| /* |
| * Aic7xxx register and scratch ram definitions. |
| * |
| * Copyright (c) 1994-2001 Justin T. Gibbs. |
| * Copyright (c) 2000-2001 Adaptec Inc. |
| * All rights reserved. |
| * |
| * Redistribution and use in source and binary forms, with or without |
| * modification, are permitted provided that the following conditions |
| * are met: |
| * 1. Redistributions of source code must retain the above copyright |
| * notice, this list of conditions, and the following disclaimer, |
| * without modification. |
| * 2. Redistributions in binary form must reproduce at minimum a disclaimer |
| * substantially similar to the "NO WARRANTY" disclaimer below |
| * ("Disclaimer") and any redistribution must be conditioned upon |
| * including a substantially similar Disclaimer requirement for further |
| * binary redistribution. |
| * 3. Neither the names of the above-listed copyright holders nor the names |
| * of any contributors may be used to endorse or promote products derived |
| * from this software without specific prior written permission. |
| * |
| * Alternatively, this software may be distributed under the terms of the |
| * GNU General Public License ("GPL") version 2 as published by the Free |
| * Software Foundation. |
| * |
| * NO WARRANTY |
| * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS |
| * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT |
| * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR |
| * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT |
| * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL |
| * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS |
| * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) |
| * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, |
| * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING |
| * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE |
| * POSSIBILITY OF SUCH DAMAGES. |
| * |
| * $FreeBSD$ |
| */ |
| VERSION = "$Id: //depot/aic7xxx/aic7xxx/aic7xxx.reg#40 $" |
| |
| /* |
| * This file is processed by the aic7xxx_asm utility for use in assembling |
| * firmware for the aic7xxx family of SCSI host adapters as well as to generate |
| * a C header file for use in the kernel portion of the Aic7xxx driver. |
| * |
| * All page numbers refer to the Adaptec AIC-7770 Data Book available from |
| * Adaptec's Technical Documents Department 1-800-934-2766 |
| */ |
| |
| /* |
| * Registers marked "dont_generate_debug_code" are not (yet) referenced |
| * from the driver code, and this keyword inhibit generation |
| * of debug code for them. |
| * |
| * REG_PRETTY_PRINT config will complain if dont_generate_debug_code |
| * is added to the register which is referenced in the driver. |
| * Unreferenced register with no dont_generate_debug_code will result |
| * in dead code. No warning is issued. |
| */ |
| |
| /* |
| * SCSI Sequence Control (p. 3-11). |
| * Each bit, when set starts a specific SCSI sequence on the bus |
| */ |
| register SCSISEQ { |
| address 0x000 |
| access_mode RW |
| field TEMODE 0x80 |
| field ENSELO 0x40 |
| field ENSELI 0x20 |
| field ENRSELI 0x10 |
| field ENAUTOATNO 0x08 |
| field ENAUTOATNI 0x04 |
| field ENAUTOATNP 0x02 |
| field SCSIRSTO 0x01 |
| } |
| |
| /* |
| * SCSI Transfer Control 0 Register (pp. 3-13). |
| * Controls the SCSI module data path. |
| */ |
| register SXFRCTL0 { |
| address 0x001 |
| access_mode RW |
| field DFON 0x80 |
| field DFPEXP 0x40 |
| field FAST20 0x20 |
| field CLRSTCNT 0x10 |
| field SPIOEN 0x08 |
| field SCAMEN 0x04 |
| field CLRCHN 0x02 |
| } |
| |
| /* |
| * SCSI Transfer Control 1 Register (pp. 3-14,15). |
| * Controls the SCSI module data path. |
| */ |
| register SXFRCTL1 { |
| address 0x002 |
| access_mode RW |
| field BITBUCKET 0x80 |
| field SWRAPEN 0x40 |
| field ENSPCHK 0x20 |
| mask STIMESEL 0x18 |
| field ENSTIMER 0x04 |
| field ACTNEGEN 0x02 |
| field STPWEN 0x01 /* Powered Termination */ |
| dont_generate_debug_code |
| } |
| |
| /* |
| * SCSI Control Signal Read Register (p. 3-15). |
| * Reads the actual state of the SCSI bus pins |
| */ |
| register SCSISIGI { |
| address 0x003 |
| access_mode RO |
| field CDI 0x80 |
| field IOI 0x40 |
| field MSGI 0x20 |
| field ATNI 0x10 |
| field SELI 0x08 |
| field BSYI 0x04 |
| field REQI 0x02 |
| field ACKI 0x01 |
| /* |
| * Possible phases in SCSISIGI |
| */ |
| mask PHASE_MASK CDI|IOI|MSGI |
| mask P_DATAOUT 0x00 |
| mask P_DATAIN IOI |
| mask P_DATAOUT_DT P_DATAOUT|MSGI |
| mask P_DATAIN_DT P_DATAIN|MSGI |
| mask P_COMMAND CDI |
| mask P_MESGOUT CDI|MSGI |
| mask P_STATUS CDI|IOI |
| mask P_MESGIN CDI|IOI|MSGI |
| } |
| |
| /* |
| * SCSI Control Signal Write Register (p. 3-16). |
| * Writing to this register modifies the control signals on the bus. Only |
| * those signals that are allowed in the current mode (Initiator/Target) are |
| * asserted. |
| */ |
| register SCSISIGO { |
| address 0x003 |
| access_mode WO |
| field CDO 0x80 |
| field IOO 0x40 |
| field MSGO 0x20 |
| field ATNO 0x10 |
| field SELO 0x08 |
| field BSYO 0x04 |
| field REQO 0x02 |
| field ACKO 0x01 |
| /* |
| * Possible phases to write into SCSISIG0 |
| */ |
| mask PHASE_MASK CDI|IOI|MSGI |
| mask P_DATAOUT 0x00 |
| mask P_DATAIN IOI |
| mask P_COMMAND CDI |
| mask P_MESGOUT CDI|MSGI |
| mask P_STATUS CDI|IOI |
| mask P_MESGIN CDI|IOI|MSGI |
| dont_generate_debug_code |
| } |
| |
| /* |
| * SCSI Rate Control (p. 3-17). |
| * Contents of this register determine the Synchronous SCSI data transfer |
| * rate and the maximum synchronous Req/Ack offset. An offset of 0 in the |
| * SOFS (3:0) bits disables synchronous data transfers. Any offset value |
| * greater than 0 enables synchronous transfers. |
| */ |
| register SCSIRATE { |
| address 0x004 |
| access_mode RW |
| field WIDEXFER 0x80 /* Wide transfer control */ |
| field ENABLE_CRC 0x40 /* CRC for D-Phases */ |
| field SINGLE_EDGE 0x10 /* Disable DT Transfers */ |
| mask SXFR 0x70 /* Sync transfer rate */ |
| mask SXFR_ULTRA2 0x0f /* Sync transfer rate */ |
| mask SOFS 0x0f /* Sync offset */ |
| } |
| |
| /* |
| * SCSI ID (p. 3-18). |
| * Contains the ID of the board and the current target on the |
| * selected channel. |
| */ |
| register SCSIID { |
| address 0x005 |
| access_mode RW |
| mask TID 0xf0 /* Target ID mask */ |
| mask TWIN_TID 0x70 |
| field TWIN_CHNLB 0x80 |
| mask OID 0x0f /* Our ID mask */ |
| /* |
| * SCSI Maximum Offset (p. 4-61 aic7890/91 Data Book) |
| * The aic7890/91 allow an offset of up to 127 transfers in both wide |
| * and narrow mode. |
| */ |
| alias SCSIOFFSET |
| mask SOFS_ULTRA2 0x7f /* Sync offset U2 chips */ |
| dont_generate_debug_code |
| } |
| |
| /* |
| * SCSI Latched Data (p. 3-19). |
| * Read/Write latches used to transfer data on the SCSI bus during |
| * Automatic or Manual PIO mode. SCSIDATH can be used for the |
| * upper byte of a 16bit wide asynchronouse data phase transfer. |
| */ |
| register SCSIDATL { |
| address 0x006 |
| access_mode RW |
| dont_generate_debug_code |
| } |
| |
| register SCSIDATH { |
| address 0x007 |
| access_mode RW |
| } |
| |
| /* |
| * SCSI Transfer Count (pp. 3-19,20) |
| * These registers count down the number of bytes transferred |
| * across the SCSI bus. The counter is decremented only once |
| * the data has been safely transferred. SDONE in SSTAT0 is |
| * set when STCNT goes to 0 |
| */ |
| register STCNT { |
| address 0x008 |
| size 3 |
| access_mode RW |
| dont_generate_debug_code |
| } |
| |
| /* ALT_MODE registers (Ultra2 and Ultra160 chips) */ |
| register SXFRCTL2 { |
| address 0x013 |
| access_mode RW |
| field AUTORSTDIS 0x10 |
| field CMDDMAEN 0x08 |
| mask ASYNC_SETUP 0x07 |
| } |
| |
| /* ALT_MODE register on Ultra160 chips */ |
| register OPTIONMODE { |
| address 0x008 |
| access_mode RW |
| count 2 |
| field AUTORATEEN 0x80 |
| field AUTOACKEN 0x40 |
| field ATNMGMNTEN 0x20 |
| field BUSFREEREV 0x10 |
| field EXPPHASEDIS 0x08 |
| field SCSIDATL_IMGEN 0x04 |
| field AUTO_MSGOUT_DE 0x02 |
| field DIS_MSGIN_DUALEDGE 0x01 |
| mask OPTIONMODE_DEFAULTS AUTO_MSGOUT_DE|DIS_MSGIN_DUALEDGE |
| dont_generate_debug_code |
| } |
| |
| /* ALT_MODE register on Ultra160 chips */ |
| register TARGCRCCNT { |
| address 0x00a |
| size 2 |
| access_mode RW |
| count 2 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Clear SCSI Interrupt 0 (p. 3-20) |
| * Writing a 1 to a bit clears the associated SCSI Interrupt in SSTAT0. |
| */ |
| register CLRSINT0 { |
| address 0x00b |
| access_mode WO |
| field CLRSELDO 0x40 |
| field CLRSELDI 0x20 |
| field CLRSELINGO 0x10 |
| field CLRSWRAP 0x08 |
| field CLRIOERR 0x08 /* Ultra2 Only */ |
| field CLRSPIORDY 0x02 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * SCSI Status 0 (p. 3-21) |
| * Contains one set of SCSI Interrupt codes |
| * These are most likely of interest to the sequencer |
| */ |
| register SSTAT0 { |
| address 0x00b |
| access_mode RO |
| field TARGET 0x80 /* Board acting as target */ |
| field SELDO 0x40 /* Selection Done */ |
| field SELDI 0x20 /* Board has been selected */ |
| field SELINGO 0x10 /* Selection In Progress */ |
| field SWRAP 0x08 /* 24bit counter wrap */ |
| field IOERR 0x08 /* LVD Tranceiver mode changed */ |
| field SDONE 0x04 /* STCNT = 0x000000 */ |
| field SPIORDY 0x02 /* SCSI PIO Ready */ |
| field DMADONE 0x01 /* DMA transfer completed */ |
| } |
| |
| /* |
| * Clear SCSI Interrupt 1 (p. 3-23) |
| * Writing a 1 to a bit clears the associated SCSI Interrupt in SSTAT1. |
| */ |
| register CLRSINT1 { |
| address 0x00c |
| access_mode WO |
| field CLRSELTIMEO 0x80 |
| field CLRATNO 0x40 |
| field CLRSCSIRSTI 0x20 |
| field CLRBUSFREE 0x08 |
| field CLRSCSIPERR 0x04 |
| field CLRPHASECHG 0x02 |
| field CLRREQINIT 0x01 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * SCSI Status 1 (p. 3-24) |
| */ |
| register SSTAT1 { |
| address 0x00c |
| access_mode RO |
| field SELTO 0x80 |
| field ATNTARG 0x40 |
| field SCSIRSTI 0x20 |
| field PHASEMIS 0x10 |
| field BUSFREE 0x08 |
| field SCSIPERR 0x04 |
| field PHASECHG 0x02 |
| field REQINIT 0x01 |
| } |
| |
| /* |
| * SCSI Status 2 (pp. 3-25,26) |
| */ |
| register SSTAT2 { |
| address 0x00d |
| access_mode RO |
| field OVERRUN 0x80 |
| field SHVALID 0x40 /* Shadow Layer non-zero */ |
| field EXP_ACTIVE 0x10 /* SCSI Expander Active */ |
| field CRCVALERR 0x08 /* CRC doesn't match (U3 only) */ |
| field CRCENDERR 0x04 /* No terminal CRC packet (U3 only) */ |
| field CRCREQERR 0x02 /* Illegal CRC packet req (U3 only) */ |
| field DUAL_EDGE_ERR 0x01 /* Incorrect data phase (U3 only) */ |
| mask SFCNT 0x1f |
| } |
| |
| /* |
| * SCSI Status 3 (p. 3-26) |
| */ |
| register SSTAT3 { |
| address 0x00e |
| access_mode RO |
| count 2 |
| mask SCSICNT 0xf0 |
| mask OFFCNT 0x0f |
| mask U2OFFCNT 0x7f |
| } |
| |
| /* |
| * SCSI ID for the aic7890/91 chips |
| */ |
| register SCSIID_ULTRA2 { |
| address 0x00f |
| access_mode RW |
| mask TID 0xf0 /* Target ID mask */ |
| mask OID 0x0f /* Our ID mask */ |
| dont_generate_debug_code |
| } |
| |
| /* |
| * SCSI Interrupt Mode 1 (p. 3-28) |
| * Setting any bit will enable the corresponding function |
| * in SIMODE0 to interrupt via the IRQ pin. |
| */ |
| register SIMODE0 { |
| address 0x010 |
| access_mode RW |
| count 2 |
| field ENSELDO 0x40 |
| field ENSELDI 0x20 |
| field ENSELINGO 0x10 |
| field ENSWRAP 0x08 |
| field ENIOERR 0x08 /* LVD Tranceiver mode changes */ |
| field ENSDONE 0x04 |
| field ENSPIORDY 0x02 |
| field ENDMADONE 0x01 |
| } |
| |
| /* |
| * SCSI Interrupt Mode 1 (pp. 3-28,29) |
| * Setting any bit will enable the corresponding function |
| * in SIMODE1 to interrupt via the IRQ pin. |
| */ |
| register SIMODE1 { |
| address 0x011 |
| access_mode RW |
| field ENSELTIMO 0x80 |
| field ENATNTARG 0x40 |
| field ENSCSIRST 0x20 |
| field ENPHASEMIS 0x10 |
| field ENBUSFREE 0x08 |
| field ENSCSIPERR 0x04 |
| field ENPHASECHG 0x02 |
| field ENREQINIT 0x01 |
| } |
| |
| /* |
| * SCSI Data Bus (High) (p. 3-29) |
| * This register reads data on the SCSI Data bus directly. |
| */ |
| register SCSIBUSL { |
| address 0x012 |
| access_mode RW |
| } |
| |
| register SCSIBUSH { |
| address 0x013 |
| access_mode RW |
| } |
| |
| /* |
| * SCSI/Host Address (p. 3-30) |
| * These registers hold the host address for the byte about to be |
| * transferred on the SCSI bus. They are counted up in the same |
| * manner as STCNT is counted down. SHADDR should always be used |
| * to determine the address of the last byte transferred since HADDR |
| * can be skewed by write ahead. |
| */ |
| register SHADDR { |
| address 0x014 |
| size 4 |
| access_mode RO |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Selection Timeout Timer (p. 3-30) |
| */ |
| register SELTIMER { |
| address 0x018 |
| access_mode RW |
| count 1 |
| field STAGE6 0x20 |
| field STAGE5 0x10 |
| field STAGE4 0x08 |
| field STAGE3 0x04 |
| field STAGE2 0x02 |
| field STAGE1 0x01 |
| alias TARGIDIN |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Selection/Reselection ID (p. 3-31) |
| * Upper four bits are the device id. The ONEBIT is set when the re/selecting |
| * device did not set its own ID. |
| */ |
| register SELID { |
| address 0x019 |
| access_mode RW |
| mask SELID_MASK 0xf0 |
| field ONEBIT 0x08 |
| dont_generate_debug_code |
| } |
| |
| register SCAMCTL { |
| address 0x01a |
| access_mode RW |
| field ENSCAMSELO 0x80 |
| field CLRSCAMSELID 0x40 |
| field ALTSTIM 0x20 |
| field DFLTTID 0x10 |
| mask SCAMLVL 0x03 |
| } |
| |
| /* |
| * Target Mode Selecting in ID bitmask (aic7890/91/96/97) |
| */ |
| register TARGID { |
| address 0x01b |
| size 2 |
| access_mode RW |
| count 14 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Serial Port I/O Cabability register (p. 4-95 aic7860 Data Book) |
| * Indicates if external logic has been attached to the chip to |
| * perform the tasks of accessing a serial eeprom, testing termination |
| * strength, and performing cable detection. On the aic7860, most of |
| * these features are handled on chip, but on the aic7855 an attached |
| * aic3800 does the grunt work. |
| */ |
| register SPIOCAP { |
| address 0x01b |
| access_mode RW |
| count 10 |
| field SOFT1 0x80 |
| field SOFT0 0x40 |
| field SOFTCMDEN 0x20 |
| field EXT_BRDCTL 0x10 /* External Board control */ |
| field SEEPROM 0x08 /* External serial eeprom logic */ |
| field EEPROM 0x04 /* Writable external BIOS ROM */ |
| field ROM 0x02 /* Logic for accessing external ROM */ |
| field SSPIOCPS 0x01 /* Termination and cable detection */ |
| dont_generate_debug_code |
| } |
| |
| register BRDCTL { |
| address 0x01d |
| count 11 |
| field BRDDAT7 0x80 |
| field BRDDAT6 0x40 |
| field BRDDAT5 0x20 |
| field BRDSTB 0x10 |
| field BRDCS 0x08 |
| field BRDRW 0x04 |
| field BRDCTL1 0x02 |
| field BRDCTL0 0x01 |
| /* 7890 Definitions */ |
| field BRDDAT4 0x10 |
| field BRDDAT3 0x08 |
| field BRDDAT2 0x04 |
| field BRDRW_ULTRA2 0x02 |
| field BRDSTB_ULTRA2 0x01 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Serial EEPROM Control (p. 4-92 in 7870 Databook) |
| * Controls the reading and writing of an external serial 1-bit |
| * EEPROM Device. In order to access the serial EEPROM, you must |
| * first set the SEEMS bit that generates a request to the memory |
| * port for access to the serial EEPROM device. When the memory |
| * port is not busy servicing another request, it reconfigures |
| * to allow access to the serial EEPROM. When this happens, SEERDY |
| * gets set high to verify that the memory port access has been |
| * granted. |
| * |
| * After successful arbitration for the memory port, the SEECS bit of |
| * the SEECTL register is connected to the chip select. The SEECK, |
| * SEEDO, and SEEDI are connected to the clock, data out, and data in |
| * lines respectively. The SEERDY bit of SEECTL is useful in that it |
| * gives us an 800 nsec timer. After a write to the SEECTL register, |
| * the SEERDY goes high 800 nsec later. The one exception to this is |
| * when we first request access to the memory port. The SEERDY goes |
| * high to signify that access has been granted and, for this case, has |
| * no implied timing. |
| * |
| * See 93cx6.c for detailed information on the protocol necessary to |
| * read the serial EEPROM. |
| */ |
| register SEECTL { |
| address 0x01e |
| count 11 |
| field EXTARBACK 0x80 |
| field EXTARBREQ 0x40 |
| field SEEMS 0x20 |
| field SEERDY 0x10 |
| field SEECS 0x08 |
| field SEECK 0x04 |
| field SEEDO 0x02 |
| field SEEDI 0x01 |
| dont_generate_debug_code |
| } |
| /* |
| * SCSI Block Control (p. 3-32) |
| * Controls Bus type and channel selection. In a twin channel configuration |
| * addresses 0x00-0x1e are gated to the appropriate channel based on this |
| * register. SELWIDE allows for the coexistence of 8bit and 16bit devices |
| * on a wide bus. |
| */ |
| register SBLKCTL { |
| address 0x01f |
| access_mode RW |
| field DIAGLEDEN 0x80 /* Aic78X0 only */ |
| field DIAGLEDON 0x40 /* Aic78X0 only */ |
| field AUTOFLUSHDIS 0x20 |
| field SELBUSB 0x08 |
| field ENAB40 0x08 /* LVD transceiver active */ |
| field ENAB20 0x04 /* SE/HVD transceiver active */ |
| field SELWIDE 0x02 |
| field XCVR 0x01 /* External transceiver active */ |
| } |
| |
| /* |
| * Sequencer Control (p. 3-33) |
| * Error detection mode and speed configuration |
| */ |
| register SEQCTL { |
| address 0x060 |
| access_mode RW |
| count 15 |
| field PERRORDIS 0x80 |
| field PAUSEDIS 0x40 |
| field FAILDIS 0x20 |
| field FASTMODE 0x10 |
| field BRKADRINTEN 0x08 |
| field STEP 0x04 |
| field SEQRESET 0x02 |
| field LOADRAM 0x01 |
| } |
| |
| /* |
| * Sequencer RAM Data (p. 3-34) |
| * Single byte window into the Scratch Ram area starting at the address |
| * specified by SEQADDR0 and SEQADDR1. To write a full word, simply write |
| * four bytes in succession. The SEQADDRs will increment after the most |
| * significant byte is written |
| */ |
| register SEQRAM { |
| address 0x061 |
| access_mode RW |
| count 2 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Sequencer Address Registers (p. 3-35) |
| * Only the first bit of SEQADDR1 holds addressing information |
| */ |
| register SEQADDR0 { |
| address 0x062 |
| access_mode RW |
| dont_generate_debug_code |
| } |
| |
| register SEQADDR1 { |
| address 0x063 |
| access_mode RW |
| count 8 |
| mask SEQADDR1_MASK 0x01 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Accumulator |
| * We cheat by passing arguments in the Accumulator up to the kernel driver |
| */ |
| register ACCUM { |
| address 0x064 |
| access_mode RW |
| accumulator |
| dont_generate_debug_code |
| } |
| |
| register SINDEX { |
| address 0x065 |
| access_mode RW |
| sindex |
| dont_generate_debug_code |
| } |
| |
| register DINDEX { |
| address 0x066 |
| access_mode RW |
| dont_generate_debug_code |
| } |
| |
| register ALLONES { |
| address 0x069 |
| access_mode RO |
| allones |
| dont_generate_debug_code |
| } |
| |
| register ALLZEROS { |
| address 0x06a |
| access_mode RO |
| allzeros |
| dont_generate_debug_code |
| } |
| |
| register NONE { |
| address 0x06a |
| access_mode WO |
| none |
| dont_generate_debug_code |
| } |
| |
| register FLAGS { |
| address 0x06b |
| access_mode RO |
| count 18 |
| field ZERO 0x02 |
| field CARRY 0x01 |
| dont_generate_debug_code |
| } |
| |
| register SINDIR { |
| address 0x06c |
| access_mode RO |
| dont_generate_debug_code |
| } |
| |
| register DINDIR { |
| address 0x06d |
| access_mode WO |
| dont_generate_debug_code |
| } |
| |
| register FUNCTION1 { |
| address 0x06e |
| access_mode RW |
| } |
| |
| register STACK { |
| address 0x06f |
| access_mode RO |
| count 5 |
| dont_generate_debug_code |
| } |
| |
| const STACK_SIZE 4 |
| |
| /* |
| * Board Control (p. 3-43) |
| */ |
| register BCTL { |
| address 0x084 |
| access_mode RW |
| field ACE 0x08 |
| field ENABLE 0x01 |
| } |
| |
| /* |
| * On the aic78X0 chips, Board Control is replaced by the DSCommand |
| * register (p. 4-64) |
| */ |
| register DSCOMMAND0 { |
| address 0x084 |
| access_mode RW |
| count 7 |
| field CACHETHEN 0x80 /* Cache Threshold enable */ |
| field DPARCKEN 0x40 /* Data Parity Check Enable */ |
| field MPARCKEN 0x20 /* Memory Parity Check Enable */ |
| field EXTREQLCK 0x10 /* External Request Lock */ |
| /* aic7890/91/96/97 only */ |
| field INTSCBRAMSEL 0x08 /* Internal SCB RAM Select */ |
| field RAMPS 0x04 /* External SCB RAM Present */ |
| field USCBSIZE32 0x02 /* Use 32byte SCB Page Size */ |
| field CIOPARCKEN 0x01 /* Internal bus parity error enable */ |
| dont_generate_debug_code |
| } |
| |
| register DSCOMMAND1 { |
| address 0x085 |
| access_mode RW |
| mask DSLATT 0xfc /* PCI latency timer (non-ultra2) */ |
| field HADDLDSEL1 0x02 /* Host Address Load Select Bits */ |
| field HADDLDSEL0 0x01 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Bus On/Off Time (p. 3-44) aic7770 only |
| */ |
| register BUSTIME { |
| address 0x085 |
| access_mode RW |
| count 2 |
| mask BOFF 0xf0 |
| mask BON 0x0f |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Bus Speed (p. 3-45) aic7770 only |
| */ |
| register BUSSPD { |
| address 0x086 |
| access_mode RW |
| count 2 |
| mask DFTHRSH 0xc0 |
| mask STBOFF 0x38 |
| mask STBON 0x07 |
| mask DFTHRSH_100 0xc0 |
| mask DFTHRSH_75 0x80 |
| dont_generate_debug_code |
| } |
| |
| /* aic7850/55/60/70/80/95 only */ |
| register DSPCISTATUS { |
| address 0x086 |
| count 4 |
| mask DFTHRSH_100 0xc0 |
| dont_generate_debug_code |
| } |
| |
| /* aic7890/91/96/97 only */ |
| register HS_MAILBOX { |
| address 0x086 |
| mask HOST_MAILBOX 0xF0 |
| mask SEQ_MAILBOX 0x0F |
| mask HOST_TQINPOS 0x80 /* Boundary at either 0 or 128 */ |
| dont_generate_debug_code |
| } |
| |
| const HOST_MAILBOX_SHIFT 4 |
| const SEQ_MAILBOX_SHIFT 0 |
| |
| /* |
| * Host Control (p. 3-47) R/W |
| * Overall host control of the device. |
| */ |
| register HCNTRL { |
| address 0x087 |
| access_mode RW |
| count 14 |
| field POWRDN 0x40 |
| field SWINT 0x10 |
| field IRQMS 0x08 |
| field PAUSE 0x04 |
| field INTEN 0x02 |
| field CHIPRST 0x01 |
| field CHIPRSTACK 0x01 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Host Address (p. 3-48) |
| * This register contains the address of the byte about |
| * to be transferred across the host bus. |
| */ |
| register HADDR { |
| address 0x088 |
| size 4 |
| access_mode RW |
| dont_generate_debug_code |
| } |
| |
| register HCNT { |
| address 0x08c |
| size 3 |
| access_mode RW |
| dont_generate_debug_code |
| } |
| |
| /* |
| * SCB Pointer (p. 3-49) |
| * Gate one of the SCBs into the SCBARRAY window. |
| */ |
| register SCBPTR { |
| address 0x090 |
| access_mode RW |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Interrupt Status (p. 3-50) |
| * Status for system interrupts |
| */ |
| register INTSTAT { |
| address 0x091 |
| access_mode RW |
| field BRKADRINT 0x08 |
| field SCSIINT 0x04 |
| field CMDCMPLT 0x02 |
| field SEQINT 0x01 |
| mask BAD_PHASE SEQINT /* unknown scsi bus phase */ |
| mask SEND_REJECT 0x10|SEQINT /* sending a message reject */ |
| mask PROTO_VIOLATION 0x20|SEQINT /* SCSI protocol violation */ |
| mask NO_MATCH 0x30|SEQINT /* no cmd match for reconnect */ |
| mask IGN_WIDE_RES 0x40|SEQINT /* Complex IGN Wide Res Msg */ |
| mask PDATA_REINIT 0x50|SEQINT /* |
| * Returned to data phase |
| * that requires data |
| * transfer pointers to be |
| * recalculated from the |
| * transfer residual. |
| */ |
| mask HOST_MSG_LOOP 0x60|SEQINT /* |
| * The bus is ready for the |
| * host to perform another |
| * message transaction. This |
| * mechanism is used for things |
| * like sync/wide negotiation |
| * that require a kernel based |
| * message state engine. |
| */ |
| mask BAD_STATUS 0x70|SEQINT /* Bad status from target */ |
| mask PERR_DETECTED 0x80|SEQINT /* |
| * Either the phase_lock |
| * or inb_next routine has |
| * noticed a parity error. |
| */ |
| mask DATA_OVERRUN 0x90|SEQINT /* |
| * Target attempted to write |
| * beyond the bounds of its |
| * command. |
| */ |
| mask MKMSG_FAILED 0xa0|SEQINT /* |
| * Target completed command |
| * without honoring our ATN |
| * request to issue a message. |
| */ |
| mask MISSED_BUSFREE 0xb0|SEQINT /* |
| * The sequencer never saw |
| * the bus go free after |
| * either a command complete |
| * or disconnect message. |
| */ |
| mask SCB_MISMATCH 0xc0|SEQINT /* |
| * Downloaded SCB's tag does |
| * not match the entry we |
| * intended to download. |
| */ |
| mask NO_FREE_SCB 0xd0|SEQINT /* |
| * get_free_or_disc_scb failed. |
| */ |
| mask OUT_OF_RANGE 0xe0|SEQINT |
| |
| mask SEQINT_MASK 0xf0|SEQINT /* SEQINT Status Codes */ |
| mask INT_PEND (BRKADRINT|SEQINT|SCSIINT|CMDCMPLT) |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Hard Error (p. 3-53) |
| * Reporting of catastrophic errors. You usually cannot recover from |
| * these without a full board reset. |
| */ |
| register ERROR { |
| address 0x092 |
| access_mode RO |
| count 26 |
| field CIOPARERR 0x80 /* Ultra2 only */ |
| field PCIERRSTAT 0x40 /* PCI only */ |
| field MPARERR 0x20 /* PCI only */ |
| field DPARERR 0x10 /* PCI only */ |
| field SQPARERR 0x08 |
| field ILLOPCODE 0x04 |
| field ILLSADDR 0x02 |
| field ILLHADDR 0x01 |
| } |
| |
| /* |
| * Clear Interrupt Status (p. 3-52) |
| */ |
| register CLRINT { |
| address 0x092 |
| access_mode WO |
| count 24 |
| field CLRPARERR 0x10 /* PCI only */ |
| field CLRBRKADRINT 0x08 |
| field CLRSCSIINT 0x04 |
| field CLRCMDINT 0x02 |
| field CLRSEQINT 0x01 |
| dont_generate_debug_code |
| } |
| |
| register DFCNTRL { |
| address 0x093 |
| access_mode RW |
| field PRELOADEN 0x80 /* aic7890 only */ |
| field WIDEODD 0x40 |
| field SCSIEN 0x20 |
| field SDMAEN 0x10 |
| field SDMAENACK 0x10 |
| field HDMAEN 0x08 |
| field HDMAENACK 0x08 |
| field DIRECTION 0x04 |
| field FIFOFLUSH 0x02 |
| field FIFORESET 0x01 |
| } |
| |
| register DFSTATUS { |
| address 0x094 |
| access_mode RO |
| field PRELOAD_AVAIL 0x80 |
| field DFCACHETH 0x40 |
| field FIFOQWDEMP 0x20 |
| field MREQPEND 0x10 |
| field HDONE 0x08 |
| field DFTHRESH 0x04 |
| field FIFOFULL 0x02 |
| field FIFOEMP 0x01 |
| } |
| |
| register DFWADDR { |
| address 0x95 |
| access_mode RW |
| dont_generate_debug_code |
| } |
| |
| register DFRADDR { |
| address 0x97 |
| access_mode RW |
| } |
| |
| register DFDAT { |
| address 0x099 |
| access_mode RW |
| dont_generate_debug_code |
| } |
| |
| /* |
| * SCB Auto Increment (p. 3-59) |
| * Byte offset into the SCB Array and an optional bit to allow auto |
| * incrementing of the address during download and upload operations |
| */ |
| register SCBCNT { |
| address 0x09a |
| access_mode RW |
| count 1 |
| field SCBAUTO 0x80 |
| mask SCBCNT_MASK 0x1f |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Queue In FIFO (p. 3-60) |
| * Input queue for queued SCBs (commands that the seqencer has yet to start) |
| */ |
| register QINFIFO { |
| address 0x09b |
| access_mode RW |
| count 12 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Queue In Count (p. 3-60) |
| * Number of queued SCBs |
| */ |
| register QINCNT { |
| address 0x09c |
| access_mode RO |
| } |
| |
| /* |
| * Queue Out FIFO (p. 3-61) |
| * Queue of SCBs that have completed and await the host |
| */ |
| register QOUTFIFO { |
| address 0x09d |
| access_mode WO |
| count 7 |
| dont_generate_debug_code |
| } |
| |
| register CRCCONTROL1 { |
| address 0x09d |
| access_mode RW |
| count 3 |
| field CRCONSEEN 0x80 |
| field CRCVALCHKEN 0x40 |
| field CRCENDCHKEN 0x20 |
| field CRCREQCHKEN 0x10 |
| field TARGCRCENDEN 0x08 |
| field TARGCRCCNTEN 0x04 |
| dont_generate_debug_code |
| } |
| |
| |
| /* |
| * Queue Out Count (p. 3-61) |
| * Number of queued SCBs in the Out FIFO |
| */ |
| register QOUTCNT { |
| address 0x09e |
| access_mode RO |
| } |
| |
| register SCSIPHASE { |
| address 0x09e |
| access_mode RO |
| field STATUS_PHASE 0x20 |
| field COMMAND_PHASE 0x10 |
| field MSG_IN_PHASE 0x08 |
| field MSG_OUT_PHASE 0x04 |
| field DATA_IN_PHASE 0x02 |
| field DATA_OUT_PHASE 0x01 |
| mask DATA_PHASE_MASK 0x03 |
| } |
| |
| /* |
| * Special Function |
| */ |
| register SFUNCT { |
| address 0x09f |
| access_mode RW |
| count 4 |
| field ALT_MODE 0x80 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * SCB Definition (p. 5-4) |
| */ |
| scb { |
| address 0x0a0 |
| size 64 |
| |
| SCB_CDB_PTR { |
| size 4 |
| alias SCB_RESIDUAL_DATACNT |
| alias SCB_CDB_STORE |
| dont_generate_debug_code |
| } |
| SCB_RESIDUAL_SGPTR { |
| size 4 |
| dont_generate_debug_code |
| } |
| SCB_SCSI_STATUS { |
| size 1 |
| dont_generate_debug_code |
| } |
| SCB_TARGET_PHASES { |
| size 1 |
| dont_generate_debug_code |
| } |
| SCB_TARGET_DATA_DIR { |
| size 1 |
| dont_generate_debug_code |
| } |
| SCB_TARGET_ITAG { |
| size 1 |
| dont_generate_debug_code |
| } |
| SCB_DATAPTR { |
| size 4 |
| dont_generate_debug_code |
| } |
| SCB_DATACNT { |
| /* |
| * The last byte is really the high address bits for |
| * the data address. |
| */ |
| size 4 |
| field SG_LAST_SEG 0x80 /* In the fourth byte */ |
| mask SG_HIGH_ADDR_BITS 0x7F /* In the fourth byte */ |
| dont_generate_debug_code |
| } |
| SCB_SGPTR { |
| size 4 |
| field SG_RESID_VALID 0x04 /* In the first byte */ |
| field SG_FULL_RESID 0x02 /* In the first byte */ |
| field SG_LIST_NULL 0x01 /* In the first byte */ |
| dont_generate_debug_code |
| } |
| SCB_CONTROL { |
| size 1 |
| field TARGET_SCB 0x80 |
| field STATUS_RCVD 0x80 |
| field DISCENB 0x40 |
| field TAG_ENB 0x20 |
| field MK_MESSAGE 0x10 |
| field ULTRAENB 0x08 |
| field DISCONNECTED 0x04 |
| mask SCB_TAG_TYPE 0x03 |
| } |
| SCB_SCSIID { |
| size 1 |
| field TWIN_CHNLB 0x80 |
| mask TWIN_TID 0x70 |
| mask TID 0xf0 |
| mask OID 0x0f |
| } |
| SCB_LUN { |
| field SCB_XFERLEN_ODD 0x80 |
| mask LID 0x3f |
| size 1 |
| } |
| SCB_TAG { |
| size 1 |
| } |
| SCB_CDB_LEN { |
| size 1 |
| dont_generate_debug_code |
| } |
| SCB_SCSIRATE { |
| size 1 |
| dont_generate_debug_code |
| } |
| SCB_SCSIOFFSET { |
| size 1 |
| count 1 |
| dont_generate_debug_code |
| } |
| SCB_NEXT { |
| size 1 |
| dont_generate_debug_code |
| } |
| SCB_64_SPARE { |
| size 16 |
| } |
| SCB_64_BTT { |
| size 16 |
| dont_generate_debug_code |
| } |
| } |
| |
| const SCB_UPLOAD_SIZE 32 |
| const SCB_DOWNLOAD_SIZE 32 |
| const SCB_DOWNLOAD_SIZE_64 48 |
| |
| const SG_SIZEOF 0x08 /* sizeof(struct ahc_dma) */ |
| |
| /* --------------------- AHA-2840-only definitions -------------------- */ |
| |
| register SEECTL_2840 { |
| address 0x0c0 |
| access_mode RW |
| count 2 |
| field CS_2840 0x04 |
| field CK_2840 0x02 |
| field DO_2840 0x01 |
| dont_generate_debug_code |
| } |
| |
| register STATUS_2840 { |
| address 0x0c1 |
| access_mode RW |
| count 4 |
| field EEPROM_TF 0x80 |
| mask BIOS_SEL 0x60 |
| mask ADSEL 0x1e |
| field DI_2840 0x01 |
| dont_generate_debug_code |
| } |
| |
| /* --------------------- AIC-7870-only definitions -------------------- */ |
| |
| register CCHADDR { |
| address 0x0E0 |
| size 8 |
| dont_generate_debug_code |
| } |
| |
| register CCHCNT { |
| address 0x0E8 |
| dont_generate_debug_code |
| } |
| |
| register CCSGRAM { |
| address 0x0E9 |
| dont_generate_debug_code |
| } |
| |
| register CCSGADDR { |
| address 0x0EA |
| dont_generate_debug_code |
| } |
| |
| register CCSGCTL { |
| address 0x0EB |
| field CCSGDONE 0x80 |
| field CCSGEN 0x08 |
| field SG_FETCH_NEEDED 0x02 /* Bit used for software state */ |
| field CCSGRESET 0x01 |
| dont_generate_debug_code |
| } |
| |
| register CCSCBCNT { |
| address 0xEF |
| count 1 |
| dont_generate_debug_code |
| } |
| |
| register CCSCBCTL { |
| address 0x0EE |
| field CCSCBDONE 0x80 |
| field ARRDONE 0x40 /* SCB Array prefetch done */ |
| field CCARREN 0x10 |
| field CCSCBEN 0x08 |
| field CCSCBDIR 0x04 |
| field CCSCBRESET 0x01 |
| dont_generate_debug_code |
| } |
| |
| register CCSCBADDR { |
| address 0x0ED |
| dont_generate_debug_code |
| } |
| |
| register CCSCBRAM { |
| address 0xEC |
| dont_generate_debug_code |
| } |
| |
| /* |
| * SCB bank address (7895/7896/97 only) |
| */ |
| register SCBBADDR { |
| address 0x0F0 |
| access_mode RW |
| count 3 |
| dont_generate_debug_code |
| } |
| |
| register CCSCBPTR { |
| address 0x0F1 |
| dont_generate_debug_code |
| } |
| |
| register HNSCB_QOFF { |
| address 0x0F4 |
| count 4 |
| dont_generate_debug_code |
| } |
| |
| register SNSCB_QOFF { |
| address 0x0F6 |
| dont_generate_debug_code |
| } |
| |
| register SDSCB_QOFF { |
| address 0x0F8 |
| dont_generate_debug_code |
| } |
| |
| register QOFF_CTLSTA { |
| address 0x0FA |
| field SCB_AVAIL 0x40 |
| field SNSCB_ROLLOVER 0x20 |
| field SDSCB_ROLLOVER 0x10 |
| mask SCB_QSIZE 0x07 |
| mask SCB_QSIZE_256 0x06 |
| dont_generate_debug_code |
| } |
| |
| register DFF_THRSH { |
| address 0x0FB |
| mask WR_DFTHRSH 0x70 |
| mask RD_DFTHRSH 0x07 |
| mask RD_DFTHRSH_MIN 0x00 |
| mask RD_DFTHRSH_25 0x01 |
| mask RD_DFTHRSH_50 0x02 |
| mask RD_DFTHRSH_63 0x03 |
| mask RD_DFTHRSH_75 0x04 |
| mask RD_DFTHRSH_85 0x05 |
| mask RD_DFTHRSH_90 0x06 |
| mask RD_DFTHRSH_MAX 0x07 |
| mask WR_DFTHRSH_MIN 0x00 |
| mask WR_DFTHRSH_25 0x10 |
| mask WR_DFTHRSH_50 0x20 |
| mask WR_DFTHRSH_63 0x30 |
| mask WR_DFTHRSH_75 0x40 |
| mask WR_DFTHRSH_85 0x50 |
| mask WR_DFTHRSH_90 0x60 |
| mask WR_DFTHRSH_MAX 0x70 |
| count 4 |
| dont_generate_debug_code |
| } |
| |
| register SG_CACHE_PRE { |
| access_mode WO |
| address 0x0fc |
| mask SG_ADDR_MASK 0xf8 |
| field LAST_SEG 0x02 |
| field LAST_SEG_DONE 0x01 |
| dont_generate_debug_code |
| } |
| |
| register SG_CACHE_SHADOW { |
| access_mode RO |
| address 0x0fc |
| mask SG_ADDR_MASK 0xf8 |
| field LAST_SEG 0x02 |
| field LAST_SEG_DONE 0x01 |
| dont_generate_debug_code |
| } |
| /* ---------------------- Scratch RAM Offsets ------------------------- */ |
| /* These offsets are either to values that are initialized by the board's |
| * BIOS or are specified by the sequencer code. |
| * |
| * The host adapter card (at least the BIOS) uses 20-2f for SCSI |
| * device information, 32-33 and 5a-5f as well. As it turns out, the |
| * BIOS trashes 20-2f, writing the synchronous negotiation results |
| * on top of the BIOS values, so we re-use those for our per-target |
| * scratchspace (actually a value that can be copied directly into |
| * SCSIRATE). The kernel driver will enable synchronous negotiation |
| * for all targets that have a value other than 0 in the lower four |
| * bits of the target scratch space. This should work regardless of |
| * whether the bios has been installed. |
| */ |
| |
| scratch_ram { |
| address 0x020 |
| size 58 |
| |
| /* |
| * 1 byte per target starting at this address for configuration values |
| */ |
| BUSY_TARGETS { |
| alias TARG_SCSIRATE |
| size 16 |
| dont_generate_debug_code |
| } |
| /* |
| * Bit vector of targets that have ULTRA enabled as set by |
| * the BIOS. The Sequencer relies on a per-SCB field to |
| * control whether to enable Ultra transfers or not. During |
| * initialization, we read this field and reuse it for 2 |
| * entries in the busy target table. |
| */ |
| ULTRA_ENB { |
| alias CMDSIZE_TABLE |
| size 2 |
| count 2 |
| dont_generate_debug_code |
| } |
| /* |
| * Bit vector of targets that have disconnection disabled as set by |
| * the BIOS. The Sequencer relies in a per-SCB field to control the |
| * disconnect priveldge. During initialization, we read this field |
| * and reuse it for 2 entries in the busy target table. |
| */ |
| DISC_DSB { |
| size 2 |
| count 6 |
| dont_generate_debug_code |
| } |
| CMDSIZE_TABLE_TAIL { |
| size 4 |
| } |
| /* |
| * Partial transfer past cacheline end to be |
| * transferred using an extra S/G. |
| */ |
| MWI_RESIDUAL { |
| size 1 |
| dont_generate_debug_code |
| } |
| /* |
| * SCBID of the next SCB to be started by the controller. |
| */ |
| NEXT_QUEUED_SCB { |
| size 1 |
| dont_generate_debug_code |
| } |
| /* |
| * Single byte buffer used to designate the type or message |
| * to send to a target. |
| */ |
| MSG_OUT { |
| size 1 |
| dont_generate_debug_code |
| } |
| /* Parameters for DMA Logic */ |
| DMAPARAMS { |
| size 1 |
| count 12 |
| field PRELOADEN 0x80 |
| field WIDEODD 0x40 |
| field SCSIEN 0x20 |
| field SDMAEN 0x10 |
| field SDMAENACK 0x10 |
| field HDMAEN 0x08 |
| field HDMAENACK 0x08 |
| field DIRECTION 0x04 /* Set indicates PCI->SCSI */ |
| field FIFOFLUSH 0x02 |
| field FIFORESET 0x01 |
| dont_generate_debug_code |
| } |
| SEQ_FLAGS { |
| size 1 |
| field NOT_IDENTIFIED 0x80 |
| field NO_CDB_SENT 0x40 |
| field TARGET_CMD_IS_TAGGED 0x40 |
| field DPHASE 0x20 |
| /* Target flags */ |
| field TARG_CMD_PENDING 0x10 |
| field CMDPHASE_PENDING 0x08 |
| field DPHASE_PENDING 0x04 |
| field SPHASE_PENDING 0x02 |
| field NO_DISCONNECT 0x01 |
| } |
| /* |
| * Temporary storage for the |
| * target/channel/lun of a |
| * reconnecting target |
| */ |
| SAVED_SCSIID { |
| size 1 |
| dont_generate_debug_code |
| } |
| SAVED_LUN { |
| size 1 |
| dont_generate_debug_code |
| } |
| /* |
| * The last bus phase as seen by the sequencer. |
| */ |
| LASTPHASE { |
| size 1 |
| field CDI 0x80 |
| field IOI 0x40 |
| field MSGI 0x20 |
| mask PHASE_MASK CDI|IOI|MSGI |
| mask P_DATAOUT 0x00 |
| mask P_DATAIN IOI |
| mask P_COMMAND CDI |
| mask P_MESGOUT CDI|MSGI |
| mask P_STATUS CDI|IOI |
| mask P_MESGIN CDI|IOI|MSGI |
| mask P_BUSFREE 0x01 |
| } |
| /* |
| * head of list of SCBs awaiting |
| * selection |
| */ |
| WAITING_SCBH { |
| size 1 |
| dont_generate_debug_code |
| } |
| /* |
| * head of list of SCBs that are |
| * disconnected. Used for SCB |
| * paging. |
| */ |
| DISCONNECTED_SCBH { |
| size 1 |
| dont_generate_debug_code |
| } |
| /* |
| * head of list of SCBs that are |
| * not in use. Used for SCB paging. |
| */ |
| FREE_SCBH { |
| size 1 |
| dont_generate_debug_code |
| } |
| /* |
| * head of list of SCBs that have |
| * completed but have not been |
| * put into the qoutfifo. |
| */ |
| COMPLETE_SCBH { |
| size 1 |
| } |
| /* |
| * Address of the hardware scb array in the host. |
| */ |
| HSCB_ADDR { |
| size 4 |
| dont_generate_debug_code |
| } |
| /* |
| * Base address of our shared data with the kernel driver in host |
| * memory. This includes the qoutfifo and target mode |
| * incoming command queue. |
| */ |
| SHARED_DATA_ADDR { |
| size 4 |
| dont_generate_debug_code |
| } |
| KERNEL_QINPOS { |
| size 1 |
| dont_generate_debug_code |
| } |
| QINPOS { |
| size 1 |
| dont_generate_debug_code |
| } |
| QOUTPOS { |
| size 1 |
| dont_generate_debug_code |
| } |
| /* |
| * Kernel and sequencer offsets into the queue of |
| * incoming target mode command descriptors. The |
| * queue is full when the KERNEL_TQINPOS == TQINPOS. |
| */ |
| KERNEL_TQINPOS { |
| size 1 |
| dont_generate_debug_code |
| } |
| TQINPOS { |
| size 1 |
| dont_generate_debug_code |
| } |
| ARG_1 { |
| size 1 |
| count 1 |
| mask SEND_MSG 0x80 |
| mask SEND_SENSE 0x40 |
| mask SEND_REJ 0x20 |
| mask MSGOUT_PHASEMIS 0x10 |
| mask EXIT_MSG_LOOP 0x08 |
| mask CONT_MSG_LOOP 0x04 |
| mask CONT_TARG_SESSION 0x02 |
| alias RETURN_1 |
| dont_generate_debug_code |
| } |
| ARG_2 { |
| size 1 |
| alias RETURN_2 |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Snapshot of MSG_OUT taken after each message is sent. |
| */ |
| LAST_MSG { |
| size 1 |
| alias TARG_IMMEDIATE_SCB |
| dont_generate_debug_code |
| } |
| |
| /* |
| * Sequences the kernel driver has okayed for us. This allows |
| * the driver to do things like prevent initiator or target |
| * operations. |
| */ |
| SCSISEQ_TEMPLATE { |
| size 1 |
| field ENSELO 0x40 |
| field ENSELI 0x20 |
| field ENRSELI 0x10 |
| field ENAUTOATNO 0x08 |
| field ENAUTOATNI 0x04 |
| field ENAUTOATNP 0x02 |
| dont_generate_debug_code |
| } |
| } |
| |
| scratch_ram { |
| address 0x056 |
| size 4 |
| /* |
| * These scratch ram locations are initialized by the 274X BIOS. |
| * We reuse them after capturing the BIOS settings during |
| * initialization. |
| */ |
| |
| /* |
| * The initiator specified tag for this target mode transaction. |
| */ |
| HA_274_BIOSGLOBAL { |
| size 1 |
| field HA_274_EXTENDED_TRANS 0x01 |
| alias INITIATOR_TAG |
| count 1 |
| dont_generate_debug_code |
| } |
| |
| SEQ_FLAGS2 { |
| size 1 |
| field SCB_DMA 0x01 |
| field TARGET_MSG_PENDING 0x02 |
| dont_generate_debug_code |
| } |
| } |
| |
| scratch_ram { |
| address 0x05a |
| size 6 |
| /* |
| * These are reserved registers in the card's scratch ram on the 2742. |
| * The EISA configuraiton chip is mapped here. On Rev E. of the |
| * aic7770, the sequencer can use this area for scratch, but the |
| * host cannot directly access these registers. On later chips, this |
| * area can be read and written by both the host and the sequencer. |
| * Even on later chips, many of these locations are initialized by |
| * the BIOS. |
| */ |
| SCSICONF { |
| size 1 |
| count 12 |
| field TERM_ENB 0x80 |
| field RESET_SCSI 0x40 |
| field ENSPCHK 0x20 |
| mask HSCSIID 0x07 /* our SCSI ID */ |
| mask HWSCSIID 0x0f /* our SCSI ID if Wide Bus */ |
| dont_generate_debug_code |
| } |
| INTDEF { |
| address 0x05c |
| size 1 |
| count 1 |
| field EDGE_TRIG 0x80 |
| mask VECTOR 0x0f |
| dont_generate_debug_code |
| } |
| HOSTCONF { |
| address 0x05d |
| size 1 |
| count 1 |
| dont_generate_debug_code |
| } |
| HA_274_BIOSCTRL { |
| address 0x05f |
| size 1 |
| count 1 |
| mask BIOSMODE 0x30 |
| mask BIOSDISABLED 0x30 |
| field CHANNEL_B_PRIMARY 0x08 |
| dont_generate_debug_code |
| } |
| } |
| |
| scratch_ram { |
| address 0x070 |
| size 16 |
| |
| /* |
| * Per target SCSI offset values for Ultra2 controllers. |
| */ |
| TARG_OFFSET { |
| size 16 |
| count 1 |
| dont_generate_debug_code |
| } |
| } |
| |
| const TID_SHIFT 4 |
| const SCB_LIST_NULL 0xff |
| const TARGET_CMD_CMPLT 0xfe |
| |
| const CCSGADDR_MAX 0x80 |
| const CCSGRAM_MAXSEGS 16 |
| |
| /* WDTR Message values */ |
| const BUS_8_BIT 0x00 |
| const BUS_16_BIT 0x01 |
| const BUS_32_BIT 0x02 |
| |
| /* Offset maximums */ |
| const MAX_OFFSET_8BIT 0x0f |
| const MAX_OFFSET_16BIT 0x08 |
| const MAX_OFFSET_ULTRA2 0x7f |
| const MAX_OFFSET 0x7f |
| const HOST_MSG 0xff |
| |
| /* Target mode command processing constants */ |
| const CMD_GROUP_CODE_SHIFT 0x05 |
| |
| const STATUS_BUSY 0x08 |
| const STATUS_QUEUE_FULL 0x28 |
| const TARGET_DATA_IN 1 |
| |
| /* |
| * Downloaded (kernel inserted) constants |
| */ |
| /* Offsets into the SCBID array where different data is stored */ |
| const QOUTFIFO_OFFSET download |
| const QINFIFO_OFFSET download |
| const CACHESIZE_MASK download |
| const INVERTED_CACHESIZE_MASK download |
| const SG_PREFETCH_CNT download |
| const SG_PREFETCH_ALIGN_MASK download |
| const SG_PREFETCH_ADDR_MASK download |