| /* |
| * Pinctrl driver for Rockchip SoCs |
| * |
| * Copyright (c) 2013 MundoReader S.L. |
| * Author: Heiko Stuebner <heiko@sntech.de> |
| * |
| * With some ideas taken from pinctrl-samsung: |
| * Copyright (c) 2012 Samsung Electronics Co., Ltd. |
| * http://www.samsung.com |
| * Copyright (c) 2012 Linaro Ltd |
| * http://www.linaro.org |
| * |
| * and pinctrl-at91: |
| * Copyright (C) 2011-2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 as published |
| * by the Free Software Foundation. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| */ |
| |
| #include <linux/module.h> |
| #include <linux/platform_device.h> |
| #include <linux/io.h> |
| #include <linux/bitops.h> |
| #include <linux/gpio.h> |
| #include <linux/of_address.h> |
| #include <linux/of_irq.h> |
| #include <linux/pinctrl/machine.h> |
| #include <linux/pinctrl/pinconf.h> |
| #include <linux/pinctrl/pinctrl.h> |
| #include <linux/pinctrl/pinmux.h> |
| #include <linux/pinctrl/pinconf-generic.h> |
| #include <linux/irqchip/chained_irq.h> |
| #include <linux/clk.h> |
| #include <linux/regmap.h> |
| #include <linux/mfd/syscon.h> |
| #include <dt-bindings/pinctrl/rockchip.h> |
| |
| #include "core.h" |
| #include "pinconf.h" |
| |
| /* GPIO control registers */ |
| #define GPIO_SWPORT_DR 0x00 |
| #define GPIO_SWPORT_DDR 0x04 |
| #define GPIO_INTEN 0x30 |
| #define GPIO_INTMASK 0x34 |
| #define GPIO_INTTYPE_LEVEL 0x38 |
| #define GPIO_INT_POLARITY 0x3c |
| #define GPIO_INT_STATUS 0x40 |
| #define GPIO_INT_RAWSTATUS 0x44 |
| #define GPIO_DEBOUNCE 0x48 |
| #define GPIO_PORTS_EOI 0x4c |
| #define GPIO_EXT_PORT 0x50 |
| #define GPIO_LS_SYNC 0x60 |
| |
| enum rockchip_pinctrl_type { |
| RK2928, |
| RK3066B, |
| RK3188, |
| RK3288, |
| RK3368, |
| }; |
| |
| /** |
| * Encode variants of iomux registers into a type variable |
| */ |
| #define IOMUX_GPIO_ONLY BIT(0) |
| #define IOMUX_WIDTH_4BIT BIT(1) |
| #define IOMUX_SOURCE_PMU BIT(2) |
| #define IOMUX_UNROUTED BIT(3) |
| |
| /** |
| * @type: iomux variant using IOMUX_* constants |
| * @offset: if initialized to -1 it will be autocalculated, by specifying |
| * an initial offset value the relevant source offset can be reset |
| * to a new value for autocalculating the following iomux registers. |
| */ |
| struct rockchip_iomux { |
| int type; |
| int offset; |
| }; |
| |
| /** |
| * @reg_base: register base of the gpio bank |
| * @reg_pull: optional separate register for additional pull settings |
| * @clk: clock of the gpio bank |
| * @irq: interrupt of the gpio bank |
| * @saved_masks: Saved content of GPIO_INTEN at suspend time. |
| * @pin_base: first pin number |
| * @nr_pins: number of pins in this bank |
| * @name: name of the bank |
| * @bank_num: number of the bank, to account for holes |
| * @iomux: array describing the 4 iomux sources of the bank |
| * @valid: are all necessary informations present |
| * @of_node: dt node of this bank |
| * @drvdata: common pinctrl basedata |
| * @domain: irqdomain of the gpio bank |
| * @gpio_chip: gpiolib chip |
| * @grange: gpio range |
| * @slock: spinlock for the gpio bank |
| */ |
| struct rockchip_pin_bank { |
| void __iomem *reg_base; |
| struct regmap *regmap_pull; |
| struct clk *clk; |
| int irq; |
| u32 saved_masks; |
| u32 pin_base; |
| u8 nr_pins; |
| char *name; |
| u8 bank_num; |
| struct rockchip_iomux iomux[4]; |
| bool valid; |
| struct device_node *of_node; |
| struct rockchip_pinctrl *drvdata; |
| struct irq_domain *domain; |
| struct gpio_chip gpio_chip; |
| struct pinctrl_gpio_range grange; |
| spinlock_t slock; |
| u32 toggle_edge_mode; |
| }; |
| |
| #define PIN_BANK(id, pins, label) \ |
| { \ |
| .bank_num = id, \ |
| .nr_pins = pins, \ |
| .name = label, \ |
| .iomux = { \ |
| { .offset = -1 }, \ |
| { .offset = -1 }, \ |
| { .offset = -1 }, \ |
| { .offset = -1 }, \ |
| }, \ |
| } |
| |
| #define PIN_BANK_IOMUX_FLAGS(id, pins, label, iom0, iom1, iom2, iom3) \ |
| { \ |
| .bank_num = id, \ |
| .nr_pins = pins, \ |
| .name = label, \ |
| .iomux = { \ |
| { .type = iom0, .offset = -1 }, \ |
| { .type = iom1, .offset = -1 }, \ |
| { .type = iom2, .offset = -1 }, \ |
| { .type = iom3, .offset = -1 }, \ |
| }, \ |
| } |
| |
| /** |
| */ |
| struct rockchip_pin_ctrl { |
| struct rockchip_pin_bank *pin_banks; |
| u32 nr_banks; |
| u32 nr_pins; |
| char *label; |
| enum rockchip_pinctrl_type type; |
| int grf_mux_offset; |
| int pmu_mux_offset; |
| void (*pull_calc_reg)(struct rockchip_pin_bank *bank, |
| int pin_num, struct regmap **regmap, |
| int *reg, u8 *bit); |
| void (*drv_calc_reg)(struct rockchip_pin_bank *bank, |
| int pin_num, struct regmap **regmap, |
| int *reg, u8 *bit); |
| }; |
| |
| struct rockchip_pin_config { |
| unsigned int func; |
| unsigned long *configs; |
| unsigned int nconfigs; |
| }; |
| |
| /** |
| * struct rockchip_pin_group: represent group of pins of a pinmux function. |
| * @name: name of the pin group, used to lookup the group. |
| * @pins: the pins included in this group. |
| * @npins: number of pins included in this group. |
| * @func: the mux function number to be programmed when selected. |
| * @configs: the config values to be set for each pin |
| * @nconfigs: number of configs for each pin |
| */ |
| struct rockchip_pin_group { |
| const char *name; |
| unsigned int npins; |
| unsigned int *pins; |
| struct rockchip_pin_config *data; |
| }; |
| |
| /** |
| * struct rockchip_pmx_func: represent a pin function. |
| * @name: name of the pin function, used to lookup the function. |
| * @groups: one or more names of pin groups that provide this function. |
| * @num_groups: number of groups included in @groups. |
| */ |
| struct rockchip_pmx_func { |
| const char *name; |
| const char **groups; |
| u8 ngroups; |
| }; |
| |
| struct rockchip_pinctrl { |
| struct regmap *regmap_base; |
| int reg_size; |
| struct regmap *regmap_pull; |
| struct regmap *regmap_pmu; |
| struct device *dev; |
| struct rockchip_pin_ctrl *ctrl; |
| struct pinctrl_desc pctl; |
| struct pinctrl_dev *pctl_dev; |
| struct rockchip_pin_group *groups; |
| unsigned int ngroups; |
| struct rockchip_pmx_func *functions; |
| unsigned int nfunctions; |
| }; |
| |
| static struct regmap_config rockchip_regmap_config = { |
| .reg_bits = 32, |
| .val_bits = 32, |
| .reg_stride = 4, |
| }; |
| |
| static inline struct rockchip_pin_bank *gc_to_pin_bank(struct gpio_chip *gc) |
| { |
| return container_of(gc, struct rockchip_pin_bank, gpio_chip); |
| } |
| |
| static const inline struct rockchip_pin_group *pinctrl_name_to_group( |
| const struct rockchip_pinctrl *info, |
| const char *name) |
| { |
| int i; |
| |
| for (i = 0; i < info->ngroups; i++) { |
| if (!strcmp(info->groups[i].name, name)) |
| return &info->groups[i]; |
| } |
| |
| return NULL; |
| } |
| |
| /* |
| * given a pin number that is local to a pin controller, find out the pin bank |
| * and the register base of the pin bank. |
| */ |
| static struct rockchip_pin_bank *pin_to_bank(struct rockchip_pinctrl *info, |
| unsigned pin) |
| { |
| struct rockchip_pin_bank *b = info->ctrl->pin_banks; |
| |
| while (pin >= (b->pin_base + b->nr_pins)) |
| b++; |
| |
| return b; |
| } |
| |
| static struct rockchip_pin_bank *bank_num_to_bank( |
| struct rockchip_pinctrl *info, |
| unsigned num) |
| { |
| struct rockchip_pin_bank *b = info->ctrl->pin_banks; |
| int i; |
| |
| for (i = 0; i < info->ctrl->nr_banks; i++, b++) { |
| if (b->bank_num == num) |
| return b; |
| } |
| |
| return ERR_PTR(-EINVAL); |
| } |
| |
| /* |
| * Pinctrl_ops handling |
| */ |
| |
| static int rockchip_get_groups_count(struct pinctrl_dev *pctldev) |
| { |
| struct rockchip_pinctrl *info = pinctrl_dev_get_drvdata(pctldev); |
| |
| return info->ngroups; |
| } |
| |
| static const char *rockchip_get_group_name(struct pinctrl_dev *pctldev, |
| unsigned selector) |
| { |
| struct rockchip_pinctrl *info = pinctrl_dev_get_drvdata(pctldev); |
| |
| return info->groups[selector].name; |
| } |
| |
| static int rockchip_get_group_pins(struct pinctrl_dev *pctldev, |
| unsigned selector, const unsigned **pins, |
| unsigned *npins) |
| { |
| struct rockchip_pinctrl *info = pinctrl_dev_get_drvdata(pctldev); |
| |
| if (selector >= info->ngroups) |
| return -EINVAL; |
| |
| *pins = info->groups[selector].pins; |
| *npins = info->groups[selector].npins; |
| |
| return 0; |
| } |
| |
| static int rockchip_dt_node_to_map(struct pinctrl_dev *pctldev, |
| struct device_node *np, |
| struct pinctrl_map **map, unsigned *num_maps) |
| { |
| struct rockchip_pinctrl *info = pinctrl_dev_get_drvdata(pctldev); |
| const struct rockchip_pin_group *grp; |
| struct pinctrl_map *new_map; |
| struct device_node *parent; |
| int map_num = 1; |
| int i; |
| |
| /* |
| * first find the group of this node and check if we need to create |
| * config maps for pins |
| */ |
| grp = pinctrl_name_to_group(info, np->name); |
| if (!grp) { |
| dev_err(info->dev, "unable to find group for node %s\n", |
| np->name); |
| return -EINVAL; |
| } |
| |
| map_num += grp->npins; |
| new_map = devm_kzalloc(pctldev->dev, sizeof(*new_map) * map_num, |
| GFP_KERNEL); |
| if (!new_map) |
| return -ENOMEM; |
| |
| *map = new_map; |
| *num_maps = map_num; |
| |
| /* create mux map */ |
| parent = of_get_parent(np); |
| if (!parent) { |
| devm_kfree(pctldev->dev, new_map); |
| return -EINVAL; |
| } |
| new_map[0].type = PIN_MAP_TYPE_MUX_GROUP; |
| new_map[0].data.mux.function = parent->name; |
| new_map[0].data.mux.group = np->name; |
| of_node_put(parent); |
| |
| /* create config map */ |
| new_map++; |
| for (i = 0; i < grp->npins; i++) { |
| new_map[i].type = PIN_MAP_TYPE_CONFIGS_PIN; |
| new_map[i].data.configs.group_or_pin = |
| pin_get_name(pctldev, grp->pins[i]); |
| new_map[i].data.configs.configs = grp->data[i].configs; |
| new_map[i].data.configs.num_configs = grp->data[i].nconfigs; |
| } |
| |
| dev_dbg(pctldev->dev, "maps: function %s group %s num %d\n", |
| (*map)->data.mux.function, (*map)->data.mux.group, map_num); |
| |
| return 0; |
| } |
| |
| static void rockchip_dt_free_map(struct pinctrl_dev *pctldev, |
| struct pinctrl_map *map, unsigned num_maps) |
| { |
| } |
| |
| static const struct pinctrl_ops rockchip_pctrl_ops = { |
| .get_groups_count = rockchip_get_groups_count, |
| .get_group_name = rockchip_get_group_name, |
| .get_group_pins = rockchip_get_group_pins, |
| .dt_node_to_map = rockchip_dt_node_to_map, |
| .dt_free_map = rockchip_dt_free_map, |
| }; |
| |
| /* |
| * Hardware access |
| */ |
| |
| static int rockchip_get_mux(struct rockchip_pin_bank *bank, int pin) |
| { |
| struct rockchip_pinctrl *info = bank->drvdata; |
| int iomux_num = (pin / 8); |
| struct regmap *regmap; |
| unsigned int val; |
| int reg, ret, mask; |
| u8 bit; |
| |
| if (iomux_num > 3) |
| return -EINVAL; |
| |
| if (bank->iomux[iomux_num].type & IOMUX_UNROUTED) { |
| dev_err(info->dev, "pin %d is unrouted\n", pin); |
| return -EINVAL; |
| } |
| |
| if (bank->iomux[iomux_num].type & IOMUX_GPIO_ONLY) |
| return RK_FUNC_GPIO; |
| |
| regmap = (bank->iomux[iomux_num].type & IOMUX_SOURCE_PMU) |
| ? info->regmap_pmu : info->regmap_base; |
| |
| /* get basic quadrupel of mux registers and the correct reg inside */ |
| mask = (bank->iomux[iomux_num].type & IOMUX_WIDTH_4BIT) ? 0xf : 0x3; |
| reg = bank->iomux[iomux_num].offset; |
| if (bank->iomux[iomux_num].type & IOMUX_WIDTH_4BIT) { |
| if ((pin % 8) >= 4) |
| reg += 0x4; |
| bit = (pin % 4) * 4; |
| } else { |
| bit = (pin % 8) * 2; |
| } |
| |
| ret = regmap_read(regmap, reg, &val); |
| if (ret) |
| return ret; |
| |
| return ((val >> bit) & mask); |
| } |
| |
| /* |
| * Set a new mux function for a pin. |
| * |
| * The register is divided into the upper and lower 16 bit. When changing |
| * a value, the previous register value is not read and changed. Instead |
| * it seems the changed bits are marked in the upper 16 bit, while the |
| * changed value gets set in the same offset in the lower 16 bit. |
| * All pin settings seem to be 2 bit wide in both the upper and lower |
| * parts. |
| * @bank: pin bank to change |
| * @pin: pin to change |
| * @mux: new mux function to set |
| */ |
| static int rockchip_set_mux(struct rockchip_pin_bank *bank, int pin, int mux) |
| { |
| struct rockchip_pinctrl *info = bank->drvdata; |
| int iomux_num = (pin / 8); |
| struct regmap *regmap; |
| int reg, ret, mask; |
| unsigned long flags; |
| u8 bit; |
| u32 data, rmask; |
| |
| if (iomux_num > 3) |
| return -EINVAL; |
| |
| if (bank->iomux[iomux_num].type & IOMUX_UNROUTED) { |
| dev_err(info->dev, "pin %d is unrouted\n", pin); |
| return -EINVAL; |
| } |
| |
| if (bank->iomux[iomux_num].type & IOMUX_GPIO_ONLY) { |
| if (mux != RK_FUNC_GPIO) { |
| dev_err(info->dev, |
| "pin %d only supports a gpio mux\n", pin); |
| return -ENOTSUPP; |
| } else { |
| return 0; |
| } |
| } |
| |
| dev_dbg(info->dev, "setting mux of GPIO%d-%d to %d\n", |
| bank->bank_num, pin, mux); |
| |
| regmap = (bank->iomux[iomux_num].type & IOMUX_SOURCE_PMU) |
| ? info->regmap_pmu : info->regmap_base; |
| |
| /* get basic quadrupel of mux registers and the correct reg inside */ |
| mask = (bank->iomux[iomux_num].type & IOMUX_WIDTH_4BIT) ? 0xf : 0x3; |
| reg = bank->iomux[iomux_num].offset; |
| if (bank->iomux[iomux_num].type & IOMUX_WIDTH_4BIT) { |
| if ((pin % 8) >= 4) |
| reg += 0x4; |
| bit = (pin % 4) * 4; |
| } else { |
| bit = (pin % 8) * 2; |
| } |
| |
| spin_lock_irqsave(&bank->slock, flags); |
| |
| data = (mask << (bit + 16)); |
| rmask = data | (data >> 16); |
| data |= (mux & mask) << bit; |
| ret = regmap_update_bits(regmap, reg, rmask, data); |
| |
| spin_unlock_irqrestore(&bank->slock, flags); |
| |
| return ret; |
| } |
| |
| #define RK2928_PULL_OFFSET 0x118 |
| #define RK2928_PULL_PINS_PER_REG 16 |
| #define RK2928_PULL_BANK_STRIDE 8 |
| |
| static void rk2928_calc_pull_reg_and_bit(struct rockchip_pin_bank *bank, |
| int pin_num, struct regmap **regmap, |
| int *reg, u8 *bit) |
| { |
| struct rockchip_pinctrl *info = bank->drvdata; |
| |
| *regmap = info->regmap_base; |
| *reg = RK2928_PULL_OFFSET; |
| *reg += bank->bank_num * RK2928_PULL_BANK_STRIDE; |
| *reg += (pin_num / RK2928_PULL_PINS_PER_REG) * 4; |
| |
| *bit = pin_num % RK2928_PULL_PINS_PER_REG; |
| }; |
| |
| #define RK3188_PULL_OFFSET 0x164 |
| #define RK3188_PULL_BITS_PER_PIN 2 |
| #define RK3188_PULL_PINS_PER_REG 8 |
| #define RK3188_PULL_BANK_STRIDE 16 |
| #define RK3188_PULL_PMU_OFFSET 0x64 |
| |
| static void rk3188_calc_pull_reg_and_bit(struct rockchip_pin_bank *bank, |
| int pin_num, struct regmap **regmap, |
| int *reg, u8 *bit) |
| { |
| struct rockchip_pinctrl *info = bank->drvdata; |
| |
| /* The first 12 pins of the first bank are located elsewhere */ |
| if (bank->bank_num == 0 && pin_num < 12) { |
| *regmap = info->regmap_pmu ? info->regmap_pmu |
| : bank->regmap_pull; |
| *reg = info->regmap_pmu ? RK3188_PULL_PMU_OFFSET : 0; |
| *reg += ((pin_num / RK3188_PULL_PINS_PER_REG) * 4); |
| *bit = pin_num % RK3188_PULL_PINS_PER_REG; |
| *bit *= RK3188_PULL_BITS_PER_PIN; |
| } else { |
| *regmap = info->regmap_pull ? info->regmap_pull |
| : info->regmap_base; |
| *reg = info->regmap_pull ? 0 : RK3188_PULL_OFFSET; |
| |
| /* correct the offset, as it is the 2nd pull register */ |
| *reg -= 4; |
| *reg += bank->bank_num * RK3188_PULL_BANK_STRIDE; |
| *reg += ((pin_num / RK3188_PULL_PINS_PER_REG) * 4); |
| |
| /* |
| * The bits in these registers have an inverse ordering |
| * with the lowest pin being in bits 15:14 and the highest |
| * pin in bits 1:0 |
| */ |
| *bit = 7 - (pin_num % RK3188_PULL_PINS_PER_REG); |
| *bit *= RK3188_PULL_BITS_PER_PIN; |
| } |
| } |
| |
| #define RK3288_PULL_OFFSET 0x140 |
| static void rk3288_calc_pull_reg_and_bit(struct rockchip_pin_bank *bank, |
| int pin_num, struct regmap **regmap, |
| int *reg, u8 *bit) |
| { |
| struct rockchip_pinctrl *info = bank->drvdata; |
| |
| /* The first 24 pins of the first bank are located in PMU */ |
| if (bank->bank_num == 0) { |
| *regmap = info->regmap_pmu; |
| *reg = RK3188_PULL_PMU_OFFSET; |
| |
| *reg += ((pin_num / RK3188_PULL_PINS_PER_REG) * 4); |
| *bit = pin_num % RK3188_PULL_PINS_PER_REG; |
| *bit *= RK3188_PULL_BITS_PER_PIN; |
| } else { |
| *regmap = info->regmap_base; |
| *reg = RK3288_PULL_OFFSET; |
| |
| /* correct the offset, as we're starting with the 2nd bank */ |
| *reg -= 0x10; |
| *reg += bank->bank_num * RK3188_PULL_BANK_STRIDE; |
| *reg += ((pin_num / RK3188_PULL_PINS_PER_REG) * 4); |
| |
| *bit = (pin_num % RK3188_PULL_PINS_PER_REG); |
| *bit *= RK3188_PULL_BITS_PER_PIN; |
| } |
| } |
| |
| #define RK3288_DRV_PMU_OFFSET 0x70 |
| #define RK3288_DRV_GRF_OFFSET 0x1c0 |
| #define RK3288_DRV_BITS_PER_PIN 2 |
| #define RK3288_DRV_PINS_PER_REG 8 |
| #define RK3288_DRV_BANK_STRIDE 16 |
| |
| static void rk3288_calc_drv_reg_and_bit(struct rockchip_pin_bank *bank, |
| int pin_num, struct regmap **regmap, |
| int *reg, u8 *bit) |
| { |
| struct rockchip_pinctrl *info = bank->drvdata; |
| |
| /* The first 24 pins of the first bank are located in PMU */ |
| if (bank->bank_num == 0) { |
| *regmap = info->regmap_pmu; |
| *reg = RK3288_DRV_PMU_OFFSET; |
| |
| *reg += ((pin_num / RK3288_DRV_PINS_PER_REG) * 4); |
| *bit = pin_num % RK3288_DRV_PINS_PER_REG; |
| *bit *= RK3288_DRV_BITS_PER_PIN; |
| } else { |
| *regmap = info->regmap_base; |
| *reg = RK3288_DRV_GRF_OFFSET; |
| |
| /* correct the offset, as we're starting with the 2nd bank */ |
| *reg -= 0x10; |
| *reg += bank->bank_num * RK3288_DRV_BANK_STRIDE; |
| *reg += ((pin_num / RK3288_DRV_PINS_PER_REG) * 4); |
| |
| *bit = (pin_num % RK3288_DRV_PINS_PER_REG); |
| *bit *= RK3288_DRV_BITS_PER_PIN; |
| } |
| } |
| |
| #define RK3368_PULL_GRF_OFFSET 0x100 |
| #define RK3368_PULL_PMU_OFFSET 0x10 |
| |
| static void rk3368_calc_pull_reg_and_bit(struct rockchip_pin_bank *bank, |
| int pin_num, struct regmap **regmap, |
| int *reg, u8 *bit) |
| { |
| struct rockchip_pinctrl *info = bank->drvdata; |
| |
| /* The first 32 pins of the first bank are located in PMU */ |
| if (bank->bank_num == 0) { |
| *regmap = info->regmap_pmu; |
| *reg = RK3368_PULL_PMU_OFFSET; |
| |
| *reg += ((pin_num / RK3188_PULL_PINS_PER_REG) * 4); |
| *bit = pin_num % RK3188_PULL_PINS_PER_REG; |
| *bit *= RK3188_PULL_BITS_PER_PIN; |
| } else { |
| *regmap = info->regmap_base; |
| *reg = RK3368_PULL_GRF_OFFSET; |
| |
| /* correct the offset, as we're starting with the 2nd bank */ |
| *reg -= 0x10; |
| *reg += bank->bank_num * RK3188_PULL_BANK_STRIDE; |
| *reg += ((pin_num / RK3188_PULL_PINS_PER_REG) * 4); |
| |
| *bit = (pin_num % RK3188_PULL_PINS_PER_REG); |
| *bit *= RK3188_PULL_BITS_PER_PIN; |
| } |
| } |
| |
| #define RK3368_DRV_PMU_OFFSET 0x20 |
| #define RK3368_DRV_GRF_OFFSET 0x200 |
| |
| static void rk3368_calc_drv_reg_and_bit(struct rockchip_pin_bank *bank, |
| int pin_num, struct regmap **regmap, |
| int *reg, u8 *bit) |
| { |
| struct rockchip_pinctrl *info = bank->drvdata; |
| |
| /* The first 32 pins of the first bank are located in PMU */ |
| if (bank->bank_num == 0) { |
| *regmap = info->regmap_pmu; |
| *reg = RK3368_DRV_PMU_OFFSET; |
| |
| *reg += ((pin_num / RK3288_DRV_PINS_PER_REG) * 4); |
| *bit = pin_num % RK3288_DRV_PINS_PER_REG; |
| *bit *= RK3288_DRV_BITS_PER_PIN; |
| } else { |
| *regmap = info->regmap_base; |
| *reg = RK3368_DRV_GRF_OFFSET; |
| |
| /* correct the offset, as we're starting with the 2nd bank */ |
| *reg -= 0x10; |
| *reg += bank->bank_num * RK3288_DRV_BANK_STRIDE; |
| *reg += ((pin_num / RK3288_DRV_PINS_PER_REG) * 4); |
| |
| *bit = (pin_num % RK3288_DRV_PINS_PER_REG); |
| *bit *= RK3288_DRV_BITS_PER_PIN; |
| } |
| } |
| |
| static int rockchip_perpin_drv_list[] = { 2, 4, 8, 12 }; |
| |
| static int rockchip_get_drive_perpin(struct rockchip_pin_bank *bank, |
| int pin_num) |
| { |
| struct rockchip_pinctrl *info = bank->drvdata; |
| struct rockchip_pin_ctrl *ctrl = info->ctrl; |
| struct regmap *regmap; |
| int reg, ret; |
| u32 data; |
| u8 bit; |
| |
| ctrl->drv_calc_reg(bank, pin_num, ®map, ®, &bit); |
| |
| ret = regmap_read(regmap, reg, &data); |
| if (ret) |
| return ret; |
| |
| data >>= bit; |
| data &= (1 << RK3288_DRV_BITS_PER_PIN) - 1; |
| |
| return rockchip_perpin_drv_list[data]; |
| } |
| |
| static int rockchip_set_drive_perpin(struct rockchip_pin_bank *bank, |
| int pin_num, int strength) |
| { |
| struct rockchip_pinctrl *info = bank->drvdata; |
| struct rockchip_pin_ctrl *ctrl = info->ctrl; |
| struct regmap *regmap; |
| unsigned long flags; |
| int reg, ret, i; |
| u32 data, rmask; |
| u8 bit; |
| |
| ctrl->drv_calc_reg(bank, pin_num, ®map, ®, &bit); |
| |
| ret = -EINVAL; |
| for (i = 0; i < ARRAY_SIZE(rockchip_perpin_drv_list); i++) { |
| if (rockchip_perpin_drv_list[i] == strength) { |
| ret = i; |
| break; |
| } |
| } |
| |
| if (ret < 0) { |
| dev_err(info->dev, "unsupported driver strength %d\n", |
| strength); |
| return ret; |
| } |
| |
| spin_lock_irqsave(&bank->slock, flags); |
| |
| /* enable the write to the equivalent lower bits */ |
| data = ((1 << RK3288_DRV_BITS_PER_PIN) - 1) << (bit + 16); |
| rmask = data | (data >> 16); |
| data |= (ret << bit); |
| |
| ret = regmap_update_bits(regmap, reg, rmask, data); |
| spin_unlock_irqrestore(&bank->slock, flags); |
| |
| return ret; |
| } |
| |
| static int rockchip_get_pull(struct rockchip_pin_bank *bank, int pin_num) |
| { |
| struct rockchip_pinctrl *info = bank->drvdata; |
| struct rockchip_pin_ctrl *ctrl = info->ctrl; |
| struct regmap *regmap; |
| int reg, ret; |
| u8 bit; |
| u32 data; |
| |
| /* rk3066b does support any pulls */ |
| if (ctrl->type == RK3066B) |
| return PIN_CONFIG_BIAS_DISABLE; |
| |
| ctrl->pull_calc_reg(bank, pin_num, ®map, ®, &bit); |
| |
| ret = regmap_read(regmap, reg, &data); |
| if (ret) |
| return ret; |
| |
| switch (ctrl->type) { |
| case RK2928: |
| return !(data & BIT(bit)) |
| ? PIN_CONFIG_BIAS_PULL_PIN_DEFAULT |
| : PIN_CONFIG_BIAS_DISABLE; |
| case RK3188: |
| case RK3288: |
| case RK3368: |
| data >>= bit; |
| data &= (1 << RK3188_PULL_BITS_PER_PIN) - 1; |
| |
| switch (data) { |
| case 0: |
| return PIN_CONFIG_BIAS_DISABLE; |
| case 1: |
| return PIN_CONFIG_BIAS_PULL_UP; |
| case 2: |
| return PIN_CONFIG_BIAS_PULL_DOWN; |
| case 3: |
| return PIN_CONFIG_BIAS_BUS_HOLD; |
| } |
| |
| dev_err(info->dev, "unknown pull setting\n"); |
| return -EIO; |
| default: |
| dev_err(info->dev, "unsupported pinctrl type\n"); |
| return -EINVAL; |
| }; |
| } |
| |
| static int rockchip_set_pull(struct rockchip_pin_bank *bank, |
| int pin_num, int pull) |
| { |
| struct rockchip_pinctrl *info = bank->drvdata; |
| struct rockchip_pin_ctrl *ctrl = info->ctrl; |
| struct regmap *regmap; |
| int reg, ret; |
| unsigned long flags; |
| u8 bit; |
| u32 data, rmask; |
| |
| dev_dbg(info->dev, "setting pull of GPIO%d-%d to %d\n", |
| bank->bank_num, pin_num, pull); |
| |
| /* rk3066b does support any pulls */ |
| if (ctrl->type == RK3066B) |
| return pull ? -EINVAL : 0; |
| |
| ctrl->pull_calc_reg(bank, pin_num, ®map, ®, &bit); |
| |
| switch (ctrl->type) { |
| case RK2928: |
| spin_lock_irqsave(&bank->slock, flags); |
| |
| data = BIT(bit + 16); |
| if (pull == PIN_CONFIG_BIAS_DISABLE) |
| data |= BIT(bit); |
| ret = regmap_write(regmap, reg, data); |
| |
| spin_unlock_irqrestore(&bank->slock, flags); |
| break; |
| case RK3188: |
| case RK3288: |
| case RK3368: |
| spin_lock_irqsave(&bank->slock, flags); |
| |
| /* enable the write to the equivalent lower bits */ |
| data = ((1 << RK3188_PULL_BITS_PER_PIN) - 1) << (bit + 16); |
| rmask = data | (data >> 16); |
| |
| switch (pull) { |
| case PIN_CONFIG_BIAS_DISABLE: |
| break; |
| case PIN_CONFIG_BIAS_PULL_UP: |
| data |= (1 << bit); |
| break; |
| case PIN_CONFIG_BIAS_PULL_DOWN: |
| data |= (2 << bit); |
| break; |
| case PIN_CONFIG_BIAS_BUS_HOLD: |
| data |= (3 << bit); |
| break; |
| default: |
| spin_unlock_irqrestore(&bank->slock, flags); |
| dev_err(info->dev, "unsupported pull setting %d\n", |
| pull); |
| return -EINVAL; |
| } |
| |
| ret = regmap_update_bits(regmap, reg, rmask, data); |
| |
| spin_unlock_irqrestore(&bank->slock, flags); |
| break; |
| default: |
| dev_err(info->dev, "unsupported pinctrl type\n"); |
| return -EINVAL; |
| } |
| |
| return ret; |
| } |
| |
| /* |
| * Pinmux_ops handling |
| */ |
| |
| static int rockchip_pmx_get_funcs_count(struct pinctrl_dev *pctldev) |
| { |
| struct rockchip_pinctrl *info = pinctrl_dev_get_drvdata(pctldev); |
| |
| return info->nfunctions; |
| } |
| |
| static const char *rockchip_pmx_get_func_name(struct pinctrl_dev *pctldev, |
| unsigned selector) |
| { |
| struct rockchip_pinctrl *info = pinctrl_dev_get_drvdata(pctldev); |
| |
| return info->functions[selector].name; |
| } |
| |
| static int rockchip_pmx_get_groups(struct pinctrl_dev *pctldev, |
| unsigned selector, const char * const **groups, |
| unsigned * const num_groups) |
| { |
| struct rockchip_pinctrl *info = pinctrl_dev_get_drvdata(pctldev); |
| |
| *groups = info->functions[selector].groups; |
| *num_groups = info->functions[selector].ngroups; |
| |
| return 0; |
| } |
| |
| static int rockchip_pmx_set(struct pinctrl_dev *pctldev, unsigned selector, |
| unsigned group) |
| { |
| struct rockchip_pinctrl *info = pinctrl_dev_get_drvdata(pctldev); |
| const unsigned int *pins = info->groups[group].pins; |
| const struct rockchip_pin_config *data = info->groups[group].data; |
| struct rockchip_pin_bank *bank; |
| int cnt, ret = 0; |
| |
| dev_dbg(info->dev, "enable function %s group %s\n", |
| info->functions[selector].name, info->groups[group].name); |
| |
| /* |
| * for each pin in the pin group selected, program the correspoding pin |
| * pin function number in the config register. |
| */ |
| for (cnt = 0; cnt < info->groups[group].npins; cnt++) { |
| bank = pin_to_bank(info, pins[cnt]); |
| ret = rockchip_set_mux(bank, pins[cnt] - bank->pin_base, |
| data[cnt].func); |
| if (ret) |
| break; |
| } |
| |
| if (ret) { |
| /* revert the already done pin settings */ |
| for (cnt--; cnt >= 0; cnt--) |
| rockchip_set_mux(bank, pins[cnt] - bank->pin_base, 0); |
| |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| /* |
| * The calls to gpio_direction_output() and gpio_direction_input() |
| * leads to this function call (via the pinctrl_gpio_direction_{input|output}() |
| * function called from the gpiolib interface). |
| */ |
| static int _rockchip_pmx_gpio_set_direction(struct gpio_chip *chip, |
| int pin, bool input) |
| { |
| struct rockchip_pin_bank *bank; |
| int ret; |
| unsigned long flags; |
| u32 data; |
| |
| bank = gc_to_pin_bank(chip); |
| |
| ret = rockchip_set_mux(bank, pin, RK_FUNC_GPIO); |
| if (ret < 0) |
| return ret; |
| |
| spin_lock_irqsave(&bank->slock, flags); |
| |
| data = readl_relaxed(bank->reg_base + GPIO_SWPORT_DDR); |
| /* set bit to 1 for output, 0 for input */ |
| if (!input) |
| data |= BIT(pin); |
| else |
| data &= ~BIT(pin); |
| writel_relaxed(data, bank->reg_base + GPIO_SWPORT_DDR); |
| |
| spin_unlock_irqrestore(&bank->slock, flags); |
| |
| return 0; |
| } |
| |
| static int rockchip_pmx_gpio_set_direction(struct pinctrl_dev *pctldev, |
| struct pinctrl_gpio_range *range, |
| unsigned offset, bool input) |
| { |
| struct rockchip_pinctrl *info = pinctrl_dev_get_drvdata(pctldev); |
| struct gpio_chip *chip; |
| int pin; |
| |
| chip = range->gc; |
| pin = offset - chip->base; |
| dev_dbg(info->dev, "gpio_direction for pin %u as %s-%d to %s\n", |
| offset, range->name, pin, input ? "input" : "output"); |
| |
| return _rockchip_pmx_gpio_set_direction(chip, offset - chip->base, |
| input); |
| } |
| |
| static const struct pinmux_ops rockchip_pmx_ops = { |
| .get_functions_count = rockchip_pmx_get_funcs_count, |
| .get_function_name = rockchip_pmx_get_func_name, |
| .get_function_groups = rockchip_pmx_get_groups, |
| .set_mux = rockchip_pmx_set, |
| .gpio_set_direction = rockchip_pmx_gpio_set_direction, |
| }; |
| |
| /* |
| * Pinconf_ops handling |
| */ |
| |
| static bool rockchip_pinconf_pull_valid(struct rockchip_pin_ctrl *ctrl, |
| enum pin_config_param pull) |
| { |
| switch (ctrl->type) { |
| case RK2928: |
| return (pull == PIN_CONFIG_BIAS_PULL_PIN_DEFAULT || |
| pull == PIN_CONFIG_BIAS_DISABLE); |
| case RK3066B: |
| return pull ? false : true; |
| case RK3188: |
| case RK3288: |
| case RK3368: |
| return (pull != PIN_CONFIG_BIAS_PULL_PIN_DEFAULT); |
| } |
| |
| return false; |
| } |
| |
| static void rockchip_gpio_set(struct gpio_chip *gc, unsigned offset, int value); |
| static int rockchip_gpio_get(struct gpio_chip *gc, unsigned offset); |
| |
| /* set the pin config settings for a specified pin */ |
| static int rockchip_pinconf_set(struct pinctrl_dev *pctldev, unsigned int pin, |
| unsigned long *configs, unsigned num_configs) |
| { |
| struct rockchip_pinctrl *info = pinctrl_dev_get_drvdata(pctldev); |
| struct rockchip_pin_bank *bank = pin_to_bank(info, pin); |
| enum pin_config_param param; |
| u16 arg; |
| int i; |
| int rc; |
| |
| for (i = 0; i < num_configs; i++) { |
| param = pinconf_to_config_param(configs[i]); |
| arg = pinconf_to_config_argument(configs[i]); |
| |
| switch (param) { |
| case PIN_CONFIG_BIAS_DISABLE: |
| rc = rockchip_set_pull(bank, pin - bank->pin_base, |
| param); |
| if (rc) |
| return rc; |
| break; |
| case PIN_CONFIG_BIAS_PULL_UP: |
| case PIN_CONFIG_BIAS_PULL_DOWN: |
| case PIN_CONFIG_BIAS_PULL_PIN_DEFAULT: |
| case PIN_CONFIG_BIAS_BUS_HOLD: |
| if (!rockchip_pinconf_pull_valid(info->ctrl, param)) |
| return -ENOTSUPP; |
| |
| if (!arg) |
| return -EINVAL; |
| |
| rc = rockchip_set_pull(bank, pin - bank->pin_base, |
| param); |
| if (rc) |
| return rc; |
| break; |
| case PIN_CONFIG_OUTPUT: |
| rockchip_gpio_set(&bank->gpio_chip, |
| pin - bank->pin_base, arg); |
| rc = _rockchip_pmx_gpio_set_direction(&bank->gpio_chip, |
| pin - bank->pin_base, false); |
| if (rc) |
| return rc; |
| break; |
| case PIN_CONFIG_DRIVE_STRENGTH: |
| /* rk3288 is the first with per-pin drive-strength */ |
| if (!info->ctrl->drv_calc_reg) |
| return -ENOTSUPP; |
| |
| rc = rockchip_set_drive_perpin(bank, |
| pin - bank->pin_base, arg); |
| if (rc < 0) |
| return rc; |
| break; |
| default: |
| return -ENOTSUPP; |
| break; |
| } |
| } /* for each config */ |
| |
| return 0; |
| } |
| |
| /* get the pin config settings for a specified pin */ |
| static int rockchip_pinconf_get(struct pinctrl_dev *pctldev, unsigned int pin, |
| unsigned long *config) |
| { |
| struct rockchip_pinctrl *info = pinctrl_dev_get_drvdata(pctldev); |
| struct rockchip_pin_bank *bank = pin_to_bank(info, pin); |
| enum pin_config_param param = pinconf_to_config_param(*config); |
| u16 arg; |
| int rc; |
| |
| switch (param) { |
| case PIN_CONFIG_BIAS_DISABLE: |
| if (rockchip_get_pull(bank, pin - bank->pin_base) != param) |
| return -EINVAL; |
| |
| arg = 0; |
| break; |
| case PIN_CONFIG_BIAS_PULL_UP: |
| case PIN_CONFIG_BIAS_PULL_DOWN: |
| case PIN_CONFIG_BIAS_PULL_PIN_DEFAULT: |
| case PIN_CONFIG_BIAS_BUS_HOLD: |
| if (!rockchip_pinconf_pull_valid(info->ctrl, param)) |
| return -ENOTSUPP; |
| |
| if (rockchip_get_pull(bank, pin - bank->pin_base) != param) |
| return -EINVAL; |
| |
| arg = 1; |
| break; |
| case PIN_CONFIG_OUTPUT: |
| rc = rockchip_get_mux(bank, pin - bank->pin_base); |
| if (rc != RK_FUNC_GPIO) |
| return -EINVAL; |
| |
| rc = rockchip_gpio_get(&bank->gpio_chip, pin - bank->pin_base); |
| if (rc < 0) |
| return rc; |
| |
| arg = rc ? 1 : 0; |
| break; |
| case PIN_CONFIG_DRIVE_STRENGTH: |
| /* rk3288 is the first with per-pin drive-strength */ |
| if (!info->ctrl->drv_calc_reg) |
| return -ENOTSUPP; |
| |
| rc = rockchip_get_drive_perpin(bank, pin - bank->pin_base); |
| if (rc < 0) |
| return rc; |
| |
| arg = rc; |
| break; |
| default: |
| return -ENOTSUPP; |
| break; |
| } |
| |
| *config = pinconf_to_config_packed(param, arg); |
| |
| return 0; |
| } |
| |
| static const struct pinconf_ops rockchip_pinconf_ops = { |
| .pin_config_get = rockchip_pinconf_get, |
| .pin_config_set = rockchip_pinconf_set, |
| .is_generic = true, |
| }; |
| |
| static const struct of_device_id rockchip_bank_match[] = { |
| { .compatible = "rockchip,gpio-bank" }, |
| { .compatible = "rockchip,rk3188-gpio-bank0" }, |
| {}, |
| }; |
| |
| static void rockchip_pinctrl_child_count(struct rockchip_pinctrl *info, |
| struct device_node *np) |
| { |
| struct device_node *child; |
| |
| for_each_child_of_node(np, child) { |
| if (of_match_node(rockchip_bank_match, child)) |
| continue; |
| |
| info->nfunctions++; |
| info->ngroups += of_get_child_count(child); |
| } |
| } |
| |
| static int rockchip_pinctrl_parse_groups(struct device_node *np, |
| struct rockchip_pin_group *grp, |
| struct rockchip_pinctrl *info, |
| u32 index) |
| { |
| struct rockchip_pin_bank *bank; |
| int size; |
| const __be32 *list; |
| int num; |
| int i, j; |
| int ret; |
| |
| dev_dbg(info->dev, "group(%d): %s\n", index, np->name); |
| |
| /* Initialise group */ |
| grp->name = np->name; |
| |
| /* |
| * the binding format is rockchip,pins = <bank pin mux CONFIG>, |
| * do sanity check and calculate pins number |
| */ |
| list = of_get_property(np, "rockchip,pins", &size); |
| /* we do not check return since it's safe node passed down */ |
| size /= sizeof(*list); |
| if (!size || size % 4) { |
| dev_err(info->dev, "wrong pins number or pins and configs should be by 4\n"); |
| return -EINVAL; |
| } |
| |
| grp->npins = size / 4; |
| |
| grp->pins = devm_kzalloc(info->dev, grp->npins * sizeof(unsigned int), |
| GFP_KERNEL); |
| grp->data = devm_kzalloc(info->dev, grp->npins * |
| sizeof(struct rockchip_pin_config), |
| GFP_KERNEL); |
| if (!grp->pins || !grp->data) |
| return -ENOMEM; |
| |
| for (i = 0, j = 0; i < size; i += 4, j++) { |
| const __be32 *phandle; |
| struct device_node *np_config; |
| |
| num = be32_to_cpu(*list++); |
| bank = bank_num_to_bank(info, num); |
| if (IS_ERR(bank)) |
| return PTR_ERR(bank); |
| |
| grp->pins[j] = bank->pin_base + be32_to_cpu(*list++); |
| grp->data[j].func = be32_to_cpu(*list++); |
| |
| phandle = list++; |
| if (!phandle) |
| return -EINVAL; |
| |
| np_config = of_find_node_by_phandle(be32_to_cpup(phandle)); |
| ret = pinconf_generic_parse_dt_config(np_config, NULL, |
| &grp->data[j].configs, &grp->data[j].nconfigs); |
| if (ret) |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static int rockchip_pinctrl_parse_functions(struct device_node *np, |
| struct rockchip_pinctrl *info, |
| u32 index) |
| { |
| struct device_node *child; |
| struct rockchip_pmx_func *func; |
| struct rockchip_pin_group *grp; |
| int ret; |
| static u32 grp_index; |
| u32 i = 0; |
| |
| dev_dbg(info->dev, "parse function(%d): %s\n", index, np->name); |
| |
| func = &info->functions[index]; |
| |
| /* Initialise function */ |
| func->name = np->name; |
| func->ngroups = of_get_child_count(np); |
| if (func->ngroups <= 0) |
| return 0; |
| |
| func->groups = devm_kzalloc(info->dev, |
| func->ngroups * sizeof(char *), GFP_KERNEL); |
| if (!func->groups) |
| return -ENOMEM; |
| |
| for_each_child_of_node(np, child) { |
| func->groups[i] = child->name; |
| grp = &info->groups[grp_index++]; |
| ret = rockchip_pinctrl_parse_groups(child, grp, info, i++); |
| if (ret) |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static int rockchip_pinctrl_parse_dt(struct platform_device *pdev, |
| struct rockchip_pinctrl *info) |
| { |
| struct device *dev = &pdev->dev; |
| struct device_node *np = dev->of_node; |
| struct device_node *child; |
| int ret; |
| int i; |
| |
| rockchip_pinctrl_child_count(info, np); |
| |
| dev_dbg(&pdev->dev, "nfunctions = %d\n", info->nfunctions); |
| dev_dbg(&pdev->dev, "ngroups = %d\n", info->ngroups); |
| |
| info->functions = devm_kzalloc(dev, info->nfunctions * |
| sizeof(struct rockchip_pmx_func), |
| GFP_KERNEL); |
| if (!info->functions) { |
| dev_err(dev, "failed to allocate memory for function list\n"); |
| return -EINVAL; |
| } |
| |
| info->groups = devm_kzalloc(dev, info->ngroups * |
| sizeof(struct rockchip_pin_group), |
| GFP_KERNEL); |
| if (!info->groups) { |
| dev_err(dev, "failed allocate memory for ping group list\n"); |
| return -EINVAL; |
| } |
| |
| i = 0; |
| |
| for_each_child_of_node(np, child) { |
| if (of_match_node(rockchip_bank_match, child)) |
| continue; |
| |
| ret = rockchip_pinctrl_parse_functions(child, info, i++); |
| if (ret) { |
| dev_err(&pdev->dev, "failed to parse function\n"); |
| return ret; |
| } |
| } |
| |
| return 0; |
| } |
| |
| static int rockchip_pinctrl_register(struct platform_device *pdev, |
| struct rockchip_pinctrl *info) |
| { |
| struct pinctrl_desc *ctrldesc = &info->pctl; |
| struct pinctrl_pin_desc *pindesc, *pdesc; |
| struct rockchip_pin_bank *pin_bank; |
| int pin, bank, ret; |
| int k; |
| |
| ctrldesc->name = "rockchip-pinctrl"; |
| ctrldesc->owner = THIS_MODULE; |
| ctrldesc->pctlops = &rockchip_pctrl_ops; |
| ctrldesc->pmxops = &rockchip_pmx_ops; |
| ctrldesc->confops = &rockchip_pinconf_ops; |
| |
| pindesc = devm_kzalloc(&pdev->dev, sizeof(*pindesc) * |
| info->ctrl->nr_pins, GFP_KERNEL); |
| if (!pindesc) { |
| dev_err(&pdev->dev, "mem alloc for pin descriptors failed\n"); |
| return -ENOMEM; |
| } |
| ctrldesc->pins = pindesc; |
| ctrldesc->npins = info->ctrl->nr_pins; |
| |
| pdesc = pindesc; |
| for (bank = 0 , k = 0; bank < info->ctrl->nr_banks; bank++) { |
| pin_bank = &info->ctrl->pin_banks[bank]; |
| for (pin = 0; pin < pin_bank->nr_pins; pin++, k++) { |
| pdesc->number = k; |
| pdesc->name = kasprintf(GFP_KERNEL, "%s-%d", |
| pin_bank->name, pin); |
| pdesc++; |
| } |
| } |
| |
| ret = rockchip_pinctrl_parse_dt(pdev, info); |
| if (ret) |
| return ret; |
| |
| info->pctl_dev = pinctrl_register(ctrldesc, &pdev->dev, info); |
| if (IS_ERR(info->pctl_dev)) { |
| dev_err(&pdev->dev, "could not register pinctrl driver\n"); |
| return PTR_ERR(info->pctl_dev); |
| } |
| |
| for (bank = 0; bank < info->ctrl->nr_banks; ++bank) { |
| pin_bank = &info->ctrl->pin_banks[bank]; |
| pin_bank->grange.name = pin_bank->name; |
| pin_bank->grange.id = bank; |
| pin_bank->grange.pin_base = pin_bank->pin_base; |
| pin_bank->grange.base = pin_bank->gpio_chip.base; |
| pin_bank->grange.npins = pin_bank->gpio_chip.ngpio; |
| pin_bank->grange.gc = &pin_bank->gpio_chip; |
| pinctrl_add_gpio_range(info->pctl_dev, &pin_bank->grange); |
| } |
| |
| return 0; |
| } |
| |
| /* |
| * GPIO handling |
| */ |
| |
| static int rockchip_gpio_request(struct gpio_chip *chip, unsigned offset) |
| { |
| return pinctrl_request_gpio(chip->base + offset); |
| } |
| |
| static void rockchip_gpio_free(struct gpio_chip *chip, unsigned offset) |
| { |
| pinctrl_free_gpio(chip->base + offset); |
| } |
| |
| static void rockchip_gpio_set(struct gpio_chip *gc, unsigned offset, int value) |
| { |
| struct rockchip_pin_bank *bank = gc_to_pin_bank(gc); |
| void __iomem *reg = bank->reg_base + GPIO_SWPORT_DR; |
| unsigned long flags; |
| u32 data; |
| |
| spin_lock_irqsave(&bank->slock, flags); |
| |
| data = readl(reg); |
| data &= ~BIT(offset); |
| if (value) |
| data |= BIT(offset); |
| writel(data, reg); |
| |
| spin_unlock_irqrestore(&bank->slock, flags); |
| } |
| |
| /* |
| * Returns the level of the pin for input direction and setting of the DR |
| * register for output gpios. |
| */ |
| static int rockchip_gpio_get(struct gpio_chip *gc, unsigned offset) |
| { |
| struct rockchip_pin_bank *bank = gc_to_pin_bank(gc); |
| u32 data; |
| |
| data = readl(bank->reg_base + GPIO_EXT_PORT); |
| data >>= offset; |
| data &= 1; |
| return data; |
| } |
| |
| /* |
| * gpiolib gpio_direction_input callback function. The setting of the pin |
| * mux function as 'gpio input' will be handled by the pinctrl susbsystem |
| * interface. |
| */ |
| static int rockchip_gpio_direction_input(struct gpio_chip *gc, unsigned offset) |
| { |
| return pinctrl_gpio_direction_input(gc->base + offset); |
| } |
| |
| /* |
| * gpiolib gpio_direction_output callback function. The setting of the pin |
| * mux function as 'gpio output' will be handled by the pinctrl susbsystem |
| * interface. |
| */ |
| static int rockchip_gpio_direction_output(struct gpio_chip *gc, |
| unsigned offset, int value) |
| { |
| rockchip_gpio_set(gc, offset, value); |
| return pinctrl_gpio_direction_output(gc->base + offset); |
| } |
| |
| /* |
| * gpiolib gpio_to_irq callback function. Creates a mapping between a GPIO pin |
| * and a virtual IRQ, if not already present. |
| */ |
| static int rockchip_gpio_to_irq(struct gpio_chip *gc, unsigned offset) |
| { |
| struct rockchip_pin_bank *bank = gc_to_pin_bank(gc); |
| unsigned int virq; |
| |
| if (!bank->domain) |
| return -ENXIO; |
| |
| virq = irq_create_mapping(bank->domain, offset); |
| |
| return (virq) ? : -ENXIO; |
| } |
| |
| static const struct gpio_chip rockchip_gpiolib_chip = { |
| .request = rockchip_gpio_request, |
| .free = rockchip_gpio_free, |
| .set = rockchip_gpio_set, |
| .get = rockchip_gpio_get, |
| .direction_input = rockchip_gpio_direction_input, |
| .direction_output = rockchip_gpio_direction_output, |
| .to_irq = rockchip_gpio_to_irq, |
| .owner = THIS_MODULE, |
| }; |
| |
| /* |
| * Interrupt handling |
| */ |
| |
| static void rockchip_irq_demux(unsigned int irq, struct irq_desc *desc) |
| { |
| struct irq_chip *chip = irq_desc_get_chip(desc); |
| struct rockchip_pin_bank *bank = irq_desc_get_handler_data(desc); |
| u32 pend; |
| |
| dev_dbg(bank->drvdata->dev, "got irq for bank %s\n", bank->name); |
| |
| chained_irq_enter(chip, desc); |
| |
| pend = readl_relaxed(bank->reg_base + GPIO_INT_STATUS); |
| |
| while (pend) { |
| unsigned int virq; |
| |
| irq = __ffs(pend); |
| pend &= ~BIT(irq); |
| virq = irq_linear_revmap(bank->domain, irq); |
| |
| if (!virq) { |
| dev_err(bank->drvdata->dev, "unmapped irq %d\n", irq); |
| continue; |
| } |
| |
| dev_dbg(bank->drvdata->dev, "handling irq %d\n", irq); |
| |
| /* |
| * Triggering IRQ on both rising and falling edge |
| * needs manual intervention. |
| */ |
| if (bank->toggle_edge_mode & BIT(irq)) { |
| u32 data, data_old, polarity; |
| unsigned long flags; |
| |
| data = readl_relaxed(bank->reg_base + GPIO_EXT_PORT); |
| do { |
| spin_lock_irqsave(&bank->slock, flags); |
| |
| polarity = readl_relaxed(bank->reg_base + |
| GPIO_INT_POLARITY); |
| if (data & BIT(irq)) |
| polarity &= ~BIT(irq); |
| else |
| polarity |= BIT(irq); |
| writel(polarity, |
| bank->reg_base + GPIO_INT_POLARITY); |
| |
| spin_unlock_irqrestore(&bank->slock, flags); |
| |
| data_old = data; |
| data = readl_relaxed(bank->reg_base + |
| GPIO_EXT_PORT); |
| } while ((data & BIT(irq)) != (data_old & BIT(irq))); |
| } |
| |
| generic_handle_irq(virq); |
| } |
| |
| chained_irq_exit(chip, desc); |
| } |
| |
| static int rockchip_irq_set_type(struct irq_data *d, unsigned int type) |
| { |
| struct irq_chip_generic *gc = irq_data_get_irq_chip_data(d); |
| struct rockchip_pin_bank *bank = gc->private; |
| u32 mask = BIT(d->hwirq); |
| u32 polarity; |
| u32 level; |
| u32 data; |
| unsigned long flags; |
| int ret; |
| |
| /* make sure the pin is configured as gpio input */ |
| ret = rockchip_set_mux(bank, d->hwirq, RK_FUNC_GPIO); |
| if (ret < 0) |
| return ret; |
| |
| spin_lock_irqsave(&bank->slock, flags); |
| |
| data = readl_relaxed(bank->reg_base + GPIO_SWPORT_DDR); |
| data &= ~mask; |
| writel_relaxed(data, bank->reg_base + GPIO_SWPORT_DDR); |
| |
| spin_unlock_irqrestore(&bank->slock, flags); |
| |
| if (type & IRQ_TYPE_EDGE_BOTH) |
| irq_set_handler_locked(d, handle_edge_irq); |
| else |
| irq_set_handler_locked(d, handle_level_irq); |
| |
| spin_lock_irqsave(&bank->slock, flags); |
| irq_gc_lock(gc); |
| |
| level = readl_relaxed(gc->reg_base + GPIO_INTTYPE_LEVEL); |
| polarity = readl_relaxed(gc->reg_base + GPIO_INT_POLARITY); |
| |
| switch (type) { |
| case IRQ_TYPE_EDGE_BOTH: |
| bank->toggle_edge_mode |= mask; |
| level |= mask; |
| |
| /* |
| * Determine gpio state. If 1 next interrupt should be falling |
| * otherwise rising. |
| */ |
| data = readl(bank->reg_base + GPIO_EXT_PORT); |
| if (data & mask) |
| polarity &= ~mask; |
| else |
| polarity |= mask; |
| break; |
| case IRQ_TYPE_EDGE_RISING: |
| bank->toggle_edge_mode &= ~mask; |
| level |= mask; |
| polarity |= mask; |
| break; |
| case IRQ_TYPE_EDGE_FALLING: |
| bank->toggle_edge_mode &= ~mask; |
| level |= mask; |
| polarity &= ~mask; |
| break; |
| case IRQ_TYPE_LEVEL_HIGH: |
| bank->toggle_edge_mode &= ~mask; |
| level &= ~mask; |
| polarity |= mask; |
| break; |
| case IRQ_TYPE_LEVEL_LOW: |
| bank->toggle_edge_mode &= ~mask; |
| level &= ~mask; |
| polarity &= ~mask; |
| break; |
| default: |
| irq_gc_unlock(gc); |
| spin_unlock_irqrestore(&bank->slock, flags); |
| return -EINVAL; |
| } |
| |
| writel_relaxed(level, gc->reg_base + GPIO_INTTYPE_LEVEL); |
| writel_relaxed(polarity, gc->reg_base + GPIO_INT_POLARITY); |
| |
| irq_gc_unlock(gc); |
| spin_unlock_irqrestore(&bank->slock, flags); |
| |
| return 0; |
| } |
| |
| static void rockchip_irq_suspend(struct irq_data *d) |
| { |
| struct irq_chip_generic *gc = irq_data_get_irq_chip_data(d); |
| struct rockchip_pin_bank *bank = gc->private; |
| |
| bank->saved_masks = irq_reg_readl(gc, GPIO_INTMASK); |
| irq_reg_writel(gc, ~gc->wake_active, GPIO_INTMASK); |
| } |
| |
| static void rockchip_irq_resume(struct irq_data *d) |
| { |
| struct irq_chip_generic *gc = irq_data_get_irq_chip_data(d); |
| struct rockchip_pin_bank *bank = gc->private; |
| |
| irq_reg_writel(gc, bank->saved_masks, GPIO_INTMASK); |
| } |
| |
| static int rockchip_interrupts_register(struct platform_device *pdev, |
| struct rockchip_pinctrl *info) |
| { |
| struct rockchip_pin_ctrl *ctrl = info->ctrl; |
| struct rockchip_pin_bank *bank = ctrl->pin_banks; |
| unsigned int clr = IRQ_NOREQUEST | IRQ_NOPROBE | IRQ_NOAUTOEN; |
| struct irq_chip_generic *gc; |
| int ret; |
| int i; |
| |
| for (i = 0; i < ctrl->nr_banks; ++i, ++bank) { |
| if (!bank->valid) { |
| dev_warn(&pdev->dev, "bank %s is not valid\n", |
| bank->name); |
| continue; |
| } |
| |
| bank->domain = irq_domain_add_linear(bank->of_node, 32, |
| &irq_generic_chip_ops, NULL); |
| if (!bank->domain) { |
| dev_warn(&pdev->dev, "could not initialize irq domain for bank %s\n", |
| bank->name); |
| continue; |
| } |
| |
| ret = irq_alloc_domain_generic_chips(bank->domain, 32, 1, |
| "rockchip_gpio_irq", handle_level_irq, |
| clr, 0, IRQ_GC_INIT_MASK_CACHE); |
| if (ret) { |
| dev_err(&pdev->dev, "could not alloc generic chips for bank %s\n", |
| bank->name); |
| irq_domain_remove(bank->domain); |
| continue; |
| } |
| |
| /* |
| * Linux assumes that all interrupts start out disabled/masked. |
| * Our driver only uses the concept of masked and always keeps |
| * things enabled, so for us that's all masked and all enabled. |
| */ |
| writel_relaxed(0xffffffff, bank->reg_base + GPIO_INTMASK); |
| writel_relaxed(0xffffffff, bank->reg_base + GPIO_INTEN); |
| |
| gc = irq_get_domain_generic_chip(bank->domain, 0); |
| gc->reg_base = bank->reg_base; |
| gc->private = bank; |
| gc->chip_types[0].regs.mask = GPIO_INTMASK; |
| gc->chip_types[0].regs.ack = GPIO_PORTS_EOI; |
| gc->chip_types[0].chip.irq_ack = irq_gc_ack_set_bit; |
| gc->chip_types[0].chip.irq_mask = irq_gc_mask_set_bit; |
| gc->chip_types[0].chip.irq_unmask = irq_gc_mask_clr_bit; |
| gc->chip_types[0].chip.irq_set_wake = irq_gc_set_wake; |
| gc->chip_types[0].chip.irq_suspend = rockchip_irq_suspend; |
| gc->chip_types[0].chip.irq_resume = rockchip_irq_resume; |
| gc->chip_types[0].chip.irq_set_type = rockchip_irq_set_type; |
| gc->wake_enabled = IRQ_MSK(bank->nr_pins); |
| |
| irq_set_chained_handler_and_data(bank->irq, |
| rockchip_irq_demux, bank); |
| } |
| |
| return 0; |
| } |
| |
| static int rockchip_gpiolib_register(struct platform_device *pdev, |
| struct rockchip_pinctrl *info) |
| { |
| struct rockchip_pin_ctrl *ctrl = info->ctrl; |
| struct rockchip_pin_bank *bank = ctrl->pin_banks; |
| struct gpio_chip *gc; |
| int ret; |
| int i; |
| |
| for (i = 0; i < ctrl->nr_banks; ++i, ++bank) { |
| if (!bank->valid) { |
| dev_warn(&pdev->dev, "bank %s is not valid\n", |
| bank->name); |
| continue; |
| } |
| |
| bank->gpio_chip = rockchip_gpiolib_chip; |
| |
| gc = &bank->gpio_chip; |
| gc->base = bank->pin_base; |
| gc->ngpio = bank->nr_pins; |
| gc->dev = &pdev->dev; |
| gc->of_node = bank->of_node; |
| gc->label = bank->name; |
| |
| ret = gpiochip_add(gc); |
| if (ret) { |
| dev_err(&pdev->dev, "failed to register gpio_chip %s, error code: %d\n", |
| gc->label, ret); |
| goto fail; |
| } |
| } |
| |
| rockchip_interrupts_register(pdev, info); |
| |
| return 0; |
| |
| fail: |
| for (--i, --bank; i >= 0; --i, --bank) { |
| if (!bank->valid) |
| continue; |
| gpiochip_remove(&bank->gpio_chip); |
| } |
| return ret; |
| } |
| |
| static int rockchip_gpiolib_unregister(struct platform_device *pdev, |
| struct rockchip_pinctrl *info) |
| { |
| struct rockchip_pin_ctrl *ctrl = info->ctrl; |
| struct rockchip_pin_bank *bank = ctrl->pin_banks; |
| int i; |
| |
| for (i = 0; i < ctrl->nr_banks; ++i, ++bank) { |
| if (!bank->valid) |
| continue; |
| gpiochip_remove(&bank->gpio_chip); |
| } |
| |
| return 0; |
| } |
| |
| static int rockchip_get_bank_data(struct rockchip_pin_bank *bank, |
| struct rockchip_pinctrl *info) |
| { |
| struct resource res; |
| void __iomem *base; |
| |
| if (of_address_to_resource(bank->of_node, 0, &res)) { |
| dev_err(info->dev, "cannot find IO resource for bank\n"); |
| return -ENOENT; |
| } |
| |
| bank->reg_base = devm_ioremap_resource(info->dev, &res); |
| if (IS_ERR(bank->reg_base)) |
| return PTR_ERR(bank->reg_base); |
| |
| /* |
| * special case, where parts of the pull setting-registers are |
| * part of the PMU register space |
| */ |
| if (of_device_is_compatible(bank->of_node, |
| "rockchip,rk3188-gpio-bank0")) { |
| struct device_node *node; |
| |
| node = of_parse_phandle(bank->of_node->parent, |
| "rockchip,pmu", 0); |
| if (!node) { |
| if (of_address_to_resource(bank->of_node, 1, &res)) { |
| dev_err(info->dev, "cannot find IO resource for bank\n"); |
| return -ENOENT; |
| } |
| |
| base = devm_ioremap_resource(info->dev, &res); |
| if (IS_ERR(base)) |
| return PTR_ERR(base); |
| rockchip_regmap_config.max_register = |
| resource_size(&res) - 4; |
| rockchip_regmap_config.name = |
| "rockchip,rk3188-gpio-bank0-pull"; |
| bank->regmap_pull = devm_regmap_init_mmio(info->dev, |
| base, |
| &rockchip_regmap_config); |
| } |
| } |
| |
| bank->irq = irq_of_parse_and_map(bank->of_node, 0); |
| |
| bank->clk = of_clk_get(bank->of_node, 0); |
| if (IS_ERR(bank->clk)) |
| return PTR_ERR(bank->clk); |
| |
| return clk_prepare_enable(bank->clk); |
| } |
| |
| static const struct of_device_id rockchip_pinctrl_dt_match[]; |
| |
| /* retrieve the soc specific data */ |
| static struct rockchip_pin_ctrl *rockchip_pinctrl_get_soc_data( |
| struct rockchip_pinctrl *d, |
| struct platform_device *pdev) |
| { |
| const struct of_device_id *match; |
| struct device_node *node = pdev->dev.of_node; |
| struct device_node *np; |
| struct rockchip_pin_ctrl *ctrl; |
| struct rockchip_pin_bank *bank; |
| int grf_offs, pmu_offs, i, j; |
| |
| match = of_match_node(rockchip_pinctrl_dt_match, node); |
| ctrl = (struct rockchip_pin_ctrl *)match->data; |
| |
| for_each_child_of_node(node, np) { |
| if (!of_find_property(np, "gpio-controller", NULL)) |
| continue; |
| |
| bank = ctrl->pin_banks; |
| for (i = 0; i < ctrl->nr_banks; ++i, ++bank) { |
| if (!strcmp(bank->name, np->name)) { |
| bank->of_node = np; |
| |
| if (!rockchip_get_bank_data(bank, d)) |
| bank->valid = true; |
| |
| break; |
| } |
| } |
| } |
| |
| grf_offs = ctrl->grf_mux_offset; |
| pmu_offs = ctrl->pmu_mux_offset; |
| bank = ctrl->pin_banks; |
| for (i = 0; i < ctrl->nr_banks; ++i, ++bank) { |
| int bank_pins = 0; |
| |
| spin_lock_init(&bank->slock); |
| bank->drvdata = d; |
| bank->pin_base = ctrl->nr_pins; |
| ctrl->nr_pins += bank->nr_pins; |
| |
| /* calculate iomux offsets */ |
| for (j = 0; j < 4; j++) { |
| struct rockchip_iomux *iom = &bank->iomux[j]; |
| int inc; |
| |
| if (bank_pins >= bank->nr_pins) |
| break; |
| |
| /* preset offset value, set new start value */ |
| if (iom->offset >= 0) { |
| if (iom->type & IOMUX_SOURCE_PMU) |
| pmu_offs = iom->offset; |
| else |
| grf_offs = iom->offset; |
| } else { /* set current offset */ |
| iom->offset = (iom->type & IOMUX_SOURCE_PMU) ? |
| pmu_offs : grf_offs; |
| } |
| |
| dev_dbg(d->dev, "bank %d, iomux %d has offset 0x%x\n", |
| i, j, iom->offset); |
| |
| /* |
| * Increase offset according to iomux width. |
| * 4bit iomux'es are spread over two registers. |
| */ |
| inc = (iom->type & IOMUX_WIDTH_4BIT) ? 8 : 4; |
| if (iom->type & IOMUX_SOURCE_PMU) |
| pmu_offs += inc; |
| else |
| grf_offs += inc; |
| |
| bank_pins += 8; |
| } |
| } |
| |
| return ctrl; |
| } |
| |
| #define RK3288_GRF_GPIO6C_IOMUX 0x64 |
| #define GPIO6C6_SEL_WRITE_ENABLE BIT(28) |
| |
| static u32 rk3288_grf_gpio6c_iomux; |
| |
| static int __maybe_unused rockchip_pinctrl_suspend(struct device *dev) |
| { |
| struct rockchip_pinctrl *info = dev_get_drvdata(dev); |
| int ret = pinctrl_force_sleep(info->pctl_dev); |
| |
| if (ret) |
| return ret; |
| |
| /* |
| * RK3288 GPIO6_C6 mux would be modified by Maskrom when resume, so save |
| * the setting here, and restore it at resume. |
| */ |
| if (info->ctrl->type == RK3288) { |
| ret = regmap_read(info->regmap_base, RK3288_GRF_GPIO6C_IOMUX, |
| &rk3288_grf_gpio6c_iomux); |
| if (ret) { |
| pinctrl_force_default(info->pctl_dev); |
| return ret; |
| } |
| } |
| |
| return 0; |
| } |
| |
| static int __maybe_unused rockchip_pinctrl_resume(struct device *dev) |
| { |
| struct rockchip_pinctrl *info = dev_get_drvdata(dev); |
| int ret = regmap_write(info->regmap_base, RK3288_GRF_GPIO6C_IOMUX, |
| rk3288_grf_gpio6c_iomux | |
| GPIO6C6_SEL_WRITE_ENABLE); |
| |
| if (ret) |
| return ret; |
| |
| return pinctrl_force_default(info->pctl_dev); |
| } |
| |
| static SIMPLE_DEV_PM_OPS(rockchip_pinctrl_dev_pm_ops, rockchip_pinctrl_suspend, |
| rockchip_pinctrl_resume); |
| |
| static int rockchip_pinctrl_probe(struct platform_device *pdev) |
| { |
| struct rockchip_pinctrl *info; |
| struct device *dev = &pdev->dev; |
| struct rockchip_pin_ctrl *ctrl; |
| struct device_node *np = pdev->dev.of_node, *node; |
| struct resource *res; |
| void __iomem *base; |
| int ret; |
| |
| if (!dev->of_node) { |
| dev_err(dev, "device tree node not found\n"); |
| return -ENODEV; |
| } |
| |
| info = devm_kzalloc(dev, sizeof(struct rockchip_pinctrl), GFP_KERNEL); |
| if (!info) |
| return -ENOMEM; |
| |
| info->dev = dev; |
| |
| ctrl = rockchip_pinctrl_get_soc_data(info, pdev); |
| if (!ctrl) { |
| dev_err(dev, "driver data not available\n"); |
| return -EINVAL; |
| } |
| info->ctrl = ctrl; |
| |
| node = of_parse_phandle(np, "rockchip,grf", 0); |
| if (node) { |
| info->regmap_base = syscon_node_to_regmap(node); |
| if (IS_ERR(info->regmap_base)) |
| return PTR_ERR(info->regmap_base); |
| } else { |
| res = platform_get_resource(pdev, IORESOURCE_MEM, 0); |
| base = devm_ioremap_resource(&pdev->dev, res); |
| if (IS_ERR(base)) |
| return PTR_ERR(base); |
| |
| rockchip_regmap_config.max_register = resource_size(res) - 4; |
| rockchip_regmap_config.name = "rockchip,pinctrl"; |
| info->regmap_base = devm_regmap_init_mmio(&pdev->dev, base, |
| &rockchip_regmap_config); |
| |
| /* to check for the old dt-bindings */ |
| info->reg_size = resource_size(res); |
| |
| /* Honor the old binding, with pull registers as 2nd resource */ |
| if (ctrl->type == RK3188 && info->reg_size < 0x200) { |
| res = platform_get_resource(pdev, IORESOURCE_MEM, 1); |
| base = devm_ioremap_resource(&pdev->dev, res); |
| if (IS_ERR(base)) |
| return PTR_ERR(base); |
| |
| rockchip_regmap_config.max_register = |
| resource_size(res) - 4; |
| rockchip_regmap_config.name = "rockchip,pinctrl-pull"; |
| info->regmap_pull = devm_regmap_init_mmio(&pdev->dev, |
| base, |
| &rockchip_regmap_config); |
| } |
| } |
| |
| /* try to find the optional reference to the pmu syscon */ |
| node = of_parse_phandle(np, "rockchip,pmu", 0); |
| if (node) { |
| info->regmap_pmu = syscon_node_to_regmap(node); |
| if (IS_ERR(info->regmap_pmu)) |
| return PTR_ERR(info->regmap_pmu); |
| } |
| |
| ret = rockchip_gpiolib_register(pdev, info); |
| if (ret) |
| return ret; |
| |
| ret = rockchip_pinctrl_register(pdev, info); |
| if (ret) { |
| rockchip_gpiolib_unregister(pdev, info); |
| return ret; |
| } |
| |
| platform_set_drvdata(pdev, info); |
| |
| return 0; |
| } |
| |
| static struct rockchip_pin_bank rk2928_pin_banks[] = { |
| PIN_BANK(0, 32, "gpio0"), |
| PIN_BANK(1, 32, "gpio1"), |
| PIN_BANK(2, 32, "gpio2"), |
| PIN_BANK(3, 32, "gpio3"), |
| }; |
| |
| static struct rockchip_pin_ctrl rk2928_pin_ctrl = { |
| .pin_banks = rk2928_pin_banks, |
| .nr_banks = ARRAY_SIZE(rk2928_pin_banks), |
| .label = "RK2928-GPIO", |
| .type = RK2928, |
| .grf_mux_offset = 0xa8, |
| .pull_calc_reg = rk2928_calc_pull_reg_and_bit, |
| }; |
| |
| static struct rockchip_pin_bank rk3066a_pin_banks[] = { |
| PIN_BANK(0, 32, "gpio0"), |
| PIN_BANK(1, 32, "gpio1"), |
| PIN_BANK(2, 32, "gpio2"), |
| PIN_BANK(3, 32, "gpio3"), |
| PIN_BANK(4, 32, "gpio4"), |
| PIN_BANK(6, 16, "gpio6"), |
| }; |
| |
| static struct rockchip_pin_ctrl rk3066a_pin_ctrl = { |
| .pin_banks = rk3066a_pin_banks, |
| .nr_banks = ARRAY_SIZE(rk3066a_pin_banks), |
| .label = "RK3066a-GPIO", |
| .type = RK2928, |
| .grf_mux_offset = 0xa8, |
| .pull_calc_reg = rk2928_calc_pull_reg_and_bit, |
| }; |
| |
| static struct rockchip_pin_bank rk3066b_pin_banks[] = { |
| PIN_BANK(0, 32, "gpio0"), |
| PIN_BANK(1, 32, "gpio1"), |
| PIN_BANK(2, 32, "gpio2"), |
| PIN_BANK(3, 32, "gpio3"), |
| }; |
| |
| static struct rockchip_pin_ctrl rk3066b_pin_ctrl = { |
| .pin_banks = rk3066b_pin_banks, |
| .nr_banks = ARRAY_SIZE(rk3066b_pin_banks), |
| .label = "RK3066b-GPIO", |
| .type = RK3066B, |
| .grf_mux_offset = 0x60, |
| }; |
| |
| static struct rockchip_pin_bank rk3188_pin_banks[] = { |
| PIN_BANK_IOMUX_FLAGS(0, 32, "gpio0", IOMUX_GPIO_ONLY, 0, 0, 0), |
| PIN_BANK(1, 32, "gpio1"), |
| PIN_BANK(2, 32, "gpio2"), |
| PIN_BANK(3, 32, "gpio3"), |
| }; |
| |
| static struct rockchip_pin_ctrl rk3188_pin_ctrl = { |
| .pin_banks = rk3188_pin_banks, |
| .nr_banks = ARRAY_SIZE(rk3188_pin_banks), |
| .label = "RK3188-GPIO", |
| .type = RK3188, |
| .grf_mux_offset = 0x60, |
| .pull_calc_reg = rk3188_calc_pull_reg_and_bit, |
| }; |
| |
| static struct rockchip_pin_bank rk3288_pin_banks[] = { |
| PIN_BANK_IOMUX_FLAGS(0, 24, "gpio0", IOMUX_SOURCE_PMU, |
| IOMUX_SOURCE_PMU, |
| IOMUX_SOURCE_PMU, |
| IOMUX_UNROUTED |
| ), |
| PIN_BANK_IOMUX_FLAGS(1, 32, "gpio1", IOMUX_UNROUTED, |
| IOMUX_UNROUTED, |
| IOMUX_UNROUTED, |
| 0 |
| ), |
| PIN_BANK_IOMUX_FLAGS(2, 32, "gpio2", 0, 0, 0, IOMUX_UNROUTED), |
| PIN_BANK_IOMUX_FLAGS(3, 32, "gpio3", 0, 0, 0, IOMUX_WIDTH_4BIT), |
| PIN_BANK_IOMUX_FLAGS(4, 32, "gpio4", IOMUX_WIDTH_4BIT, |
| IOMUX_WIDTH_4BIT, |
| 0, |
| 0 |
| ), |
| PIN_BANK_IOMUX_FLAGS(5, 32, "gpio5", IOMUX_UNROUTED, |
| 0, |
| 0, |
| IOMUX_UNROUTED |
| ), |
| PIN_BANK_IOMUX_FLAGS(6, 32, "gpio6", 0, 0, 0, IOMUX_UNROUTED), |
| PIN_BANK_IOMUX_FLAGS(7, 32, "gpio7", 0, |
| 0, |
| IOMUX_WIDTH_4BIT, |
| IOMUX_UNROUTED |
| ), |
| PIN_BANK(8, 16, "gpio8"), |
| }; |
| |
| static struct rockchip_pin_ctrl rk3288_pin_ctrl = { |
| .pin_banks = rk3288_pin_banks, |
| .nr_banks = ARRAY_SIZE(rk3288_pin_banks), |
| .label = "RK3288-GPIO", |
| .type = RK3288, |
| .grf_mux_offset = 0x0, |
| .pmu_mux_offset = 0x84, |
| .pull_calc_reg = rk3288_calc_pull_reg_and_bit, |
| .drv_calc_reg = rk3288_calc_drv_reg_and_bit, |
| }; |
| |
| static struct rockchip_pin_bank rk3368_pin_banks[] = { |
| PIN_BANK_IOMUX_FLAGS(0, 32, "gpio0", IOMUX_SOURCE_PMU, |
| IOMUX_SOURCE_PMU, |
| IOMUX_SOURCE_PMU, |
| IOMUX_SOURCE_PMU |
| ), |
| PIN_BANK(1, 32, "gpio1"), |
| PIN_BANK(2, 32, "gpio2"), |
| PIN_BANK(3, 32, "gpio3"), |
| }; |
| |
| static struct rockchip_pin_ctrl rk3368_pin_ctrl = { |
| .pin_banks = rk3368_pin_banks, |
| .nr_banks = ARRAY_SIZE(rk3368_pin_banks), |
| .label = "RK3368-GPIO", |
| .type = RK3368, |
| .grf_mux_offset = 0x0, |
| .pmu_mux_offset = 0x0, |
| .pull_calc_reg = rk3368_calc_pull_reg_and_bit, |
| .drv_calc_reg = rk3368_calc_drv_reg_and_bit, |
| }; |
| |
| |
| static const struct of_device_id rockchip_pinctrl_dt_match[] = { |
| { .compatible = "rockchip,rk2928-pinctrl", |
| .data = (void *)&rk2928_pin_ctrl }, |
| { .compatible = "rockchip,rk3066a-pinctrl", |
| .data = (void *)&rk3066a_pin_ctrl }, |
| { .compatible = "rockchip,rk3066b-pinctrl", |
| .data = (void *)&rk3066b_pin_ctrl }, |
| { .compatible = "rockchip,rk3188-pinctrl", |
| .data = (void *)&rk3188_pin_ctrl }, |
| { .compatible = "rockchip,rk3288-pinctrl", |
| .data = (void *)&rk3288_pin_ctrl }, |
| { .compatible = "rockchip,rk3368-pinctrl", |
| .data = (void *)&rk3368_pin_ctrl }, |
| {}, |
| }; |
| MODULE_DEVICE_TABLE(of, rockchip_pinctrl_dt_match); |
| |
| static struct platform_driver rockchip_pinctrl_driver = { |
| .probe = rockchip_pinctrl_probe, |
| .driver = { |
| .name = "rockchip-pinctrl", |
| .pm = &rockchip_pinctrl_dev_pm_ops, |
| .of_match_table = rockchip_pinctrl_dt_match, |
| }, |
| }; |
| |
| static int __init rockchip_pinctrl_drv_register(void) |
| { |
| return platform_driver_register(&rockchip_pinctrl_driver); |
| } |
| postcore_initcall(rockchip_pinctrl_drv_register); |
| |
| MODULE_AUTHOR("Heiko Stuebner <heiko@sntech.de>"); |
| MODULE_DESCRIPTION("Rockchip pinctrl driver"); |
| MODULE_LICENSE("GPL v2"); |