| /* |
| * Allwinner sun4i USB phy driver |
| * |
| * Copyright (C) 2014-2015 Hans de Goede <hdegoede@redhat.com> |
| * |
| * Based on code from |
| * Allwinner Technology Co., Ltd. <www.allwinnertech.com> |
| * |
| * Modelled after: Samsung S5P/EXYNOS SoC series MIPI CSIS/DSIM DPHY driver |
| * Copyright (C) 2013 Samsung Electronics Co., Ltd. |
| * Author: Sylwester Nawrocki <s.nawrocki@samsung.com> |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation; either version 2 of the License, or |
| * (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| */ |
| |
| #include <linux/clk.h> |
| #include <linux/delay.h> |
| #include <linux/err.h> |
| #include <linux/extcon.h> |
| #include <linux/io.h> |
| #include <linux/interrupt.h> |
| #include <linux/kernel.h> |
| #include <linux/module.h> |
| #include <linux/mutex.h> |
| #include <linux/of.h> |
| #include <linux/of_address.h> |
| #include <linux/of_device.h> |
| #include <linux/of_gpio.h> |
| #include <linux/phy/phy.h> |
| #include <linux/phy/phy-sun4i-usb.h> |
| #include <linux/platform_device.h> |
| #include <linux/power_supply.h> |
| #include <linux/regulator/consumer.h> |
| #include <linux/reset.h> |
| #include <linux/spinlock.h> |
| #include <linux/usb/of.h> |
| #include <linux/workqueue.h> |
| |
| #define REG_ISCR 0x00 |
| #define REG_PHYCTL_A10 0x04 |
| #define REG_PHYBIST 0x08 |
| #define REG_PHYTUNE 0x0c |
| #define REG_PHYCTL_A33 0x10 |
| #define REG_PHY_OTGCTL 0x20 |
| |
| #define REG_PMU_UNK1 0x10 |
| |
| #define PHYCTL_DATA BIT(7) |
| |
| #define OTGCTL_ROUTE_MUSB BIT(0) |
| |
| #define SUNXI_AHB_ICHR8_EN BIT(10) |
| #define SUNXI_AHB_INCR4_BURST_EN BIT(9) |
| #define SUNXI_AHB_INCRX_ALIGN_EN BIT(8) |
| #define SUNXI_ULPI_BYPASS_EN BIT(0) |
| |
| /* ISCR, Interface Status and Control bits */ |
| #define ISCR_ID_PULLUP_EN (1 << 17) |
| #define ISCR_DPDM_PULLUP_EN (1 << 16) |
| /* sunxi has the phy id/vbus pins not connected, so we use the force bits */ |
| #define ISCR_FORCE_ID_MASK (3 << 14) |
| #define ISCR_FORCE_ID_LOW (2 << 14) |
| #define ISCR_FORCE_ID_HIGH (3 << 14) |
| #define ISCR_FORCE_VBUS_MASK (3 << 12) |
| #define ISCR_FORCE_VBUS_LOW (2 << 12) |
| #define ISCR_FORCE_VBUS_HIGH (3 << 12) |
| |
| /* Common Control Bits for Both PHYs */ |
| #define PHY_PLL_BW 0x03 |
| #define PHY_RES45_CAL_EN 0x0c |
| |
| /* Private Control Bits for Each PHY */ |
| #define PHY_TX_AMPLITUDE_TUNE 0x20 |
| #define PHY_TX_SLEWRATE_TUNE 0x22 |
| #define PHY_VBUSVALID_TH_SEL 0x25 |
| #define PHY_PULLUP_RES_SEL 0x27 |
| #define PHY_OTG_FUNC_EN 0x28 |
| #define PHY_VBUS_DET_EN 0x29 |
| #define PHY_DISCON_TH_SEL 0x2a |
| #define PHY_SQUELCH_DETECT 0x3c |
| |
| /* A83T specific control bits for PHY0 */ |
| #define PHY_CTL_VBUSVLDEXT BIT(5) |
| #define PHY_CTL_SIDDQ BIT(3) |
| |
| /* A83T specific control bits for PHY2 HSIC */ |
| #define SUNXI_EHCI_HS_FORCE BIT(20) |
| #define SUNXI_HSIC_CONNECT_DET BIT(17) |
| #define SUNXI_HSIC_CONNECT_INT BIT(16) |
| #define SUNXI_HSIC BIT(1) |
| |
| #define MAX_PHYS 4 |
| |
| /* |
| * Note do not raise the debounce time, we must report Vusb high within 100ms |
| * otherwise we get Vbus errors |
| */ |
| #define DEBOUNCE_TIME msecs_to_jiffies(50) |
| #define POLL_TIME msecs_to_jiffies(250) |
| |
| enum sun4i_usb_phy_type { |
| sun4i_a10_phy, |
| sun6i_a31_phy, |
| sun8i_a33_phy, |
| sun8i_a83t_phy, |
| sun8i_h3_phy, |
| sun8i_v3s_phy, |
| sun50i_a64_phy, |
| }; |
| |
| struct sun4i_usb_phy_cfg { |
| int num_phys; |
| int hsic_index; |
| enum sun4i_usb_phy_type type; |
| u32 disc_thresh; |
| u8 phyctl_offset; |
| bool dedicated_clocks; |
| bool enable_pmu_unk1; |
| bool phy0_dual_route; |
| }; |
| |
| struct sun4i_usb_phy_data { |
| void __iomem *base; |
| const struct sun4i_usb_phy_cfg *cfg; |
| enum usb_dr_mode dr_mode; |
| spinlock_t reg_lock; /* guard access to phyctl reg */ |
| struct sun4i_usb_phy { |
| struct phy *phy; |
| void __iomem *pmu; |
| struct regulator *vbus; |
| struct reset_control *reset; |
| struct clk *clk; |
| struct clk *clk2; |
| bool regulator_on; |
| int index; |
| } phys[MAX_PHYS]; |
| /* phy0 / otg related variables */ |
| struct extcon_dev *extcon; |
| bool phy0_init; |
| struct gpio_desc *id_det_gpio; |
| struct gpio_desc *vbus_det_gpio; |
| struct power_supply *vbus_power_supply; |
| struct notifier_block vbus_power_nb; |
| bool vbus_power_nb_registered; |
| bool force_session_end; |
| int id_det_irq; |
| int vbus_det_irq; |
| int id_det; |
| int vbus_det; |
| struct delayed_work detect; |
| }; |
| |
| #define to_sun4i_usb_phy_data(phy) \ |
| container_of((phy), struct sun4i_usb_phy_data, phys[(phy)->index]) |
| |
| static void sun4i_usb_phy0_update_iscr(struct phy *_phy, u32 clr, u32 set) |
| { |
| struct sun4i_usb_phy *phy = phy_get_drvdata(_phy); |
| struct sun4i_usb_phy_data *data = to_sun4i_usb_phy_data(phy); |
| u32 iscr; |
| |
| iscr = readl(data->base + REG_ISCR); |
| iscr &= ~clr; |
| iscr |= set; |
| writel(iscr, data->base + REG_ISCR); |
| } |
| |
| static void sun4i_usb_phy0_set_id_detect(struct phy *phy, u32 val) |
| { |
| if (val) |
| val = ISCR_FORCE_ID_HIGH; |
| else |
| val = ISCR_FORCE_ID_LOW; |
| |
| sun4i_usb_phy0_update_iscr(phy, ISCR_FORCE_ID_MASK, val); |
| } |
| |
| static void sun4i_usb_phy0_set_vbus_detect(struct phy *phy, u32 val) |
| { |
| if (val) |
| val = ISCR_FORCE_VBUS_HIGH; |
| else |
| val = ISCR_FORCE_VBUS_LOW; |
| |
| sun4i_usb_phy0_update_iscr(phy, ISCR_FORCE_VBUS_MASK, val); |
| } |
| |
| static void sun4i_usb_phy_write(struct sun4i_usb_phy *phy, u32 addr, u32 data, |
| int len) |
| { |
| struct sun4i_usb_phy_data *phy_data = to_sun4i_usb_phy_data(phy); |
| u32 temp, usbc_bit = BIT(phy->index * 2); |
| void __iomem *phyctl = phy_data->base + phy_data->cfg->phyctl_offset; |
| unsigned long flags; |
| int i; |
| |
| spin_lock_irqsave(&phy_data->reg_lock, flags); |
| |
| if (phy_data->cfg->phyctl_offset == REG_PHYCTL_A33) { |
| /* SoCs newer than A33 need us to set phyctl to 0 explicitly */ |
| writel(0, phyctl); |
| } |
| |
| for (i = 0; i < len; i++) { |
| temp = readl(phyctl); |
| |
| /* clear the address portion */ |
| temp &= ~(0xff << 8); |
| |
| /* set the address */ |
| temp |= ((addr + i) << 8); |
| writel(temp, phyctl); |
| |
| /* set the data bit and clear usbc bit*/ |
| temp = readb(phyctl); |
| if (data & 0x1) |
| temp |= PHYCTL_DATA; |
| else |
| temp &= ~PHYCTL_DATA; |
| temp &= ~usbc_bit; |
| writeb(temp, phyctl); |
| |
| /* pulse usbc_bit */ |
| temp = readb(phyctl); |
| temp |= usbc_bit; |
| writeb(temp, phyctl); |
| |
| temp = readb(phyctl); |
| temp &= ~usbc_bit; |
| writeb(temp, phyctl); |
| |
| data >>= 1; |
| } |
| |
| spin_unlock_irqrestore(&phy_data->reg_lock, flags); |
| } |
| |
| static void sun4i_usb_phy_passby(struct sun4i_usb_phy *phy, int enable) |
| { |
| struct sun4i_usb_phy_data *phy_data = to_sun4i_usb_phy_data(phy); |
| u32 bits, reg_value; |
| |
| if (!phy->pmu) |
| return; |
| |
| bits = SUNXI_AHB_ICHR8_EN | SUNXI_AHB_INCR4_BURST_EN | |
| SUNXI_AHB_INCRX_ALIGN_EN | SUNXI_ULPI_BYPASS_EN; |
| |
| /* A83T USB2 is HSIC */ |
| if (phy_data->cfg->type == sun8i_a83t_phy && phy->index == 2) |
| bits |= SUNXI_EHCI_HS_FORCE | SUNXI_HSIC_CONNECT_INT | |
| SUNXI_HSIC; |
| |
| reg_value = readl(phy->pmu); |
| |
| if (enable) |
| reg_value |= bits; |
| else |
| reg_value &= ~bits; |
| |
| writel(reg_value, phy->pmu); |
| } |
| |
| static int sun4i_usb_phy_init(struct phy *_phy) |
| { |
| struct sun4i_usb_phy *phy = phy_get_drvdata(_phy); |
| struct sun4i_usb_phy_data *data = to_sun4i_usb_phy_data(phy); |
| int ret; |
| u32 val; |
| |
| ret = clk_prepare_enable(phy->clk); |
| if (ret) |
| return ret; |
| |
| ret = clk_prepare_enable(phy->clk2); |
| if (ret) { |
| clk_disable_unprepare(phy->clk); |
| return ret; |
| } |
| |
| ret = reset_control_deassert(phy->reset); |
| if (ret) { |
| clk_disable_unprepare(phy->clk2); |
| clk_disable_unprepare(phy->clk); |
| return ret; |
| } |
| |
| if (data->cfg->type == sun8i_a83t_phy) { |
| if (phy->index == 0) { |
| val = readl(data->base + data->cfg->phyctl_offset); |
| val |= PHY_CTL_VBUSVLDEXT; |
| val &= ~PHY_CTL_SIDDQ; |
| writel(val, data->base + data->cfg->phyctl_offset); |
| } |
| } else { |
| if (phy->pmu && data->cfg->enable_pmu_unk1) { |
| val = readl(phy->pmu + REG_PMU_UNK1); |
| writel(val & ~2, phy->pmu + REG_PMU_UNK1); |
| } |
| |
| /* Enable USB 45 Ohm resistor calibration */ |
| if (phy->index == 0) |
| sun4i_usb_phy_write(phy, PHY_RES45_CAL_EN, 0x01, 1); |
| |
| /* Adjust PHY's magnitude and rate */ |
| sun4i_usb_phy_write(phy, PHY_TX_AMPLITUDE_TUNE, 0x14, 5); |
| |
| /* Disconnect threshold adjustment */ |
| sun4i_usb_phy_write(phy, PHY_DISCON_TH_SEL, |
| data->cfg->disc_thresh, 2); |
| } |
| |
| sun4i_usb_phy_passby(phy, 1); |
| |
| if (phy->index == 0) { |
| data->phy0_init = true; |
| |
| /* Enable pull-ups */ |
| sun4i_usb_phy0_update_iscr(_phy, 0, ISCR_DPDM_PULLUP_EN); |
| sun4i_usb_phy0_update_iscr(_phy, 0, ISCR_ID_PULLUP_EN); |
| |
| /* Force ISCR and cable state updates */ |
| data->id_det = -1; |
| data->vbus_det = -1; |
| queue_delayed_work(system_wq, &data->detect, 0); |
| } |
| |
| return 0; |
| } |
| |
| static int sun4i_usb_phy_exit(struct phy *_phy) |
| { |
| struct sun4i_usb_phy *phy = phy_get_drvdata(_phy); |
| struct sun4i_usb_phy_data *data = to_sun4i_usb_phy_data(phy); |
| |
| if (phy->index == 0) { |
| if (data->cfg->type == sun8i_a83t_phy) { |
| void __iomem *phyctl = data->base + |
| data->cfg->phyctl_offset; |
| |
| writel(readl(phyctl) | PHY_CTL_SIDDQ, phyctl); |
| } |
| |
| /* Disable pull-ups */ |
| sun4i_usb_phy0_update_iscr(_phy, ISCR_DPDM_PULLUP_EN, 0); |
| sun4i_usb_phy0_update_iscr(_phy, ISCR_ID_PULLUP_EN, 0); |
| data->phy0_init = false; |
| } |
| |
| sun4i_usb_phy_passby(phy, 0); |
| reset_control_assert(phy->reset); |
| clk_disable_unprepare(phy->clk2); |
| clk_disable_unprepare(phy->clk); |
| |
| return 0; |
| } |
| |
| static int sun4i_usb_phy0_get_id_det(struct sun4i_usb_phy_data *data) |
| { |
| switch (data->dr_mode) { |
| case USB_DR_MODE_OTG: |
| if (data->id_det_gpio) |
| return gpiod_get_value_cansleep(data->id_det_gpio); |
| else |
| return 1; /* Fallback to peripheral mode */ |
| case USB_DR_MODE_HOST: |
| return 0; |
| case USB_DR_MODE_PERIPHERAL: |
| default: |
| return 1; |
| } |
| } |
| |
| static int sun4i_usb_phy0_get_vbus_det(struct sun4i_usb_phy_data *data) |
| { |
| if (data->vbus_det_gpio) |
| return gpiod_get_value_cansleep(data->vbus_det_gpio); |
| |
| if (data->vbus_power_supply) { |
| union power_supply_propval val; |
| int r; |
| |
| r = power_supply_get_property(data->vbus_power_supply, |
| POWER_SUPPLY_PROP_PRESENT, &val); |
| if (r == 0) |
| return val.intval; |
| } |
| |
| /* Fallback: report vbus as high */ |
| return 1; |
| } |
| |
| static bool sun4i_usb_phy0_have_vbus_det(struct sun4i_usb_phy_data *data) |
| { |
| return data->vbus_det_gpio || data->vbus_power_supply; |
| } |
| |
| static bool sun4i_usb_phy0_poll(struct sun4i_usb_phy_data *data) |
| { |
| if ((data->id_det_gpio && data->id_det_irq <= 0) || |
| (data->vbus_det_gpio && data->vbus_det_irq <= 0)) |
| return true; |
| |
| /* |
| * The A31/A23/A33 companion pmics (AXP221/AXP223) do not |
| * generate vbus change interrupts when the board is driving |
| * vbus using the N_VBUSEN pin on the pmic, so we must poll |
| * when using the pmic for vbus-det _and_ we're driving vbus. |
| */ |
| if ((data->cfg->type == sun6i_a31_phy || |
| data->cfg->type == sun8i_a33_phy) && |
| data->vbus_power_supply && data->phys[0].regulator_on) |
| return true; |
| |
| return false; |
| } |
| |
| static int sun4i_usb_phy_power_on(struct phy *_phy) |
| { |
| struct sun4i_usb_phy *phy = phy_get_drvdata(_phy); |
| struct sun4i_usb_phy_data *data = to_sun4i_usb_phy_data(phy); |
| int ret; |
| |
| if (!phy->vbus || phy->regulator_on) |
| return 0; |
| |
| /* For phy0 only turn on Vbus if we don't have an ext. Vbus */ |
| if (phy->index == 0 && sun4i_usb_phy0_have_vbus_det(data) && |
| data->vbus_det) { |
| dev_warn(&_phy->dev, "External vbus detected, not enabling our own vbus\n"); |
| return 0; |
| } |
| |
| ret = regulator_enable(phy->vbus); |
| if (ret) |
| return ret; |
| |
| phy->regulator_on = true; |
| |
| /* We must report Vbus high within OTG_TIME_A_WAIT_VRISE msec. */ |
| if (phy->index == 0 && sun4i_usb_phy0_poll(data)) |
| mod_delayed_work(system_wq, &data->detect, DEBOUNCE_TIME); |
| |
| return 0; |
| } |
| |
| static int sun4i_usb_phy_power_off(struct phy *_phy) |
| { |
| struct sun4i_usb_phy *phy = phy_get_drvdata(_phy); |
| struct sun4i_usb_phy_data *data = to_sun4i_usb_phy_data(phy); |
| |
| if (!phy->vbus || !phy->regulator_on) |
| return 0; |
| |
| regulator_disable(phy->vbus); |
| phy->regulator_on = false; |
| |
| /* |
| * phy0 vbus typically slowly discharges, sometimes this causes the |
| * Vbus gpio to not trigger an edge irq on Vbus off, so force a rescan. |
| */ |
| if (phy->index == 0 && !sun4i_usb_phy0_poll(data)) |
| mod_delayed_work(system_wq, &data->detect, POLL_TIME); |
| |
| return 0; |
| } |
| |
| static int sun4i_usb_phy_set_mode(struct phy *_phy, enum phy_mode mode) |
| { |
| struct sun4i_usb_phy *phy = phy_get_drvdata(_phy); |
| struct sun4i_usb_phy_data *data = to_sun4i_usb_phy_data(phy); |
| int new_mode; |
| |
| if (phy->index != 0) |
| return -EINVAL; |
| |
| switch (mode) { |
| case PHY_MODE_USB_HOST: |
| new_mode = USB_DR_MODE_HOST; |
| break; |
| case PHY_MODE_USB_DEVICE: |
| new_mode = USB_DR_MODE_PERIPHERAL; |
| break; |
| case PHY_MODE_USB_OTG: |
| new_mode = USB_DR_MODE_OTG; |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| if (new_mode != data->dr_mode) { |
| dev_info(&_phy->dev, "Changing dr_mode to %d\n", new_mode); |
| data->dr_mode = new_mode; |
| } |
| |
| data->id_det = -1; /* Force reprocessing of id */ |
| data->force_session_end = true; |
| queue_delayed_work(system_wq, &data->detect, 0); |
| |
| return 0; |
| } |
| |
| void sun4i_usb_phy_set_squelch_detect(struct phy *_phy, bool enabled) |
| { |
| struct sun4i_usb_phy *phy = phy_get_drvdata(_phy); |
| |
| sun4i_usb_phy_write(phy, PHY_SQUELCH_DETECT, enabled ? 0 : 2, 2); |
| } |
| EXPORT_SYMBOL_GPL(sun4i_usb_phy_set_squelch_detect); |
| |
| static const struct phy_ops sun4i_usb_phy_ops = { |
| .init = sun4i_usb_phy_init, |
| .exit = sun4i_usb_phy_exit, |
| .power_on = sun4i_usb_phy_power_on, |
| .power_off = sun4i_usb_phy_power_off, |
| .set_mode = sun4i_usb_phy_set_mode, |
| .owner = THIS_MODULE, |
| }; |
| |
| static void sun4i_usb_phy0_reroute(struct sun4i_usb_phy_data *data, int id_det) |
| { |
| u32 regval; |
| |
| regval = readl(data->base + REG_PHY_OTGCTL); |
| if (id_det == 0) { |
| /* Host mode. Route phy0 to EHCI/OHCI */ |
| regval &= ~OTGCTL_ROUTE_MUSB; |
| } else { |
| /* Peripheral mode. Route phy0 to MUSB */ |
| regval |= OTGCTL_ROUTE_MUSB; |
| } |
| writel(regval, data->base + REG_PHY_OTGCTL); |
| } |
| |
| static void sun4i_usb_phy0_id_vbus_det_scan(struct work_struct *work) |
| { |
| struct sun4i_usb_phy_data *data = |
| container_of(work, struct sun4i_usb_phy_data, detect.work); |
| struct phy *phy0 = data->phys[0].phy; |
| bool force_session_end, id_notify = false, vbus_notify = false; |
| int id_det, vbus_det; |
| |
| if (phy0 == NULL) |
| return; |
| |
| id_det = sun4i_usb_phy0_get_id_det(data); |
| vbus_det = sun4i_usb_phy0_get_vbus_det(data); |
| |
| mutex_lock(&phy0->mutex); |
| |
| if (!data->phy0_init) { |
| mutex_unlock(&phy0->mutex); |
| return; |
| } |
| |
| force_session_end = data->force_session_end; |
| data->force_session_end = false; |
| |
| if (id_det != data->id_det) { |
| /* id-change, force session end if we've no vbus detection */ |
| if (data->dr_mode == USB_DR_MODE_OTG && |
| !sun4i_usb_phy0_have_vbus_det(data)) |
| force_session_end = true; |
| |
| /* When entering host mode (id = 0) force end the session now */ |
| if (force_session_end && id_det == 0) { |
| sun4i_usb_phy0_set_vbus_detect(phy0, 0); |
| msleep(200); |
| sun4i_usb_phy0_set_vbus_detect(phy0, 1); |
| } |
| sun4i_usb_phy0_set_id_detect(phy0, id_det); |
| data->id_det = id_det; |
| id_notify = true; |
| } |
| |
| if (vbus_det != data->vbus_det) { |
| sun4i_usb_phy0_set_vbus_detect(phy0, vbus_det); |
| data->vbus_det = vbus_det; |
| vbus_notify = true; |
| } |
| |
| mutex_unlock(&phy0->mutex); |
| |
| if (id_notify) { |
| extcon_set_state_sync(data->extcon, EXTCON_USB_HOST, |
| !id_det); |
| /* When leaving host mode force end the session here */ |
| if (force_session_end && id_det == 1) { |
| mutex_lock(&phy0->mutex); |
| sun4i_usb_phy0_set_vbus_detect(phy0, 0); |
| msleep(1000); |
| sun4i_usb_phy0_set_vbus_detect(phy0, 1); |
| mutex_unlock(&phy0->mutex); |
| } |
| |
| /* Re-route PHY0 if necessary */ |
| if (data->cfg->phy0_dual_route) |
| sun4i_usb_phy0_reroute(data, id_det); |
| } |
| |
| if (vbus_notify) |
| extcon_set_state_sync(data->extcon, EXTCON_USB, vbus_det); |
| |
| if (sun4i_usb_phy0_poll(data)) |
| queue_delayed_work(system_wq, &data->detect, POLL_TIME); |
| } |
| |
| static irqreturn_t sun4i_usb_phy0_id_vbus_det_irq(int irq, void *dev_id) |
| { |
| struct sun4i_usb_phy_data *data = dev_id; |
| |
| /* vbus or id changed, let the pins settle and then scan them */ |
| mod_delayed_work(system_wq, &data->detect, DEBOUNCE_TIME); |
| |
| return IRQ_HANDLED; |
| } |
| |
| static int sun4i_usb_phy0_vbus_notify(struct notifier_block *nb, |
| unsigned long val, void *v) |
| { |
| struct sun4i_usb_phy_data *data = |
| container_of(nb, struct sun4i_usb_phy_data, vbus_power_nb); |
| struct power_supply *psy = v; |
| |
| /* Properties on the vbus_power_supply changed, scan vbus_det */ |
| if (val == PSY_EVENT_PROP_CHANGED && psy == data->vbus_power_supply) |
| mod_delayed_work(system_wq, &data->detect, DEBOUNCE_TIME); |
| |
| return NOTIFY_OK; |
| } |
| |
| static struct phy *sun4i_usb_phy_xlate(struct device *dev, |
| struct of_phandle_args *args) |
| { |
| struct sun4i_usb_phy_data *data = dev_get_drvdata(dev); |
| |
| if (args->args[0] >= data->cfg->num_phys) |
| return ERR_PTR(-ENODEV); |
| |
| return data->phys[args->args[0]].phy; |
| } |
| |
| static int sun4i_usb_phy_remove(struct platform_device *pdev) |
| { |
| struct device *dev = &pdev->dev; |
| struct sun4i_usb_phy_data *data = dev_get_drvdata(dev); |
| |
| if (data->vbus_power_nb_registered) |
| power_supply_unreg_notifier(&data->vbus_power_nb); |
| if (data->id_det_irq > 0) |
| devm_free_irq(dev, data->id_det_irq, data); |
| if (data->vbus_det_irq > 0) |
| devm_free_irq(dev, data->vbus_det_irq, data); |
| |
| cancel_delayed_work_sync(&data->detect); |
| |
| return 0; |
| } |
| |
| static const unsigned int sun4i_usb_phy0_cable[] = { |
| EXTCON_USB, |
| EXTCON_USB_HOST, |
| EXTCON_NONE, |
| }; |
| |
| static int sun4i_usb_phy_probe(struct platform_device *pdev) |
| { |
| struct sun4i_usb_phy_data *data; |
| struct device *dev = &pdev->dev; |
| struct device_node *np = dev->of_node; |
| struct phy_provider *phy_provider; |
| struct resource *res; |
| int i, ret; |
| |
| data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL); |
| if (!data) |
| return -ENOMEM; |
| |
| spin_lock_init(&data->reg_lock); |
| INIT_DELAYED_WORK(&data->detect, sun4i_usb_phy0_id_vbus_det_scan); |
| dev_set_drvdata(dev, data); |
| data->cfg = of_device_get_match_data(dev); |
| if (!data->cfg) |
| return -EINVAL; |
| |
| res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "phy_ctrl"); |
| data->base = devm_ioremap_resource(dev, res); |
| if (IS_ERR(data->base)) |
| return PTR_ERR(data->base); |
| |
| data->id_det_gpio = devm_gpiod_get_optional(dev, "usb0_id_det", |
| GPIOD_IN); |
| if (IS_ERR(data->id_det_gpio)) { |
| dev_err(dev, "Couldn't request ID GPIO\n"); |
| return PTR_ERR(data->id_det_gpio); |
| } |
| |
| data->vbus_det_gpio = devm_gpiod_get_optional(dev, "usb0_vbus_det", |
| GPIOD_IN); |
| if (IS_ERR(data->vbus_det_gpio)) { |
| dev_err(dev, "Couldn't request VBUS detect GPIO\n"); |
| return PTR_ERR(data->vbus_det_gpio); |
| } |
| |
| if (of_find_property(np, "usb0_vbus_power-supply", NULL)) { |
| data->vbus_power_supply = devm_power_supply_get_by_phandle(dev, |
| "usb0_vbus_power-supply"); |
| if (IS_ERR(data->vbus_power_supply)) { |
| dev_err(dev, "Couldn't get the VBUS power supply\n"); |
| return PTR_ERR(data->vbus_power_supply); |
| } |
| |
| if (!data->vbus_power_supply) |
| return -EPROBE_DEFER; |
| } |
| |
| data->dr_mode = of_usb_get_dr_mode_by_phy(np, 0); |
| |
| data->extcon = devm_extcon_dev_allocate(dev, sun4i_usb_phy0_cable); |
| if (IS_ERR(data->extcon)) { |
| dev_err(dev, "Couldn't allocate our extcon device\n"); |
| return PTR_ERR(data->extcon); |
| } |
| |
| ret = devm_extcon_dev_register(dev, data->extcon); |
| if (ret) { |
| dev_err(dev, "failed to register extcon: %d\n", ret); |
| return ret; |
| } |
| |
| for (i = 0; i < data->cfg->num_phys; i++) { |
| struct sun4i_usb_phy *phy = data->phys + i; |
| char name[16]; |
| |
| snprintf(name, sizeof(name), "usb%d_vbus", i); |
| phy->vbus = devm_regulator_get_optional(dev, name); |
| if (IS_ERR(phy->vbus)) { |
| if (PTR_ERR(phy->vbus) == -EPROBE_DEFER) { |
| dev_err(dev, |
| "Couldn't get regulator %s... Deferring probe\n", |
| name); |
| return -EPROBE_DEFER; |
| } |
| |
| phy->vbus = NULL; |
| } |
| |
| if (data->cfg->dedicated_clocks) |
| snprintf(name, sizeof(name), "usb%d_phy", i); |
| else |
| strlcpy(name, "usb_phy", sizeof(name)); |
| |
| phy->clk = devm_clk_get(dev, name); |
| if (IS_ERR(phy->clk)) { |
| dev_err(dev, "failed to get clock %s\n", name); |
| return PTR_ERR(phy->clk); |
| } |
| |
| /* The first PHY is always tied to OTG, and never HSIC */ |
| if (data->cfg->hsic_index && i == data->cfg->hsic_index) { |
| /* HSIC needs secondary clock */ |
| snprintf(name, sizeof(name), "usb%d_hsic_12M", i); |
| phy->clk2 = devm_clk_get(dev, name); |
| if (IS_ERR(phy->clk2)) { |
| dev_err(dev, "failed to get clock %s\n", name); |
| return PTR_ERR(phy->clk2); |
| } |
| } |
| |
| snprintf(name, sizeof(name), "usb%d_reset", i); |
| phy->reset = devm_reset_control_get(dev, name); |
| if (IS_ERR(phy->reset)) { |
| dev_err(dev, "failed to get reset %s\n", name); |
| return PTR_ERR(phy->reset); |
| } |
| |
| if (i || data->cfg->phy0_dual_route) { /* No pmu for musb */ |
| snprintf(name, sizeof(name), "pmu%d", i); |
| res = platform_get_resource_byname(pdev, |
| IORESOURCE_MEM, name); |
| phy->pmu = devm_ioremap_resource(dev, res); |
| if (IS_ERR(phy->pmu)) |
| return PTR_ERR(phy->pmu); |
| } |
| |
| phy->phy = devm_phy_create(dev, NULL, &sun4i_usb_phy_ops); |
| if (IS_ERR(phy->phy)) { |
| dev_err(dev, "failed to create PHY %d\n", i); |
| return PTR_ERR(phy->phy); |
| } |
| |
| phy->index = i; |
| phy_set_drvdata(phy->phy, &data->phys[i]); |
| } |
| |
| data->id_det_irq = gpiod_to_irq(data->id_det_gpio); |
| if (data->id_det_irq > 0) { |
| ret = devm_request_irq(dev, data->id_det_irq, |
| sun4i_usb_phy0_id_vbus_det_irq, |
| IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING, |
| "usb0-id-det", data); |
| if (ret) { |
| dev_err(dev, "Err requesting id-det-irq: %d\n", ret); |
| return ret; |
| } |
| } |
| |
| data->vbus_det_irq = gpiod_to_irq(data->vbus_det_gpio); |
| if (data->vbus_det_irq > 0) { |
| ret = devm_request_irq(dev, data->vbus_det_irq, |
| sun4i_usb_phy0_id_vbus_det_irq, |
| IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING, |
| "usb0-vbus-det", data); |
| if (ret) { |
| dev_err(dev, "Err requesting vbus-det-irq: %d\n", ret); |
| data->vbus_det_irq = -1; |
| sun4i_usb_phy_remove(pdev); /* Stop detect work */ |
| return ret; |
| } |
| } |
| |
| if (data->vbus_power_supply) { |
| data->vbus_power_nb.notifier_call = sun4i_usb_phy0_vbus_notify; |
| data->vbus_power_nb.priority = 0; |
| ret = power_supply_reg_notifier(&data->vbus_power_nb); |
| if (ret) { |
| sun4i_usb_phy_remove(pdev); /* Stop detect work */ |
| return ret; |
| } |
| data->vbus_power_nb_registered = true; |
| } |
| |
| phy_provider = devm_of_phy_provider_register(dev, sun4i_usb_phy_xlate); |
| if (IS_ERR(phy_provider)) { |
| sun4i_usb_phy_remove(pdev); /* Stop detect work */ |
| return PTR_ERR(phy_provider); |
| } |
| |
| dev_dbg(dev, "successfully loaded\n"); |
| |
| return 0; |
| } |
| |
| static const struct sun4i_usb_phy_cfg sun4i_a10_cfg = { |
| .num_phys = 3, |
| .type = sun4i_a10_phy, |
| .disc_thresh = 3, |
| .phyctl_offset = REG_PHYCTL_A10, |
| .dedicated_clocks = false, |
| .enable_pmu_unk1 = false, |
| }; |
| |
| static const struct sun4i_usb_phy_cfg sun5i_a13_cfg = { |
| .num_phys = 2, |
| .type = sun4i_a10_phy, |
| .disc_thresh = 2, |
| .phyctl_offset = REG_PHYCTL_A10, |
| .dedicated_clocks = false, |
| .enable_pmu_unk1 = false, |
| }; |
| |
| static const struct sun4i_usb_phy_cfg sun6i_a31_cfg = { |
| .num_phys = 3, |
| .type = sun6i_a31_phy, |
| .disc_thresh = 3, |
| .phyctl_offset = REG_PHYCTL_A10, |
| .dedicated_clocks = true, |
| .enable_pmu_unk1 = false, |
| }; |
| |
| static const struct sun4i_usb_phy_cfg sun7i_a20_cfg = { |
| .num_phys = 3, |
| .type = sun4i_a10_phy, |
| .disc_thresh = 2, |
| .phyctl_offset = REG_PHYCTL_A10, |
| .dedicated_clocks = false, |
| .enable_pmu_unk1 = false, |
| }; |
| |
| static const struct sun4i_usb_phy_cfg sun8i_a23_cfg = { |
| .num_phys = 2, |
| .type = sun6i_a31_phy, |
| .disc_thresh = 3, |
| .phyctl_offset = REG_PHYCTL_A10, |
| .dedicated_clocks = true, |
| .enable_pmu_unk1 = false, |
| }; |
| |
| static const struct sun4i_usb_phy_cfg sun8i_a33_cfg = { |
| .num_phys = 2, |
| .type = sun8i_a33_phy, |
| .disc_thresh = 3, |
| .phyctl_offset = REG_PHYCTL_A33, |
| .dedicated_clocks = true, |
| .enable_pmu_unk1 = false, |
| }; |
| |
| static const struct sun4i_usb_phy_cfg sun8i_a83t_cfg = { |
| .num_phys = 3, |
| .hsic_index = 2, |
| .type = sun8i_a83t_phy, |
| .phyctl_offset = REG_PHYCTL_A33, |
| .dedicated_clocks = true, |
| }; |
| |
| static const struct sun4i_usb_phy_cfg sun8i_h3_cfg = { |
| .num_phys = 4, |
| .type = sun8i_h3_phy, |
| .disc_thresh = 3, |
| .phyctl_offset = REG_PHYCTL_A33, |
| .dedicated_clocks = true, |
| .enable_pmu_unk1 = true, |
| .phy0_dual_route = true, |
| }; |
| |
| static const struct sun4i_usb_phy_cfg sun8i_v3s_cfg = { |
| .num_phys = 1, |
| .type = sun8i_v3s_phy, |
| .disc_thresh = 3, |
| .phyctl_offset = REG_PHYCTL_A33, |
| .dedicated_clocks = true, |
| .enable_pmu_unk1 = true, |
| }; |
| |
| static const struct sun4i_usb_phy_cfg sun50i_a64_cfg = { |
| .num_phys = 2, |
| .type = sun50i_a64_phy, |
| .disc_thresh = 3, |
| .phyctl_offset = REG_PHYCTL_A33, |
| .dedicated_clocks = true, |
| .enable_pmu_unk1 = true, |
| .phy0_dual_route = true, |
| }; |
| |
| static const struct of_device_id sun4i_usb_phy_of_match[] = { |
| { .compatible = "allwinner,sun4i-a10-usb-phy", .data = &sun4i_a10_cfg }, |
| { .compatible = "allwinner,sun5i-a13-usb-phy", .data = &sun5i_a13_cfg }, |
| { .compatible = "allwinner,sun6i-a31-usb-phy", .data = &sun6i_a31_cfg }, |
| { .compatible = "allwinner,sun7i-a20-usb-phy", .data = &sun7i_a20_cfg }, |
| { .compatible = "allwinner,sun8i-a23-usb-phy", .data = &sun8i_a23_cfg }, |
| { .compatible = "allwinner,sun8i-a33-usb-phy", .data = &sun8i_a33_cfg }, |
| { .compatible = "allwinner,sun8i-a83t-usb-phy", .data = &sun8i_a83t_cfg }, |
| { .compatible = "allwinner,sun8i-h3-usb-phy", .data = &sun8i_h3_cfg }, |
| { .compatible = "allwinner,sun8i-v3s-usb-phy", .data = &sun8i_v3s_cfg }, |
| { .compatible = "allwinner,sun50i-a64-usb-phy", |
| .data = &sun50i_a64_cfg}, |
| { }, |
| }; |
| MODULE_DEVICE_TABLE(of, sun4i_usb_phy_of_match); |
| |
| static struct platform_driver sun4i_usb_phy_driver = { |
| .probe = sun4i_usb_phy_probe, |
| .remove = sun4i_usb_phy_remove, |
| .driver = { |
| .of_match_table = sun4i_usb_phy_of_match, |
| .name = "sun4i-usb-phy", |
| } |
| }; |
| module_platform_driver(sun4i_usb_phy_driver); |
| |
| MODULE_DESCRIPTION("Allwinner sun4i USB phy driver"); |
| MODULE_AUTHOR("Hans de Goede <hdegoede@redhat.com>"); |
| MODULE_LICENSE("GPL v2"); |