Gitiles
Code Review Sign In
LeafOS / LeafOS-Devices / android_kernel_samsung_exynos9820 / 9850488201f0b0bcbded1eca53750d2fd6accfbb / . / drivers / tty / serial / samsung.c
blob: ba2c03261f86a822e4b4a7926f7440a751caff60 [file] [log] [blame]
/*
* Driver core for Samsung SoC onboard UARTs.
*
* Ben Dooks, Copyright (c) 2003-2008 Simtec Electronics
* http://armlinux.simtec.co.uk/
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
/* Hote on 2410 error handling
*
* The s3c2410 manual has a love/hate affair with the contents of the
* UERSTAT register in the UART blocks, and keeps marking some of the
* error bits as reserved. Having checked with the s3c2410x01,
* it copes with BREAKs properly, so I am happy to ignore the RESERVED
* feature from the latter versions of the manual.
*
* If it becomes aparrent that latter versions of the 2410 remove these
* bits, then action will have to be taken to differentiate the versions
* and change the policy on BREAK
*
* BJD, 04-Nov-2004
*/
#if defined(CONFIG_SERIAL_SAMSUNG_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
#define SUPPORT_SYSRQ
#endif
#include <linux/module.h>
#include <linux/ioport.h>
#include <linux/io.h>
#include <linux/platform_device.h>
#include <linux/slab.h>
#include <linux/init.h>
#include <linux/sysrq.h>
#include <linux/console.h>
#include <linux/tty.h>
#include <linux/tty_flip.h>
#include <linux/serial_core.h>
#include <linux/serial.h>
#include <linux/serial_s3c.h>
#include <linux/notifier.h>
#include <linux/delay.h>
#include <linux/clk.h>
#include <linux/suspend.h>
#include <linux/of.h>
#include <linux/sched.h>
#include <linux/sched/clock.h>
#include <linux/sched/signal.h>
#include <asm/irq.h>
#include "samsung.h"
#include "../../pinctrl/core.h"
#ifdef CONFIG_CPU_IDLE
#include <soc/samsung/exynos-pm.h>
#endif
#ifdef CONFIG_PM_DEVFREQ
#include <linux/pm_qos.h>
#endif
#include <linux/proc_fs.h>
#include <linux/seq_file.h>
#if defined(CONFIG_SERIAL_SAMSUNG_DEBUG) && \
defined(CONFIG_DEBUG_LL) && \
!defined(MODULE)
extern void printascii(const char *);
__printf(1, 2)
static void dbg(const char *fmt, ...)
{
va_list va;
char buff[256];
va_start(va, fmt);
vscnprintf(buff, sizeof(buff), fmt, va);
va_end(va);
printascii(buff);
}
#else
#define dbg(fmt, ...) do { if (0) no_printk(fmt, ##__VA_ARGS__); } while (0)
#endif
/* UART name and device definitions */
#define S3C24XX_SERIAL_NAME "ttySAC"
#define S3C24XX_SERIAL_MAJOR 204
#define S3C24XX_SERIAL_MINOR 64
/* Baudrate definition*/
#define MAX_BAUD 4000000
#define MIN_BAUD 0
#define DEFAULT_SOURCE_CLK 200000000
#if defined(CONFIG_SEC_FACTORY) // SEC_FACTORY
#define SERIAL_UART_TRACE 1
#define PROC_SERIAL_DIR "serial/uart"
#define SERIAL_UART_PORT_LINE 0
#endif
#define BT_UART_TRACE 1
#define PROC_DIR "bluetooth/uart"
#define BLUETOOTH_UART_PORT_LINE 1
/* macros to change one thing to another */
#define tx_enabled(port) ((port)->unused[0])
#define rx_enabled(port) ((port)->unused[1])
/* flag to ignore all characters coming in */
#define RXSTAT_DUMMY_READ (0x10000000)
static LIST_HEAD(drvdata_list);
s3c_wake_peer_t s3c2410_serial_wake_peer[CONFIG_SERIAL_SAMSUNG_UARTS];
EXPORT_SYMBOL_GPL(s3c2410_serial_wake_peer);
#define UART_LOOPBACK_MODE (0x1 << 0)
#define UART_DBG_MODE (0x1 << 1)
#define RTS_PINCTRL (1)
#define DEFAULT_PINCTRL (0)
unsigned char uart_log_buf[256] = {0, };
void s3c24xx_serial_rx_fifo_wait(void);
/* Allocate 800KB of buffer for UART logging */
#define LOG_BUFFER_SIZE (0x190000)
struct s3c24xx_uart_port *panic_port;
static int exynos_s3c24xx_panic_handler(struct notifier_block *nb,
unsigned long l, void *p)
{
struct uart_port *port = &panic_port->port;
dev_err(panic_port->port.dev, " Register dump\n"
"ULCON 0x%08x "
"UCON 0x%08x "
"UFCON 0x%08x\n"
"UMCON 0x%08x "
"UTRSTAT 0x%08x "
"UERSTAT 0x%08x "
"UMSTAT 0x%08x\n"
"UBRDIV 0x%08x "
"UINTP 0x%08x "
"UINTM 0x%08x\n"
, readl(port->membase + S3C2410_ULCON)
, readl(port->membase + S3C2410_UCON)
, readl(port->membase + S3C2410_UFCON)
, readl(port->membase + S3C2410_UMCON)
, readl(port->membase + S3C2410_UTRSTAT)
, readl(port->membase + S3C2410_UERSTAT)
, readl(port->membase + S3C2410_UMSTAT)
, readl(port->membase + S3C2410_UBRDIV)
, readl(port->membase + S3C64XX_UINTP)
, readl(port->membase + S3C64XX_UINTM)
);
return 0;
}
static struct notifier_block exynos_s3c24xx_panic_block = {
.notifier_call = exynos_s3c24xx_panic_handler,
};
static void uart_sfr_dump(struct s3c24xx_uart_port *ourport)
{
struct uart_port *port = &ourport->port;
dev_err(ourport->port.dev, " Register dump\n"
"ULCON 0x%08x "
"UCON 0x%08x "
"UFCON 0x%08x \n"
"UMCON 0x%08x "
"UTRSTAT 0x%08x "
"UERSTAT 0x%08x "
"UMSTAT 0x%08x \n"
"UBRDIV 0x%08x "
"UINTP 0x%08x "
"UINTM 0x%08x \n"
, readl(port->membase + S3C2410_ULCON)
, readl(port->membase + S3C2410_UCON)
, readl(port->membase + S3C2410_UFCON)
, readl(port->membase + S3C2410_UMCON)
, readl(port->membase + S3C2410_UTRSTAT)
, readl(port->membase + S3C2410_UERSTAT)
, readl(port->membase + S3C2410_UMSTAT)
, readl(port->membase + S3C2410_UBRDIV)
, readl(port->membase + S3C64XX_UINTP)
, readl(port->membase + S3C64XX_UINTM)
);
}
static void change_uart_gpio(int value, struct s3c24xx_uart_port *ourport)
{
int status = 0;
if (value) {
if (!IS_ERR(ourport->uart_pinctrl_tx_dat)) {
ourport->default_uart_pinctrl->state = NULL;
status = pinctrl_select_state(ourport->default_uart_pinctrl, ourport->uart_pinctrl_tx_dat);
if (status)
dev_err(ourport->port.dev, "Can't set TXD uart pins!!!\n");
else
udelay(10);
}
if (!IS_ERR(ourport->uart_pinctrl_rts)) {
ourport->default_uart_pinctrl->state = NULL;
status = pinctrl_select_state(ourport->default_uart_pinctrl, ourport->uart_pinctrl_rts);
if (status)
dev_err(ourport->port.dev, "Can't set RTS uart pins!!!\n");
}
} else {
if (!IS_ERR(ourport->uart_pinctrl_default)) {
ourport->default_uart_pinctrl->state = NULL;
status = pinctrl_select_state(ourport->default_uart_pinctrl, ourport->uart_pinctrl_default);
if (status)
dev_err(ourport->port.dev, "Can't set default uart pins!!!\n");
}
}
}
static void print_uart_mode(struct uart_port *port,
struct ktermios *termios, unsigned int baud)
{
printk(KERN_ERR "UART port%d configurations\n", port->line);
switch (termios->c_cflag & CSIZE) {
case CS5:
printk(KERN_ERR " - 5bits word length\n");
break;
case CS6:
printk(KERN_ERR " - 6bits word length\n");
break;
case CS7:
printk(KERN_ERR " - 7bits word length\n");
break;
case CS8:
default:
printk(KERN_ERR " - 8bits word length\n");
break;
}
if (termios->c_cflag & CSTOPB)
printk(KERN_ERR " - Use TWO stop bit\n");
else
printk(KERN_ERR " - Use one stop bit\n");
if (termios->c_cflag & CRTSCTS)
printk(KERN_ERR " - Use Autoflow control\n");
printk(KERN_ERR " - Baudrate : %u\n", baud);
}
static ssize_t
uart_dbg_show(struct device *dev, struct device_attribute *attr, char *buf)
{
ssize_t ret = 0;
ret += snprintf(buf + ret, PAGE_SIZE - ret,
"UART Debug Mode Configuration.\n");
ret += snprintf(buf + ret, PAGE_SIZE - ret,
"0 : Change loopback & DBG mode.\n");
ret += snprintf(buf + ret, PAGE_SIZE - ret,
"1 : Change DBG mode.\n");
ret += snprintf(buf + ret, PAGE_SIZE - ret,
"2 : Change Normal mode.\n");
if (ret < PAGE_SIZE - 1) {
ret += snprintf(buf+ret, PAGE_SIZE-ret, "\n");
} else {
buf[PAGE_SIZE-2] = '\n';
buf[PAGE_SIZE-1] = '\0';
ret = PAGE_SIZE-1;
}
return ret;
}
static ssize_t
uart_dbg_store(struct device *dev, struct device_attribute *attr,
const char *buf, size_t count)
{
int input_cmd = 0, ret;
struct s3c24xx_uart_port *ourport;
ret = sscanf(buf, "%d", &input_cmd);
list_for_each_entry(ourport, &drvdata_list, node) {
if (&ourport->pdev->dev != dev)
continue;
switch(input_cmd) {
case 0:
printk(KERN_ERR "Change UART%d to Loopback(DBG) mode\n",
ourport->port.line);
ourport->dbg_mode = UART_DBG_MODE | UART_LOOPBACK_MODE;
break;
case 1:
printk(KERN_ERR "Change UART%d to DBG mode\n",
ourport->port.line);
ourport->dbg_mode = UART_DBG_MODE;
break;
case 2:
printk(KERN_ERR "Change UART%d to normal mode\n",
ourport->port.line);
ourport->dbg_mode = 0;
break;
default:
printk(KERN_ERR "Wrong Command!(0/1/2)\n");
}
}
return count;
}
static DEVICE_ATTR(uart_dbg, 0640, uart_dbg_show, uart_dbg_store);
static ssize_t
uart_error_cnt_show(struct device *dev, struct device_attribute *attr, char *buf)
{
int ret = 0;
struct s3c24xx_uart_port *ourport;
sprintf(buf, "000 000 000 000\n");//init buf : overrun parity frame break count
list_for_each_entry(ourport, &drvdata_list, node) {
struct uart_port *port = &ourport->port;
if (&ourport->pdev->dev != dev)
continue;
ret = sprintf(buf, "%03x %03x %03x %03x\n", port->icount.overrun, 0, port->icount.frame, port->icount.brk);
}
return ret;
}
static DEVICE_ATTR(error_cnt, 0444, uart_error_cnt_show, NULL);
struct proc_dir_entry *bluetooth_dir, *bt_log_dir;
struct proc_dir_entry *serial_dir, *serial_log_dir;
static void uart_copy_to_local_buf(int dir, struct uart_local_buf *local_buf,
unsigned char *trace_buf, int len)
{
unsigned long long time;
unsigned long rem_nsec;
int i;
int cpu = raw_smp_processor_id();
time = cpu_clock(cpu);
rem_nsec = do_div(time, NSEC_PER_SEC);
if (local_buf->index + (len * 3 + 30) >= local_buf->size)
local_buf->index = 0;
local_buf->index += scnprintf(local_buf->buffer + local_buf->index,
local_buf->size - local_buf->index,
"[%5lu.%06lu] ",
(unsigned long)time, rem_nsec / NSEC_PER_USEC);
if (dir == 3) {
local_buf->index += scnprintf(local_buf->buffer + local_buf->index,
local_buf->size - local_buf->index, "[termios] ");
local_buf->index += scnprintf(local_buf->buffer + local_buf->index,
local_buf->size - local_buf->index,
"%s", trace_buf);
} else if (dir == 2) {
local_buf->index += scnprintf(local_buf->buffer + local_buf->index,
local_buf->size - local_buf->index, "[reg] ");
local_buf->index += scnprintf(local_buf->buffer + local_buf->index,
local_buf->size - local_buf->index,
"%s", trace_buf);
} else {
if (dir == 1) {
local_buf->index += scnprintf(local_buf->buffer + local_buf->index,
local_buf->size - local_buf->index, "[RX] ");
} else {
local_buf->index += scnprintf(local_buf->buffer + local_buf->index,
local_buf->size - local_buf->index, "[TX] ");
}
for (i = 0; i < len; i++) {
local_buf->index += scnprintf(local_buf->buffer + local_buf->index,
local_buf->size - local_buf->index,
"%02X ", trace_buf[i]);
}
}
local_buf->index += scnprintf(local_buf->buffer + local_buf->index,
local_buf->size - local_buf->index, "\n");
}
static void exynos_usi_init(struct uart_port *port);
static void exynos_usi_stop(struct uart_port *port);
static void s3c24xx_serial_resetport(struct uart_port *port,
struct s3c2410_uartcfg *cfg);
static void s3c24xx_serial_pm(struct uart_port *port, unsigned int level,
unsigned int old);
static struct uart_driver s3c24xx_uart_drv;
static inline void uart_clock_enable(struct s3c24xx_uart_port *ourport)
{
if (ourport->check_separated_clk)
clk_prepare_enable(ourport->separated_clk);
clk_prepare_enable(ourport->clk);
}
static inline void uart_clock_disable(struct s3c24xx_uart_port *ourport)
{
clk_disable_unprepare(ourport->clk);
if (ourport->check_separated_clk)
clk_disable_unprepare(ourport->separated_clk);
}
static inline struct s3c24xx_uart_port *to_ourport(struct uart_port *port)
{
return container_of(port, struct s3c24xx_uart_port, port);
}
/* translate a port to the device name */
static inline const char *s3c24xx_serial_portname(struct uart_port *port)
{
return to_platform_device(port->dev)->name;
}
static int s3c24xx_serial_txempty_nofifo(struct uart_port *port)
{
return rd_regl(port, S3C2410_UTRSTAT) & S3C2410_UTRSTAT_TXE;
}
/*
* s3c64xx and later SoC's include the interrupt mask and status registers in
* the controller itself, unlike the s3c24xx SoC's which have these registers
* in the interrupt controller. Check if the port type is s3c64xx or higher.
*/
static int s3c24xx_serial_has_interrupt_mask(struct uart_port *port)
{
return to_ourport(port)->info->type == PORT_S3C6400;
}
static void s3c24xx_serial_rx_enable(struct uart_port *port)
{
unsigned long flags;
unsigned int ucon, ufcon;
int count = 10000;
spin_lock_irqsave(&port->lock, flags);
while (--count && !s3c24xx_serial_txempty_nofifo(port))
udelay(100);
ufcon = rd_regl(port, S3C2410_UFCON);
ufcon |= S3C2410_UFCON_RESETRX;
wr_regl(port, S3C2410_UFCON, ufcon);
ucon = rd_regl(port, S3C2410_UCON);
ucon |= S3C2410_UCON_RXIRQMODE;
wr_regl(port, S3C2410_UCON, ucon);
rx_enabled(port) = 1;
spin_unlock_irqrestore(&port->lock, flags);
}
static void s3c24xx_serial_rx_disable(struct uart_port *port)
{
unsigned long flags;
unsigned int ucon;
spin_lock_irqsave(&port->lock, flags);
ucon = rd_regl(port, S3C2410_UCON);
ucon &= ~S3C2410_UCON_RXIRQMODE;
wr_regl(port, S3C2410_UCON, ucon);
rx_enabled(port) = 0;
spin_unlock_irqrestore(&port->lock, flags);
}
static void s3c24xx_serial_stop_tx(struct uart_port *port)
{
struct s3c24xx_uart_port *ourport = to_ourport(port);
if (tx_enabled(port)) {
if (s3c24xx_serial_has_interrupt_mask(port))
__set_bit(S3C64XX_UINTM_TXD,
portaddrl(port, S3C64XX_UINTM));
else
disable_irq_nosync(ourport->tx_irq);
tx_enabled(port) = 0;
if (port->flags & UPF_CONS_FLOW)
s3c24xx_serial_rx_enable(port);
}
}
static void s3c24xx_serial_start_tx(struct uart_port *port)
{
struct s3c24xx_uart_port *ourport = to_ourport(port);
if (!tx_enabled(port)) {
if (port->flags & UPF_CONS_FLOW)
s3c24xx_serial_rx_disable(port);
if (s3c24xx_serial_has_interrupt_mask(port))
__clear_bit(S3C64XX_UINTM_TXD,
portaddrl(port, S3C64XX_UINTM));
else
enable_irq(ourport->tx_irq);
tx_enabled(port) = 1;
}
}
/* Throttle is called in n_tty_receive_buf_common */
static void s3c24xx_serial_throttle(struct uart_port *port)
{
unsigned long flags;
spin_lock_irqsave(&port->lock, flags);
__set_bit(S3C64XX_UINTM_RXD, portaddrl(port, S3C64XX_UINTM));
wr_regl(port, S3C64XX_UINTP, S3C64XX_UINTM_RXD_MSK);
spin_unlock_irqrestore(&port->lock, flags);
}
/* Unthrottle is called in n_tty_read */
static void s3c24xx_serial_unthrottle(struct uart_port *port)
{
unsigned long flags;
spin_lock_irqsave(&port->lock, flags);
__clear_bit(S3C64XX_UINTM_RXD, portaddrl(port, S3C64XX_UINTM));
spin_unlock_irqrestore(&port->lock, flags);
}
static void s3c24xx_serial_stop_rx(struct uart_port *port)
{
struct s3c24xx_uart_port *ourport = to_ourport(port);
if (rx_enabled(port)) {
dbg("s3c24xx_serial_stop_rx: port=%p\n", port);
if (s3c24xx_serial_has_interrupt_mask(port))
__set_bit(S3C64XX_UINTM_RXD,
portaddrl(port, S3C64XX_UINTM));
else
disable_irq_nosync(ourport->rx_irq);
rx_enabled(port) = 0;
}
}
static inline struct s3c24xx_uart_info
*s3c24xx_port_to_info(struct uart_port *port)
{
return to_ourport(port)->info;
}
static inline struct s3c2410_uartcfg
*s3c24xx_port_to_cfg(struct uart_port *port)
{
struct s3c24xx_uart_port *ourport;
if (port->dev == NULL)
return NULL;
ourport = container_of(port, struct s3c24xx_uart_port, port);
return ourport->cfg;
}
static int s3c24xx_serial_rx_fifocnt(struct s3c24xx_uart_port *ourport,
unsigned long ufstat)
{
struct s3c24xx_uart_info *info = ourport->info;
if (ufstat & info->rx_fifofull)
return ourport->port.fifosize;
return (ufstat & info->rx_fifomask) >> info->rx_fifoshift;
}
static int s3c24xx_serial_tx_fifocnt(struct s3c24xx_uart_port *ourport,
unsigned long ufstat)
{
struct s3c24xx_uart_info *info = ourport->info;
if (ufstat & info->tx_fifofull)
return ourport->port.fifosize;
return (ufstat & info->tx_fifomask) >> info->tx_fifoshift;
}
/* ? - where has parity gone?? */
#define S3C2410_UERSTAT_PARITY (0x1000)
static irqreturn_t
s3c24xx_serial_rx_chars(int irq, void *dev_id)
{
struct s3c24xx_uart_port *ourport = dev_id;
struct uart_port *port = &ourport->port;
unsigned int ufcon, ch, flag, ufstat, uerstat;
unsigned long flags;
int fifocnt = 0;
int max_count = port->fifosize;
unsigned char insert_buf[256] = {0, };
unsigned int insert_cnt = 0;
unsigned char trace_buf[256] = {0, };
int trace_cnt = 0;
spin_lock_irqsave(&port->lock, flags);
__set_bit(S3C64XX_UINTM_RXD, portaddrl(port, S3C64XX_UINTM));
wr_regl(port, S3C64XX_UINTP, S3C64XX_UINTM_RXD_MSK);
while (max_count-- > 0) {
/*
* Receive all characters known to be in FIFO
* before reading FIFO level again
*/
if (fifocnt == 0) {
ufstat = rd_regl(port, S3C2410_UFSTAT);
fifocnt = s3c24xx_serial_rx_fifocnt(ourport, ufstat);
if (fifocnt == 0)
break;
}
fifocnt--;
uerstat = rd_regl(port, S3C2410_UERSTAT);
ch = rd_regb(port, S3C2410_URXH);
if (port->flags & UPF_CONS_FLOW) {
int txe = s3c24xx_serial_txempty_nofifo(port);
if (rx_enabled(port)) {
if (!txe) {
rx_enabled(port) = 0;
continue;
}
} else {
if (txe) {
ufcon = rd_regl(port, S3C2410_UFCON);
ufcon |= S3C2410_UFCON_RESETRX;
wr_regl(port, S3C2410_UFCON, ufcon);
rx_enabled(port) = 1;
spin_unlock_irqrestore(&port->lock,
flags);
goto out;
}
continue;
}
}
/* insert the character into the buffer */
flag = TTY_NORMAL;
port->icount.rx++;
if (unlikely(uerstat & S3C2410_UERSTAT_ANY)) {
dbg("rxerr: port ch=0x%02x, rxs=0x%08x\n",
ch, uerstat);
uart_sfr_dump(ourport);
/* check for break */
if (uerstat & S3C2410_UERSTAT_BREAK) {
pr_err("[tty] uerstat & S3C2410_UERSTAT_BREAK1!\n");
port->icount.brk++;
if (uart_handle_break(port))
goto ignore_char;
}
if (uerstat & S3C2410_UERSTAT_FRAME) {
pr_err("[tty] uerstat & S3C2410_UERSTAT_FRAME!\n");
port->icount.frame++;
}
if (uerstat & S3C2410_UERSTAT_OVERRUN) {
pr_err("[tty] uerstat & S3C2410_UERSTAT_OVERRUN!\n");
port->icount.overrun++;
}
uerstat &= port->read_status_mask;
if (uerstat & S3C2410_UERSTAT_BREAK) {
pr_err("[tty] uerstat & S3C2410_UERSTAT_BREAK2!\n");
flag = TTY_BREAK;
}
else if (uerstat & S3C2410_UERSTAT_PARITY) {
pr_err("[tty] uerstat & S3C2410_UERSTAT_PARITY!\n");
flag = TTY_PARITY;
}
else if (uerstat & (S3C2410_UERSTAT_FRAME |
S3C2410_UERSTAT_OVERRUN))
flag = TTY_FRAME;
}
if (uart_handle_sysrq_char(port, ch))
goto ignore_char;
insert_buf[insert_cnt++] = ch;
if (ourport->uart_logging)
trace_buf[trace_cnt++] = ch;
ignore_char:
continue;
}
if (ourport->uart_logging && trace_cnt)
uart_copy_to_local_buf(1, &ourport->uart_local_buf, trace_buf, trace_cnt);
__clear_bit(S3C64XX_UINTM_RXD, portaddrl(port, S3C64XX_UINTM));
spin_unlock_irqrestore(&port->lock, flags);
tty_insert_flip_string(&port->state->port, insert_buf, insert_cnt);
tty_flip_buffer_push(&port->state->port);
out:
if (ourport->port.line == BLUETOOTH_UART_PORT_LINE) {
sprintf(uart_log_buf,"[0] UMCON:0x%08x UFSTAT:0x%08x UINTP:0x%08x UCON:0x%08x UMSTAT:0x%08x\n",
rd_regl(port, S3C2410_UMCON), rd_regl(port, S3C2410_UFSTAT), rd_regl(port, S3C2410_UINTP),
rd_regl(port, S3C2410_UCON), rd_regl(port, S3C2410_UMSTAT));
uart_copy_to_local_buf(2, &ourport->uart_local_buf, uart_log_buf, sizeof(uart_log_buf));
}
return IRQ_HANDLED;
}
static irqreturn_t s3c24xx_serial_tx_chars(int irq, void *id)
{
struct s3c24xx_uart_port *ourport = id;
struct uart_port *port = &ourport->port;
struct circ_buf *xmit = &port->state->xmit;
unsigned long flags;
int count = port->fifosize;
unsigned char trace_buf[256] = {0, };
int trace_cnt = 0;
if (ourport->port.line == BLUETOOTH_UART_PORT_LINE) {
sprintf(uart_log_buf,"[1] UMCON:0x%08x UFSTAT:0x%08x UINTP:0x%08x UCON:0x%08x UMSTAT:0x%08x\n",
rd_regl(port, S3C2410_UMCON), rd_regl(port, S3C2410_UFSTAT), rd_regl(port, S3C2410_UINTP),
rd_regl(port, S3C2410_UCON), rd_regl(port, S3C2410_UMSTAT));
uart_copy_to_local_buf(2, &ourport->uart_local_buf, uart_log_buf, sizeof(uart_log_buf));
}
spin_lock_irqsave(&port->lock, flags);
if (port->x_char) {
wr_regb(port, S3C2410_UTXH, port->x_char);
if (ourport->uart_logging)
trace_buf[trace_cnt++] = port->x_char;
port->icount.tx++;
port->x_char = 0;
goto out;
}
/* if there isn't anything more to transmit, or the uart is now
* stopped, disable the uart and exit
*/
if (uart_circ_empty(xmit) || uart_tx_stopped(port)) {
s3c24xx_serial_stop_tx(port);
goto out;
}
/* try and drain the buffer... */
while (!uart_circ_empty(xmit) && count-- > 0) {
if (rd_regl(port, S3C2410_UFSTAT) & ourport->info->tx_fifofull)
break;
wr_regb(port, S3C2410_UTXH, xmit->buf[xmit->tail]);
if (ourport->uart_logging)
trace_buf[trace_cnt++] = (unsigned char)xmit->buf[xmit->tail];
xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
port->icount.tx++;
}
if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
uart_write_wakeup(port);
if (uart_circ_empty(xmit))
s3c24xx_serial_stop_tx(port);
out:
wr_regl(port, S3C64XX_UINTP, S3C64XX_UINTM_TXD_MSK);
if (ourport->uart_logging && trace_cnt)
uart_copy_to_local_buf(0, &ourport->uart_local_buf, trace_buf, trace_cnt);
spin_unlock_irqrestore(&port->lock, flags);
if ((ourport->port.line == BLUETOOTH_UART_PORT_LINE) &&
signal_pending(current))
clear_thread_flag(TIF_SIGPENDING);
return IRQ_HANDLED;
}
#ifdef CONFIG_ARM_EXYNOS_DEVFREQ
static void s3c64xx_serial_qos_func(struct work_struct *work)
{
struct s3c24xx_uart_port *ourport =
container_of(work, struct s3c24xx_uart_port, qos_work.work);
struct uart_port *port = &ourport->port;
if (ourport->mif_qos_val)
pm_qos_update_request_timeout(&ourport->s3c24xx_uart_mif_qos,
ourport->mif_qos_val, ourport->qos_timeout);
if (ourport->cpu_qos_val)
pm_qos_update_request_timeout(&ourport->s3c24xx_uart_cpu_qos,
ourport->cpu_qos_val, ourport->qos_timeout);
if (ourport->uart_irq_affinity)
irq_set_affinity(port->irq, cpumask_of(ourport->uart_irq_affinity));
}
#endif
/* interrupt handler for s3c64xx and later SoC's.*/
static irqreturn_t s3c64xx_serial_handle_irq(int irq, void *id)
{
struct s3c24xx_uart_port *ourport = id;
struct uart_port *port = &ourport->port;
irqreturn_t ret = IRQ_HANDLED;
#ifdef CONFIG_PM_DEVFREQ
if ((ourport->mif_qos_val || ourport->cpu_qos_val)
&& ourport->qos_timeout)
schedule_delayed_work(&ourport->qos_work,
msecs_to_jiffies(100));
#endif
if (rd_regl(port, S3C64XX_UINTP) & S3C64XX_UINTM_RXD_MSK)
ret = s3c24xx_serial_rx_chars(irq, id);
if (rd_regl(port, S3C64XX_UINTP) & S3C64XX_UINTM_TXD_MSK)
ret = s3c24xx_serial_tx_chars(irq, id);
return ret;
}
static unsigned int s3c24xx_serial_tx_empty(struct uart_port *port)
{
struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port);
unsigned long ufstat = rd_regl(port, S3C2410_UFSTAT);
unsigned long ufcon = rd_regl(port, S3C2410_UFCON);
if (ufcon & S3C2410_UFCON_FIFOMODE) {
if ((ufstat & info->tx_fifomask) != 0 ||
(ufstat & info->tx_fifofull))
return 0;
return TIOCSER_TEMT;
}
return s3c24xx_serial_txempty_nofifo(port) ? TIOCSER_TEMT : 0;
}
/* no modem control lines */
static unsigned int s3c24xx_serial_get_mctrl(struct uart_port *port)
{
unsigned int umstat = rd_regb(port, S3C2410_UMSTAT);
if (umstat & S3C2410_UMSTAT_CTS)
return TIOCM_CAR | TIOCM_DSR | TIOCM_CTS;
else
return TIOCM_CAR | TIOCM_DSR;
}
static void s3c24xx_serial_set_mctrl(struct uart_port *port, unsigned int mctrl)
{
unsigned int umcon = rd_regl(port, S3C2410_UMCON);
struct s3c24xx_uart_port *ourport = to_ourport(port);
if (mctrl & TIOCM_RTS)
umcon |= S3C2410_UMCOM_RTS_LOW;
else
umcon &= ~S3C2410_UMCOM_RTS_LOW;
wr_regl(port, S3C2410_UMCON, umcon);
if (ourport->port.line == BLUETOOTH_UART_PORT_LINE) {
sprintf(uart_log_buf,"[2] UMCON:0x%08x UFSTAT:0x%08x UINTP:0x%08x UCON:0x%08x UMSTAT:0x%08x\n",
rd_regl(port, S3C2410_UMCON), rd_regl(port, S3C2410_UFSTAT), rd_regl(port, S3C2410_UINTP),
rd_regl(port, S3C2410_UCON), rd_regl(port, S3C2410_UMSTAT));
uart_copy_to_local_buf(2, &ourport->uart_local_buf, uart_log_buf, sizeof(uart_log_buf));
}
}
static void s3c24xx_serial_break_ctl(struct uart_port *port, int break_state)
{
unsigned long flags;
unsigned int ucon;
spin_lock_irqsave(&port->lock, flags);
ucon = rd_regl(port, S3C2410_UCON);
if (break_state)
ucon |= S3C2410_UCON_SBREAK;
else
ucon &= ~S3C2410_UCON_SBREAK;
wr_regl(port, S3C2410_UCON, ucon);
spin_unlock_irqrestore(&port->lock, flags);
}
static void s3c24xx_serial_shutdown(struct uart_port *port)
{
struct s3c24xx_uart_port *ourport = to_ourport(port);
if (ourport->tx_claimed) {
if (!s3c24xx_serial_has_interrupt_mask(port))
free_irq(ourport->tx_irq, ourport);
tx_enabled(port) = 0;
ourport->tx_claimed = 0;
}
if (ourport->rx_claimed) {
if (!s3c24xx_serial_has_interrupt_mask(port))
free_irq(ourport->rx_irq, ourport);
ourport->rx_claimed = 0;
rx_enabled(port) = 0;
}
/* Clear pending interrupts and mask all interrupts */
if (s3c24xx_serial_has_interrupt_mask(port)) {
free_irq(port->irq, ourport);
wr_regl(port, S3C64XX_UINTP, 0xf);
wr_regl(port, S3C64XX_UINTM, 0xf);
}
}
static int s3c24xx_serial_startup(struct uart_port *port)
{
struct s3c24xx_uart_port *ourport = to_ourport(port);
int ret;
dbg("s3c24xx_serial_startup: port=%p (%08llx,%p)\n",
port, (unsigned long long)port->mapbase, port->membase);
ourport->cfg->wake_peer[port->line] =
s3c2410_serial_wake_peer[port->line];
ourport->wake_peer_en = 1;
ourport->wake_peer_pended = 0;
rx_enabled(port) = 1;
ret = request_irq(ourport->rx_irq, s3c24xx_serial_rx_chars, 0,
s3c24xx_serial_portname(port), ourport);
if (ret != 0) {
dev_err(port->dev, "cannot get irq %d\n", ourport->rx_irq);
return ret;
}
ourport->rx_claimed = 1;
dbg("requesting tx irq...\n");
tx_enabled(port) = 1;
ret = request_irq(ourport->tx_irq, s3c24xx_serial_tx_chars, 0,
s3c24xx_serial_portname(port), ourport);
if (ret) {
dev_err(port->dev, "cannot get irq %d\n", ourport->tx_irq);
goto err;
}
ourport->tx_claimed = 1;
dbg("s3c24xx_serial_startup ok\n");
/* the port reset code should have done the correct
* register setup for the port controls */
return ret;
err:
s3c24xx_serial_shutdown(port);
return ret;
}
static int s3c64xx_serial_startup(struct uart_port *port)
{
struct s3c24xx_uart_port *ourport = to_ourport(port);
unsigned long flags;
int ret;
dbg("s3c64xx_serial_startup: port=%p (%08llx,%p)\n",
port, (unsigned long long)port->mapbase, port->membase);
ourport->cfg->wake_peer[port->line] =
s3c2410_serial_wake_peer[port->line];
ourport->wake_peer_en = 1;
spin_lock_irqsave(&port->lock, flags);
wr_regl(port, S3C64XX_UINTM, 0xf);
spin_unlock_irqrestore(&port->lock, flags);
if (ourport->use_default_irq == 1)
ret = devm_request_irq(port->dev, port->irq, s3c64xx_serial_handle_irq,
IRQF_SHARED, s3c24xx_serial_portname(port), ourport);
else
ret = request_threaded_irq(port->irq, NULL, s3c64xx_serial_handle_irq,
IRQF_ONESHOT, s3c24xx_serial_portname(port), ourport);
if (ret) {
dev_err(port->dev, "cannot get irq %d\n", port->irq);
return ret;
}
/* For compatibility with s3c24xx Soc's */
rx_enabled(port) = 1;
ourport->rx_claimed = 1;
tx_enabled(port) = 0;
ourport->tx_claimed = 1;
/* Enable Rx Interrupt */
spin_lock_irqsave(&port->lock, flags);
__clear_bit(S3C64XX_UINTM_RXD, portaddrl(port, S3C64XX_UINTM));
spin_unlock_irqrestore(&port->lock, flags);
dbg("s3c64xx_serial_startup ok\n");
return ret;
}
/* power power management control */
static void s3c24xx_serial_pm(struct uart_port *port, unsigned int level,
unsigned int old)
{
struct s3c24xx_uart_port *ourport = to_ourport(port);
unsigned int umcon;
switch (level) {
case S3C24XX_UART_PORT_SUSPEND:
if (!ourport->in_band_wakeup) {
/* disable auto flow control & set nRTS for High */
umcon = rd_regl(port, S3C2410_UMCON);
umcon &= ~(S3C2410_UMCOM_AFC | S3C2410_UMCOM_RTS_LOW);
wr_regl(port, S3C2410_UMCON, umcon);
if (ourport->port.line == BLUETOOTH_UART_PORT_LINE) {
sprintf(uart_log_buf,"[3] UMCON:0x%08x UFSTAT:0x%08x UINTP:0x%08x UCON:0x%08x UMSTAT:0x%08x\n",
rd_regl(port, S3C2410_UMCON), rd_regl(port, S3C2410_UFSTAT), rd_regl(port, S3C2410_UINTP),
rd_regl(port, S3C2410_UCON), rd_regl(port, S3C2410_UMSTAT));
uart_copy_to_local_buf(2, &ourport->uart_local_buf, uart_log_buf, sizeof(uart_log_buf));
}
}
uart_clock_disable(ourport);
break;
case S3C24XX_UART_PORT_RESUME:
uart_clock_enable(ourport);
if (ourport->port.line == BLUETOOTH_UART_PORT_LINE) {
sprintf(uart_log_buf,"[4] UMCON:0x%08x UFSTAT:0x%08x UINTP:0x%08x UCON:0x%08x UMSTAT:0x%08x\n",
rd_regl(port, S3C2410_UMCON), rd_regl(port, S3C2410_UFSTAT), rd_regl(port, S3C2410_UINTP),
rd_regl(port, S3C2410_UCON), rd_regl(port, S3C2410_UMSTAT));
uart_copy_to_local_buf(2, &ourport->uart_local_buf, uart_log_buf, sizeof(uart_log_buf));
}
exynos_usi_init(port);
s3c24xx_serial_resetport(port, s3c24xx_port_to_cfg(port));
break;
default:
dev_err(port->dev, "s3c24xx_serial: unknown pm %d\n", level);
}
}
/* baud rate calculation
*
* The UARTs on the S3C2410/S3C2440 can take their clocks from a number
* of different sources, including the peripheral clock ("pclk") and an
* external clock ("uclk"). The S3C2440 also adds the core clock ("fclk")
* with a programmable extra divisor.
*
* The following code goes through the clock sources, and calculates the
* baud clocks (and the resultant actual baud rates) and then tries to
* pick the closest one and select that.
*
*/
#define MAX_CLK_NAME_LENGTH 20
static unsigned int s3c24xx_serial_getclk(struct s3c24xx_uart_port *ourport,
unsigned int req_baud, struct clk **best_clk,
unsigned int *clk_num)
{
struct s3c24xx_uart_info *info = ourport->info;
unsigned long rate;
unsigned int cnt, baud, quot, clk_sel, best_quot = 0;
int calc_deviation, deviation = (1 << 30) - 1;
int ret;
clk_sel = (ourport->cfg->clk_sel) ? ourport->cfg->clk_sel :
ourport->info->def_clk_sel;
for (cnt = 0; cnt < info->num_clks; cnt++) {
if (!(clk_sel & (1 << cnt)))
continue;
rate = clk_get_rate(ourport->clk);
if (ourport->src_clk_rate && rate != ourport->src_clk_rate)
{
ret = clk_set_rate(ourport->clk, ourport->src_clk_rate);
if (ret < 0)
dev_err(&ourport->pdev->dev, "UART clk set failed\n");
rate = clk_get_rate(ourport->clk);
} else {
ret = clk_set_rate(ourport->clk, ourport->src_clk_rate);
if (ret < 0)
dev_err(&ourport->pdev->dev, "UART Default clk set failed\n");
rate = clk_get_rate(ourport->clk);
}
dev_info(&ourport->pdev->dev, " Clock rate : %ld\n", rate);
if (!rate)
continue;
if (ourport->info->has_divslot) {
unsigned long div = rate / req_baud;
/* The UDIVSLOT register on the newer UARTs allows us to
* get a divisor adjustment of 1/16th on the baud clock.
*
* We don't keep the UDIVSLOT value (the 16ths we
* calculated by not multiplying the baud by 16) as it
* is easy enough to recalculate.
*/
quot = div / 16;
baud = rate / div;
} else {
quot = (rate + (8 * req_baud)) / (16 * req_baud);
baud = rate / (quot * 16);
}
quot--;
calc_deviation = req_baud - baud;
if (calc_deviation < 0)
calc_deviation = -calc_deviation;
if (calc_deviation < deviation) {
*best_clk = ourport->clk;
best_quot = quot;
*clk_num = cnt;
deviation = calc_deviation;
}
}
return best_quot;
}
/* udivslot_table[]
*
* This table takes the fractional value of the baud divisor and gives
* the recommended setting for the UDIVSLOT register.
*/
static u16 udivslot_table[16] = {
[0] = 0x0000,
[1] = 0x0080,
[2] = 0x0808,
[3] = 0x0888,
[4] = 0x2222,
[5] = 0x4924,
[6] = 0x4A52,
[7] = 0x54AA,
[8] = 0x5555,
[9] = 0xD555,
[10] = 0xD5D5,
[11] = 0xDDD5,
[12] = 0xDDDD,
[13] = 0xDFDD,
[14] = 0xDFDF,
[15] = 0xFFDF,
};
static void s3c24xx_serial_set_termios(struct uart_port *port,
struct ktermios *termios,
struct ktermios *old)
{
struct s3c2410_uartcfg *cfg = s3c24xx_port_to_cfg(port);
struct s3c24xx_uart_port *ourport = to_ourport(port);
struct clk *clk = ERR_PTR(-EINVAL);
unsigned long flags;
unsigned int baud, quot, clk_sel = 0;
unsigned int ulcon;
unsigned int umcon;
unsigned int udivslot = 0;
unsigned int real_baud_rd, real_baud_ru = 0;
int calc_deviation_rd, calc_deviation_ru = 0;
/*
* We don't support modem control lines.
*/
termios->c_cflag &= ~(HUPCL | CMSPAR);
termios->c_cflag |= CLOCAL;
/*
* Ask the core to calculate the divisor for us.
*/
baud = uart_get_baud_rate(port, termios, old, MIN_BAUD, MAX_BAUD);
quot = s3c24xx_serial_getclk(ourport, baud, &clk, &clk_sel);
if (baud == 38400 && (port->flags & UPF_SPD_MASK) == UPF_SPD_CUST)
quot = port->custom_divisor;
if (IS_ERR(clk))
return;
/* setting clock for baud rate */
if (ourport->baudclk != clk) {
ourport->baudclk = clk;
ourport->baudclk_rate = clk ? clk_get_rate(clk) : 0;
}
if (ourport->info->has_divslot) {
unsigned int div = ourport->baudclk_rate / baud;
/*
* Find udivslot of the lowest error rate
*
* udivslot cannot be round-up to 0 because quot is fixed
*/
if((div & 15) != 15) {
real_baud_rd = ourport->baudclk_rate / div;
real_baud_ru = ourport->baudclk_rate / (div + 1);
calc_deviation_rd = baud - real_baud_rd;
calc_deviation_ru = baud - real_baud_ru;
if(calc_deviation_rd < 0)
calc_deviation_rd = -calc_deviation_rd;
if(calc_deviation_ru < 0)
calc_deviation_ru = -calc_deviation_ru;
if(calc_deviation_rd > calc_deviation_ru)
div = div + 1;
}
if (cfg->has_fracval) {
udivslot = (div & 15);
dbg("fracval = %04x\n", udivslot);
} else {
udivslot = udivslot_table[div & 15];
dbg("udivslot = %04x (div %d)\n", udivslot, div & 15);
}
}
switch (termios->c_cflag & CSIZE) {
case CS5:
dbg("config: 5bits/char\n");
ulcon = S3C2410_LCON_CS5;
break;
case CS6:
dbg("config: 6bits/char\n");
ulcon = S3C2410_LCON_CS6;
break;
case CS7:
dbg("config: 7bits/char\n");
ulcon = S3C2410_LCON_CS7;
break;
case CS8:
default:
dbg("config: 8bits/char\n");
ulcon = S3C2410_LCON_CS8;
break;
}
/* preserve original lcon IR settings */
if (!ourport->usi_v2)
ulcon |= (unsigned int)(cfg->ulcon & S3C2410_LCON_IRM);
if (termios->c_cflag & CSTOPB)
ulcon |= S3C2410_LCON_STOPB;
if (termios->c_cflag & PARENB) {
if (termios->c_cflag & PARODD)
ulcon |= S3C2410_LCON_PODD;
else
ulcon |= S3C2410_LCON_PEVEN;
} else {
ulcon |= S3C2410_LCON_PNONE;
}
spin_lock_irqsave(&port->lock, flags);
dbg("setting ulcon to %08x, brddiv to %d, udivslot %08x\n",
ulcon, quot, udivslot);
wr_regl(port, S3C2410_ULCON, ulcon);
wr_regl(port, S3C2410_UBRDIV, quot);
if (ourport->info->has_divslot)
wr_regl(port, S3C2443_DIVSLOT, udivslot);
port->status &= ~UPSTAT_AUTOCTS;
umcon = rd_regl(port, S3C2410_UMCON);
if (termios->c_cflag & CRTSCTS) {
umcon |= S3C2410_UMCOM_AFC;
port->status = UPSTAT_AUTOCTS;
} else {
umcon &= ~S3C2410_UMCOM_AFC;
}
wr_regl(port, S3C2410_UMCON, umcon);
dbg("uart: ulcon = 0x%08x, ucon = 0x%08x, ufcon = 0x%08x\n",
rd_regl(port, S3C2410_ULCON),
rd_regl(port, S3C2410_UCON),
rd_regl(port, S3C2410_UFCON));
if (ourport->dbg_mode & UART_DBG_MODE)
print_uart_mode(port, termios, baud);
/*
* Update the per-port timeout.
*/
uart_update_timeout(port, termios->c_cflag, baud);
/*
* Which character status flags are we interested in?
*/
port->read_status_mask = S3C2410_UERSTAT_OVERRUN;
if (termios->c_iflag & INPCK)
port->read_status_mask |= S3C2410_UERSTAT_FRAME |
S3C2410_UERSTAT_PARITY;
/*
* Which character status flags should we ignore?
*/
port->ignore_status_mask = 0;
if (termios->c_iflag & IGNPAR)
port->ignore_status_mask |= S3C2410_UERSTAT_OVERRUN;
if (termios->c_iflag & IGNBRK && termios->c_iflag & IGNPAR)
port->ignore_status_mask |= S3C2410_UERSTAT_FRAME;
/*
* Ignore all characters if CREAD is not set.
*/
if ((termios->c_cflag & CREAD) == 0)
port->ignore_status_mask |= RXSTAT_DUMMY_READ;
if (ourport->port.line == BLUETOOTH_UART_PORT_LINE) {
sprintf(uart_log_buf,"baudrate:%u ULCON:0x%08x UBRDIV:0x%08x UFRAVAL:0x%08x",
baud, rd_regl(port, S3C2410_ULCON),
rd_regl(port, S3C2410_UBRDIV),
rd_regl(port, S3C2443_DIVSLOT));
uart_copy_to_local_buf(3, &ourport->uart_local_buf, uart_log_buf, sizeof(uart_log_buf));
}
spin_unlock_irqrestore(&port->lock, flags);
}
static const char *s3c24xx_serial_type(struct uart_port *port)
{
switch (port->type) {
case PORT_S3C2410:
return "S3C2410";
case PORT_S3C2440:
return "S3C2440";
case PORT_S3C2412:
return "S3C2412";
case PORT_S3C6400:
return "S3C6400/10";
default:
return NULL;
}
}
#define MAP_SIZE (0x100)
static void s3c24xx_serial_release_port(struct uart_port *port)
{
release_mem_region(port->mapbase, MAP_SIZE);
}
static int s3c24xx_serial_request_port(struct uart_port *port)
{
const char *name = s3c24xx_serial_portname(port);
return request_mem_region(port->mapbase, MAP_SIZE, name) ? 0 : -EBUSY;
}
static void s3c24xx_serial_config_port(struct uart_port *port, int flags)
{
struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port);
if (flags & UART_CONFIG_TYPE &&
s3c24xx_serial_request_port(port) == 0)
port->type = info->type;
}
/*
* verify the new serial_struct (for TIOCSSERIAL).
*/
static int
s3c24xx_serial_verify_port(struct uart_port *port, struct serial_struct *ser)
{
struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port);
if (ser->type != PORT_UNKNOWN && ser->type != info->type)
return -EINVAL;
return 0;
}
static void s3c24xx_serial_wake_peer(struct uart_port *port)
{
struct s3c2410_uartcfg *cfg = s3c24xx_port_to_cfg(port);
struct s3c24xx_uart_port *ourport = to_ourport(port);
if (!ourport->wake_peer_en) {
ourport->wake_peer_pended = 1;
return ;
}
if (cfg->wake_peer[port->line])
cfg->wake_peer[port->line](port);
}
#ifdef CONFIG_SERIAL_SAMSUNG_CONSOLE
static struct console s3c24xx_serial_console;
static int __init s3c24xx_serial_console_init(void)
{
struct clk *console_clk;
char pclk_name[16], sclk_name[16];
snprintf(pclk_name, sizeof(pclk_name), "console-pclk%d", CONFIG_S3C_LOWLEVEL_UART_PORT);
snprintf(sclk_name, sizeof(sclk_name), "console-sclk%d", CONFIG_S3C_LOWLEVEL_UART_PORT);
pr_info("Enable clock for console to add reference counter\n");
console_clk = clk_get(NULL, pclk_name);
if (IS_ERR(console_clk)) {
pr_err("Can't get %s!(it's not err)\n", pclk_name);
} else {
clk_prepare_enable(console_clk);
}
console_clk = clk_get(NULL, sclk_name);
if (IS_ERR(console_clk)) {
pr_err("Can't get %s!(it's not err)\n", sclk_name);
} else {
clk_prepare_enable(console_clk);
}
register_console(&s3c24xx_serial_console);
return 0;
}
console_initcall(s3c24xx_serial_console_init);
#define S3C24XX_SERIAL_CONSOLE &s3c24xx_serial_console
#else
#define S3C24XX_SERIAL_CONSOLE NULL
#endif
#if defined(CONFIG_SERIAL_SAMSUNG_CONSOLE) && defined(CONFIG_CONSOLE_POLL)
static int s3c24xx_serial_get_poll_char(struct uart_port *port);
static void s3c24xx_serial_put_poll_char(struct uart_port *port,
unsigned char c);
#endif
static struct uart_ops s3c24xx_serial_ops = {
.pm = s3c24xx_serial_pm,
.tx_empty = s3c24xx_serial_tx_empty,
.get_mctrl = s3c24xx_serial_get_mctrl,
.set_mctrl = s3c24xx_serial_set_mctrl,
.stop_tx = s3c24xx_serial_stop_tx,
.start_tx = s3c24xx_serial_start_tx,
.throttle = s3c24xx_serial_throttle,
.unthrottle = s3c24xx_serial_unthrottle,
.stop_rx = s3c24xx_serial_stop_rx,
.break_ctl = s3c24xx_serial_break_ctl,
.startup = s3c24xx_serial_startup,
.shutdown = s3c24xx_serial_shutdown,
.set_termios = s3c24xx_serial_set_termios,
.type = s3c24xx_serial_type,
.release_port = s3c24xx_serial_release_port,
.request_port = s3c24xx_serial_request_port,
.config_port = s3c24xx_serial_config_port,
.verify_port = s3c24xx_serial_verify_port,
.wake_peer = s3c24xx_serial_wake_peer,
#if defined(CONFIG_SERIAL_SAMSUNG_CONSOLE) && defined(CONFIG_CONSOLE_POLL)
.poll_get_char = s3c24xx_serial_get_poll_char,
.poll_put_char = s3c24xx_serial_put_poll_char,
#endif
};
static struct uart_driver s3c24xx_uart_drv = {
.owner = THIS_MODULE,
.driver_name = "s3c2410_serial",
.nr = CONFIG_SERIAL_SAMSUNG_UARTS,
.cons = S3C24XX_SERIAL_CONSOLE,
.dev_name = S3C24XX_SERIAL_NAME,
.major = S3C24XX_SERIAL_MAJOR,
.minor = S3C24XX_SERIAL_MINOR,
};
#define __PORT_LOCK_UNLOCKED(i) \
__SPIN_LOCK_UNLOCKED(s3c24xx_serial_ports[i].port.lock)
static struct s3c24xx_uart_port
s3c24xx_serial_ports[CONFIG_SERIAL_SAMSUNG_UARTS] = {
[0] = {
.port = {
.lock = __PORT_LOCK_UNLOCKED(0),
.iotype = UPIO_MEM,
.uartclk = 0,
.fifosize = 16,
.ops = &s3c24xx_serial_ops,
.flags = UPF_BOOT_AUTOCONF,
.line = 0,
}
},
[1] = {
.port = {
.lock = __PORT_LOCK_UNLOCKED(1),
.iotype = UPIO_MEM,
.uartclk = 0,
.fifosize = 16,
.ops = &s3c24xx_serial_ops,
.flags = UPF_BOOT_AUTOCONF,
.line = 1,
}
},
#if CONFIG_SERIAL_SAMSUNG_UARTS > 2
[2] = {
.port = {
.lock = __PORT_LOCK_UNLOCKED(2),
.iotype = UPIO_MEM,
.uartclk = 0,
.fifosize = 16,
.ops = &s3c24xx_serial_ops,
.flags = UPF_BOOT_AUTOCONF,
.line = 2,
}
},
#endif
#if CONFIG_SERIAL_SAMSUNG_UARTS > 3
[3] = {
.port = {
.lock = __PORT_LOCK_UNLOCKED(3),
.iotype = UPIO_MEM,
.uartclk = 0,
.fifosize = 16,
.ops = &s3c24xx_serial_ops,
.flags = UPF_BOOT_AUTOCONF,
.line = 3,
}
},
#endif
#if CONFIG_SERIAL_SAMSUNG_UARTS > 4
[4] = {
.port = {
.lock = __PORT_LOCK_UNLOCKED(4),
.iotype = UPIO_MEM,
.uartclk = 0,
.fifosize = 16,
.ops = &s3c24xx_serial_ops,
.flags = UPF_BOOT_AUTOCONF,
.line = 4,
}
},
#endif
#if CONFIG_SERIAL_SAMSUNG_UARTS > 5
[5] = {
.port = {
.lock = __PORT_LOCK_UNLOCKED(5),
.iotype = UPIO_MEM,
.uartclk = 0,
.fifosize = 16,
.ops = &s3c24xx_serial_ops,
.flags = UPF_BOOT_AUTOCONF,
.line = 5,
}
},
#endif
};
static struct s3c24xx_uart_port *exynos_serial_default_port(int port_index)
{
s3c24xx_serial_ports[port_index].port.lock = __PORT_LOCK_UNLOCKED(port_index);
s3c24xx_serial_ports[port_index].port.iotype = UPIO_MEM;
s3c24xx_serial_ports[port_index].port.uartclk = 0;
s3c24xx_serial_ports[port_index].port.fifosize = 0;
s3c24xx_serial_ports[port_index].port.ops =
&s3c24xx_serial_ops;
s3c24xx_serial_ports[port_index].port.flags = UPF_BOOT_AUTOCONF;
s3c24xx_serial_ports[port_index].port.line = port_index;
return &s3c24xx_serial_ports[port_index];
}
#undef __PORT_LOCK_UNLOCKED
static void exynos_usi_init(struct uart_port *port)
{
/* USI_RESET is active High signal.
* Reset value of USI_RESET is 'h1 to drive stable value to PAD.
* Due to this feature, the USI_RESET must be cleared (set as '0')
* before transaction starts.
*/
wr_regl(port, USI_CON, USI_SET_RESET);
udelay(1);
wr_regl(port, USI_CON, USI_RESET);
udelay(1);
/* set the HWACG option bit in case of UART Rx mode.
* CLKREQ_ON = 1, CLKSTOP_ON = 0 (set USI_OPTION[2:1] = 2'h1)
*/
wr_regl(port, USI_OPTION, USI_HWACG_CLKREQ_ON);
udelay(1);
}
static void exynos_usi_stop(struct uart_port *port)
{
/* when USI CLKSTOP_ON is set high, this makes the
* Q-ch state enter into STOP state by driving both the
* IP_CLKREQ and IP_BUSACTREQ as low
*/
wr_regl(port, USI_OPTION, USI_HWACG_CLKSTOP_ON);
}
/* s3c24xx_serial_resetport
*
* reset the fifos and other the settings.
*/
static void s3c24xx_serial_resetport(struct uart_port *port,
struct s3c2410_uartcfg *cfg)
{
struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port);
struct s3c24xx_uart_port *ourport = to_ourport(port);
unsigned long ucon = rd_regl(port, S3C2410_UCON);
unsigned long umcon = rd_regl(port, S3C2410_UMCON);
unsigned int ucon_mask;
ucon_mask = info->clksel_mask;
if (info->type == PORT_S3C2440)
ucon_mask |= S3C2440_UCON0_DIVMASK;
ucon &= ucon_mask;
if (ourport->dbg_mode & UART_LOOPBACK_MODE) {
dev_err(port->dev, "Change Loopback mode!\n");
ucon |= S3C2443_UCON_LOOPBACK;
}
/* Set rts trigger level */
umcon &= ~S5PV210_UMCON_RTSTRIG32;
if (ourport->rts_trig_level && info->rts_trig_shift)
umcon |= ourport->rts_trig_level << info->rts_trig_shift;
wr_regl(port, S3C2410_UMCON, umcon);
/* To prevent unexpected Interrupt before enabling the channel */
wr_regl(port, S3C64XX_UINTM, 0xf);
/* reset both fifos */
wr_regl(port, S3C2410_UFCON, cfg->ufcon);
wr_regl(port, S3C2410_UCON, ucon | cfg->ucon);
}
/* s3c24xx_serial_init_port
*
* initialise a single serial port from the platform device given
*/
static int s3c24xx_serial_init_port(struct s3c24xx_uart_port *ourport,
struct platform_device *platdev)
{
struct uart_port *port = &ourport->port;
struct s3c2410_uartcfg *cfg = ourport->cfg;
struct resource *res;
char clkname[MAX_CLK_NAME_LENGTH];
int ret;
dbg("s3c24xx_serial_init_port: port=%p, platdev=%p\n", port, platdev);
if (platdev == NULL)
return -ENODEV;
if (port->mapbase != 0)
return -EINVAL;
/* setup info for port */
port->dev = &platdev->dev;
ourport->pdev = platdev;
/* Startup sequence is different for s3c64xx and higher SoC's */
if (s3c24xx_serial_has_interrupt_mask(port))
s3c24xx_serial_ops.startup = s3c64xx_serial_startup;
port->uartclk = 1;
if (cfg->uart_flags & UPF_CONS_FLOW) {
dbg("s3c24xx_serial_init_port: enabling flow control\n");
port->flags |= UPF_CONS_FLOW;
}
/* sort our the physical and virtual addresses for each UART */
res = platform_get_resource(platdev, IORESOURCE_MEM, 0);
if (res == NULL) {
dev_err(port->dev, "failed to find memory resource for uart\n");
return -EINVAL;
}
dbg("resource %pR)\n", res);
port->membase = devm_ioremap(port->dev, res->start, resource_size(res));
if (!port->membase) {
dev_err(port->dev, "failed to remap controller address\n");
return -EBUSY;
}
port->mapbase = res->start;
ret = platform_get_irq(platdev, 0);
if (ret < 0)
port->irq = 0;
else {
port->irq = ret;
ourport->rx_irq = ret;
ourport->tx_irq = ret + 1;
}
ret = platform_get_irq(platdev, 1);
if (ret > 0)
ourport->tx_irq = ret;
if (of_get_property(platdev->dev.of_node,
"samsung,separate-uart-clk", NULL))
ourport->check_separated_clk = 1;
else
ourport->check_separated_clk = 0;
if (of_property_read_u32(platdev->dev.of_node, "samsung,source-clock-rate", &ourport->src_clk_rate)){
dev_err(&platdev->dev, "No explicit src-clk. Use default src-clk\n");
ourport->src_clk_rate = DEFAULT_SOURCE_CLK;
}
snprintf(clkname, sizeof(clkname), "ipclk_uart%d", ourport->port.line);
ourport->clk = devm_clk_get(&platdev->dev, clkname);
if (IS_ERR(ourport->clk)) {
pr_err("%s: Controller clock not found\n",
dev_name(&platdev->dev));
return PTR_ERR(ourport->clk);
}
if (ourport->check_separated_clk) {
snprintf(clkname, sizeof(clkname), "gate_uart_clk%d", ourport->port.line);
ourport->separated_clk = devm_clk_get(&platdev->dev, clkname);
if (IS_ERR(ourport->separated_clk)) {
pr_err("%s: Controller clock not found\n",
dev_name(&platdev->dev));
return PTR_ERR(ourport->separated_clk);
}
ret = clk_prepare_enable(ourport->separated_clk);
if (ret) {
pr_err("uart: clock failed to prepare+enable: %d\n", ret);
return ret;
}
}
ret = clk_prepare_enable(ourport->clk);
if (ret) {
pr_err("uart: clock failed to prepare+enable: %d\n", ret);
return ret;
}
exynos_usi_init(port);
/* Keep all interrupts masked and cleared */
if (s3c24xx_serial_has_interrupt_mask(port)) {
wr_regl(port, S3C64XX_UINTM, 0xf);
wr_regl(port, S3C64XX_UINTP, 0xf);
wr_regl(port, S3C64XX_UINTSP, 0xf);
}
dbg("port: map=%pa, mem=%p, irq=%d (%d,%d), clock=%u\n",
&port->mapbase, port->membase, port->irq,
ourport->rx_irq, ourport->tx_irq, port->uartclk);
/* reset the fifos (and setup the uart) */
s3c24xx_serial_resetport(port, cfg);
return 0;
}
#ifdef CONFIG_SAMSUNG_CLOCK
static ssize_t s3c24xx_serial_show_clksrc(struct device *dev,
struct device_attribute *attr,
char *buf)
{
struct uart_port *port = s3c24xx_dev_to_port(dev);
struct s3c24xx_uart_port *ourport = to_ourport(port);
if (IS_ERR(ourport->baudclk))
return -EINVAL;
return snprintf(buf, PAGE_SIZE, "* %s\n",
ourport->baudclk->name ?: "(null)");
}
static DEVICE_ATTR(clock_source, S_IRUGO, s3c24xx_serial_show_clksrc, NULL);
#endif
static int exynos_s3c64xx_pm_notifier(struct notifier_block *notifier,
unsigned long pm_event, void *v)
{
struct s3c24xx_uart_port *ourport;
list_for_each_entry(ourport, &drvdata_list, node) {
if (ourport->port.line != BLUETOOTH_UART_PORT_LINE)
continue;
switch (pm_event) {
case PM_SUSPEND_PREPARE:
dev_info(&ourport->pdev->dev, "SUSPEND_PREPARE : Turn off BT wake_peer\n");
ourport->wake_peer_en = 0;
break;
case PM_POST_SUSPEND:
dev_info(&ourport->pdev->dev, "PM_POST_SUSPEND : Turn on BT wake_peer\n");
ourport->wake_peer_en = 1;
if (ourport->wake_peer_pended) {
ourport->wake_peer_pended = 0;
s3c24xx_serial_wake_peer(&ourport->port);
}
break;
}
}
return NOTIFY_OK;
}
static struct notifier_block exynos_s3c64xx_nb = {
.notifier_call = exynos_s3c64xx_pm_notifier,
};
/* Device driver serial port probe */
static const struct of_device_id s3c24xx_uart_dt_match[];
static int probe_index;
static inline struct s3c24xx_serial_drv_data *s3c24xx_get_driver_data(
struct platform_device *pdev)
{
#ifdef CONFIG_OF
if (pdev->dev.of_node) {
const struct of_device_id *match;
match = of_match_node(s3c24xx_uart_dt_match, pdev->dev.of_node);
return (struct s3c24xx_serial_drv_data *)match->data;
}
#endif
return (struct s3c24xx_serial_drv_data *)
platform_get_device_id(pdev)->driver_data;
}
void s3c24xx_serial_rx_fifo_wait(void)
{
struct s3c24xx_uart_port *ourport;
struct uart_port *port;
unsigned int fifo_stat;
unsigned long wait_time;
unsigned int fifo_count;
unsigned long flags;
fifo_count = 0;
list_for_each_entry(ourport, &drvdata_list, node) {
if (ourport->port.line != CONFIG_S3C_LOWLEVEL_UART_PORT)
continue;
port = &ourport->port;
spin_lock_irqsave(&port->lock, flags);
fifo_stat = rd_regl(port, S3C2410_UFSTAT);
fifo_count = s3c24xx_serial_rx_fifocnt(ourport, fifo_stat);
if (fifo_count) {
uart_clock_enable(ourport);
__clear_bit(S3C64XX_UINTM_RXD, portaddrl(port, S3C64XX_UINTM));
uart_clock_disable(ourport);
rx_enabled(port) = 1;
}
wait_time = jiffies + HZ;
do {
port = &ourport->port;
fifo_stat = rd_regl(port, S3C2410_UFSTAT);
cpu_relax();
} while (s3c24xx_serial_rx_fifocnt(ourport, fifo_stat) && time_before(jiffies, wait_time));
spin_unlock_irqrestore(&port->lock, flags);
if (rx_enabled(port))
s3c24xx_serial_stop_rx(port);
}
}
EXPORT_SYMBOL_GPL(s3c24xx_serial_rx_fifo_wait);
void s3c24xx_serial_fifo_wait(void)
{
struct s3c24xx_uart_port *ourport;
struct uart_port *port;
unsigned int fifo_stat;
unsigned long wait_time;
list_for_each_entry(ourport, &drvdata_list, node) {
if (ourport->port.line != CONFIG_S3C_LOWLEVEL_UART_PORT)
continue;
wait_time = jiffies + HZ / 4;
do {
port = &ourport->port;
fifo_stat = rd_regl(port, S3C2410_UFSTAT);
cpu_relax();
} while (s3c24xx_serial_tx_fifocnt(ourport, fifo_stat)
&& time_before(jiffies, wait_time));
}
}
EXPORT_SYMBOL_GPL(s3c24xx_serial_fifo_wait);
#define PT_L(x) x ? "BT" : "UART"
static void s3c24xx_print_reg_status(struct s3c24xx_uart_port *ourport)
{
struct uart_port *port = &ourport->port;
unsigned int ulcon = rd_regl(port, S3C2410_ULCON);
unsigned int ucon = rd_regl(port, S3C2410_UCON);
unsigned int ufcon = rd_regl(port, S3C2410_UFCON);
unsigned int umcon = rd_regl(port, S3C2410_UMCON);
unsigned int utrstat = rd_regl(port, S3C2410_UTRSTAT);
unsigned int ufstat = rd_regl(port, S3C2410_UFSTAT);
unsigned int umstat = rd_regl(port, S3C2410_UMSTAT);
unsigned int uerstat = rd_regl(port, S3C2410_UERSTAT);
int tx_fifo_full = ufstat & S5PV210_UFSTAT_TXFULL;
int tx_fifo_count = s3c24xx_serial_tx_fifocnt(ourport, ufstat);
int rx_fifo_full = ufstat & S5PV210_UFSTAT_RXFULL;
int rx_fifo_count = s3c24xx_serial_rx_fifocnt(ourport, ufstat);
pr_err("[%s]: ulcon = 0x%08x, ucon = 0x%08x, ufcon = 0x%08x\n, umcon = 0x%08x\n", PT_L(port->line), ulcon, ucon, ufcon, umcon);
pr_err("[%s]: utrstat = 0x%08x, ufstat = 0x%08x, umstat = 0x%08x\n", PT_L(port->line), utrstat, ufstat, umstat);
pr_err("[%s]: uerstat = 0x%08x\n", PT_L(port->line), uerstat);
pr_err("[%s]: tx_fifo_full = %d, tx_fifo_count = %d\n", PT_L(port->line), tx_fifo_full, tx_fifo_count);
pr_err("[%s]: rx_fifo_full = %d, rx_fifo_count = %d\n", PT_L(port->line), rx_fifo_full, rx_fifo_count);
}
#ifdef BT_UART_TRACE
static ssize_t s3c24xx_serial_bt_log(struct file *file, char __user *userbuf, size_t bytes, loff_t *off)
{
int ret;
struct s3c24xx_uart_port *ourport = &s3c24xx_serial_ports[BLUETOOTH_UART_PORT_LINE];
static int copied_bytes;
if (copied_bytes >= LOG_BUFFER_SIZE) {
struct uart_port *port;
port = &ourport->port;
copied_bytes = 0;
if (port && port->state->pm_state == UART_PM_STATE_ON)
s3c24xx_print_reg_status(ourport);
return 0;
}
if (copied_bytes + bytes < LOG_BUFFER_SIZE) {
ret = copy_to_user(userbuf, ourport->uart_local_buf.buffer+copied_bytes, bytes);
if (ret) {
pr_err("Failed to s3c24xx_serial_bt_log : %d\n", (int)ret);
return ret;
}
copied_bytes += bytes;
return bytes;
} else {
int byte_to_read = LOG_BUFFER_SIZE-copied_bytes;
ret = copy_to_user(userbuf, ourport->uart_local_buf.buffer+copied_bytes, byte_to_read);
if (ret) {
pr_err("Failed to s3c24xx_serial_bt_log : %d\n", (int)ret);
return ret;
}
copied_bytes += byte_to_read;
return byte_to_read;
}
return 0;
}
static const struct file_operations proc_fops_btlog = {
.owner = THIS_MODULE,
.read = s3c24xx_serial_bt_log,
};
#endif
#if defined(SERIAL_UART_TRACE)
static ssize_t s3c24xx_serial_uart_log(struct file *file, char __user *userbuf, size_t bytes, loff_t *off)
{
int ret;
struct s3c24xx_uart_port *ourport = &s3c24xx_serial_ports[SERIAL_UART_PORT_LINE];
static int copied_bytes;
if (copied_bytes >= LOG_BUFFER_SIZE) {
struct uart_port *port;
port = &ourport->port;
copied_bytes = 0;
if (port && port->state->pm_state == UART_PM_STATE_ON)
s3c24xx_print_reg_status(ourport);
return 0;
}
if (copied_bytes + bytes < LOG_BUFFER_SIZE) {
ret = copy_to_user(userbuf, ourport->uart_local_buf.buffer+copied_bytes, bytes);
if (ret) {
pr_err("Failed to s3c24xx_serial_serial_log : %d\n", (int)ret);
return ret;
}
copied_bytes += bytes;
return bytes;
} else {
int byte_to_read = LOG_BUFFER_SIZE-copied_bytes;
ret = copy_to_user(userbuf, ourport->uart_local_buf.buffer+copied_bytes, byte_to_read);
if (ret) {
pr_err("Failed to s3c24xx_serial_log : %d\n", (int)ret);
return ret;
}
copied_bytes += byte_to_read;
return byte_to_read;
}
return 0;
}
static const struct file_operations proc_fops_serial_log = {
.owner = THIS_MODULE,
.read = s3c24xx_serial_uart_log,
};
#endif
#ifdef CONFIG_CPU_IDLE
static int s3c24xx_serial_notifier(struct notifier_block *self,
unsigned long cmd, void *v)
{
struct s3c24xx_uart_port *ourport;
struct uart_port *port;
unsigned long flags;
unsigned int umcon;
switch (cmd) {
case LPA_ENTER:
s3c24xx_serial_fifo_wait();
break;
case SICD_ENTER:
case SICD_AUD_ENTER:
list_for_each_entry(ourport, &drvdata_list, node) {
if (ourport->port.line == CONFIG_S3C_LOWLEVEL_UART_PORT)
continue;
port = &ourport->port;
if (port->state->pm_state == UART_PM_STATE_OFF)
continue;
spin_lock_irqsave(&port->lock, flags);
/* disable auto flow control & set nRTS for High */
umcon = rd_regl(port, S3C2410_UMCON);
umcon &= ~(S3C2410_UMCOM_AFC | S3C2410_UMCOM_RTS_LOW);
wr_regl(port, S3C2410_UMCON, umcon);
spin_unlock_irqrestore(&port->lock, flags);
if (ourport->port.line == BLUETOOTH_UART_PORT_LINE) {
sprintf(uart_log_buf,"[5] UMCON:0x%08x UFSTAT:0x%08x UINTP:0x%08x UCON:0x%08x UMSTAT:0x%08x\n",
rd_regl(port, S3C2410_UMCON), rd_regl(port, S3C2410_UFSTAT), rd_regl(port, S3C2410_UINTP),
rd_regl(port, S3C2410_UCON), rd_regl(port, S3C2410_UMSTAT));
uart_copy_to_local_buf(2, &ourport->uart_local_buf, uart_log_buf, sizeof(uart_log_buf));
}
if (ourport->rts_control)
change_uart_gpio(RTS_PINCTRL, ourport);
}
s3c24xx_serial_fifo_wait();
break;
case SICD_EXIT:
case SICD_AUD_EXIT:
list_for_each_entry(ourport, &drvdata_list, node) {
if (ourport->port.line == CONFIG_S3C_LOWLEVEL_UART_PORT)
continue;
port = &ourport->port;
if (port->state->pm_state == UART_PM_STATE_OFF)
continue;
spin_lock_irqsave(&port->lock, flags);
/* enable auto flow control */
umcon = rd_regl(port, S3C2410_UMCON);
umcon |= S3C2410_UMCOM_AFC;
wr_regl(port, S3C2410_UMCON, umcon);
spin_unlock_irqrestore(&port->lock, flags);
if (ourport->port.line == BLUETOOTH_UART_PORT_LINE) {
sprintf(uart_log_buf,"[6] UMCON:0x%08x UFSTAT:0x%08x UINTP:0x%08x UCON:0x%08x UMSTAT:0x%08x\n",
rd_regl(port, S3C2410_UMCON), rd_regl(port, S3C2410_UFSTAT), rd_regl(port, S3C2410_UINTP),
rd_regl(port, S3C2410_UCON), rd_regl(port, S3C2410_UMSTAT));
uart_copy_to_local_buf(2, &ourport->uart_local_buf, uart_log_buf, sizeof(uart_log_buf));
}
if (ourport->rts_control)
change_uart_gpio(DEFAULT_PINCTRL, ourport);
}
break;
default:
break;
}
return NOTIFY_DONE;
}
static struct notifier_block s3c24xx_serial_notifier_block = {
.notifier_call = s3c24xx_serial_notifier,
};
#endif
static int s3c24xx_serial_probe(struct platform_device *pdev)
{
struct s3c24xx_uart_port *ourport;
int index = probe_index;
int ret, fifo_size;
int port_index = probe_index;
int rts_trig_level;
dbg("s3c24xx_serial_probe(%p) %d\n", pdev, index);
if (pdev->dev.of_node) {
ret = of_alias_get_id(pdev->dev.of_node, "uart");
if (ret < 0) {
dev_err(&pdev->dev, "UART aliases are not defined(%d).\n",
ret);
} else {
port_index = ret;
}
}
ourport = &s3c24xx_serial_ports[port_index];
if (ourport->port.line != port_index)
ourport = exynos_serial_default_port(port_index);
if (ourport->port.line >= CONFIG_SERIAL_SAMSUNG_UARTS) {
dev_err(&pdev->dev,
"the port %d exceeded CONFIG_SERIAL_SAMSUNG_UARTS(%d)\n"
, ourport->port.line, CONFIG_SERIAL_SAMSUNG_UARTS);
return -EINVAL;
}
ourport->drv_data = s3c24xx_get_driver_data(pdev);
if (!ourport->drv_data) {
dev_err(&pdev->dev, "could not find driver data\n");
return -ENODEV;
}
ourport->baudclk = ERR_PTR(-EINVAL);
ourport->info = ourport->drv_data->info;
ourport->cfg = (dev_get_platdata(&pdev->dev)) ?
dev_get_platdata(&pdev->dev) :
ourport->drv_data->def_cfg;
ourport->port.fifosize = (ourport->info->fifosize) ?
ourport->info->fifosize :
ourport->drv_data->fifosize[port_index];
if (of_get_property(pdev->dev.of_node, "samsung,uart-panic-log", NULL))
ourport->uart_panic_log = 1;
else
ourport->uart_panic_log = 0;
if (ourport->uart_panic_log) {
atomic_notifier_chain_register(&panic_notifier_list, &exynos_s3c24xx_panic_block);
panic_port = ourport;
}
if (of_get_property(pdev->dev.of_node, "samsung,usi-serial-v2", NULL))
ourport->usi_v2 = 1;
else
ourport->usi_v2 = 0;
if (of_get_property(pdev->dev.of_node, "samsung,rts-gpio-control", NULL)) {
ourport->rts_control = 1;
ourport->default_uart_pinctrl = devm_pinctrl_get(&pdev->dev);
if (IS_ERR(ourport->default_uart_pinctrl))
dev_err(&pdev->dev, "Can't get uart pinctrl!!!\n");
else {
ourport->uart_pinctrl_rts = pinctrl_lookup_state(ourport->default_uart_pinctrl,
"rts");
if (IS_ERR(ourport->uart_pinctrl_rts))
dev_err(&pdev->dev, "Can't get RTS pinstate!!!\n");
ourport->uart_pinctrl_tx_dat = pinctrl_lookup_state(ourport->default_uart_pinctrl,
"tx_dat");
ourport->uart_pinctrl_default = pinctrl_lookup_state(ourport->default_uart_pinctrl,
"default");
if (IS_ERR(ourport->uart_pinctrl_default))
dev_err(&pdev->dev, "Can't get Default pinstate!!!\n");
}
}
if (!of_property_read_u32(pdev->dev.of_node, "samsung,rts-trig-level",
&rts_trig_level)) {
ourport->rts_trig_level = rts_trig_level;
}
if (!of_property_read_u32(pdev->dev.of_node, "samsung,fifo-size",
&fifo_size)) {
ourport->port.fifosize = fifo_size;
ourport->info->fifosize = fifo_size;
} else {
dev_err(&pdev->dev,
"Please add FIFO size in device tree!(UART%d)\n", port_index);
return -EINVAL;
}
probe_index++;
dbg("%s: initialising port %p...\n", __func__, ourport);
#ifdef CONFIG_ARM_EXYNOS_DEVFREQ
if (of_property_read_u32(pdev->dev.of_node, "mif_qos_val",
&ourport->mif_qos_val))
ourport->mif_qos_val = 0;
if (of_property_read_u32(pdev->dev.of_node, "cpu_qos_val",
&ourport->cpu_qos_val))
ourport->cpu_qos_val = 0;
if (of_property_read_u32(pdev->dev.of_node, "irq_affinity",
&ourport->uart_irq_affinity))
ourport->uart_irq_affinity = 0;
if (of_property_read_u64(pdev->dev.of_node, "qos_timeout",
(u64 *)&ourport->qos_timeout))
ourport->qos_timeout = 0;
if ((ourport->mif_qos_val || ourport->cpu_qos_val)
&& ourport->qos_timeout) {
INIT_DELAYED_WORK(&ourport->qos_work,
s3c64xx_serial_qos_func);
/* request pm qos */
if (ourport->mif_qos_val)
pm_qos_add_request(&ourport->s3c24xx_uart_mif_qos,
PM_QOS_BUS_THROUGHPUT, 0);
if (ourport->cpu_qos_val)
pm_qos_add_request(&ourport->s3c24xx_uart_cpu_qos,
PM_QOS_CLUSTER1_FREQ_MIN, 0);
}
#endif
if (of_get_property(pdev->dev.of_node, "samsung,in-band-wakeup", NULL))
ourport->in_band_wakeup = 1;
else
ourport->in_band_wakeup = 0;
if (of_get_property(pdev->dev.of_node, "samsung,uart-logging", NULL))
ourport->uart_logging = 1;
else
ourport->uart_logging = 0;
if (of_find_property(pdev->dev.of_node, "samsung,use-default-irq", NULL))
ourport->use_default_irq =1;
else
ourport->use_default_irq =0;
ret = s3c24xx_serial_init_port(ourport, pdev);
if (ret < 0)
return ret;
if (ourport->uart_logging == 1) {
/* Allocate memory for UART logging */
ourport->uart_local_buf.buffer = kzalloc(LOG_BUFFER_SIZE, GFP_KERNEL);
if (!ourport->uart_local_buf.buffer)
dev_err(&pdev->dev, "could not allocate buffer for UART logging\n");
ourport->uart_local_buf.size = LOG_BUFFER_SIZE;
ourport->uart_local_buf.index = 0;
#ifdef BT_UART_TRACE
if (port_index == BLUETOOTH_UART_PORT_LINE) {
struct proc_dir_entry *ent;
bluetooth_dir = proc_mkdir("bluetooth", NULL);
if (bluetooth_dir == NULL) {
pr_err("Unable to create /proc/bluetooth directory\n");
return -ENOMEM;
}
bt_log_dir = proc_mkdir("uart", bluetooth_dir);
if (bt_log_dir == NULL) {
pr_err("Unable to create /proc/%s directory\n", PROC_DIR);
return -ENOMEM;
}
ent = proc_create("log", 0440, bt_log_dir, &proc_fops_btlog);
if (ent == NULL) {
pr_err("Unable to create /proc/%s/log entry\n", PROC_DIR);
return -ENOMEM;
}
}
#endif
#ifdef SERIAL_UART_TRACE
if (port_index == SERIAL_UART_PORT_LINE) {
struct proc_dir_entry *uent;
serial_dir = proc_mkdir("serial", NULL);
if (serial_dir == NULL) {
pr_err("Unable to create /proc/serial directory\n");
return -ENOMEM;
}
serial_log_dir = proc_mkdir("uart", serial_dir);
if (serial_log_dir == NULL) {
pr_err("Unable to create /proc/%s directory\n", PROC_SERIAL_DIR);
return -ENOMEM;
}
uent = proc_create("log", 0444, serial_log_dir, &proc_fops_serial_log);
if (uent == NULL) {
pr_err("Unable to create /proc/%s/log entry\n", PROC_SERIAL_DIR);
return -ENOMEM;
}
}
#endif
}
dbg("%s: adding port\n", __func__);
uart_add_one_port(&s3c24xx_uart_drv, &ourport->port);
platform_set_drvdata(pdev, &ourport->port);
/*
* Deactivate the clock enabled in s3c24xx_serial_init_port here,
* so that a potential re-enablement through the pm-callback overlaps
* and keeps the clock enabled in this case.
*/
uart_clock_disable(ourport);
#ifdef CONFIG_SAMSUNG_CLOCK
ret = device_create_file(&pdev->dev, &dev_attr_clock_source);
if (ret < 0)
dev_err(&pdev->dev, "failed to add clock source attr.\n");
#endif
list_add_tail(&ourport->node, &drvdata_list);
ret = device_create_file(&pdev->dev, &dev_attr_uart_dbg);
if (ret < 0)
dev_err(&pdev->dev, "failed to create sysfs file.\n");
ret = device_create_file(&pdev->dev, &dev_attr_error_cnt);
if (ret < 0)
dev_err(&pdev->dev, "failed to create sysfs file.\n");
ourport->dbg_mode = 0;
return 0;
}
static int s3c24xx_serial_remove(struct platform_device *dev)
{
struct uart_port *port = s3c24xx_dev_to_port(&dev->dev);
#ifdef CONFIG_PM_DEVFREQ
struct s3c24xx_uart_port *ourport = to_ourport(port);
if (ourport->mif_qos_val && ourport->qos_timeout)
pm_qos_remove_request(&ourport->s3c24xx_uart_mif_qos);
if (ourport->cpu_qos_val && ourport->qos_timeout)
pm_qos_remove_request(&ourport->s3c24xx_uart_cpu_qos);
#endif
if (port) {
device_remove_file(&dev->dev, &dev_attr_error_cnt);
#ifdef CONFIG_SAMSUNG_CLOCK
device_remove_file(&dev->dev, &dev_attr_clock_source);
#endif
if (ourport->uart_logging == 1) {
kfree(ourport->uart_local_buf.buffer);
}
uart_remove_one_port(&s3c24xx_uart_drv, port);
}
uart_unregister_driver(&s3c24xx_uart_drv);
return 0;
}
/* UART power management code */
#ifdef CONFIG_PM_SLEEP
static int s3c24xx_serial_suspend(struct device *dev)
{
struct uart_port *port = s3c24xx_dev_to_port(dev);
struct s3c24xx_uart_port *ourport = to_ourport(port);
#ifdef CONFIG_SERIAL_SAMSUNG_HWACG
unsigned int ucon;
#endif
dev_err(dev, "%s %d\n", __func__, __LINE__);
if (port) {
/*
* If rts line must be protected while suspending
* we change the gpio pad as output high
*/
if (ourport->rts_control)
change_uart_gpio(RTS_PINCTRL, ourport);
udelay(300);//delay for sfr update
s3c24xx_serial_rx_fifo_wait();
uart_suspend_port(&s3c24xx_uart_drv, port);
#ifdef CONFIG_SERIAL_SAMSUNG_HWACG
uart_clock_enable(ourport);
/* disable Tx, Rx mode bit for suspend in case of HWACG */
ucon = rd_regl(port, S3C2410_UCON);
ucon &= ~(S3C2410_UCON_RXIRQMODE | S3C2410_UCON_TXIRQMODE);
wr_regl(port, S3C2410_UCON, ucon);
exynos_usi_stop(port);
uart_clock_disable(ourport);
rx_enabled(port) = 0;
tx_enabled(port) = 0;
#endif
if (ourport->dbg_mode & UART_DBG_MODE)
dev_err(dev, "UART suspend notification for tty framework.\n");
}
return 0;
}
static int s3c24xx_serial_prepare(struct device *dev)
{
struct uart_port *port = s3c24xx_dev_to_port(dev);
struct s3c24xx_uart_port *ourport = to_ourport(port);
if (ourport->port.line == BLUETOOTH_UART_PORT_LINE) {
dev_info(&ourport->pdev->dev, "PREPARE : Turn on BT wake_peer\n");
ourport->wake_peer_en = 1;
if (ourport->wake_peer_pended) {
ourport->wake_peer_pended = 0;
s3c24xx_serial_wake_peer(&ourport->port);
}
}
return 0;
}
static int s3c24xx_serial_resume(struct device *dev)
{
struct uart_port *port = s3c24xx_dev_to_port(dev);
struct s3c24xx_uart_port *ourport = to_ourport(port);
if (port) {
clk_prepare_enable(ourport->clk);
if (!IS_ERR(ourport->baudclk))
clk_prepare_enable(ourport->baudclk);
s3c24xx_serial_resetport(port, s3c24xx_port_to_cfg(port));
if (!IS_ERR(ourport->baudclk))
clk_disable_unprepare(ourport->baudclk);
clk_disable_unprepare(ourport->clk);
uart_resume_port(&s3c24xx_uart_drv, port);
if (ourport->rts_control)
change_uart_gpio(DEFAULT_PINCTRL, ourport);
if (ourport->dbg_mode & UART_DBG_MODE)
dev_err(dev, "UART resume notification for tty framework.\n");
}
return 0;
}
static int s3c24xx_serial_resume_noirq(struct device *dev)
{
struct uart_port *port = s3c24xx_dev_to_port(dev);
struct s3c24xx_uart_port *ourport = to_ourport(port);
if (port) {
/* restore IRQ mask */
if (s3c24xx_serial_has_interrupt_mask(port)) {
unsigned int uintm = 0xf;
if (tx_enabled(port))
uintm &= ~S3C64XX_UINTM_TXD_MSK;
if (rx_enabled(port))
uintm &= ~S3C64XX_UINTM_RXD_MSK;
clk_prepare_enable(ourport->clk);
if (!IS_ERR(ourport->baudclk))
clk_prepare_enable(ourport->baudclk);
wr_regl(port, S3C64XX_UINTM, uintm);
if (!IS_ERR(ourport->baudclk))
clk_disable_unprepare(ourport->baudclk);
clk_disable_unprepare(ourport->clk);
}
}
return 0;
}
static const struct dev_pm_ops s3c24xx_serial_pm_ops = {
.suspend = s3c24xx_serial_suspend,
.resume = s3c24xx_serial_resume,
.resume_noirq = s3c24xx_serial_resume_noirq,
.prepare = s3c24xx_serial_prepare,
};
#define SERIAL_SAMSUNG_PM_OPS (&s3c24xx_serial_pm_ops)
#else /* !CONFIG_PM_SLEEP */
#define SERIAL_SAMSUNG_PM_OPS NULL
#endif /* CONFIG_PM_SLEEP */
/* Console code */
#ifdef CONFIG_SERIAL_SAMSUNG_CONSOLE
static struct uart_port *cons_uart;
static int
s3c24xx_serial_console_txrdy(struct uart_port *port, unsigned int ufcon)
{
struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port);
unsigned long ufstat, utrstat;
if (ufcon & S3C2410_UFCON_FIFOMODE) {
/* fifo mode - check amount of data in fifo registers... */
ufstat = rd_regl(port, S3C2410_UFSTAT);
return (ufstat & info->tx_fifofull) ? 0 : 1;
}
/* in non-fifo mode, we go and use the tx buffer empty */
utrstat = rd_regl(port, S3C2410_UTRSTAT);
return (utrstat & S3C2410_UTRSTAT_TXE) ? 1 : 0;
}
static bool
s3c24xx_port_configured(unsigned int ucon)
{
/* consider the serial port configured if the tx/rx mode set */
return (ucon & 0xf) != 0;
}
#ifdef CONFIG_CONSOLE_POLL
/*
* Console polling routines for writing and reading from the uart while
* in an interrupt or debug context.
*/
static int s3c24xx_serial_get_poll_char(struct uart_port *port)
{
struct s3c24xx_uart_port *ourport = to_ourport(port);
unsigned int ufstat;
ufstat = rd_regl(port, S3C2410_UFSTAT);
if (s3c24xx_serial_rx_fifocnt(ourport, ufstat) == 0)
return NO_POLL_CHAR;
return rd_regb(port, S3C2410_URXH);
}
static void s3c24xx_serial_put_poll_char(struct uart_port *port,
unsigned char c)
{
unsigned int ufcon = rd_regl(port, S3C2410_UFCON);
unsigned int ucon = rd_regl(port, S3C2410_UCON);
/* not possible to xmit on unconfigured port */
if (!s3c24xx_port_configured(ucon))
return;
while (!s3c24xx_serial_console_txrdy(port, ufcon))
cpu_relax();
wr_regb(port, S3C2410_UTXH, c);
}
#endif /* CONFIG_CONSOLE_POLL */
static void
s3c24xx_serial_console_putchar(struct uart_port *port, int ch)
{
unsigned int ufcon = rd_regl(port, S3C2410_UFCON);
while (!s3c24xx_serial_console_txrdy(port, ufcon))
cpu_relax();
wr_regb(port, S3C2410_UTXH, ch);
}
static void
s3c24xx_serial_console_write(struct console *co, const char *s,
unsigned int count)
{
unsigned int ucon = rd_regl(cons_uart, S3C2410_UCON);
/* not possible to xmit on unconfigured port */
if (!s3c24xx_port_configured(ucon))
return;
uart_console_write(cons_uart, s, count, s3c24xx_serial_console_putchar);
}
static void __init
s3c24xx_serial_get_options(struct uart_port *port, int *baud,
int *parity, int *bits)
{
struct s3c24xx_uart_port *ourport = to_ourport(port);
unsigned int ulcon;
unsigned int ucon;
unsigned int ubrdiv;
unsigned long rate;
int ret;
ulcon = rd_regl(port, S3C2410_ULCON);
ucon = rd_regl(port, S3C2410_UCON);
ubrdiv = rd_regl(port, S3C2410_UBRDIV);
dbg("s3c24xx_serial_get_options: port=%p\n"
"registers: ulcon=%08x, ucon=%08x, ubdriv=%08x\n",
port, ulcon, ucon, ubrdiv);
if (s3c24xx_port_configured(ucon)) {
switch (ulcon & S3C2410_LCON_CSMASK) {
case S3C2410_LCON_CS5:
*bits = 5;
break;
case S3C2410_LCON_CS6:
*bits = 6;
break;
case S3C2410_LCON_CS7:
*bits = 7;
break;
case S3C2410_LCON_CS8:
default:
*bits = 8;
break;
}
switch (ulcon & S3C2410_LCON_PMASK) {
case S3C2410_LCON_PEVEN:
*parity = 'e';
break;
case S3C2410_LCON_PODD:
*parity = 'o';
break;
case S3C2410_LCON_PNONE:
default:
*parity = 'n';
}
/* now calculate the baud rate */
rate = clk_get_rate(ourport->clk);
if (ourport->src_clk_rate && rate != ourport->src_clk_rate)
{
ret = clk_set_rate(ourport->clk, ourport->src_clk_rate);
if (ret < 0)
dev_err(&ourport->pdev->dev, "UART clk set failed\n");
rate = clk_get_rate(ourport->clk);
}
*baud = rate / (16 * (ubrdiv + 1));
dbg("calculated baud %d\n", *baud);
}
}
static int __init
s3c24xx_serial_console_setup(struct console *co, char *options)
{
struct uart_port *port;
int baud = 9600;
int bits = 8;
int parity = 'n';
int flow = 'n';
dbg("s3c24xx_serial_console_setup: co=%p (%d), %s\n",
co, co->index, options);
/* is this a valid port */
if (co->index == -1 || co->index >= CONFIG_SERIAL_SAMSUNG_UARTS)
co->index = 0;
port = &s3c24xx_serial_ports[co->index].port;
/* is the port configured? */
if (port->mapbase == 0x0)
return -ENODEV;
cons_uart = port;
dbg("s3c24xx_serial_console_setup: port=%p (%d)\n", port, co->index);
/*
* Check whether an invalid uart number has been specified, and
* if so, search for the first available port that does have
* console support.
*/
if (options)
uart_parse_options(options, &baud, &parity, &bits, &flow);
else
s3c24xx_serial_get_options(port, &baud, &parity, &bits);
dbg("s3c24xx_serial_console_setup: baud %d\n", baud);
return uart_set_options(port, co, baud, parity, bits, flow);
}
static struct console s3c24xx_serial_console = {
.name = S3C24XX_SERIAL_NAME,
.device = uart_console_device,
.flags = CON_PRINTBUFFER,
.index = -1,
.write = s3c24xx_serial_console_write,
.setup = s3c24xx_serial_console_setup,
.data = &s3c24xx_uart_drv,
};
#endif /* CONFIG_SERIAL_SAMSUNG_CONSOLE */
#ifdef CONFIG_CPU_S3C2410
static struct s3c24xx_serial_drv_data s3c2410_serial_drv_data = {
.info = &(struct s3c24xx_uart_info) {
.name = "Samsung S3C2410 UART",
.type = PORT_S3C2410,
.fifosize = 16,
.rx_fifomask = S3C2410_UFSTAT_RXMASK,
.rx_fifoshift = S3C2410_UFSTAT_RXSHIFT,
.rx_fifofull = S3C2410_UFSTAT_RXFULL,
.tx_fifofull = S3C2410_UFSTAT_TXFULL,
.tx_fifomask = S3C2410_UFSTAT_TXMASK,
.tx_fifoshift = S3C2410_UFSTAT_TXSHIFT,
.def_clk_sel = S3C2410_UCON_CLKSEL0,
.num_clks = 2,
.clksel_mask = S3C2410_UCON_CLKMASK,
.clksel_shift = S3C2410_UCON_CLKSHIFT,
},
.def_cfg = &(struct s3c2410_uartcfg) {
.ucon = S3C2410_UCON_DEFAULT,
.ufcon = S3C2410_UFCON_DEFAULT,
},
};
#define S3C2410_SERIAL_DRV_DATA ((kernel_ulong_t)&s3c2410_serial_drv_data)
#else
#define S3C2410_SERIAL_DRV_DATA (kernel_ulong_t)NULL
#endif
#ifdef CONFIG_CPU_S3C2412
static struct s3c24xx_serial_drv_data s3c2412_serial_drv_data = {
.info = &(struct s3c24xx_uart_info) {
.name = "Samsung S3C2412 UART",
.type = PORT_S3C2412,
.fifosize = 64,
.has_divslot = 1,
.rx_fifomask = S3C2440_UFSTAT_RXMASK,
.rx_fifoshift = S3C2440_UFSTAT_RXSHIFT,
.rx_fifofull = S3C2440_UFSTAT_RXFULL,
.tx_fifofull = S3C2440_UFSTAT_TXFULL,
.tx_fifomask = S3C2440_UFSTAT_TXMASK,
.tx_fifoshift = S3C2440_UFSTAT_TXSHIFT,
.def_clk_sel = S3C2410_UCON_CLKSEL2,
.num_clks = 4,
.clksel_mask = S3C2412_UCON_CLKMASK,
.clksel_shift = S3C2412_UCON_CLKSHIFT,
},
.def_cfg = &(struct s3c2410_uartcfg) {
.ucon = S3C2410_UCON_DEFAULT,
.ufcon = S3C2410_UFCON_DEFAULT,
},
};
#define S3C2412_SERIAL_DRV_DATA ((kernel_ulong_t)&s3c2412_serial_drv_data)
#else
#define S3C2412_SERIAL_DRV_DATA (kernel_ulong_t)NULL
#endif
#if defined(CONFIG_CPU_S3C2440) || defined(CONFIG_CPU_S3C2416) || \
defined(CONFIG_CPU_S3C2443) || defined(CONFIG_CPU_S3C2442)
static struct s3c24xx_serial_drv_data s3c2440_serial_drv_data = {
.info = &(struct s3c24xx_uart_info) {
.name = "Samsung S3C2440 UART",
.type = PORT_S3C2440,
.fifosize = 64,
.has_divslot = 1,
.rx_fifomask = S3C2440_UFSTAT_RXMASK,
.rx_fifoshift = S3C2440_UFSTAT_RXSHIFT,
.rx_fifofull = S3C2440_UFSTAT_RXFULL,
.tx_fifofull = S3C2440_UFSTAT_TXFULL,
.tx_fifomask = S3C2440_UFSTAT_TXMASK,
.tx_fifoshift = S3C2440_UFSTAT_TXSHIFT,
.def_clk_sel = S3C2410_UCON_CLKSEL2,
.num_clks = 4,
.clksel_mask = S3C2412_UCON_CLKMASK,
.clksel_shift = S3C2412_UCON_CLKSHIFT,
},
.def_cfg = &(struct s3c2410_uartcfg) {
.ucon = S3C2410_UCON_DEFAULT,
.ufcon = S3C2410_UFCON_DEFAULT,
},
};
#define S3C2440_SERIAL_DRV_DATA ((kernel_ulong_t)&s3c2440_serial_drv_data)
#else
#define S3C2440_SERIAL_DRV_DATA (kernel_ulong_t)NULL
#endif
#if defined(CONFIG_CPU_S3C6400) || defined(CONFIG_CPU_S3C6410)
static struct s3c24xx_serial_drv_data s3c6400_serial_drv_data = {
.info = &(struct s3c24xx_uart_info) {
.name = "Samsung S3C6400 UART",
.type = PORT_S3C6400,
.fifosize = 64,
.has_divslot = 1,
.rx_fifomask = S3C2440_UFSTAT_RXMASK,
.rx_fifoshift = S3C2440_UFSTAT_RXSHIFT,
.rx_fifofull = S3C2440_UFSTAT_RXFULL,
.tx_fifofull = S3C2440_UFSTAT_TXFULL,
.tx_fifomask = S3C2440_UFSTAT_TXMASK,
.tx_fifoshift = S3C2440_UFSTAT_TXSHIFT,
.def_clk_sel = S3C2410_UCON_CLKSEL2,
.num_clks = 4,
.clksel_mask = S3C6400_UCON_CLKMASK,
.clksel_shift = S3C6400_UCON_CLKSHIFT,
},
.def_cfg = &(struct s3c2410_uartcfg) {
.ucon = S3C2410_UCON_DEFAULT,
.ufcon = S3C2410_UFCON_DEFAULT,
},
};
#define S3C6400_SERIAL_DRV_DATA ((kernel_ulong_t)&s3c6400_serial_drv_data)
#else
#define S3C6400_SERIAL_DRV_DATA (kernel_ulong_t)NULL
#endif
#ifdef CONFIG_CPU_S5PV210
static struct s3c24xx_serial_drv_data s5pv210_serial_drv_data = {
.info = &(struct s3c24xx_uart_info) {
.name = "Samsung S5PV210 UART",
.type = PORT_S3C6400,
.has_divslot = 1,
.rx_fifomask = S5PV210_UFSTAT_RXMASK,
.rx_fifoshift = S5PV210_UFSTAT_RXSHIFT,
.rx_fifofull = S5PV210_UFSTAT_RXFULL,
.tx_fifofull = S5PV210_UFSTAT_TXFULL,
.tx_fifomask = S5PV210_UFSTAT_TXMASK,
.tx_fifoshift = S5PV210_UFSTAT_TXSHIFT,
.def_clk_sel = S3C2410_UCON_CLKSEL0,
.num_clks = 2,
.clksel_mask = S5PV210_UCON_CLKMASK,
.clksel_shift = S5PV210_UCON_CLKSHIFT,
},
.def_cfg = &(struct s3c2410_uartcfg) {
.ucon = S5PV210_UCON_DEFAULT,
.ufcon = S5PV210_UFCON_DEFAULT,
},
.fifosize = { 256, 64, 16, 16 },
};
#define S5PV210_SERIAL_DRV_DATA ((kernel_ulong_t)&s5pv210_serial_drv_data)
#else
#define S5PV210_SERIAL_DRV_DATA (kernel_ulong_t)NULL
#endif
#if defined(CONFIG_ARCH_EXYNOS)
#define EXYNOS_COMMON_SERIAL_DRV_DATA \
.info = &(struct s3c24xx_uart_info) { \
.name = "Samsung Exynos UART", \
.type = PORT_S3C6400, \
.has_divslot = 1, \
.rx_fifomask = S5PV210_UFSTAT_RXMASK, \
.rx_fifoshift = S5PV210_UFSTAT_RXSHIFT, \
.rx_fifofull = S5PV210_UFSTAT_RXFULL, \
.tx_fifofull = S5PV210_UFSTAT_TXFULL, \
.tx_fifomask = S5PV210_UFSTAT_TXMASK, \
.tx_fifoshift = S5PV210_UFSTAT_TXSHIFT, \
.rts_trig_shift = S5PV210_UMCON_RTSTRIG_SHIFT, \
.def_clk_sel = S3C2410_UCON_CLKSEL0, \
.num_clks = 1, \
.clksel_mask = 0, \
.clksel_shift = 0, \
}, \
.def_cfg = &(struct s3c2410_uartcfg) { \
.ucon = S5PV210_UCON_DEFAULT, \
.ufcon = S5PV210_UFCON_DEFAULT, \
.has_fracval = 1, \
} \
static struct s3c24xx_serial_drv_data exynos4210_serial_drv_data = {
EXYNOS_COMMON_SERIAL_DRV_DATA,
.fifosize = { 256, 64, 16, 16 },
};
static struct s3c24xx_serial_drv_data exynos_serial_drv_data = {
EXYNOS_COMMON_SERIAL_DRV_DATA,
.fifosize = { 0, },
};
#define EXYNOS4210_SERIAL_DRV_DATA ((kernel_ulong_t)&exynos4210_serial_drv_data)
#define EXYNOS_SERIAL_DRV_DATA ((kernel_ulong_t)&exynos_serial_drv_data)
#else
#define EXYNOS4210_SERIAL_DRV_DATA (kernel_ulong_t)NULL
#define EXYNOS_SERIAL_DRV_DATA (kernel_ulong_t)NULL
#endif
static const struct platform_device_id s3c24xx_serial_driver_ids[] = {
{
.name = "s3c2410-uart",
.driver_data = S3C2410_SERIAL_DRV_DATA,
}, {
.name = "s3c2412-uart",
.driver_data = S3C2412_SERIAL_DRV_DATA,
}, {
.name = "s3c2440-uart",
.driver_data = S3C2440_SERIAL_DRV_DATA,
}, {
.name = "s3c6400-uart",
.driver_data = S3C6400_SERIAL_DRV_DATA,
}, {
.name = "s5pv210-uart",
.driver_data = S5PV210_SERIAL_DRV_DATA,
}, {
.name = "exynos4210-uart",
.driver_data = EXYNOS4210_SERIAL_DRV_DATA,
}, {
.name = "exynos-uart",
.driver_data = EXYNOS_SERIAL_DRV_DATA,
},
{ },
};
MODULE_DEVICE_TABLE(platform, s3c24xx_serial_driver_ids);
#ifdef CONFIG_OF
static const struct of_device_id s3c24xx_uart_dt_match[] = {
{ .compatible = "samsung,s3c2410-uart",
.data = (void *)S3C2410_SERIAL_DRV_DATA },
{ .compatible = "samsung,s3c2412-uart",
.data = (void *)S3C2412_SERIAL_DRV_DATA },
{ .compatible = "samsung,s3c2440-uart",
.data = (void *)S3C2440_SERIAL_DRV_DATA },
{ .compatible = "samsung,s3c6400-uart",
.data = (void *)S3C6400_SERIAL_DRV_DATA },
{ .compatible = "samsung,s5pv210-uart",
.data = (void *)S5PV210_SERIAL_DRV_DATA },
{ .compatible = "samsung,exynos4210-uart",
.data = (void *)EXYNOS4210_SERIAL_DRV_DATA },
{ .compatible = "samsung,exynos-uart",
.data = (void *)EXYNOS_SERIAL_DRV_DATA },
{},
};
MODULE_DEVICE_TABLE(of, s3c24xx_uart_dt_match);
#endif
static struct platform_driver samsung_serial_driver = {
.probe = s3c24xx_serial_probe,
.remove = s3c24xx_serial_remove,
.id_table = s3c24xx_serial_driver_ids,
.driver = {
.name = "samsung-uart",
.pm = SERIAL_SAMSUNG_PM_OPS,
.of_match_table = of_match_ptr(s3c24xx_uart_dt_match),
},
};
/* module initialisation code */
static int __init s3c24xx_serial_modinit(void)
{
int ret;
ret = uart_register_driver(&s3c24xx_uart_drv);
if (ret < 0) {
pr_err("Failed to register Samsung UART driver\n");
return ret;
}
#ifdef CONFIG_CPU_IDLE
exynos_pm_register_notifier(&s3c24xx_serial_notifier_block);
#endif
register_pm_notifier(&exynos_s3c64xx_nb);
return platform_driver_register(&samsung_serial_driver);
}
static void __exit s3c24xx_serial_modexit(void)
{
platform_driver_unregister(&samsung_serial_driver);
uart_unregister_driver(&s3c24xx_uart_drv);
}
module_init(s3c24xx_serial_modinit);
module_exit(s3c24xx_serial_modexit);
#ifdef CONFIG_SERIAL_SAMSUNG_CONSOLE
/*
* Early console.
*/
struct samsung_early_console_data {
u32 txfull_mask;
};
static void samsung_early_busyuart(struct uart_port *port)
{
while (!(readl(port->membase + S3C2410_UTRSTAT) & S3C2410_UTRSTAT_TXFE))
;
}
static void samsung_early_busyuart_fifo(struct uart_port *port)
{
struct samsung_early_console_data *data = port->private_data;
while (readl(port->membase + S3C2410_UFSTAT) & data->txfull_mask)
;
}
static void samsung_early_putc(struct uart_port *port, int c)
{
if (readl(port->membase + S3C2410_UFCON) & S3C2410_UFCON_FIFOMODE)
samsung_early_busyuart_fifo(port);
else
samsung_early_busyuart(port);
writeb(c, port->membase + S3C2410_UTXH);
}
static void samsung_early_write(struct console *con, const char *s, unsigned n)
{
struct earlycon_device *dev = con->data;
uart_console_write(&dev->port, s, n, samsung_early_putc);
}
static int __init samsung_early_console_setup(struct earlycon_device *device,
const char *opt)
{
if (!device->port.membase)
return -ENODEV;
device->con->write = samsung_early_write;
return 0;
}
/* S3C2410 */
static struct samsung_early_console_data s3c2410_early_console_data = {
.txfull_mask = S3C2410_UFSTAT_TXFULL,
};
static int __init s3c2410_early_console_setup(struct earlycon_device *device,
const char *opt)
{
device->port.private_data = &s3c2410_early_console_data;
return samsung_early_console_setup(device, opt);
}
OF_EARLYCON_DECLARE(s3c2410, "samsung,s3c2410-uart",
s3c2410_early_console_setup);
/* S3C2412, S3C2440, S3C64xx */
static struct samsung_early_console_data s3c2440_early_console_data = {
.txfull_mask = S3C2440_UFSTAT_TXFULL,
};
static int __init s3c2440_early_console_setup(struct earlycon_device *device,
const char *opt)
{
device->port.private_data = &s3c2440_early_console_data;
return samsung_early_console_setup(device, opt);
}
OF_EARLYCON_DECLARE(s3c2412, "samsung,s3c2412-uart",
s3c2440_early_console_setup);
OF_EARLYCON_DECLARE(s3c2440, "samsung,s3c2440-uart",
s3c2440_early_console_setup);
OF_EARLYCON_DECLARE(s3c6400, "samsung,s3c6400-uart",
s3c2440_early_console_setup);
/* S5PV210, EXYNOS */
static struct samsung_early_console_data s5pv210_early_console_data = {
.txfull_mask = S5PV210_UFSTAT_TXFULL,
};
static int __init s5pv210_early_console_setup(struct earlycon_device *device,
const char *opt)
{
device->port.private_data = &s5pv210_early_console_data;
return samsung_early_console_setup(device, opt);
}
OF_EARLYCON_DECLARE(s5pv210, "samsung,s5pv210-uart",
s5pv210_early_console_setup);
OF_EARLYCON_DECLARE(exynos4210, "samsung,exynos4210-uart",
s5pv210_early_console_setup);
#endif
MODULE_ALIAS("platform:samsung-uart");
MODULE_DESCRIPTION("Samsung SoC Serial port driver");
MODULE_AUTHOR("Ben Dooks <ben@simtec.co.uk>");
MODULE_LICENSE("GPL v2");