drivers/net/wireless/Kconfig - LeafOS-Devices/android_kernel_samsung_gta4xl - Gitiles

 #
 # Wireless LAN device configuration
 #

 menu "Wireless LAN"
 	depends on !S390

 config WLAN_PRE80211
 	bool "Wireless LAN (pre-802.11)"
 	depends on NETDEVICES
 	---help---
 	  Say Y if you have any pre-802.11 wireless LAN hardware.

 	  This option does not affect the kernel build, it only
 	  lets you choose drivers.

 config STRIP
 	tristate "STRIP (Metricom starmode radio IP)"
 	depends on INET && WLAN_PRE80211
 	select WIRELESS_EXT
 	---help---
 	  Say Y if you have a Metricom radio and intend to use Starmode Radio
 	  IP. STRIP is a radio protocol developed for the MosquitoNet project
 	  (on the WWW at <http://mosquitonet.stanford.edu/>) to send Internet
 	  traffic using Metricom radios.  Metricom radios are small, battery
 	  powered, 100kbit/sec packet radio transceivers, about the size and
 	  weight of a cellular telephone. (You may also have heard them called
 	  "Metricom modems" but we avoid the term "modem" because it misleads
 	  many people into thinking that you can plug a Metricom modem into a
 	  phone line and use it as a modem.)

 	  You can use STRIP on any Linux machine with a serial port, although
 	  it is obviously most useful for people with laptop computers. If you
 	  think you might get a Metricom radio in the future, there is no harm
 	  in saying Y to STRIP now, except that it makes the kernel a bit
 	  bigger.

 	  To compile this as a module, choose M here: the module will be
 	  called strip.

 config ARLAN
 	tristate "Aironet Arlan 655 & IC2200 DS support"
 	depends on ISA && !64BIT && WLAN_PRE80211
 	select WIRELESS_EXT
 	---help---
 	  Aironet makes Arlan, a class of wireless LAN adapters. These use the
 	  www.Telxon.com chip, which is also used on several similar cards.
 	  This driver is tested on the 655 and IC2200 series cards. Look at
 	  <http://www.ylenurme.ee/~elmer/655/> for the latest information.

 	  The driver is built as two modules, arlan and arlan-proc. The latter
 	  is the /proc interface and is not needed most of time.

 	  On some computers the card ends up in non-valid state after some
 	  time. Use a ping-reset script to clear it.

 config WAVELAN
 	tristate "AT&T/Lucent old WaveLAN & DEC RoamAbout DS ISA support"
 	depends on ISA && WLAN_PRE80211
 	select WIRELESS_EXT
 	---help---
 	  The Lucent WaveLAN (formerly NCR and AT&T; or DEC RoamAbout DS) is
 	  a Radio LAN (wireless Ethernet-like Local Area Network) using the
 	  radio frequencies 900 MHz and 2.4 GHz.

 	  If you want to use an ISA WaveLAN card under Linux, say Y and read
 	  the Ethernet-HOWTO, available from
 	  <http://www.tldp.org/docs.html#howto>. Some more specific
 	  information is contained in
 	  <file:Documentation/networking/wavelan.txt> and in the source code
 	  <file:drivers/net/wavelan.p.h>.

 	  You will also need the wireless tools package available from
 	  <http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html>.
 	  Please read the man pages contained therein.

 	  To compile this driver as a module, choose M here: the module will be
 	  called wavelan.

 config PCMCIA_WAVELAN
 	tristate "AT&T/Lucent old WaveLAN Pcmcia wireless support"
 	depends on PCMCIA && WLAN_PRE80211
 	select WIRELESS_EXT
 	help
 	  Say Y here if you intend to attach an AT&T/Lucent Wavelan PCMCIA
 	  (PC-card) wireless Ethernet networking card to your computer.  This
 	  driver is for the non-IEEE-802.11 Wavelan cards.

 	  To compile this driver as a module, choose M here: the module will be
 	  called wavelan_cs.  If unsure, say N.

 config PCMCIA_NETWAVE
 	tristate "Xircom Netwave AirSurfer Pcmcia wireless support"
 	depends on PCMCIA && WLAN_PRE80211
 	select WIRELESS_EXT
 	help
 	  Say Y here if you intend to attach this type of PCMCIA (PC-card)
 	  wireless Ethernet networking card to your computer.

 	  To compile this driver as a module, choose M here: the module will be
 	  called netwave_cs.  If unsure, say N.


 config WLAN_80211
 	bool "Wireless LAN (IEEE 802.11)"
 	depends on NETDEVICES
 	---help---
 	  Say Y if you have any 802.11 wireless LAN hardware.

 	  This option does not affect the kernel build, it only
 	  lets you choose drivers.

 config PCMCIA_RAYCS
 	tristate "Aviator/Raytheon 2.4MHz wireless support"
 	depends on PCMCIA && WLAN_80211
 	select WIRELESS_EXT
 	---help---
 	  Say Y here if you intend to attach an Aviator/Raytheon PCMCIA
 	  (PC-card) wireless Ethernet networking card to your computer.
 	  Please read the file <file:Documentation/networking/ray_cs.txt> for
 	  details.

 	  To compile this driver as a module, choose M here: the module will be
 	  called ray_cs.  If unsure, say N.

 config IPW2100
 	tristate "Intel PRO/Wireless 2100 Network Connection"
 	depends on PCI && WLAN_80211
 	select WIRELESS_EXT
 	select FW_LOADER
 	select IEEE80211
 	---help---
           A driver for the Intel PRO/Wireless 2100 Network
 	  Connection 802.11b wireless network adapter.

           See <file:Documentation/networking/README.ipw2100> for information on
           the capabilities currently enabled in this driver and for tips
           for debugging issues and problems.

 	  In order to use this driver, you will need a firmware image for it.
           You can obtain the firmware from
 	  <http://ipw2100.sf.net/>.  Once you have the firmware image, you
 	  will need to place it in /lib/firmware.

           You will also very likely need the Wireless Tools in order to
           configure your card:

           <http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html>.

           If you want to compile the driver as a module ( = code which can be
           inserted in and removed from the running kernel whenever you want),
           say M here and read <file:Documentation/kbuild/modules.txt>.
           The module will be called ipw2100.ko.

 config IPW2100_MONITOR
         bool "Enable promiscuous mode"
         depends on IPW2100
         ---help---
 	  Enables promiscuous/monitor mode support for the ipw2100 driver.
 	  With this feature compiled into the driver, you can switch to
 	  promiscuous mode via the Wireless Tool's Monitor mode.  While in this
 	  mode, no packets can be sent.

 config IPW2100_DEBUG
 	bool "Enable full debugging output in IPW2100 module."
 	depends on IPW2100
 	---help---
 	  This option will enable debug tracing output for the IPW2100.

 	  This will result in the kernel module being ~60k larger.  You can
 	  control which debug output is sent to the kernel log by setting the
 	  value in

 	  /sys/bus/pci/drivers/ipw2100/debug_level

 	  This entry will only exist if this option is enabled.

 	  If you are not trying to debug or develop the IPW2100 driver, you
 	  most likely want to say N here.

 config IPW2200
 	tristate "Intel PRO/Wireless 2200BG and 2915ABG Network Connection"
 	depends on PCI && WLAN_80211
 	select WIRELESS_EXT
 	select FW_LOADER
 	select IEEE80211
 	---help---
           A driver for the Intel PRO/Wireless 2200BG and 2915ABG Network
 	  Connection adapters.

           See <file:Documentation/networking/README.ipw2200> for
 	  information on the capabilities currently enabled in this
 	  driver and for tips for debugging issues and problems.

 	  In order to use this driver, you will need a firmware image for it.
           You can obtain the firmware from
 	  <http://ipw2200.sf.net/>.  See the above referenced README.ipw2200
 	  for information on where to install the firmware images.

           You will also very likely need the Wireless Tools in order to
           configure your card:

           <http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html>.

           If you want to compile the driver as a module ( = code which can be
           inserted in and removed from the running kernel whenever you want),
           say M here and read <file:Documentation/kbuild/modules.txt>.
           The module will be called ipw2200.ko.

 config IPW2200_MONITOR
         bool "Enable promiscuous mode"
         depends on IPW2200
         ---help---
 	  Enables promiscuous/monitor mode support for the ipw2200 driver.
 	  With this feature compiled into the driver, you can switch to
 	  promiscuous mode via the Wireless Tool's Monitor mode.  While in this
 	  mode, no packets can be sent.

 config IPW2200_RADIOTAP
 	bool "Enable radiotap format 802.11 raw packet support"
 	depends on IPW2200_MONITOR

 config IPW2200_PROMISCUOUS
 	bool "Enable creation of a RF radiotap promiscuous interface"
 	depends on IPW2200_MONITOR
 	select IPW2200_RADIOTAP
 	---help---
           Enables the creation of a second interface prefixed 'rtap'.
           This second interface will provide every received in radiotap
 	  format.

           This is useful for performing wireless network analysis while
           maintaining an active association.

           Example usage:

             % modprobe ipw2200 rtap_iface=1
             % ifconfig rtap0 up
             % tethereal -i rtap0

           If you do not specify 'rtap_iface=1' as a module parameter then
           the rtap interface will not be created and you will need to turn
           it on via sysfs:

             % echo 1 > /sys/bus/pci/drivers/ipw2200/*/rtap_iface

 config IPW2200_QOS
         bool "Enable QoS support"
         depends on IPW2200 && EXPERIMENTAL

 config IPW2200_DEBUG
 	bool "Enable full debugging output in IPW2200 module."
 	depends on IPW2200
 	---help---
 	  This option will enable low level debug tracing output for IPW2200.

 	  Note, normal debug code is already compiled in. This low level
 	  debug option enables debug on hot paths (e.g Tx, Rx, ISR) and
 	  will result in the kernel module being ~70 larger.  Most users
 	  will typically not need this high verbosity debug information.

 	  If you are not sure, say N here.

 config LIBERTAS
 	tristate "Marvell 8xxx Libertas WLAN driver support"
 	depends on WLAN_80211
 	select IEEE80211
 	select FW_LOADER
 	---help---
 	  A library for Marvell Libertas 8xxx devices.

 config LIBERTAS_USB
 	tristate "Marvell Libertas 8388 USB 802.11b/g cards"
 	depends on LIBERTAS && USB
 	---help---
 	  A driver for Marvell Libertas 8388 USB devices.

 config LIBERTAS_CS
 	tristate "Marvell Libertas 8385 CompactFlash 802.11b/g cards"
 	depends on LIBERTAS && PCMCIA && EXPERIMENTAL
 	select FW_LOADER
 	---help---
 	  A driver for Marvell Libertas 8385 CompactFlash devices.

 config LIBERTAS_DEBUG
 	bool "Enable full debugging output in the Libertas module."
 	depends on LIBERTAS
 	---help---
 	  Debugging support.

 config AIRO
 	tristate "Cisco/Aironet 34X/35X/4500/4800 ISA and PCI cards"
 	depends on ISA_DMA_API && WLAN_80211 && (PCI || BROKEN)
 	select WIRELESS_EXT
 	select CRYPTO
 	---help---
 	  This is the standard Linux driver to support Cisco/Aironet ISA and
 	  PCI 802.11 wireless cards.
 	  It supports the new 802.11b cards from Cisco (Cisco 34X, Cisco 35X
 	  - with or without encryption) as well as card before the Cisco
 	  acquisition (Aironet 4500, Aironet 4800, Aironet 4800B).

 	  This driver support both the standard Linux Wireless Extensions
 	  and Cisco proprietary API, so both the Linux Wireless Tools and the
 	  Cisco Linux utilities can be used to configure the card.

 	  The driver can be compiled as a module and will be named "airo".

 config HERMES
 	tristate "Hermes chipset 802.11b support (Orinoco/Prism2/Symbol)"
 	depends on (PPC_PMAC || PCI || PCMCIA) && WLAN_80211
 	select WIRELESS_EXT
 	---help---
 	  A driver for 802.11b wireless cards based on the "Hermes" or
 	  Intersil HFA384x (Prism 2) MAC controller.  This includes the vast
 	  majority of the PCMCIA 802.11b cards (which are nearly all rebadges)
 	  - except for the Cisco/Aironet cards.  Cards supported include the
 	  Apple Airport (not a PCMCIA card), WavelanIEEE/Orinoco,
 	  Cabletron/EnteraSys Roamabout, ELSA AirLancer, MELCO Buffalo, Avaya,
 	  IBM High Rate Wireless, Farralon Syyline, Samsung MagicLAN, Netgear
 	  MA401, LinkSys WPC-11, D-Link DWL-650, 3Com AirConnect, Intel
 	  PRO/Wireless, and Symbol Spectrum24 High Rate amongst others.

 	  This option includes the guts of the driver, but in order to
 	  actually use a card you will also need to enable support for PCMCIA
 	  Hermes cards, PLX9052 based PCI adaptors or the Apple Airport below.

 	  You will also very likely also need the Wireless Tools in order to
 	  configure your card and that /etc/pcmcia/wireless.opts works :
 	  <http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html>

 config APPLE_AIRPORT
 	tristate "Apple Airport support (built-in)"
 	depends on PPC_PMAC && HERMES
 	help
 	  Say Y here to support the Airport 802.11b wireless Ethernet hardware
 	  built into the Macintosh iBook and other recent PowerPC-based
 	  Macintosh machines. This is essentially a Lucent Orinoco card with
 	  a non-standard interface.

 	  This driver does not support the Airport Extreme (802.11b/g). Use
 	  the BCM43xx driver for Airport Extreme cards.

 config PLX_HERMES
 	tristate "Hermes in PLX9052 based PCI adaptor support (Netgear MA301 etc.)"
 	depends on PCI && HERMES
 	help
 	  Enable support for PCMCIA cards supported by the "Hermes" (aka
 	  orinoco) driver when used in PLX9052 based PCI adaptors.  These
 	  adaptors are not a full PCMCIA controller but act as a more limited
 	  PCI <-> PCMCIA bridge.  Several vendors sell such adaptors so that
 	  802.11b PCMCIA cards can be used in desktop machines.  The Netgear
 	  MA301 is such an adaptor.

 config TMD_HERMES
 	tristate "Hermes in TMD7160 based PCI adaptor support"
 	depends on PCI && HERMES
 	help
 	  Enable support for PCMCIA cards supported by the "Hermes" (aka
 	  orinoco) driver when used in TMD7160 based PCI adaptors.  These
 	  adaptors are not a full PCMCIA controller but act as a more limited
 	  PCI <-> PCMCIA bridge.  Several vendors sell such adaptors so that
 	  802.11b PCMCIA cards can be used in desktop machines.

 config NORTEL_HERMES
 	tristate "Nortel emobility PCI adaptor support"
 	depends on PCI && HERMES
 	help
 	  Enable support for PCMCIA cards supported by the "Hermes" (aka
 	  orinoco) driver when used in Nortel emobility PCI adaptors.  These
 	  adaptors are not full PCMCIA controllers, but act as a more limited
 	  PCI <-> PCMCIA bridge.

 config PCI_HERMES
 	tristate "Prism 2.5 PCI 802.11b adaptor support"
 	depends on PCI && HERMES
 	help
 	  Enable support for PCI and mini-PCI 802.11b wireless NICs based on
 	  the Prism 2.5 chipset.  These are true PCI cards, not the 802.11b
 	  PCMCIA cards bundled with PCI<->PCMCIA adaptors which are also
 	  common.  Some of the built-in wireless adaptors in laptops are of
 	  this variety.

 config PCMCIA_HERMES
 	tristate "Hermes PCMCIA card support"
 	depends on PCMCIA && HERMES
 	---help---
 	  A driver for "Hermes" chipset based PCMCIA wireless adaptors, such
 	  as the Lucent WavelanIEEE/Orinoco cards and their OEM (Cabletron/
 	  EnteraSys RoamAbout 802.11, ELSA Airlancer, Melco Buffalo and
 	  others).  It should also be usable on various Prism II based cards
 	  such as the Linksys, D-Link and Farallon Skyline.  It should also
 	  work on Symbol cards such as the 3Com AirConnect and Ericsson WLAN.

 	  You will very likely need the Wireless Tools in order to
 	  configure your card and that /etc/pcmcia/wireless.opts works:
 	  <http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html>.

 config PCMCIA_SPECTRUM
 	tristate "Symbol Spectrum24 Trilogy PCMCIA card support"
 	depends on PCMCIA && HERMES
 	select FW_LOADER
 	---help---

 	  This is a driver for 802.11b cards using RAM-loadable Symbol
 	  firmware, such as Symbol Wireless Networker LA4100, CompactFlash
 	  cards by Socket Communications and Intel PRO/Wireless 2011B.

 	  This driver requires firmware download on startup.  Utilities
 	  for downloading Symbol firmware are available at
 	  <http://sourceforge.net/projects/orinoco/>

 config ATMEL
       tristate "Atmel at76c50x chipset  802.11b support"
       depends on (PCI || PCMCIA) && WLAN_80211
       select WIRELESS_EXT
       select FW_LOADER
       select CRC32
        ---help---
         A driver 802.11b wireless cards based on the Atmel fast-vnet
         chips. This driver supports standard Linux wireless extensions.

         Many  cards based on this chipset do not have flash memory
         and need their firmware loaded at start-up. If yours is
         one of these, you will need to provide a firmware image
         to be loaded into the card by the driver. The Atmel
         firmware package can be downloaded from
         <http://www.thekelleys.org.uk/atmel>

 config PCI_ATMEL
       tristate "Atmel at76c506 PCI cards"
       depends on ATMEL && PCI
        ---help---
         Enable support for PCI and mini-PCI cards containing the
         Atmel at76c506 chip.

 config PCMCIA_ATMEL
 	tristate "Atmel at76c502/at76c504 PCMCIA cards"
 	depends on ATMEL && PCMCIA
 	select WIRELESS_EXT
 	select FW_LOADER
 	select CRC32
 	---help---
 	  Enable support for PCMCIA cards containing the
 	  Atmel at76c502 and at76c504 chips.

 config AIRO_CS
 	tristate "Cisco/Aironet 34X/35X/4500/4800 PCMCIA cards"
 	depends on PCMCIA && (BROKEN || !M32R) && WLAN_80211
 	select WIRELESS_EXT
 	select CRYPTO
 	select CRYPTO_AES
 	---help---
 	  This is the standard Linux driver to support Cisco/Aironet PCMCIA
 	  802.11 wireless cards.  This driver is the same as the Aironet
 	  driver part of the Linux Pcmcia package.
 	  It supports the new 802.11b cards from Cisco (Cisco 34X, Cisco 35X
 	  - with or without encryption) as well as card before the Cisco
 	  acquisition (Aironet 4500, Aironet 4800, Aironet 4800B). It also
 	  supports OEM of Cisco such as the DELL TrueMobile 4800 and Xircom
 	  802.11b cards.

 	  This driver support both the standard Linux Wireless Extensions
 	  and Cisco proprietary API, so both the Linux Wireless Tools and the
 	  Cisco Linux utilities can be used to configure the card.

 config PCMCIA_WL3501
       tristate "Planet WL3501 PCMCIA cards"
       depends on EXPERIMENTAL && PCMCIA && WLAN_80211
       select WIRELESS_EXT
        ---help---
          A driver for WL3501 PCMCIA 802.11 wireless cards made by Planet.
 	 It has basic support for Linux wireless extensions and initial
 	 micro support for ethtool.

 config PRISM54
 	tristate 'Intersil Prism GT/Duette/Indigo PCI/Cardbus'
 	depends on PCI && EXPERIMENTAL && WLAN_80211
 	select WIRELESS_EXT
 	select FW_LOADER
 	---help---
 	  Enable PCI and Cardbus support for the following chipset based cards:

 	  ISL3880 - Prism GT            802.11 b/g
 	  ISL3877 - Prism Indigo        802.11 a
 	  ISL3890 - Prism Duette        802.11 a/b/g

 	  For a complete list of supported cards visit <http://prism54.org>.
 	  Here is the latest confirmed list of supported cards:

 	  3com OfficeConnect 11g Cardbus Card aka 3CRWE154G72 (version 1)
 	  Allnet ALL0271 PCI Card
 	  Compex WL54G Cardbus Card
 	  Corega CG-WLCB54GT Cardbus Card
 	  D-Link Air Plus Xtreme G A1 Cardbus Card aka DWL-g650
 	  I-O Data WN-G54/CB Cardbus Card
 	  Kobishi XG-300 aka Z-Com Cardbus Card
 	  Netgear WG511 Cardbus Card
 	  Ovislink WL-5400PCI PCI Card
 	  Peabird WLG-PCI PCI Card
 	  Sitecom WL-100i Cardbus Card
 	  Sitecom WL-110i PCI Card
 	  SMC2802W -    EZ Connect g 2.4GHz 54 Mbps Wireless PCI Card
 	  SMC2835W -    EZ Connect g 2.4GHz 54 Mbps Wireless Cardbus Card
 	  SMC2835W-V2 - EZ Connect g 2.4GHz 54 Mbps Wireless Cardbus Card
 	  Z-Com XG-900 PCI Card
 	  Zyxel G-100 Cardbus Card

 	  If you enable this you will need a firmware file as well.
 	  You will need to copy this to /usr/lib/hotplug/firmware/isl3890.
 	  You can get this non-GPL'd firmware file from the Prism54 project page:
 	  <http://prism54.org>
 	  You will also need the /etc/hotplug/firmware.agent script from
 	  a current hotplug package.

 	  Note: You need a motherboard with DMA support to use any of these cards

 	  If you want to compile the driver as a module ( = code which can be
 	  inserted in and removed from the running kernel whenever you want),
 	  say M here and read <file:Documentation/kbuild/modules.txt>.
 	  The module will be called prism54.ko.

 config USB_ZD1201
 	tristate "USB ZD1201 based Wireless device support"
 	depends on USB && WLAN_80211
 	select WIRELESS_EXT
 	select FW_LOADER
 	---help---
 	  Say Y if you want to use wireless LAN adapters based on the ZyDAS
 	  ZD1201 chip.

 	  This driver makes the adapter appear as a normal Ethernet interface,
 	  typically on wlan0.

 	  The zd1201 device requires external firmware to be loaded.
 	  This can be found at http://linux-lc100020.sourceforge.net/

 	  To compile this driver as a module, choose M here: the
 	  module will be called zd1201.

 config RTL8187
 	tristate "Realtek 8187 USB support"
 	depends on MAC80211 && USB && WLAN_80211 && EXPERIMENTAL
 	select EEPROM_93CX6
 	---help---
 	  This is a driver for RTL8187 based cards.
 	  These are USB based chips found in cards such as:

 	  Netgear WG111v2

 	  Thanks to Realtek for their support!

 config ADM8211
 	tristate "ADMtek ADM8211 support"
 	depends on MAC80211 && PCI && WLAN_80211 && EXPERIMENTAL
 	select CRC32
 	select EEPROM_93CX6
 	---help---
 	  This driver is for ADM8211A, ADM8211B, and ADM8211C based cards.
 	  These are PCI/mini-PCI/Cardbus 802.11b chips found in cards such as:

 	  Xterasys Cardbus XN-2411b
 	  Blitz NetWave Point PC
 	  TrendNet 221pc
 	  Belkin F5D6001
 	  SMC 2635W
 	  Linksys WPC11 v1
 	  Fiberline FL-WL-200X
 	  3com Office Connect (3CRSHPW796)
 	  Corega WLPCIB-11
 	  SMC 2602W V2 EU
 	  D-Link DWL-520 Revision C

 	  However, some of these cards have been replaced with other chips
 	  like the RTL8180L (Xterasys Cardbus XN-2411b, Belkin F5D6001) or
 	  the Ralink RT2400 (SMC2635W) without a model number change.

 	  Thanks to Infineon-ADMtek for their support of this driver.

 source "drivers/net/wireless/hostap/Kconfig"
 source "drivers/net/wireless/bcm43xx/Kconfig"
 source "drivers/net/wireless/zd1211rw/Kconfig"

 endmenu
	#
	# Wireless LAN device configuration
	#

	menu "Wireless LAN"
	depends on !S390

	config WLAN_PRE80211
	bool "Wireless LAN (pre-802.11)"
	depends on NETDEVICES
	---help---
	Say Y if you have any pre-802.11 wireless LAN hardware.

	This option does not affect the kernel build, it only
	lets you choose drivers.

	config STRIP
	tristate "STRIP (Metricom starmode radio IP)"
	depends on INET && WLAN_PRE80211
	select WIRELESS_EXT
	---help---
	Say Y if you have a Metricom radio and intend to use Starmode Radio
	IP. STRIP is a radio protocol developed for the MosquitoNet project
	(on the WWW at <http://mosquitonet.stanford.edu/>) to send Internet
	traffic using Metricom radios. Metricom radios are small, battery
	powered, 100kbit/sec packet radio transceivers, about the size and
	weight of a cellular telephone. (You may also have heard them called
	"Metricom modems" but we avoid the term "modem" because it misleads
	many people into thinking that you can plug a Metricom modem into a
	phone line and use it as a modem.)

	You can use STRIP on any Linux machine with a serial port, although
	it is obviously most useful for people with laptop computers. If you
	think you might get a Metricom radio in the future, there is no harm
	in saying Y to STRIP now, except that it makes the kernel a bit
	bigger.

	To compile this as a module, choose M here: the module will be
	called strip.

	config ARLAN
	tristate "Aironet Arlan 655 & IC2200 DS support"
	depends on ISA && !64BIT && WLAN_PRE80211
	select WIRELESS_EXT
	---help---
	Aironet makes Arlan, a class of wireless LAN adapters. These use the
	www.Telxon.com chip, which is also used on several similar cards.
	This driver is tested on the 655 and IC2200 series cards. Look at
	<http://www.ylenurme.ee/~elmer/655/> for the latest information.

	The driver is built as two modules, arlan and arlan-proc. The latter
	is the /proc interface and is not needed most of time.

	On some computers the card ends up in non-valid state after some
	time. Use a ping-reset script to clear it.

	config WAVELAN
	tristate "AT&T/Lucent old WaveLAN & DEC RoamAbout DS ISA support"
	depends on ISA && WLAN_PRE80211
	select WIRELESS_EXT
	---help---
	The Lucent WaveLAN (formerly NCR and AT&T; or DEC RoamAbout DS) is
	a Radio LAN (wireless Ethernet-like Local Area Network) using the
	radio frequencies 900 MHz and 2.4 GHz.

	If you want to use an ISA WaveLAN card under Linux, say Y and read
	the Ethernet-HOWTO, available from
	<http://www.tldp.org/docs.html#howto>. Some more specific
	information is contained in
	<file:Documentation/networking/wavelan.txt> and in the source code
	<file:drivers/net/wavelan.p.h>.

	You will also need the wireless tools package available from
	<http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html>.
	Please read the man pages contained therein.

	To compile this driver as a module, choose M here: the module will be
	called wavelan.

	config PCMCIA_WAVELAN
	tristate "AT&T/Lucent old WaveLAN Pcmcia wireless support"
	depends on PCMCIA && WLAN_PRE80211
	select WIRELESS_EXT
	help
	Say Y here if you intend to attach an AT&T/Lucent Wavelan PCMCIA
	(PC-card) wireless Ethernet networking card to your computer. This
	driver is for the non-IEEE-802.11 Wavelan cards.

	To compile this driver as a module, choose M here: the module will be
	called wavelan_cs. If unsure, say N.

	config PCMCIA_NETWAVE
	tristate "Xircom Netwave AirSurfer Pcmcia wireless support"
	depends on PCMCIA && WLAN_PRE80211
	select WIRELESS_EXT
	help
	Say Y here if you intend to attach this type of PCMCIA (PC-card)
	wireless Ethernet networking card to your computer.

	To compile this driver as a module, choose M here: the module will be
	called netwave_cs. If unsure, say N.


	config WLAN_80211
	bool "Wireless LAN (IEEE 802.11)"
	depends on NETDEVICES
	---help---
	Say Y if you have any 802.11 wireless LAN hardware.

	This option does not affect the kernel build, it only
	lets you choose drivers.

	config PCMCIA_RAYCS
	tristate "Aviator/Raytheon 2.4MHz wireless support"
	depends on PCMCIA && WLAN_80211
	select WIRELESS_EXT
	---help---
	Say Y here if you intend to attach an Aviator/Raytheon PCMCIA
	(PC-card) wireless Ethernet networking card to your computer.
	Please read the file <file:Documentation/networking/ray_cs.txt> for
	details.

	To compile this driver as a module, choose M here: the module will be
	called ray_cs. If unsure, say N.

	config IPW2100
	tristate "Intel PRO/Wireless 2100 Network Connection"
	depends on PCI && WLAN_80211
	select WIRELESS_EXT
	select FW_LOADER
	select IEEE80211
	---help---
	A driver for the Intel PRO/Wireless 2100 Network
	Connection 802.11b wireless network adapter.

	See <file:Documentation/networking/README.ipw2100> for information on
	the capabilities currently enabled in this driver and for tips
	for debugging issues and problems.

	In order to use this driver, you will need a firmware image for it.
	You can obtain the firmware from
	<http://ipw2100.sf.net/>. Once you have the firmware image, you
	will need to place it in /lib/firmware.

	You will also very likely need the Wireless Tools in order to
	configure your card:

	<http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html>.

	If you want to compile the driver as a module ( = code which can be
	inserted in and removed from the running kernel whenever you want),
	say M here and read <file:Documentation/kbuild/modules.txt>.
	The module will be called ipw2100.ko.

	config IPW2100_MONITOR
	bool "Enable promiscuous mode"
	depends on IPW2100
	---help---
	Enables promiscuous/monitor mode support for the ipw2100 driver.
	With this feature compiled into the driver, you can switch to
	promiscuous mode via the Wireless Tool's Monitor mode. While in this
	mode, no packets can be sent.

	config IPW2100_DEBUG
	bool "Enable full debugging output in IPW2100 module."
	depends on IPW2100
	---help---
	This option will enable debug tracing output for the IPW2100.

	This will result in the kernel module being ~60k larger. You can
	control which debug output is sent to the kernel log by setting the
	value in

	/sys/bus/pci/drivers/ipw2100/debug_level

	This entry will only exist if this option is enabled.

	If you are not trying to debug or develop the IPW2100 driver, you
	most likely want to say N here.

	config IPW2200
	tristate "Intel PRO/Wireless 2200BG and 2915ABG Network Connection"
	depends on PCI && WLAN_80211
	select WIRELESS_EXT
	select FW_LOADER
	select IEEE80211
	---help---
	A driver for the Intel PRO/Wireless 2200BG and 2915ABG Network
	Connection adapters.

	See <file:Documentation/networking/README.ipw2200> for
	information on the capabilities currently enabled in this
	driver and for tips for debugging issues and problems.

	In order to use this driver, you will need a firmware image for it.
	You can obtain the firmware from
	<http://ipw2200.sf.net/>. See the above referenced README.ipw2200
	for information on where to install the firmware images.

	You will also very likely need the Wireless Tools in order to
	configure your card:

	<http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html>.

	If you want to compile the driver as a module ( = code which can be
	inserted in and removed from the running kernel whenever you want),
	say M here and read <file:Documentation/kbuild/modules.txt>.
	The module will be called ipw2200.ko.

	config IPW2200_MONITOR
	bool "Enable promiscuous mode"
	depends on IPW2200
	---help---
	Enables promiscuous/monitor mode support for the ipw2200 driver.
	With this feature compiled into the driver, you can switch to
	promiscuous mode via the Wireless Tool's Monitor mode. While in this
	mode, no packets can be sent.

	config IPW2200_RADIOTAP
	bool "Enable radiotap format 802.11 raw packet support"
	depends on IPW2200_MONITOR

	config IPW2200_PROMISCUOUS
	bool "Enable creation of a RF radiotap promiscuous interface"
	depends on IPW2200_MONITOR
	select IPW2200_RADIOTAP
	---help---
	Enables the creation of a second interface prefixed 'rtap'.
	This second interface will provide every received in radiotap
	format.

	This is useful for performing wireless network analysis while
	maintaining an active association.

	Example usage:

	% modprobe ipw2200 rtap_iface=1
	% ifconfig rtap0 up
	% tethereal -i rtap0

	If you do not specify 'rtap_iface=1' as a module parameter then
	the rtap interface will not be created and you will need to turn
	it on via sysfs:

	% echo 1 > /sys/bus/pci/drivers/ipw2200/*/rtap_iface

	config IPW2200_QOS
	bool "Enable QoS support"
	depends on IPW2200 && EXPERIMENTAL

	config IPW2200_DEBUG
	bool "Enable full debugging output in IPW2200 module."
	depends on IPW2200
	---help---
	This option will enable low level debug tracing output for IPW2200.

	Note, normal debug code is already compiled in. This low level
	debug option enables debug on hot paths (e.g Tx, Rx, ISR) and
	will result in the kernel module being ~70 larger. Most users
	will typically not need this high verbosity debug information.

	If you are not sure, say N here.

	config LIBERTAS
	tristate "Marvell 8xxx Libertas WLAN driver support"
	depends on WLAN_80211
	select IEEE80211
	select FW_LOADER
	---help---
	A library for Marvell Libertas 8xxx devices.

	config LIBERTAS_USB
	tristate "Marvell Libertas 8388 USB 802.11b/g cards"
	depends on LIBERTAS && USB
	---help---
	A driver for Marvell Libertas 8388 USB devices.

	config LIBERTAS_CS
	tristate "Marvell Libertas 8385 CompactFlash 802.11b/g cards"
	depends on LIBERTAS && PCMCIA && EXPERIMENTAL
	select FW_LOADER
	---help---
	A driver for Marvell Libertas 8385 CompactFlash devices.

	config LIBERTAS_DEBUG
	bool "Enable full debugging output in the Libertas module."
	depends on LIBERTAS
	---help---
	Debugging support.

	config AIRO
	tristate "Cisco/Aironet 34X/35X/4500/4800 ISA and PCI cards"
	depends on ISA_DMA_API && WLAN_80211 && (PCI \|\| BROKEN)
	select WIRELESS_EXT
	select CRYPTO
	---help---
	This is the standard Linux driver to support Cisco/Aironet ISA and
	PCI 802.11 wireless cards.
	It supports the new 802.11b cards from Cisco (Cisco 34X, Cisco 35X
	- with or without encryption) as well as card before the Cisco
	acquisition (Aironet 4500, Aironet 4800, Aironet 4800B).

	This driver support both the standard Linux Wireless Extensions
	and Cisco proprietary API, so both the Linux Wireless Tools and the
	Cisco Linux utilities can be used to configure the card.

	The driver can be compiled as a module and will be named "airo".

	config HERMES
	tristate "Hermes chipset 802.11b support (Orinoco/Prism2/Symbol)"
	depends on (PPC_PMAC \|\| PCI \|\| PCMCIA) && WLAN_80211
	select WIRELESS_EXT
	---help---
	A driver for 802.11b wireless cards based on the "Hermes" or
	Intersil HFA384x (Prism 2) MAC controller. This includes the vast
	majority of the PCMCIA 802.11b cards (which are nearly all rebadges)
	- except for the Cisco/Aironet cards. Cards supported include the
	Apple Airport (not a PCMCIA card), WavelanIEEE/Orinoco,
	Cabletron/EnteraSys Roamabout, ELSA AirLancer, MELCO Buffalo, Avaya,
	IBM High Rate Wireless, Farralon Syyline, Samsung MagicLAN, Netgear
	MA401, LinkSys WPC-11, D-Link DWL-650, 3Com AirConnect, Intel
	PRO/Wireless, and Symbol Spectrum24 High Rate amongst others.

	This option includes the guts of the driver, but in order to
	actually use a card you will also need to enable support for PCMCIA
	Hermes cards, PLX9052 based PCI adaptors or the Apple Airport below.

	You will also very likely also need the Wireless Tools in order to
	configure your card and that /etc/pcmcia/wireless.opts works :
	<http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html>

	config APPLE_AIRPORT
	tristate "Apple Airport support (built-in)"
	depends on PPC_PMAC && HERMES
	help
	Say Y here to support the Airport 802.11b wireless Ethernet hardware
	built into the Macintosh iBook and other recent PowerPC-based
	Macintosh machines. This is essentially a Lucent Orinoco card with
	a non-standard interface.

	This driver does not support the Airport Extreme (802.11b/g). Use
	the BCM43xx driver for Airport Extreme cards.

	config PLX_HERMES
	tristate "Hermes in PLX9052 based PCI adaptor support (Netgear MA301 etc.)"
	depends on PCI && HERMES
	help
	Enable support for PCMCIA cards supported by the "Hermes" (aka
	orinoco) driver when used in PLX9052 based PCI adaptors. These
	adaptors are not a full PCMCIA controller but act as a more limited
	PCI <-> PCMCIA bridge. Several vendors sell such adaptors so that
	802.11b PCMCIA cards can be used in desktop machines. The Netgear
	MA301 is such an adaptor.

	config TMD_HERMES
	tristate "Hermes in TMD7160 based PCI adaptor support"
	depends on PCI && HERMES
	help
	Enable support for PCMCIA cards supported by the "Hermes" (aka
	orinoco) driver when used in TMD7160 based PCI adaptors. These
	adaptors are not a full PCMCIA controller but act as a more limited
	PCI <-> PCMCIA bridge. Several vendors sell such adaptors so that
	802.11b PCMCIA cards can be used in desktop machines.

	config NORTEL_HERMES
	tristate "Nortel emobility PCI adaptor support"
	depends on PCI && HERMES
	help
	Enable support for PCMCIA cards supported by the "Hermes" (aka
	orinoco) driver when used in Nortel emobility PCI adaptors. These
	adaptors are not full PCMCIA controllers, but act as a more limited
	PCI <-> PCMCIA bridge.

	config PCI_HERMES
	tristate "Prism 2.5 PCI 802.11b adaptor support"
	depends on PCI && HERMES
	help
	Enable support for PCI and mini-PCI 802.11b wireless NICs based on
	the Prism 2.5 chipset. These are true PCI cards, not the 802.11b
	PCMCIA cards bundled with PCI<->PCMCIA adaptors which are also
	common. Some of the built-in wireless adaptors in laptops are of
	this variety.

	config PCMCIA_HERMES
	tristate "Hermes PCMCIA card support"
	depends on PCMCIA && HERMES
	---help---
	A driver for "Hermes" chipset based PCMCIA wireless adaptors, such
	as the Lucent WavelanIEEE/Orinoco cards and their OEM (Cabletron/
	EnteraSys RoamAbout 802.11, ELSA Airlancer, Melco Buffalo and
	others). It should also be usable on various Prism II based cards
	such as the Linksys, D-Link and Farallon Skyline. It should also
	work on Symbol cards such as the 3Com AirConnect and Ericsson WLAN.

	You will very likely need the Wireless Tools in order to
	configure your card and that /etc/pcmcia/wireless.opts works:
	<http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html>.

	config PCMCIA_SPECTRUM
	tristate "Symbol Spectrum24 Trilogy PCMCIA card support"
	depends on PCMCIA && HERMES
	select FW_LOADER
	---help---

	This is a driver for 802.11b cards using RAM-loadable Symbol
	firmware, such as Symbol Wireless Networker LA4100, CompactFlash
	cards by Socket Communications and Intel PRO/Wireless 2011B.

	This driver requires firmware download on startup. Utilities
	for downloading Symbol firmware are available at
	<http://sourceforge.net/projects/orinoco/>

	config ATMEL
	tristate "Atmel at76c50x chipset 802.11b support"
	depends on (PCI \|\| PCMCIA) && WLAN_80211
	select WIRELESS_EXT
	select FW_LOADER
	select CRC32
	---help---
	A driver 802.11b wireless cards based on the Atmel fast-vnet
	chips. This driver supports standard Linux wireless extensions.

	Many cards based on this chipset do not have flash memory
	and need their firmware loaded at start-up. If yours is
	one of these, you will need to provide a firmware image
	to be loaded into the card by the driver. The Atmel
	firmware package can be downloaded from
	<http://www.thekelleys.org.uk/atmel>

	config PCI_ATMEL
	tristate "Atmel at76c506 PCI cards"
	depends on ATMEL && PCI
	---help---
	Enable support for PCI and mini-PCI cards containing the
	Atmel at76c506 chip.

	config PCMCIA_ATMEL
	tristate "Atmel at76c502/at76c504 PCMCIA cards"
	depends on ATMEL && PCMCIA
	select WIRELESS_EXT
	select FW_LOADER
	select CRC32
	---help---
	Enable support for PCMCIA cards containing the
	Atmel at76c502 and at76c504 chips.

	config AIRO_CS
	tristate "Cisco/Aironet 34X/35X/4500/4800 PCMCIA cards"
	depends on PCMCIA && (BROKEN \|\| !M32R) && WLAN_80211
	select WIRELESS_EXT
	select CRYPTO
	select CRYPTO_AES
	---help---
	This is the standard Linux driver to support Cisco/Aironet PCMCIA
	802.11 wireless cards. This driver is the same as the Aironet
	driver part of the Linux Pcmcia package.
	It supports the new 802.11b cards from Cisco (Cisco 34X, Cisco 35X
	- with or without encryption) as well as card before the Cisco
	acquisition (Aironet 4500, Aironet 4800, Aironet 4800B). It also
	supports OEM of Cisco such as the DELL TrueMobile 4800 and Xircom
	802.11b cards.

	This driver support both the standard Linux Wireless Extensions
	and Cisco proprietary API, so both the Linux Wireless Tools and the
	Cisco Linux utilities can be used to configure the card.

	config PCMCIA_WL3501
	tristate "Planet WL3501 PCMCIA cards"
	depends on EXPERIMENTAL && PCMCIA && WLAN_80211
	select WIRELESS_EXT
	---help---
	A driver for WL3501 PCMCIA 802.11 wireless cards made by Planet.
	It has basic support for Linux wireless extensions and initial
	micro support for ethtool.

	config PRISM54
	tristate 'Intersil Prism GT/Duette/Indigo PCI/Cardbus'
	depends on PCI && EXPERIMENTAL && WLAN_80211
	select WIRELESS_EXT
	select FW_LOADER
	---help---
	Enable PCI and Cardbus support for the following chipset based cards:

	ISL3880 - Prism GT 802.11 b/g
	ISL3877 - Prism Indigo 802.11 a
	ISL3890 - Prism Duette 802.11 a/b/g

	For a complete list of supported cards visit <http://prism54.org>.
	Here is the latest confirmed list of supported cards:

	3com OfficeConnect 11g Cardbus Card aka 3CRWE154G72 (version 1)
	Allnet ALL0271 PCI Card
	Compex WL54G Cardbus Card
	Corega CG-WLCB54GT Cardbus Card
	D-Link Air Plus Xtreme G A1 Cardbus Card aka DWL-g650
	I-O Data WN-G54/CB Cardbus Card
	Kobishi XG-300 aka Z-Com Cardbus Card
	Netgear WG511 Cardbus Card
	Ovislink WL-5400PCI PCI Card
	Peabird WLG-PCI PCI Card
	Sitecom WL-100i Cardbus Card
	Sitecom WL-110i PCI Card
	SMC2802W - EZ Connect g 2.4GHz 54 Mbps Wireless PCI Card
	SMC2835W - EZ Connect g 2.4GHz 54 Mbps Wireless Cardbus Card
	SMC2835W-V2 - EZ Connect g 2.4GHz 54 Mbps Wireless Cardbus Card
	Z-Com XG-900 PCI Card
	Zyxel G-100 Cardbus Card

	If you enable this you will need a firmware file as well.
	You will need to copy this to /usr/lib/hotplug/firmware/isl3890.
	You can get this non-GPL'd firmware file from the Prism54 project page:
	<http://prism54.org>
	You will also need the /etc/hotplug/firmware.agent script from
	a current hotplug package.

	Note: You need a motherboard with DMA support to use any of these cards

	If you want to compile the driver as a module ( = code which can be
	inserted in and removed from the running kernel whenever you want),
	say M here and read <file:Documentation/kbuild/modules.txt>.
	The module will be called prism54.ko.

	config USB_ZD1201
	tristate "USB ZD1201 based Wireless device support"
	depends on USB && WLAN_80211
	select WIRELESS_EXT
	select FW_LOADER
	---help---
	Say Y if you want to use wireless LAN adapters based on the ZyDAS
	ZD1201 chip.

	This driver makes the adapter appear as a normal Ethernet interface,
	typically on wlan0.

	The zd1201 device requires external firmware to be loaded.
	This can be found at http://linux-lc100020.sourceforge.net/

	To compile this driver as a module, choose M here: the
	module will be called zd1201.

	config RTL8187
	tristate "Realtek 8187 USB support"
	depends on MAC80211 && USB && WLAN_80211 && EXPERIMENTAL
	select EEPROM_93CX6
	---help---
	This is a driver for RTL8187 based cards.
	These are USB based chips found in cards such as:

	Netgear WG111v2

	Thanks to Realtek for their support!

	config ADM8211
	tristate "ADMtek ADM8211 support"
	depends on MAC80211 && PCI && WLAN_80211 && EXPERIMENTAL
	select CRC32
	select EEPROM_93CX6
	---help---
	This driver is for ADM8211A, ADM8211B, and ADM8211C based cards.
	These are PCI/mini-PCI/Cardbus 802.11b chips found in cards such as:

	Xterasys Cardbus XN-2411b
	Blitz NetWave Point PC
	TrendNet 221pc
	Belkin F5D6001
	SMC 2635W
	Linksys WPC11 v1
	Fiberline FL-WL-200X
	3com Office Connect (3CRSHPW796)
	Corega WLPCIB-11
	SMC 2602W V2 EU
	D-Link DWL-520 Revision C

	However, some of these cards have been replaced with other chips
	like the RTL8180L (Xterasys Cardbus XN-2411b, Belkin F5D6001) or
	the Ralink RT2400 (SMC2635W) without a model number change.

	Thanks to Infineon-ADMtek for their support of this driver.

	source "drivers/net/wireless/hostap/Kconfig"
	source "drivers/net/wireless/bcm43xx/Kconfig"
	source "drivers/net/wireless/zd1211rw/Kconfig"

	endmenu