| /* |
| * This file is subject to the terms and conditions of the GNU General Public |
| * License. See the file "COPYING" in the main directory of this archive |
| * for more details. |
| * |
| * Derived from IRIX <sys/SN/SN0/hubio.h>, Revision 1.80. |
| * |
| * Copyright (C) 1992 - 1997, 1999 Silicon Graphics, Inc. |
| * Copyright (C) 1999 by Ralf Baechle |
| */ |
| #ifndef _ASM_SGI_SN_SN0_HUBIO_H |
| #define _ASM_SGI_SN_SN0_HUBIO_H |
| |
| /* |
| * Hub I/O interface registers |
| * |
| * All registers in this file are subject to change until Hub chip tapeout. |
| * In general, the longer software name should be used when available. |
| */ |
| |
| /* |
| * Slightly friendlier names for some common registers. |
| * The hardware definitions follow. |
| */ |
| #define IIO_WIDGET IIO_WID /* Widget identification */ |
| #define IIO_WIDGET_STAT IIO_WSTAT /* Widget status register */ |
| #define IIO_WIDGET_CTRL IIO_WCR /* Widget control register */ |
| #define IIO_WIDGET_TOUT IIO_WRTO /* Widget request timeout */ |
| #define IIO_WIDGET_FLUSH IIO_WTFR /* Widget target flush */ |
| #define IIO_PROTECT IIO_ILAPR /* IO interface protection */ |
| #define IIO_PROTECT_OVRRD IIO_ILAPO /* IO protect override */ |
| #define IIO_OUTWIDGET_ACCESS IIO_IOWA /* Outbound widget access */ |
| #define IIO_INWIDGET_ACCESS IIO_IIWA /* Inbound widget access */ |
| #define IIO_INDEV_ERR_MASK IIO_IIDEM /* Inbound device error mask */ |
| #define IIO_LLP_CSR IIO_ILCSR /* LLP control and status */ |
| #define IIO_LLP_LOG IIO_ILLR /* LLP log */ |
| #define IIO_XTALKCC_TOUT IIO_IXCC /* Xtalk credit count timeout*/ |
| #define IIO_XTALKTT_TOUT IIO_IXTT /* Xtalk tail timeout */ |
| #define IIO_IO_ERR_CLR IIO_IECLR /* IO error clear */ |
| #define IIO_BTE_CRB_CNT IIO_IBCN /* IO BTE CRB count */ |
| |
| #define IIO_LLP_CSR_IS_UP 0x00002000 |
| #define IIO_LLP_CSR_LLP_STAT_MASK 0x00003000 |
| #define IIO_LLP_CSR_LLP_STAT_SHFT 12 |
| |
| /* key to IIO_PROTECT_OVRRD */ |
| #define IIO_PROTECT_OVRRD_KEY 0x53474972756c6573ull /* "SGIrules" */ |
| |
| /* BTE register names */ |
| #define IIO_BTE_STAT_0 IIO_IBLS_0 /* Also BTE length/status 0 */ |
| #define IIO_BTE_SRC_0 IIO_IBSA_0 /* Also BTE source address 0 */ |
| #define IIO_BTE_DEST_0 IIO_IBDA_0 /* Also BTE dest. address 0 */ |
| #define IIO_BTE_CTRL_0 IIO_IBCT_0 /* Also BTE control/terminate 0 */ |
| #define IIO_BTE_NOTIFY_0 IIO_IBNA_0 /* Also BTE notification 0 */ |
| #define IIO_BTE_INT_0 IIO_IBIA_0 /* Also BTE interrupt 0 */ |
| #define IIO_BTE_OFF_0 0 /* Base offset from BTE 0 regs. */ |
| #define IIO_BTE_OFF_1 IIO_IBLS_1 - IIO_IBLS_0 /* Offset from base to BTE 1 */ |
| |
| /* BTE register offsets from base */ |
| #define BTEOFF_STAT 0 |
| #define BTEOFF_SRC (IIO_BTE_SRC_0 - IIO_BTE_STAT_0) |
| #define BTEOFF_DEST (IIO_BTE_DEST_0 - IIO_BTE_STAT_0) |
| #define BTEOFF_CTRL (IIO_BTE_CTRL_0 - IIO_BTE_STAT_0) |
| #define BTEOFF_NOTIFY (IIO_BTE_NOTIFY_0 - IIO_BTE_STAT_0) |
| #define BTEOFF_INT (IIO_BTE_INT_0 - IIO_BTE_STAT_0) |
| |
| |
| /* |
| * The following definitions use the names defined in the IO interface |
| * document for ease of reference. When possible, software should |
| * generally use the longer but clearer names defined above. |
| */ |
| |
| #define IIO_BASE 0x400000 |
| #define IIO_BASE_BTE0 0x410000 |
| #define IIO_BASE_BTE1 0x420000 |
| #define IIO_BASE_PERF 0x430000 |
| #define IIO_PERF_CNT 0x430008 |
| |
| #define IO_PERF_SETS 32 |
| |
| #define IIO_WID 0x400000 /* Widget identification */ |
| #define IIO_WSTAT 0x400008 /* Widget status */ |
| #define IIO_WCR 0x400020 /* Widget control */ |
| |
| #define IIO_WSTAT_ECRAZY (1ULL << 32) /* Hub gone crazy */ |
| #define IIO_WSTAT_TXRETRY (1ULL << 9) /* Hub Tx Retry timeout */ |
| #define IIO_WSTAT_TXRETRY_MASK (0x7F) |
| #define IIO_WSTAT_TXRETRY_SHFT (16) |
| #define IIO_WSTAT_TXRETRY_CNT(w) (((w) >> IIO_WSTAT_TXRETRY_SHFT) & \ |
| IIO_WSTAT_TXRETRY_MASK) |
| |
| #define IIO_ILAPR 0x400100 /* Local Access Protection */ |
| #define IIO_ILAPO 0x400108 /* Protection override */ |
| #define IIO_IOWA 0x400110 /* outbound widget access */ |
| #define IIO_IIWA 0x400118 /* inbound widget access */ |
| #define IIO_IIDEM 0x400120 /* Inbound Device Error Mask */ |
| #define IIO_ILCSR 0x400128 /* LLP control and status */ |
| #define IIO_ILLR 0x400130 /* LLP Log */ |
| #define IIO_IIDSR 0x400138 /* Interrupt destination */ |
| |
| #define IIO_IIBUSERR 0x1400208 /* Reads here cause a bus error. */ |
| |
| /* IO Interrupt Destination Register */ |
| #define IIO_IIDSR_SENT_SHIFT 28 |
| #define IIO_IIDSR_SENT_MASK 0x10000000 |
| #define IIO_IIDSR_ENB_SHIFT 24 |
| #define IIO_IIDSR_ENB_MASK 0x01000000 |
| #define IIO_IIDSR_NODE_SHIFT 8 |
| #define IIO_IIDSR_NODE_MASK 0x0000ff00 |
| #define IIO_IIDSR_LVL_SHIFT 0 |
| #define IIO_IIDSR_LVL_MASK 0x0000003f |
| |
| |
| /* GFX Flow Control Node/Widget Register */ |
| #define IIO_IGFX_0 0x400140 /* gfx node/widget register 0 */ |
| #define IIO_IGFX_1 0x400148 /* gfx node/widget register 1 */ |
| #define IIO_IGFX_W_NUM_BITS 4 /* size of widget num field */ |
| #define IIO_IGFX_W_NUM_MASK ((1<<IIO_IGFX_W_NUM_BITS)-1) |
| #define IIO_IGFX_W_NUM_SHIFT 0 |
| #define IIO_IGFX_N_NUM_BITS 9 /* size of node num field */ |
| #define IIO_IGFX_N_NUM_MASK ((1<<IIO_IGFX_N_NUM_BITS)-1) |
| #define IIO_IGFX_N_NUM_SHIFT 4 |
| #define IIO_IGFX_P_NUM_BITS 1 /* size of processor num field */ |
| #define IIO_IGFX_P_NUM_MASK ((1<<IIO_IGFX_P_NUM_BITS)-1) |
| #define IIO_IGFX_P_NUM_SHIFT 16 |
| #define IIO_IGFX_VLD_BITS 1 /* size of valid field */ |
| #define IIO_IGFX_VLD_MASK ((1<<IIO_IGFX_VLD_BITS)-1) |
| #define IIO_IGFX_VLD_SHIFT 20 |
| #define IIO_IGFX_INIT(widget, node, cpu, valid) (\ |
| (((widget) & IIO_IGFX_W_NUM_MASK) << IIO_IGFX_W_NUM_SHIFT) | \ |
| (((node) & IIO_IGFX_N_NUM_MASK) << IIO_IGFX_N_NUM_SHIFT) | \ |
| (((cpu) & IIO_IGFX_P_NUM_MASK) << IIO_IGFX_P_NUM_SHIFT) | \ |
| (((valid) & IIO_IGFX_VLD_MASK) << IIO_IGFX_VLD_SHIFT) ) |
| |
| /* Scratch registers (not all bits available) */ |
| #define IIO_SCRATCH_REG0 0x400150 |
| #define IIO_SCRATCH_REG1 0x400158 |
| #define IIO_SCRATCH_MASK 0x0000000f00f11fff |
| |
| #define IIO_SCRATCH_BIT0_0 0x0000000800000000 |
| #define IIO_SCRATCH_BIT0_1 0x0000000400000000 |
| #define IIO_SCRATCH_BIT0_2 0x0000000200000000 |
| #define IIO_SCRATCH_BIT0_3 0x0000000100000000 |
| #define IIO_SCRATCH_BIT0_4 0x0000000000800000 |
| #define IIO_SCRATCH_BIT0_5 0x0000000000400000 |
| #define IIO_SCRATCH_BIT0_6 0x0000000000200000 |
| #define IIO_SCRATCH_BIT0_7 0x0000000000100000 |
| #define IIO_SCRATCH_BIT0_8 0x0000000000010000 |
| #define IIO_SCRATCH_BIT0_9 0x0000000000001000 |
| #define IIO_SCRATCH_BIT0_R 0x0000000000000fff |
| |
| /* IO Translation Table Entries */ |
| #define IIO_NUM_ITTES 7 /* ITTEs numbered 0..6 */ |
| /* Hw manuals number them 1..7! */ |
| |
| /* |
| * As a permanent workaround for a bug in the PI side of the hub, we've |
| * redefined big window 7 as small window 0. |
| */ |
| #define HUB_NUM_BIG_WINDOW IIO_NUM_ITTES - 1 |
| |
| /* |
| * Use the top big window as a surrogate for the first small window |
| */ |
| #define SWIN0_BIGWIN HUB_NUM_BIG_WINDOW |
| |
| #define ILCSR_WARM_RESET 0x100 |
| /* |
| * The IO LLP control status register and widget control register |
| */ |
| #ifndef __ASSEMBLY__ |
| |
| typedef union hubii_wid_u { |
| u64 wid_reg_value; |
| struct { |
| u64 wid_rsvd: 32, /* unused */ |
| wid_rev_num: 4, /* revision number */ |
| wid_part_num: 16, /* the widget type: hub=c101 */ |
| wid_mfg_num: 11, /* Manufacturer id (IBM) */ |
| wid_rsvd1: 1; /* Reserved */ |
| } wid_fields_s; |
| } hubii_wid_t; |
| |
| |
| typedef union hubii_wcr_u { |
| u64 wcr_reg_value; |
| struct { |
| u64 wcr_rsvd: 41, /* unused */ |
| wcr_e_thresh: 5, /* elasticity threshold */ |
| wcr_dir_con: 1, /* widget direct connect */ |
| wcr_f_bad_pkt: 1, /* Force bad llp pkt enable */ |
| wcr_xbar_crd: 3, /* LLP crossbar credit */ |
| wcr_rsvd1: 8, /* Reserved */ |
| wcr_tag_mode: 1, /* Tag mode */ |
| wcr_widget_id: 4; /* LLP crossbar credit */ |
| } wcr_fields_s; |
| } hubii_wcr_t; |
| |
| #define iwcr_dir_con wcr_fields_s.wcr_dir_con |
| |
| typedef union hubii_wstat_u { |
| u64 reg_value; |
| struct { |
| u64 rsvd1: 31, |
| crazy: 1, /* Crazy bit */ |
| rsvd2: 8, |
| llp_tx_cnt: 8, /* LLP Xmit retry counter */ |
| rsvd3: 6, |
| tx_max_rtry: 1, /* LLP Retry Timeout Signal */ |
| rsvd4: 2, |
| xt_tail_to: 1, /* Xtalk Tail Timeout */ |
| xt_crd_to: 1, /* Xtalk Credit Timeout */ |
| pending: 4; /* Pending Requests */ |
| } wstat_fields_s; |
| } hubii_wstat_t; |
| |
| |
| typedef union hubii_ilcsr_u { |
| u64 icsr_reg_value; |
| struct { |
| u64 icsr_rsvd: 22, /* unused */ |
| icsr_max_burst: 10, /* max burst */ |
| icsr_rsvd4: 6, /* reserved */ |
| icsr_max_retry: 10, /* max retry */ |
| icsr_rsvd3: 2, /* reserved */ |
| icsr_lnk_stat: 2, /* link status */ |
| icsr_bm8: 1, /* Bit mode 8 */ |
| icsr_llp_en: 1, /* LLP enable bit */ |
| icsr_rsvd2: 1, /* reserver */ |
| icsr_wrm_reset: 1, /* Warm reset bit */ |
| icsr_rsvd1: 2, /* Data ready offset */ |
| icsr_null_to: 6; /* Null timeout */ |
| |
| } icsr_fields_s; |
| } hubii_ilcsr_t; |
| |
| |
| typedef union hubii_iowa_u { |
| u64 iowa_reg_value; |
| struct { |
| u64 iowa_rsvd: 48, /* unused */ |
| iowa_wxoac: 8, /* xtalk widget access bits */ |
| iowa_rsvd1: 7, /* xtalk widget access bits */ |
| iowa_w0oac: 1; /* xtalk widget access bits */ |
| } iowa_fields_s; |
| } hubii_iowa_t; |
| |
| typedef union hubii_iiwa_u { |
| u64 iiwa_reg_value; |
| struct { |
| u64 iiwa_rsvd: 48, /* unused */ |
| iiwa_wxiac: 8, /* hub wid access bits */ |
| iiwa_rsvd1: 7, /* reserved */ |
| iiwa_w0iac: 1; /* hub wid0 access */ |
| } iiwa_fields_s; |
| } hubii_iiwa_t; |
| |
| typedef union hubii_illr_u { |
| u64 illr_reg_value; |
| struct { |
| u64 illr_rsvd: 32, /* unused */ |
| illr_cb_cnt: 16, /* checkbit error count */ |
| illr_sn_cnt: 16; /* sequence number count */ |
| } illr_fields_s; |
| } hubii_illr_t; |
| |
| /* The structures below are defined to extract and modify the ii |
| performance registers */ |
| |
| /* io_perf_sel allows the caller to specify what tests will be |
| performed */ |
| typedef union io_perf_sel { |
| u64 perf_sel_reg; |
| struct { |
| u64 perf_rsvd : 48, |
| perf_icct : 8, |
| perf_ippr1 : 4, |
| perf_ippr0 : 4; |
| } perf_sel_bits; |
| } io_perf_sel_t; |
| |
| /* io_perf_cnt is to extract the count from the hub registers. Due to |
| hardware problems there is only one counter, not two. */ |
| |
| typedef union io_perf_cnt { |
| u64 perf_cnt; |
| struct { |
| u64 perf_rsvd1 : 32, |
| perf_rsvd2 : 12, |
| perf_cnt : 20; |
| } perf_cnt_bits; |
| } io_perf_cnt_t; |
| |
| #endif /* !__ASSEMBLY__ */ |
| |
| |
| #define LNK_STAT_WORKING 0x2 |
| |
| #define IIO_LLP_CB_MAX 0xffff |
| #define IIO_LLP_SN_MAX 0xffff |
| |
| /* IO PRB Entries */ |
| #define IIO_NUM_IPRBS (9) |
| #define IIO_IOPRB_0 0x400198 /* PRB entry 0 */ |
| #define IIO_IOPRB_8 0x4001a0 /* PRB entry 8 */ |
| #define IIO_IOPRB_9 0x4001a8 /* PRB entry 9 */ |
| #define IIO_IOPRB_A 0x4001b0 /* PRB entry a */ |
| #define IIO_IOPRB_B 0x4001b8 /* PRB entry b */ |
| #define IIO_IOPRB_C 0x4001c0 /* PRB entry c */ |
| #define IIO_IOPRB_D 0x4001c8 /* PRB entry d */ |
| #define IIO_IOPRB_E 0x4001d0 /* PRB entry e */ |
| #define IIO_IOPRB_F 0x4001d8 /* PRB entry f */ |
| |
| |
| #define IIO_IXCC 0x4001e0 /* Crosstalk credit count timeout */ |
| #define IIO_IXTCC IIO_IXCC |
| #define IIO_IMEM 0x4001e8 /* Miscellaneous Enable Mask */ |
| #define IIO_IXTT 0x4001f0 /* Crosstalk tail timeout */ |
| #define IIO_IECLR 0x4001f8 /* IO error clear */ |
| #define IIO_IBCN 0x400200 /* IO BTE CRB count */ |
| |
| /* |
| * IIO_IMEM Register fields. |
| */ |
| #define IIO_IMEM_W0ESD 0x1 /* Widget 0 shut down due to error */ |
| #define IIO_IMEM_B0ESD (1 << 4) /* BTE 0 shut down due to error */ |
| #define IIO_IMEM_B1ESD (1 << 8) /* BTE 1 Shut down due to error */ |
| |
| /* PIO Read address Table Entries */ |
| #define IIO_IPCA 0x400300 /* PRB Counter adjust */ |
| #define IIO_NUM_PRTES 8 /* Total number of PRB table entries */ |
| #define IIO_PRTE_0 0x400308 /* PIO Read address table entry 0 */ |
| #define IIO_PRTE(_x) (IIO_PRTE_0 + (8 * (_x))) |
| #define IIO_WIDPRTE(x) IIO_PRTE(((x) - 8)) /* widget ID to its PRTE num */ |
| #define IIO_IPDR 0x400388 /* PIO table entry deallocation */ |
| #define IIO_ICDR 0x400390 /* CRB Entry Deallocation */ |
| #define IIO_IFDR 0x400398 /* IOQ FIFO Depth */ |
| #define IIO_IIAP 0x4003a0 /* IIQ Arbitration Parameters */ |
| #define IIO_IMMR IIO_IIAP |
| #define IIO_ICMR 0x4003a8 /* CRB Managment Register */ |
| #define IIO_ICCR 0x4003b0 /* CRB Control Register */ |
| #define IIO_ICTO 0x4003b8 /* CRB Time Out Register */ |
| #define IIO_ICTP 0x4003c0 /* CRB Time Out Prescalar */ |
| |
| |
| /* |
| * ICMR register fields |
| */ |
| #define IIO_ICMR_PC_VLD_SHFT 36 |
| #define IIO_ICMR_PC_VLD_MASK (0x7fffUL << IIO_ICMR_PC_VLD_SHFT) |
| |
| #define IIO_ICMR_CRB_VLD_SHFT 20 |
| #define IIO_ICMR_CRB_VLD_MASK (0x7fffUL << IIO_ICMR_CRB_VLD_SHFT) |
| |
| #define IIO_ICMR_FC_CNT_SHFT 16 |
| #define IIO_ICMR_FC_CNT_MASK (0xf << IIO_ICMR_FC_CNT_SHFT) |
| |
| #define IIO_ICMR_C_CNT_SHFT 4 |
| #define IIO_ICMR_C_CNT_MASK (0xf << IIO_ICMR_C_CNT_SHFT) |
| |
| #define IIO_ICMR_P_CNT_SHFT 0 |
| #define IIO_ICMR_P_CNT_MASK (0xf << IIO_ICMR_P_CNT_SHFT) |
| |
| #define IIO_ICMR_PRECISE (1UL << 52) |
| #define IIO_ICMR_CLR_RPPD (1UL << 13) |
| #define IIO_ICMR_CLR_RQPD (1UL << 12) |
| |
| /* |
| * IIO PIO Deallocation register field masks : (IIO_IPDR) |
| */ |
| #define IIO_IPDR_PND (1 << 4) |
| |
| /* |
| * IIO CRB deallocation register field masks: (IIO_ICDR) |
| */ |
| #define IIO_ICDR_PND (1 << 4) |
| |
| /* |
| * IIO CRB control register Fields: IIO_ICCR |
| */ |
| #define IIO_ICCR_PENDING (0x10000) |
| #define IIO_ICCR_CMD_MASK (0xFF) |
| #define IIO_ICCR_CMD_SHFT (7) |
| #define IIO_ICCR_CMD_NOP (0x0) /* No Op */ |
| #define IIO_ICCR_CMD_WAKE (0x100) /* Reactivate CRB entry and process */ |
| #define IIO_ICCR_CMD_TIMEOUT (0x200) /* Make CRB timeout & mark invalid */ |
| #define IIO_ICCR_CMD_EJECT (0x400) /* Contents of entry written to memory |
| * via a WB |
| */ |
| #define IIO_ICCR_CMD_FLUSH (0x800) |
| |
| /* |
| * CRB manipulation macros |
| * The CRB macros are slightly complicated, since there are up to |
| * four registers associated with each CRB entry. |
| */ |
| #define IIO_NUM_CRBS 15 /* Number of CRBs */ |
| #define IIO_NUM_NORMAL_CRBS 12 /* Number of regular CRB entries */ |
| #define IIO_NUM_PC_CRBS 4 /* Number of partial cache CRBs */ |
| #define IIO_ICRB_OFFSET 8 |
| #define IIO_ICRB_0 0x400400 |
| /* XXX - This is now tuneable: |
| #define IIO_FIRST_PC_ENTRY 12 |
| */ |
| |
| #define IIO_ICRB_A(_x) (IIO_ICRB_0 + (4 * IIO_ICRB_OFFSET * (_x))) |
| #define IIO_ICRB_B(_x) (IIO_ICRB_A(_x) + 1*IIO_ICRB_OFFSET) |
| #define IIO_ICRB_C(_x) (IIO_ICRB_A(_x) + 2*IIO_ICRB_OFFSET) |
| #define IIO_ICRB_D(_x) (IIO_ICRB_A(_x) + 3*IIO_ICRB_OFFSET) |
| |
| /* XXX - IBUE register coming for Hub 2 */ |
| |
| /* |
| * |
| * CRB Register description. |
| * |
| * WARNING * WARNING * WARNING * WARNING * WARNING * WARNING * WARNING |
| * WARNING * WARNING * WARNING * WARNING * WARNING * WARNING * WARNING |
| * WARNING * WARNING * WARNING * WARNING * WARNING * WARNING * WARNING |
| * WARNING * WARNING * WARNING * WARNING * WARNING * WARNING * WARNING |
| * WARNING * WARNING * WARNING * WARNING * WARNING * WARNING * WARNING |
| * |
| * Many of the fields in CRB are status bits used by hardware |
| * for implementation of the protocol. It's very dangerous to |
| * mess around with the CRB registers. |
| * |
| * It's OK to read the CRB registers and try to make sense out of the |
| * fields in CRB. |
| * |
| * Updating CRB requires all activities in Hub IIO to be quiesced. |
| * otherwise, a write to CRB could corrupt other CRB entries. |
| * CRBs are here only as a back door peek to hub IIO's status. |
| * Quiescing implies no dmas no PIOs |
| * either directly from the cpu or from sn0net. |
| * this is not something that can be done easily. So, AVOID updating |
| * CRBs. |
| */ |
| |
| /* |
| * Fields in CRB Register A |
| */ |
| #ifndef __ASSEMBLY__ |
| typedef union icrba_u { |
| u64 reg_value; |
| struct { |
| u64 resvd: 6, |
| stall_bte0: 1, /* Stall BTE 0 */ |
| stall_bte1: 1, /* Stall BTE 1 */ |
| error: 1, /* CRB has an error */ |
| ecode: 3, /* Error Code */ |
| lnetuce: 1, /* SN0net Uncorrectable error */ |
| mark: 1, /* CRB Has been marked */ |
| xerr: 1, /* Error bit set in xtalk header */ |
| sidn: 4, /* SIDN field from xtalk */ |
| tnum: 5, /* TNUM field in xtalk */ |
| addr: 38, /* Address of request */ |
| valid: 1, /* Valid status */ |
| iow: 1; /* IO Write operation */ |
| } icrba_fields_s; |
| } icrba_t; |
| |
| /* This is an alternate typedef for the HUB1 CRB A in order to allow |
| runtime selection of the format based on the REV_ID field of the |
| NI_STATUS_REV_ID register. */ |
| typedef union h1_icrba_u { |
| u64 reg_value; |
| |
| struct { |
| u64 resvd: 6, |
| unused: 1, /* Unused but RW!! */ |
| error: 1, /* CRB has an error */ |
| ecode: 4, /* Error Code */ |
| lnetuce: 1, /* SN0net Uncorrectable error */ |
| mark: 1, /* CRB Has been marked */ |
| xerr: 1, /* Error bit set in xtalk header */ |
| sidn: 4, /* SIDN field from xtalk */ |
| tnum: 5, /* TNUM field in xtalk */ |
| addr: 38, /* Address of request */ |
| valid: 1, /* Valid status */ |
| iow: 1; /* IO Write operation */ |
| } h1_icrba_fields_s; |
| } h1_icrba_t; |
| |
| /* XXX - Is this still right? Check the spec. */ |
| #define ICRBN_A_CERR_SHFT 54 |
| #define ICRBN_A_ERR_MASK 0x3ff |
| |
| #if 0 /* Disabled, this causes namespace polution and break allmodconfig */ |
| /* |
| * Easy access macros. |
| */ |
| #define a_error icrba_fields_s.error |
| #define a_ecode icrba_fields_s.ecode |
| #define a_lnetuce icrba_fields_s.lnetuce |
| #define a_mark icrba_fields_s.mark |
| #define a_xerr icrba_fields_s.xerr |
| #define a_sidn icrba_fields_s.sidn |
| #define a_tnum icrba_fields_s.tnum |
| #define a_addr icrba_fields_s.addr |
| #define a_valid icrba_fields_s.valid |
| #define a_iow icrba_fields_s.iow |
| #endif |
| |
| #endif /* !__ASSEMBLY__ */ |
| |
| #define IIO_ICRB_ADDR_SHFT 2 /* Shift to get proper address */ |
| |
| /* |
| * values for "ecode" field |
| */ |
| #define IIO_ICRB_ECODE_DERR 0 /* Directory error due to IIO access */ |
| #define IIO_ICRB_ECODE_PERR 1 /* Poison error on IO access */ |
| #define IIO_ICRB_ECODE_WERR 2 /* Write error by IIO access |
| * e.g. WINV to a Read only line. |
| */ |
| #define IIO_ICRB_ECODE_AERR 3 /* Access error caused by IIO access */ |
| #define IIO_ICRB_ECODE_PWERR 4 /* Error on partial write */ |
| #define IIO_ICRB_ECODE_PRERR 5 /* Error on partial read */ |
| #define IIO_ICRB_ECODE_TOUT 6 /* CRB timeout before deallocating */ |
| #define IIO_ICRB_ECODE_XTERR 7 /* Incoming xtalk pkt had error bit */ |
| |
| |
| |
| /* |
| * Fields in CRB Register B |
| */ |
| #ifndef __ASSEMBLY__ |
| typedef union icrbb_u { |
| u64 reg_value; |
| struct { |
| u64 rsvd1: 5, |
| btenum: 1, /* BTE to which entry belongs to */ |
| cohtrans: 1, /* Coherent transaction */ |
| xtsize: 2, /* Xtalk operation size |
| * 0: Double Word |
| * 1: 32 Bytes. |
| * 2: 128 Bytes, |
| * 3: Reserved. |
| */ |
| srcnode: 9, /* Source Node ID */ |
| srcinit: 2, /* Source Initiator: |
| * See below for field values. |
| */ |
| useold: 1, /* Use OLD command for processing */ |
| imsgtype: 2, /* Incoming message type |
| * see below for field values |
| */ |
| imsg: 8, /* Incoming message */ |
| initator: 3, /* Initiator of original request |
| * See below for field values. |
| */ |
| reqtype: 5, /* Identifies type of request |
| * See below for field values. |
| */ |
| rsvd2: 7, |
| ackcnt: 11, /* Invalidate ack count */ |
| resp: 1, /* data response given to processor */ |
| ack: 1, /* indicates data ack received */ |
| hold: 1, /* entry is gathering inval acks */ |
| wb_pend:1, /* waiting for writeback to complete */ |
| intvn: 1, /* Intervention */ |
| stall_ib: 1, /* Stall Ibuf (from crosstalk) */ |
| stall_intr: 1; /* Stall internal interrupts */ |
| } icrbb_field_s; |
| } icrbb_t; |
| |
| /* This is an alternate typedef for the HUB1 CRB B in order to allow |
| runtime selection of the format based on the REV_ID field of the |
| NI_STATUS_REV_ID register. */ |
| typedef union h1_icrbb_u { |
| u64 reg_value; |
| struct { |
| u64 rsvd1: 5, |
| btenum: 1, /* BTE to which entry belongs to */ |
| cohtrans: 1, /* Coherent transaction */ |
| xtsize: 2, /* Xtalk operation size |
| * 0: Double Word |
| * 1: 32 Bytes. |
| * 2: 128 Bytes, |
| * 3: Reserved. |
| */ |
| srcnode: 9, /* Source Node ID */ |
| srcinit: 2, /* Source Initiator: |
| * See below for field values. |
| */ |
| useold: 1, /* Use OLD command for processing */ |
| imsgtype: 2, /* Incoming message type |
| * see below for field values |
| */ |
| imsg: 8, /* Incoming message */ |
| initator: 3, /* Initiator of original request |
| * See below for field values. |
| */ |
| rsvd2: 1, |
| pcache: 1, /* entry belongs to partial cache */ |
| reqtype: 5, /* Identifies type of request |
| * See below for field values. |
| */ |
| stl_ib: 1, /* stall Ibus coming from xtalk */ |
| stl_intr: 1, /* Stall internal interrupts */ |
| stl_bte0: 1, /* Stall BTE 0 */ |
| stl_bte1: 1, /* Stall BTE 1 */ |
| intrvn: 1, /* Req was target of intervention */ |
| ackcnt: 11, /* Invalidate ack count */ |
| resp: 1, /* data response given to processor */ |
| ack: 1, /* indicates data ack received */ |
| hold: 1, /* entry is gathering inval acks */ |
| wb_pend:1, /* waiting for writeback to complete */ |
| sleep: 1, /* xtalk req sleeping till IO-sync */ |
| pnd_reply: 1, /* replies not issed due to IOQ full */ |
| pnd_req: 1; /* reqs not issued due to IOQ full */ |
| } h1_icrbb_field_s; |
| } h1_icrbb_t; |
| |
| |
| #define b_imsgtype icrbb_field_s.imsgtype |
| #define b_btenum icrbb_field_s.btenum |
| #define b_cohtrans icrbb_field_s.cohtrans |
| #define b_xtsize icrbb_field_s.xtsize |
| #define b_srcnode icrbb_field_s.srcnode |
| #define b_srcinit icrbb_field_s.srcinit |
| #define b_imsgtype icrbb_field_s.imsgtype |
| #define b_imsg icrbb_field_s.imsg |
| #define b_initiator icrbb_field_s.initiator |
| |
| #endif /* !__ASSEMBLY__ */ |
| |
| /* |
| * values for field xtsize |
| */ |
| #define IIO_ICRB_XTSIZE_DW 0 /* Xtalk operation size is 8 bytes */ |
| #define IIO_ICRB_XTSIZE_32 1 /* Xtalk operation size is 32 bytes */ |
| #define IIO_ICRB_XTSIZE_128 2 /* Xtalk operation size is 128 bytes */ |
| |
| /* |
| * values for field srcinit |
| */ |
| #define IIO_ICRB_PROC0 0 /* Source of request is Proc 0 */ |
| #define IIO_ICRB_PROC1 1 /* Source of request is Proc 1 */ |
| #define IIO_ICRB_GB_REQ 2 /* Source is Guranteed BW request */ |
| #define IIO_ICRB_IO_REQ 3 /* Source is Normal IO request */ |
| |
| /* |
| * Values for field imsgtype |
| */ |
| #define IIO_ICRB_IMSGT_XTALK 0 /* Incoming Meessage from Xtalk */ |
| #define IIO_ICRB_IMSGT_BTE 1 /* Incoming message from BTE */ |
| #define IIO_ICRB_IMSGT_SN0NET 2 /* Incoming message from SN0 net */ |
| #define IIO_ICRB_IMSGT_CRB 3 /* Incoming message from CRB ??? */ |
| |
| /* |
| * values for field initiator. |
| */ |
| #define IIO_ICRB_INIT_XTALK 0 /* Message originated in xtalk */ |
| #define IIO_ICRB_INIT_BTE0 0x1 /* Message originated in BTE 0 */ |
| #define IIO_ICRB_INIT_SN0NET 0x2 /* Message originated in SN0net */ |
| #define IIO_ICRB_INIT_CRB 0x3 /* Message originated in CRB ? */ |
| #define IIO_ICRB_INIT_BTE1 0x5 /* MEssage originated in BTE 1 */ |
| |
| /* |
| * Values for field reqtype. |
| */ |
| /* XXX - Need to fix this for Hub 2 */ |
| #define IIO_ICRB_REQ_DWRD 0 /* Request type double word */ |
| #define IIO_ICRB_REQ_QCLRD 1 /* Request is Qrtr Caceh line Rd */ |
| #define IIO_ICRB_REQ_BLKRD 2 /* Request is block read */ |
| #define IIO_ICRB_REQ_RSHU 6 /* Request is BTE block read */ |
| #define IIO_ICRB_REQ_REXU 7 /* request is BTE Excl Read */ |
| #define IIO_ICRB_REQ_RDEX 8 /* Request is Read Exclusive */ |
| #define IIO_ICRB_REQ_WINC 9 /* Request is Write Invalidate */ |
| #define IIO_ICRB_REQ_BWINV 10 /* Request is BTE Winv */ |
| #define IIO_ICRB_REQ_PIORD 11 /* Request is PIO read */ |
| #define IIO_ICRB_REQ_PIOWR 12 /* Request is PIO Write */ |
| #define IIO_ICRB_REQ_PRDM 13 /* Request is Fetch&Op */ |
| #define IIO_ICRB_REQ_PWRM 14 /* Request is Store &Op */ |
| #define IIO_ICRB_REQ_PTPWR 15 /* Request is Peer to peer */ |
| #define IIO_ICRB_REQ_WB 16 /* Request is Write back */ |
| #define IIO_ICRB_REQ_DEX 17 /* Retained DEX Cache line */ |
| |
| /* |
| * Fields in CRB Register C |
| */ |
| |
| #ifndef __ASSEMBLY__ |
| |
| typedef union icrbc_s { |
| u64 reg_value; |
| struct { |
| u64 rsvd: 6, |
| sleep: 1, |
| pricnt: 4, /* Priority count sent with Read req */ |
| pripsc: 4, /* Priority Pre scalar */ |
| bteop: 1, /* BTE Operation */ |
| push_be: 34, /* Push address Byte enable |
| * Holds push addr, if CRB is for BTE |
| * If CRB belongs to Partial cache, |
| * this contains byte enables bits |
| * ([47:46] = 0) |
| */ |
| suppl: 11, /* Supplemental field */ |
| barrop: 1, /* Barrier Op bit set in xtalk req */ |
| doresp: 1, /* Xtalk req needs a response */ |
| gbr: 1; /* GBR bit set in xtalk packet */ |
| } icrbc_field_s; |
| } icrbc_t; |
| |
| #define c_pricnt icrbc_field_s.pricnt |
| #define c_pripsc icrbc_field_s.pripsc |
| #define c_bteop icrbc_field_s.bteop |
| #define c_bteaddr icrbc_field_s.push_be /* push_be field has 2 names */ |
| #define c_benable icrbc_field_s.push_be /* push_be field has 2 names */ |
| #define c_suppl icrbc_field_s.suppl |
| #define c_barrop icrbc_field_s.barrop |
| #define c_doresp icrbc_field_s.doresp |
| #define c_gbr icrbc_field_s.gbr |
| #endif /* !__ASSEMBLY__ */ |
| |
| /* |
| * Fields in CRB Register D |
| */ |
| |
| #ifndef __ASSEMBLY__ |
| typedef union icrbd_s { |
| u64 reg_value; |
| struct { |
| u64 rsvd: 38, |
| toutvld: 1, /* Timeout in progress for this CRB */ |
| ctxtvld: 1, /* Context field below is valid */ |
| rsvd2: 1, |
| context: 15, /* Bit vector: |
| * Has a bit set for each CRB entry |
| * which needs to be deallocated |
| * before this CRB entry is processed. |
| * Set only for barrier operations. |
| */ |
| timeout: 8; /* Timeout Upper 8 bits */ |
| } icrbd_field_s; |
| } icrbd_t; |
| |
| #define icrbd_toutvld icrbd_field_s.toutvld |
| #define icrbd_ctxtvld icrbd_field_s.ctxtvld |
| #define icrbd_context icrbd_field_s.context |
| |
| |
| typedef union hubii_ifdr_u { |
| u64 hi_ifdr_value; |
| struct { |
| u64 ifdr_rsvd: 49, |
| ifdr_maxrp: 7, |
| ifdr_rsvd1: 1, |
| ifdr_maxrq: 7; |
| } hi_ifdr_fields; |
| } hubii_ifdr_t; |
| |
| #endif /* !__ASSEMBLY__ */ |
| |
| /* |
| * Hardware designed names for the BTE control registers. |
| */ |
| #define IIO_IBLS_0 0x410000 /* BTE length/status 0 */ |
| #define IIO_IBSA_0 0x410008 /* BTE source address 0 */ |
| #define IIO_IBDA_0 0x410010 /* BTE destination address 0 */ |
| #define IIO_IBCT_0 0x410018 /* BTE control/terminate 0 */ |
| #define IIO_IBNA_0 0x410020 /* BTE notification address 0 */ |
| #define IIO_IBNR_0 IIO_IBNA_0 |
| #define IIO_IBIA_0 0x410028 /* BTE interrupt address 0 */ |
| |
| #define IIO_IBLS_1 0x420000 /* BTE length/status 1 */ |
| #define IIO_IBSA_1 0x420008 /* BTE source address 1 */ |
| #define IIO_IBDA_1 0x420010 /* BTE destination address 1 */ |
| #define IIO_IBCT_1 0x420018 /* BTE control/terminate 1 */ |
| #define IIO_IBNA_1 0x420020 /* BTE notification address 1 */ |
| #define IIO_IBNR_1 IIO_IBNA_1 |
| #define IIO_IBIA_1 0x420028 /* BTE interrupt address 1 */ |
| |
| /* |
| * More miscellaneous registers |
| */ |
| #define IIO_IPCR 0x430000 /* Performance Control */ |
| #define IIO_IPPR 0x430008 /* Performance Profiling */ |
| |
| /* |
| * IO Error Clear register bit field definitions |
| */ |
| #define IECLR_BTE1 (1 << 18) /* clear bte error 1 ??? */ |
| #define IECLR_BTE0 (1 << 17) /* clear bte error 0 ??? */ |
| #define IECLR_CRAZY (1 << 16) /* clear crazy bit in wstat reg */ |
| #define IECLR_PRB_F (1 << 15) /* clear err bit in PRB_F reg */ |
| #define IECLR_PRB_E (1 << 14) /* clear err bit in PRB_E reg */ |
| #define IECLR_PRB_D (1 << 13) /* clear err bit in PRB_D reg */ |
| #define IECLR_PRB_C (1 << 12) /* clear err bit in PRB_C reg */ |
| #define IECLR_PRB_B (1 << 11) /* clear err bit in PRB_B reg */ |
| #define IECLR_PRB_A (1 << 10) /* clear err bit in PRB_A reg */ |
| #define IECLR_PRB_9 (1 << 9) /* clear err bit in PRB_9 reg */ |
| #define IECLR_PRB_8 (1 << 8) /* clear err bit in PRB_8 reg */ |
| #define IECLR_PRB_0 (1 << 0) /* clear err bit in PRB_0 reg */ |
| |
| /* |
| * IO PIO Read Table Entry format |
| */ |
| |
| #ifndef __ASSEMBLY__ |
| |
| typedef union iprte_a { |
| u64 entry; |
| struct { |
| u64 rsvd1 : 7, /* Reserved field */ |
| valid : 1, /* Maps to a timeout entry */ |
| rsvd2 : 1, |
| srcnode : 9, /* Node which did this PIO */ |
| initiator : 2, /* If T5A or T5B or IO */ |
| rsvd3 : 3, |
| addr : 38, /* Physical address of PIO */ |
| rsvd4 : 3; |
| } iprte_fields; |
| } iprte_a_t; |
| |
| #define iprte_valid iprte_fields.valid |
| #define iprte_timeout iprte_fields.timeout |
| #define iprte_srcnode iprte_fields.srcnode |
| #define iprte_init iprte_fields.initiator |
| #define iprte_addr iprte_fields.addr |
| |
| #endif /* !__ASSEMBLY__ */ |
| |
| #define IPRTE_ADDRSHFT 3 |
| |
| /* |
| * Hub IIO PRB Register format. |
| */ |
| |
| #ifndef __ASSEMBLY__ |
| /* |
| * Note: Fields bnakctr, anakctr, xtalkctrmode, ovflow fields are |
| * "Status" fields, and should only be used in case of clean up after errors. |
| */ |
| |
| typedef union iprb_u { |
| u64 reg_value; |
| struct { |
| u64 rsvd1: 15, |
| error: 1, /* Widget rcvd wr resp pkt w/ error */ |
| ovflow: 5, /* Over flow count. perf measurement */ |
| fire_and_forget: 1, /* Launch Write without response */ |
| mode: 2, /* Widget operation Mode */ |
| rsvd2: 2, |
| bnakctr: 14, |
| rsvd3: 2, |
| anakctr: 14, |
| xtalkctr: 8; |
| } iprb_fields_s; |
| } iprb_t; |
| |
| #define iprb_regval reg_value |
| |
| #define iprb_error iprb_fields_s.error |
| #define iprb_ovflow iprb_fields_s.ovflow |
| #define iprb_ff iprb_fields_s.fire_and_forget |
| #define iprb_mode iprb_fields_s.mode |
| #define iprb_bnakctr iprb_fields_s.bnakctr |
| #define iprb_anakctr iprb_fields_s.anakctr |
| #define iprb_xtalkctr iprb_fields_s.xtalkctr |
| |
| #endif /* !__ASSEMBLY__ */ |
| |
| /* |
| * values for mode field in iprb_t. |
| * For details of the meanings of NAK and Accept, refer the PIO flow |
| * document |
| */ |
| #define IPRB_MODE_NORMAL (0) |
| #define IPRB_MODE_COLLECT_A (1) /* PRB in collect A mode */ |
| #define IPRB_MODE_SERVICE_A (2) /* NAK B and Accept A */ |
| #define IPRB_MODE_SERVICE_B (3) /* NAK A and Accept B */ |
| |
| /* |
| * IO CRB entry C_A to E_A : Partial (cache) CRBS |
| */ |
| #ifndef __ASSEMBLY__ |
| typedef union icrbp_a { |
| u64 ip_reg; /* the entire register value */ |
| struct { |
| u64 error: 1, /* 63, error occurred */ |
| ln_uce: 1, /* 62: uncorrectable memory */ |
| ln_ae: 1, /* 61: protection violation */ |
| ln_werr:1, /* 60: write access error */ |
| ln_aerr:1, /* 59: sn0net: Address error */ |
| ln_perr:1, /* 58: sn0net: poison error */ |
| timeout:1, /* 57: CRB timed out */ |
| l_bdpkt:1, /* 56: truncated pkt on sn0net */ |
| c_bdpkt:1, /* 55: truncated pkt on xtalk */ |
| c_err: 1, /* 54: incoming xtalk req, err set*/ |
| rsvd1: 12, /* 53-42: reserved */ |
| valid: 1, /* 41: Valid status */ |
| sidn: 4, /* 40-37: SIDN field of xtalk rqst */ |
| tnum: 5, /* 36-32: TNUM of xtalk request */ |
| bo: 1, /* 31: barrier op set in xtalk rqst*/ |
| resprqd:1, /* 30: xtalk rqst requires response*/ |
| gbr: 1, /* 29: gbr bit set in xtalk rqst */ |
| size: 2, /* 28-27: size of xtalk request */ |
| excl: 4, /* 26-23: exclusive bit(s) */ |
| stall: 3, /* 22-20: stall (xtalk, bte 0/1) */ |
| intvn: 1, /* 19: rqst target of intervention*/ |
| resp: 1, /* 18: Data response given to t5 */ |
| ack: 1, /* 17: Data ack received. */ |
| hold: 1, /* 16: crb gathering invalidate acks*/ |
| wb: 1, /* 15: writeback pending. */ |
| ack_cnt:11, /* 14-04: counter of invalidate acks*/ |
| tscaler:4; /* 03-00: Timeout prescaler */ |
| } ip_fmt; |
| } icrbp_a_t; |
| |
| #endif /* !__ASSEMBLY__ */ |
| |
| /* |
| * A couple of defines to go with the above structure. |
| */ |
| #define ICRBP_A_CERR_SHFT 54 |
| #define ICRBP_A_ERR_MASK 0x3ff |
| |
| #ifndef __ASSEMBLY__ |
| typedef union hubii_idsr { |
| u64 iin_reg; |
| struct { |
| u64 rsvd1 : 35, |
| isent : 1, |
| rsvd2 : 3, |
| ienable: 1, |
| rsvd : 7, |
| node : 9, |
| rsvd4 : 1, |
| level : 7; |
| } iin_fmt; |
| } hubii_idsr_t; |
| #endif /* !__ASSEMBLY__ */ |
| |
| /* |
| * IO BTE Length/Status (IIO_IBLS) register bit field definitions |
| */ |
| #define IBLS_BUSY (0x1 << 20) |
| #define IBLS_ERROR_SHFT 16 |
| #define IBLS_ERROR (0x1 << IBLS_ERROR_SHFT) |
| #define IBLS_LENGTH_MASK 0xffff |
| |
| /* |
| * IO BTE Control/Terminate register (IBCT) register bit field definitions |
| */ |
| #define IBCT_POISON (0x1 << 8) |
| #define IBCT_NOTIFY (0x1 << 4) |
| #define IBCT_ZFIL_MODE (0x1 << 0) |
| |
| /* |
| * IO BTE Interrupt Address Register (IBIA) register bit field definitions |
| */ |
| #define IBIA_LEVEL_SHFT 16 |
| #define IBIA_LEVEL_MASK (0x7f << IBIA_LEVEL_SHFT) |
| #define IBIA_NODE_ID_SHFT 0 |
| #define IBIA_NODE_ID_MASK (0x1ff) |
| |
| /* |
| * Miscellaneous hub constants |
| */ |
| |
| /* Number of widgets supported by hub */ |
| #define HUB_NUM_WIDGET 9 |
| #define HUB_WIDGET_ID_MIN 0x8 |
| #define HUB_WIDGET_ID_MAX 0xf |
| |
| #define HUB_WIDGET_PART_NUM 0xc101 |
| #define MAX_HUBS_PER_XBOW 2 |
| |
| /* |
| * Get a hub's widget id from widget control register |
| */ |
| #define IIO_WCR_WID_GET(nasid) (REMOTE_HUB_L(nasid, III_WCR) & 0xf) |
| #define IIO_WST_ERROR_MASK (UINT64_CAST 1 << 32) /* Widget status error */ |
| |
| /* |
| * Number of credits Hub widget has while sending req/response to |
| * xbow. |
| * Value of 3 is required by Xbow 1.1 |
| * We may be able to increase this to 4 with Xbow 1.2. |
| */ |
| #define HUBII_XBOW_CREDIT 3 |
| #define HUBII_XBOW_REV2_CREDIT 4 |
| |
| #endif /* _ASM_SGI_SN_SN0_HUBIO_H */ |