| /* |
| * MPC8569E MDS Device Tree Source |
| * |
| * Copyright (C) 2009 Freescale Semiconductor Inc. |
| * |
| * This program is free software; you can redistribute it and/or modify it |
| * under the terms of the GNU General Public License as published by the |
| * Free Software Foundation; either version 2 of the License, or (at your |
| * option) any later version. |
| */ |
| |
| /dts-v1/; |
| |
| / { |
| model = "MPC8569EMDS"; |
| compatible = "fsl,MPC8569EMDS"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| aliases { |
| serial0 = &serial0; |
| serial1 = &serial1; |
| ethernet0 = &enet0; |
| ethernet1 = &enet1; |
| ethernet2 = &enet2; |
| ethernet3 = &enet3; |
| ethernet5 = &enet5; |
| ethernet7 = &enet7; |
| pci1 = &pci1; |
| rapidio0 = &rio0; |
| }; |
| |
| cpus { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| PowerPC,8569@0 { |
| device_type = "cpu"; |
| reg = <0x0>; |
| d-cache-line-size = <32>; // 32 bytes |
| i-cache-line-size = <32>; // 32 bytes |
| d-cache-size = <0x8000>; // L1, 32K |
| i-cache-size = <0x8000>; // L1, 32K |
| timebase-frequency = <0>; |
| bus-frequency = <0>; |
| clock-frequency = <0>; |
| next-level-cache = <&L2>; |
| }; |
| }; |
| |
| memory { |
| device_type = "memory"; |
| }; |
| |
| localbus@e0005000 { |
| #address-cells = <2>; |
| #size-cells = <1>; |
| compatible = "fsl,mpc8569-elbc", "fsl,elbc", "simple-bus"; |
| reg = <0xe0005000 0x1000>; |
| interrupts = <19 2>; |
| interrupt-parent = <&mpic>; |
| |
| ranges = <0x0 0x0 0xfe000000 0x02000000 |
| 0x1 0x0 0xf8000000 0x00008000 |
| 0x2 0x0 0xf0000000 0x04000000 |
| 0x3 0x0 0xfc000000 0x00008000 |
| 0x4 0x0 0xf8008000 0x00008000 |
| 0x5 0x0 0xf8010000 0x00008000>; |
| |
| nor@0,0 { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| compatible = "cfi-flash"; |
| reg = <0x0 0x0 0x02000000>; |
| bank-width = <1>; |
| device-width = <1>; |
| partition@0 { |
| label = "ramdisk"; |
| reg = <0x00000000 0x01c00000>; |
| }; |
| partition@1c00000 { |
| label = "kernel"; |
| reg = <0x01c00000 0x002e0000>; |
| }; |
| partiton@1ee0000 { |
| label = "dtb"; |
| reg = <0x01ee0000 0x00020000>; |
| }; |
| partition@1f00000 { |
| label = "firmware"; |
| reg = <0x01f00000 0x00080000>; |
| read-only; |
| }; |
| partition@1f80000 { |
| label = "u-boot"; |
| reg = <0x01f80000 0x00080000>; |
| read-only; |
| }; |
| }; |
| |
| bcsr@1,0 { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| compatible = "fsl,mpc8569mds-bcsr"; |
| reg = <1 0 0x8000>; |
| ranges = <0 1 0 0x8000>; |
| |
| bcsr17: gpio-controller@11 { |
| #gpio-cells = <2>; |
| compatible = "fsl,mpc8569mds-bcsr-gpio"; |
| reg = <0x11 0x1>; |
| gpio-controller; |
| }; |
| }; |
| |
| nand@3,0 { |
| compatible = "fsl,mpc8569-fcm-nand", |
| "fsl,elbc-fcm-nand"; |
| reg = <3 0 0x8000>; |
| }; |
| |
| pib@4,0 { |
| compatible = "fsl,mpc8569mds-pib"; |
| reg = <4 0 0x8000>; |
| }; |
| |
| pib@5,0 { |
| compatible = "fsl,mpc8569mds-pib"; |
| reg = <5 0 0x8000>; |
| }; |
| }; |
| |
| soc@e0000000 { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| device_type = "soc"; |
| compatible = "fsl,mpc8569-immr", "simple-bus"; |
| ranges = <0x0 0xe0000000 0x100000>; |
| bus-frequency = <0>; |
| |
| ecm-law@0 { |
| compatible = "fsl,ecm-law"; |
| reg = <0x0 0x1000>; |
| fsl,num-laws = <10>; |
| }; |
| |
| ecm@1000 { |
| compatible = "fsl,mpc8569-ecm", "fsl,ecm"; |
| reg = <0x1000 0x1000>; |
| interrupts = <17 2>; |
| interrupt-parent = <&mpic>; |
| }; |
| |
| memory-controller@2000 { |
| compatible = "fsl,mpc8569-memory-controller"; |
| reg = <0x2000 0x1000>; |
| interrupt-parent = <&mpic>; |
| interrupts = <18 2>; |
| }; |
| |
| i2c@3000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| cell-index = <0>; |
| compatible = "fsl-i2c"; |
| reg = <0x3000 0x100>; |
| interrupts = <43 2>; |
| interrupt-parent = <&mpic>; |
| dfsrr; |
| |
| rtc@68 { |
| compatible = "dallas,ds1374"; |
| reg = <0x68>; |
| }; |
| }; |
| |
| i2c@3100 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| cell-index = <1>; |
| compatible = "fsl-i2c"; |
| reg = <0x3100 0x100>; |
| interrupts = <43 2>; |
| interrupt-parent = <&mpic>; |
| dfsrr; |
| }; |
| |
| serial0: serial@4500 { |
| cell-index = <0>; |
| device_type = "serial"; |
| compatible = "ns16550"; |
| reg = <0x4500 0x100>; |
| clock-frequency = <0>; |
| interrupts = <42 2>; |
| interrupt-parent = <&mpic>; |
| }; |
| |
| serial1: serial@4600 { |
| cell-index = <1>; |
| device_type = "serial"; |
| compatible = "ns16550"; |
| reg = <0x4600 0x100>; |
| clock-frequency = <0>; |
| interrupts = <42 2>; |
| interrupt-parent = <&mpic>; |
| }; |
| |
| L2: l2-cache-controller@20000 { |
| compatible = "fsl,mpc8569-l2-cache-controller"; |
| reg = <0x20000 0x1000>; |
| cache-line-size = <32>; // 32 bytes |
| cache-size = <0x80000>; // L2, 512K |
| interrupt-parent = <&mpic>; |
| interrupts = <16 2>; |
| }; |
| |
| dma@21300 { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| compatible = "fsl,mpc8569-dma", "fsl,eloplus-dma"; |
| reg = <0x21300 0x4>; |
| ranges = <0x0 0x21100 0x200>; |
| cell-index = <0>; |
| dma-channel@0 { |
| compatible = "fsl,mpc8569-dma-channel", |
| "fsl,eloplus-dma-channel"; |
| reg = <0x0 0x80>; |
| cell-index = <0>; |
| interrupt-parent = <&mpic>; |
| interrupts = <20 2>; |
| }; |
| dma-channel@80 { |
| compatible = "fsl,mpc8569-dma-channel", |
| "fsl,eloplus-dma-channel"; |
| reg = <0x80 0x80>; |
| cell-index = <1>; |
| interrupt-parent = <&mpic>; |
| interrupts = <21 2>; |
| }; |
| dma-channel@100 { |
| compatible = "fsl,mpc8569-dma-channel", |
| "fsl,eloplus-dma-channel"; |
| reg = <0x100 0x80>; |
| cell-index = <2>; |
| interrupt-parent = <&mpic>; |
| interrupts = <22 2>; |
| }; |
| dma-channel@180 { |
| compatible = "fsl,mpc8569-dma-channel", |
| "fsl,eloplus-dma-channel"; |
| reg = <0x180 0x80>; |
| cell-index = <3>; |
| interrupt-parent = <&mpic>; |
| interrupts = <23 2>; |
| }; |
| }; |
| |
| sdhci@2e000 { |
| compatible = "fsl,mpc8569-esdhc", "fsl,esdhc"; |
| reg = <0x2e000 0x1000>; |
| interrupts = <72 0x8>; |
| interrupt-parent = <&mpic>; |
| /* Filled in by U-Boot */ |
| clock-frequency = <0>; |
| status = "disabled"; |
| sdhci,1-bit-only; |
| }; |
| |
| crypto@30000 { |
| compatible = "fsl,sec3.1", "fsl,sec3.0", "fsl,sec2.4", |
| "fsl,sec2.2", "fsl,sec2.1", "fsl,sec2.0"; |
| reg = <0x30000 0x10000>; |
| interrupts = <45 2 58 2>; |
| interrupt-parent = <&mpic>; |
| fsl,num-channels = <4>; |
| fsl,channel-fifo-len = <24>; |
| fsl,exec-units-mask = <0xbfe>; |
| fsl,descriptor-types-mask = <0x3ab0ebf>; |
| }; |
| |
| mpic: pic@40000 { |
| interrupt-controller; |
| #address-cells = <0>; |
| #interrupt-cells = <2>; |
| reg = <0x40000 0x40000>; |
| compatible = "chrp,open-pic"; |
| device_type = "open-pic"; |
| }; |
| |
| msi@41600 { |
| compatible = "fsl,mpc8568-msi", "fsl,mpic-msi"; |
| reg = <0x41600 0x80>; |
| msi-available-ranges = <0 0x100>; |
| interrupts = < |
| 0xe0 0 |
| 0xe1 0 |
| 0xe2 0 |
| 0xe3 0 |
| 0xe4 0 |
| 0xe5 0 |
| 0xe6 0 |
| 0xe7 0>; |
| interrupt-parent = <&mpic>; |
| }; |
| |
| global-utilities@e0000 { |
| compatible = "fsl,mpc8569-guts"; |
| reg = <0xe0000 0x1000>; |
| fsl,has-rstcr; |
| }; |
| |
| par_io@e0100 { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| reg = <0xe0100 0x100>; |
| ranges = <0x0 0xe0100 0x100>; |
| device_type = "par_io"; |
| num-ports = <7>; |
| |
| qe_pio_e: gpio-controller@80 { |
| #gpio-cells = <2>; |
| compatible = "fsl,mpc8569-qe-pario-bank", |
| "fsl,mpc8323-qe-pario-bank"; |
| reg = <0x80 0x18>; |
| gpio-controller; |
| }; |
| |
| qe_pio_f: gpio-controller@a0 { |
| #gpio-cells = <2>; |
| compatible = "fsl,mpc8569-qe-pario-bank", |
| "fsl,mpc8323-qe-pario-bank"; |
| reg = <0xa0 0x18>; |
| gpio-controller; |
| }; |
| |
| pio1: ucc_pin@01 { |
| pio-map = < |
| /* port pin dir open_drain assignment has_irq */ |
| 0x2 0x1f 0x1 0x0 0x1 0x0 /* QE_MUX_MDC */ |
| 0x2 0x1e 0x3 0x0 0x2 0x0 /* QE_MUX_MDIO */ |
| 0x2 0x0b 0x2 0x0 0x1 0x0 /* CLK12*/ |
| 0x0 0x0 0x1 0x0 0x3 0x0 /* ENET1_TXD0_SER1_TXD0 */ |
| 0x0 0x1 0x1 0x0 0x3 0x0 /* ENET1_TXD1_SER1_TXD1 */ |
| 0x0 0x2 0x1 0x0 0x1 0x0 /* ENET1_TXD2_SER1_TXD2 */ |
| 0x0 0x3 0x1 0x0 0x2 0x0 /* ENET1_TXD3_SER1_TXD3 */ |
| 0x0 0x6 0x2 0x0 0x3 0x0 /* ENET1_RXD0_SER1_RXD0 */ |
| 0x0 0x7 0x2 0x0 0x1 0x0 /* ENET1_RXD1_SER1_RXD1 */ |
| 0x0 0x8 0x2 0x0 0x2 0x0 /* ENET1_RXD2_SER1_RXD2 */ |
| 0x0 0x9 0x2 0x0 0x2 0x0 /* ENET1_RXD3_SER1_RXD3 */ |
| 0x0 0x4 0x1 0x0 0x2 0x0 /* ENET1_TX_EN_SER1_RTS_B */ |
| 0x0 0xc 0x2 0x0 0x3 0x0 /* ENET1_RX_DV_SER1_CTS_B */ |
| 0x2 0x8 0x2 0x0 0x1 0x0 /* ENET1_GRXCLK */ |
| 0x2 0x14 0x1 0x0 0x2 0x0>; /* ENET1_GTXCLK */ |
| }; |
| |
| pio2: ucc_pin@02 { |
| pio-map = < |
| /* port pin dir open_drain assignment has_irq */ |
| 0x2 0x1f 0x1 0x0 0x1 0x0 /* QE_MUX_MDC */ |
| 0x2 0x1e 0x3 0x0 0x2 0x0 /* QE_MUX_MDIO */ |
| 0x2 0x10 0x2 0x0 0x3 0x0 /* CLK17 */ |
| 0x0 0xe 0x1 0x0 0x2 0x0 /* ENET2_TXD0_SER2_TXD0 */ |
| 0x0 0xf 0x1 0x0 0x2 0x0 /* ENET2_TXD1_SER2_TXD1 */ |
| 0x0 0x10 0x1 0x0 0x1 0x0 /* ENET2_TXD2_SER2_TXD2 */ |
| 0x0 0x11 0x1 0x0 0x1 0x0 /* ENET2_TXD3_SER2_TXD3 */ |
| 0x0 0x14 0x2 0x0 0x2 0x0 /* ENET2_RXD0_SER2_RXD0 */ |
| 0x0 0x15 0x2 0x0 0x1 0x0 /* ENET2_RXD1_SER2_RXD1 */ |
| 0x0 0x16 0x2 0x0 0x1 0x0 /* ENET2_RXD2_SER2_RXD2 */ |
| 0x0 0x17 0x2 0x0 0x1 0x0 /* ENET2_RXD3_SER2_RXD3 */ |
| 0x0 0x12 0x1 0x0 0x2 0x0 /* ENET2_TX_EN_SER2_RTS_B */ |
| 0x0 0x1a 0x2 0x0 0x3 0x0 /* ENET2_RX_DV_SER2_CTS_B */ |
| 0x2 0x3 0x2 0x0 0x1 0x0 /* ENET2_GRXCLK */ |
| 0x2 0x2 0x1 0x0 0x2 0x0>; /* ENET2_GTXCLK */ |
| }; |
| |
| pio3: ucc_pin@03 { |
| pio-map = < |
| /* port pin dir open_drain assignment has_irq */ |
| 0x2 0x1f 0x1 0x0 0x1 0x0 /* QE_MUX_MDC */ |
| 0x2 0x1e 0x3 0x0 0x2 0x0 /* QE_MUX_MDIO */ |
| 0x2 0x0b 0x2 0x0 0x1 0x0 /* CLK12*/ |
| 0x0 0x1d 0x1 0x0 0x2 0x0 /* ENET3_TXD0_SER3_TXD0 */ |
| 0x0 0x1e 0x1 0x0 0x3 0x0 /* ENET3_TXD1_SER3_TXD1 */ |
| 0x0 0x1f 0x1 0x0 0x2 0x0 /* ENET3_TXD2_SER3_TXD2 */ |
| 0x1 0x0 0x1 0x0 0x3 0x0 /* ENET3_TXD3_SER3_TXD3 */ |
| 0x1 0x3 0x2 0x0 0x3 0x0 /* ENET3_RXD0_SER3_RXD0 */ |
| 0x1 0x4 0x2 0x0 0x1 0x0 /* ENET3_RXD1_SER3_RXD1 */ |
| 0x1 0x5 0x2 0x0 0x2 0x0 /* ENET3_RXD2_SER3_RXD2 */ |
| 0x1 0x6 0x2 0x0 0x3 0x0 /* ENET3_RXD3_SER3_RXD3 */ |
| 0x1 0x1 0x1 0x0 0x1 0x0 /* ENET3_TX_EN_SER3_RTS_B */ |
| 0x1 0x9 0x2 0x0 0x3 0x0 /* ENET3_RX_DV_SER3_CTS_B */ |
| 0x2 0x9 0x2 0x0 0x2 0x0 /* ENET3_GRXCLK */ |
| 0x2 0x19 0x1 0x0 0x2 0x0>; /* ENET3_GTXCLK */ |
| }; |
| |
| pio4: ucc_pin@04 { |
| pio-map = < |
| /* port pin dir open_drain assignment has_irq */ |
| 0x2 0x1f 0x1 0x0 0x1 0x0 /* QE_MUX_MDC */ |
| 0x2 0x1e 0x3 0x0 0x2 0x0 /* QE_MUX_MDIO */ |
| 0x2 0x10 0x2 0x0 0x3 0x0 /* CLK17 */ |
| 0x1 0xc 0x1 0x0 0x2 0x0 /* ENET4_TXD0_SER4_TXD0 */ |
| 0x1 0xd 0x1 0x0 0x2 0x0 /* ENET4_TXD1_SER4_TXD1 */ |
| 0x1 0xe 0x1 0x0 0x1 0x0 /* ENET4_TXD2_SER4_TXD2 */ |
| 0x1 0xf 0x1 0x0 0x2 0x0 /* ENET4_TXD3_SER4_TXD3 */ |
| 0x1 0x12 0x2 0x0 0x2 0x0 /* ENET4_RXD0_SER4_RXD0 */ |
| 0x1 0x13 0x2 0x0 0x1 0x0 /* ENET4_RXD1_SER4_RXD1 */ |
| 0x1 0x14 0x2 0x0 0x1 0x0 /* ENET4_RXD2_SER4_RXD2 */ |
| 0x1 0x15 0x2 0x0 0x2 0x0 /* ENET4_RXD3_SER4_RXD3 */ |
| 0x1 0x10 0x1 0x0 0x2 0x0 /* ENET4_TX_EN_SER4_RTS_B */ |
| 0x1 0x18 0x2 0x0 0x3 0x0 /* ENET4_RX_DV_SER4_CTS_B */ |
| 0x2 0x11 0x2 0x0 0x2 0x0 /* ENET4_GRXCLK */ |
| 0x2 0x18 0x1 0x0 0x2 0x0>; /* ENET4_GTXCLK */ |
| }; |
| }; |
| }; |
| |
| qe@e0080000 { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| device_type = "qe"; |
| compatible = "fsl,qe"; |
| ranges = <0x0 0xe0080000 0x40000>; |
| reg = <0xe0080000 0x480>; |
| brg-frequency = <0>; |
| bus-frequency = <0>; |
| fsl,qe-num-riscs = <4>; |
| fsl,qe-num-snums = <46>; |
| |
| qeic: interrupt-controller@80 { |
| interrupt-controller; |
| compatible = "fsl,qe-ic"; |
| #address-cells = <0>; |
| #interrupt-cells = <1>; |
| reg = <0x80 0x80>; |
| interrupts = <46 2 46 2>; //high:30 low:30 |
| interrupt-parent = <&mpic>; |
| }; |
| |
| timer@440 { |
| compatible = "fsl,mpc8569-qe-gtm", |
| "fsl,qe-gtm", "fsl,gtm"; |
| reg = <0x440 0x40>; |
| interrupts = <12 13 14 15>; |
| interrupt-parent = <&qeic>; |
| /* Filled in by U-Boot */ |
| clock-frequency = <0>; |
| }; |
| |
| spi@4c0 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,mpc8569-qe-spi", "fsl,spi"; |
| reg = <0x4c0 0x40>; |
| cell-index = <0>; |
| interrupts = <2>; |
| interrupt-parent = <&qeic>; |
| gpios = <&qe_pio_e 30 0>; |
| mode = "cpu-qe"; |
| |
| serial-flash@0 { |
| compatible = "stm,m25p40"; |
| reg = <0>; |
| spi-max-frequency = <25000000>; |
| }; |
| }; |
| |
| spi@500 { |
| cell-index = <1>; |
| compatible = "fsl,spi"; |
| reg = <0x500 0x40>; |
| interrupts = <1>; |
| interrupt-parent = <&qeic>; |
| mode = "cpu"; |
| }; |
| |
| usb@6c0 { |
| compatible = "fsl,mpc8569-qe-usb", |
| "fsl,mpc8323-qe-usb"; |
| reg = <0x6c0 0x40 0x8b00 0x100>; |
| interrupts = <11>; |
| interrupt-parent = <&qeic>; |
| fsl,fullspeed-clock = "clk5"; |
| fsl,lowspeed-clock = "brg10"; |
| gpios = <&qe_pio_f 3 0 /* USBOE */ |
| &qe_pio_f 4 0 /* USBTP */ |
| &qe_pio_f 5 0 /* USBTN */ |
| &qe_pio_f 6 0 /* USBRP */ |
| &qe_pio_f 8 0 /* USBRN */ |
| &bcsr17 6 0 /* SPEED */ |
| &bcsr17 5 1>; /* POWER */ |
| }; |
| |
| enet0: ucc@2000 { |
| device_type = "network"; |
| compatible = "ucc_geth"; |
| cell-index = <1>; |
| reg = <0x2000 0x200>; |
| interrupts = <32>; |
| interrupt-parent = <&qeic>; |
| local-mac-address = [ 00 00 00 00 00 00 ]; |
| rx-clock-name = "none"; |
| tx-clock-name = "clk12"; |
| pio-handle = <&pio1>; |
| phy-handle = <&qe_phy0>; |
| phy-connection-type = "rgmii-id"; |
| }; |
| |
| mdio@2120 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x2120 0x18>; |
| compatible = "fsl,ucc-mdio"; |
| |
| qe_phy0: ethernet-phy@07 { |
| interrupt-parent = <&mpic>; |
| interrupts = <1 1>; |
| reg = <0x7>; |
| device_type = "ethernet-phy"; |
| }; |
| qe_phy1: ethernet-phy@01 { |
| interrupt-parent = <&mpic>; |
| interrupts = <2 1>; |
| reg = <0x1>; |
| device_type = "ethernet-phy"; |
| }; |
| qe_phy2: ethernet-phy@02 { |
| interrupt-parent = <&mpic>; |
| interrupts = <3 1>; |
| reg = <0x2>; |
| device_type = "ethernet-phy"; |
| }; |
| qe_phy3: ethernet-phy@03 { |
| interrupt-parent = <&mpic>; |
| interrupts = <4 1>; |
| reg = <0x3>; |
| device_type = "ethernet-phy"; |
| }; |
| qe_phy5: ethernet-phy@04 { |
| interrupt-parent = <&mpic>; |
| reg = <0x04>; |
| device_type = "ethernet-phy"; |
| }; |
| qe_phy7: ethernet-phy@06 { |
| interrupt-parent = <&mpic>; |
| reg = <0x6>; |
| device_type = "ethernet-phy"; |
| }; |
| tbi-phy@11 { |
| reg = <0x11>; |
| device_type = "tbi-phy"; |
| }; |
| }; |
| mdio@3520 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x3520 0x18>; |
| compatible = "fsl,ucc-mdio"; |
| |
| tbi0: tbi-phy@15 { |
| reg = <0x15>; |
| device_type = "tbi-phy"; |
| }; |
| }; |
| mdio@3720 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x3720 0x38>; |
| compatible = "fsl,ucc-mdio"; |
| tbi1: tbi-phy@17 { |
| reg = <0x17>; |
| device_type = "tbi-phy"; |
| }; |
| }; |
| |
| enet2: ucc@2200 { |
| device_type = "network"; |
| compatible = "ucc_geth"; |
| cell-index = <3>; |
| reg = <0x2200 0x200>; |
| interrupts = <34>; |
| interrupt-parent = <&qeic>; |
| local-mac-address = [ 00 00 00 00 00 00 ]; |
| rx-clock-name = "none"; |
| tx-clock-name = "clk12"; |
| pio-handle = <&pio3>; |
| phy-handle = <&qe_phy2>; |
| phy-connection-type = "rgmii-id"; |
| }; |
| |
| enet1: ucc@3000 { |
| device_type = "network"; |
| compatible = "ucc_geth"; |
| cell-index = <2>; |
| reg = <0x3000 0x200>; |
| interrupts = <33>; |
| interrupt-parent = <&qeic>; |
| local-mac-address = [ 00 00 00 00 00 00 ]; |
| rx-clock-name = "none"; |
| tx-clock-name = "clk17"; |
| pio-handle = <&pio2>; |
| phy-handle = <&qe_phy1>; |
| phy-connection-type = "rgmii-id"; |
| }; |
| |
| enet3: ucc@3200 { |
| device_type = "network"; |
| compatible = "ucc_geth"; |
| cell-index = <4>; |
| reg = <0x3200 0x200>; |
| interrupts = <35>; |
| interrupt-parent = <&qeic>; |
| local-mac-address = [ 00 00 00 00 00 00 ]; |
| rx-clock-name = "none"; |
| tx-clock-name = "clk17"; |
| pio-handle = <&pio4>; |
| phy-handle = <&qe_phy3>; |
| phy-connection-type = "rgmii-id"; |
| }; |
| |
| enet5: ucc@3400 { |
| device_type = "network"; |
| compatible = "ucc_geth"; |
| cell-index = <6>; |
| reg = <0x3400 0x200>; |
| interrupts = <41>; |
| interrupt-parent = <&qeic>; |
| local-mac-address = [ 00 00 00 00 00 00 ]; |
| rx-clock-name = "none"; |
| tx-clock-name = "none"; |
| tbi-handle = <&tbi0>; |
| phy-handle = <&qe_phy5>; |
| phy-connection-type = "sgmii"; |
| }; |
| |
| enet7: ucc@3600 { |
| device_type = "network"; |
| compatible = "ucc_geth"; |
| cell-index = <8>; |
| reg = <0x3600 0x200>; |
| interrupts = <43>; |
| interrupt-parent = <&qeic>; |
| local-mac-address = [ 00 00 00 00 00 00 ]; |
| rx-clock-name = "none"; |
| tx-clock-name = "none"; |
| tbi-handle = <&tbi1>; |
| phy-handle = <&qe_phy7>; |
| phy-connection-type = "sgmii"; |
| }; |
| |
| muram@10000 { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| compatible = "fsl,qe-muram", "fsl,cpm-muram"; |
| ranges = <0x0 0x10000 0x20000>; |
| |
| data-only@0 { |
| compatible = "fsl,qe-muram-data", |
| "fsl,cpm-muram-data"; |
| reg = <0x0 0x20000>; |
| }; |
| }; |
| |
| }; |
| |
| /* PCI Express */ |
| pci1: pcie@e000a000 { |
| compatible = "fsl,mpc8548-pcie"; |
| device_type = "pci"; |
| #interrupt-cells = <1>; |
| #size-cells = <2>; |
| #address-cells = <3>; |
| reg = <0xe000a000 0x1000>; |
| interrupt-map-mask = <0xf800 0x0 0x0 0x7>; |
| interrupt-map = < |
| /* IDSEL 0x0 (PEX) */ |
| 00000 0x0 0x0 0x1 &mpic 0x0 0x1 |
| 00000 0x0 0x0 0x2 &mpic 0x1 0x1 |
| 00000 0x0 0x0 0x3 &mpic 0x2 0x1 |
| 00000 0x0 0x0 0x4 &mpic 0x3 0x1>; |
| |
| interrupt-parent = <&mpic>; |
| interrupts = <26 2>; |
| bus-range = <0 255>; |
| ranges = <0x2000000 0x0 0xa0000000 0xa0000000 0x0 0x10000000 |
| 0x1000000 0x0 0x00000000 0xe2800000 0x0 0x00800000>; |
| clock-frequency = <33333333>; |
| pcie@0 { |
| reg = <0x0 0x0 0x0 0x0 0x0>; |
| #size-cells = <2>; |
| #address-cells = <3>; |
| device_type = "pci"; |
| ranges = <0x2000000 0x0 0xa0000000 |
| 0x2000000 0x0 0xa0000000 |
| 0x0 0x10000000 |
| |
| 0x1000000 0x0 0x0 |
| 0x1000000 0x0 0x0 |
| 0x0 0x800000>; |
| }; |
| }; |
| |
| rio0: rapidio@e00c00000 { |
| #address-cells = <2>; |
| #size-cells = <2>; |
| compatible = "fsl,mpc8569-rapidio", "fsl,rapidio-delta"; |
| reg = <0xe00c0000 0x20000>; |
| ranges = <0x0 0x0 0xc0000000 0x0 0x20000000>; |
| interrupts = <48 2 /* error */ |
| 49 2 /* bell_outb */ |
| 50 2 /* bell_inb */ |
| 53 2 /* msg1_tx */ |
| 54 2 /* msg1_rx */ |
| 55 2 /* msg2_tx */ |
| 56 2 /* msg2_rx */>; |
| interrupt-parent = <&mpic>; |
| }; |
| }; |