| /****************************************************************************** |
| * |
| * Copyright(c) 2003 - 2011 Intel Corporation. All rights reserved. |
| * |
| * This program is free software; you can redistribute it and/or modify it |
| * under the terms of version 2 of the GNU General Public License as |
| * published by the Free Software Foundation. |
| * |
| * This program is distributed in the hope that it will be useful, but WITHOUT |
| * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or |
| * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for |
| * more details. |
| * |
| * You should have received a copy of the GNU General Public License along with |
| * this program; if not, write to the Free Software Foundation, Inc., |
| * 51 Franklin Street, Fifth Floor, Boston, MA 02110, USA |
| * |
| * The full GNU General Public License is included in this distribution in the |
| * file called LICENSE. |
| * |
| * Contact Information: |
| * Intel Linux Wireless <ilw@linux.intel.com> |
| * Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 |
| * |
| *****************************************************************************/ |
| |
| #ifndef __il_3945_h__ |
| #define __il_3945_h__ |
| |
| #include <linux/pci.h> /* for struct pci_device_id */ |
| #include <linux/kernel.h> |
| #include <net/ieee80211_radiotap.h> |
| |
| /* Hardware specific file defines the PCI IDs table for that hardware module */ |
| extern const struct pci_device_id il3945_hw_card_ids[]; |
| |
| #include "common.h" |
| |
| /* Highest firmware API version supported */ |
| #define IL3945_UCODE_API_MAX 2 |
| |
| /* Lowest firmware API version supported */ |
| #define IL3945_UCODE_API_MIN 1 |
| |
| #define IL3945_FW_PRE "iwlwifi-3945-" |
| #define _IL3945_MODULE_FIRMWARE(api) IL3945_FW_PRE #api ".ucode" |
| #define IL3945_MODULE_FIRMWARE(api) _IL3945_MODULE_FIRMWARE(api) |
| |
| /* Default noise level to report when noise measurement is not available. |
| * This may be because we're: |
| * 1) Not associated (4965, no beacon stats being sent to driver) |
| * 2) Scanning (noise measurement does not apply to associated channel) |
| * 3) Receiving CCK (3945 delivers noise info only for OFDM frames) |
| * Use default noise value of -127 ... this is below the range of measurable |
| * Rx dBm for either 3945 or 4965, so it can indicate "unmeasurable" to user. |
| * Also, -127 works better than 0 when averaging frames with/without |
| * noise info (e.g. averaging might be done in app); measured dBm values are |
| * always negative ... using a negative value as the default keeps all |
| * averages within an s8's (used in some apps) range of negative values. */ |
| #define IL_NOISE_MEAS_NOT_AVAILABLE (-127) |
| |
| /* Module parameters accessible from iwl-*.c */ |
| extern struct il_mod_params il3945_mod_params; |
| |
| struct il3945_rate_scale_data { |
| u64 data; |
| s32 success_counter; |
| s32 success_ratio; |
| s32 counter; |
| s32 average_tpt; |
| unsigned long stamp; |
| }; |
| |
| struct il3945_rs_sta { |
| spinlock_t lock; |
| struct il_priv *il; |
| s32 *expected_tpt; |
| unsigned long last_partial_flush; |
| unsigned long last_flush; |
| u32 flush_time; |
| u32 last_tx_packets; |
| u32 tx_packets; |
| u8 tgg; |
| u8 flush_pending; |
| u8 start_rate; |
| struct timer_list rate_scale_flush; |
| struct il3945_rate_scale_data win[RATE_COUNT_3945]; |
| #ifdef CONFIG_MAC80211_DEBUGFS |
| struct dentry *rs_sta_dbgfs_stats_table_file; |
| #endif |
| |
| /* used to be in sta_info */ |
| int last_txrate_idx; |
| }; |
| |
| /* |
| * The common struct MUST be first because it is shared between |
| * 3945 and 4965! |
| */ |
| struct il3945_sta_priv { |
| struct il_station_priv_common common; |
| struct il3945_rs_sta rs_sta; |
| }; |
| |
| enum il3945_antenna { |
| IL_ANTENNA_DIVERSITY, |
| IL_ANTENNA_MAIN, |
| IL_ANTENNA_AUX |
| }; |
| |
| /* |
| * RTS threshold here is total size [2347] minus 4 FCS bytes |
| * Per spec: |
| * a value of 0 means RTS on all data/management packets |
| * a value > max MSDU size means no RTS |
| * else RTS for data/management frames where MPDU is larger |
| * than RTS value. |
| */ |
| #define DEFAULT_RTS_THRESHOLD 2347U |
| #define MIN_RTS_THRESHOLD 0U |
| #define MAX_RTS_THRESHOLD 2347U |
| #define MAX_MSDU_SIZE 2304U |
| #define MAX_MPDU_SIZE 2346U |
| #define DEFAULT_BEACON_INTERVAL 100U |
| #define DEFAULT_SHORT_RETRY_LIMIT 7U |
| #define DEFAULT_LONG_RETRY_LIMIT 4U |
| |
| #define IL_TX_FIFO_AC0 0 |
| #define IL_TX_FIFO_AC1 1 |
| #define IL_TX_FIFO_AC2 2 |
| #define IL_TX_FIFO_AC3 3 |
| #define IL_TX_FIFO_HCCA_1 5 |
| #define IL_TX_FIFO_HCCA_2 6 |
| #define IL_TX_FIFO_NONE 7 |
| |
| #define IEEE80211_DATA_LEN 2304 |
| #define IEEE80211_4ADDR_LEN 30 |
| #define IEEE80211_HLEN (IEEE80211_4ADDR_LEN) |
| #define IEEE80211_FRAME_LEN (IEEE80211_DATA_LEN + IEEE80211_HLEN) |
| |
| struct il3945_frame { |
| union { |
| struct ieee80211_hdr frame; |
| struct il3945_tx_beacon_cmd beacon; |
| u8 raw[IEEE80211_FRAME_LEN]; |
| u8 cmd[360]; |
| } u; |
| struct list_head list; |
| }; |
| |
| #define SEQ_TO_SN(seq) (((seq) & IEEE80211_SCTL_SEQ) >> 4) |
| #define SN_TO_SEQ(ssn) (((ssn) << 4) & IEEE80211_SCTL_SEQ) |
| #define MAX_SN ((IEEE80211_SCTL_SEQ) >> 4) |
| |
| #define SUP_RATE_11A_MAX_NUM_CHANNELS 8 |
| #define SUP_RATE_11B_MAX_NUM_CHANNELS 4 |
| #define SUP_RATE_11G_MAX_NUM_CHANNELS 12 |
| |
| #define IL_SUPPORTED_RATES_IE_LEN 8 |
| |
| #define SCAN_INTERVAL 100 |
| |
| #define MAX_TID_COUNT 9 |
| |
| #define IL_INVALID_RATE 0xFF |
| #define IL_INVALID_VALUE -1 |
| |
| #define STA_PS_STATUS_WAKE 0 |
| #define STA_PS_STATUS_SLEEP 1 |
| |
| struct il3945_ibss_seq { |
| u8 mac[ETH_ALEN]; |
| u16 seq_num; |
| u16 frag_num; |
| unsigned long packet_time; |
| struct list_head list; |
| }; |
| |
| #define IL_RX_HDR(x) ((struct il3945_rx_frame_hdr *)(\ |
| x->u.rx_frame.stats.payload + \ |
| x->u.rx_frame.stats.phy_count)) |
| #define IL_RX_END(x) ((struct il3945_rx_frame_end *)(\ |
| IL_RX_HDR(x)->payload + \ |
| le16_to_cpu(IL_RX_HDR(x)->len))) |
| #define IL_RX_STATS(x) (&x->u.rx_frame.stats) |
| #define IL_RX_DATA(x) (IL_RX_HDR(x)->payload) |
| |
| /****************************************************************************** |
| * |
| * Functions implemented in iwl3945-base.c which are forward declared here |
| * for use by iwl-*.c |
| * |
| *****************************************************************************/ |
| extern int il3945_calc_db_from_ratio(int sig_ratio); |
| extern void il3945_rx_replenish(void *data); |
| extern void il3945_rx_queue_reset(struct il_priv *il, struct il_rx_queue *rxq); |
| extern unsigned int il3945_fill_beacon_frame(struct il_priv *il, |
| struct ieee80211_hdr *hdr, |
| int left); |
| extern int il3945_dump_nic_event_log(struct il_priv *il, bool full_log, |
| char **buf, bool display); |
| extern void il3945_dump_nic_error_log(struct il_priv *il); |
| |
| /****************************************************************************** |
| * |
| * Functions implemented in iwl-[34]*.c which are forward declared here |
| * for use by iwl3945-base.c |
| * |
| * NOTE: The implementation of these functions are hardware specific |
| * which is why they are in the hardware specific files (vs. iwl-base.c) |
| * |
| * Naming convention -- |
| * il3945_ <-- Its part of iwlwifi (should be changed to il3945_) |
| * il3945_hw_ <-- Hardware specific (implemented in iwl-XXXX.c by all HW) |
| * iwlXXXX_ <-- Hardware specific (implemented in iwl-XXXX.c for XXXX) |
| * il3945_bg_ <-- Called from work queue context |
| * il3945_mac_ <-- mac80211 callback |
| * |
| ****************************************************************************/ |
| extern void il3945_hw_handler_setup(struct il_priv *il); |
| extern void il3945_hw_setup_deferred_work(struct il_priv *il); |
| extern void il3945_hw_cancel_deferred_work(struct il_priv *il); |
| extern int il3945_hw_rxq_stop(struct il_priv *il); |
| extern int il3945_hw_set_hw_params(struct il_priv *il); |
| extern int il3945_hw_nic_init(struct il_priv *il); |
| extern int il3945_hw_nic_stop_master(struct il_priv *il); |
| extern void il3945_hw_txq_ctx_free(struct il_priv *il); |
| extern void il3945_hw_txq_ctx_stop(struct il_priv *il); |
| extern int il3945_hw_nic_reset(struct il_priv *il); |
| extern int il3945_hw_txq_attach_buf_to_tfd(struct il_priv *il, |
| struct il_tx_queue *txq, |
| dma_addr_t addr, u16 len, u8 reset, |
| u8 pad); |
| extern void il3945_hw_txq_free_tfd(struct il_priv *il, struct il_tx_queue *txq); |
| extern int il3945_hw_get_temperature(struct il_priv *il); |
| extern int il3945_hw_tx_queue_init(struct il_priv *il, struct il_tx_queue *txq); |
| extern unsigned int il3945_hw_get_beacon_cmd(struct il_priv *il, |
| struct il3945_frame *frame, |
| u8 rate); |
| void il3945_hw_build_tx_cmd_rate(struct il_priv *il, struct il_device_cmd *cmd, |
| struct ieee80211_tx_info *info, |
| struct ieee80211_hdr *hdr, int sta_id); |
| extern int il3945_hw_reg_send_txpower(struct il_priv *il); |
| extern int il3945_hw_reg_set_txpower(struct il_priv *il, s8 power); |
| extern void il3945_hdl_stats(struct il_priv *il, struct il_rx_buf *rxb); |
| void il3945_hdl_c_stats(struct il_priv *il, struct il_rx_buf *rxb); |
| extern void il3945_disable_events(struct il_priv *il); |
| extern int il4965_get_temperature(const struct il_priv *il); |
| extern void il3945_post_associate(struct il_priv *il); |
| extern void il3945_config_ap(struct il_priv *il); |
| |
| extern int il3945_commit_rxon(struct il_priv *il, struct il_rxon_context *ctx); |
| |
| /** |
| * il3945_hw_find_station - Find station id for a given BSSID |
| * @bssid: MAC address of station ID to find |
| * |
| * NOTE: This should not be hardware specific but the code has |
| * not yet been merged into a single common layer for managing the |
| * station tables. |
| */ |
| extern u8 il3945_hw_find_station(struct il_priv *il, const u8 * bssid); |
| |
| extern struct ieee80211_ops il3945_hw_ops; |
| |
| extern __le32 il3945_get_antenna_flags(const struct il_priv *il); |
| extern int il3945_init_hw_rate_table(struct il_priv *il); |
| extern void il3945_reg_txpower_periodic(struct il_priv *il); |
| extern int il3945_txpower_set_from_eeprom(struct il_priv *il); |
| |
| extern int il3945_rs_next_rate(struct il_priv *il, int rate); |
| |
| /* scanning */ |
| int il3945_request_scan(struct il_priv *il, struct ieee80211_vif *vif); |
| void il3945_post_scan(struct il_priv *il); |
| |
| /* rates */ |
| extern const struct il3945_rate_info il3945_rates[RATE_COUNT_3945]; |
| |
| /* RSSI to dBm */ |
| #define IL39_RSSI_OFFSET 95 |
| |
| /* |
| * EEPROM related constants, enums, and structures. |
| */ |
| #define EEPROM_SKU_CAP_OP_MODE_MRC (1 << 7) |
| |
| /* |
| * Mapping of a Tx power level, at factory calibration temperature, |
| * to a radio/DSP gain table idx. |
| * One for each of 5 "sample" power levels in each band. |
| * v_det is measured at the factory, using the 3945's built-in power amplifier |
| * (PA) output voltage detector. This same detector is used during Tx of |
| * long packets in normal operation to provide feedback as to proper output |
| * level. |
| * Data copied from EEPROM. |
| * DO NOT ALTER THIS STRUCTURE!!! |
| */ |
| struct il3945_eeprom_txpower_sample { |
| u8 gain_idx; /* idx into power (gain) setup table ... */ |
| s8 power; /* ... for this pwr level for this chnl group */ |
| u16 v_det; /* PA output voltage */ |
| } __packed; |
| |
| /* |
| * Mappings of Tx power levels -> nominal radio/DSP gain table idxes. |
| * One for each channel group (a.k.a. "band") (1 for BG, 4 for A). |
| * Tx power setup code interpolates between the 5 "sample" power levels |
| * to determine the nominal setup for a requested power level. |
| * Data copied from EEPROM. |
| * DO NOT ALTER THIS STRUCTURE!!! |
| */ |
| struct il3945_eeprom_txpower_group { |
| struct il3945_eeprom_txpower_sample samples[5]; /* 5 power levels */ |
| s32 a, b, c, d, e; /* coefficients for voltage->power |
| * formula (signed) */ |
| s32 Fa, Fb, Fc, Fd, Fe; /* these modify coeffs based on |
| * frequency (signed) */ |
| s8 saturation_power; /* highest power possible by h/w in this |
| * band */ |
| u8 group_channel; /* "representative" channel # in this band */ |
| s16 temperature; /* h/w temperature at factory calib this band |
| * (signed) */ |
| } __packed; |
| |
| /* |
| * Temperature-based Tx-power compensation data, not band-specific. |
| * These coefficients are use to modify a/b/c/d/e coeffs based on |
| * difference between current temperature and factory calib temperature. |
| * Data copied from EEPROM. |
| */ |
| struct il3945_eeprom_temperature_corr { |
| u32 Ta; |
| u32 Tb; |
| u32 Tc; |
| u32 Td; |
| u32 Te; |
| } __packed; |
| |
| /* |
| * EEPROM map |
| */ |
| struct il3945_eeprom { |
| u8 reserved0[16]; |
| u16 device_id; /* abs.ofs: 16 */ |
| u8 reserved1[2]; |
| u16 pmc; /* abs.ofs: 20 */ |
| u8 reserved2[20]; |
| u8 mac_address[6]; /* abs.ofs: 42 */ |
| u8 reserved3[58]; |
| u16 board_revision; /* abs.ofs: 106 */ |
| u8 reserved4[11]; |
| u8 board_pba_number[9]; /* abs.ofs: 119 */ |
| u8 reserved5[8]; |
| u16 version; /* abs.ofs: 136 */ |
| u8 sku_cap; /* abs.ofs: 138 */ |
| u8 leds_mode; /* abs.ofs: 139 */ |
| u16 oem_mode; |
| u16 wowlan_mode; /* abs.ofs: 142 */ |
| u16 leds_time_interval; /* abs.ofs: 144 */ |
| u8 leds_off_time; /* abs.ofs: 146 */ |
| u8 leds_on_time; /* abs.ofs: 147 */ |
| u8 almgor_m_version; /* abs.ofs: 148 */ |
| u8 antenna_switch_type; /* abs.ofs: 149 */ |
| u8 reserved6[42]; |
| u8 sku_id[4]; /* abs.ofs: 192 */ |
| |
| /* |
| * Per-channel regulatory data. |
| * |
| * Each channel that *might* be supported by 3945 has a fixed location |
| * in EEPROM containing EEPROM_CHANNEL_* usage flags (LSB) and max regulatory |
| * txpower (MSB). |
| * |
| * Entries immediately below are for 20 MHz channel width. |
| * |
| * 2.4 GHz channels 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14 |
| */ |
| u16 band_1_count; /* abs.ofs: 196 */ |
| struct il_eeprom_channel band_1_channels[14]; /* abs.ofs: 198 */ |
| |
| /* |
| * 4.9 GHz channels 183, 184, 185, 187, 188, 189, 192, 196, |
| * 5.0 GHz channels 7, 8, 11, 12, 16 |
| * (4915-5080MHz) (none of these is ever supported) |
| */ |
| u16 band_2_count; /* abs.ofs: 226 */ |
| struct il_eeprom_channel band_2_channels[13]; /* abs.ofs: 228 */ |
| |
| /* |
| * 5.2 GHz channels 34, 36, 38, 40, 42, 44, 46, 48, 52, 56, 60, 64 |
| * (5170-5320MHz) |
| */ |
| u16 band_3_count; /* abs.ofs: 254 */ |
| struct il_eeprom_channel band_3_channels[12]; /* abs.ofs: 256 */ |
| |
| /* |
| * 5.5 GHz channels 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140 |
| * (5500-5700MHz) |
| */ |
| u16 band_4_count; /* abs.ofs: 280 */ |
| struct il_eeprom_channel band_4_channels[11]; /* abs.ofs: 282 */ |
| |
| /* |
| * 5.7 GHz channels 145, 149, 153, 157, 161, 165 |
| * (5725-5825MHz) |
| */ |
| u16 band_5_count; /* abs.ofs: 304 */ |
| struct il_eeprom_channel band_5_channels[6]; /* abs.ofs: 306 */ |
| |
| u8 reserved9[194]; |
| |
| /* |
| * 3945 Txpower calibration data. |
| */ |
| #define IL_NUM_TX_CALIB_GROUPS 5 |
| struct il3945_eeprom_txpower_group groups[IL_NUM_TX_CALIB_GROUPS]; |
| /* abs.ofs: 512 */ |
| struct il3945_eeprom_temperature_corr corrections; /* abs.ofs: 832 */ |
| u8 reserved16[172]; /* fill out to full 1024 byte block */ |
| } __packed; |
| |
| #define IL3945_EEPROM_IMG_SIZE 1024 |
| |
| /* End of EEPROM */ |
| |
| #define PCI_CFG_REV_ID_BIT_BASIC_SKU (0x40) /* bit 6 */ |
| #define PCI_CFG_REV_ID_BIT_RTP (0x80) /* bit 7 */ |
| |
| /* 4 DATA + 1 CMD. There are 2 HCCA queues that are not used. */ |
| #define IL39_NUM_QUEUES 5 |
| #define IL39_CMD_QUEUE_NUM 4 |
| |
| #define IL_DEFAULT_TX_RETRY 15 |
| |
| /*********************************************/ |
| |
| #define RFD_SIZE 4 |
| #define NUM_TFD_CHUNKS 4 |
| |
| #define TFD_CTL_COUNT_SET(n) (n << 24) |
| #define TFD_CTL_COUNT_GET(ctl) ((ctl >> 24) & 7) |
| #define TFD_CTL_PAD_SET(n) (n << 28) |
| #define TFD_CTL_PAD_GET(ctl) (ctl >> 28) |
| |
| /* Sizes and addresses for instruction and data memory (SRAM) in |
| * 3945's embedded processor. Driver access is via HBUS_TARG_MEM_* regs. */ |
| #define IL39_RTC_INST_LOWER_BOUND (0x000000) |
| #define IL39_RTC_INST_UPPER_BOUND (0x014000) |
| |
| #define IL39_RTC_DATA_LOWER_BOUND (0x800000) |
| #define IL39_RTC_DATA_UPPER_BOUND (0x808000) |
| |
| #define IL39_RTC_INST_SIZE (IL39_RTC_INST_UPPER_BOUND - \ |
| IL39_RTC_INST_LOWER_BOUND) |
| #define IL39_RTC_DATA_SIZE (IL39_RTC_DATA_UPPER_BOUND - \ |
| IL39_RTC_DATA_LOWER_BOUND) |
| |
| #define IL39_MAX_INST_SIZE IL39_RTC_INST_SIZE |
| #define IL39_MAX_DATA_SIZE IL39_RTC_DATA_SIZE |
| |
| /* Size of uCode instruction memory in bootstrap state machine */ |
| #define IL39_MAX_BSM_SIZE IL39_RTC_INST_SIZE |
| |
| static inline int |
| il3945_hw_valid_rtc_data_addr(u32 addr) |
| { |
| return (addr >= IL39_RTC_DATA_LOWER_BOUND && |
| addr < IL39_RTC_DATA_UPPER_BOUND); |
| } |
| |
| /* Base physical address of il3945_shared is provided to FH39_TSSR_CBB_BASE |
| * and &il3945_shared.rx_read_ptr[0] is provided to FH39_RCSR_RPTR_ADDR(0) */ |
| struct il3945_shared { |
| __le32 tx_base_ptr[8]; |
| } __packed; |
| |
| /************************************/ |
| /* iwl3945 Flow Handler Definitions */ |
| /************************************/ |
| |
| /** |
| * This I/O area is directly read/writable by driver (e.g. Linux uses writel()) |
| * Addresses are offsets from device's PCI hardware base address. |
| */ |
| #define FH39_MEM_LOWER_BOUND (0x0800) |
| #define FH39_MEM_UPPER_BOUND (0x1000) |
| |
| #define FH39_CBCC_TBL (FH39_MEM_LOWER_BOUND + 0x140) |
| #define FH39_TFDB_TBL (FH39_MEM_LOWER_BOUND + 0x180) |
| #define FH39_RCSR_TBL (FH39_MEM_LOWER_BOUND + 0x400) |
| #define FH39_RSSR_TBL (FH39_MEM_LOWER_BOUND + 0x4c0) |
| #define FH39_TCSR_TBL (FH39_MEM_LOWER_BOUND + 0x500) |
| #define FH39_TSSR_TBL (FH39_MEM_LOWER_BOUND + 0x680) |
| |
| /* TFDB (Transmit Frame Buffer Descriptor) */ |
| #define FH39_TFDB(_ch, buf) (FH39_TFDB_TBL + \ |
| ((_ch) * 2 + (buf)) * 0x28) |
| #define FH39_TFDB_CHNL_BUF_CTRL_REG(_ch) (FH39_TFDB_TBL + 0x50 * (_ch)) |
| |
| /* CBCC channel is [0,2] */ |
| #define FH39_CBCC(_ch) (FH39_CBCC_TBL + (_ch) * 0x8) |
| #define FH39_CBCC_CTRL(_ch) (FH39_CBCC(_ch) + 0x00) |
| #define FH39_CBCC_BASE(_ch) (FH39_CBCC(_ch) + 0x04) |
| |
| /* RCSR channel is [0,2] */ |
| #define FH39_RCSR(_ch) (FH39_RCSR_TBL + (_ch) * 0x40) |
| #define FH39_RCSR_CONFIG(_ch) (FH39_RCSR(_ch) + 0x00) |
| #define FH39_RCSR_RBD_BASE(_ch) (FH39_RCSR(_ch) + 0x04) |
| #define FH39_RCSR_WPTR(_ch) (FH39_RCSR(_ch) + 0x20) |
| #define FH39_RCSR_RPTR_ADDR(_ch) (FH39_RCSR(_ch) + 0x24) |
| |
| #define FH39_RSCSR_CHNL0_WPTR (FH39_RCSR_WPTR(0)) |
| |
| /* RSSR */ |
| #define FH39_RSSR_CTRL (FH39_RSSR_TBL + 0x000) |
| #define FH39_RSSR_STATUS (FH39_RSSR_TBL + 0x004) |
| |
| /* TCSR */ |
| #define FH39_TCSR(_ch) (FH39_TCSR_TBL + (_ch) * 0x20) |
| #define FH39_TCSR_CONFIG(_ch) (FH39_TCSR(_ch) + 0x00) |
| #define FH39_TCSR_CREDIT(_ch) (FH39_TCSR(_ch) + 0x04) |
| #define FH39_TCSR_BUFF_STTS(_ch) (FH39_TCSR(_ch) + 0x08) |
| |
| /* TSSR */ |
| #define FH39_TSSR_CBB_BASE (FH39_TSSR_TBL + 0x000) |
| #define FH39_TSSR_MSG_CONFIG (FH39_TSSR_TBL + 0x008) |
| #define FH39_TSSR_TX_STATUS (FH39_TSSR_TBL + 0x010) |
| |
| /* DBM */ |
| |
| #define FH39_SRVC_CHNL (6) |
| |
| #define FH39_RCSR_RX_CONFIG_REG_POS_RBDC_SIZE (20) |
| #define FH39_RCSR_RX_CONFIG_REG_POS_IRQ_RBTH (4) |
| |
| #define FH39_RCSR_RX_CONFIG_REG_BIT_WR_STTS_EN (0x08000000) |
| |
| #define FH39_RCSR_RX_CONFIG_REG_VAL_DMA_CHNL_EN_ENABLE (0x80000000) |
| |
| #define FH39_RCSR_RX_CONFIG_REG_VAL_RDRBD_EN_ENABLE (0x20000000) |
| |
| #define FH39_RCSR_RX_CONFIG_REG_VAL_MAX_FRAG_SIZE_128 (0x01000000) |
| |
| #define FH39_RCSR_RX_CONFIG_REG_VAL_IRQ_DEST_INT_HOST (0x00001000) |
| |
| #define FH39_RCSR_RX_CONFIG_REG_VAL_MSG_MODE_FH (0x00000000) |
| |
| #define FH39_TCSR_TX_CONFIG_REG_VAL_MSG_MODE_TXF (0x00000000) |
| #define FH39_TCSR_TX_CONFIG_REG_VAL_MSG_MODE_DRIVER (0x00000001) |
| |
| #define FH39_TCSR_TX_CONFIG_REG_VAL_DMA_CREDIT_DISABLE_VAL (0x00000000) |
| #define FH39_TCSR_TX_CONFIG_REG_VAL_DMA_CREDIT_ENABLE_VAL (0x00000008) |
| |
| #define FH39_TCSR_TX_CONFIG_REG_VAL_CIRQ_HOST_IFTFD (0x00200000) |
| |
| #define FH39_TCSR_TX_CONFIG_REG_VAL_CIRQ_RTC_NOINT (0x00000000) |
| |
| #define FH39_TCSR_TX_CONFIG_REG_VAL_DMA_CHNL_PAUSE (0x00000000) |
| #define FH39_TCSR_TX_CONFIG_REG_VAL_DMA_CHNL_ENABLE (0x80000000) |
| |
| #define FH39_TCSR_CHNL_TX_BUF_STS_REG_VAL_TFDB_VALID (0x00004000) |
| |
| #define FH39_TCSR_CHNL_TX_BUF_STS_REG_BIT_TFDB_WPTR (0x00000001) |
| |
| #define FH39_TSSR_TX_MSG_CONFIG_REG_VAL_SNOOP_RD_TXPD_ON (0xFF000000) |
| #define FH39_TSSR_TX_MSG_CONFIG_REG_VAL_ORDER_RD_TXPD_ON (0x00FF0000) |
| |
| #define FH39_TSSR_TX_MSG_CONFIG_REG_VAL_MAX_FRAG_SIZE_128B (0x00000400) |
| |
| #define FH39_TSSR_TX_MSG_CONFIG_REG_VAL_SNOOP_RD_TFD_ON (0x00000100) |
| #define FH39_TSSR_TX_MSG_CONFIG_REG_VAL_ORDER_RD_CBB_ON (0x00000080) |
| |
| #define FH39_TSSR_TX_MSG_CONFIG_REG_VAL_ORDER_RSP_WAIT_TH (0x00000020) |
| #define FH39_TSSR_TX_MSG_CONFIG_REG_VAL_RSP_WAIT_TH (0x00000005) |
| |
| #define FH39_TSSR_TX_STATUS_REG_BIT_BUFS_EMPTY(_ch) (BIT(_ch) << 24) |
| #define FH39_TSSR_TX_STATUS_REG_BIT_NO_PEND_REQ(_ch) (BIT(_ch) << 16) |
| |
| #define FH39_TSSR_TX_STATUS_REG_MSK_CHNL_IDLE(_ch) \ |
| (FH39_TSSR_TX_STATUS_REG_BIT_BUFS_EMPTY(_ch) | \ |
| FH39_TSSR_TX_STATUS_REG_BIT_NO_PEND_REQ(_ch)) |
| |
| #define FH39_RSSR_CHNL0_RX_STATUS_CHNL_IDLE (0x01000000) |
| |
| struct il3945_tfd_tb { |
| __le32 addr; |
| __le32 len; |
| } __packed; |
| |
| struct il3945_tfd { |
| __le32 control_flags; |
| struct il3945_tfd_tb tbs[4]; |
| u8 __pad[28]; |
| } __packed; |
| |
| #ifdef CONFIG_IWLEGACY_DEBUGFS |
| ssize_t il3945_ucode_rx_stats_read(struct file *file, char __user *user_buf, |
| size_t count, loff_t *ppos); |
| ssize_t il3945_ucode_tx_stats_read(struct file *file, char __user *user_buf, |
| size_t count, loff_t *ppos); |
| ssize_t il3945_ucode_general_stats_read(struct file *file, |
| char __user *user_buf, size_t count, |
| loff_t *ppos); |
| #endif |
| |
| #endif |