| if (BF537 || BF534 || BF536) |
| |
| menu "BF537 Specific Configuration" |
| |
| comment "Interrupt Priority Assignment" |
| menu "Priority" |
| |
| config IRQ_PLL_WAKEUP |
| int "IRQ_PLL_WAKEUP" |
| default 7 |
| config IRQ_DMA_ERROR |
| int "IRQ_DMA_ERROR Generic" |
| default 7 |
| config IRQ_ERROR |
| int "IRQ_ERROR: CAN MAC SPORT0 SPORT1 SPI UART0 UART1" |
| default 7 |
| config IRQ_RTC |
| int "IRQ_RTC" |
| default 8 |
| config IRQ_PPI |
| int "IRQ_PPI" |
| default 8 |
| config IRQ_SPORT0_RX |
| int "IRQ_SPORT0_RX" |
| default 9 |
| config IRQ_SPORT0_TX |
| int "IRQ_SPORT0_TX" |
| default 9 |
| config IRQ_SPORT1_RX |
| int "IRQ_SPORT1_RX" |
| default 9 |
| config IRQ_SPORT1_TX |
| int "IRQ_SPORT1_TX" |
| default 9 |
| config IRQ_TWI |
| int "IRQ_TWI" |
| default 10 |
| config IRQ_SPI |
| int "IRQ_SPI" |
| default 10 |
| config IRQ_UART0_RX |
| int "IRQ_UART0_RX" |
| default 10 |
| config IRQ_UART0_TX |
| int "IRQ_UART0_TX" |
| default 10 |
| config IRQ_UART1_RX |
| int "IRQ_UART1_RX" |
| default 10 |
| config IRQ_UART1_TX |
| int "IRQ_UART1_TX" |
| default 10 |
| config IRQ_CAN_RX |
| int "IRQ_CAN_RX" |
| default 11 |
| config IRQ_CAN_TX |
| int "IRQ_CAN_TX" |
| default 11 |
| config IRQ_MAC_RX |
| int "IRQ_MAC_RX" |
| default 11 |
| config IRQ_MAC_TX |
| int "IRQ_MAC_TX" |
| default 11 |
| config IRQ_TMR0 |
| int "IRQ_TMR0" |
| default 12 |
| config IRQ_TMR1 |
| int "IRQ_TMR1" |
| default 12 |
| config IRQ_TMR2 |
| int "IRQ_TMR2" |
| default 12 |
| config IRQ_TMR3 |
| int "IRQ_TMR3" |
| default 12 |
| config IRQ_TMR4 |
| int "IRQ_TMR4" |
| default 12 |
| config IRQ_TMR5 |
| int "IRQ_TMR5" |
| default 12 |
| config IRQ_TMR6 |
| int "IRQ_TMR6" |
| default 12 |
| config IRQ_TMR7 |
| int "IRQ_TMR7" |
| default 12 |
| config IRQ_PROG_INTA |
| int "IRQ_PROG_INTA" |
| default 12 |
| config IRQ_PORTG_INTB |
| int "IRQ_PORTG_INTB" |
| default 12 |
| config IRQ_MEM_DMA0 |
| int "IRQ_MEM_DMA0" |
| default 13 |
| config IRQ_MEM_DMA1 |
| int "IRQ_MEM_DMA1" |
| default 13 |
| config IRQ_WATCH |
| int "IRQ_WATCH" |
| default 13 |
| |
| help |
| Enter the priority numbers between 7-13 ONLY. Others are Reserved. |
| This applies to all the above. It is not recommended to assign the |
| highest priority number 7 to UART or any other device. |
| |
| endmenu |
| |
| endmenu |
| |
| endif |