| /* |
| * bcm2835 sdhost driver. |
| * |
| * The 2835 has two SD controllers: The Arasan sdhci controller |
| * (supported by the iproc driver) and a custom sdhost controller |
| * (supported by this driver). |
| * |
| * The sdhci controller supports both sdcard and sdio. The sdhost |
| * controller supports the sdcard only, but has better performance. |
| * Also note that the rpi3 has sdio wifi, so driving the sdcard with |
| * the sdhost controller allows to use the sdhci controller for wifi |
| * support. |
| * |
| * The configuration is done by devicetree via pin muxing. Both |
| * SD controller are available on the same pins (2 pin groups = pin 22 |
| * to 27 + pin 48 to 53). So it's possible to use both SD controllers |
| * at the same time with different pin groups. |
| * |
| * Author: Phil Elwell <phil@raspberrypi.org> |
| * Copyright (C) 2015-2016 Raspberry Pi (Trading) Ltd. |
| * |
| * Based on |
| * mmc-bcm2835.c by Gellert Weisz |
| * which is, in turn, based on |
| * sdhci-bcm2708.c by Broadcom |
| * sdhci-bcm2835.c by Stephen Warren and Oleksandr Tymoshenko |
| * sdhci.c and sdhci-pci.c by Pierre Ossman |
| * |
| * This program is free software; you can redistribute it and/or modify it |
| * under the terms and conditions of the GNU General Public License, |
| * version 2, as published by the Free Software Foundation. |
| * |
| * This program is distributed in the hope it will be useful, but WITHOUT |
| * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or |
| * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for |
| * more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program. If not, see <http://www.gnu.org/licenses/>. |
| */ |
| #include <linux/clk.h> |
| #include <linux/delay.h> |
| #include <linux/device.h> |
| #include <linux/dmaengine.h> |
| #include <linux/dma-mapping.h> |
| #include <linux/err.h> |
| #include <linux/highmem.h> |
| #include <linux/interrupt.h> |
| #include <linux/io.h> |
| #include <linux/iopoll.h> |
| #include <linux/module.h> |
| #include <linux/of_address.h> |
| #include <linux/of_irq.h> |
| #include <linux/platform_device.h> |
| #include <linux/scatterlist.h> |
| #include <linux/time.h> |
| #include <linux/workqueue.h> |
| |
| #include <linux/mmc/host.h> |
| #include <linux/mmc/mmc.h> |
| #include <linux/mmc/sd.h> |
| |
| #define SDCMD 0x00 /* Command to SD card - 16 R/W */ |
| #define SDARG 0x04 /* Argument to SD card - 32 R/W */ |
| #define SDTOUT 0x08 /* Start value for timeout counter - 32 R/W */ |
| #define SDCDIV 0x0c /* Start value for clock divider - 11 R/W */ |
| #define SDRSP0 0x10 /* SD card response (31:0) - 32 R */ |
| #define SDRSP1 0x14 /* SD card response (63:32) - 32 R */ |
| #define SDRSP2 0x18 /* SD card response (95:64) - 32 R */ |
| #define SDRSP3 0x1c /* SD card response (127:96) - 32 R */ |
| #define SDHSTS 0x20 /* SD host status - 11 R/W */ |
| #define SDVDD 0x30 /* SD card power control - 1 R/W */ |
| #define SDEDM 0x34 /* Emergency Debug Mode - 13 R/W */ |
| #define SDHCFG 0x38 /* Host configuration - 2 R/W */ |
| #define SDHBCT 0x3c /* Host byte count (debug) - 32 R/W */ |
| #define SDDATA 0x40 /* Data to/from SD card - 32 R/W */ |
| #define SDHBLC 0x50 /* Host block count (SDIO/SDHC) - 9 R/W */ |
| |
| #define SDCMD_NEW_FLAG 0x8000 |
| #define SDCMD_FAIL_FLAG 0x4000 |
| #define SDCMD_BUSYWAIT 0x800 |
| #define SDCMD_NO_RESPONSE 0x400 |
| #define SDCMD_LONG_RESPONSE 0x200 |
| #define SDCMD_WRITE_CMD 0x80 |
| #define SDCMD_READ_CMD 0x40 |
| #define SDCMD_CMD_MASK 0x3f |
| |
| #define SDCDIV_MAX_CDIV 0x7ff |
| |
| #define SDHSTS_BUSY_IRPT 0x400 |
| #define SDHSTS_BLOCK_IRPT 0x200 |
| #define SDHSTS_SDIO_IRPT 0x100 |
| #define SDHSTS_REW_TIME_OUT 0x80 |
| #define SDHSTS_CMD_TIME_OUT 0x40 |
| #define SDHSTS_CRC16_ERROR 0x20 |
| #define SDHSTS_CRC7_ERROR 0x10 |
| #define SDHSTS_FIFO_ERROR 0x08 |
| /* Reserved */ |
| /* Reserved */ |
| #define SDHSTS_DATA_FLAG 0x01 |
| |
| #define SDHSTS_TRANSFER_ERROR_MASK (SDHSTS_CRC7_ERROR | \ |
| SDHSTS_CRC16_ERROR | \ |
| SDHSTS_REW_TIME_OUT | \ |
| SDHSTS_FIFO_ERROR) |
| |
| #define SDHSTS_ERROR_MASK (SDHSTS_CMD_TIME_OUT | \ |
| SDHSTS_TRANSFER_ERROR_MASK) |
| |
| #define SDHCFG_BUSY_IRPT_EN BIT(10) |
| #define SDHCFG_BLOCK_IRPT_EN BIT(8) |
| #define SDHCFG_SDIO_IRPT_EN BIT(5) |
| #define SDHCFG_DATA_IRPT_EN BIT(4) |
| #define SDHCFG_SLOW_CARD BIT(3) |
| #define SDHCFG_WIDE_EXT_BUS BIT(2) |
| #define SDHCFG_WIDE_INT_BUS BIT(1) |
| #define SDHCFG_REL_CMD_LINE BIT(0) |
| |
| #define SDVDD_POWER_OFF 0 |
| #define SDVDD_POWER_ON 1 |
| |
| #define SDEDM_FORCE_DATA_MODE BIT(19) |
| #define SDEDM_CLOCK_PULSE BIT(20) |
| #define SDEDM_BYPASS BIT(21) |
| |
| #define SDEDM_WRITE_THRESHOLD_SHIFT 9 |
| #define SDEDM_READ_THRESHOLD_SHIFT 14 |
| #define SDEDM_THRESHOLD_MASK 0x1f |
| |
| #define SDEDM_FSM_MASK 0xf |
| #define SDEDM_FSM_IDENTMODE 0x0 |
| #define SDEDM_FSM_DATAMODE 0x1 |
| #define SDEDM_FSM_READDATA 0x2 |
| #define SDEDM_FSM_WRITEDATA 0x3 |
| #define SDEDM_FSM_READWAIT 0x4 |
| #define SDEDM_FSM_READCRC 0x5 |
| #define SDEDM_FSM_WRITECRC 0x6 |
| #define SDEDM_FSM_WRITEWAIT1 0x7 |
| #define SDEDM_FSM_POWERDOWN 0x8 |
| #define SDEDM_FSM_POWERUP 0x9 |
| #define SDEDM_FSM_WRITESTART1 0xa |
| #define SDEDM_FSM_WRITESTART2 0xb |
| #define SDEDM_FSM_GENPULSES 0xc |
| #define SDEDM_FSM_WRITEWAIT2 0xd |
| #define SDEDM_FSM_STARTPOWDOWN 0xf |
| |
| #define SDDATA_FIFO_WORDS 16 |
| |
| #define FIFO_READ_THRESHOLD 4 |
| #define FIFO_WRITE_THRESHOLD 4 |
| #define SDDATA_FIFO_PIO_BURST 8 |
| |
| #define PIO_THRESHOLD 1 /* Maximum block count for PIO (0 = always DMA) */ |
| |
| struct bcm2835_host { |
| spinlock_t lock; |
| struct mutex mutex; |
| |
| void __iomem *ioaddr; |
| u32 phys_addr; |
| |
| struct mmc_host *mmc; |
| struct platform_device *pdev; |
| |
| int clock; /* Current clock speed */ |
| unsigned int max_clk; /* Max possible freq */ |
| struct work_struct dma_work; |
| struct delayed_work timeout_work; /* Timer for timeouts */ |
| struct sg_mapping_iter sg_miter; /* SG state for PIO */ |
| unsigned int blocks; /* remaining PIO blocks */ |
| int irq; /* Device IRQ */ |
| |
| u32 ns_per_fifo_word; |
| |
| /* cached registers */ |
| u32 hcfg; |
| u32 cdiv; |
| |
| struct mmc_request *mrq; /* Current request */ |
| struct mmc_command *cmd; /* Current command */ |
| struct mmc_data *data; /* Current data request */ |
| bool data_complete:1;/* Data finished before cmd */ |
| bool use_busy:1; /* Wait for busy interrupt */ |
| bool use_sbc:1; /* Send CMD23 */ |
| |
| /* for threaded irq handler */ |
| bool irq_block; |
| bool irq_busy; |
| bool irq_data; |
| |
| /* DMA part */ |
| struct dma_chan *dma_chan_rxtx; |
| struct dma_chan *dma_chan; |
| struct dma_slave_config dma_cfg_rx; |
| struct dma_slave_config dma_cfg_tx; |
| struct dma_async_tx_descriptor *dma_desc; |
| u32 dma_dir; |
| u32 drain_words; |
| struct page *drain_page; |
| u32 drain_offset; |
| bool use_dma; |
| }; |
| |
| static void bcm2835_dumpcmd(struct bcm2835_host *host, struct mmc_command *cmd, |
| const char *label) |
| { |
| struct device *dev = &host->pdev->dev; |
| |
| if (!cmd) |
| return; |
| |
| dev_dbg(dev, "%c%s op %d arg 0x%x flags 0x%x - resp %08x %08x %08x %08x, err %d\n", |
| (cmd == host->cmd) ? '>' : ' ', |
| label, cmd->opcode, cmd->arg, cmd->flags, |
| cmd->resp[0], cmd->resp[1], cmd->resp[2], cmd->resp[3], |
| cmd->error); |
| } |
| |
| static void bcm2835_dumpregs(struct bcm2835_host *host) |
| { |
| struct mmc_request *mrq = host->mrq; |
| struct device *dev = &host->pdev->dev; |
| |
| if (mrq) { |
| bcm2835_dumpcmd(host, mrq->sbc, "sbc"); |
| bcm2835_dumpcmd(host, mrq->cmd, "cmd"); |
| if (mrq->data) { |
| dev_dbg(dev, "data blocks %x blksz %x - err %d\n", |
| mrq->data->blocks, |
| mrq->data->blksz, |
| mrq->data->error); |
| } |
| bcm2835_dumpcmd(host, mrq->stop, "stop"); |
| } |
| |
| dev_dbg(dev, "=========== REGISTER DUMP ===========\n"); |
| dev_dbg(dev, "SDCMD 0x%08x\n", readl(host->ioaddr + SDCMD)); |
| dev_dbg(dev, "SDARG 0x%08x\n", readl(host->ioaddr + SDARG)); |
| dev_dbg(dev, "SDTOUT 0x%08x\n", readl(host->ioaddr + SDTOUT)); |
| dev_dbg(dev, "SDCDIV 0x%08x\n", readl(host->ioaddr + SDCDIV)); |
| dev_dbg(dev, "SDRSP0 0x%08x\n", readl(host->ioaddr + SDRSP0)); |
| dev_dbg(dev, "SDRSP1 0x%08x\n", readl(host->ioaddr + SDRSP1)); |
| dev_dbg(dev, "SDRSP2 0x%08x\n", readl(host->ioaddr + SDRSP2)); |
| dev_dbg(dev, "SDRSP3 0x%08x\n", readl(host->ioaddr + SDRSP3)); |
| dev_dbg(dev, "SDHSTS 0x%08x\n", readl(host->ioaddr + SDHSTS)); |
| dev_dbg(dev, "SDVDD 0x%08x\n", readl(host->ioaddr + SDVDD)); |
| dev_dbg(dev, "SDEDM 0x%08x\n", readl(host->ioaddr + SDEDM)); |
| dev_dbg(dev, "SDHCFG 0x%08x\n", readl(host->ioaddr + SDHCFG)); |
| dev_dbg(dev, "SDHBCT 0x%08x\n", readl(host->ioaddr + SDHBCT)); |
| dev_dbg(dev, "SDHBLC 0x%08x\n", readl(host->ioaddr + SDHBLC)); |
| dev_dbg(dev, "===========================================\n"); |
| } |
| |
| static void bcm2835_reset_internal(struct bcm2835_host *host) |
| { |
| u32 temp; |
| |
| writel(SDVDD_POWER_OFF, host->ioaddr + SDVDD); |
| writel(0, host->ioaddr + SDCMD); |
| writel(0, host->ioaddr + SDARG); |
| writel(0xf00000, host->ioaddr + SDTOUT); |
| writel(0, host->ioaddr + SDCDIV); |
| writel(0x7f8, host->ioaddr + SDHSTS); /* Write 1s to clear */ |
| writel(0, host->ioaddr + SDHCFG); |
| writel(0, host->ioaddr + SDHBCT); |
| writel(0, host->ioaddr + SDHBLC); |
| |
| /* Limit fifo usage due to silicon bug */ |
| temp = readl(host->ioaddr + SDEDM); |
| temp &= ~((SDEDM_THRESHOLD_MASK << SDEDM_READ_THRESHOLD_SHIFT) | |
| (SDEDM_THRESHOLD_MASK << SDEDM_WRITE_THRESHOLD_SHIFT)); |
| temp |= (FIFO_READ_THRESHOLD << SDEDM_READ_THRESHOLD_SHIFT) | |
| (FIFO_WRITE_THRESHOLD << SDEDM_WRITE_THRESHOLD_SHIFT); |
| writel(temp, host->ioaddr + SDEDM); |
| msleep(20); |
| writel(SDVDD_POWER_ON, host->ioaddr + SDVDD); |
| msleep(20); |
| host->clock = 0; |
| writel(host->hcfg, host->ioaddr + SDHCFG); |
| writel(host->cdiv, host->ioaddr + SDCDIV); |
| } |
| |
| static void bcm2835_reset(struct mmc_host *mmc) |
| { |
| struct bcm2835_host *host = mmc_priv(mmc); |
| |
| if (host->dma_chan) |
| dmaengine_terminate_sync(host->dma_chan); |
| host->dma_chan = NULL; |
| bcm2835_reset_internal(host); |
| } |
| |
| static void bcm2835_finish_command(struct bcm2835_host *host); |
| |
| static void bcm2835_wait_transfer_complete(struct bcm2835_host *host) |
| { |
| int timediff; |
| u32 alternate_idle; |
| |
| alternate_idle = (host->mrq->data->flags & MMC_DATA_READ) ? |
| SDEDM_FSM_READWAIT : SDEDM_FSM_WRITESTART1; |
| |
| timediff = 0; |
| |
| while (1) { |
| u32 edm, fsm; |
| |
| edm = readl(host->ioaddr + SDEDM); |
| fsm = edm & SDEDM_FSM_MASK; |
| |
| if ((fsm == SDEDM_FSM_IDENTMODE) || |
| (fsm == SDEDM_FSM_DATAMODE)) |
| break; |
| if (fsm == alternate_idle) { |
| writel(edm | SDEDM_FORCE_DATA_MODE, |
| host->ioaddr + SDEDM); |
| break; |
| } |
| |
| timediff++; |
| if (timediff == 100000) { |
| dev_err(&host->pdev->dev, |
| "wait_transfer_complete - still waiting after %d retries\n", |
| timediff); |
| bcm2835_dumpregs(host); |
| host->mrq->data->error = -ETIMEDOUT; |
| return; |
| } |
| cpu_relax(); |
| } |
| } |
| |
| static void bcm2835_dma_complete(void *param) |
| { |
| struct bcm2835_host *host = param; |
| |
| schedule_work(&host->dma_work); |
| } |
| |
| static void bcm2835_transfer_block_pio(struct bcm2835_host *host, bool is_read) |
| { |
| unsigned long flags; |
| size_t blksize; |
| unsigned long wait_max; |
| |
| blksize = host->data->blksz; |
| |
| wait_max = jiffies + msecs_to_jiffies(500); |
| |
| local_irq_save(flags); |
| |
| while (blksize) { |
| int copy_words; |
| u32 hsts = 0; |
| size_t len; |
| u32 *buf; |
| |
| if (!sg_miter_next(&host->sg_miter)) { |
| host->data->error = -EINVAL; |
| break; |
| } |
| |
| len = min(host->sg_miter.length, blksize); |
| if (len % 4) { |
| host->data->error = -EINVAL; |
| break; |
| } |
| |
| blksize -= len; |
| host->sg_miter.consumed = len; |
| |
| buf = (u32 *)host->sg_miter.addr; |
| |
| copy_words = len / 4; |
| |
| while (copy_words) { |
| int burst_words, words; |
| u32 edm; |
| |
| burst_words = min(SDDATA_FIFO_PIO_BURST, copy_words); |
| edm = readl(host->ioaddr + SDEDM); |
| if (is_read) |
| words = ((edm >> 4) & 0x1f); |
| else |
| words = SDDATA_FIFO_WORDS - ((edm >> 4) & 0x1f); |
| |
| if (words < burst_words) { |
| int fsm_state = (edm & SDEDM_FSM_MASK); |
| struct device *dev = &host->pdev->dev; |
| |
| if ((is_read && |
| (fsm_state != SDEDM_FSM_READDATA && |
| fsm_state != SDEDM_FSM_READWAIT && |
| fsm_state != SDEDM_FSM_READCRC)) || |
| (!is_read && |
| (fsm_state != SDEDM_FSM_WRITEDATA && |
| fsm_state != SDEDM_FSM_WRITESTART1 && |
| fsm_state != SDEDM_FSM_WRITESTART2))) { |
| hsts = readl(host->ioaddr + SDHSTS); |
| dev_err(dev, "fsm %x, hsts %08x\n", |
| fsm_state, hsts); |
| if (hsts & SDHSTS_ERROR_MASK) |
| break; |
| } |
| |
| if (time_after(jiffies, wait_max)) { |
| dev_err(dev, "PIO %s timeout - EDM %08x\n", |
| is_read ? "read" : "write", |
| edm); |
| hsts = SDHSTS_REW_TIME_OUT; |
| break; |
| } |
| ndelay((burst_words - words) * |
| host->ns_per_fifo_word); |
| continue; |
| } else if (words > copy_words) { |
| words = copy_words; |
| } |
| |
| copy_words -= words; |
| |
| while (words) { |
| if (is_read) |
| *(buf++) = readl(host->ioaddr + SDDATA); |
| else |
| writel(*(buf++), host->ioaddr + SDDATA); |
| words--; |
| } |
| } |
| |
| if (hsts & SDHSTS_ERROR_MASK) |
| break; |
| } |
| |
| sg_miter_stop(&host->sg_miter); |
| |
| local_irq_restore(flags); |
| } |
| |
| static void bcm2835_transfer_pio(struct bcm2835_host *host) |
| { |
| struct device *dev = &host->pdev->dev; |
| u32 sdhsts; |
| bool is_read; |
| |
| is_read = (host->data->flags & MMC_DATA_READ) != 0; |
| bcm2835_transfer_block_pio(host, is_read); |
| |
| sdhsts = readl(host->ioaddr + SDHSTS); |
| if (sdhsts & (SDHSTS_CRC16_ERROR | |
| SDHSTS_CRC7_ERROR | |
| SDHSTS_FIFO_ERROR)) { |
| dev_err(dev, "%s transfer error - HSTS %08x\n", |
| is_read ? "read" : "write", sdhsts); |
| host->data->error = -EILSEQ; |
| } else if ((sdhsts & (SDHSTS_CMD_TIME_OUT | |
| SDHSTS_REW_TIME_OUT))) { |
| dev_err(dev, "%s timeout error - HSTS %08x\n", |
| is_read ? "read" : "write", sdhsts); |
| host->data->error = -ETIMEDOUT; |
| } |
| } |
| |
| static |
| void bcm2835_prepare_dma(struct bcm2835_host *host, struct mmc_data *data) |
| { |
| int len, dir_data, dir_slave; |
| struct dma_async_tx_descriptor *desc = NULL; |
| struct dma_chan *dma_chan; |
| |
| dma_chan = host->dma_chan_rxtx; |
| if (data->flags & MMC_DATA_READ) { |
| dir_data = DMA_FROM_DEVICE; |
| dir_slave = DMA_DEV_TO_MEM; |
| } else { |
| dir_data = DMA_TO_DEVICE; |
| dir_slave = DMA_MEM_TO_DEV; |
| } |
| |
| /* The block doesn't manage the FIFO DREQs properly for |
| * multi-block transfers, so don't attempt to DMA the final |
| * few words. Unfortunately this requires the final sg entry |
| * to be trimmed. N.B. This code demands that the overspill |
| * is contained in a single sg entry. |
| */ |
| |
| host->drain_words = 0; |
| if ((data->blocks > 1) && (dir_data == DMA_FROM_DEVICE)) { |
| struct scatterlist *sg; |
| u32 len; |
| int i; |
| |
| len = min((u32)(FIFO_READ_THRESHOLD - 1) * 4, |
| (u32)data->blocks * data->blksz); |
| |
| for_each_sg(data->sg, sg, data->sg_len, i) { |
| if (sg_is_last(sg)) { |
| WARN_ON(sg->length < len); |
| sg->length -= len; |
| host->drain_page = sg_page(sg); |
| host->drain_offset = sg->offset + sg->length; |
| } |
| } |
| host->drain_words = len / 4; |
| } |
| |
| /* The parameters have already been validated, so this will not fail */ |
| (void)dmaengine_slave_config(dma_chan, |
| (dir_data == DMA_FROM_DEVICE) ? |
| &host->dma_cfg_rx : |
| &host->dma_cfg_tx); |
| |
| len = dma_map_sg(dma_chan->device->dev, data->sg, data->sg_len, |
| dir_data); |
| |
| if (len > 0) { |
| desc = dmaengine_prep_slave_sg(dma_chan, data->sg, |
| len, dir_slave, |
| DMA_PREP_INTERRUPT | |
| DMA_CTRL_ACK); |
| } |
| |
| if (desc) { |
| desc->callback = bcm2835_dma_complete; |
| desc->callback_param = host; |
| host->dma_desc = desc; |
| host->dma_chan = dma_chan; |
| host->dma_dir = dir_data; |
| } |
| } |
| |
| static void bcm2835_start_dma(struct bcm2835_host *host) |
| { |
| dmaengine_submit(host->dma_desc); |
| dma_async_issue_pending(host->dma_chan); |
| } |
| |
| static void bcm2835_set_transfer_irqs(struct bcm2835_host *host) |
| { |
| u32 all_irqs = SDHCFG_DATA_IRPT_EN | SDHCFG_BLOCK_IRPT_EN | |
| SDHCFG_BUSY_IRPT_EN; |
| |
| if (host->dma_desc) { |
| host->hcfg = (host->hcfg & ~all_irqs) | |
| SDHCFG_BUSY_IRPT_EN; |
| } else { |
| host->hcfg = (host->hcfg & ~all_irqs) | |
| SDHCFG_DATA_IRPT_EN | |
| SDHCFG_BUSY_IRPT_EN; |
| } |
| |
| writel(host->hcfg, host->ioaddr + SDHCFG); |
| } |
| |
| static |
| void bcm2835_prepare_data(struct bcm2835_host *host, struct mmc_command *cmd) |
| { |
| struct mmc_data *data = cmd->data; |
| |
| WARN_ON(host->data); |
| |
| host->data = data; |
| if (!data) |
| return; |
| |
| host->data_complete = false; |
| host->data->bytes_xfered = 0; |
| |
| if (!host->dma_desc) { |
| /* Use PIO */ |
| int flags = SG_MITER_ATOMIC; |
| |
| if (data->flags & MMC_DATA_READ) |
| flags |= SG_MITER_TO_SG; |
| else |
| flags |= SG_MITER_FROM_SG; |
| sg_miter_start(&host->sg_miter, data->sg, data->sg_len, flags); |
| host->blocks = data->blocks; |
| } |
| |
| bcm2835_set_transfer_irqs(host); |
| |
| writel(data->blksz, host->ioaddr + SDHBCT); |
| writel(data->blocks, host->ioaddr + SDHBLC); |
| } |
| |
| static u32 bcm2835_read_wait_sdcmd(struct bcm2835_host *host, u32 max_ms) |
| { |
| struct device *dev = &host->pdev->dev; |
| u32 value; |
| int ret; |
| |
| ret = readl_poll_timeout(host->ioaddr + SDCMD, value, |
| !(value & SDCMD_NEW_FLAG), 1, 10); |
| if (ret == -ETIMEDOUT) |
| /* if it takes a while make poll interval bigger */ |
| ret = readl_poll_timeout(host->ioaddr + SDCMD, value, |
| !(value & SDCMD_NEW_FLAG), |
| 10, max_ms * 1000); |
| if (ret == -ETIMEDOUT) |
| dev_err(dev, "%s: timeout (%d ms)\n", __func__, max_ms); |
| |
| return value; |
| } |
| |
| static void bcm2835_finish_request(struct bcm2835_host *host) |
| { |
| struct dma_chan *terminate_chan = NULL; |
| struct mmc_request *mrq; |
| |
| cancel_delayed_work(&host->timeout_work); |
| |
| mrq = host->mrq; |
| |
| host->mrq = NULL; |
| host->cmd = NULL; |
| host->data = NULL; |
| |
| host->dma_desc = NULL; |
| terminate_chan = host->dma_chan; |
| host->dma_chan = NULL; |
| |
| if (terminate_chan) { |
| int err = dmaengine_terminate_all(terminate_chan); |
| |
| if (err) |
| dev_err(&host->pdev->dev, |
| "failed to terminate DMA (%d)\n", err); |
| } |
| |
| mmc_request_done(host->mmc, mrq); |
| } |
| |
| static |
| bool bcm2835_send_command(struct bcm2835_host *host, struct mmc_command *cmd) |
| { |
| struct device *dev = &host->pdev->dev; |
| u32 sdcmd, sdhsts; |
| unsigned long timeout; |
| |
| WARN_ON(host->cmd); |
| |
| sdcmd = bcm2835_read_wait_sdcmd(host, 100); |
| if (sdcmd & SDCMD_NEW_FLAG) { |
| dev_err(dev, "previous command never completed.\n"); |
| bcm2835_dumpregs(host); |
| cmd->error = -EILSEQ; |
| bcm2835_finish_request(host); |
| return false; |
| } |
| |
| if (!cmd->data && cmd->busy_timeout > 9000) |
| timeout = DIV_ROUND_UP(cmd->busy_timeout, 1000) * HZ + HZ; |
| else |
| timeout = 10 * HZ; |
| schedule_delayed_work(&host->timeout_work, timeout); |
| |
| host->cmd = cmd; |
| |
| /* Clear any error flags */ |
| sdhsts = readl(host->ioaddr + SDHSTS); |
| if (sdhsts & SDHSTS_ERROR_MASK) |
| writel(sdhsts, host->ioaddr + SDHSTS); |
| |
| if ((cmd->flags & MMC_RSP_136) && (cmd->flags & MMC_RSP_BUSY)) { |
| dev_err(dev, "unsupported response type!\n"); |
| cmd->error = -EINVAL; |
| bcm2835_finish_request(host); |
| return false; |
| } |
| |
| bcm2835_prepare_data(host, cmd); |
| |
| writel(cmd->arg, host->ioaddr + SDARG); |
| |
| sdcmd = cmd->opcode & SDCMD_CMD_MASK; |
| |
| host->use_busy = false; |
| if (!(cmd->flags & MMC_RSP_PRESENT)) { |
| sdcmd |= SDCMD_NO_RESPONSE; |
| } else { |
| if (cmd->flags & MMC_RSP_136) |
| sdcmd |= SDCMD_LONG_RESPONSE; |
| if (cmd->flags & MMC_RSP_BUSY) { |
| sdcmd |= SDCMD_BUSYWAIT; |
| host->use_busy = true; |
| } |
| } |
| |
| if (cmd->data) { |
| if (cmd->data->flags & MMC_DATA_WRITE) |
| sdcmd |= SDCMD_WRITE_CMD; |
| if (cmd->data->flags & MMC_DATA_READ) |
| sdcmd |= SDCMD_READ_CMD; |
| } |
| |
| writel(sdcmd | SDCMD_NEW_FLAG, host->ioaddr + SDCMD); |
| |
| return true; |
| } |
| |
| static void bcm2835_transfer_complete(struct bcm2835_host *host) |
| { |
| struct mmc_data *data; |
| |
| WARN_ON(!host->data_complete); |
| |
| data = host->data; |
| host->data = NULL; |
| |
| /* Need to send CMD12 if - |
| * a) open-ended multiblock transfer (no CMD23) |
| * b) error in multiblock transfer |
| */ |
| if (host->mrq->stop && (data->error || !host->use_sbc)) { |
| if (bcm2835_send_command(host, host->mrq->stop)) { |
| /* No busy, so poll for completion */ |
| if (!host->use_busy) |
| bcm2835_finish_command(host); |
| } |
| } else { |
| bcm2835_wait_transfer_complete(host); |
| bcm2835_finish_request(host); |
| } |
| } |
| |
| static void bcm2835_finish_data(struct bcm2835_host *host) |
| { |
| struct device *dev = &host->pdev->dev; |
| struct mmc_data *data; |
| |
| data = host->data; |
| |
| host->hcfg &= ~(SDHCFG_DATA_IRPT_EN | SDHCFG_BLOCK_IRPT_EN); |
| writel(host->hcfg, host->ioaddr + SDHCFG); |
| |
| data->bytes_xfered = data->error ? 0 : (data->blksz * data->blocks); |
| |
| host->data_complete = true; |
| |
| if (host->cmd) { |
| /* Data managed to finish before the |
| * command completed. Make sure we do |
| * things in the proper order. |
| */ |
| dev_dbg(dev, "Finished early - HSTS %08x\n", |
| readl(host->ioaddr + SDHSTS)); |
| } else { |
| bcm2835_transfer_complete(host); |
| } |
| } |
| |
| static void bcm2835_finish_command(struct bcm2835_host *host) |
| { |
| struct device *dev = &host->pdev->dev; |
| struct mmc_command *cmd = host->cmd; |
| u32 sdcmd; |
| |
| sdcmd = bcm2835_read_wait_sdcmd(host, 100); |
| |
| /* Check for errors */ |
| if (sdcmd & SDCMD_NEW_FLAG) { |
| dev_err(dev, "command never completed.\n"); |
| bcm2835_dumpregs(host); |
| host->cmd->error = -EIO; |
| bcm2835_finish_request(host); |
| return; |
| } else if (sdcmd & SDCMD_FAIL_FLAG) { |
| u32 sdhsts = readl(host->ioaddr + SDHSTS); |
| |
| /* Clear the errors */ |
| writel(SDHSTS_ERROR_MASK, host->ioaddr + SDHSTS); |
| |
| if (!(sdhsts & SDHSTS_CRC7_ERROR) || |
| (host->cmd->opcode != MMC_SEND_OP_COND)) { |
| u32 edm, fsm; |
| |
| if (sdhsts & SDHSTS_CMD_TIME_OUT) { |
| host->cmd->error = -ETIMEDOUT; |
| } else { |
| dev_err(dev, "unexpected command %d error\n", |
| host->cmd->opcode); |
| bcm2835_dumpregs(host); |
| host->cmd->error = -EILSEQ; |
| } |
| edm = readl(host->ioaddr + SDEDM); |
| fsm = edm & SDEDM_FSM_MASK; |
| if (fsm == SDEDM_FSM_READWAIT || |
| fsm == SDEDM_FSM_WRITESTART1) |
| /* Kick the FSM out of its wait */ |
| writel(edm | SDEDM_FORCE_DATA_MODE, |
| host->ioaddr + SDEDM); |
| bcm2835_finish_request(host); |
| return; |
| } |
| } |
| |
| if (cmd->flags & MMC_RSP_PRESENT) { |
| if (cmd->flags & MMC_RSP_136) { |
| int i; |
| |
| for (i = 0; i < 4; i++) { |
| cmd->resp[3 - i] = |
| readl(host->ioaddr + SDRSP0 + i * 4); |
| } |
| } else { |
| cmd->resp[0] = readl(host->ioaddr + SDRSP0); |
| } |
| } |
| |
| if (cmd == host->mrq->sbc) { |
| /* Finished CMD23, now send actual command. */ |
| host->cmd = NULL; |
| if (bcm2835_send_command(host, host->mrq->cmd)) { |
| if (host->data && host->dma_desc) |
| /* DMA transfer starts now, PIO starts |
| * after irq |
| */ |
| bcm2835_start_dma(host); |
| |
| if (!host->use_busy) |
| bcm2835_finish_command(host); |
| } |
| } else if (cmd == host->mrq->stop) { |
| /* Finished CMD12 */ |
| bcm2835_finish_request(host); |
| } else { |
| /* Processed actual command. */ |
| host->cmd = NULL; |
| if (!host->data) |
| bcm2835_finish_request(host); |
| else if (host->data_complete) |
| bcm2835_transfer_complete(host); |
| } |
| } |
| |
| static void bcm2835_timeout(struct work_struct *work) |
| { |
| struct delayed_work *d = to_delayed_work(work); |
| struct bcm2835_host *host = |
| container_of(d, struct bcm2835_host, timeout_work); |
| struct device *dev = &host->pdev->dev; |
| |
| mutex_lock(&host->mutex); |
| |
| if (host->mrq) { |
| dev_err(dev, "timeout waiting for hardware interrupt.\n"); |
| bcm2835_dumpregs(host); |
| |
| bcm2835_reset(host->mmc); |
| |
| if (host->data) { |
| host->data->error = -ETIMEDOUT; |
| bcm2835_finish_data(host); |
| } else { |
| if (host->cmd) |
| host->cmd->error = -ETIMEDOUT; |
| else |
| host->mrq->cmd->error = -ETIMEDOUT; |
| |
| bcm2835_finish_request(host); |
| } |
| } |
| |
| mutex_unlock(&host->mutex); |
| } |
| |
| static bool bcm2835_check_cmd_error(struct bcm2835_host *host, u32 intmask) |
| { |
| struct device *dev = &host->pdev->dev; |
| |
| if (!(intmask & SDHSTS_ERROR_MASK)) |
| return false; |
| |
| if (!host->cmd) |
| return true; |
| |
| dev_err(dev, "sdhost_busy_irq: intmask %08x\n", intmask); |
| if (intmask & SDHSTS_CRC7_ERROR) { |
| host->cmd->error = -EILSEQ; |
| } else if (intmask & (SDHSTS_CRC16_ERROR | |
| SDHSTS_FIFO_ERROR)) { |
| if (host->mrq->data) |
| host->mrq->data->error = -EILSEQ; |
| else |
| host->cmd->error = -EILSEQ; |
| } else if (intmask & SDHSTS_REW_TIME_OUT) { |
| if (host->mrq->data) |
| host->mrq->data->error = -ETIMEDOUT; |
| else |
| host->cmd->error = -ETIMEDOUT; |
| } else if (intmask & SDHSTS_CMD_TIME_OUT) { |
| host->cmd->error = -ETIMEDOUT; |
| } |
| bcm2835_dumpregs(host); |
| return true; |
| } |
| |
| static void bcm2835_check_data_error(struct bcm2835_host *host, u32 intmask) |
| { |
| if (!host->data) |
| return; |
| if (intmask & (SDHSTS_CRC16_ERROR | SDHSTS_FIFO_ERROR)) |
| host->data->error = -EILSEQ; |
| if (intmask & SDHSTS_REW_TIME_OUT) |
| host->data->error = -ETIMEDOUT; |
| } |
| |
| static void bcm2835_busy_irq(struct bcm2835_host *host) |
| { |
| if (WARN_ON(!host->cmd)) { |
| bcm2835_dumpregs(host); |
| return; |
| } |
| |
| if (WARN_ON(!host->use_busy)) { |
| bcm2835_dumpregs(host); |
| return; |
| } |
| host->use_busy = false; |
| |
| bcm2835_finish_command(host); |
| } |
| |
| static void bcm2835_data_irq(struct bcm2835_host *host, u32 intmask) |
| { |
| /* There are no dedicated data/space available interrupt |
| * status bits, so it is necessary to use the single shared |
| * data/space available FIFO status bits. It is therefore not |
| * an error to get here when there is no data transfer in |
| * progress. |
| */ |
| if (!host->data) |
| return; |
| |
| bcm2835_check_data_error(host, intmask); |
| if (host->data->error) |
| goto finished; |
| |
| if (host->data->flags & MMC_DATA_WRITE) { |
| /* Use the block interrupt for writes after the first block */ |
| host->hcfg &= ~(SDHCFG_DATA_IRPT_EN); |
| host->hcfg |= SDHCFG_BLOCK_IRPT_EN; |
| writel(host->hcfg, host->ioaddr + SDHCFG); |
| bcm2835_transfer_pio(host); |
| } else { |
| bcm2835_transfer_pio(host); |
| host->blocks--; |
| if ((host->blocks == 0) || host->data->error) |
| goto finished; |
| } |
| return; |
| |
| finished: |
| host->hcfg &= ~(SDHCFG_DATA_IRPT_EN | SDHCFG_BLOCK_IRPT_EN); |
| writel(host->hcfg, host->ioaddr + SDHCFG); |
| } |
| |
| static void bcm2835_data_threaded_irq(struct bcm2835_host *host) |
| { |
| if (!host->data) |
| return; |
| if ((host->blocks == 0) || host->data->error) |
| bcm2835_finish_data(host); |
| } |
| |
| static void bcm2835_block_irq(struct bcm2835_host *host) |
| { |
| if (WARN_ON(!host->data)) { |
| bcm2835_dumpregs(host); |
| return; |
| } |
| |
| if (!host->dma_desc) { |
| WARN_ON(!host->blocks); |
| if (host->data->error || (--host->blocks == 0)) |
| bcm2835_finish_data(host); |
| else |
| bcm2835_transfer_pio(host); |
| } else if (host->data->flags & MMC_DATA_WRITE) { |
| bcm2835_finish_data(host); |
| } |
| } |
| |
| static irqreturn_t bcm2835_irq(int irq, void *dev_id) |
| { |
| irqreturn_t result = IRQ_NONE; |
| struct bcm2835_host *host = dev_id; |
| u32 intmask; |
| |
| spin_lock(&host->lock); |
| |
| intmask = readl(host->ioaddr + SDHSTS); |
| |
| writel(SDHSTS_BUSY_IRPT | |
| SDHSTS_BLOCK_IRPT | |
| SDHSTS_SDIO_IRPT | |
| SDHSTS_DATA_FLAG, |
| host->ioaddr + SDHSTS); |
| |
| if (intmask & SDHSTS_BLOCK_IRPT) { |
| bcm2835_check_data_error(host, intmask); |
| host->irq_block = true; |
| result = IRQ_WAKE_THREAD; |
| } |
| |
| if (intmask & SDHSTS_BUSY_IRPT) { |
| if (!bcm2835_check_cmd_error(host, intmask)) { |
| host->irq_busy = true; |
| result = IRQ_WAKE_THREAD; |
| } else { |
| result = IRQ_HANDLED; |
| } |
| } |
| |
| /* There is no true data interrupt status bit, so it is |
| * necessary to qualify the data flag with the interrupt |
| * enable bit. |
| */ |
| if ((intmask & SDHSTS_DATA_FLAG) && |
| (host->hcfg & SDHCFG_DATA_IRPT_EN)) { |
| bcm2835_data_irq(host, intmask); |
| host->irq_data = true; |
| result = IRQ_WAKE_THREAD; |
| } |
| |
| spin_unlock(&host->lock); |
| |
| return result; |
| } |
| |
| static irqreturn_t bcm2835_threaded_irq(int irq, void *dev_id) |
| { |
| struct bcm2835_host *host = dev_id; |
| unsigned long flags; |
| bool block, busy, data; |
| |
| spin_lock_irqsave(&host->lock, flags); |
| |
| block = host->irq_block; |
| busy = host->irq_busy; |
| data = host->irq_data; |
| host->irq_block = false; |
| host->irq_busy = false; |
| host->irq_data = false; |
| |
| spin_unlock_irqrestore(&host->lock, flags); |
| |
| mutex_lock(&host->mutex); |
| |
| if (block) |
| bcm2835_block_irq(host); |
| if (busy) |
| bcm2835_busy_irq(host); |
| if (data) |
| bcm2835_data_threaded_irq(host); |
| |
| mutex_unlock(&host->mutex); |
| |
| return IRQ_HANDLED; |
| } |
| |
| static void bcm2835_dma_complete_work(struct work_struct *work) |
| { |
| struct bcm2835_host *host = |
| container_of(work, struct bcm2835_host, dma_work); |
| struct mmc_data *data = host->data; |
| |
| mutex_lock(&host->mutex); |
| |
| if (host->dma_chan) { |
| dma_unmap_sg(host->dma_chan->device->dev, |
| data->sg, data->sg_len, |
| host->dma_dir); |
| |
| host->dma_chan = NULL; |
| } |
| |
| if (host->drain_words) { |
| unsigned long flags; |
| void *page; |
| u32 *buf; |
| |
| if (host->drain_offset & PAGE_MASK) { |
| host->drain_page += host->drain_offset >> PAGE_SHIFT; |
| host->drain_offset &= ~PAGE_MASK; |
| } |
| local_irq_save(flags); |
| page = kmap_atomic(host->drain_page); |
| buf = page + host->drain_offset; |
| |
| while (host->drain_words) { |
| u32 edm = readl(host->ioaddr + SDEDM); |
| |
| if ((edm >> 4) & 0x1f) |
| *(buf++) = readl(host->ioaddr + SDDATA); |
| host->drain_words--; |
| } |
| |
| kunmap_atomic(page); |
| local_irq_restore(flags); |
| } |
| |
| bcm2835_finish_data(host); |
| |
| mutex_unlock(&host->mutex); |
| } |
| |
| static void bcm2835_set_clock(struct bcm2835_host *host, unsigned int clock) |
| { |
| int div; |
| |
| /* The SDCDIV register has 11 bits, and holds (div - 2). But |
| * in data mode the max is 50MHz wihout a minimum, and only |
| * the bottom 3 bits are used. Since the switch over is |
| * automatic (unless we have marked the card as slow...), |
| * chosen values have to make sense in both modes. Ident mode |
| * must be 100-400KHz, so can range check the requested |
| * clock. CMD15 must be used to return to data mode, so this |
| * can be monitored. |
| * |
| * clock 250MHz -> 0->125MHz, 1->83.3MHz, 2->62.5MHz, 3->50.0MHz |
| * 4->41.7MHz, 5->35.7MHz, 6->31.3MHz, 7->27.8MHz |
| * |
| * 623->400KHz/27.8MHz |
| * reset value (507)->491159/50MHz |
| * |
| * BUT, the 3-bit clock divisor in data mode is too small if |
| * the core clock is higher than 250MHz, so instead use the |
| * SLOW_CARD configuration bit to force the use of the ident |
| * clock divisor at all times. |
| */ |
| |
| if (clock < 100000) { |
| /* Can't stop the clock, but make it as slow as possible |
| * to show willing |
| */ |
| host->cdiv = SDCDIV_MAX_CDIV; |
| writel(host->cdiv, host->ioaddr + SDCDIV); |
| return; |
| } |
| |
| div = host->max_clk / clock; |
| if (div < 2) |
| div = 2; |
| if ((host->max_clk / div) > clock) |
| div++; |
| div -= 2; |
| |
| if (div > SDCDIV_MAX_CDIV) |
| div = SDCDIV_MAX_CDIV; |
| |
| clock = host->max_clk / (div + 2); |
| host->mmc->actual_clock = clock; |
| |
| /* Calibrate some delays */ |
| |
| host->ns_per_fifo_word = (1000000000 / clock) * |
| ((host->mmc->caps & MMC_CAP_4_BIT_DATA) ? 8 : 32); |
| |
| host->cdiv = div; |
| writel(host->cdiv, host->ioaddr + SDCDIV); |
| |
| /* Set the timeout to 500ms */ |
| writel(host->mmc->actual_clock / 2, host->ioaddr + SDTOUT); |
| } |
| |
| static void bcm2835_request(struct mmc_host *mmc, struct mmc_request *mrq) |
| { |
| struct bcm2835_host *host = mmc_priv(mmc); |
| struct device *dev = &host->pdev->dev; |
| u32 edm, fsm; |
| |
| /* Reset the error statuses in case this is a retry */ |
| if (mrq->sbc) |
| mrq->sbc->error = 0; |
| if (mrq->cmd) |
| mrq->cmd->error = 0; |
| if (mrq->data) |
| mrq->data->error = 0; |
| if (mrq->stop) |
| mrq->stop->error = 0; |
| |
| if (mrq->data && !is_power_of_2(mrq->data->blksz)) { |
| dev_err(dev, "unsupported block size (%d bytes)\n", |
| mrq->data->blksz); |
| |
| if (mrq->cmd) |
| mrq->cmd->error = -EINVAL; |
| |
| mmc_request_done(mmc, mrq); |
| return; |
| } |
| |
| if (host->use_dma && mrq->data && (mrq->data->blocks > PIO_THRESHOLD)) |
| bcm2835_prepare_dma(host, mrq->data); |
| |
| mutex_lock(&host->mutex); |
| |
| WARN_ON(host->mrq); |
| host->mrq = mrq; |
| |
| edm = readl(host->ioaddr + SDEDM); |
| fsm = edm & SDEDM_FSM_MASK; |
| |
| if ((fsm != SDEDM_FSM_IDENTMODE) && |
| (fsm != SDEDM_FSM_DATAMODE)) { |
| dev_err(dev, "previous command (%d) not complete (EDM %08x)\n", |
| readl(host->ioaddr + SDCMD) & SDCMD_CMD_MASK, |
| edm); |
| bcm2835_dumpregs(host); |
| |
| if (mrq->cmd) |
| mrq->cmd->error = -EILSEQ; |
| |
| bcm2835_finish_request(host); |
| mutex_unlock(&host->mutex); |
| return; |
| } |
| |
| host->use_sbc = !!mrq->sbc && host->mrq->data && |
| (host->mrq->data->flags & MMC_DATA_READ); |
| if (host->use_sbc) { |
| if (bcm2835_send_command(host, mrq->sbc)) { |
| if (!host->use_busy) |
| bcm2835_finish_command(host); |
| } |
| } else if (mrq->cmd && bcm2835_send_command(host, mrq->cmd)) { |
| if (host->data && host->dma_desc) { |
| /* DMA transfer starts now, PIO starts after irq */ |
| bcm2835_start_dma(host); |
| } |
| |
| if (!host->use_busy) |
| bcm2835_finish_command(host); |
| } |
| |
| mutex_unlock(&host->mutex); |
| } |
| |
| static void bcm2835_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) |
| { |
| struct bcm2835_host *host = mmc_priv(mmc); |
| |
| mutex_lock(&host->mutex); |
| |
| if (!ios->clock || ios->clock != host->clock) { |
| bcm2835_set_clock(host, ios->clock); |
| host->clock = ios->clock; |
| } |
| |
| /* set bus width */ |
| host->hcfg &= ~SDHCFG_WIDE_EXT_BUS; |
| if (ios->bus_width == MMC_BUS_WIDTH_4) |
| host->hcfg |= SDHCFG_WIDE_EXT_BUS; |
| |
| host->hcfg |= SDHCFG_WIDE_INT_BUS; |
| |
| /* Disable clever clock switching, to cope with fast core clocks */ |
| host->hcfg |= SDHCFG_SLOW_CARD; |
| |
| writel(host->hcfg, host->ioaddr + SDHCFG); |
| |
| mutex_unlock(&host->mutex); |
| } |
| |
| static const struct mmc_host_ops bcm2835_ops = { |
| .request = bcm2835_request, |
| .set_ios = bcm2835_set_ios, |
| .hw_reset = bcm2835_reset, |
| }; |
| |
| static int bcm2835_add_host(struct bcm2835_host *host) |
| { |
| struct mmc_host *mmc = host->mmc; |
| struct device *dev = &host->pdev->dev; |
| char pio_limit_string[20]; |
| int ret; |
| |
| if (!mmc->f_max || mmc->f_max > host->max_clk) |
| mmc->f_max = host->max_clk; |
| mmc->f_min = host->max_clk / SDCDIV_MAX_CDIV; |
| |
| mmc->max_busy_timeout = ~0 / (mmc->f_max / 1000); |
| |
| dev_dbg(dev, "f_max %d, f_min %d, max_busy_timeout %d\n", |
| mmc->f_max, mmc->f_min, mmc->max_busy_timeout); |
| |
| /* host controller capabilities */ |
| mmc->caps |= MMC_CAP_SD_HIGHSPEED | MMC_CAP_MMC_HIGHSPEED | |
| MMC_CAP_NEEDS_POLL | MMC_CAP_HW_RESET | MMC_CAP_ERASE | |
| MMC_CAP_CMD23; |
| |
| spin_lock_init(&host->lock); |
| mutex_init(&host->mutex); |
| |
| if (IS_ERR_OR_NULL(host->dma_chan_rxtx)) { |
| dev_warn(dev, "unable to initialise DMA channel. Falling back to PIO\n"); |
| host->use_dma = false; |
| } else { |
| host->use_dma = true; |
| |
| host->dma_cfg_tx.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES; |
| host->dma_cfg_tx.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES; |
| host->dma_cfg_tx.slave_id = 13; /* DREQ channel */ |
| host->dma_cfg_tx.direction = DMA_MEM_TO_DEV; |
| host->dma_cfg_tx.src_addr = 0; |
| host->dma_cfg_tx.dst_addr = host->phys_addr + SDDATA; |
| |
| host->dma_cfg_rx.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES; |
| host->dma_cfg_rx.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES; |
| host->dma_cfg_rx.slave_id = 13; /* DREQ channel */ |
| host->dma_cfg_rx.direction = DMA_DEV_TO_MEM; |
| host->dma_cfg_rx.src_addr = host->phys_addr + SDDATA; |
| host->dma_cfg_rx.dst_addr = 0; |
| |
| if (dmaengine_slave_config(host->dma_chan_rxtx, |
| &host->dma_cfg_tx) != 0 || |
| dmaengine_slave_config(host->dma_chan_rxtx, |
| &host->dma_cfg_rx) != 0) |
| host->use_dma = false; |
| } |
| |
| mmc->max_segs = 128; |
| mmc->max_req_size = 524288; |
| mmc->max_seg_size = mmc->max_req_size; |
| mmc->max_blk_size = 1024; |
| mmc->max_blk_count = 65535; |
| |
| /* report supported voltage ranges */ |
| mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34; |
| |
| INIT_WORK(&host->dma_work, bcm2835_dma_complete_work); |
| INIT_DELAYED_WORK(&host->timeout_work, bcm2835_timeout); |
| |
| /* Set interrupt enables */ |
| host->hcfg = SDHCFG_BUSY_IRPT_EN; |
| |
| bcm2835_reset_internal(host); |
| |
| ret = request_threaded_irq(host->irq, bcm2835_irq, |
| bcm2835_threaded_irq, |
| 0, mmc_hostname(mmc), host); |
| if (ret) { |
| dev_err(dev, "failed to request IRQ %d: %d\n", host->irq, ret); |
| return ret; |
| } |
| |
| ret = mmc_add_host(mmc); |
| if (ret) { |
| free_irq(host->irq, host); |
| return ret; |
| } |
| |
| pio_limit_string[0] = '\0'; |
| if (host->use_dma && (PIO_THRESHOLD > 0)) |
| sprintf(pio_limit_string, " (>%d)", PIO_THRESHOLD); |
| dev_info(dev, "loaded - DMA %s%s\n", |
| host->use_dma ? "enabled" : "disabled", pio_limit_string); |
| |
| return 0; |
| } |
| |
| static int bcm2835_probe(struct platform_device *pdev) |
| { |
| struct device *dev = &pdev->dev; |
| struct clk *clk; |
| struct resource *iomem; |
| struct bcm2835_host *host; |
| struct mmc_host *mmc; |
| const __be32 *regaddr_p; |
| int ret; |
| |
| dev_dbg(dev, "%s\n", __func__); |
| mmc = mmc_alloc_host(sizeof(*host), dev); |
| if (!mmc) |
| return -ENOMEM; |
| |
| mmc->ops = &bcm2835_ops; |
| host = mmc_priv(mmc); |
| host->mmc = mmc; |
| host->pdev = pdev; |
| spin_lock_init(&host->lock); |
| |
| iomem = platform_get_resource(pdev, IORESOURCE_MEM, 0); |
| host->ioaddr = devm_ioremap_resource(dev, iomem); |
| if (IS_ERR(host->ioaddr)) { |
| ret = PTR_ERR(host->ioaddr); |
| goto err; |
| } |
| |
| /* Parse OF address directly to get the physical address for |
| * DMA to our registers. |
| */ |
| regaddr_p = of_get_address(pdev->dev.of_node, 0, NULL, NULL); |
| if (!regaddr_p) { |
| dev_err(dev, "Can't get phys address\n"); |
| ret = -EINVAL; |
| goto err; |
| } |
| |
| host->phys_addr = be32_to_cpup(regaddr_p); |
| |
| host->dma_chan = NULL; |
| host->dma_desc = NULL; |
| |
| host->dma_chan_rxtx = dma_request_slave_channel(dev, "rx-tx"); |
| |
| clk = devm_clk_get(dev, NULL); |
| if (IS_ERR(clk)) { |
| ret = PTR_ERR(clk); |
| if (ret != -EPROBE_DEFER) |
| dev_err(dev, "could not get clk: %d\n", ret); |
| goto err; |
| } |
| |
| host->max_clk = clk_get_rate(clk); |
| |
| host->irq = platform_get_irq(pdev, 0); |
| if (host->irq <= 0) { |
| dev_err(dev, "get IRQ failed\n"); |
| ret = -EINVAL; |
| goto err; |
| } |
| |
| ret = mmc_of_parse(mmc); |
| if (ret) |
| goto err; |
| |
| ret = bcm2835_add_host(host); |
| if (ret) |
| goto err; |
| |
| platform_set_drvdata(pdev, host); |
| |
| dev_dbg(dev, "%s -> OK\n", __func__); |
| |
| return 0; |
| |
| err: |
| dev_dbg(dev, "%s -> err %d\n", __func__, ret); |
| if (host->dma_chan_rxtx) |
| dma_release_channel(host->dma_chan_rxtx); |
| mmc_free_host(mmc); |
| |
| return ret; |
| } |
| |
| static int bcm2835_remove(struct platform_device *pdev) |
| { |
| struct bcm2835_host *host = platform_get_drvdata(pdev); |
| |
| mmc_remove_host(host->mmc); |
| |
| writel(SDVDD_POWER_OFF, host->ioaddr + SDVDD); |
| |
| free_irq(host->irq, host); |
| |
| cancel_work_sync(&host->dma_work); |
| cancel_delayed_work_sync(&host->timeout_work); |
| |
| mmc_free_host(host->mmc); |
| platform_set_drvdata(pdev, NULL); |
| |
| return 0; |
| } |
| |
| static const struct of_device_id bcm2835_match[] = { |
| { .compatible = "brcm,bcm2835-sdhost" }, |
| { } |
| }; |
| MODULE_DEVICE_TABLE(of, bcm2835_match); |
| |
| static struct platform_driver bcm2835_driver = { |
| .probe = bcm2835_probe, |
| .remove = bcm2835_remove, |
| .driver = { |
| .name = "sdhost-bcm2835", |
| .of_match_table = bcm2835_match, |
| }, |
| }; |
| module_platform_driver(bcm2835_driver); |
| |
| MODULE_ALIAS("platform:sdhost-bcm2835"); |
| MODULE_DESCRIPTION("BCM2835 SDHost driver"); |
| MODULE_LICENSE("GPL v2"); |
| MODULE_AUTHOR("Phil Elwell"); |