drivers/misc/Kconfig - LeafOS-Devices/android_kernel_samsung_gta4xl - Gitiles

 #
 # Misc strange devices
 #

 menu "Misc devices"

 config SENSORS_LIS3LV02D
 	tristate
 	depends on INPUT
 	select INPUT_POLLDEV
 	default n

 config AD525X_DPOT
 	tristate "Analog Devices Digital Potentiometers"
 	depends on (I2C || SPI) && SYSFS
 	help
 	  If you say yes here, you get support for the Analog Devices
 	  AD5258, AD5259, AD5251, AD5252, AD5253, AD5254, AD5255
 	  AD5160, AD5161, AD5162, AD5165, AD5200, AD5201, AD5203,
 	  AD5204, AD5206, AD5207, AD5231, AD5232, AD5233, AD5235,
 	  AD5260, AD5262, AD5263, AD5290, AD5291, AD5292, AD5293,
 	  AD7376, AD8400, AD8402, AD8403, ADN2850, AD5241, AD5242,
 	  AD5243, AD5245, AD5246, AD5247, AD5248, AD5280, AD5282,
 	  ADN2860, AD5273, AD5171, AD5170, AD5172, AD5173, AD5270,
 	  AD5271, AD5272, AD5274
 	  digital potentiometer chips.

 	  See Documentation/misc-devices/ad525x_dpot.txt for the
 	  userspace interface.

 	  This driver can also be built as a module.  If so, the module
 	  will be called ad525x_dpot.

 config AD525X_DPOT_I2C
 	tristate "support I2C bus connection"
 	depends on AD525X_DPOT && I2C
 	help
 	  Say Y here if you have a digital potentiometers hooked to an I2C bus.

 	  To compile this driver as a module, choose M here: the
 	  module will be called ad525x_dpot-i2c.

 config AD525X_DPOT_SPI
 	tristate "support SPI bus connection"
 	depends on AD525X_DPOT && SPI_MASTER
 	help
 	  Say Y here if you have a digital potentiometers hooked to an SPI bus.

 	  If unsure, say N (but it's safe to say "Y").

 	  To compile this driver as a module, choose M here: the
 	  module will be called ad525x_dpot-spi.

 config ATMEL_TCLIB
 	bool "Atmel AT32/AT91 Timer/Counter Library"
 	depends on (AVR32 || ARCH_AT91)
 	help
 	  Select this if you want a library to allocate the Timer/Counter
 	  blocks found on many Atmel processors.  This facilitates using
 	  these blocks by different drivers despite processor differences.

 config ATMEL_TCB_CLKSRC
 	bool "TC Block Clocksource"
 	depends on ATMEL_TCLIB
 	default y
 	help
 	  Select this to get a high precision clocksource based on a
 	  TC block with a 5+ MHz base clock rate.  Two timer channels
 	  are combined to make a single 32-bit timer.

 	  When GENERIC_CLOCKEVENTS is defined, the third timer channel
 	  may be used as a clock event device supporting oneshot mode
 	  (delays of up to two seconds) based on the 32 KiHz clock.

 config ATMEL_TCB_CLKSRC_BLOCK
 	int
 	depends on ATMEL_TCB_CLKSRC
 	prompt "TC Block" if CPU_AT32AP700X
 	default 0
 	range 0 1
 	help
 	  Some chips provide more than one TC block, so you have the
 	  choice of which one to use for the clock framework.  The other
 	  TC can be used for other purposes, such as PWM generation and
 	  interval timing.

 config DUMMY_IRQ
 	tristate "Dummy IRQ handler"
 	default n
 	---help---
 	  This module accepts a single 'irq' parameter, which it should register for.
 	  The sole purpose of this module is to help with debugging of systems on
 	  which spurious IRQs would happen on disabled IRQ vector.

 config IBM_ASM
 	tristate "Device driver for IBM RSA service processor"
 	depends on X86 && PCI && INPUT
 	depends on SERIAL_8250 || SERIAL_8250=n
 	---help---
 	  This option enables device driver support for in-band access to the
 	  IBM RSA (Condor) service processor in eServer xSeries systems.
 	  The ibmasm device driver allows user space application to access
 	  ASM (Advanced Systems Management) functions on the service
 	  processor. The driver is meant to be used in conjunction with
 	  a user space API.
 	  The ibmasm driver also enables the OS to use the UART on the
 	  service processor board as a regular serial port. To make use of
 	  this feature serial driver support (CONFIG_SERIAL_8250) must be
 	  enabled.

 	  WARNING: This software may not be supported or function
 	  correctly on your IBM server. Please consult the IBM ServerProven
 	  website <http://www-03.ibm.com/systems/info/x86servers/serverproven/compat/us/>
 	  for information on the specific driver level and support statement
 	  for your IBM server.

 config PHANTOM
 	tristate "Sensable PHANToM (PCI)"
 	depends on PCI
 	help
 	  Say Y here if you want to build a driver for Sensable PHANToM device.

 	  This driver is only for PCI PHANToMs.

 	  If you choose to build module, its name will be phantom. If unsure,
 	  say N here.

 config INTEL_MID_PTI
 	tristate "Parallel Trace Interface for MIPI P1149.7 cJTAG standard"
 	depends on PCI && TTY && (X86_INTEL_MID || COMPILE_TEST)
 	default n
 	help
 	  The PTI (Parallel Trace Interface) driver directs
 	  trace data routed from various parts in the system out
 	  through an Intel Penwell PTI port and out of the mobile
 	  device for analysis with a debugging tool (Lauterbach or Fido).

 	  You should select this driver if the target kernel is meant for
 	  an Intel Atom (non-netbook) mobile device containing a MIPI
 	  P1149.7 standard implementation.

 config SGI_IOC4
 	tristate "SGI IOC4 Base IO support"
 	depends on PCI
 	---help---
 	  This option enables basic support for the IOC4 chip on certain
 	  SGI IO controller cards (IO9, IO10, and PCI-RT).  This option
 	  does not enable any specific functions on such a card, but provides
 	  necessary infrastructure for other drivers to utilize.

 	  If you have an SGI Altix with an IOC4-based card say Y.
 	  Otherwise say N.

 config TIFM_CORE
 	tristate "TI Flash Media interface support"
 	depends on PCI
 	help
 	  If you want support for Texas Instruments(R) Flash Media adapters
 	  you should select this option and then also choose an appropriate
 	  host adapter, such as 'TI Flash Media PCI74xx/PCI76xx host adapter
 	  support', if you have a TI PCI74xx compatible card reader, for
 	  example.
 	  You will also have to select some flash card format drivers. MMC/SD
 	  cards are supported via 'MMC/SD Card support: TI Flash Media MMC/SD
 	  Interface support (MMC_TIFM_SD)'.

 	  To compile this driver as a module, choose M here: the module will
 	  be called tifm_core.

 config TIFM_7XX1
 	tristate "TI Flash Media PCI74xx/PCI76xx host adapter support"
 	depends on PCI && TIFM_CORE
 	default TIFM_CORE
 	help
 	  This option enables support for Texas Instruments(R) PCI74xx and
 	  PCI76xx families of Flash Media adapters, found in many laptops.
 	  To make actual use of the device, you will have to select some
 	  flash card format drivers, as outlined in the TIFM_CORE Help.

 	  To compile this driver as a module, choose M here: the module will
 	  be called tifm_7xx1.

 config ICS932S401
 	tristate "Integrated Circuits ICS932S401"
 	depends on I2C
 	help
 	  If you say yes here you get support for the Integrated Circuits
 	  ICS932S401 clock control chips.

 	  This driver can also be built as a module. If so, the module
 	  will be called ics932s401.

 config ATMEL_SSC
 	tristate "Device driver for Atmel SSC peripheral"
 	depends on HAS_IOMEM && (AVR32 || ARCH_AT91 || COMPILE_TEST)
 	---help---
 	  This option enables device driver support for Atmel Synchronized
 	  Serial Communication peripheral (SSC).

 	  The SSC peripheral supports a wide variety of serial frame based
 	  communications, i.e. I2S, SPI, etc.

 	  If unsure, say N.

 config ENCLOSURE_SERVICES
 	tristate "Enclosure Services"
 	default n
 	help
 	  Provides support for intelligent enclosures (bays which
 	  contain storage devices).  You also need either a host
 	  driver (SCSI/ATA) which supports enclosures
 	  or a SCSI enclosure device (SES) to use these services.

 config SGI_XP
 	tristate "Support communication between SGI SSIs"
 	depends on NET
 	depends on (IA64_GENERIC || IA64_SGI_SN2 || IA64_SGI_UV || X86_UV) && SMP
 	select IA64_UNCACHED_ALLOCATOR if IA64_GENERIC || IA64_SGI_SN2
 	select GENERIC_ALLOCATOR if IA64_GENERIC || IA64_SGI_SN2
 	select SGI_GRU if X86_64 && SMP
 	---help---
 	  An SGI machine can be divided into multiple Single System
 	  Images which act independently of each other and have
 	  hardware based memory protection from the others.  Enabling
 	  this feature will allow for direct communication between SSIs
 	  based on a network adapter and DMA messaging.

 config CS5535_MFGPT
 	tristate "CS5535/CS5536 Geode Multi-Function General Purpose Timer (MFGPT) support"
 	depends on MFD_CS5535
 	default n
 	help
 	  This driver provides access to MFGPT functionality for other
 	  drivers that need timers.  MFGPTs are available in the CS5535 and
 	  CS5536 companion chips that are found in AMD Geode and several
 	  other platforms.  They have a better resolution and max interval
 	  than the generic PIT, and are suitable for use as high-res timers.
 	  You probably don't want to enable this manually; other drivers that
 	  make use of it should enable it.

 config CS5535_MFGPT_DEFAULT_IRQ
 	int
 	depends on CS5535_MFGPT
 	default 7
 	help
 	  MFGPTs on the CS5535 require an interrupt.  The selected IRQ
 	  can be overridden as a module option as well as by driver that
 	  use the cs5535_mfgpt_ API; however, different architectures might
 	  want to use a different IRQ by default.  This is here for
 	  architectures to set as necessary.

 config CS5535_CLOCK_EVENT_SRC
 	tristate "CS5535/CS5536 high-res timer (MFGPT) events"
 	depends on GENERIC_CLOCKEVENTS && CS5535_MFGPT
 	help
 	  This driver provides a clock event source based on the MFGPT
 	  timer(s) in the CS5535 and CS5536 companion chips.
 	  MFGPTs have a better resolution and max interval than the
 	  generic PIT, and are suitable for use as high-res timers.

 config HP_ILO
 	tristate "Channel interface driver for the HP iLO processor"
 	depends on PCI
 	default n
 	help
 	  The channel interface driver allows applications to communicate
 	  with iLO management processors present on HP ProLiant servers.
 	  Upon loading, the driver creates /dev/hpilo/dXccbN files, which
 	  can be used to gather data from the management processor, via
 	  read and write system calls.

 	  To compile this driver as a module, choose M here: the
 	  module will be called hpilo.

 config QCOM_COINCELL
 	tristate "Qualcomm coincell charger support"
 	depends on MFD_SPMI_PMIC || COMPILE_TEST
 	help
 	  This driver supports the coincell block found inside of
 	  Qualcomm PMICs.  The coincell charger provides a means to
 	  charge a coincell battery or backup capacitor which is used
 	  to maintain PMIC register and RTC state in the absence of
 	  external power.

 config RT_REGMAP
 	tristate "RT Regmap Module"
 	default n
 	help
 	  Say Y here to enable RT regmap support.

 config SGI_GRU
 	tristate "SGI GRU driver"
 	depends on X86_UV && SMP
 	default n
 	select MMU_NOTIFIER
 	---help---
 	The GRU is a hardware resource located in the system chipset. The GRU
 	contains memory that can be mmapped into the user address space. This memory is
 	used to communicate with the GRU to perform functions such as load/store,
 	scatter/gather, bcopy, AMOs, etc.  The GRU is directly accessed by user
 	instructions using user virtual addresses. GRU instructions (ex., bcopy) use
 	user virtual addresses for operands.

 	If you are not running on a SGI UV system, say N.

 config SGI_GRU_DEBUG
 	bool  "SGI GRU driver debug"
 	depends on SGI_GRU
 	default n
 	---help---
 	This option enables additional debugging code for the SGI GRU driver.
 	If you are unsure, say N.

 config APDS9802ALS
 	tristate "Medfield Avago APDS9802 ALS Sensor module"
 	depends on I2C
 	help
 	  If you say yes here you get support for the ALS APDS9802 ambient
 	  light sensor.

 	  This driver can also be built as a module.  If so, the module
 	  will be called apds9802als.

 config ISL29003
 	tristate "Intersil ISL29003 ambient light sensor"
 	depends on I2C && SYSFS
 	help
 	  If you say yes here you get support for the Intersil ISL29003
 	  ambient light sensor.

 	  This driver can also be built as a module.  If so, the module
 	  will be called isl29003.

 config ISL29020
 	tristate "Intersil ISL29020 ambient light sensor"
 	depends on I2C
 	help
 	  If you say yes here you get support for the Intersil ISL29020
 	  ambient light sensor.

 	  This driver can also be built as a module.  If so, the module
 	  will be called isl29020.

 config SENSORS_TSL2550
 	tristate "Taos TSL2550 ambient light sensor"
 	depends on I2C && SYSFS
 	help
 	  If you say yes here you get support for the Taos TSL2550
 	  ambient light sensor.

 	  This driver can also be built as a module.  If so, the module
 	  will be called tsl2550.

 config SENSORS_BH1770
          tristate "BH1770GLC / SFH7770 combined ALS - Proximity sensor"
          depends on I2C
          ---help---
            Say Y here if you want to build a driver for BH1770GLC (ROHM) or
 	   SFH7770 (Osram) combined ambient light and proximity sensor chip.

            To compile this driver as a module, choose M here: the
            module will be called bh1770glc. If unsure, say N here.

 config SENSORS_APDS990X
 	 tristate "APDS990X combined als and proximity sensors"
 	 depends on I2C
 	 default n
 	 ---help---
 	   Say Y here if you want to build a driver for Avago APDS990x
 	   combined ambient light and proximity sensor chip.

 	   To compile this driver as a module, choose M here: the
 	   module will be called apds990x. If unsure, say N here.

 config HMC6352
 	tristate "Honeywell HMC6352 compass"
 	depends on I2C
 	help
 	  This driver provides support for the Honeywell HMC6352 compass,
 	  providing configuration and heading data via sysfs.

 config DS1682
 	tristate "Dallas DS1682 Total Elapsed Time Recorder with Alarm"
 	depends on I2C
 	help
 	  If you say yes here you get support for Dallas Semiconductor
 	  DS1682 Total Elapsed Time Recorder.

 	  This driver can also be built as a module.  If so, the module
 	  will be called ds1682.

 config SPEAR13XX_PCIE_GADGET
 	bool "PCIe gadget support for SPEAr13XX platform"
 	depends on ARCH_SPEAR13XX && BROKEN
 	default n
 	help
 	 This option enables gadget support for PCIe controller. If
 	 board file defines any controller as PCIe endpoint then a sysfs
 	 entry will be created for that controller. User can use these
 	 sysfs node to configure PCIe EP as per his requirements.

 config TI_DAC7512
 	tristate "Texas Instruments DAC7512"
 	depends on SPI && SYSFS
 	help
 	  If you say yes here you get support for the Texas Instruments
 	  DAC7512 16-bit digital-to-analog converter.

 	  This driver can also be built as a module. If so, the module
 	  will be called ti_dac7512.

 config VMWARE_BALLOON
 	tristate "VMware Balloon Driver"
 	depends on VMWARE_VMCI && X86 && HYPERVISOR_GUEST
 	help
 	  This is VMware physical memory management driver which acts
 	  like a "balloon" that can be inflated to reclaim physical pages
 	  by reserving them in the guest and invalidating them in the
 	  monitor, freeing up the underlying machine pages so they can
 	  be allocated to other guests. The balloon can also be deflated
 	  to allow the guest to use more physical memory.

 	  If unsure, say N.

 	  To compile this driver as a module, choose M here: the
 	  module will be called vmw_balloon.

 config PCH_PHUB
 	tristate "Intel EG20T PCH/LAPIS Semicon IOH(ML7213/ML7223/ML7831) PHUB"
 	select GENERIC_NET_UTILS
 	depends on PCI && (X86_32 || MIPS || COMPILE_TEST)
 	help
 	  This driver is for PCH(Platform controller Hub) PHUB(Packet Hub) of
 	  Intel Topcliff which is an IOH(Input/Output Hub) for x86 embedded
 	  processor. The Topcliff has MAC address and Option ROM data in SROM.
 	  This driver can access MAC address and Option ROM data in SROM.

 	  This driver also can be used for LAPIS Semiconductor's IOH,
 	  ML7213/ML7223/ML7831.
 	  ML7213 which is for IVI(In-Vehicle Infotainment) use.
 	  ML7223 IOH is for MP(Media Phone) use.
 	  ML7831 IOH is for general purpose use.
 	  ML7213/ML7223/ML7831 is companion chip for Intel Atom E6xx series.
 	  ML7213/ML7223/ML7831 is completely compatible for Intel EG20T PCH.

 	  To compile this driver as a module, choose M here: the module will
 	  be called pch_phub.

 config USB_SWITCH_FSA9480
 	tristate "FSA9480 USB Switch"
 	depends on I2C
 	help
 	  The FSA9480 is a USB port accessory detector and switch.
 	  The FSA9480 is fully controlled using I2C and enables USB data,
 	  stereo and mono audio, video, microphone and UART data to use
 	  a common connector port.

 config LATTICE_ECP3_CONFIG
 	tristate "Lattice ECP3 FPGA bitstream configuration via SPI"
 	depends on SPI && SYSFS
 	select FW_LOADER
 	default	n
 	help
 	  This option enables support for bitstream configuration (programming
 	  or loading) of the Lattice ECP3 FPGA family via SPI.

 	  If unsure, say N.

 config SRAM
 	bool "Generic on-chip SRAM driver"
 	depends on HAS_IOMEM
 	select GENERIC_ALLOCATOR
 	select SRAM_EXEC if ARM
 	help
 	  This driver allows you to declare a memory region to be managed by
 	  the genalloc API. It is supposed to be used for small on-chip SRAM
 	  areas found on many SoCs.

 config SRAM_EXEC
 	bool

 config VEXPRESS_SYSCFG
 	bool "Versatile Express System Configuration driver"
 	depends on VEXPRESS_CONFIG
 	default y
 	help
 	  ARM Ltd. Versatile Express uses specialised platform configuration
 	  bus. System Configuration interface is one of the possible means
 	  of generating transactions on this bus.

 config ASPEED_LPC_CTRL
 	depends on (ARCH_ASPEED || COMPILE_TEST) && REGMAP && MFD_SYSCON
 	tristate "Aspeed ast2400/2500 HOST LPC to BMC bridge control"
 	---help---
 	  Control Aspeed ast2400/2500 HOST LPC to BMC mappings through
 	  ioctl()s, the driver also provides a read/write interface to a BMC ram
 	  region where the host LPC read/write region can be buffered.

 config ASPEED_LPC_SNOOP
 	tristate "Aspeed ast2500 HOST LPC snoop support"
 	depends on (ARCH_ASPEED || COMPILE_TEST) && REGMAP && MFD_SYSCON
 	help
 	  Provides a driver to control the LPC snoop interface which
 	  allows the BMC to listen on and save the data written by
 	  the host to an arbitrary LPC I/O port.

 config PCI_ENDPOINT_TEST
 	depends on PCI
 	select CRC32
 	tristate "PCI Endpoint Test driver"
 	---help---
            Enable this configuration option to enable the host side test driver
            for PCI Endpoint.

 config UID_SYS_STATS
 	bool "Per-UID statistics"
 	depends on PROFILING && TASK_XACCT && TASK_IO_ACCOUNTING
 	help
 	  Per UID based cpu time statistics exported to /proc/uid_cputime
 	  Per UID based io statistics exported to /proc/uid_io
 	  Per UID based procstat control in /proc/uid_procstat

 config UID_SYS_STATS_DEBUG
 	bool "Per-TASK statistics"
 	depends on UID_SYS_STATS
 	default n
 	help
 	  Per TASK based io statistics exported to /proc/uid_io

 config MEMORY_STATE_TIME
 	tristate "Memory freq/bandwidth time statistics"
 	depends on PROFILING
 	help
 	  Memory time statistics exported to /sys/kernel/memory_state_time

 source "drivers/misc/c2port/Kconfig"
 source "drivers/misc/eeprom/Kconfig"
 source "drivers/misc/cb710/Kconfig"
 source "drivers/misc/ti-st/Kconfig"
 source "drivers/misc/lis3lv02d/Kconfig"
 source "drivers/misc/altera-stapl/Kconfig"
 source "drivers/misc/mei/Kconfig"
 source "drivers/misc/vmw_vmci/Kconfig"
 source "drivers/misc/mic/Kconfig"
 source "drivers/misc/genwqe/Kconfig"
 source "drivers/misc/echo/Kconfig"
 source "drivers/misc/cxl/Kconfig"
 source "drivers/misc/mcu_ipc/Kconfig"
 source "drivers/misc/modem_v1/Kconfig"
 source "drivers/misc/gnss_if/Kconfig"
 source "drivers/misc/tzdev/Kconfig"
 source "drivers/misc/samsung/Kconfig"
 source "drivers/misc/tui/Kconfig"
 endmenu
	#
	# Misc strange devices
	#

	menu "Misc devices"

	config SENSORS_LIS3LV02D
	tristate
	depends on INPUT
	select INPUT_POLLDEV
	default n

	config AD525X_DPOT
	tristate "Analog Devices Digital Potentiometers"
	depends on (I2C \|\| SPI) && SYSFS
	help
	If you say yes here, you get support for the Analog Devices
	AD5258, AD5259, AD5251, AD5252, AD5253, AD5254, AD5255
	AD5160, AD5161, AD5162, AD5165, AD5200, AD5201, AD5203,
	AD5204, AD5206, AD5207, AD5231, AD5232, AD5233, AD5235,
	AD5260, AD5262, AD5263, AD5290, AD5291, AD5292, AD5293,
	AD7376, AD8400, AD8402, AD8403, ADN2850, AD5241, AD5242,
	AD5243, AD5245, AD5246, AD5247, AD5248, AD5280, AD5282,
	ADN2860, AD5273, AD5171, AD5170, AD5172, AD5173, AD5270,
	AD5271, AD5272, AD5274
	digital potentiometer chips.

	See Documentation/misc-devices/ad525x_dpot.txt for the
	userspace interface.

	This driver can also be built as a module. If so, the module
	will be called ad525x_dpot.

	config AD525X_DPOT_I2C
	tristate "support I2C bus connection"
	depends on AD525X_DPOT && I2C
	help
	Say Y here if you have a digital potentiometers hooked to an I2C bus.

	To compile this driver as a module, choose M here: the
	module will be called ad525x_dpot-i2c.

	config AD525X_DPOT_SPI
	tristate "support SPI bus connection"
	depends on AD525X_DPOT && SPI_MASTER
	help
	Say Y here if you have a digital potentiometers hooked to an SPI bus.

	If unsure, say N (but it's safe to say "Y").

	To compile this driver as a module, choose M here: the
	module will be called ad525x_dpot-spi.

	config ATMEL_TCLIB
	bool "Atmel AT32/AT91 Timer/Counter Library"
	depends on (AVR32 \|\| ARCH_AT91)
	help
	Select this if you want a library to allocate the Timer/Counter
	blocks found on many Atmel processors. This facilitates using
	these blocks by different drivers despite processor differences.

	config ATMEL_TCB_CLKSRC
	bool "TC Block Clocksource"
	depends on ATMEL_TCLIB
	default y
	help
	Select this to get a high precision clocksource based on a
	TC block with a 5+ MHz base clock rate. Two timer channels
	are combined to make a single 32-bit timer.

	When GENERIC_CLOCKEVENTS is defined, the third timer channel
	may be used as a clock event device supporting oneshot mode
	(delays of up to two seconds) based on the 32 KiHz clock.

	config ATMEL_TCB_CLKSRC_BLOCK
	int
	depends on ATMEL_TCB_CLKSRC
	prompt "TC Block" if CPU_AT32AP700X
	default 0
	range 0 1
	help
	Some chips provide more than one TC block, so you have the
	choice of which one to use for the clock framework. The other
	TC can be used for other purposes, such as PWM generation and
	interval timing.

	config DUMMY_IRQ
	tristate "Dummy IRQ handler"
	default n
	---help---
	This module accepts a single 'irq' parameter, which it should register for.
	The sole purpose of this module is to help with debugging of systems on
	which spurious IRQs would happen on disabled IRQ vector.

	config IBM_ASM
	tristate "Device driver for IBM RSA service processor"
	depends on X86 && PCI && INPUT
	depends on SERIAL_8250 \|\| SERIAL_8250=n
	---help---
	This option enables device driver support for in-band access to the
	IBM RSA (Condor) service processor in eServer xSeries systems.
	The ibmasm device driver allows user space application to access
	ASM (Advanced Systems Management) functions on the service
	processor. The driver is meant to be used in conjunction with
	a user space API.
	The ibmasm driver also enables the OS to use the UART on the
	service processor board as a regular serial port. To make use of
	this feature serial driver support (CONFIG_SERIAL_8250) must be
	enabled.

	WARNING: This software may not be supported or function
	correctly on your IBM server. Please consult the IBM ServerProven
	website <http://www-03.ibm.com/systems/info/x86servers/serverproven/compat/us/>
	for information on the specific driver level and support statement
	for your IBM server.

	config PHANTOM
	tristate "Sensable PHANToM (PCI)"
	depends on PCI
	help
	Say Y here if you want to build a driver for Sensable PHANToM device.

	This driver is only for PCI PHANToMs.

	If you choose to build module, its name will be phantom. If unsure,
	say N here.

	config INTEL_MID_PTI
	tristate "Parallel Trace Interface for MIPI P1149.7 cJTAG standard"
	depends on PCI && TTY && (X86_INTEL_MID \|\| COMPILE_TEST)
	default n
	help
	The PTI (Parallel Trace Interface) driver directs
	trace data routed from various parts in the system out
	through an Intel Penwell PTI port and out of the mobile
	device for analysis with a debugging tool (Lauterbach or Fido).

	You should select this driver if the target kernel is meant for
	an Intel Atom (non-netbook) mobile device containing a MIPI
	P1149.7 standard implementation.

	config SGI_IOC4
	tristate "SGI IOC4 Base IO support"
	depends on PCI
	---help---
	This option enables basic support for the IOC4 chip on certain
	SGI IO controller cards (IO9, IO10, and PCI-RT). This option
	does not enable any specific functions on such a card, but provides
	necessary infrastructure for other drivers to utilize.

	If you have an SGI Altix with an IOC4-based card say Y.
	Otherwise say N.

	config TIFM_CORE
	tristate "TI Flash Media interface support"
	depends on PCI
	help
	If you want support for Texas Instruments(R) Flash Media adapters
	you should select this option and then also choose an appropriate
	host adapter, such as 'TI Flash Media PCI74xx/PCI76xx host adapter
	support', if you have a TI PCI74xx compatible card reader, for
	example.
	You will also have to select some flash card format drivers. MMC/SD
	cards are supported via 'MMC/SD Card support: TI Flash Media MMC/SD
	Interface support (MMC_TIFM_SD)'.

	To compile this driver as a module, choose M here: the module will
	be called tifm_core.

	config TIFM_7XX1
	tristate "TI Flash Media PCI74xx/PCI76xx host adapter support"
	depends on PCI && TIFM_CORE
	default TIFM_CORE
	help
	This option enables support for Texas Instruments(R) PCI74xx and
	PCI76xx families of Flash Media adapters, found in many laptops.
	To make actual use of the device, you will have to select some
	flash card format drivers, as outlined in the TIFM_CORE Help.

	To compile this driver as a module, choose M here: the module will
	be called tifm_7xx1.

	config ICS932S401
	tristate "Integrated Circuits ICS932S401"
	depends on I2C
	help
	If you say yes here you get support for the Integrated Circuits
	ICS932S401 clock control chips.

	This driver can also be built as a module. If so, the module
	will be called ics932s401.

	config ATMEL_SSC
	tristate "Device driver for Atmel SSC peripheral"
	depends on HAS_IOMEM && (AVR32 \|\| ARCH_AT91 \|\| COMPILE_TEST)
	---help---
	This option enables device driver support for Atmel Synchronized
	Serial Communication peripheral (SSC).

	The SSC peripheral supports a wide variety of serial frame based
	communications, i.e. I2S, SPI, etc.

	If unsure, say N.

	config ENCLOSURE_SERVICES
	tristate "Enclosure Services"
	default n
	help
	Provides support for intelligent enclosures (bays which
	contain storage devices). You also need either a host
	driver (SCSI/ATA) which supports enclosures
	or a SCSI enclosure device (SES) to use these services.

	config SGI_XP
	tristate "Support communication between SGI SSIs"
	depends on NET
	depends on (IA64_GENERIC \|\| IA64_SGI_SN2 \|\| IA64_SGI_UV \|\| X86_UV) && SMP
	select IA64_UNCACHED_ALLOCATOR if IA64_GENERIC \|\| IA64_SGI_SN2
	select GENERIC_ALLOCATOR if IA64_GENERIC \|\| IA64_SGI_SN2
	select SGI_GRU if X86_64 && SMP
	---help---
	An SGI machine can be divided into multiple Single System
	Images which act independently of each other and have
	hardware based memory protection from the others. Enabling
	this feature will allow for direct communication between SSIs
	based on a network adapter and DMA messaging.

	config CS5535_MFGPT
	tristate "CS5535/CS5536 Geode Multi-Function General Purpose Timer (MFGPT) support"
	depends on MFD_CS5535
	default n
	help
	This driver provides access to MFGPT functionality for other
	drivers that need timers. MFGPTs are available in the CS5535 and
	CS5536 companion chips that are found in AMD Geode and several
	other platforms. They have a better resolution and max interval
	than the generic PIT, and are suitable for use as high-res timers.
	You probably don't want to enable this manually; other drivers that
	make use of it should enable it.

	config CS5535_MFGPT_DEFAULT_IRQ
	int
	depends on CS5535_MFGPT
	default 7
	help
	MFGPTs on the CS5535 require an interrupt. The selected IRQ
	can be overridden as a module option as well as by driver that
	use the cs5535_mfgpt_ API; however, different architectures might
	want to use a different IRQ by default. This is here for
	architectures to set as necessary.

	config CS5535_CLOCK_EVENT_SRC
	tristate "CS5535/CS5536 high-res timer (MFGPT) events"
	depends on GENERIC_CLOCKEVENTS && CS5535_MFGPT
	help
	This driver provides a clock event source based on the MFGPT
	timer(s) in the CS5535 and CS5536 companion chips.
	MFGPTs have a better resolution and max interval than the
	generic PIT, and are suitable for use as high-res timers.

	config HP_ILO
	tristate "Channel interface driver for the HP iLO processor"
	depends on PCI
	default n
	help
	The channel interface driver allows applications to communicate
	with iLO management processors present on HP ProLiant servers.
	Upon loading, the driver creates /dev/hpilo/dXccbN files, which
	can be used to gather data from the management processor, via
	read and write system calls.

	To compile this driver as a module, choose M here: the
	module will be called hpilo.

	config QCOM_COINCELL
	tristate "Qualcomm coincell charger support"
	depends on MFD_SPMI_PMIC \|\| COMPILE_TEST
	help
	This driver supports the coincell block found inside of
	Qualcomm PMICs. The coincell charger provides a means to
	charge a coincell battery or backup capacitor which is used
	to maintain PMIC register and RTC state in the absence of
	external power.

	config RT_REGMAP
	tristate "RT Regmap Module"
	default n
	help
	Say Y here to enable RT regmap support.

	config SGI_GRU
	tristate "SGI GRU driver"
	depends on X86_UV && SMP
	default n
	select MMU_NOTIFIER
	---help---
	The GRU is a hardware resource located in the system chipset. The GRU
	contains memory that can be mmapped into the user address space. This memory is
	used to communicate with the GRU to perform functions such as load/store,
	scatter/gather, bcopy, AMOs, etc. The GRU is directly accessed by user
	instructions using user virtual addresses. GRU instructions (ex., bcopy) use
	user virtual addresses for operands.

	If you are not running on a SGI UV system, say N.

	config SGI_GRU_DEBUG
	bool "SGI GRU driver debug"
	depends on SGI_GRU
	default n
	---help---
	This option enables additional debugging code for the SGI GRU driver.
	If you are unsure, say N.

	config APDS9802ALS
	tristate "Medfield Avago APDS9802 ALS Sensor module"
	depends on I2C
	help
	If you say yes here you get support for the ALS APDS9802 ambient
	light sensor.

	This driver can also be built as a module. If so, the module
	will be called apds9802als.

	config ISL29003
	tristate "Intersil ISL29003 ambient light sensor"
	depends on I2C && SYSFS
	help
	If you say yes here you get support for the Intersil ISL29003
	ambient light sensor.

	This driver can also be built as a module. If so, the module
	will be called isl29003.

	config ISL29020
	tristate "Intersil ISL29020 ambient light sensor"
	depends on I2C
	help
	If you say yes here you get support for the Intersil ISL29020
	ambient light sensor.

	This driver can also be built as a module. If so, the module
	will be called isl29020.

	config SENSORS_TSL2550
	tristate "Taos TSL2550 ambient light sensor"
	depends on I2C && SYSFS
	help
	If you say yes here you get support for the Taos TSL2550
	ambient light sensor.

	This driver can also be built as a module. If so, the module
	will be called tsl2550.

	config SENSORS_BH1770
	tristate "BH1770GLC / SFH7770 combined ALS - Proximity sensor"
	depends on I2C
	---help---
	Say Y here if you want to build a driver for BH1770GLC (ROHM) or
	SFH7770 (Osram) combined ambient light and proximity sensor chip.

	To compile this driver as a module, choose M here: the
	module will be called bh1770glc. If unsure, say N here.

	config SENSORS_APDS990X
	tristate "APDS990X combined als and proximity sensors"
	depends on I2C
	default n
	---help---
	Say Y here if you want to build a driver for Avago APDS990x
	combined ambient light and proximity sensor chip.

	To compile this driver as a module, choose M here: the
	module will be called apds990x. If unsure, say N here.

	config HMC6352
	tristate "Honeywell HMC6352 compass"
	depends on I2C
	help
	This driver provides support for the Honeywell HMC6352 compass,
	providing configuration and heading data via sysfs.

	config DS1682
	tristate "Dallas DS1682 Total Elapsed Time Recorder with Alarm"
	depends on I2C
	help
	If you say yes here you get support for Dallas Semiconductor
	DS1682 Total Elapsed Time Recorder.

	This driver can also be built as a module. If so, the module
	will be called ds1682.

	config SPEAR13XX_PCIE_GADGET
	bool "PCIe gadget support for SPEAr13XX platform"
	depends on ARCH_SPEAR13XX && BROKEN
	default n
	help
	This option enables gadget support for PCIe controller. If
	board file defines any controller as PCIe endpoint then a sysfs
	entry will be created for that controller. User can use these
	sysfs node to configure PCIe EP as per his requirements.

	config TI_DAC7512
	tristate "Texas Instruments DAC7512"
	depends on SPI && SYSFS
	help
	If you say yes here you get support for the Texas Instruments
	DAC7512 16-bit digital-to-analog converter.

	This driver can also be built as a module. If so, the module
	will be called ti_dac7512.

	config VMWARE_BALLOON
	tristate "VMware Balloon Driver"
	depends on VMWARE_VMCI && X86 && HYPERVISOR_GUEST
	help
	This is VMware physical memory management driver which acts
	like a "balloon" that can be inflated to reclaim physical pages
	by reserving them in the guest and invalidating them in the
	monitor, freeing up the underlying machine pages so they can
	be allocated to other guests. The balloon can also be deflated
	to allow the guest to use more physical memory.

	If unsure, say N.

	To compile this driver as a module, choose M here: the
	module will be called vmw_balloon.

	config PCH_PHUB
	tristate "Intel EG20T PCH/LAPIS Semicon IOH(ML7213/ML7223/ML7831) PHUB"
	select GENERIC_NET_UTILS
	depends on PCI && (X86_32 \|\| MIPS \|\| COMPILE_TEST)
	help
	This driver is for PCH(Platform controller Hub) PHUB(Packet Hub) of
	Intel Topcliff which is an IOH(Input/Output Hub) for x86 embedded
	processor. The Topcliff has MAC address and Option ROM data in SROM.
	This driver can access MAC address and Option ROM data in SROM.

	This driver also can be used for LAPIS Semiconductor's IOH,
	ML7213/ML7223/ML7831.
	ML7213 which is for IVI(In-Vehicle Infotainment) use.
	ML7223 IOH is for MP(Media Phone) use.
	ML7831 IOH is for general purpose use.
	ML7213/ML7223/ML7831 is companion chip for Intel Atom E6xx series.
	ML7213/ML7223/ML7831 is completely compatible for Intel EG20T PCH.

	To compile this driver as a module, choose M here: the module will
	be called pch_phub.

	config USB_SWITCH_FSA9480
	tristate "FSA9480 USB Switch"
	depends on I2C
	help
	The FSA9480 is a USB port accessory detector and switch.
	The FSA9480 is fully controlled using I2C and enables USB data,
	stereo and mono audio, video, microphone and UART data to use
	a common connector port.

	config LATTICE_ECP3_CONFIG
	tristate "Lattice ECP3 FPGA bitstream configuration via SPI"
	depends on SPI && SYSFS
	select FW_LOADER
	default n
	help
	This option enables support for bitstream configuration (programming
	or loading) of the Lattice ECP3 FPGA family via SPI.

	If unsure, say N.

	config SRAM
	bool "Generic on-chip SRAM driver"
	depends on HAS_IOMEM
	select GENERIC_ALLOCATOR
	select SRAM_EXEC if ARM
	help
	This driver allows you to declare a memory region to be managed by
	the genalloc API. It is supposed to be used for small on-chip SRAM
	areas found on many SoCs.

	config SRAM_EXEC
	bool

	config VEXPRESS_SYSCFG
	bool "Versatile Express System Configuration driver"
	depends on VEXPRESS_CONFIG
	default y
	help
	ARM Ltd. Versatile Express uses specialised platform configuration
	bus. System Configuration interface is one of the possible means
	of generating transactions on this bus.

	config ASPEED_LPC_CTRL
	depends on (ARCH_ASPEED \|\| COMPILE_TEST) && REGMAP && MFD_SYSCON
	tristate "Aspeed ast2400/2500 HOST LPC to BMC bridge control"
	---help---
	Control Aspeed ast2400/2500 HOST LPC to BMC mappings through
	ioctl()s, the driver also provides a read/write interface to a BMC ram
	region where the host LPC read/write region can be buffered.

	config ASPEED_LPC_SNOOP
	tristate "Aspeed ast2500 HOST LPC snoop support"
	depends on (ARCH_ASPEED \|\| COMPILE_TEST) && REGMAP && MFD_SYSCON
	help
	Provides a driver to control the LPC snoop interface which
	allows the BMC to listen on and save the data written by
	the host to an arbitrary LPC I/O port.

	config PCI_ENDPOINT_TEST
	depends on PCI
	select CRC32
	tristate "PCI Endpoint Test driver"
	---help---
	Enable this configuration option to enable the host side test driver
	for PCI Endpoint.

	config UID_SYS_STATS
	bool "Per-UID statistics"
	depends on PROFILING && TASK_XACCT && TASK_IO_ACCOUNTING
	help
	Per UID based cpu time statistics exported to /proc/uid_cputime
	Per UID based io statistics exported to /proc/uid_io
	Per UID based procstat control in /proc/uid_procstat

	config UID_SYS_STATS_DEBUG
	bool "Per-TASK statistics"
	depends on UID_SYS_STATS
	default n
	help
	Per TASK based io statistics exported to /proc/uid_io

	config MEMORY_STATE_TIME
	tristate "Memory freq/bandwidth time statistics"
	depends on PROFILING
	help
	Memory time statistics exported to /sys/kernel/memory_state_time

	source "drivers/misc/c2port/Kconfig"
	source "drivers/misc/eeprom/Kconfig"
	source "drivers/misc/cb710/Kconfig"
	source "drivers/misc/ti-st/Kconfig"
	source "drivers/misc/lis3lv02d/Kconfig"
	source "drivers/misc/altera-stapl/Kconfig"
	source "drivers/misc/mei/Kconfig"
	source "drivers/misc/vmw_vmci/Kconfig"
	source "drivers/misc/mic/Kconfig"
	source "drivers/misc/genwqe/Kconfig"
	source "drivers/misc/echo/Kconfig"
	source "drivers/misc/cxl/Kconfig"
	source "drivers/misc/mcu_ipc/Kconfig"
	source "drivers/misc/modem_v1/Kconfig"
	source "drivers/misc/gnss_if/Kconfig"
	source "drivers/misc/tzdev/Kconfig"
	source "drivers/misc/samsung/Kconfig"
	source "drivers/misc/tui/Kconfig"
	endmenu