & SM_BIT(OSCSEL)) |
| parent = (control & SM_BIT(PLLSEL)) ? &pll1 : &osc1; |
| else |
| parent = (control & SM_BIT(PLLSEL)) ? &pll0 : &osc0; |
| |
| clk->parent = parent; |
| } |
| |
| /* -------------------------------------------------------------------- |
| * System peripherals |
| * -------------------------------------------------------------------- */ |
| static struct resource sm_resource[] = { |
| PBMEM(0xfff00000), |
| NAMED_IRQ(19, "eim"), |
| NAMED_IRQ(20, "pm"), |
| NAMED_IRQ(21, "rtc"), |
| }; |
| struct platform_device at32_sm_device = { |
| .name = "sm", |
| .id = 0, |
| .resource = sm_resource, |
| .num_resources = ARRAY_SIZE(sm_resource), |
| }; |
| DEV_CLK(pclk, at32_sm, pbb, 0); |
| |
| static struct resource intc0_resource[] = { |
| PBMEM(0xfff00400), |
| }; |
| struct platform_device at32_intc0_device = { |
| .name = "intc", |
| .id = 0, |
| .resource = intc0_resource, |
| .num_resources = ARRAY_SIZE(intc0_resource), |
| }; |
| DEV_CLK(pclk, at32_intc0, pbb, 1); |
| |
| static struct clk ebi_clk = { |
| .name = "ebi", |
| .parent = &hsb_clk, |
| .mode = hsb_clk_mode, |
| .get_rate = hsb_clk_get_rate, |
| .users = 1, |
| }; |
| static struct clk hramc_clk = { |
| .name = "hramc", |
| .parent = &hsb_clk, |
| .mode = hsb_clk_mode, |
| .get_rate = hsb_clk_get_rate, |
| .users = 1, |
| }; |
| |
| static struct resource smc0_resource[] = { |
| PBMEM(0xfff03400), |
| }; |
| DEFINE_DEV(smc, 0); |
| DEV_CLK(pclk, smc0, pbb, 13); |
| DEV_CLK(mck, smc0, hsb, 0); |
| |
| static struct platform_device pdc_device = { |
| .name = "pdc", |
| .id = 0, |
| }; |
| DEV_CLK(hclk, pdc, hsb, 4); |
| DEV_CLK(pclk, pdc, pba, 16); |
| |
| static struct clk pico_clk = { |
| .name = "pico", |
| .parent = &cpu_clk, |
| .mode = cpu_clk_mode, |
| .get_rate = cpu_clk_get_rate, |
| .users = 1, |
| }; |
| |
| /* -------------------------------------------------------------------- |
| * PIO |
| * -------------------------------------------------------------------- */ |
| |
| static struct resource pio0_resource[] = { |
| PBMEM(0xffe02800), |
| IRQ(13), |
| }; |
| DEFINE_DEV(pio, 0); |
| DEV_CLK(mck, pio0, pba, 10); |
| |
| static struct resource pio1_resource[] = { |
| PBMEM(0xffe02c00), |
| IRQ(14), |
| }; |
| DEFINE_DEV(pio, 1); |
| DEV_CLK(mck, pio1, pba, 11); |
| |
| static struct resource pio2_resource[] = { |
| PBMEM(0xffe03000), |
| IRQ(15), |
| }; |
| DEFINE_DEV(pio, 2); |
| DEV_CLK(mck, pio2, pba, 12); |
| |
| static struct resource pio3_resource[] = { |
| PBMEM(0xffe03400), |
| IRQ(16), |
| }; |
| DEFINE_DEV(pio, 3); |
| DEV_CLK(mck, pio3, pba, 13); |
| |
| static struct resource pio4_resource[] = { |
| PBMEM(0xffe03800), |
| IRQ(17), |
| }; |
| DEFINE_DEV(pio, 4); |
| DEV_CLK(mck, pio4, pba, 14); |
| |
| void __init at32_add_system_devices(void) |
| { |
| system_manager.eim_first_irq = EIM_IRQ_BASE; |
| |
| platform_device_register(&at32_sm_device); |
| platform_device_register(&at32_intc0_device); |
| platform_device_register(&smc0_device); |
| platform_device_register(&pdc_device); |
| |
| platform_device_register(&pio0_device); |
| platform_device_register(&pio1_device); |
| platform_device_register(&pio2_device); |
| platform_device_register(&pio3_device); |
| platform_device_register(&pio4_device); |
| } |
| |
| /* -------------------------------------------------------------------- |
| * USART |
| * -------------------------------------------------------------------- */ |
| |
| static struct atmel_uart_data atmel_usart0_data = { |
| .use_dma_tx = 1, |
| .use_dma_rx = 1, |
| }; |
| static struct resource atmel_usart0_resource[] = { |
| PBMEM(0xffe00c00), |
| IRQ(6), |
| }; |
| DEFINE_DEV_DATA(atmel_usart, 0); |
| DEV_CLK(usart, atmel_usart0, pba, 4); |
| |
| static struct atmel_uart_data atmel_usart1_data = { |
| .use_dma_tx = 1, |
| .use_dma_rx = 1, |
| }; |
| static struct resource atmel_usart1_resource[] = { |
| PBMEM(0xffe01000), |
| IRQ(7), |
| }; |
| DEFINE_DEV_DATA(atmel_usart, 1); |
| DEV_CLK(usart, atmel_usart1, pba, 4); |
| |
| static struct atmel_uart_data atmel_usart2_data = { |
| .use_dma_tx = 1, |
| .use_dma_rx = 1, |
| }; |
| static struct resource atmel_usart2_resource[] = { |
| PBMEM(0xffe01400), |
| IRQ(8), |
| }; |
| DEFINE_DEV_DATA(atmel_usart, 2); |
| DEV_CLK(usart, atmel_usart2, pba, 5); |
| |
| static struct atmel_uart_data atmel_usart3_data = { |
| .use_dma_tx = 1, |
| .use_dma_rx = 1, |
| }; |
| static struct resource atmel_usart3_resource[] = { |
| PBMEM(0xffe01800), |
| IRQ(9), |
| }; |
| DEFINE_DEV_DATA(atmel_usart, 3); |
| DEV_CLK(usart, atmel_usart3, pba, 6); |
| |
| static inline void configure_usart0_pins(void) |
| { |
| select_peripheral(PA(8), PERIPH_B, 0); /* RXD */ |
| select_peripheral(PA(9), PERIPH_B, 0); /* TXD */ |
| } |
| |
| static inline void configure_usart1_pins(void) |
| { |
| select_peripheral(PA(17), PERIPH_A, 0); /* RXD */ |
| select_peripheral(PA(18), PERIPH_A, 0); /* TXD */ |
| } |
| |
| static inline void configure_usart2_pins(void) |
| { |
| select_peripheral(PB(26), PERIPH_B, 0); /* RXD */ |
| select_peripheral(PB(27), PERIPH_B, 0); /* TXD */ |
| } |
| |
| static inline void configure_usart3_pins(void) |
| { |
| select_peripheral(PB(18), PERIPH_B, 0); /* RXD */ |
| select_peripheral(PB(17), PERIPH_B, 0); /* TXD */ |
| } |
| |
| static struct platform_device *__initdata at32_usarts[4]; |
| |
| void __init at32_map_usart(unsigned int hw_id, unsigned int line) |
| { |
| struct platform_device *pdev; |
| |
| switch (hw_id) { |
| case 0: |
| pdev = &atmel_usart0_device; |
| configure_usart0_pins(); |
| break; |
| case 1: |
| pdev = &atmel_usart1_device; |
| configure_usart1_pins(); |
| break; |
| case 2: |
| pdev = &atmel_usart2_device; |
| configure_usart2_pins(); |
| break; |
| case 3: |
| pdev = &atmel_usart3_device; |
| configure_usart3_pins(); |
| break; |
| default: |
| return; |
| } |
| |
| if (PXSEG(pdev->resource[0].start) == P4SEG) { |
| /* Addresses in the P4 segment are permanently mapped 1:1 */ |
| struct atmel_uart_data *data = pdev->dev.platform_data; |
| data->regs = (void __iomem *)pdev->resource[0].start; |
| } |
| |
| pdev->id = line; |
| at32_usarts[line] = pdev; |
| } |
| |
| struct platform_device *__init at32_add_device_usart(unsigned int id) |
| { |
| platform_device_register(at32_usarts[id]); |
| return at32_usarts[id]; |
| } |
| |
| struct platform_device *atmel_default_console_device; |
| |
| void __init at32_setup_serial_console(unsigned int usart_id) |
| { |
| atmel_default_console_device = at32_usarts[usart_id]; |
| } |
| |
| /* -------------------------------------------------------------------- |
| * Ethernet |
| * -------------------------------------------------------------------- */ |
| |
| static struct eth_platform_data macb0_data; |
| static struct resource macb0_resource[] = { |
| PBMEM(0xfff01800), |
| IRQ(25), |
| }; |
| DEFINE_DEV_DATA(macb, 0); |
| DEV_CLK(hclk, macb0, hsb, 8); |
| DEV_CLK(pclk, macb0, pbb, 6); |
| |
| static struct eth_platform_data macb1_data; |
| static struct resource macb1_resource[] = { |
| PBMEM(0xfff01c00), |
| IRQ(26), |
| }; |
| DEFINE_DEV_DATA(macb, 1); |
| DEV_CLK(hclk, macb1, hsb, 9); |
| DEV_CLK(pclk, macb1, pbb, 7); |
| |
| struct platform_device *__init |
| at32_add_device_eth(unsigned int id, struct eth_platform_data *data) |
| { |
| struct platform_device *pdev; |
| |
| switch (id) { |
| case 0: |
| pdev = &macb0_device; |
| |
| select_peripheral(PC(3), PERIPH_A, 0); /* TXD0 */ |
| select_peripheral(PC(4), PERIPH_A, 0); /* TXD1 */ |
| select_peripheral(PC(7), PERIPH_A, 0); /* TXEN */ |
| select_peripheral(PC(8), PERIPH_A, 0); /* TXCK */ |
| select_peripheral(PC(9), PERIPH_A, 0); /* RXD0 */ |
| select_peripheral(PC(10), PERIPH_A, 0); /* RXD1 */ |
| select_peripheral(PC(13), PERIPH_A, 0); /* RXER */ |
| select_peripheral(PC(15), PERIPH_A, 0); /* RXDV */ |
| select_peripheral(PC(16), PERIPH_A, 0); /* MDC */ |
| select_peripheral(PC(17), PERIPH_A, 0); /* MDIO */ |
| |
| if (!data->is_rmii) { |
| select_peripheral(PC(0), PERIPH_A, 0); /* COL */ |
| select_peripheral(PC(1), PERIPH_A, 0); /* CRS */ |
| select_peripheral(PC(2), PERIPH_A, 0); /* TXER */ |
| select_peripheral(PC(5), PERIPH_A, 0); /* TXD2 */ |
| select_peripheral(PC(6), PERIPH_A, 0); /* TXD3 */ |
| select_peripheral(PC(11), PERIPH_A, 0); /* RXD2 */ |
| select_peripheral(PC(12), PERIPH_A, 0); /* RXD3 */ |
| select_peripheral(PC(14), PERIPH_A, 0); /* RXCK */ |
| select_peripheral(PC(18), PERIPH_A, 0); /* SPD */ |
| } |
| break; |
| |
| case 1: |
| pdev = &macb1_device; |
| |
| select_peripheral(PD(13), PERIPH_B, 0); /* TXD0 */ |
| select_peripheral(PD(14), PERIPH_B, 0); /* TXD1 */ |
| select_peripheral(PD(11), PERIPH_B, 0); /* TXEN */ |
| select_peripheral(PD(12), PERIPH_B, 0); /* TXCK */ |
| select_peripheral(PD(10), PERIPH_B, 0); /* RXD0 */ |
| select_peripheral(PD(6), PERIPH_B, 0); /* RXD1 */ |
| select_peripheral(PD(5), PERIPH_B, 0); /* RXER */ |
| select_peripheral(PD(4), PERIPH_B, 0); /* RXDV */ |
| select_peripheral(PD(3), PERIPH_B, 0); /* MDC */ |
| select_peripheral(PD(2), PERIPH_B, 0); /* MDIO */ |
| |
| if (!data->is_rmii) { |
| select_peripheral(PC(19), PERIPH_B, 0); /* COL */ |
| select_peripheral(PC(23), PERIPH_B, 0); /* CRS */ |
| select_peripheral(PC(26), PERIPH_B, 0); /* TXER */ |
| select_peripheral(PC(27), PERIPH_B, 0); /* TXD2 */ |
| select_peripheral(PC(28), PERIPH_B, 0); /* TXD3 */ |
| select_peripheral(PC(29), PERIPH_B, 0); /* RXD2 */ |
| select_peripheral(PC(30), PERIPH_B, 0); /* RXD3 */ |
| select_peripheral(PC(24), PERIPH_B, 0); /* RXCK */ |
| select_peripheral(PD(15), PERIPH_B, 0); /* SPD */ |
| } |
| break; |
| |
| default: |
| return NULL; |
| } |
| |
| memcpy(pdev->dev.platform_data, data, sizeof(struct eth_platform_data)); |
| platform_device_register(pdev); |
| |
| return pdev; |
| } |
| |
| /* -------------------------------------------------------------------- |
| * SPI |
| * -------------------------------------------------------------------- */ |
| static struct resource atmel_spi0_resource[] = { |
| PBMEM(0xffe00000), |
| IRQ(3), |
| }; |
| DEFINE_DEV(atmel_spi, 0); |
| DEV_CLK(spi_clk, atmel_spi0, pba, 0); |
| |
| static struct resource atmel_spi1_resource[] = { |
| PBMEM(0xffe00400), |
| IRQ(4), |
| }; |
| DEFINE_DEV(atmel_spi, 1); |
| DEV_CLK(spi_clk, atmel_spi1, pba, 1); |
| |
| static void __init |
| at32_spi_setup_slaves(unsigned int bus_num, struct spi_board_info *b, |
| unsigned int n, const u8 *pins) |
| { |
| unsigned int pin, mode; |
| |
| for (; n; n--, b++) { |
| b->bus_num = bus_num; |
| if (b->chip_select >= 4) |
| continue; |
| pin = (unsigned)b->controller_data; |
| if (!pin) { |
| pin = pins[b->chip_select]; |
| b->controller_data = (void *)pin; |
| } |
| mode = AT32_GPIOF_OUTPUT; |
| if (!(b->mode & SPI_CS_HIGH)) |
| mode |= AT32_GPIOF_HIGH; |
| at32_select_gpio(pin, mode); |
| } |
| } |
| |
| struct platform_device *__init |
| at32_add_device_spi(unsigned int id, struct spi_board_info *b, unsigned int n) |
| { |
| /* |
| * Manage the chipselects as GPIOs, normally using the same pins |
| * the SPI controller expects; but boards can use other pins. |
| */ |
| static u8 __initdata spi0_pins[] = |
| { GPIO_PIN_PA(3), GPIO_PIN_PA(4), |
| GPIO_PIN_PA(5), GPIO_PIN_PA(20), }; |
| static u8 __initdata spi1_pins[] = |
| { GPIO_PIN_PB(2), GPIO_PIN_PB(3), |
| GPIO_PIN_PB(4), GPIO_PIN_PA(27), }; |
| struct platform_device *pdev; |
| |
| switch (id) { |
| case 0: |
| pdev = &atmel_spi0_device; |
| select_peripheral(PA(0), PERIPH_A, 0); /* MISO */ |
| select_peripheral(PA(1), PERIPH_A, 0); /* MOSI */ |
| select_peripheral(PA(2), PERIPH_A, 0); /* SCK */ |
| at32_spi_setup_slaves(0, b, n, spi0_pins); |
| break; |
| |
| case 1: |
| pdev = &atmel_spi1_device; |
| select_peripheral(PB(0), PERIPH_B, 0); /* MISO */ |
| select_peripheral(PB(1), PERIPH_B, 0); /* MOSI */ |
| select_peripheral(PB(5), PERIPH_B, 0); /* SCK */ |
| at32_spi_setup_slaves(1, b, n, spi1_pins); |
| break; |
| |
| default: |
| return NULL; |
| } |
| |
| spi_register_board_info(b, n); |
| platform_device_register(pdev); |
| return pdev; |
| } |
| |
| /* -------------------------------------------------------------------- |
| * LCDC |
| * -------------------------------------------------------------------- */ |
| static struct lcdc_platform_data lcdc0_data; |
| static struct resource lcdc0_resource[] = { |
| { |
| .start = 0xff000000, |
| .end = 0xff000fff, |
| .flags = IORESOURCE_MEM, |
| }, |
| IRQ(1), |
| }; |
| DEFINE_DEV_DATA(lcdc, 0); |
| DEV_CLK(hclk, lcdc0, hsb, 7); |
| static struct clk lcdc0_pixclk = { |
| .name = "pixclk", |
| .dev = &lcdc0_device.dev, |
| .mode = genclk_mode, |
| .get_rate = genclk_get_rate, |
| .set_rate = genclk_set_rate, |
| .set_parent = genclk_set_parent, |
| .index = 7, |
| }; |
| |
| struct platform_device *__init |
| at32_add_device_lcdc(unsigned int id, struct lcdc_platform_data *data) |
| { |
| struct platform_device *pdev; |
| |
| switch (id) { |
| case 0: |
| pdev = &lcdc0_device; |
| select_peripheral(PC(19), PERIPH_A, 0); /* CC */ |
| select_peripheral(PC(20), PERIPH_A, 0); /* HSYNC */ |
| select_peripheral(PC(21), PERIPH_A, 0); /* PCLK */ |
| select_peripheral(PC(22), PERIPH_A, 0); /* VSYNC */ |
| select_peripheral(PC(23), PERIPH_A, 0); /* DVAL */ |
| select_peripheral(PC(24), PERIPH_A, 0); /* MODE */ |
| select_peripheral(PC(25), PERIPH_A, 0); /* PWR */ |
| select_peripheral(PC(26), PERIPH_A, 0); /* DATA0 */ |
| select_peripheral(PC(27), PERIPH_A, 0); /* DATA1 */ |
| select_peripheral(PC(28), PERIPH_A, 0); /* DATA2 */ |
| select_peripheral(PC(29), PERIPH_A, 0); /* DATA3 */ |
| select_peripheral(PC(30), PERIPH_A, 0); /* DATA4 */ |
| select_peripheral(PC(31), PERIPH_A, 0); /* DATA5 */ |
| select_peripheral(PD(0), PERIPH_A, 0); /* DATA6 */ |
| select_peripheral(PD(1), PERIPH_A, 0); /* DATA7 */ |
| select_peripheral(PD(2), PERIPH_A, 0); /* DATA8 */ |
| select_peripheral(PD(3), PERIPH_A, 0); /* DATA9 */ |
| select_peripheral(PD(4), PERIPH_A, 0); /* DATA10 */ |
| select_peripheral(PD(5), PERIPH_A, 0); /* DATA11 */ |
| select_peripheral(PD(6), PERIPH_A, 0); /* DATA12 */ |
| select_peripheral(PD(7), PERIPH_A, 0); /* DATA13 */ |
| select_peripheral(PD(8), PERIPH_A, 0); /* DATA14 */ |
| select_peripheral(PD(9), PERIPH_A, 0); /* DATA15 */ |
| select_peripheral(PD(10), PERIPH_A, 0); /* DATA16 */ |
| select_peripheral(PD(11), PERIPH_A, 0); /* DATA17 */ |
| select_peripheral(PD(12), PERIPH_A, 0); /* DATA18 */ |
| select_peripheral(PD(13), PERIPH_A, 0); /* DATA19 */ |
| select_peripheral(PD(14), PERIPH_A, 0); /* DATA20 */ |
| select_peripheral(PD(15), PERIPH_A, 0); /* DATA21 */ |
| select_peripheral(PD(16), PERIPH_A, 0); /* DATA22 */ |
| select_peripheral(PD(17), PERIPH_A, 0); /* DATA23 */ |
| |
| clk_set_parent(&lcdc0_pixclk, &pll0); |
| clk_set_rate(&lcdc0_pixclk, clk_get_rate(&pll0)); |
| break; |
| |
| default: |
| return NULL; |
| } |
| |
| memcpy(pdev->dev.platform_data, data, |
| sizeof(struct lcdc_platform_data)); |
| |
| platform_device_register(pdev); |
| return pdev; |
| } |
| |
| /* -------------------------------------------------------------------- |
| * GCLK |
| * -------------------------------------------------------------------- */ |
| static struct clk gclk0 = { |
| .name = "gclk0", |
| .mode = genclk_mode, |
| .get_rate = genclk_get_rate, |
| .set_rate = genclk_set_rate, |
| .set_parent = genclk_set_parent, |
| .index = 0, |
| }; |
| static struct clk gclk1 = { |
| .name = "gclk1", |
| .mode = genclk_mode, |
| .get_rate = genclk_get_rate, |
| .set_rate = genclk_set_rate, |
| .set_parent = genclk_set_parent, |
| .index = 1, |
| }; |
| static struct clk gclk2 = { |
| .name = "gclk2", |
| .mode = genclk_mode, |
| .get_rate = genclk_get_rate, |
| .set_rate = genclk_set_rate, |
| .set_parent = genclk_set_parent, |
| .index = 2, |
| }; |
| static struct clk gclk3 = { |
| .name = "gclk3", |
| .mode = genclk_mode, |
| .get_rate = genclk_get_rate, |
| .set_rate = genclk_set_rate, |
| .set_parent = genclk_set_parent, |
| .index = 3, |
| }; |
| static struct clk gclk4 = { |
| .name = "gclk4", |
| .mode = genclk_mode, |
| .get_rate = genclk_get_rate, |
| .set_rate = genclk_set_rate, |
| .set_parent = genclk_set_parent, |
| .index = 4, |
| }; |
| |
| struct clk *at32_clock_list[] = { |
| &osc32k, |
| &osc0, |
| &osc1, |
| &pll0, |
| &pll1, |
| &cpu_clk, |
| &hsb_clk, |
| &pba_clk, |
| &pbb_clk, |
| &at32_sm_pclk, |
| &at32_intc0_pclk, |
| &ebi_clk, |
| &hramc_clk, |
| &smc0_pclk, |
| &smc0_mck, |
| &pdc_hclk, |
| &pdc_pclk, |
| &pico_clk, |
| &pio0_mck, |
| &pio1_mck, |
| &pio2_mck, |
| &pio3_mck, |
| &pio4_mck, |
| &atmel_usart0_usart, |
| &atmel_usart1_usart, |
| &atmel_usart2_usart, |
| &atmel_usart3_usart, |
| &macb0_hclk, |
| &macb0_pclk, |
| &macb1_hclk, |
| &macb1_pclk, |
| &atmel_spi0_spi_clk, |
| &atmel_spi1_spi_clk, |
| &lcdc0_hclk, |
| &lcdc0_pixclk, |
| &gclk0, |
| &gclk1, |
| &gclk2, |
| &gclk3, |
| &gclk4, |
| }; |
| unsigned int at32_nr_clocks = ARRAY_SIZE(at32_clock_list); |
| |
| void __init at32_portmux_init(void) |
| { |
| at32_init_pio(&pio0_device); |
| at32_init_pio(&pio1_device); |
| at32_init_pio(&pio2_device); |
| at32_init_pio(&pio3_device); |
| at32_init_pio(&pio4_device); |
| } |
| |
| void __init at32_clock_init(void) |
| { |
| struct at32_sm *sm = &system_manager; |
| u32 cpu_mask = 0, hsb_mask = 0, pba_mask = 0, pbb_mask = 0; |
| int i; |
| |
| if (sm_readl(sm, PM_MCCTRL) & SM_BIT(PLLSEL)) |
| main_clock = &pll0; |
| else |
| main_clock = &osc0; |
| |
| if (sm_readl(sm, PM_PLL0) & SM_BIT(PLLOSC)) |
| pll0.parent = &osc1; |
| if (sm_readl(sm, PM_PLL1) & SM_BIT(PLLOSC)) |
| pll1.parent = &osc1; |
| |
| genclk_init_parent(&gclk0); |
| genclk_init_parent(&gclk1); |
| genclk_init_parent(&gclk2); |
| genclk_init_parent(&gclk3); |
| genclk_init_parent(&gclk4); |
| genclk_init_parent(&lcdc0_pixclk); |
| |
| /* |
| * Turn on all clocks that have at least one user already, and |
| * turn off everything else. We only do this for module |
| * clocks, and even though it isn't particularly pretty to |
| * check the address of the mode function, it should do the |
| * trick... |
| */ |
| for (i = 0; i < ARRAY_SIZE(at32_clock_list); i++) { |
| struct clk *clk = at32_clock_list[i]; |
| |
| if (clk->mode == &cpu_clk_mode) |
| cpu_mask |= 1 << clk->index; |
| else if (clk->mode == &hsb_clk_mode) |
| hsb_mask |= 1 << clk->index; |
| else if (clk->mode == &pba_clk_mode) |
| pba_mask |= 1 << clk->index; |
| else if (clk->mode == &pbb_clk_mode) |
| pbb_mask |= 1 << clk->index; |
| } |
| |
| sm_writel(sm, PM_CPU_MASK, cpu_mask); |
| sm_writel(sm, PM_HSB_MASK, hsb_mask); |
| sm_writel(sm, PM_PBA_MASK, pba_mask); |
| sm_writel(sm, PM_PBB_MASK, pbb_mask); |
| } |