| /* bnx2x_main.c: Broadcom Everest network driver. |
| * |
| * Copyright (c) 2007-2010 Broadcom Corporation |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation. |
| * |
| * Maintained by: Eilon Greenstein <eilong@broadcom.com> |
| * Written by: Eliezer Tamir |
| * Based on code from Michael Chan's bnx2 driver |
| * UDP CSUM errata workaround by Arik Gendelman |
| * Slowpath and fastpath rework by Vladislav Zolotarov |
| * Statistics and Link management by Yitchak Gertner |
| * |
| */ |
| |
| #include <linux/module.h> |
| #include <linux/moduleparam.h> |
| #include <linux/kernel.h> |
| #include <linux/device.h> /* for dev_info() */ |
| #include <linux/timer.h> |
| #include <linux/errno.h> |
| #include <linux/ioport.h> |
| #include <linux/slab.h> |
| #include <linux/vmalloc.h> |
| #include <linux/interrupt.h> |
| #include <linux/pci.h> |
| #include <linux/init.h> |
| #include <linux/netdevice.h> |
| #include <linux/etherdevice.h> |
| #include <linux/skbuff.h> |
| #include <linux/dma-mapping.h> |
| #include <linux/bitops.h> |
| #include <linux/irq.h> |
| #include <linux/delay.h> |
| #include <asm/byteorder.h> |
| #include <linux/time.h> |
| #include <linux/ethtool.h> |
| #include <linux/mii.h> |
| #include <linux/if_vlan.h> |
| #include <net/ip.h> |
| #include <net/tcp.h> |
| #include <net/checksum.h> |
| #include <net/ip6_checksum.h> |
| #include <linux/workqueue.h> |
| #include <linux/crc32.h> |
| #include <linux/crc32c.h> |
| #include <linux/prefetch.h> |
| #include <linux/zlib.h> |
| #include <linux/io.h> |
| #include <linux/stringify.h> |
| |
| #define BNX2X_MAIN |
| #include "bnx2x.h" |
| #include "bnx2x_init.h" |
| #include "bnx2x_init_ops.h" |
| #include "bnx2x_cmn.h" |
| |
| |
| #include <linux/firmware.h> |
| #include "bnx2x_fw_file_hdr.h" |
| /* FW files */ |
| #define FW_FILE_VERSION \ |
| __stringify(BCM_5710_FW_MAJOR_VERSION) "." \ |
| __stringify(BCM_5710_FW_MINOR_VERSION) "." \ |
| __stringify(BCM_5710_FW_REVISION_VERSION) "." \ |
| __stringify(BCM_5710_FW_ENGINEERING_VERSION) |
| #define FW_FILE_NAME_E1 "bnx2x-e1-" FW_FILE_VERSION ".fw" |
| #define FW_FILE_NAME_E1H "bnx2x-e1h-" FW_FILE_VERSION ".fw" |
| |
| /* Time in jiffies before concluding the transmitter is hung */ |
| #define TX_TIMEOUT (5*HZ) |
| |
| static char version[] __devinitdata = |
| "Broadcom NetXtreme II 5771x 10Gigabit Ethernet Driver " |
| DRV_MODULE_NAME " " DRV_MODULE_VERSION " (" DRV_MODULE_RELDATE ")\n"; |
| |
| MODULE_AUTHOR("Eliezer Tamir"); |
| MODULE_DESCRIPTION("Broadcom NetXtreme II BCM57710/57711/57711E Driver"); |
| MODULE_LICENSE("GPL"); |
| MODULE_VERSION(DRV_MODULE_VERSION); |
| MODULE_FIRMWARE(FW_FILE_NAME_E1); |
| MODULE_FIRMWARE(FW_FILE_NAME_E1H); |
| |
| static int multi_mode = 1; |
| module_param(multi_mode, int, 0); |
| MODULE_PARM_DESC(multi_mode, " Multi queue mode " |
| "(0 Disable; 1 Enable (default))"); |
| |
| static int num_queues; |
| module_param(num_queues, int, 0); |
| MODULE_PARM_DESC(num_queues, " Number of queues for multi_mode=1" |
| " (default is as a number of CPUs)"); |
| |
| static int disable_tpa; |
| module_param(disable_tpa, int, 0); |
| MODULE_PARM_DESC(disable_tpa, " Disable the TPA (LRO) feature"); |
| |
| static int int_mode; |
| module_param(int_mode, int, 0); |
| MODULE_PARM_DESC(int_mode, " Force interrupt mode other then MSI-X " |
| "(1 INT#x; 2 MSI)"); |
| |
| static int dropless_fc; |
| module_param(dropless_fc, int, 0); |
| MODULE_PARM_DESC(dropless_fc, " Pause on exhausted host ring"); |
| |
| static int poll; |
| module_param(poll, int, 0); |
| MODULE_PARM_DESC(poll, " Use polling (for debug)"); |
| |
| static int mrrs = -1; |
| module_param(mrrs, int, 0); |
| MODULE_PARM_DESC(mrrs, " Force Max Read Req Size (0..3) (for debug)"); |
| |
| static int debug; |
| module_param(debug, int, 0); |
| MODULE_PARM_DESC(debug, " Default debug msglevel"); |
| |
| static struct workqueue_struct *bnx2x_wq; |
| |
| enum bnx2x_board_type { |
| BCM57710 = 0, |
| BCM57711 = 1, |
| BCM57711E = 2, |
| }; |
| |
| /* indexed by board_type, above */ |
| static struct { |
| char *name; |
| } board_info[] __devinitdata = { |
| { "Broadcom NetXtreme II BCM57710 XGb" }, |
| { "Broadcom NetXtreme II BCM57711 XGb" }, |
| { "Broadcom NetXtreme II BCM57711E XGb" } |
| }; |
| |
| |
| static DEFINE_PCI_DEVICE_TABLE(bnx2x_pci_tbl) = { |
| { PCI_VDEVICE(BROADCOM, PCI_DEVICE_ID_NX2_57710), BCM57710 }, |
| { PCI_VDEVICE(BROADCOM, PCI_DEVICE_ID_NX2_57711), BCM57711 }, |
| { PCI_VDEVICE(BROADCOM, PCI_DEVICE_ID_NX2_57711E), BCM57711E }, |
| { 0 } |
| }; |
| |
| MODULE_DEVICE_TABLE(pci, bnx2x_pci_tbl); |
| |
| /**************************************************************************** |
| * General service functions |
| ****************************************************************************/ |
| |
| /* used only at init |
| * locking is done by mcp |
| */ |
| void bnx2x_reg_wr_ind(struct bnx2x *bp, u32 addr, u32 val) |
| { |
| pci_write_config_dword(bp->pdev, PCICFG_GRC_ADDRESS, addr); |
| pci_write_config_dword(bp->pdev, PCICFG_GRC_DATA, val); |
| pci_write_config_dword(bp->pdev, PCICFG_GRC_ADDRESS, |
| PCICFG_VENDOR_ID_OFFSET); |
| } |
| |
| static u32 bnx2x_reg_rd_ind(struct bnx2x *bp, u32 addr) |
| { |
| u32 val; |
| |
| pci_write_config_dword(bp->pdev, PCICFG_GRC_ADDRESS, addr); |
| pci_read_config_dword(bp->pdev, PCICFG_GRC_DATA, &val); |
| pci_write_config_dword(bp->pdev, PCICFG_GRC_ADDRESS, |
| PCICFG_VENDOR_ID_OFFSET); |
| |
| return val; |
| } |
| |
| const u32 dmae_reg_go_c[] = { |
| DMAE_REG_GO_C0, DMAE_REG_GO_C1, DMAE_REG_GO_C2, DMAE_REG_GO_C3, |
| DMAE_REG_GO_C4, DMAE_REG_GO_C5, DMAE_REG_GO_C6, DMAE_REG_GO_C7, |
| DMAE_REG_GO_C8, DMAE_REG_GO_C9, DMAE_REG_GO_C10, DMAE_REG_GO_C11, |
| DMAE_REG_GO_C12, DMAE_REG_GO_C13, DMAE_REG_GO_C14, DMAE_REG_GO_C15 |
| }; |
| |
| /* copy command into DMAE command memory and set DMAE command go */ |
| void bnx2x_post_dmae(struct bnx2x *bp, struct dmae_command *dmae, int idx) |
| { |
| u32 cmd_offset; |
| int i; |
| |
| cmd_offset = (DMAE_REG_CMD_MEM + sizeof(struct dmae_command) * idx); |
| for (i = 0; i < (sizeof(struct dmae_command)/4); i++) { |
| REG_WR(bp, cmd_offset + i*4, *(((u32 *)dmae) + i)); |
| |
| DP(BNX2X_MSG_OFF, "DMAE cmd[%d].%d (0x%08x) : 0x%08x\n", |
| idx, i, cmd_offset + i*4, *(((u32 *)dmae) + i)); |
| } |
| REG_WR(bp, dmae_reg_go_c[idx], 1); |
| } |
| |
| void bnx2x_write_dmae(struct bnx2x *bp, dma_addr_t dma_addr, u32 dst_addr, |
| u32 len32) |
| { |
| struct dmae_command dmae; |
| u32 *wb_comp = bnx2x_sp(bp, wb_comp); |
| int cnt = 200; |
| |
| if (!bp->dmae_ready) { |
| u32 *data = bnx2x_sp(bp, wb_data[0]); |
| |
| DP(BNX2X_MSG_OFF, "DMAE is not ready (dst_addr %08x len32 %d)" |
| " using indirect\n", dst_addr, len32); |
| bnx2x_init_ind_wr(bp, dst_addr, data, len32); |
| return; |
| } |
| |
| memset(&dmae, 0, sizeof(struct dmae_command)); |
| |
| dmae.opcode = (DMAE_CMD_SRC_PCI | DMAE_CMD_DST_GRC | |
| DMAE_CMD_C_DST_PCI | DMAE_CMD_C_ENABLE | |
| DMAE_CMD_SRC_RESET | DMAE_CMD_DST_RESET | |
| #ifdef __BIG_ENDIAN |
| DMAE_CMD_ENDIANITY_B_DW_SWAP | |
| #else |
| DMAE_CMD_ENDIANITY_DW_SWAP | |
| #endif |
| (BP_PORT(bp) ? DMAE_CMD_PORT_1 : DMAE_CMD_PORT_0) | |
| (BP_E1HVN(bp) << DMAE_CMD_E1HVN_SHIFT)); |
| dmae.src_addr_lo = U64_LO(dma_addr); |
| dmae.src_addr_hi = U64_HI(dma_addr); |
| dmae.dst_addr_lo = dst_addr >> 2; |
| dmae.dst_addr_hi = 0; |
| dmae.len = len32; |
| dmae.comp_addr_lo = U64_LO(bnx2x_sp_mapping(bp, wb_comp)); |
| dmae.comp_addr_hi = U64_HI(bnx2x_sp_mapping(bp, wb_comp)); |
| dmae.comp_val = DMAE_COMP_VAL; |
| |
| DP(BNX2X_MSG_OFF, "DMAE: opcode 0x%08x\n" |
| DP_LEVEL "src_addr [%x:%08x] len [%d *4] " |
| "dst_addr [%x:%08x (%08x)]\n" |
| DP_LEVEL "comp_addr [%x:%08x] comp_val 0x%08x\n", |
| dmae.opcode, dmae.src_addr_hi, dmae.src_addr_lo, |
| dmae.len, dmae.dst_addr_hi, dmae.dst_addr_lo, dst_addr, |
| dmae.comp_addr_hi, dmae.comp_addr_lo, dmae.comp_val); |
| DP(BNX2X_MSG_OFF, "data [0x%08x 0x%08x 0x%08x 0x%08x]\n", |
| bp->slowpath->wb_data[0], bp->slowpath->wb_data[1], |
| bp->slowpath->wb_data[2], bp->slowpath->wb_data[3]); |
| |
| mutex_lock(&bp->dmae_mutex); |
| |
| *wb_comp = 0; |
| |
| bnx2x_post_dmae(bp, &dmae, INIT_DMAE_C(bp)); |
| |
| udelay(5); |
| |
| while (*wb_comp != DMAE_COMP_VAL) { |
| DP(BNX2X_MSG_OFF, "wb_comp 0x%08x\n", *wb_comp); |
| |
| if (!cnt) { |
| BNX2X_ERR("DMAE timeout!\n"); |
| break; |
| } |
| cnt--; |
| /* adjust delay for emulation/FPGA */ |
| if (CHIP_REV_IS_SLOW(bp)) |
| msleep(100); |
| else |
| udelay(5); |
| } |
| |
| mutex_unlock(&bp->dmae_mutex); |
| } |
| |
| void bnx2x_read_dmae(struct bnx2x *bp, u32 src_addr, u32 len32) |
| { |
| struct dmae_command dmae; |
| u32 *wb_comp = bnx2x_sp(bp, wb_comp); |
| int cnt = 200; |
| |
| if (!bp->dmae_ready) { |
| u32 *data = bnx2x_sp(bp, wb_data[0]); |
| int i; |
| |
| DP(BNX2X_MSG_OFF, "DMAE is not ready (src_addr %08x len32 %d)" |
| " using indirect\n", src_addr, len32); |
| for (i = 0; i < len32; i++) |
| data[i] = bnx2x_reg_rd_ind(bp, src_addr + i*4); |
| return; |
| } |
| |
| memset(&dmae, 0, sizeof(struct dmae_command)); |
| |
| dmae.opcode = (DMAE_CMD_SRC_GRC | DMAE_CMD_DST_PCI | |
| DMAE_CMD_C_DST_PCI | DMAE_CMD_C_ENABLE | |
| DMAE_CMD_SRC_RESET | DMAE_CMD_DST_RESET | |
| #ifdef __BIG_ENDIAN |
| DMAE_CMD_ENDIANITY_B_DW_SWAP | |
| #else |
| DMAE_CMD_ENDIANITY_DW_SWAP | |
| #endif |
| (BP_PORT(bp) ? DMAE_CMD_PORT_1 : DMAE_CMD_PORT_0) | |
| (BP_E1HVN(bp) << DMAE_CMD_E1HVN_SHIFT)); |
| dmae.src_addr_lo = src_addr >> 2; |
| dmae.src_addr_hi = 0; |
| dmae.dst_addr_lo = U64_LO(bnx2x_sp_mapping(bp, wb_data)); |
| dmae.dst_addr_hi = U64_HI(bnx2x_sp_mapping(bp, wb_data)); |
| dmae.len = len32; |
| dmae.comp_addr_lo = U64_LO(bnx2x_sp_mapping(bp, wb_comp)); |
| dmae.comp_addr_hi = U64_HI(bnx2x_sp_mapping(bp, wb_comp)); |
| dmae.comp_val = DMAE_COMP_VAL; |
| |
| DP(BNX2X_MSG_OFF, "DMAE: opcode 0x%08x\n" |
| DP_LEVEL "src_addr [%x:%08x] len [%d *4] " |
| "dst_addr [%x:%08x (%08x)]\n" |
| DP_LEVEL "comp_addr [%x:%08x] comp_val 0x%08x\n", |
| dmae.opcode, dmae.src_addr_hi, dmae.src_addr_lo, |
| dmae.len, dmae.dst_addr_hi, dmae.dst_addr_lo, src_addr, |
| dmae.comp_addr_hi, dmae.comp_addr_lo, dmae.comp_val); |
| |
| mutex_lock(&bp->dmae_mutex); |
| |
| memset(bnx2x_sp(bp, wb_data[0]), 0, sizeof(u32) * 4); |
| *wb_comp = 0; |
| |
| bnx2x_post_dmae(bp, &dmae, INIT_DMAE_C(bp)); |
| |
| udelay(5); |
| |
| while (*wb_comp != DMAE_COMP_VAL) { |
| |
| if (!cnt) { |
| BNX2X_ERR("DMAE timeout!\n"); |
| break; |
| } |
| cnt--; |
| /* adjust delay for emulation/FPGA */ |
| if (CHIP_REV_IS_SLOW(bp)) |
| msleep(100); |
| else |
| udelay(5); |
| } |
| DP(BNX2X_MSG_OFF, "data [0x%08x 0x%08x 0x%08x 0x%08x]\n", |
| bp->slowpath->wb_data[0], bp->slowpath->wb_data[1], |
| bp->slowpath->wb_data[2], bp->slowpath->wb_data[3]); |
| |
| mutex_unlock(&bp->dmae_mutex); |
| } |
| |
| void bnx2x_write_dmae_phys_len(struct bnx2x *bp, dma_addr_t phys_addr, |
| u32 addr, u32 len) |
| { |
| int dmae_wr_max = DMAE_LEN32_WR_MAX(bp); |
| int offset = 0; |
| |
| while (len > dmae_wr_max) { |
| bnx2x_write_dmae(bp, phys_addr + offset, |
| addr + offset, dmae_wr_max); |
| offset += dmae_wr_max * 4; |
| len -= dmae_wr_max; |
| } |
| |
| bnx2x_write_dmae(bp, phys_addr + offset, addr + offset, len); |
| } |
| |
| /* used only for slowpath so not inlined */ |
| static void bnx2x_wb_wr(struct bnx2x *bp, int reg, u32 val_hi, u32 val_lo) |
| { |
| u32 wb_write[2]; |
| |
| wb_write[0] = val_hi; |
| wb_write[1] = val_lo; |
| REG_WR_DMAE(bp, reg, wb_write, 2); |
| } |
| |
| #ifdef USE_WB_RD |
| static u64 bnx2x_wb_rd(struct bnx2x *bp, int reg) |
| { |
| u32 wb_data[2]; |
| |
| REG_RD_DMAE(bp, reg, wb_data, 2); |
| |
| return HILO_U64(wb_data[0], wb_data[1]); |
| } |
| #endif |
| |
| static int bnx2x_mc_assert(struct bnx2x *bp) |
| { |
| char last_idx; |
| int i, rc = 0; |
| u32 row0, row1, row2, row3; |
| |
| /* XSTORM */ |
| last_idx = REG_RD8(bp, BAR_XSTRORM_INTMEM + |
| XSTORM_ASSERT_LIST_INDEX_OFFSET); |
| if (last_idx) |
| BNX2X_ERR("XSTORM_ASSERT_LIST_INDEX 0x%x\n", last_idx); |
| |
| /* print the asserts */ |
| for (i = 0; i < STROM_ASSERT_ARRAY_SIZE; i++) { |
| |
| row0 = REG_RD(bp, BAR_XSTRORM_INTMEM + |
| XSTORM_ASSERT_LIST_OFFSET(i)); |
| row1 = REG_RD(bp, BAR_XSTRORM_INTMEM + |
| XSTORM_ASSERT_LIST_OFFSET(i) + 4); |
| row2 = REG_RD(bp, BAR_XSTRORM_INTMEM + |
| XSTORM_ASSERT_LIST_OFFSET(i) + 8); |
| row3 = REG_RD(bp, BAR_XSTRORM_INTMEM + |
| XSTORM_ASSERT_LIST_OFFSET(i) + 12); |
| |
| if (row0 != COMMON_ASM_INVALID_ASSERT_OPCODE) { |
| BNX2X_ERR("XSTORM_ASSERT_INDEX 0x%x = 0x%08x" |
| " 0x%08x 0x%08x 0x%08x\n", |
| i, row3, row2, row1, row0); |
| rc++; |
| } else { |
| break; |
| } |
| } |
| |
| /* TSTORM */ |
| last_idx = REG_RD8(bp, BAR_TSTRORM_INTMEM + |
| TSTORM_ASSERT_LIST_INDEX_OFFSET); |
| if (last_idx) |
| BNX2X_ERR("TSTORM_ASSERT_LIST_INDEX 0x%x\n", last_idx); |
| |
| /* print the asserts */ |
| for (i = 0; i < STROM_ASSERT_ARRAY_SIZE; i++) { |
| |
| row0 = REG_RD(bp, BAR_TSTRORM_INTMEM + |
| TSTORM_ASSERT_LIST_OFFSET(i)); |
| row1 = REG_RD(bp, BAR_TSTRORM_INTMEM + |
| TSTORM_ASSERT_LIST_OFFSET(i) + 4); |
| row2 = REG_RD(bp, BAR_TSTRORM_INTMEM + |
| TSTORM_ASSERT_LIST_OFFSET(i) + 8); |
| row3 = REG_RD(bp, BAR_TSTRORM_INTMEM + |
| TSTORM_ASSERT_LIST_OFFSET(i) + 12); |
| |
| if (row0 != COMMON_ASM_INVALID_ASSERT_OPCODE) { |
| BNX2X_ERR("TSTORM_ASSERT_INDEX 0x%x = 0x%08x" |
| " 0x%08x 0x%08x 0x%08x\n", |
| i, row3, row2, row1, row0); |
| rc++; |
| } else { |
| break; |
| } |
| } |
| |
| /* CSTORM */ |
| last_idx = REG_RD8(bp, BAR_CSTRORM_INTMEM + |
| CSTORM_ASSERT_LIST_INDEX_OFFSET); |
| if (last_idx) |
| BNX2X_ERR("CSTORM_ASSERT_LIST_INDEX 0x%x\n", last_idx); |
| |
| /* print the asserts */ |
| for (i = 0; i < STROM_ASSERT_ARRAY_SIZE; i++) { |
| |
| row0 = REG_RD(bp, BAR_CSTRORM_INTMEM + |
| CSTORM_ASSERT_LIST_OFFSET(i)); |
| row1 = REG_RD(bp, BAR_CSTRORM_INTMEM + |
| CSTORM_ASSERT_LIST_OFFSET(i) + 4); |
| row2 = REG_RD(bp, BAR_CSTRORM_INTMEM + |
| CSTORM_ASSERT_LIST_OFFSET(i) + 8); |
| row3 = REG_RD(bp, BAR_CSTRORM_INTMEM + |
| CSTORM_ASSERT_LIST_OFFSET(i) + 12); |
| |
| if (row0 != COMMON_ASM_INVALID_ASSERT_OPCODE) { |
| BNX2X_ERR("CSTORM_ASSERT_INDEX 0x%x = 0x%08x" |
| " 0x%08x 0x%08x 0x%08x\n", |
| i, row3, row2, row1, row0); |
| rc++; |
| } else { |
| break; |
| } |
| } |
| |
| /* USTORM */ |
| last_idx = REG_RD8(bp, BAR_USTRORM_INTMEM + |
| USTORM_ASSERT_LIST_INDEX_OFFSET); |
| if (last_idx) |
| BNX2X_ERR("USTORM_ASSERT_LIST_INDEX 0x%x\n", last_idx); |
| |
| /* print the asserts */ |
| for (i = 0; i < STROM_ASSERT_ARRAY_SIZE; i++) { |
| |
| row0 = REG_RD(bp, BAR_USTRORM_INTMEM + |
| USTORM_ASSERT_LIST_OFFSET(i)); |
| row1 = REG_RD(bp, BAR_USTRORM_INTMEM + |
| USTORM_ASSERT_LIST_OFFSET(i) + 4); |
| row2 = REG_RD(bp, BAR_USTRORM_INTMEM + |
| USTORM_ASSERT_LIST_OFFSET(i) + 8); |
| row3 = REG_RD(bp, BAR_USTRORM_INTMEM + |
| USTORM_ASSERT_LIST_OFFSET(i) + 12); |
| |
| if (row0 != COMMON_ASM_INVALID_ASSERT_OPCODE) { |
| BNX2X_ERR("USTORM_ASSERT_INDEX 0x%x = 0x%08x" |
| " 0x%08x 0x%08x 0x%08x\n", |
| i, row3, row2, row1, row0); |
| rc++; |
| } else { |
| break; |
| } |
| } |
| |
| return rc; |
| } |
| |
| static void bnx2x_fw_dump(struct bnx2x *bp) |
| { |
| u32 addr; |
| u32 mark, offset; |
| __be32 data[9]; |
| int word; |
| |
| if (BP_NOMCP(bp)) { |
| BNX2X_ERR("NO MCP - can not dump\n"); |
| return; |
| } |
| |
| addr = bp->common.shmem_base - 0x0800 + 4; |
| mark = REG_RD(bp, addr); |
| mark = MCP_REG_MCPR_SCRATCH + ((mark + 0x3) & ~0x3) - 0x08000000; |
| pr_err("begin fw dump (mark 0x%x)\n", mark); |
| |
| pr_err(""); |
| for (offset = mark; offset <= bp->common.shmem_base; offset += 0x8*4) { |
| for (word = 0; word < 8; word++) |
| data[word] = htonl(REG_RD(bp, offset + 4*word)); |
| data[8] = 0x0; |
| pr_cont("%s", (char *)data); |
| } |
| for (offset = addr + 4; offset <= mark; offset += 0x8*4) { |
| for (word = 0; word < 8; word++) |
| data[word] = htonl(REG_RD(bp, offset + 4*word)); |
| data[8] = 0x0; |
| pr_cont("%s", (char *)data); |
| } |
| pr_err("end of fw dump\n"); |
| } |
| |
| void bnx2x_panic_dump(struct bnx2x *bp) |
| { |
| int i; |
| u16 j, start, end; |
| |
| bp->stats_state = STATS_STATE_DISABLED; |
| DP(BNX2X_MSG_STATS, "stats_state - DISABLED\n"); |
| |
| BNX2X_ERR("begin crash dump -----------------\n"); |
| |
| /* Indices */ |
| /* Common */ |
| BNX2X_ERR("def_c_idx(0x%x) def_u_idx(0x%x) def_x_idx(0x%x)" |
| " def_t_idx(0x%x) def_att_idx(0x%x) attn_state(0x%x)" |
| " spq_prod_idx(0x%x)\n", |
| bp->def_c_idx, bp->def_u_idx, bp->def_x_idx, bp->def_t_idx, |
| bp->def_att_idx, bp->attn_state, bp->spq_prod_idx); |
| |
| /* Rx */ |
| for_each_queue(bp, i) { |
| struct bnx2x_fastpath *fp = &bp->fp[i]; |
| |
| BNX2X_ERR("fp%d: rx_bd_prod(0x%x) rx_bd_cons(0x%x)" |
| " *rx_bd_cons_sb(0x%x) rx_comp_prod(0x%x)" |
| " rx_comp_cons(0x%x) *rx_cons_sb(0x%x)\n", |
| i, fp->rx_bd_prod, fp->rx_bd_cons, |
| le16_to_cpu(*fp->rx_bd_cons_sb), fp->rx_comp_prod, |
| fp->rx_comp_cons, le16_to_cpu(*fp->rx_cons_sb)); |
| BNX2X_ERR(" rx_sge_prod(0x%x) last_max_sge(0x%x)" |
| " fp_u_idx(0x%x) *sb_u_idx(0x%x)\n", |
| fp->rx_sge_prod, fp->last_max_sge, |
| le16_to_cpu(fp->fp_u_idx), |
| fp->status_blk->u_status_block.status_block_index); |
| } |
| |
| /* Tx */ |
| for_each_queue(bp, i) { |
| struct bnx2x_fastpath *fp = &bp->fp[i]; |
| |
| BNX2X_ERR("fp%d: tx_pkt_prod(0x%x) tx_pkt_cons(0x%x)" |
| " tx_bd_prod(0x%x) tx_bd_cons(0x%x)" |
| " *tx_cons_sb(0x%x)\n", |
| i, fp->tx_pkt_prod, fp->tx_pkt_cons, fp->tx_bd_prod, |
| fp->tx_bd_cons, le16_to_cpu(*fp->tx_cons_sb)); |
| BNX2X_ERR(" fp_c_idx(0x%x) *sb_c_idx(0x%x)" |
| " tx_db_prod(0x%x)\n", le16_to_cpu(fp->fp_c_idx), |
| fp->status_blk->c_status_block.status_block_index, |
| fp->tx_db.data.prod); |
| } |
| |
| /* Rings */ |
| /* Rx */ |
| for_each_queue(bp, i) { |
| struct bnx2x_fastpath *fp = &bp->fp[i]; |
| |
| start = RX_BD(le16_to_cpu(*fp->rx_cons_sb) - 10); |
| end = RX_BD(le16_to_cpu(*fp->rx_cons_sb) + 503); |
| for (j = start; j != end; j = RX_BD(j + 1)) { |
| u32 *rx_bd = (u32 *)&fp->rx_desc_ring[j]; |
| struct sw_rx_bd *sw_bd = &fp->rx_buf_ring[j]; |
| |
| BNX2X_ERR("fp%d: rx_bd[%x]=[%x:%x] sw_bd=[%p]\n", |
| i, j, rx_bd[1], rx_bd[0], sw_bd->skb); |
| } |
| |
| start = RX_SGE(fp->rx_sge_prod); |
| end = RX_SGE(fp->last_max_sge); |
| for (j = start; j != end; j = RX_SGE(j + 1)) { |
| u32 *rx_sge = (u32 *)&fp->rx_sge_ring[j]; |
| struct sw_rx_page *sw_page = &fp->rx_page_ring[j]; |
| |
| BNX2X_ERR("fp%d: rx_sge[%x]=[%x:%x] sw_page=[%p]\n", |
| i, j, rx_sge[1], rx_sge[0], sw_page->page); |
| } |
| |
| start = RCQ_BD(fp->rx_comp_cons - 10); |
| end = RCQ_BD(fp->rx_comp_cons + 503); |
| for (j = start; j != end; j = RCQ_BD(j + 1)) { |
| u32 *cqe = (u32 *)&fp->rx_comp_ring[j]; |
| |
| BNX2X_ERR("fp%d: cqe[%x]=[%x:%x:%x:%x]\n", |
| i, j, cqe[0], cqe[1], cqe[2], cqe[3]); |
| } |
| } |
| |
| /* Tx */ |
| for_each_queue(bp, i) { |
| struct bnx2x_fastpath *fp = &bp->fp[i]; |
| |
| start = TX_BD(le16_to_cpu(*fp->tx_cons_sb) - 10); |
| end = TX_BD(le16_to_cpu(*fp->tx_cons_sb) + 245); |
| for (j = start; j != end; j = TX_BD(j + 1)) { |
| struct sw_tx_bd *sw_bd = &fp->tx_buf_ring[j]; |
| |
| BNX2X_ERR("fp%d: packet[%x]=[%p,%x]\n", |
| i, j, sw_bd->skb, sw_bd->first_bd); |
| } |
| |
| start = TX_BD(fp->tx_bd_cons - 10); |
| end = TX_BD(fp->tx_bd_cons + 254); |
| for (j = start; j != end; j = TX_BD(j + 1)) { |
| u32 *tx_bd = (u32 *)&fp->tx_desc_ring[j]; |
| |
| BNX2X_ERR("fp%d: tx_bd[%x]=[%x:%x:%x:%x]\n", |
| i, j, tx_bd[0], tx_bd[1], tx_bd[2], tx_bd[3]); |
| } |
| } |
| |
| bnx2x_fw_dump(bp); |
| bnx2x_mc_assert(bp); |
| BNX2X_ERR("end crash dump -----------------\n"); |
| } |
| |
| void bnx2x_int_enable(struct bnx2x *bp) |
| { |
| int port = BP_PORT(bp); |
| u32 addr = port ? HC_REG_CONFIG_1 : HC_REG_CONFIG_0; |
| u32 val = REG_RD(bp, addr); |
| int msix = (bp->flags & USING_MSIX_FLAG) ? 1 : 0; |
| int msi = (bp->flags & USING_MSI_FLAG) ? 1 : 0; |
| |
| if (msix) { |
| val &= ~(HC_CONFIG_0_REG_SINGLE_ISR_EN_0 | |
| HC_CONFIG_0_REG_INT_LINE_EN_0); |
| val |= (HC_CONFIG_0_REG_MSI_MSIX_INT_EN_0 | |
| HC_CONFIG_0_REG_ATTN_BIT_EN_0); |
| } else if (msi) { |
| val &= ~HC_CONFIG_0_REG_INT_LINE_EN_0; |
| val |= (HC_CONFIG_0_REG_SINGLE_ISR_EN_0 | |
| HC_CONFIG_0_REG_MSI_MSIX_INT_EN_0 | |
| HC_CONFIG_0_REG_ATTN_BIT_EN_0); |
| } else { |
| val |= (HC_CONFIG_0_REG_SINGLE_ISR_EN_0 | |
| HC_CONFIG_0_REG_MSI_MSIX_INT_EN_0 | |
| HC_CONFIG_0_REG_INT_LINE_EN_0 | |
| HC_CONFIG_0_REG_ATTN_BIT_EN_0); |
| |
| DP(NETIF_MSG_INTR, "write %x to HC %d (addr 0x%x)\n", |
| val, port, addr); |
| |
| REG_WR(bp, addr, val); |
| |
| val &= ~HC_CONFIG_0_REG_MSI_MSIX_INT_EN_0; |
| } |
| |
| DP(NETIF_MSG_INTR, "write %x to HC %d (addr 0x%x) mode %s\n", |
| val, port, addr, (msix ? "MSI-X" : (msi ? "MSI" : "INTx"))); |
| |
| REG_WR(bp, addr, val); |
| /* |
| * Ensure that HC_CONFIG is written before leading/trailing edge config |
| */ |
| mmiowb(); |
| barrier(); |
| |
| if (CHIP_IS_E1H(bp)) { |
| /* init leading/trailing edge */ |
| if (IS_E1HMF(bp)) { |
| val = (0xee0f | (1 << (BP_E1HVN(bp) + 4))); |
| if (bp->port.pmf) |
| /* enable nig and gpio3 attention */ |
| val |= 0x1100; |
| } else |
| val = 0xffff; |
| |
| REG_WR(bp, HC_REG_TRAILING_EDGE_0 + port*8, val); |
| REG_WR(bp, HC_REG_LEADING_EDGE_0 + port*8, val); |
| } |
| |
| /* Make sure that interrupts are indeed enabled from here on */ |
| mmiowb(); |
| } |
| |
| static void bnx2x_int_disable(struct bnx2x *bp) |
| { |
| int port = BP_PORT(bp); |
| u32 addr = port ? HC_REG_CONFIG_1 : HC_REG_CONFIG_0; |
| u32 val = REG_RD(bp, addr); |
| |
| val &= ~(HC_CONFIG_0_REG_SINGLE_ISR_EN_0 | |
| HC_CONFIG_0_REG_MSI_MSIX_INT_EN_0 | |
| HC_CONFIG_0_REG_INT_LINE_EN_0 | |
| HC_CONFIG_0_REG_ATTN_BIT_EN_0); |
| |
| DP(NETIF_MSG_INTR, "write %x to HC %d (addr 0x%x)\n", |
| val, port, addr); |
| |
| /* flush all outstanding writes */ |
| mmiowb(); |
| |
| REG_WR(bp, addr, val); |
| if (REG_RD(bp, addr) != val) |
| BNX2X_ERR("BUG! proper val not read from IGU!\n"); |
| } |
| |
| void bnx2x_int_disable_sync(struct bnx2x *bp, int disable_hw) |
| { |
| int msix = (bp->flags & USING_MSIX_FLAG) ? 1 : 0; |
| int i, offset; |
| |
| /* disable interrupt handling */ |
| atomic_inc(&bp->intr_sem); |
| smp_wmb(); /* Ensure that bp->intr_sem update is SMP-safe */ |
| |
| if (disable_hw) |
| /* prevent the HW from sending interrupts */ |
| bnx2x_int_disable(bp); |
| |
| /* make sure all ISRs are done */ |
| if (msix) { |
| synchronize_irq(bp->msix_table[0].vector); |
| offset = 1; |
| #ifdef BCM_CNIC |
| offset++; |
| #endif |
| for_each_queue(bp, i) |
| synchronize_irq(bp->msix_table[i + offset].vector); |
| } else |
| synchronize_irq(bp->pdev->irq); |
| |
| /* make sure sp_task is not running */ |
| cancel_delayed_work(&bp->sp_task); |
| flush_workqueue(bnx2x_wq); |
| } |
| |
| /* fast path */ |
| |
| /* |
| * General service functions |
| */ |
| |
| /* Return true if succeeded to acquire the lock */ |
| static bool bnx2x_trylock_hw_lock(struct bnx2x *bp, u32 resource) |
| { |
| u32 lock_status; |
| u32 resource_bit = (1 << resource); |
| int func = BP_FUNC(bp); |
| u32 hw_lock_control_reg; |
| |
| DP(NETIF_MSG_HW, "Trying to take a lock on resource %d\n", resource); |
| |
| /* Validating that the resource is within range */ |
| if (resource > HW_LOCK_MAX_RESOURCE_VALUE) { |
| DP(NETIF_MSG_HW, |
| "resource(0x%x) > HW_LOCK_MAX_RESOURCE_VALUE(0x%x)\n", |
| resource, HW_LOCK_MAX_RESOURCE_VALUE); |
| return false; |
| } |
| |
| if (func <= 5) |
| hw_lock_control_reg = (MISC_REG_DRIVER_CONTROL_1 + func*8); |
| else |
| hw_lock_control_reg = |
| (MISC_REG_DRIVER_CONTROL_7 + (func - 6)*8); |
| |
| /* Try to acquire the lock */ |
| REG_WR(bp, hw_lock_control_reg + 4, resource_bit); |
| lock_status = REG_RD(bp, hw_lock_control_reg); |
| if (lock_status & resource_bit) |
| return true; |
| |
| DP(NETIF_MSG_HW, "Failed to get a lock on resource %d\n", resource); |
| return false; |
| } |
| |
| |
| #ifdef BCM_CNIC |
| static void bnx2x_cnic_cfc_comp(struct bnx2x *bp, int cid); |
| #endif |
| |
| void bnx2x_sp_event(struct bnx2x_fastpath *fp, |
| union eth_rx_cqe *rr_cqe) |
| { |
| struct bnx2x *bp = fp->bp; |
| int cid = SW_CID(rr_cqe->ramrod_cqe.conn_and_cmd_data); |
| int command = CQE_CMD(rr_cqe->ramrod_cqe.conn_and_cmd_data); |
| |
| DP(BNX2X_MSG_SP, |
| "fp %d cid %d got ramrod #%d state is %x type is %d\n", |
| fp->index, cid, command, bp->state, |
| rr_cqe->ramrod_cqe.ramrod_type); |
| |
| bp->spq_left++; |
| |
| if (fp->index) { |
| switch (command | fp->state) { |
| case (RAMROD_CMD_ID_ETH_CLIENT_SETUP | |
| BNX2X_FP_STATE_OPENING): |
| DP(NETIF_MSG_IFUP, "got MULTI[%d] setup ramrod\n", |
| cid); |
| fp->state = BNX2X_FP_STATE_OPEN; |
| break; |
| |
| case (RAMROD_CMD_ID_ETH_HALT | BNX2X_FP_STATE_HALTING): |
| DP(NETIF_MSG_IFDOWN, "got MULTI[%d] halt ramrod\n", |
| cid); |
| fp->state = BNX2X_FP_STATE_HALTED; |
| break; |
| |
| default: |
| BNX2X_ERR("unexpected MC reply (%d) " |
| "fp[%d] state is %x\n", |
| command, fp->index, fp->state); |
| break; |
| } |
| mb(); /* force bnx2x_wait_ramrod() to see the change */ |
| return; |
| } |
| |
| switch (command | bp->state) { |
| case (RAMROD_CMD_ID_ETH_PORT_SETUP | BNX2X_STATE_OPENING_WAIT4_PORT): |
| DP(NETIF_MSG_IFUP, "got setup ramrod\n"); |
| bp->state = BNX2X_STATE_OPEN; |
| break; |
| |
| case (RAMROD_CMD_ID_ETH_HALT | BNX2X_STATE_CLOSING_WAIT4_HALT): |
| DP(NETIF_MSG_IFDOWN, "got halt ramrod\n"); |
| bp->state = BNX2X_STATE_CLOSING_WAIT4_DELETE; |
| fp->state = BNX2X_FP_STATE_HALTED; |
| break; |
| |
| case (RAMROD_CMD_ID_ETH_CFC_DEL | BNX2X_STATE_CLOSING_WAIT4_HALT): |
| DP(NETIF_MSG_IFDOWN, "got delete ramrod for MULTI[%d]\n", cid); |
| bnx2x_fp(bp, cid, state) = BNX2X_FP_STATE_CLOSED; |
| break; |
| |
| #ifdef BCM_CNIC |
| case (RAMROD_CMD_ID_ETH_CFC_DEL | BNX2X_STATE_OPEN): |
| DP(NETIF_MSG_IFDOWN, "got delete ramrod for CID %d\n", cid); |
| bnx2x_cnic_cfc_comp(bp, cid); |
| break; |
| #endif |
| |
| case (RAMROD_CMD_ID_ETH_SET_MAC | BNX2X_STATE_OPEN): |
| case (RAMROD_CMD_ID_ETH_SET_MAC | BNX2X_STATE_DIAG): |
| DP(NETIF_MSG_IFUP, "got set mac ramrod\n"); |
| bp->set_mac_pending--; |
| smp_wmb(); |
| break; |
| |
| case (RAMROD_CMD_ID_ETH_SET_MAC | BNX2X_STATE_CLOSING_WAIT4_HALT): |
| DP(NETIF_MSG_IFDOWN, "got (un)set mac ramrod\n"); |
| bp->set_mac_pending--; |
| smp_wmb(); |
| break; |
| |
| default: |
| BNX2X_ERR("unexpected MC reply (%d) bp->state is %x\n", |
| command, bp->state); |
| break; |
| } |
| mb(); /* force bnx2x_wait_ramrod() to see the change */ |
| } |
| |
| irqreturn_t bnx2x_interrupt(int irq, void *dev_instance) |
| { |
| struct bnx2x *bp = netdev_priv(dev_instance); |
| u16 status = bnx2x_ack_int(bp); |
| u16 mask; |
| int i; |
| |
| /* Return here if interrupt is shared and it's not for us */ |
| if (unlikely(status == 0)) { |
| DP(NETIF_MSG_INTR, "not our interrupt!\n"); |
| return IRQ_NONE; |
| } |
| DP(NETIF_MSG_INTR, "got an interrupt status 0x%x\n", status); |
| |
| /* Return here if interrupt is disabled */ |
| if (unlikely(atomic_read(&bp->intr_sem) != 0)) { |
| DP(NETIF_MSG_INTR, "called but intr_sem not 0, returning\n"); |
| return IRQ_HANDLED; |
| } |
| |
| #ifdef BNX2X_STOP_ON_ERROR |
| if (unlikely(bp->panic)) |
| return IRQ_HANDLED; |
| #endif |
| |
| for (i = 0; i < BNX2X_NUM_QUEUES(bp); i++) { |
| struct bnx2x_fastpath *fp = &bp->fp[i]; |
| |
| mask = 0x2 << fp->sb_id; |
| if (status & mask) { |
| /* Handle Rx and Tx according to SB id */ |
| prefetch(fp->rx_cons_sb); |
| prefetch(&fp->status_blk->u_status_block. |
| status_block_index); |
| prefetch(fp->tx_cons_sb); |
| prefetch(&fp->status_blk->c_status_block. |
| status_block_index); |
| napi_schedule(&bnx2x_fp(bp, fp->index, napi)); |
| status &= ~mask; |
| } |
| } |
| |
| #ifdef BCM_CNIC |
| mask = 0x2 << CNIC_SB_ID(bp); |
| if (status & (mask | 0x1)) { |
| struct cnic_ops *c_ops = NULL; |
| |
| rcu_read_lock(); |
| c_ops = rcu_dereference(bp->cnic_ops); |
| if (c_ops) |
| c_ops->cnic_handler(bp->cnic_data, NULL); |
| rcu_read_unlock(); |
| |
| status &= ~mask; |
| } |
| #endif |
| |
| if (unlikely(status & 0x1)) { |
| queue_delayed_work(bnx2x_wq, &bp->sp_task, 0); |
| |
| status &= ~0x1; |
| if (!status) |
| return IRQ_HANDLED; |
| } |
| |
| if (unlikely(status)) |
| DP(NETIF_MSG_INTR, "got an unknown interrupt! (status 0x%x)\n", |
| status); |
| |
| return IRQ_HANDLED; |
| } |
| |
| /* end of fast path */ |
| |
| |
| /* Link */ |
| |
| /* |
| * General service functions |
| */ |
| |
| int bnx2x_acquire_hw_lock(struct bnx2x *bp, u32 resource) |
| { |
| u32 lock_status; |
| u32 resource_bit = (1 << resource); |
| int func = BP_FUNC(bp); |
| u32 hw_lock_control_reg; |
| int cnt; |
| |
| /* Validating that the resource is within range */ |
| if (resource > HW_LOCK_MAX_RESOURCE_VALUE) { |
| DP(NETIF_MSG_HW, |
| "resource(0x%x) > HW_LOCK_MAX_RESOURCE_VALUE(0x%x)\n", |
| resource, HW_LOCK_MAX_RESOURCE_VALUE); |
| return -EINVAL; |
| } |
| |
| if (func <= 5) { |
| hw_lock_control_reg = (MISC_REG_DRIVER_CONTROL_1 + func*8); |
| } else { |
| hw_lock_control_reg = |
| (MISC_REG_DRIVER_CONTROL_7 + (func - 6)*8); |
| } |
| |
| /* Validating that the resource is not already taken */ |
| lock_status = REG_RD(bp, hw_lock_control_reg); |
| if (lock_status & resource_bit) { |
| DP(NETIF_MSG_HW, "lock_status 0x%x resource_bit 0x%x\n", |
| lock_status, resource_bit); |
| return -EEXIST; |
| } |
| |
| /* Try for 5 second every 5ms */ |
| for (cnt = 0; cnt < 1000; cnt++) { |
| /* Try to acquire the lock */ |
| REG_WR(bp, hw_lock_control_reg + 4, resource_bit); |
| lock_status = REG_RD(bp, hw_lock_control_reg); |
| if (lock_status & resource_bit) |
| return 0; |
| |
| msleep(5); |
| } |
| DP(NETIF_MSG_HW, "Timeout\n"); |
| return -EAGAIN; |
| } |
| |
| int bnx2x_release_hw_lock(struct bnx2x *bp, u32 resource) |
| { |
| u32 lock_status; |
| u32 resource_bit = (1 << resource); |
| int func = BP_FUNC(bp); |
| u32 hw_lock_control_reg; |
| |
| DP(NETIF_MSG_HW, "Releasing a lock on resource %d\n", resource); |
| |
| /* Validating that the resource is within range */ |
| if (resource > HW_LOCK_MAX_RESOURCE_VALUE) { |
| DP(NETIF_MSG_HW, |
| "resource(0x%x) > HW_LOCK_MAX_RESOURCE_VALUE(0x%x)\n", |
| resource, HW_LOCK_MAX_RESOURCE_VALUE); |
| return -EINVAL; |
| } |
| |
| if (func <= 5) { |
| hw_lock_control_reg = (MISC_REG_DRIVER_CONTROL_1 + func*8); |
| } else { |
| hw_lock_control_reg = |
| (MISC_REG_DRIVER_CONTROL_7 + (func - 6)*8); |
| } |
| |
| /* Validating that the resource is currently taken */ |
| lock_status = REG_RD(bp, hw_lock_control_reg); |
| if (!(lock_status & resource_bit)) { |
| DP(NETIF_MSG_HW, "lock_status 0x%x resource_bit 0x%x\n", |
| lock_status, resource_bit); |
| return -EFAULT; |
| } |
| |
| REG_WR(bp, hw_lock_control_reg, resource_bit); |
| return 0; |
| } |
| |
| |
| int bnx2x_get_gpio(struct bnx2x *bp, int gpio_num, u8 port) |
| { |
| /* The GPIO should be swapped if swap register is set and active */ |
| int gpio_port = (REG_RD(bp, NIG_REG_PORT_SWAP) && |
| REG_RD(bp, NIG_REG_STRAP_OVERRIDE)) ^ port; |
| int gpio_shift = gpio_num + |
| (gpio_port ? MISC_REGISTERS_GPIO_PORT_SHIFT : 0); |
| u32 gpio_mask = (1 << gpio_shift); |
| u32 gpio_reg; |
| int value; |
| |
| if (gpio_num > MISC_REGISTERS_GPIO_3) { |
| BNX2X_ERR("Invalid GPIO %d\n", gpio_num); |
| return -EINVAL; |
| } |
| |
| /* read GPIO value */ |
| gpio_reg = REG_RD(bp, MISC_REG_GPIO); |
| |
| /* get the requested pin value */ |
| if ((gpio_reg & gpio_mask) == gpio_mask) |
| value = 1; |
| else |
| value = 0; |
| |
| DP(NETIF_MSG_LINK, "pin %d value 0x%x\n", gpio_num, value); |
| |
| return value; |
| } |
| |
| int bnx2x_set_gpio(struct bnx2x *bp, int gpio_num, u32 mode, u8 port) |
| { |
| /* The GPIO should be swapped if swap register is set and active */ |
| int gpio_port = (REG_RD(bp, NIG_REG_PORT_SWAP) && |
| REG_RD(bp, NIG_REG_STRAP_OVERRIDE)) ^ port; |
| int gpio_shift = gpio_num + |
| (gpio_port ? MISC_REGISTERS_GPIO_PORT_SHIFT : 0); |
| u32 gpio_mask = (1 << gpio_shift); |
| u32 gpio_reg; |
| |
| if (gpio_num > MISC_REGISTERS_GPIO_3) { |
| BNX2X_ERR("Invalid GPIO %d\n", gpio_num); |
| return -EINVAL; |
| } |
| |
| bnx2x_acquire_hw_lock(bp, HW_LOCK_RESOURCE_GPIO); |
| /* read GPIO and mask except the float bits */ |
| gpio_reg = (REG_RD(bp, MISC_REG_GPIO) & MISC_REGISTERS_GPIO_FLOAT); |
| |
| switch (mode) { |
| case MISC_REGISTERS_GPIO_OUTPUT_LOW: |
| DP(NETIF_MSG_LINK, "Set GPIO %d (shift %d) -> output low\n", |
| gpio_num, gpio_shift); |
| /* clear FLOAT and set CLR */ |
| gpio_reg &= ~(gpio_mask << MISC_REGISTERS_GPIO_FLOAT_POS); |
| gpio_reg |= (gpio_mask << MISC_REGISTERS_GPIO_CLR_POS); |
| break; |
| |
| case MISC_REGISTERS_GPIO_OUTPUT_HIGH: |
| DP(NETIF_MSG_LINK, "Set GPIO %d (shift %d) -> output high\n", |
| gpio_num, gpio_shift); |
| /* clear FLOAT and set SET */ |
| gpio_reg &= ~(gpio_mask << MISC_REGISTERS_GPIO_FLOAT_POS); |
| gpio_reg |= (gpio_mask << MISC_REGISTERS_GPIO_SET_POS); |
| break; |
| |
| case MISC_REGISTERS_GPIO_INPUT_HI_Z: |
| DP(NETIF_MSG_LINK, "Set GPIO %d (shift %d) -> input\n", |
| gpio_num, gpio_shift); |
| /* set FLOAT */ |
| gpio_reg |= (gpio_mask << MISC_REGISTERS_GPIO_FLOAT_POS); |
| break; |
| |
| default: |
| break; |
| } |
| |
| REG_WR(bp, MISC_REG_GPIO, gpio_reg); |
| bnx2x_release_hw_lock(bp, HW_LOCK_RESOURCE_GPIO); |
| |
| return 0; |
| } |
| |
| int bnx2x_set_gpio_int(struct bnx2x *bp, int gpio_num, u32 mode, u8 port) |
| { |
| /* The GPIO should be swapped if swap register is set and active */ |
| int gpio_port = (REG_RD(bp, NIG_REG_PORT_SWAP) && |
| REG_RD(bp, NIG_REG_STRAP_OVERRIDE)) ^ port; |
| int gpio_shift = gpio_num + |
| (gpio_port ? MISC_REGISTERS_GPIO_PORT_SHIFT : 0); |
| u32 gpio_mask = (1 << gpio_shift); |
| u32 gpio_reg; |
| |
| if (gpio_num > MISC_REGISTERS_GPIO_3) { |
| BNX2X_ERR("Invalid GPIO %d\n", gpio_num); |
| return -EINVAL; |
| } |
| |
| bnx2x_acquire_hw_lock(bp, HW_LOCK_RESOURCE_GPIO); |
| /* read GPIO int */ |
| gpio_reg = REG_RD(bp, MISC_REG_GPIO_INT); |
| |
| switch (mode) { |
| case MISC_REGISTERS_GPIO_INT_OUTPUT_CLR: |
| DP(NETIF_MSG_LINK, "Clear GPIO INT %d (shift %d) -> " |
| "output low\n", gpio_num, gpio_shift); |
| /* clear SET and set CLR */ |
| gpio_reg &= ~(gpio_mask << MISC_REGISTERS_GPIO_INT_SET_POS); |
| gpio_reg |= (gpio_mask << MISC_REGISTERS_GPIO_INT_CLR_POS); |
| break; |
| |
| case MISC_REGISTERS_GPIO_INT_OUTPUT_SET: |
| DP(NETIF_MSG_LINK, "Set GPIO INT %d (shift %d) -> " |
| "output high\n", gpio_num, gpio_shift); |
| /* clear CLR and set SET */ |
| gpio_reg &= ~(gpio_mask << MISC_REGISTERS_GPIO_INT_CLR_POS); |
| gpio_reg |= (gpio_mask << MISC_REGISTERS_GPIO_INT_SET_POS); |
| break; |
| |
| default: |
| break; |
| } |
| |
| REG_WR(bp, MISC_REG_GPIO_INT, gpio_reg); |
| bnx2x_release_hw_lock(bp, HW_LOCK_RESOURCE_GPIO); |
| |
| return 0; |
| } |
| |
| static int bnx2x_set_spio(struct bnx2x *bp, int spio_num, u32 mode) |
| { |
| u32 spio_mask = (1 << spio_num); |
| u32 spio_reg; |
| |
| if ((spio_num < MISC_REGISTERS_SPIO_4) || |
| (spio_num > MISC_REGISTERS_SPIO_7)) { |
| BNX2X_ERR("Invalid SPIO %d\n", spio_num); |
| return -EINVAL; |
| } |
| |
| bnx2x_acquire_hw_lock(bp, HW_LOCK_RESOURCE_SPIO); |
| /* read SPIO and mask except the float bits */ |
| spio_reg = (REG_RD(bp, MISC_REG_SPIO) & MISC_REGISTERS_SPIO_FLOAT); |
| |
| switch (mode) { |
| case MISC_REGISTERS_SPIO_OUTPUT_LOW: |
| DP(NETIF_MSG_LINK, "Set SPIO %d -> output low\n", spio_num); |
| /* clear FLOAT and set CLR */ |
| spio_reg &= ~(spio_mask << MISC_REGISTERS_SPIO_FLOAT_POS); |
| spio_reg |= (spio_mask << MISC_REGISTERS_SPIO_CLR_POS); |
| break; |
| |
| case MISC_REGISTERS_SPIO_OUTPUT_HIGH: |
| DP(NETIF_MSG_LINK, "Set SPIO %d -> output high\n", spio_num); |
| /* clear FLOAT and set SET */ |
| spio_reg &= ~(spio_mask << MISC_REGISTERS_SPIO_FLOAT_POS); |
| spio_reg |= (spio_mask << MISC_REGISTERS_SPIO_SET_POS); |
| break; |
| |
| case MISC_REGISTERS_SPIO_INPUT_HI_Z: |
| DP(NETIF_MSG_LINK, "Set SPIO %d -> input\n", spio_num); |
| /* set FLOAT */ |
| spio_reg |= (spio_mask << MISC_REGISTERS_SPIO_FLOAT_POS); |
| break; |
| |
| default: |
| break; |
| } |
| |
| REG_WR(bp, MISC_REG_SPIO, spio_reg); |
| bnx2x_release_hw_lock(bp, HW_LOCK_RESOURCE_SPIO); |
| |
| return 0; |
| } |
| |
| int bnx2x_get_link_cfg_idx(struct bnx2x *bp) |
| { |
| u32 sel_phy_idx = 0; |
| if (bp->link_vars.link_up) { |
| sel_phy_idx = EXT_PHY1; |
| /* In case link is SERDES, check if the EXT_PHY2 is the one */ |
| if ((bp->link_vars.link_status & LINK_STATUS_SERDES_LINK) && |
| (bp->link_params.phy[EXT_PHY2].supported & SUPPORTED_FIBRE)) |
| sel_phy_idx = EXT_PHY2; |
| } else { |
| |
| switch (bnx2x_phy_selection(&bp->link_params)) { |
| case PORT_HW_CFG_PHY_SELECTION_HARDWARE_DEFAULT: |
| case PORT_HW_CFG_PHY_SELECTION_FIRST_PHY: |
| case PORT_HW_CFG_PHY_SELECTION_FIRST_PHY_PRIORITY: |
| sel_phy_idx = EXT_PHY1; |
| break; |
| case PORT_HW_CFG_PHY_SELECTION_SECOND_PHY: |
| case PORT_HW_CFG_PHY_SELECTION_SECOND_PHY_PRIORITY: |
| sel_phy_idx = EXT_PHY2; |
| break; |
| } |
| } |
| /* |
| * The selected actived PHY is always after swapping (in case PHY |
| * swapping is enabled). So when swapping is enabled, we need to reverse |
| * the configuration |
| */ |
| |
| if (bp->link_params.multi_phy_config & |
| PORT_HW_CFG_PHY_SWAPPED_ENABLED) { |
| if (sel_phy_idx == EXT_PHY1) |
| sel_phy_idx = EXT_PHY2; |
| else if (sel_phy_idx == EXT_PHY2) |
| sel_phy_idx = EXT_PHY1; |
| } |
| return LINK_CONFIG_IDX(sel_phy_idx); |
| } |
| |
| void bnx2x_calc_fc_adv(struct bnx2x *bp) |
| { |
| u8 cfg_idx = bnx2x_get_link_cfg_idx(bp); |
| switch (bp->link_vars.ieee_fc & |
| MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_MASK) { |
| case MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_NONE: |
| bp->port.advertising[cfg_idx] &= ~(ADVERTISED_Asym_Pause | |
| ADVERTISED_Pause); |
| break; |
| |
| case MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH: |
| bp->port.advertising[cfg_idx] |= (ADVERTISED_Asym_Pause | |
| ADVERTISED_Pause); |
| break; |
| |
| case MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC: |
| bp->port.advertising[cfg_idx] |= ADVERTISED_Asym_Pause; |
| break; |
| |
| default: |
| bp->port.advertising[cfg_idx] &= ~(ADVERTISED_Asym_Pause | |
| ADVERTISED_Pause); |
| break; |
| } |
| } |
| |
| |
| u8 bnx2x_initial_phy_init(struct bnx2x *bp, int load_mode) |
| { |
| if (!BP_NOMCP(bp)) { |
| u8 rc; |
| int cfx_idx = bnx2x_get_link_cfg_idx(bp); |
| u16 req_line_speed = bp->link_params.req_line_speed[cfx_idx]; |
| /* Initialize link parameters structure variables */ |
| /* It is recommended to turn off RX FC for jumbo frames |
| for better performance */ |
| if (bp->dev->mtu > 5000) |
| bp->link_params.req_fc_auto_adv = BNX2X_FLOW_CTRL_TX; |
| else |
| bp->link_params.req_fc_auto_adv = BNX2X_FLOW_CTRL_BOTH; |
| |
| bnx2x_acquire_phy_lock(bp); |
| |
| if (load_mode == LOAD_DIAG) { |
| bp->link_params.loopback_mode = LOOPBACK_XGXS; |
| bp->link_params.req_line_speed[cfx_idx] = SPEED_10000; |
| } |
| |
| rc = bnx2x_phy_init(&bp->link_params, &bp->link_vars); |
| |
| bnx2x_release_phy_lock(bp); |
| |
| bnx2x_calc_fc_adv(bp); |
| |
| if (CHIP_REV_IS_SLOW(bp) && bp->link_vars.link_up) { |
| bnx2x_stats_handle(bp, STATS_EVENT_LINK_UP); |
| bnx2x_link_report(bp); |
| } |
| bp->link_params.req_line_speed[cfx_idx] = req_line_speed; |
| return rc; |
| } |
| BNX2X_ERR("Bootcode is missing - can not initialize link\n"); |
| return -EINVAL; |
| } |
| |
| void bnx2x_link_set(struct bnx2x *bp) |
| { |
| if (!BP_NOMCP(bp)) { |
| bnx2x_acquire_phy_lock(bp); |
| bnx2x_link_reset(&bp->link_params, &bp->link_vars, 1); |
| bnx2x_phy_init(&bp->link_params, &bp->link_vars); |
| bnx2x_release_phy_lock(bp); |
| |
| bnx2x_calc_fc_adv(bp); |
| } else |
| BNX2X_ERR("Bootcode is missing - can not set link\n"); |
| } |
| |
| static void bnx2x__link_reset(struct bnx2x *bp) |
| { |
| if (!BP_NOMCP(bp)) { |
| bnx2x_acquire_phy_lock(bp); |
| bnx2x_link_reset(&bp->link_params, &bp->link_vars, 1); |
| bnx2x_release_phy_lock(bp); |
| } else |
| BNX2X_ERR("Bootcode is missing - can not reset link\n"); |
| } |
| |
| u8 bnx2x_link_test(struct bnx2x *bp, u8 is_serdes) |
| { |
| u8 rc = 0; |
| |
| if (!BP_NOMCP(bp)) { |
| bnx2x_acquire_phy_lock(bp); |
| rc = bnx2x_test_link(&bp->link_params, &bp->link_vars, |
| is_serdes); |
| bnx2x_release_phy_lock(bp); |
| } else |
| BNX2X_ERR("Bootcode is missing - can not test link\n"); |
| |
| return rc; |
| } |
| |
| static void bnx2x_init_port_minmax(struct bnx2x *bp) |
| { |
| u32 r_param = bp->link_vars.line_speed / 8; |
| u32 fair_periodic_timeout_usec; |
| u32 t_fair; |
| |
| memset(&(bp->cmng.rs_vars), 0, |
| sizeof(struct rate_shaping_vars_per_port)); |
| memset(&(bp->cmng.fair_vars), 0, sizeof(struct fairness_vars_per_port)); |
| |
| /* 100 usec in SDM ticks = 25 since each tick is 4 usec */ |
| bp->cmng.rs_vars.rs_periodic_timeout = RS_PERIODIC_TIMEOUT_USEC / 4; |
| |
| /* this is the threshold below which no timer arming will occur |
| 1.25 coefficient is for the threshold to be a little bigger |
| than the real time, to compensate for timer in-accuracy */ |
| bp->cmng.rs_vars.rs_threshold = |
| (RS_PERIODIC_TIMEOUT_USEC * r_param * 5) / 4; |
| |
| /* resolution of fairness timer */ |
| fair_periodic_timeout_usec = QM_ARB_BYTES / r_param; |
| /* for 10G it is 1000usec. for 1G it is 10000usec. */ |
| t_fair = T_FAIR_COEF / bp->link_vars.line_speed; |
| |
| /* this is the threshold below which we won't arm the timer anymore */ |
| bp->cmng.fair_vars.fair_threshold = QM_ARB_BYTES; |
| |
| /* we multiply by 1e3/8 to get bytes/msec. |
| We don't want the credits to pass a credit |
| of the t_fair*FAIR_MEM (algorithm resolution) */ |
| bp->cmng.fair_vars.upper_bound = r_param * t_fair * FAIR_MEM; |
| /* since each tick is 4 usec */ |
| bp->cmng.fair_vars.fairness_timeout = fair_periodic_timeout_usec / 4; |
| } |
| |
| /* Calculates the sum of vn_min_rates. |
| It's needed for further normalizing of the min_rates. |
| Returns: |
| sum of vn_min_rates. |
| or |
| 0 - if all the min_rates are 0. |
| In the later case fainess algorithm should be deactivated. |
| If not all min_rates are zero then those that are zeroes will be set to 1. |
| */ |
| static void bnx2x_calc_vn_weight_sum(struct bnx2x *bp) |
| { |
| int all_zero = 1; |
| int port = BP_PORT(bp); |
| int vn; |
| |
| bp->vn_weight_sum = 0; |
| for (vn = VN_0; vn < E1HVN_MAX; vn++) { |
| int func = 2*vn + port; |
| u32 vn_cfg = SHMEM_RD(bp, mf_cfg.func_mf_config[func].config); |
| u32 vn_min_rate = ((vn_cfg & FUNC_MF_CFG_MIN_BW_MASK) >> |
| FUNC_MF_CFG_MIN_BW_SHIFT) * 100; |
| |
| /* Skip hidden vns */ |
| if (vn_cfg & FUNC_MF_CFG_FUNC_HIDE) |
| continue; |
| |
| /* If min rate is zero - set it to 1 */ |
| if (!vn_min_rate) |
| vn_min_rate = DEF_MIN_RATE; |
| else |
| all_zero = 0; |
| |
| bp->vn_weight_sum += vn_min_rate; |
| } |
| |
| /* ... only if all min rates are zeros - disable fairness */ |
| if (all_zero) { |
| bp->cmng.flags.cmng_enables &= |
| ~CMNG_FLAGS_PER_PORT_FAIRNESS_VN; |
| DP(NETIF_MSG_IFUP, "All MIN values are zeroes" |
| " fairness will be disabled\n"); |
| } else |
| bp->cmng.flags.cmng_enables |= |
| CMNG_FLAGS_PER_PORT_FAIRNESS_VN; |
| } |
| |
| static void bnx2x_init_vn_minmax(struct bnx2x *bp, int func) |
| { |
| struct rate_shaping_vars_per_vn m_rs_vn; |
| struct fairness_vars_per_vn m_fair_vn; |
| u32 vn_cfg = SHMEM_RD(bp, mf_cfg.func_mf_config[func].config); |
| u16 vn_min_rate, vn_max_rate; |
| int i; |
| |
| /* If function is hidden - set min and max to zeroes */ |
| if (vn_cfg & FUNC_MF_CFG_FUNC_HIDE) { |
| vn_min_rate = 0; |
| vn_max_rate = 0; |
| |
| } else { |
| vn_min_rate = ((vn_cfg & FUNC_MF_CFG_MIN_BW_MASK) >> |
| FUNC_MF_CFG_MIN_BW_SHIFT) * 100; |
| /* If min rate is zero - set it to 1 */ |
| if (!vn_min_rate) |
| vn_min_rate = DEF_MIN_RATE; |
| vn_max_rate = ((vn_cfg & FUNC_MF_CFG_MAX_BW_MASK) >> |
| FUNC_MF_CFG_MAX_BW_SHIFT) * 100; |
| } |
| DP(NETIF_MSG_IFUP, |
| "func %d: vn_min_rate %d vn_max_rate %d vn_weight_sum %d\n", |
| func, vn_min_rate, vn_max_rate, bp->vn_weight_sum); |
| |
| memset(&m_rs_vn, 0, sizeof(struct rate_shaping_vars_per_vn)); |
| memset(&m_fair_vn, 0, sizeof(struct fairness_vars_per_vn)); |
| |
| /* global vn counter - maximal Mbps for this vn */ |
| m_rs_vn.vn_counter.rate = vn_max_rate; |
| |
| /* quota - number of bytes transmitted in this period */ |
| m_rs_vn.vn_counter.quota = |
| (vn_max_rate * RS_PERIODIC_TIMEOUT_USEC) / 8; |
| |
| if (bp->vn_weight_sum) { |
| /* credit for each period of the fairness algorithm: |
| number of bytes in T_FAIR (the vn share the port rate). |
| vn_weight_sum should not be larger than 10000, thus |
| T_FAIR_COEF / (8 * vn_weight_sum) will always be greater |
| than zero */ |
| m_fair_vn.vn_credit_delta = |
| max_t(u32, (vn_min_rate * (T_FAIR_COEF / |
| (8 * bp->vn_weight_sum))), |
| (bp->cmng.fair_vars.fair_threshold * 2)); |
| DP(NETIF_MSG_IFUP, "m_fair_vn.vn_credit_delta %d\n", |
| m_fair_vn.vn_credit_delta); |
| } |
| |
| /* Store it to internal memory */ |
| for (i = 0; i < sizeof(struct rate_shaping_vars_per_vn)/4; i++) |
| REG_WR(bp, BAR_XSTRORM_INTMEM + |
| XSTORM_RATE_SHAPING_PER_VN_VARS_OFFSET(func) + i * 4, |
| ((u32 *)(&m_rs_vn))[i]); |
| |
| for (i = 0; i < sizeof(struct fairness_vars_per_vn)/4; i++) |
| REG_WR(bp, BAR_XSTRORM_INTMEM + |
| XSTORM_FAIRNESS_PER_VN_VARS_OFFSET(func) + i * 4, |
| ((u32 *)(&m_fair_vn))[i]); |
| } |
| |
| |
| /* This function is called upon link interrupt */ |
| static void bnx2x_link_attn(struct bnx2x *bp) |
| { |
| u32 prev_link_status = bp->link_vars.link_status; |
| /* Make sure that we are synced with the current statistics */ |
| bnx2x_stats_handle(bp, STATS_EVENT_STOP); |
| |
| bnx2x_link_update(&bp->link_params, &bp->link_vars); |
| |
| if (bp->link_vars.link_up) { |
| |
| /* dropless flow control */ |
| if (CHIP_IS_E1H(bp) && bp->dropless_fc) { |
| int port = BP_PORT(bp); |
| u32 pause_enabled = 0; |
| |
| if (bp->link_vars.flow_ctrl & BNX2X_FLOW_CTRL_TX) |
| pause_enabled = 1; |
| |
| REG_WR(bp, BAR_USTRORM_INTMEM + |
| USTORM_ETH_PAUSE_ENABLED_OFFSET(port), |
| pause_enabled); |
| } |
| |
| if (bp->link_vars.mac_type == MAC_TYPE_BMAC) { |
| struct host_port_stats *pstats; |
| |
| pstats = bnx2x_sp(bp, port_stats); |
| /* reset old bmac stats */ |
| memset(&(pstats->mac_stx[0]), 0, |
| sizeof(struct mac_stx)); |
| } |
| if (bp->state == BNX2X_STATE_OPEN) |
| bnx2x_stats_handle(bp, STATS_EVENT_LINK_UP); |
| } |
| |
| /* indicate link status only if link status actually changed */ |
| if (prev_link_status != bp->link_vars.link_status) |
| bnx2x_link_report(bp); |
| |
| if (IS_E1HMF(bp)) { |
| int port = BP_PORT(bp); |
| int func; |
| int vn; |
| |
| /* Set the attention towards other drivers on the same port */ |
| for (vn = VN_0; vn < E1HVN_MAX; vn++) { |
| if (vn == BP_E1HVN(bp)) |
| continue; |
| |
| func = ((vn << 1) | port); |
| REG_WR(bp, MISC_REG_AEU_GENERAL_ATTN_0 + |
| (LINK_SYNC_ATTENTION_BIT_FUNC_0 + func)*4, 1); |
| } |
| |
| if (bp->link_vars.link_up) { |
| int i; |
| |
| /* Init rate shaping and fairness contexts */ |
| bnx2x_init_port_minmax(bp); |
| |
| for (vn = VN_0; vn < E1HVN_MAX; vn++) |
| bnx2x_init_vn_minmax(bp, 2*vn + port); |
| |
| /* Store it to internal memory */ |
| for (i = 0; |
| i < sizeof(struct cmng_struct_per_port) / 4; i++) |
| REG_WR(bp, BAR_XSTRORM_INTMEM + |
| XSTORM_CMNG_PER_PORT_VARS_OFFSET(port) + i*4, |
| ((u32 *)(&bp->cmng))[i]); |
| } |
| } |
| } |
| |
| void bnx2x__link_status_update(struct bnx2x *bp) |
| { |
| if ((bp->state != BNX2X_STATE_OPEN) || (bp->flags & MF_FUNC_DIS)) |
| return; |
| |
| bnx2x_link_status_update(&bp->link_params, &bp->link_vars); |
| |
| if (bp->link_vars.link_up) |
| bnx2x_stats_handle(bp, STATS_EVENT_LINK_UP); |
| else |
| bnx2x_stats_handle(bp, STATS_EVENT_STOP); |
| |
| bnx2x_calc_vn_weight_sum(bp); |
| |
| /* indicate link status */ |
| bnx2x_link_report(bp); |
| } |
| |
| static void bnx2x_pmf_update(struct bnx2x *bp) |
| { |
| int port = BP_PORT(bp); |
| u32 val; |
| |
| bp->port.pmf = 1; |
| DP(NETIF_MSG_LINK, "pmf %d\n", bp->port.pmf); |
| |
| /* enable nig attention */ |
| val = (0xff0f | (1 << (BP_E1HVN(bp) + 4))); |
| REG_WR(bp, HC_REG_TRAILING_EDGE_0 + port*8, val); |
| REG_WR(bp, HC_REG_LEADING_EDGE_0 + port*8, val); |
| |
| bnx2x_stats_handle(bp, STATS_EVENT_PMF); |
| } |
| |
| /* end of Link */ |
| |
| /* slow path */ |
| |
| /* |
| * General service functions |
| */ |
| |
| /* send the MCP a request, block until there is a reply */ |
| u32 bnx2x_fw_command(struct bnx2x *bp, u32 command, u32 param) |
| { |
| int func = BP_FUNC(bp); |
| u32 seq = ++bp->fw_seq; |
| u32 rc = 0; |
| u32 cnt = 1; |
| u8 delay = CHIP_REV_IS_SLOW(bp) ? 100 : 10; |
| |
| mutex_lock(&bp->fw_mb_mutex); |
| SHMEM_WR(bp, func_mb[func].drv_mb_param, param); |
| SHMEM_WR(bp, func_mb[func].drv_mb_header, (command | seq)); |
| DP(BNX2X_MSG_MCP, "wrote command (%x) to FW MB\n", (command | seq)); |
| |
| do { |
| /* let the FW do it's magic ... */ |
| msleep(delay); |
| |
| rc = SHMEM_RD(bp, func_mb[func].fw_mb_header); |
| |
| /* Give the FW up to 5 second (500*10ms) */ |
| } while ((seq != (rc & FW_MSG_SEQ_NUMBER_MASK)) && (cnt++ < 500)); |
| |
| DP(BNX2X_MSG_MCP, "[after %d ms] read (%x) seq is (%x) from FW MB\n", |
| cnt*delay, rc, seq); |
| |
| /* is this a reply to our command? */ |
| if (seq == (rc & FW_MSG_SEQ_NUMBER_MASK)) |
| rc &= FW_MSG_CODE_MASK; |
| else { |
| /* FW BUG! */ |
| BNX2X_ERR("FW failed to respond!\n"); |
| bnx2x_fw_dump(bp); |
| rc = 0; |
| } |
| mutex_unlock(&bp->fw_mb_mutex); |
| |
| return rc; |
| } |
| |
| static void bnx2x_e1h_disable(struct bnx2x *bp) |
| { |
| int port = BP_PORT(bp); |
| |
| netif_tx_disable(bp->dev); |
| |
| REG_WR(bp, NIG_REG_LLH0_FUNC_EN + port*8, 0); |
| |
| netif_carrier_off(bp->dev); |
| } |
| |
| static void bnx2x_e1h_enable(struct bnx2x *bp) |
| { |
| int port = BP_PORT(bp); |
| |
| REG_WR(bp, NIG_REG_LLH0_FUNC_EN + port*8, 1); |
| |
| /* Tx queue should be only reenabled */ |
| netif_tx_wake_all_queues(bp->dev); |
| |
| /* |
| * Should not call netif_carrier_on since it will be called if the link |
| * is up when checking for link state |
| */ |
| } |
| |
| static void bnx2x_update_min_max(struct bnx2x *bp) |
| { |
| int port = BP_PORT(bp); |
| int vn, i; |
| |
| /* Init rate shaping and fairness contexts */ |
| bnx2x_init_port_minmax(bp); |
| |
| bnx2x_calc_vn_weight_sum(bp); |
| |
| for (vn = VN_0; vn < E1HVN_MAX; vn++) |
| bnx2x_init_vn_minmax(bp, 2*vn + port); |
| |
| if (bp->port.pmf) { |
| int func; |
| |
| /* Set the attention towards other drivers on the same port */ |
| for (vn = VN_0; vn < E1HVN_MAX; vn++) { |
| if (vn == BP_E1HVN(bp)) |
| continue; |
| |
| func = ((vn << 1) | port); |
| REG_WR(bp, MISC_REG_AEU_GENERAL_ATTN_0 + |
| (LINK_SYNC_ATTENTION_BIT_FUNC_0 + func)*4, 1); |
| } |
| |
| /* Store it to internal memory */ |
| for (i = 0; i < sizeof(struct cmng_struct_per_port) / 4; i++) |
| REG_WR(bp, BAR_XSTRORM_INTMEM + |
| XSTORM_CMNG_PER_PORT_VARS_OFFSET(port) + i*4, |
| ((u32 *)(&bp->cmng))[i]); |
| } |
| } |
| |
| static void bnx2x_dcc_event(struct bnx2x *bp, u32 dcc_event) |
| { |
| DP(BNX2X_MSG_MCP, "dcc_event 0x%x\n", dcc_event); |
| |
| if (dcc_event & DRV_STATUS_DCC_DISABLE_ENABLE_PF) { |
| |
| /* |
| * This is the only place besides the function initialization |
| * where the bp->flags can change so it is done without any |
| * locks |
| */ |
| if (bp->mf_config & FUNC_MF_CFG_FUNC_DISABLED) { |
| DP(NETIF_MSG_IFDOWN, "mf_cfg function disabled\n"); |
| bp->flags |= MF_FUNC_DIS; |
| |
| bnx2x_e1h_disable(bp); |
| } else { |
| DP(NETIF_MSG_IFUP, "mf_cfg function enabled\n"); |
| bp->flags &= ~MF_FUNC_DIS; |
| |
| bnx2x_e1h_enable(bp); |
| } |
| dcc_event &= ~DRV_STATUS_DCC_DISABLE_ENABLE_PF; |
| } |
| if (dcc_event & DRV_STATUS_DCC_BANDWIDTH_ALLOCATION) { |
| |
| bnx2x_update_min_max(bp); |
| dcc_event &= ~DRV_STATUS_DCC_BANDWIDTH_ALLOCATION; |
| } |
| |
| /* Report results to MCP */ |
| if (dcc_event) |
| bnx2x_fw_command(bp, DRV_MSG_CODE_DCC_FAILURE, 0); |
| else |
| bnx2x_fw_command(bp, DRV_MSG_CODE_DCC_OK, 0); |
| } |
| |
| /* must be called under the spq lock */ |
| static inline struct eth_spe *bnx2x_sp_get_next(struct bnx2x *bp) |
| { |
| struct eth_spe *next_spe = bp->spq_prod_bd; |
| |
| if (bp->spq_prod_bd == bp->spq_last_bd) { |
| bp->spq_prod_bd = bp->spq; |
| bp->spq_prod_idx = 0; |
| DP(NETIF_MSG_TIMER, "end of spq\n"); |
| } else { |
| bp->spq_prod_bd++; |
| bp->spq_prod_idx++; |
| } |
| return next_spe; |
| } |
| |
| /* must be called under the spq lock */ |
| static inline void bnx2x_sp_prod_update(struct bnx2x *bp) |
| { |
| int func = BP_FUNC(bp); |
| |
| /* Make sure that BD data is updated before writing the producer */ |
| wmb(); |
| |
| REG_WR(bp, BAR_XSTRORM_INTMEM + XSTORM_SPQ_PROD_OFFSET(func), |
| bp->spq_prod_idx); |
| mmiowb(); |
| } |
| |
| /* the slow path queue is odd since completions arrive on the fastpath ring */ |
| int bnx2x_sp_post(struct bnx2x *bp, int command, int cid, |
| u32 data_hi, u32 data_lo, int common) |
| { |
| struct eth_spe *spe; |
| |
| #ifdef BNX2X_STOP_ON_ERROR |
| if (unlikely(bp->panic)) |
| return -EIO; |
| #endif |
| |
| spin_lock_bh(&bp->spq_lock); |
| |
| if (!bp->spq_left) { |
| BNX2X_ERR("BUG! SPQ ring full!\n"); |
| spin_unlock_bh(&bp->spq_lock); |
| bnx2x_panic(); |
| return -EBUSY; |
| } |
| |
| spe = bnx2x_sp_get_next(bp); |
| |
| /* CID needs port number to be encoded int it */ |
| spe->hdr.conn_and_cmd_data = |
| cpu_to_le32((command << SPE_HDR_CMD_ID_SHIFT) | |
| HW_CID(bp, cid)); |
| spe->hdr.type = cpu_to_le16(ETH_CONNECTION_TYPE); |
| if (common) |
| spe->hdr.type |= |
| cpu_to_le16((1 << SPE_HDR_COMMON_RAMROD_SHIFT)); |
| |
| spe->data.mac_config_addr.hi = cpu_to_le32(data_hi); |
| spe->data.mac_config_addr.lo = cpu_to_le32(data_lo); |
| |
| bp->spq_left--; |
| |
| DP(BNX2X_MSG_SP/*NETIF_MSG_TIMER*/, |
| "SPQE[%x] (%x:%x) command %d hw_cid %x data (%x:%x) left %x\n", |
| bp->spq_prod_idx, (u32)U64_HI(bp->spq_mapping), |
| (u32)(U64_LO(bp->spq_mapping) + |
| (void *)bp->spq_prod_bd - (void *)bp->spq), command, |
| HW_CID(bp, cid), data_hi, data_lo, bp->spq_left); |
| |
| bnx2x_sp_prod_update(bp); |
| spin_unlock_bh(&bp->spq_lock); |
| return 0; |
| } |
| |
| /* acquire split MCP access lock register */ |
| static int bnx2x_acquire_alr(struct bnx2x *bp) |
| { |
| u32 j, val; |
| int rc = 0; |
| |
| might_sleep(); |
| for (j = 0; j < 1000; j++) { |
| val = (1UL << 31); |
| REG_WR(bp, GRCBASE_MCP + 0x9c, val); |
| val = REG_RD(bp, GRCBASE_MCP + 0x9c); |
| if (val & (1L << 31)) |
| break; |
| |
| msleep(5); |
| } |
| if (!(val & (1L << 31))) { |
| BNX2X_ERR("Cannot acquire MCP access lock register\n"); |
| rc = -EBUSY; |
| } |
| |
| return rc; |
| } |
| |
| /* release split MCP access lock register */ |
| static void bnx2x_release_alr(struct bnx2x *bp) |
| { |
| REG_WR(bp, GRCBASE_MCP + 0x9c, 0); |
| } |
| |
| static inline u16 bnx2x_update_dsb_idx(struct bnx2x *bp) |
| { |
| struct host_def_status_block *def_sb = bp->def_status_blk; |
| u16 rc = 0; |
| |
| barrier(); /* status block is written to by the chip */ |
| if (bp->def_att_idx != def_sb->atten_status_block.attn_bits_index) { |
| bp->def_att_idx = def_sb->atten_status_block.attn_bits_index; |
| rc |= 1; |
| } |
| if (bp->def_c_idx != def_sb->c_def_status_block.status_block_index) { |
| bp->def_c_idx = def_sb->c_def_status_block.status_block_index; |
| rc |= 2; |
| } |
| if (bp->def_u_idx != def_sb->u_def_status_block.status_block_index) { |
| bp->def_u_idx = def_sb->u_def_status_block.status_block_index; |
| rc |= 4; |
| } |
| if (bp->def_x_idx != def_sb->x_def_status_block.status_block_index) { |
| bp->def_x_idx = def_sb->x_def_status_block.status_block_index; |
| rc |= 8; |
| } |
| if (bp->def_t_idx != def_sb->t_def_status_block.status_block_index) { |
| bp->def_t_idx = def_sb->t_def_status_block.status_block_index; |
| rc |= 16; |
| } |
| return rc; |
| } |
| |
| /* |
| * slow path service functions |
| */ |
| |
| static void bnx2x_attn_int_asserted(struct bnx2x *bp, u32 asserted) |
| { |
| int port = BP_PORT(bp); |
| u32 hc_addr = (HC_REG_COMMAND_REG + port*32 + |
| COMMAND_REG_ATTN_BITS_SET); |
| u32 aeu_addr = port ? MISC_REG_AEU_MASK_ATTN_FUNC_1 : |
| MISC_REG_AEU_MASK_ATTN_FUNC_0; |
| u32 nig_int_mask_addr = port ? NIG_REG_MASK_INTERRUPT_PORT1 : |
| NIG_REG_MASK_INTERRUPT_PORT0; |
| u32 aeu_mask; |
| u32 nig_mask = 0; |
| |
| if (bp->attn_state & asserted) |
| BNX2X_ERR("IGU ERROR\n"); |
| |
| bnx2x_acquire_hw_lock(bp, HW_LOCK_RESOURCE_PORT0_ATT_MASK + port); |
| aeu_mask = REG_RD(bp, aeu_addr); |
| |
| DP(NETIF_MSG_HW, "aeu_mask %x newly asserted %x\n", |
| aeu_mask, asserted); |
| aeu_mask &= ~(asserted & 0x3ff); |
| DP(NETIF_MSG_HW, "new mask %x\n", aeu_mask); |
| |
| REG_WR(bp, aeu_addr, aeu_mask); |
| bnx2x_release_hw_lock(bp, HW_LOCK_RESOURCE_PORT0_ATT_MASK + port); |
| |
| DP(NETIF_MSG_HW, "attn_state %x\n", bp->attn_state); |
| bp->attn_state |= asserted; |
| DP(NETIF_MSG_HW, "new state %x\n", bp->attn_state); |
| |
| if (asserted & ATTN_HARD_WIRED_MASK) { |
| if (asserted & ATTN_NIG_FOR_FUNC) { |
| |
| bnx2x_acquire_phy_lock(bp); |
| |
| /* save nig interrupt mask */ |
| nig_mask = REG_RD(bp, nig_int_mask_addr); |
| REG_WR(bp, nig_int_mask_addr, 0); |
| |
| bnx2x_link_attn(bp); |
| |
| /* handle unicore attn? */ |
| } |
| if (asserted & ATTN_SW_TIMER_4_FUNC) |
| DP(NETIF_MSG_HW, "ATTN_SW_TIMER_4_FUNC!\n"); |
| |
| if (asserted & GPIO_2_FUNC) |
| DP(NETIF_MSG_HW, "GPIO_2_FUNC!\n"); |
| |
| if (asserted & GPIO_3_FUNC) |
| DP(NETIF_MSG_HW, "GPIO_3_FUNC!\n"); |
| |
| if (asserted & GPIO_4_FUNC) |
| DP(NETIF_MSG_HW, "GPIO_4_FUNC!\n"); |
| |
| if (port == 0) { |
| if (asserted & ATTN_GENERAL_ATTN_1) { |
| DP(NETIF_MSG_HW, "ATTN_GENERAL_ATTN_1!\n"); |
| REG_WR(bp, MISC_REG_AEU_GENERAL_ATTN_1, 0x0); |
| } |
| if (asserted & ATTN_GENERAL_ATTN_2) { |
| DP(NETIF_MSG_HW, "ATTN_GENERAL_ATTN_2!\n"); |
| REG_WR(bp, MISC_REG_AEU_GENERAL_ATTN_2, 0x0); |
| } |
| if (asserted & ATTN_GENERAL_ATTN_3) { |
| DP(NETIF_MSG_HW, "ATTN_GENERAL_ATTN_3!\n"); |
| REG_WR(bp, MISC_REG_AEU_GENERAL_ATTN_3, 0x0); |
| } |
| } else { |
| if (asserted & ATTN_GENERAL_ATTN_4) { |
| DP(NETIF_MSG_HW, "ATTN_GENERAL_ATTN_4!\n"); |
| REG_WR(bp, MISC_REG_AEU_GENERAL_ATTN_4, 0x0); |
| } |
| if (asserted & ATTN_GENERAL_ATTN_5) { |
| DP(NETIF_MSG_HW, "ATTN_GENERAL_ATTN_5!\n"); |
| REG_WR(bp, MISC_REG_AEU_GENERAL_ATTN_5, 0x0); |
| } |
| if (asserted & ATTN_GENERAL_ATTN_6) { |
| DP(NETIF_MSG_HW, "ATTN_GENERAL_ATTN_6!\n"); |
| REG_WR(bp, MISC_REG_AEU_GENERAL_ATTN_6, 0x0); |
| } |
| } |
| |
| } /* if hardwired */ |
| |
| DP(NETIF_MSG_HW, "about to mask 0x%08x at HC addr 0x%x\n", |
| asserted, hc_addr); |
| REG_WR(bp, hc_addr, asserted); |
| |
| /* now set back the mask */ |
| if (asserted & ATTN_NIG_FOR_FUNC) { |
| REG_WR(bp, nig_int_mask_addr, nig_mask); |
| bnx2x_release_phy_lock(bp); |
| } |
| } |
| |
| static inline void bnx2x_fan_failure(struct bnx2x *bp) |
| { |
| int port = BP_PORT(bp); |
| u32 ext_phy_config; |
| /* mark the failure */ |
| ext_phy_config = |
| SHMEM_RD(bp, |
| dev_info.port_hw_config[port].external_phy_config); |
| |
| ext_phy_config &= ~PORT_HW_CFG_XGXS_EXT_PHY_TYPE_MASK; |
| ext_phy_config |= PORT_HW_CFG_XGXS_EXT_PHY_TYPE_FAILURE; |
| SHMEM_WR(bp, dev_info.port_hw_config[port].external_phy_config, |
| ext_phy_config); |
| |
| /* log the failure */ |
| netdev_err(bp->dev, "Fan Failure on Network Controller has caused" |
| " the driver to shutdown the card to prevent permanent" |
| " damage. Please contact OEM Support for assistance\n"); |
| } |
| |
| static inline void bnx2x_attn_int_deasserted0(struct bnx2x *bp, u32 attn) |
| { |
| int port = BP_PORT(bp); |
| int reg_offset; |
| u32 val; |
| |
| reg_offset = (port ? MISC_REG_AEU_ENABLE1_FUNC_1_OUT_0 : |
| MISC_REG_AEU_ENABLE1_FUNC_0_OUT_0); |
| |
| if (attn & AEU_INPUTS_ATTN_BITS_SPIO5) { |
| |
| val = REG_RD(bp, reg_offset); |
| val &= ~AEU_INPUTS_ATTN_BITS_SPIO5; |
| REG_WR(bp, reg_offset, val); |
| |
| BNX2X_ERR("SPIO5 hw attention\n"); |
| |
| /* Fan failure attention */ |
| bnx2x_hw_reset_phy(&bp->link_params); |
| bnx2x_fan_failure(bp); |
| } |
| |
| if (attn & (AEU_INPUTS_ATTN_BITS_GPIO3_FUNCTION_0 | |
| AEU_INPUTS_ATTN_BITS_GPIO3_FUNCTION_1)) { |
| bnx2x_acquire_phy_lock(bp); |
| bnx2x_handle_module_detect_int(&bp->link_params); |
| bnx2x_release_phy_lock(bp); |
| } |
| |
| if (attn & HW_INTERRUT_ASSERT_SET_0) { |
| |
| val = REG_RD(bp, reg_offset); |
| val &= ~(attn & HW_INTERRUT_ASSERT_SET_0); |
| REG_WR(bp, reg_offset, val); |
| |
| BNX2X_ERR("FATAL HW block attention set0 0x%x\n", |
| (u32)(attn & HW_INTERRUT_ASSERT_SET_0)); |
| bnx2x_panic(); |
| } |
| } |
| |
| static inline void bnx2x_attn_int_deasserted1(struct bnx2x *bp, u32 attn) |
| { |
| u32 val; |
| |
| if (attn & AEU_INPUTS_ATTN_BITS_DOORBELLQ_HW_INTERRUPT) { |
| |
| val = REG_RD(bp, DORQ_REG_DORQ_INT_STS_CLR); |
| BNX2X_ERR("DB hw attention 0x%x\n", val); |
| /* DORQ discard attention */ |
| if (val & 0x2) |
| BNX2X_ERR("FATAL error from DORQ\n"); |
| } |
| |
| if (attn & HW_INTERRUT_ASSERT_SET_1) { |
| |
| int port = BP_PORT(bp); |
| int reg_offset; |
| |
| reg_offset = (port ? MISC_REG_AEU_ENABLE1_FUNC_1_OUT_1 : |
| MISC_REG_AEU_ENABLE1_FUNC_0_OUT_1); |
| |
| val = REG_RD(bp, reg_offset); |
| val &= ~(attn & HW_INTERRUT_ASSERT_SET_1); |
| REG_WR(bp, reg_offset, val); |
| |
| BNX2X_ERR("FATAL HW block attention set1 0x%x\n", |
| (u32)(attn & HW_INTERRUT_ASSERT_SET_1)); |
| bnx2x_panic(); |
| } |
| } |
| |
| static inline void bnx2x_attn_int_deasserted2(struct bnx2x *bp, u32 attn) |
| { |
| u32 val; |
| |
| if (attn & AEU_INPUTS_ATTN_BITS_CFC_HW_INTERRUPT) { |
| |
| val = REG_RD(bp, CFC_REG_CFC_INT_STS_CLR); |
| BNX2X_ERR("CFC hw attention 0x%x\n", val); |
| /* CFC error attention */ |
| if (val & 0x2) |
| BNX2X_ERR("FATAL error from CFC\n"); |
| } |
| |
| if (attn & AEU_INPUTS_ATTN_BITS_PXP_HW_INTERRUPT) { |
| |
| val = REG_RD(bp, PXP_REG_PXP_INT_STS_CLR_0); |
| BNX2X_ERR("PXP hw attention 0x%x\n", val); |
| /* RQ_USDMDP_FIFO_OVERFLOW */ |
| if (val & 0x18000) |
| BNX2X_ERR("FATAL error from PXP\n"); |
| } |
| |
| if (attn & HW_INTERRUT_ASSERT_SET_2) { |
| |
| int port = BP_PORT(bp); |
| int reg_offset; |
| |
| reg_offset = (port ? MISC_REG_AEU_ENABLE1_FUNC_1_OUT_2 : |
| MISC_REG_AEU_ENABLE1_FUNC_0_OUT_2); |
| |
| val = REG_RD(bp, reg_offset); |
| val &= ~(attn & HW_INTERRUT_ASSERT_SET_2); |
| REG_WR(bp, reg_offset, val); |
| |
| BNX2X_ERR("FATAL HW block attention set2 0x%x\n", |
| (u32)(attn & HW_INTERRUT_ASSERT_SET_2)); |
| bnx2x_panic(); |
| } |
| } |
| |
| static inline void bnx2x_attn_int_deasserted3(struct bnx2x *bp, u32 attn) |
| { |
| u32 val; |
| |
| if (attn & EVEREST_GEN_ATTN_IN_USE_MASK) { |
| |
| if (attn & BNX2X_PMF_LINK_ASSERT) { |
| int func = BP_FUNC(bp); |
| |
| REG_WR(bp, MISC_REG_AEU_GENERAL_ATTN_12 + func*4, 0); |
| bp->mf_config = SHMEM_RD(bp, |
| mf_cfg.func_mf_config[func].config); |
| val = SHMEM_RD(bp, func_mb[func].drv_status); |
| if (val & DRV_STATUS_DCC_EVENT_MASK) |
| bnx2x_dcc_event(bp, |
| (val & DRV_STATUS_DCC_EVENT_MASK)); |
| bnx2x__link_status_update(bp); |
| if ((bp->port.pmf == 0) && (val & DRV_STATUS_PMF)) |
| bnx2x_pmf_update(bp); |
| |
| } else if (attn & BNX2X_MC_ASSERT_BITS) { |
| |
| BNX2X_ERR("MC assert!\n"); |
| REG_WR(bp, MISC_REG_AEU_GENERAL_ATTN_10, 0); |
| REG_WR(bp, MISC_REG_AEU_GENERAL_ATTN_9, 0); |
| REG_WR(bp, MISC_REG_AEU_GENERAL_ATTN_8, 0); |
| REG_WR(bp, MISC_REG_AEU_GENERAL_ATTN_7, 0); |
| bnx2x_panic(); |
| |
| } else if (attn & BNX2X_MCP_ASSERT) { |
| |
| BNX2X_ERR("MCP assert!\n"); |
| REG_WR(bp, MISC_REG_AEU_GENERAL_ATTN_11, 0); |
| bnx2x_fw_dump(bp); |
| |
| } else |
| BNX2X_ERR("Unknown HW assert! (attn 0x%x)\n", attn); |
| } |
| |
| if (attn & EVEREST_LATCHED_ATTN_IN_USE_MASK) { |
| BNX2X_ERR("LATCHED attention 0x%08x (masked)\n", attn); |
| if (attn & BNX2X_GRC_TIMEOUT) { |
| val = CHIP_IS_E1H(bp) ? |
| REG_RD(bp, MISC_REG_GRC_TIMEOUT_ATTN) : 0; |
| BNX2X_ERR("GRC time-out 0x%08x\n", val); |
| } |
| if (attn & BNX2X_GRC_RSV) { |
| val = CHIP_IS_E1H(bp) ? |
| REG_RD(bp, MISC_REG_GRC_RSV_ATTN) : 0; |
| BNX2X_ERR("GRC reserved 0x%08x\n", val); |
| } |
| REG_WR(bp, MISC_REG_AEU_CLR_LATCH_SIGNAL, 0x7ff); |
| } |
| } |
| |
| #define BNX2X_MISC_GEN_REG MISC_REG_GENERIC_POR_1 |
| #define LOAD_COUNTER_BITS 16 /* Number of bits for load counter */ |
| #define LOAD_COUNTER_MASK (((u32)0x1 << LOAD_COUNTER_BITS) - 1) |
| #define RESET_DONE_FLAG_MASK (~LOAD_COUNTER_MASK) |
| #define RESET_DONE_FLAG_SHIFT LOAD_COUNTER_BITS |
| #define CHIP_PARITY_SUPPORTED(bp) (CHIP_IS_E1(bp) || CHIP_IS_E1H(bp)) |
| /* |
| * should be run under rtnl lock |
| */ |
| static inline void bnx2x_set_reset_done(struct bnx2x *bp) |
| { |
| u32 val = REG_RD(bp, BNX2X_MISC_GEN_REG); |
| val &= ~(1 << RESET_DONE_FLAG_SHIFT); |
| REG_WR(bp, BNX2X_MISC_GEN_REG, val); |
| barrier(); |
| mmiowb(); |
| } |
| |
| /* |
| * should be run under rtnl lock |
| */ |
| static inline void bnx2x_set_reset_in_progress(struct bnx2x *bp) |
| { |
| u32 val = REG_RD(bp, BNX2X_MISC_GEN_REG); |
| val |= (1 << 16); |
| REG_WR(bp, BNX2X_MISC_GEN_REG, val); |
| barrier(); |
| mmiowb(); |
| } |
| |
| /* |
| * should be run under rtnl lock |
| */ |
| bool bnx2x_reset_is_done(struct bnx2x *bp) |
| { |
| u32 val = REG_RD(bp, BNX2X_MISC_GEN_REG); |
| DP(NETIF_MSG_HW, "GEN_REG_VAL=0x%08x\n", val); |
| return (val & RESET_DONE_FLAG_MASK) ? false : true; |
| } |
| |
| /* |
| * should be run under rtnl lock |
| */ |
| inline void bnx2x_inc_load_cnt(struct bnx2x *bp) |
| { |
| u32 val1, val = REG_RD(bp, BNX2X_MISC_GEN_REG); |
| |
| DP(NETIF_MSG_HW, "Old GEN_REG_VAL=0x%08x\n", val); |
| |
| val1 = ((val & LOAD_COUNTER_MASK) + 1) & LOAD_COUNTER_MASK; |
| REG_WR(bp, BNX2X_MISC_GEN_REG, (val & RESET_DONE_FLAG_MASK) | val1); |
| barrier(); |
| mmiowb(); |
| } |
| |
| /* |
| * should be run under rtnl lock |
| */ |
| u32 bnx2x_dec_load_cnt(struct bnx2x *bp) |
| { |
| u32 val1, val = REG_RD(bp, BNX2X_MISC_GEN_REG); |
| |
| DP(NETIF_MSG_HW, "Old GEN_REG_VAL=0x%08x\n", val); |
| |
| val1 = ((val & LOAD_COUNTER_MASK) - 1) & LOAD_COUNTER_MASK; |
| REG_WR(bp, BNX2X_MISC_GEN_REG, (val & RESET_DONE_FLAG_MASK) | val1); |
| barrier(); |
| mmiowb(); |
| |
| return val1; |
| } |
| |
| /* |
| * should be run under rtnl lock |
| */ |
| static inline u32 bnx2x_get_load_cnt(struct bnx2x *bp) |
| { |
| return REG_RD(bp, BNX2X_MISC_GEN_REG) & LOAD_COUNTER_MASK; |
| } |
| |
| static inline void bnx2x_clear_load_cnt(struct bnx2x *bp) |
| { |
| u32 val = REG_RD(bp, BNX2X_MISC_GEN_REG); |
| REG_WR(bp, BNX2X_MISC_GEN_REG, val & (~LOAD_COUNTER_MASK)); |
| } |
| |
| static inline void _print_next_block(int idx, const char *blk) |
| { |
| if (idx) |
| pr_cont(", "); |
| pr_cont("%s", blk); |
| } |
| |
| static inline int bnx2x_print_blocks_with_parity0(u32 sig, int par_num) |
| { |
| int i = 0; |
| u32 cur_bit = 0; |
| for (i = 0; sig; i++) { |
| cur_bit = ((u32)0x1 << i); |
| if (sig & cur_bit) { |
| switch (cur_bit) { |
| case AEU_INPUTS_ATTN_BITS_BRB_PARITY_ERROR: |
| _print_next_block(par_num++, "BRB"); |
| break; |
| case AEU_INPUTS_ATTN_BITS_PARSER_PARITY_ERROR: |
| _print_next_block(par_num++, "PARSER"); |
| break; |
| case AEU_INPUTS_ATTN_BITS_TSDM_PARITY_ERROR: |
| _print_next_block(par_num++, "TSDM"); |
| break; |
| case AEU_INPUTS_ATTN_BITS_SEARCHER_PARITY_ERROR: |
| _print_next_block(par_num++, "SEARCHER"); |
| break; |
| case AEU_INPUTS_ATTN_BITS_TSEMI_PARITY_ERROR: |
| _print_next_block(par_num++, "TSEMI"); |
| break; |
| } |
| |
| /* Clear the bit */ |
| sig &= ~cur_bit; |
| } |
| } |
| |
| return par_num; |
| } |
| |
| static inline int bnx2x_print_blocks_with_parity1(u32 sig, int par_num) |
| { |
| int i = 0; |
| u32 cur_bit = 0; |
| for (i = 0; sig; i++) { |
| cur_bit = ((u32)0x1 << i); |
| if (sig & cur_bit) { |
| switch (cur_bit) { |
| case AEU_INPUTS_ATTN_BITS_PBCLIENT_PARITY_ERROR: |
| _print_next_block(par_num++, "PBCLIENT"); |
| break; |
| case AEU_INPUTS_ATTN_BITS_QM_PARITY_ERROR: |
| _print_next_block(par_num++, "QM"); |
| break; |
| case AEU_INPUTS_ATTN_BITS_XSDM_PARITY_ERROR: |
| _print_next_block(par_num++, "XSDM"); |
| break; |
| case AEU_INPUTS_ATTN_BITS_XSEMI_PARITY_ERROR: |
| _print_next_block(par_num++, "XSEMI"); |
| break; |
| case AEU_INPUTS_ATTN_BITS_DOORBELLQ_PARITY_ERROR: |
| _print_next_block(par_num++, "DOORBELLQ"); |
| break; |
| case AEU_INPUTS_ATTN_BITS_VAUX_PCI_CORE_PARITY_ERROR: |
| _print_next_block(par_num++, "VAUX PCI CORE"); |
| break; |
| case AEU_INPUTS_ATTN_BITS_DEBUG_PARITY_ERROR: |
| _print_next_block(par_num++, "DEBUG"); |
| break; |
| case AEU_INPUTS_ATTN_BITS_USDM_PARITY_ERROR: |
| _print_next_block(par_num++, "USDM"); |
| break; |
| case AEU_INPUTS_ATTN_BITS_USEMI_PARITY_ERROR: |
| _print_next_block(par_num++, "USEMI"); |
| break; |
| case AEU_INPUTS_ATTN_BITS_UPB_PARITY_ERROR: |
| _print_next_block(par_num++, "UPB"); |
| break; |
| case AEU_INPUTS_ATTN_BITS_CSDM_PARITY_ERROR: |
| _print_next_block(par_num++, "CSDM"); |
| break; |
| } |
| |
| /* Clear the bit */ |
| sig &= ~cur_bit; |
| } |
| } |
| |
| return par_num; |
| } |
| |
| static inline int bnx2x_print_blocks_with_parity2(u32 sig, int par_num) |
| { |
| int i = 0; |
| u32 cur_bit = 0; |
| for (i = 0; sig; i++) { |
| cur_bit = ((u32)0x1 << i); |
| if (sig & cur_bit) { |
| switch (cur_bit) { |
| case AEU_INPUTS_ATTN_BITS_CSEMI_PARITY_ERROR: |
| _print_next_block(par_num++, "CSEMI"); |
| break; |
| case AEU_INPUTS_ATTN_BITS_PXP_PARITY_ERROR: |
| _print_next_block(par_num++, "PXP"); |
| break; |
| case AEU_IN_ATTN_BITS_PXPPCICLOCKCLIENT_PARITY_ERROR: |
| _print_next_block(par_num++, |
| "PXPPCICLOCKCLIENT"); |
| break; |
| case AEU_INPUTS_ATTN_BITS_CFC_PARITY_ERROR: |
| _print_next_block(par_num++, "CFC"); |
| break; |
| case AEU_INPUTS_ATTN_BITS_CDU_PARITY_ERROR: |
| _print_next_block(par_num++, "CDU"); |
| break; |
| case AEU_INPUTS_ATTN_BITS_IGU_PARITY_ERROR: |
| _print_next_block(par_num++, "IGU"); |
| break; |
| case AEU_INPUTS_ATTN_BITS_MISC_PARITY_ERROR: |
| _print_next_block(par_num++, "MISC"); |
| break; |
| } |
| |
| /* Clear the bit */ |
| sig &= ~cur_bit; |
| } |
| } |
| |
| return par_num; |
| } |
| |
| static inline int bnx2x_print_blocks_with_parity3(u32 sig, int par_num) |
| { |
| int i = 0; |
| u32 cur_bit = 0; |
| for (i = 0; sig; i++) { |
| cur_bit = ((u32)0x1 << i); |
| if (sig & cur_bit) { |
| switch (cur_bit) { |
| case AEU_INPUTS_ATTN_BITS_MCP_LATCHED_ROM_PARITY: |
| _print_next_block(par_num++, "MCP ROM"); |
| break; |
| case AEU_INPUTS_ATTN_BITS_MCP_LATCHED_UMP_RX_PARITY: |
| _print_next_block(par_num++, "MCP UMP RX"); |
| break; |
| case AEU_INPUTS_ATTN_BITS_MCP_LATCHED_UMP_TX_PARITY: |
| _print_next_block(par_num++, "MCP UMP TX"); |
| break; |
| case AEU_INPUTS_ATTN_BITS_MCP_LATCHED_SCPAD_PARITY: |
| _print_next_block(par_num++, "MCP SCPAD"); |
| break; |
| } |
| |
| /* Clear the bit */ |
| sig &= ~cur_bit; |
| } |
| } |
| |
| return par_num; |
| } |
| |
| static inline bool bnx2x_parity_attn(struct bnx2x *bp, u32 sig0, u32 sig1, |
| u32 sig2, u32 sig3) |
| { |
| if ((sig0 & HW_PRTY_ASSERT_SET_0) || (sig1 & HW_PRTY_ASSERT_SET_1) || |
| (sig2 & HW_PRTY_ASSERT_SET_2) || (sig3 & HW_PRTY_ASSERT_SET_3)) { |
| int par_num = 0; |
| DP(NETIF_MSG_HW, "Was parity error: HW block parity attention: " |
| "[0]:0x%08x [1]:0x%08x " |
| "[2]:0x%08x [3]:0x%08x\n", |
| sig0 & HW_PRTY_ASSERT_SET_0, |
| sig1 & HW_PRTY_ASSERT_SET_1, |
| sig2 & HW_PRTY_ASSERT_SET_2, |
| sig3 & HW_PRTY_ASSERT_SET_3); |
| printk(KERN_ERR"%s: Parity errors detected in blocks: ", |
| bp->dev->name); |
| par_num = bnx2x_print_blocks_with_parity0( |
| sig0 & HW_PRTY_ASSERT_SET_0, par_num); |
| par_num = bnx2x_print_blocks_with_parity1( |
| sig1 & HW_PRTY_ASSERT_SET_1, par_num); |
| par_num = bnx2x_print_blocks_with_parity2( |
| sig2 & HW_PRTY_ASSERT_SET_2, par_num); |
| par_num = bnx2x_print_blocks_with_parity3( |
| sig3 & HW_PRTY_ASSERT_SET_3, par_num); |
| printk("\n"); |
| return true; |
| } else |
| return false; |
| } |
| |
| bool bnx2x_chk_parity_attn(struct bnx2x *bp) |
| { |
| struct attn_route attn; |
| int port = BP_PORT(bp); |
| |
| attn.sig[0] = REG_RD(bp, |
| MISC_REG_AEU_AFTER_INVERT_1_FUNC_0 + |
| port*4); |
| attn.sig[1] = REG_RD(bp, |
| MISC_REG_AEU_AFTER_INVERT_2_FUNC_0 + |
| port*4); |
| attn.sig[2] = REG_RD(bp, |
| MISC_REG_AEU_AFTER_INVERT_3_FUNC_0 + |
| port*4); |
| attn.sig[3] = REG_RD(bp, |
| MISC_REG_AEU_AFTER_INVERT_4_FUNC_0 + |
| port*4); |
| |
| return bnx2x_parity_attn(bp, attn.sig[0], attn.sig[1], attn.sig[2], |
| attn.sig[3]); |
| } |
| |
| static void bnx2x_attn_int_deasserted(struct bnx2x *bp, u32 deasserted) |
| { |
| struct attn_route attn, *group_mask; |
| int port = BP_PORT(bp); |
| int index; |
| u32 reg_addr; |
| u32 val; |
| u32 aeu_mask; |
| |
| /* need to take HW lock because MCP or other port might also |
| try to handle this event */ |
| bnx2x_acquire_alr(bp); |
| |
| if (bnx2x_chk_parity_attn(bp)) { |
| bp->recovery_state = BNX2X_RECOVERY_INIT; |
| bnx2x_set_reset_in_progress(bp); |
| schedule_delayed_work(&bp->reset_task, 0); |
| /* Disable HW interrupts */ |
| bnx2x_int_disable(bp); |
| bnx2x_release_alr(bp); |
| /* In case of parity errors don't handle attentions so that |
| * other function would "see" parity errors. |
| */ |
| return; |
| } |
| |
| attn.sig[0] = REG_RD(bp, MISC_REG_AEU_AFTER_INVERT_1_FUNC_0 + port*4); |
| attn.sig[1] = REG_RD(bp, MISC_REG_AEU_AFTER_INVERT_2_FUNC_0 + port*4); |
| attn.sig[2] = REG_RD(bp, MISC_REG_AEU_AFTER_INVERT_3_FUNC_0 + port*4); |
| attn.sig[3] = REG_RD(bp, MISC_REG_AEU_AFTER_INVERT_4_FUNC_0 + port*4); |
| DP(NETIF_MSG_HW, "attn: %08x %08x %08x %08x\n", |
| attn.sig[0], attn.sig[1], attn.sig[2], attn.sig[3]); |
| |
| for (index = 0; index < MAX_DYNAMIC_ATTN_GRPS; index++) { |
| if (deasserted & (1 << index)) { |
| group_mask = &bp->attn_group[index]; |
| |
| DP(NETIF_MSG_HW, "group[%d]: %08x %08x %08x %08x\n", |
| index, group_mask->sig[0], group_mask->sig[1], |
| group_mask->sig[2], group_mask->sig[3]); |
| |
| bnx2x_attn_int_deasserted3(bp, |
| attn.sig[3] & group_mask->sig[3]); |
| bnx2x_attn_int_deasserted1(bp, |
| attn.sig[1] & group_mask->sig[1]); |
| bnx2x_attn_int_deasserted2(bp, |
| attn.sig[2] & group_mask->sig[2]); |
| bnx2x_attn_int_deasserted0(bp, |
| attn.sig[0] & group_mask->sig[0]); |
| } |
| } |
| |
| bnx2x_release_alr(bp); |
| |
| reg_addr = (HC_REG_COMMAND_REG + port*32 + COMMAND_REG_ATTN_BITS_CLR); |
| |
| val = ~deasserted; |
| DP(NETIF_MSG_HW, "about to mask 0x%08x at HC addr 0x%x\n", |
| val, reg_addr); |
| REG_WR(bp, reg_addr, val); |
| |
| if (~bp->attn_state & deasserted) |
| BNX2X_ERR("IGU ERROR\n"); |
| |
| reg_addr = port ? MISC_REG_AEU_MASK_ATTN_FUNC_1 : |
| MISC_REG_AEU_MASK_ATTN_FUNC_0; |
| |
| bnx2x_acquire_hw_lock(bp, HW_LOCK_RESOURCE_PORT0_ATT_MASK + port); |
| aeu_mask = REG_RD(bp, reg_addr); |
| |
| DP(NETIF_MSG_HW, "aeu_mask %x newly deasserted %x\n", |
| aeu_mask, deasserted); |
| aeu_mask |= (deasserted & 0x3ff); |
| DP(NETIF_MSG_HW, "new mask %x\n", aeu_mask); |
| |
| REG_WR(bp, reg_addr, aeu_mask); |
| bnx2x_release_hw_lock(bp, HW_LOCK_RESOURCE_PORT0_ATT_MASK + port); |
| |
| DP(NETIF_MSG_HW, "attn_state %x\n", bp->attn_state); |
| bp->attn_state &= ~deasserted; |
| DP(NETIF_MSG_HW, "new state %x\n", bp->attn_state); |
| } |
| |
| static void bnx2x_attn_int(struct bnx2x *bp) |
| { |
| /* read local copy of bits */ |
| u32 attn_bits = le32_to_cpu(bp->def_status_blk->atten_status_block. |
| attn_bits); |
| u32 attn_ack = le32_to_cpu(bp->def_status_blk->atten_status_block. |
| attn_bits_ack); |
| u32 attn_state = bp->attn_state; |
| |
| /* look for changed bits */ |
| u32 asserted = attn_bits & ~attn_ack & ~attn_state; |
| u32 deasserted = ~attn_bits & attn_ack & attn_state; |
| |
| DP(NETIF_MSG_HW, |
| "attn_bits %x attn_ack %x asserted %x deasserted %x\n", |
| attn_bits, attn_ack, asserted, deasserted); |
| |
| if (~(attn_bits ^ attn_ack) & (attn_bits ^ attn_state)) |
| BNX2X_ERR("BAD attention state\n"); |
| |
| /* handle bits that were raised */ |
| if (asserted) |
| bnx2x_attn_int_asserted(bp, asserted); |
| |
| if (deasserted) |
| bnx2x_attn_int_deasserted(bp, deasserted); |
| } |
| |
| static void bnx2x_sp_task(struct work_struct *work) |
| { |
| struct bnx2x *bp = container_of(work, struct bnx2x, sp_task.work); |
| u16 status; |
| |
| /* Return here if interrupt is disabled */ |
| if (unlikely(atomic_read(&bp->intr_sem) != 0)) { |
| DP(NETIF_MSG_INTR, "called but intr_sem not 0, returning\n"); |
| return; |
| } |
| |
| status = bnx2x_update_dsb_idx(bp); |
| /* if (status == 0) */ |
| /* BNX2X_ERR("spurious slowpath interrupt!\n"); */ |
| |
| DP(NETIF_MSG_INTR, "got a slowpath interrupt (status 0x%x)\n", status); |
| |
| /* HW attentions */ |
| if (status & 0x1) { |
| bnx2x_attn_int(bp); |
| status &= ~0x1; |
| } |
| |
| /* CStorm events: STAT_QUERY */ |
| if (status & 0x2) { |
| DP(BNX2X_MSG_SP, "CStorm events: STAT_QUERY\n"); |
| status &= ~0x2; |
| } |
| |
| if (unlikely(status)) |
| DP(NETIF_MSG_INTR, "got an unknown interrupt! (status 0x%x)\n", |
| status); |
| |
| bnx2x_ack_sb(bp, DEF_SB_ID, ATTENTION_ID, le16_to_cpu(bp->def_att_idx), |
| IGU_INT_NOP, 1); |
| bnx2x_ack_sb(bp, DEF_SB_ID, USTORM_ID, le16_to_cpu(bp->def_u_idx), |
| IGU_INT_NOP, 1); |
| bnx2x_ack_sb(bp, DEF_SB_ID, CSTORM_ID, le16_to_cpu(bp->def_c_idx), |
| IGU_INT_NOP, 1); |
| bnx2x_ack_sb(bp, DEF_SB_ID, XSTORM_ID, le16_to_cpu(bp->def_x_idx), |
| IGU_INT_NOP, 1); |
| bnx2x_ack_sb(bp, DEF_SB_ID, TSTORM_ID, le16_to_cpu(bp->def_t_idx), |
| IGU_INT_ENABLE, 1); |
| } |
| |
| irqreturn_t bnx2x_msix_sp_int(int irq, void *dev_instance) |
| { |
| struct net_device *dev = dev_instance; |
| struct bnx2x *bp = netdev_priv(dev); |
| |
| /* Return here if interrupt is disabled */ |
| if (unlikely(atomic_read(&bp->intr_sem) != 0)) { |
| DP(NETIF_MSG_INTR, "called but intr_sem not 0, returning\n"); |
| return IRQ_HANDLED; |
| } |
| |
| bnx2x_ack_sb(bp, DEF_SB_ID, TSTORM_ID, 0, IGU_INT_DISABLE, 0); |
| |
| #ifdef BNX2X_STOP_ON_ERROR |
| if (unlikely(bp->panic)) |
| return IRQ_HANDLED; |
| #endif |
| |
| #ifdef BCM_CNIC |
| { |
| struct cnic_ops *c_ops; |
| |
| rcu_read_lock(); |
| c_ops = rcu_dereference(bp->cnic_ops); |
| if (c_ops) |
| c_ops->cnic_handler(bp->cnic_data, NULL); |
| rcu_read_unlock(); |
| } |
| #endif |
| queue_delayed_work(bnx2x_wq, &bp->sp_task, 0); |
| |
| return IRQ_HANDLED; |
| } |
| |
| /* end of slow path */ |
| |
| static void bnx2x_timer(unsigned long data) |
| { |
| struct bnx2x *bp = (struct bnx2x *) data; |
| |
| if (!netif_running(bp->dev)) |
| return; |
| |
| if (atomic_read(&bp->intr_sem) != 0) |
| goto timer_restart; |
| |
| if (poll) { |
| struct bnx2x_fastpath *fp = &bp->fp[0]; |
| int rc; |
| |
| bnx2x_tx_int(fp); |
| rc = bnx2x_rx_int(fp, 1000); |
| } |
| |
| if (!BP_NOMCP(bp)) { |
| int func = BP_FUNC(bp); |
| u32 drv_pulse; |
| u32 mcp_pulse; |
| |
| ++bp->fw_drv_pulse_wr_seq; |
| bp->fw_drv_pulse_wr_seq &= DRV_PULSE_SEQ_MASK; |
| /* TBD - add SYSTEM_TIME */ |
| drv_pulse = bp->fw_drv_pulse_wr_seq; |
| SHMEM_WR(bp, func_mb[func].drv_pulse_mb, drv_pulse); |
| |
| mcp_pulse = (SHMEM_RD(bp, func_mb[func].mcp_pulse_mb) & |
| MCP_PULSE_SEQ_MASK); |
| /* The delta between driver pulse and mcp response |
| * should be 1 (before mcp response) or 0 (after mcp response) |
| */ |
| if ((drv_pulse != mcp_pulse) && |
| (drv_pulse != ((mcp_pulse + 1) & MCP_PULSE_SEQ_MASK))) { |
| /* someone lost a heartbeat... */ |
| BNX2X_ERR("drv_pulse (0x%x) != mcp_pulse (0x%x)\n", |
| drv_pulse, mcp_pulse); |
| } |
| } |
| |
| if (bp->state == BNX2X_STATE_OPEN) |
| bnx2x_stats_handle(bp, STATS_EVENT_UPDATE); |
| |
| timer_restart: |
| mod_timer(&bp->timer, jiffies + bp->current_interval); |
| } |
| |
| /* end of Statistics */ |
| |
| /* nic init */ |
| |
| /* |
| * nic init service functions |
| */ |
| |
| static void bnx2x_zero_sb(struct bnx2x *bp, int sb_id) |
| { |
| int port = BP_PORT(bp); |
| |
| /* "CSTORM" */ |
| bnx2x_init_fill(bp, CSEM_REG_FAST_MEMORY + |
| CSTORM_SB_HOST_STATUS_BLOCK_U_OFFSET(port, sb_id), 0, |
| CSTORM_SB_STATUS_BLOCK_U_SIZE / 4); |
| bnx2x_init_fill(bp, CSEM_REG_FAST_MEMORY + |
| CSTORM_SB_HOST_STATUS_BLOCK_C_OFFSET(port, sb_id), 0, |
| CSTORM_SB_STATUS_BLOCK_C_SIZE / 4); |
| } |
| |
| void bnx2x_init_sb(struct bnx2x *bp, struct host_status_block *sb, |
| dma_addr_t mapping, int sb_id) |
| { |
| int port = BP_PORT(bp); |
| int func = BP_FUNC(bp); |
| int index; |
| u64 section; |
| |
| /* USTORM */ |
| section = ((u64)mapping) + offsetof(struct host_status_block, |
| u_status_block); |
| sb->u_status_block.status_block_id = sb_id; |
| |
| REG_WR(bp, BAR_CSTRORM_INTMEM + |
| CSTORM_SB_HOST_SB_ADDR_U_OFFSET(port, sb_id), U64_LO(section)); |
| REG_WR(bp, BAR_CSTRORM_INTMEM + |
| ((CSTORM_SB_HOST_SB_ADDR_U_OFFSET(port, sb_id)) + 4), |
| U64_HI(section)); |
| REG_WR8(bp, BAR_CSTRORM_INTMEM + FP_USB_FUNC_OFF + |
| CSTORM_SB_HOST_STATUS_BLOCK_U_OFFSET(port, sb_id), func); |
| |
| for (index = 0; index < HC_USTORM_SB_NUM_INDICES; index++) |
| REG_WR16(bp, BAR_CSTRORM_INTMEM + |
| CSTORM_SB_HC_DISABLE_U_OFFSET(port, sb_id, index), 1); |
| |
| /* CSTORM */ |
| section = ((u64)mapping) + offsetof(struct host_status_block, |
| c_status_block); |
| sb->c_status_block.status_block_id = sb_id; |
| |
| REG_WR(bp, BAR_CSTRORM_INTMEM + |
| CSTORM_SB_HOST_SB_ADDR_C_OFFSET(port, sb_id), U64_LO(section)); |
| REG_WR(bp, BAR_CSTRORM_INTMEM + |
| ((CSTORM_SB_HOST_SB_ADDR_C_OFFSET(port, sb_id)) + 4), |
| U64_HI(section)); |
| REG_WR8(bp, BAR_CSTRORM_INTMEM + FP_CSB_FUNC_OFF + |
| CSTORM_SB_HOST_STATUS_BLOCK_C_OFFSET(port, sb_id), func); |
| |
| for (index = 0; index < HC_CSTORM_SB_NUM_INDICES; index++) |
| REG_WR16(bp, BAR_CSTRORM_INTMEM + |
| CSTORM_SB_HC_DISABLE_C_OFFSET(port, sb_id, index), 1); |
| |
| bnx2x_ack_sb(bp, sb_id, CSTORM_ID, 0, IGU_INT_ENABLE, 0); |
| } |
| |
| static void bnx2x_zero_def_sb(struct bnx2x *bp) |
| { |
| int func = BP_FUNC(bp); |
| |
| bnx2x_init_fill(bp, TSEM_REG_FAST_MEMORY + |
| TSTORM_DEF_SB_HOST_STATUS_BLOCK_OFFSET(func), 0, |
| sizeof(struct tstorm_def_status_block)/4); |
| bnx2x_init_fill(bp, CSEM_REG_FAST_MEMORY + |
| CSTORM_DEF_SB_HOST_STATUS_BLOCK_U_OFFSET(func), 0, |
| sizeof(struct cstorm_def_status_block_u)/4); |
| bnx2x_init_fill(bp, CSEM_REG_FAST_MEMORY + |
| CSTORM_DEF_SB_HOST_STATUS_BLOCK_C_OFFSET(func), 0, |
| sizeof(struct cstorm_def_status_block_c)/4); |
| bnx2x_init_fill(bp, XSEM_REG_FAST_MEMORY + |
| XSTORM_DEF_SB_HOST_STATUS_BLOCK_OFFSET(func), 0, |
| sizeof(struct xstorm_def_status_block)/4); |
| } |
| |
| static void bnx2x_init_def_sb(struct bnx2x *bp, |
| struct host_def_status_block *def_sb, |
| dma_addr_t mapping, int sb_id) |
| { |
| int port = BP_PORT(bp); |
| int func = BP_FUNC(bp); |
| int index, val, reg_offset; |
| u64 section; |
| |
| /* ATTN */ |
| section = ((u64)mapping) + offsetof(struct host_def_status_block, |
| atten_status_block); |
| def_sb->atten_status_block.status_block_id = sb_id; |
| |
| bp->attn_state = 0; |
| |
| reg_offset = (port ? MISC_REG_AEU_ENABLE1_FUNC_1_OUT_0 : |
| MISC_REG_AEU_ENABLE1_FUNC_0_OUT_0); |
| |
| for (index = 0; index < MAX_DYNAMIC_ATTN_GRPS; index++) { |
| bp->attn_group[index].sig[0] = REG_RD(bp, |
| reg_offset + 0x10*index); |
| bp->attn_group[index].sig[1] = REG_RD(bp, |
| reg_offset + 0x4 + 0x10*index); |
| bp->attn_group[index].sig[2] = REG_RD(bp, |
| reg_offset + 0x8 + 0x10*index); |
| bp->attn_group[index].sig[3] = REG_RD(bp, |
| reg_offset + 0xc + 0x10*index); |
| } |
| |
| reg_offset = (port ? HC_REG_ATTN_MSG1_ADDR_L : |
| HC_REG_ATTN_MSG0_ADDR_L); |
| |
| REG_WR(bp, reg_offset, U64_LO(section)); |
| REG_WR(bp, reg_offset + 4, U64_HI(section)); |
| |
| reg_offset = (port ? HC_REG_ATTN_NUM_P1 : HC_REG_ATTN_NUM_P0); |
| |
| val = REG_RD(bp, reg_offset); |
| val |= sb_id; |
| REG_WR(bp, reg_offset, val); |
| |
| /* USTORM */ |
| section = ((u64)mapping) + offsetof(struct host_def_status_block, |
| u_def_status_block); |
| def_sb->u_def_status_block.status_block_id = sb_id; |
| |
| REG_WR(bp, BAR_CSTRORM_INTMEM + |
| CSTORM_DEF_SB_HOST_SB_ADDR_U_OFFSET(func), U64_LO(section)); |
| REG_WR(bp, BAR_CSTRORM_INTMEM + |
| ((CSTORM_DEF_SB_HOST_SB_ADDR_U_OFFSET(func)) + 4), |
| U64_HI(section)); |
| REG_WR8(bp, BAR_CSTRORM_INTMEM + DEF_USB_FUNC_OFF + |
| CSTORM_DEF_SB_HOST_STATUS_BLOCK_U_OFFSET(func), func); |
| |
| for (index = 0; index < HC_USTORM_DEF_SB_NUM_INDICES; index++) |
| REG_WR16(bp, BAR_CSTRORM_INTMEM + |
| CSTORM_DEF_SB_HC_DISABLE_U_OFFSET(func, index), 1); |
| |
| /* CSTORM */ |
| section = ((u64)mapping) + offsetof(struct host_def_status_block, |
| c_def_status_block); |
| def_sb->c_def_status_block.status_block_id = sb_id; |
| |
| REG_WR(bp, BAR_CSTRORM_INTMEM + |
| CSTORM_DEF_SB_HOST_SB_ADDR_C_OFFSET(func), U64_LO(section)); |
| REG_WR(bp, BAR_CSTRORM_INTMEM + |
| ((CSTORM_DEF_SB_HOST_SB_ADDR_C_OFFSET(func)) + 4), |
| U64_HI(section)); |
| REG_WR8(bp, BAR_CSTRORM_INTMEM + DEF_CSB_FUNC_OFF + |
| CSTORM_DEF_SB_HOST_STATUS_BLOCK_C_OFFSET(func), func); |
| |
| for (index = 0; index < HC_CSTORM_DEF_SB_NUM_INDICES; index++) |
| REG_WR16(bp, BAR_CSTRORM_INTMEM + |
| CSTORM_DEF_SB_HC_DISABLE_C_OFFSET(func, index), 1); |
| |
| /* TSTORM */ |
| section = ((u64)mapping) + offsetof(struct host_def_status_block, |
| t_def_status_block); |
| def_sb->t_def_status_block.status_block_id = sb_id; |
| |
| REG_WR(bp, BAR_TSTRORM_INTMEM + |
| TSTORM_DEF_SB_HOST_SB_ADDR_OFFSET(func), U64_LO(section)); |
| REG_WR(bp, BAR_TSTRORM_INTMEM + |
| ((TSTORM_DEF_SB_HOST_SB_ADDR_OFFSET(func)) + 4), |
| U64_HI(section)); |
| REG_WR8(bp, BAR_TSTRORM_INTMEM + DEF_TSB_FUNC_OFF + |
| TSTORM_DEF_SB_HOST_STATUS_BLOCK_OFFSET(func), func); |
| |
| for (index = 0; index < HC_TSTORM_DEF_SB_NUM_INDICES; index++) |
| REG_WR16(bp, BAR_TSTRORM_INTMEM + |
| TSTORM_DEF_SB_HC_DISABLE_OFFSET(func, index), 1); |
| |
| /* XSTORM */ |
| section = ((u64)mapping) + offsetof(struct host_def_status_block, |
| x_def_status_block); |
| def_sb->x_def_status_block.status_block_id = sb_id; |
| |
| REG_WR(bp, BAR_XSTRORM_INTMEM + |
| XSTORM_DEF_SB_HOST_SB_ADDR_OFFSET(func), U64_LO(section)); |
| REG_WR(bp, BAR_XSTRORM_INTMEM + |
| ((XSTORM_DEF_SB_HOST_SB_ADDR_OFFSET(func)) + 4), |
| U64_HI(section)); |
| REG_WR8(bp, BAR_XSTRORM_INTMEM + DEF_XSB_FUNC_OFF + |
| XSTORM_DEF_SB_HOST_STATUS_BLOCK_OFFSET(func), func); |
| |
| for (index = 0; index < HC_XSTORM_DEF_SB_NUM_INDICES; index++) |
| REG_WR16(bp, BAR_XSTRORM_INTMEM + |
| XSTORM_DEF_SB_HC_DISABLE_OFFSET(func, index), 1); |
| |
| bp->stats_pending = 0; |
| bp->set_mac_pending = 0; |
| |
| bnx2x_ack_sb(bp, sb_id, CSTORM_ID, 0, IGU_INT_ENABLE, 0); |
| } |
| |
| void bnx2x_update_coalesce(struct bnx2x *bp) |
| { |
| int port = BP_PORT(bp); |
| int i; |
| |
| for_each_queue(bp, i) { |
| int sb_id = bp->fp[i].sb_id; |
| |
| /* HC_INDEX_U_ETH_RX_CQ_CONS */ |
| REG_WR8(bp, BAR_CSTRORM_INTMEM + |
| CSTORM_SB_HC_TIMEOUT_U_OFFSET(port, sb_id, |
| U_SB_ETH_RX_CQ_INDEX), |
| bp->rx_ticks/(4 * BNX2X_BTR)); |
| REG_WR16(bp, BAR_CSTRORM_INTMEM + |
| CSTORM_SB_HC_DISABLE_U_OFFSET(port, sb_id, |
| U_SB_ETH_RX_CQ_INDEX), |
| (bp->rx_ticks/(4 * BNX2X_BTR)) ? 0 : 1); |
| |
| /* HC_INDEX_C_ETH_TX_CQ_CONS */ |
| REG_WR8(bp, BAR_CSTRORM_INTMEM + |
| CSTORM_SB_HC_TIMEOUT_C_OFFSET(port, sb_id, |
| C_SB_ETH_TX_CQ_INDEX), |
| bp->tx_ticks/(4 * BNX2X_BTR)); |
| REG_WR16(bp, BAR_CSTRORM_INTMEM + |
| CSTORM_SB_HC_DISABLE_C_OFFSET(port, sb_id, |
| C_SB_ETH_TX_CQ_INDEX), |
| (bp->tx_ticks/(4 * BNX2X_BTR)) ? 0 : 1); |
| } |
| } |
| |
| static void bnx2x_init_sp_ring(struct bnx2x *bp) |
| { |
| int func = BP_FUNC(bp); |
| |
| spin_lock_init(&bp->spq_lock); |
| |
| bp->spq_left = MAX_SPQ_PENDING; |
| bp->spq_prod_idx = 0; |
| bp->dsb_sp_prod = BNX2X_SP_DSB_INDEX; |
| bp->spq_prod_bd = bp->spq; |
| bp->spq_last_bd = bp->spq_prod_bd + MAX_SP_DESC_CNT; |
| |
| REG_WR(bp, XSEM_REG_FAST_MEMORY + XSTORM_SPQ_PAGE_BASE_OFFSET(func), |
| U64_LO(bp->spq_mapping)); |
| REG_WR(bp, |
| XSEM_REG_FAST_MEMORY + XSTORM_SPQ_PAGE_BASE_OFFSET(func) + 4, |
| U64_HI(bp->spq_mapping)); |
| |
| REG_WR(bp, XSEM_REG_FAST_MEMORY + XSTORM_SPQ_PROD_OFFSET(func), |
| bp->spq_prod_idx); |
| } |
| |
| static void bnx2x_init_context(struct bnx2x *bp) |
| { |
| int i; |
| |
| /* Rx */ |
| for_each_queue(bp, i) { |
| struct eth_context *context = bnx2x_sp(bp, context[i].eth); |
| struct bnx2x_fastpath *fp = &bp->fp[i]; |
| u8 cl_id = fp->cl_id; |
| |
| context->ustorm_st_context.common.sb_index_numbers = |
| BNX2X_RX_SB_INDEX_NUM; |
| context->ustorm_st_context.common.clientId = cl_id; |
| context->ustorm_st_context.common.status_block_id = fp->sb_id; |
| context->ustorm_st_context.common.flags = |
| (USTORM_ETH_ST_CONTEXT_CONFIG_ENABLE_MC_ALIGNMENT | |
| USTORM_ETH_ST_CONTEXT_CONFIG_ENABLE_STATISTICS); |
| context->ustorm_st_context.common.statistics_counter_id = |
| cl_id; |
| context->ustorm_st_context.common.mc_alignment_log_size = |
| BNX2X_RX_ALIGN_SHIFT; |
| context->ustorm_st_context.common.bd_buff_size = |
| bp->rx_buf_size; |
| context->ustorm_st_context.common.bd_page_base_hi = |
| U64_HI(fp->rx_desc_mapping); |
| context->ustorm_st_context.common.bd_page_base_lo = |
| U64_LO(fp->rx_desc_mapping); |
| if (!fp->disable_tpa) { |
| context->ustorm_st_context.common.flags |= |
| USTORM_ETH_ST_CONTEXT_CONFIG_ENABLE_TPA; |
| context->ustorm_st_context.common.sge_buff_size = |
| (u16)min_t(u32, SGE_PAGE_SIZE*PAGES_PER_SGE, |
| 0xffff); |
| context->ustorm_st_context.common.sge_page_base_hi = |
| U64_HI(fp->rx_sge_mapping); |
| context->ustorm_st_context.common.sge_page_base_lo = |
| U64_LO(fp->rx_sge_mapping); |
| |
| context->ustorm_st_context.common.max_sges_for_packet = |
| SGE_PAGE_ALIGN(bp->dev->mtu) >> SGE_PAGE_SHIFT; |
| context->ustorm_st_context.common.max_sges_for_packet = |
| ((context->ustorm_st_context.common. |
| max_sges_for_packet + PAGES_PER_SGE - 1) & |
| (~(PAGES_PER_SGE - 1))) >> PAGES_PER_SGE_SHIFT; |
| } |
| |
| context->ustorm_ag_context.cdu_usage = |
| CDU_RSRVD_VALUE_TYPE_A(HW_CID(bp, i), |
| CDU_REGION_NUMBER_UCM_AG, |
| ETH_CONNECTION_TYPE); |
| |
| context->xstorm_ag_context.cdu_reserved = |
| CDU_RSRVD_VALUE_TYPE_A(HW_CID(bp, i), |
| CDU_REGION_NUMBER_XCM_AG, |
| ETH_CONNECTION_TYPE); |
| } |
| |
| /* Tx */ |
| for_each_queue(bp, i) { |
| struct bnx2x_fastpath *fp = &bp->fp[i]; |
| struct eth_context *context = |
| bnx2x_sp(bp, context[i].eth); |
| |
| context->cstorm_st_context.sb_index_number = |
| C_SB_ETH_TX_CQ_INDEX; |
| context->cstorm_st_context.status_block_id = fp->sb_id; |
| |
| context->xstorm_st_context.tx_bd_page_base_hi = |
| U64_HI(fp->tx_desc_mapping); |
| context->xstorm_st_context.tx_bd_page_base_lo = |
| U64_LO(fp->tx_desc_mapping); |
| context->xstorm_st_context.statistics_data = (fp->cl_id | |
| XSTORM_ETH_ST_CONTEXT_STATISTICS_ENABLE); |
| } |
| } |
| |
| static void bnx2x_init_ind_table(struct bnx2x *bp) |
| { |
| int func = BP_FUNC(bp); |
| int i; |
| |
| if (bp->multi_mode == ETH_RSS_MODE_DISABLED) |
| return; |
| |
| DP(NETIF_MSG_IFUP, |
| "Initializing indirection table multi_mode %d\n", bp->multi_mode); |
| for (i = 0; i < TSTORM_INDIRECTION_TABLE_SIZE; i++) |
| REG_WR8(bp, BAR_TSTRORM_INTMEM + |
| TSTORM_INDIRECTION_TABLE_OFFSET(func) + i, |
| bp->fp->cl_id + (i % bp->num_queues)); |
| } |
| |
| void bnx2x_set_client_config(struct bnx2x *bp) |
| { |
| struct tstorm_eth_client_config tstorm_client = {0}; |
| int port = BP_PORT(bp); |
| int i; |
| |
| tstorm_client.mtu = bp->dev->mtu; |
| tstorm_client.config_flags = |
| (TSTORM_ETH_CLIENT_CONFIG_STATSITICS_ENABLE | |
| TSTORM_ETH_CLIENT_CONFIG_E1HOV_REM_ENABLE); |
| #ifdef BCM_VLAN |
| if (bp->rx_mode && bp->vlgrp && (bp->flags & HW_VLAN_RX_FLAG)) { |
| tstorm_client.config_flags |= |
| TSTORM_ETH_CLIENT_CONFIG_VLAN_REM_ENABLE; |
| DP(NETIF_MSG_IFUP, "vlan removal enabled\n"); |
| } |
| #endif |
| |
| for_each_queue(bp, i) { |
| tstorm_client.statistics_counter_id = bp->fp[i].cl_id; |
| |
| REG_WR(bp, BAR_TSTRORM_INTMEM + |
| TSTORM_CLIENT_CONFIG_OFFSET(port, bp->fp[i].cl_id), |
| ((u32 *)&tstorm_client)[0]); |
| REG_WR(bp, BAR_TSTRORM_INTMEM + |
| TSTORM_CLIENT_CONFIG_OFFSET(port, bp->fp[i].cl_id) + 4, |
| ((u32 *)&tstorm_client)[1]); |
| } |
| |
| DP(BNX2X_MSG_OFF, "tstorm_client: 0x%08x 0x%08x\n", |
| ((u32 *)&tstorm_client)[0], ((u32 *)&tstorm_client)[1]); |
| } |
| |
| void bnx2x_set_storm_rx_mode(struct bnx2x *bp) |
| { |
| struct tstorm_eth_mac_filter_config tstorm_mac_filter = {0}; |
| int mode = bp->rx_mode; |
| int mask = bp->rx_mode_cl_mask; |
| int func = BP_FUNC(bp); |
| int port = BP_PORT(bp); |
| int i; |
| /* All but management unicast packets should pass to the host as well */ |
| u32 llh_mask = |
| NIG_LLH0_BRB1_DRV_MASK_REG_LLH0_BRB1_DRV_MASK_BRCST | |
| NIG_LLH0_BRB1_DRV_MASK_REG_LLH0_BRB1_DRV_MASK_MLCST | |
| NIG_LLH0_BRB1_DRV_MASK_REG_LLH0_BRB1_DRV_MASK_VLAN | |
| NIG_LLH0_BRB1_DRV_MASK_REG_LLH0_BRB1_DRV_MASK_NO_VLAN; |
| |
| DP(NETIF_MSG_IFUP, "rx mode %d mask 0x%x\n", mode, mask); |
| |
| switch (mode) { |
| case BNX2X_RX_MODE_NONE: /* no Rx */ |
| tstorm_mac_filter.ucast_drop_all = mask; |
| tstorm_mac_filter.mcast_drop_all = mask; |
| tstorm_mac_filter.bcast_drop_all = mask; |
| break; |
| |
| case BNX2X_RX_MODE_NORMAL: |
| tstorm_mac_filter.bcast_accept_all = mask; |
| break; |
| |
| case BNX2X_RX_MODE_ALLMULTI: |
| tstorm_mac_filter.mcast_accept_all = mask; |
| tstorm_mac_filter.bcast_accept_all = mask; |
| break; |
| |
| case BNX2X_RX_MODE_PROMISC: |
| tstorm_mac_filter.ucast_accept_all = mask; |
| tstorm_mac_filter.mcast_accept_all = mask; |
| tstorm_mac_filter.bcast_accept_all = mask; |
| /* pass management unicast packets as well */ |
| llh_mask |= NIG_LLH0_BRB1_DRV_MASK_REG_LLH0_BRB1_DRV_MASK_UNCST; |
| break; |
| |
| default: |
| BNX2X_ERR("BAD rx mode (%d)\n", mode); |
| break; |
| } |
| |
| REG_WR(bp, |
| (port ? NIG_REG_LLH1_BRB1_DRV_MASK : NIG_REG_LLH0_BRB1_DRV_MASK), |
| llh_mask); |
| |
| for (i = 0; i < sizeof(struct tstorm_eth_mac_filter_config)/4; i++) { |
| REG_WR(bp, BAR_TSTRORM_INTMEM + |
| TSTORM_MAC_FILTER_CONFIG_OFFSET(func) + i * 4, |
| ((u32 *)&tstorm_mac_filter)[i]); |
| |
| /* DP(NETIF_MSG_IFUP, "tstorm_mac_filter[%d]: 0x%08x\n", i, |
| ((u32 *)&tstorm_mac_filter)[i]); */ |
| } |
| |
| if (mode != BNX2X_RX_MODE_NONE) |
| bnx2x_set_client_config(bp); |
| } |
| |
| static void bnx2x_init_internal_common(struct bnx2x *bp) |
| { |
| int i; |
| |
| /* Zero this manually as its initialization is |
| currently missing in the initTool */ |
| for (i = 0; i < (USTORM_AGG_DATA_SIZE >> 2); i++) |
| REG_WR(bp, BAR_USTRORM_INTMEM + |
| USTORM_AGG_DATA_OFFSET + i * 4, 0); |
| } |
| |
| static void bnx2x_init_internal_port(struct bnx2x *bp) |
| { |
| int port = BP_PORT(bp); |
| |
| REG_WR(bp, |
| BAR_CSTRORM_INTMEM + CSTORM_HC_BTR_U_OFFSET(port), BNX2X_BTR); |
| REG_WR(bp, |
| BAR_CSTRORM_INTMEM + CSTORM_HC_BTR_C_OFFSET(port), BNX2X_BTR); |
| REG_WR(bp, BAR_TSTRORM_INTMEM + TSTORM_HC_BTR_OFFSET(port), BNX2X_BTR); |
| REG_WR(bp, BAR_XSTRORM_INTMEM + XSTORM_HC_BTR_OFFSET(port), BNX2X_BTR); |
| } |
| |
| static void bnx2x_init_internal_func(struct bnx2x *bp) |
| { |
| struct tstorm_eth_function_common_config tstorm_config = {0}; |
| struct stats_indication_flags stats_flags = {0}; |
| int port = BP_PORT(bp); |
| int func = BP_FUNC(bp); |
| int i, j; |
| u32 offset; |
| u16 max_agg_size; |
| |
| tstorm_config.config_flags = RSS_FLAGS(bp); |
| |
| if (is_multi(bp)) |
| tstorm_config.rss_result_mask = MULTI_MASK; |
| |
| /* Enable TPA if needed */ |
| if (bp->flags & TPA_ENABLE_FLAG) |
| tstorm_config.config_flags |= |
| TSTORM_ETH_FUNCTION_COMMON_CONFIG_ENABLE_TPA; |
| |
| if (IS_E1HMF(bp)) |
| tstorm_config.config_flags |= |
| TSTORM_ETH_FUNCTION_COMMON_CONFIG_E1HOV_IN_CAM; |
| |
| tstorm_config.leading_client_id = BP_L_ID(bp); |
| |
| REG_WR(bp, BAR_TSTRORM_INTMEM + |
| TSTORM_FUNCTION_COMMON_CONFIG_OFFSET(func), |
| (*(u32 *)&tstorm_config)); |
| |
| bp->rx_mode = BNX2X_RX_MODE_NONE; /* no rx until link is up */ |
| bp->rx_mode_cl_mask = (1 << BP_L_ID(bp)); |
| bnx2x_set_storm_rx_mode(bp); |
| |
| for_each_queue(bp, i) { |
| u8 cl_id = bp->fp[i].cl_id; |
| |
| /* reset xstorm per client statistics */ |
| offset = BAR_XSTRORM_INTMEM + |
| XSTORM_PER_COUNTER_ID_STATS_OFFSET(port, cl_id); |
| for (j = 0; |
| j < sizeof(struct xstorm_per_client_stats) / 4; j++) |
| REG_WR(bp, offset + j*4, 0); |
| |
| /* reset tstorm per client statistics */ |
| offset = BAR_TSTRORM_INTMEM + |
| TSTORM_PER_COUNTER_ID_STATS_OFFSET(port, cl_id); |
| for (j = 0; |
| j < sizeof(struct tstorm_per_client_stats) / 4; j++) |
| REG_WR(bp, offset + j*4, 0); |
| |
| /* reset ustorm per client statistics */ |
| offset = BAR_USTRORM_INTMEM + |
| USTORM_PER_COUNTER_ID_STATS_OFFSET(port, cl_id); |
| for (j = 0; |
| j < sizeof(struct ustorm_per_client_stats) / 4; j++) |
| REG_WR(bp, offset + j*4, 0); |
| } |
| |
| /* Init statistics related context */ |
| stats_flags.collect_eth = 1; |
| |
| REG_WR(bp, BAR_XSTRORM_INTMEM + XSTORM_STATS_FLAGS_OFFSET(func), |
| ((u32 *)&stats_flags)[0]); |
| REG_WR(bp, BAR_XSTRORM_INTMEM + XSTORM_STATS_FLAGS_OFFSET(func) + 4, |
| ((u32 *)&stats_flags)[1]); |
| |
| REG_WR(bp, BAR_TSTRORM_INTMEM + TSTORM_STATS_FLAGS_OFFSET(func), |
| ((u32 *)&stats_flags)[0]); |
| REG_WR(bp, BAR_TSTRORM_INTMEM + TSTORM_STATS_FLAGS_OFFSET(func) + 4, |
| ((u32 *)&stats_flags)[1]); |
| |
| REG_WR(bp, BAR_USTRORM_INTMEM + USTORM_STATS_FLAGS_OFFSET(func), |
| ((u32 *)&stats_flags)[0]); |
| REG_WR(bp, BAR_USTRORM_INTMEM + USTORM_STATS_FLAGS_OFFSET(func) + 4, |
| ((u32 *)&stats_flags)[1]); |
| |
| REG_WR(bp, BAR_CSTRORM_INTMEM + CSTORM_STATS_FLAGS_OFFSET(func), |
| ((u32 *)&stats_flags)[0]); |
| REG_WR(bp, BAR_CSTRORM_INTMEM + CSTORM_STATS_FLAGS_OFFSET(func) + 4, |
| ((u32 *)&stats_flags)[1]); |
| |
| REG_WR(bp, BAR_XSTRORM_INTMEM + |
| XSTORM_ETH_STATS_QUERY_ADDR_OFFSET(func), |
| U64_LO(bnx2x_sp_mapping(bp, fw_stats))); |
| REG_WR(bp, BAR_XSTRORM_INTMEM + |
| XSTORM_ETH_STATS_QUERY_ADDR_OFFSET(func) + 4, |
| U64_HI(bnx2x_sp_mapping(bp, fw_stats))); |
| |
| REG_WR(bp, BAR_TSTRORM_INTMEM + |
| TSTORM_ETH_STATS_QUERY_ADDR_OFFSET(func), |
| U64_LO(bnx2x_sp_mapping(bp, fw_stats))); |
| REG_WR(bp, BAR_TSTRORM_INTMEM + |
| TSTORM_ETH_STATS_QUERY_ADDR_OFFSET(func) + 4, |
| U64_HI(bnx2x_sp_mapping(bp, fw_stats))); |
| |
| REG_WR(bp, BAR_USTRORM_INTMEM + |
| USTORM_ETH_STATS_QUERY_ADDR_OFFSET(func), |
| U64_LO(bnx2x_sp_mapping(bp, fw_stats))); |
| REG_WR(bp, BAR_USTRORM_INTMEM + |
| USTORM_ETH_STATS_QUERY_ADDR_OFFSET(func) + 4, |
| U64_HI(bnx2x_sp_mapping(bp, fw_stats))); |
| |
| if (CHIP_IS_E1H(bp)) { |
| REG_WR8(bp, BAR_XSTRORM_INTMEM + XSTORM_FUNCTION_MODE_OFFSET, |
| IS_E1HMF(bp)); |
| REG_WR8(bp, BAR_TSTRORM_INTMEM + TSTORM_FUNCTION_MODE_OFFSET, |
| IS_E1HMF(bp)); |
| REG_WR8(bp, BAR_CSTRORM_INTMEM + CSTORM_FUNCTION_MODE_OFFSET, |
| IS_E1HMF(bp)); |
| REG_WR8(bp, BAR_USTRORM_INTMEM + USTORM_FUNCTION_MODE_OFFSET, |
| IS_E1HMF(bp)); |
| |
| REG_WR16(bp, BAR_XSTRORM_INTMEM + XSTORM_E1HOV_OFFSET(func), |
| bp->e1hov); |
| } |
| |
| /* Init CQ ring mapping and aggregation size, the FW limit is 8 frags */ |
| max_agg_size = min_t(u32, (min_t(u32, 8, MAX_SKB_FRAGS) * |
| SGE_PAGE_SIZE * PAGES_PER_SGE), 0xffff); |
| for_each_queue(bp, i) { |
| struct bnx2x_fastpath *fp = &bp->fp[i]; |
| |
| REG_WR(bp, BAR_USTRORM_INTMEM + |
| USTORM_CQE_PAGE_BASE_OFFSET(port, fp->cl_id), |
| U64_LO(fp->rx_comp_mapping)); |
| REG_WR(bp, BAR_USTRORM_INTMEM + |
| USTORM_CQE_PAGE_BASE_OFFSET(port, fp->cl_id) + 4, |
| U64_HI(fp->rx_comp_mapping)); |
| |
| /* Next page */ |
| REG_WR(bp, BAR_USTRORM_INTMEM + |
| USTORM_CQE_PAGE_NEXT_OFFSET(port, fp->cl_id), |
| U64_LO(fp->rx_comp_mapping + BCM_PAGE_SIZE)); |
| REG_WR(bp, BAR_USTRORM_INTMEM + |
| USTORM_CQE_PAGE_NEXT_OFFSET(port, fp->cl_id) + 4, |
| U64_HI(fp->rx_comp_mapping + BCM_PAGE_SIZE)); |
| |
| REG_WR16(bp, BAR_USTRORM_INTMEM + |
| USTORM_MAX_AGG_SIZE_OFFSET(port, fp->cl_id), |
| max_agg_size); |
| } |
| |
| /* dropless flow control */ |
| if (CHIP_IS_E1H(bp)) { |
| struct ustorm_eth_rx_pause_data_e1h rx_pause = {0}; |
| |
| rx_pause.bd_thr_low = 250; |
| rx_pause.cqe_thr_low = 250; |
| rx_pause.cos = 1; |
| rx_pause.sge_thr_low = 0; |
| rx_pause.bd_thr_high = 350; |
| rx_pause.cqe_thr_high = 350; |
| rx_pause.sge_thr_high = 0; |
| |
| for_each_queue(bp, i) { |
| struct bnx2x_fastpath *fp = &bp->fp[i]; |
| |
| if (!fp->disable_tpa) { |
| rx_pause.sge_thr_low = 150; |
| rx_pause.sge_thr_high = 250; |
| } |
| |
| |
| offset = BAR_USTRORM_INTMEM + |
| USTORM_ETH_RING_PAUSE_DATA_OFFSET(port, |
| fp->cl_id); |
| for (j = 0; |
| j < sizeof(struct ustorm_eth_rx_pause_data_e1h)/4; |
| j++) |
| REG_WR(bp, offset + j*4, |
| ((u32 *)&rx_pause)[j]); |
| } |
| } |
| |
| memset(&(bp->cmng), 0, sizeof(struct cmng_struct_per_port)); |
| |
| /* Init rate shaping and fairness contexts */ |
| if (IS_E1HMF(bp)) { |
| int vn; |
| |
| /* During init there is no active link |
| Until link is up, set link rate to 10Gbps */ |
| bp->link_vars.line_speed = SPEED_10000; |
| bnx2x_init_port_minmax(bp); |
| |
| if (!BP_NOMCP(bp)) |
| bp->mf_config = |
| SHMEM_RD(bp, mf_cfg.func_mf_config[func].config); |
| bnx2x_calc_vn_weight_sum(bp); |
| |
| for (vn = VN_0; vn < E1HVN_MAX; vn++) |
| bnx2x_init_vn_minmax(bp, 2*vn + port); |
| |
| /* Enable rate shaping and fairness */ |
| bp->cmng.flags.cmng_enables |= |
| CMNG_FLAGS_PER_PORT_RATE_SHAPING_VN; |
| |
| } else { |
| /* rate shaping and fairness are disabled */ |
| DP(NETIF_MSG_IFUP, |
| "single function mode minmax will be disabled\n"); |
| } |
| |
| |
| /* Store cmng structures to internal memory */ |
| if (bp->port.pmf) |
| for (i = 0; i < sizeof(struct cmng_struct_per_port) / 4; i++) |
| REG_WR(bp, BAR_XSTRORM_INTMEM + |
| XSTORM_CMNG_PER_PORT_VARS_OFFSET(port) + i * 4, |
| ((u32 *)(&bp->cmng))[i]); |
| } |
| |
| static void bnx2x_init_internal(struct bnx2x *bp, u32 load_code) |
| { |
| switch (load_code) { |
| case FW_MSG_CODE_DRV_LOAD_COMMON: |
| bnx2x_init_internal_common(bp); |
| /* no break */ |
| |
| case FW_MSG_CODE_DRV_LOAD_PORT: |
| bnx2x_init_internal_port(bp); |
| /* no break */ |
| |
| case FW_MSG_CODE_DRV_LOAD_FUNCTION: |
| bnx2x_init_internal_func(bp); |
| break; |
| |
| default: |
| BNX2X_ERR("Unknown load_code (0x%x) from MCP\n", load_code); |
| break; |
| } |
| } |
| |
| void bnx2x_nic_init(struct bnx2x *bp, u32 load_code) |
| { |
| int i; |
| |
| for_each_queue(bp, i) { |
| struct bnx2x_fastpath *fp = &bp->fp[i]; |
| |
| fp->bp = bp; |
| fp->state = BNX2X_FP_STATE_CLOSED; |
| fp->index = i; |
| fp->cl_id = BP_L_ID(bp) + i; |
| #ifdef BCM_CNIC |
| fp->sb_id = fp->cl_id + 1; |
| #else |
| fp->sb_id = fp->cl_id; |
| #endif |
| DP(NETIF_MSG_IFUP, |
| "queue[%d]: bnx2x_init_sb(%p,%p) cl_id %d sb %d\n", |
| i, bp, fp->status_blk, fp->cl_id, fp->sb_id); |
| bnx2x_init_sb(bp, fp->status_blk, fp->status_blk_mapping, |
| fp->sb_id); |
| bnx2x_update_fpsb_idx(fp); |
| } |
| |
| /* ensure status block indices were read */ |
| rmb(); |
| |
| |
| bnx2x_init_def_sb(bp, bp->def_status_blk, bp->def_status_blk_mapping, |
| DEF_SB_ID); |
| bnx2x_update_dsb_idx(bp); |
| bnx2x_update_coalesce(bp); |
| bnx2x_init_rx_rings(bp); |
| bnx2x_init_tx_ring(bp); |
| bnx2x_init_sp_ring(bp); |
| bnx2x_init_context(bp); |
| bnx2x_init_internal(bp, load_code); |
| bnx2x_init_ind_table(bp); |
| bnx2x_stats_init(bp); |
| |
| /* At this point, we are ready for interrupts */ |
| atomic_set(&bp->intr_sem, 0); |
| |
| /* flush all before enabling interrupts */ |
| mb(); |
| mmiowb(); |
| |
| bnx2x_int_enable(bp); |
| |
| /* Check for SPIO5 */ |
| bnx2x_attn_int_deasserted0(bp, |
| REG_RD(bp, MISC_REG_AEU_AFTER_INVERT_1_FUNC_0 + BP_PORT(bp)*4) & |
| AEU_INPUTS_ATTN_BITS_SPIO5); |
| } |
| |
| /* end of nic init */ |
| |
| /* |
| * gzip service functions |
| */ |
| |
| static int bnx2x_gunzip_init(struct bnx2x *bp) |
| { |
| bp->gunzip_buf = dma_alloc_coherent(&bp->pdev->dev, FW_BUF_SIZE, |
| &bp->gunzip_mapping, GFP_KERNEL); |
| if (bp->gunzip_buf == NULL) |
| goto gunzip_nomem1; |
| |
| bp->strm = kmalloc(sizeof(*bp->strm), GFP_KERNEL); |
| if (bp->strm == NULL) |
| goto gunzip_nomem2; |
| |
| bp->strm->workspace = kmalloc(zlib_inflate_workspacesize(), |
| GFP_KERNEL); |
| if (bp->strm->workspace == NULL) |
| goto gunzip_nomem3; |
| |
| return 0; |
| |
| gunzip_nomem3: |
| kfree(bp->strm); |
| bp->strm = NULL; |
| |
| gunzip_nomem2: |
| dma_free_coherent(&bp->pdev->dev, FW_BUF_SIZE, bp->gunzip_buf, |
| bp->gunzip_mapping); |
| bp->gunzip_buf = NULL; |
| |
| gunzip_nomem1: |
| netdev_err(bp->dev, "Cannot allocate firmware buffer for" |
| " un-compression\n"); |
| return -ENOMEM; |
| } |
| |
| static void bnx2x_gunzip_end(struct bnx2x *bp) |
| { |
| kfree(bp->strm->workspace); |
| |
| kfree(bp->strm); |
| bp->strm = NULL; |
| |
| if (bp->gunzip_buf) { |
| dma_free_coherent(&bp->pdev->dev, FW_BUF_SIZE, bp->gunzip_buf, |
| bp->gunzip_mapping); |
| bp->gunzip_buf = NULL; |
| } |
| } |
| |
| static int bnx2x_gunzip(struct bnx2x *bp, const u8 *zbuf, int len) |
| { |
| int n, rc; |
| |
| /* check gzip header */ |
| if ((zbuf[0] != 0x1f) || (zbuf[1] != 0x8b) || (zbuf[2] != Z_DEFLATED)) { |
| BNX2X_ERR("Bad gzip header\n"); |
| return -EINVAL; |
| } |
| |
| n = 10; |
| |
| #define FNAME 0x8 |
| |
| if (zbuf[3] & FNAME) |
| while ((zbuf[n++] != 0) && (n < len)); |
| |
| bp->strm->next_in = (typeof(bp->strm->next_in))zbuf + n; |
| bp->strm->avail_in = len - n; |
| bp->strm->next_out = bp->gunzip_buf; |
| bp->strm->avail_out = FW_BUF_SIZE; |
| |
| rc = zlib_inflateInit2(bp->strm, -MAX_WBITS); |
| if (rc != Z_OK) |
| return rc; |
| |
| rc = zlib_inflate(bp->strm, Z_FINISH); |
| if ((rc != Z_OK) && (rc != Z_STREAM_END)) |
| netdev_err(bp->dev, "Firmware decompression error: %s\n", |
| bp->strm->msg); |
| |
| bp->gunzip_outlen = (FW_BUF_SIZE - bp->strm->avail_out); |
| if (bp->gunzip_outlen & 0x3) |
| netdev_err(bp->dev, "Firmware decompression error:" |
| " gunzip_outlen (%d) not aligned\n", |
| bp->gunzip_outlen); |
| bp->gunzip_outlen >>= 2; |
| |
| zlib_inflateEnd(bp->strm); |
| |
| if (rc == Z_STREAM_END) |
| return 0; |
| |
| return rc; |
| } |
| |
| /* nic load/unload */ |
| |
| /* |
| * General service functions |
| */ |
| |
| /* send a NIG loopback debug packet */ |
| static void bnx2x_lb_pckt(struct bnx2x *bp) |
| { |
| u32 wb_write[3]; |
| |
| /* Ethernet source and destination addresses */ |
| wb_write[0] = 0x55555555; |
| wb_write[1] = 0x55555555; |
| wb_write[2] = 0x20; /* SOP */ |
| REG_WR_DMAE(bp, NIG_REG_DEBUG_PACKET_LB, wb_write, 3); |
| |
| /* NON-IP protocol */ |
| wb_write[0] = 0x09000000; |
| wb_write[1] = 0x55555555; |
| wb_write[2] = 0x10; /* EOP, eop_bvalid = 0 */ |
| REG_WR_DMAE(bp, NIG_REG_DEBUG_PACKET_LB, wb_write, 3); |
| } |
| |
| /* some of the internal memories |
| * are not directly readable from the driver |
| * to test them we send debug packets |
| */ |
| static int bnx2x_int_mem_test(struct bnx2x *bp) |
| { |
| int factor; |
| int count, i; |
| u32 val = 0; |
| |
| if (CHIP_REV_IS_FPGA(bp)) |
| factor = 120; |
| else if (CHIP_REV_IS_EMUL(bp)) |
| factor = 200; |
| else |
| factor = 1; |
| |
| DP(NETIF_MSG_HW, "start part1\n"); |
| |
| /* Disable inputs of parser neighbor blocks */ |
| REG_WR(bp, TSDM_REG_ENABLE_IN1, 0x0); |
| REG_WR(bp, TCM_REG_PRS_IFEN, 0x0); |
| REG_WR(bp, CFC_REG_DEBUG0, 0x1); |
| REG_WR(bp, NIG_REG_PRS_REQ_IN_EN, 0x0); |
| |
| /* Write 0 to parser credits for CFC search request */ |
| REG_WR(bp, PRS_REG_CFC_SEARCH_INITIAL_CREDIT, 0x0); |
| |
| /* send Ethernet packet */ |
| bnx2x_lb_pckt(bp); |
| |
| /* TODO do i reset NIG statistic? */ |
| /* Wait until NIG register shows 1 packet of size 0x10 */ |
| count = 1000 * factor; |
| while (count) { |
| |
| bnx2x_read_dmae(bp, NIG_REG_STAT2_BRB_OCTET, 2); |
| val = *bnx2x_sp(bp, wb_data[0]); |
| if (val == 0x10) |
| break; |
| |
| msleep(10); |
| count--; |
| } |
| if (val != 0x10) { |
| BNX2X_ERR("NIG timeout val = 0x%x\n", val); |
| return -1; |
| } |
| |
| /* Wait until PRS register shows 1 packet */ |
| count = 1000 * factor; |
| while (count) { |
| val = REG_RD(bp, PRS_REG_NUM_OF_PACKETS); |
| if (val == 1) |
| break; |
| |
| msleep(10); |
| count--; |
| } |
| if (val != 0x1) { |
| BNX2X_ERR("PRS timeout val = 0x%x\n", val); |
| return -2; |
| } |
| |
| /* Reset and init BRB, PRS */ |
| REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_1_CLEAR, 0x03); |
| msleep(50); |
| REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_1_SET, 0x03); |
| msleep(50); |
| bnx2x_init_block(bp, BRB1_BLOCK, COMMON_STAGE); |
| bnx2x_init_block(bp, PRS_BLOCK, COMMON_STAGE); |
| |
| DP(NETIF_MSG_HW, "part2\n"); |
| |
| /* Disable inputs of parser neighbor blocks */ |
| REG_WR(bp, TSDM_REG_ENABLE_IN1, 0x0); |
| REG_WR(bp, TCM_REG_PRS_IFEN, 0x0); |
| REG_WR(bp, CFC_REG_DEBUG0, 0x1); |
| REG_WR(bp, NIG_REG_PRS_REQ_IN_EN, 0x0); |
| |
| /* Write 0 to parser credits for CFC search request */ |
| REG_WR(bp, PRS_REG_CFC_SEARCH_INITIAL_CREDIT, 0x0); |
| |
| /* send 10 Ethernet packets */ |
| for (i = 0; i < 10; i++) |
| bnx2x_lb_pckt(bp); |
| |
| /* Wait until NIG register shows 10 + 1 |
| packets of size 11*0x10 = 0xb0 */ |
| count = 1000 * factor; |
| while (count) { |
| |
| bnx2x_read_dmae(bp, NIG_REG_STAT2_BRB_OCTET, 2); |
| val = *bnx2x_sp(bp, wb_data[0]); |
| if (val == 0xb0) |
| break; |
| |
| msleep(10); |
| count--; |
| } |
| if (val != 0xb0) { |
| BNX2X_ERR("NIG timeout val = 0x%x\n", val); |
| return -3; |
| } |
| |
| /* Wait until PRS register shows 2 packets */ |
| val = REG_RD(bp, PRS_REG_NUM_OF_PACKETS); |
| if (val != 2) |
| BNX2X_ERR("PRS timeout val = 0x%x\n", val); |
| |
| /* Write 1 to parser credits for CFC search request */ |
| REG_WR(bp, PRS_REG_CFC_SEARCH_INITIAL_CREDIT, 0x1); |
| |
| /* Wait until PRS register shows 3 packets */ |
| msleep(10 * factor); |
| /* Wait until NIG register shows 1 packet of size 0x10 */ |
| val = REG_RD(bp, PRS_REG_NUM_OF_PACKETS); |
| if (val != 3) |
| BNX2X_ERR("PRS timeout val = 0x%x\n", val); |
| |
| /* clear NIG EOP FIFO */ |
| for (i = 0; i < 11; i++) |
| REG_RD(bp, NIG_REG_INGRESS_EOP_LB_FIFO); |
| val = REG_RD(bp, NIG_REG_INGRESS_EOP_LB_EMPTY); |
| if (val != 1) { |
| BNX2X_ERR("clear of NIG failed\n"); |
| return -4; |
| } |
| |
| /* Reset and init BRB, PRS, NIG */ |
| REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_1_CLEAR, 0x03); |
| msleep(50); |
| REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_1_SET, 0x03); |
| msleep(50); |
| bnx2x_init_block(bp, BRB1_BLOCK, COMMON_STAGE); |
| bnx2x_init_block(bp, PRS_BLOCK, COMMON_STAGE); |
| #ifndef BCM_CNIC |
| /* set NIC mode */ |
| REG_WR(bp, PRS_REG_NIC_MODE, 1); |
| #endif |
| |
| /* Enable inputs of parser neighbor blocks */ |
| REG_WR(bp, TSDM_REG_ENABLE_IN1, 0x7fffffff); |
| REG_WR(bp, TCM_REG_PRS_IFEN, 0x1); |
| REG_WR(bp, CFC_REG_DEBUG0, 0x0); |
| REG_WR(bp, NIG_REG_PRS_REQ_IN_EN, 0x1); |
| |
| DP(NETIF_MSG_HW, "done\n"); |
| |
| return 0; /* OK */ |
| } |
| |
| static void enable_blocks_attention(struct bnx2x *bp) |
| { |
| REG_WR(bp, PXP_REG_PXP_INT_MASK_0, 0); |
| REG_WR(bp, PXP_REG_PXP_INT_MASK_1, 0); |
| REG_WR(bp, DORQ_REG_DORQ_INT_MASK, 0); |
| REG_WR(bp, CFC_REG_CFC_INT_MASK, 0); |
| REG_WR(bp, QM_REG_QM_INT_MASK, 0); |
| REG_WR(bp, TM_REG_TM_INT_MASK, 0); |
| REG_WR(bp, XSDM_REG_XSDM_INT_MASK_0, 0); |
| REG_WR(bp, XSDM_REG_XSDM_INT_MASK_1, 0); |
| REG_WR(bp, XCM_REG_XCM_INT_MASK, 0); |
| /* REG_WR(bp, XSEM_REG_XSEM_INT_MASK_0, 0); */ |
| /* REG_WR(bp, XSEM_REG_XSEM_INT_MASK_1, 0); */ |
| REG_WR(bp, USDM_REG_USDM_INT_MASK_0, 0); |
| REG_WR(bp, USDM_REG_USDM_INT_MASK_1, 0); |
| REG_WR(bp, UCM_REG_UCM_INT_MASK, 0); |
| /* REG_WR(bp, USEM_REG_USEM_INT_MASK_0, 0); */ |
| /* REG_WR(bp, USEM_REG_USEM_INT_MASK_1, 0); */ |
| REG_WR(bp, GRCBASE_UPB + PB_REG_PB_INT_MASK, 0); |
| REG_WR(bp, CSDM_REG_CSDM_INT_MASK_0, 0); |
| REG_WR(bp, CSDM_REG_CSDM_INT_MASK_1, 0); |
| REG_WR(bp, CCM_REG_CCM_INT_MASK, 0); |
| /* REG_WR(bp, CSEM_REG_CSEM_INT_MASK_0, 0); */ |
| /* REG_WR(bp, CSEM_REG_CSEM_INT_MASK_1, 0); */ |
| if (CHIP_REV_IS_FPGA(bp)) |
| REG_WR(bp, PXP2_REG_PXP2_INT_MASK_0, 0x580000); |
| else |
| REG_WR(bp, PXP2_REG_PXP2_INT_MASK_0, 0x480000); |
| REG_WR(bp, TSDM_REG_TSDM_INT_MASK_0, 0); |
| REG_WR(bp, TSDM_REG_TSDM_INT_MASK_1, 0); |
| REG_WR(bp, TCM_REG_TCM_INT_MASK, 0); |
| /* REG_WR(bp, TSEM_REG_TSEM_INT_MASK_0, 0); */ |
| /* REG_WR(bp, TSEM_REG_TSEM_INT_MASK_1, 0); */ |
| REG_WR(bp, CDU_REG_CDU_INT_MASK, 0); |
| REG_WR(bp, DMAE_REG_DMAE_INT_MASK, 0); |
| /* REG_WR(bp, MISC_REG_MISC_INT_MASK, 0); */ |
| REG_WR(bp, PBF_REG_PBF_INT_MASK, 0X18); /* bit 3,4 masked */ |
| } |
| |
| static const struct { |
| u32 addr; |
| u32 mask; |
| } bnx2x_parity_mask[] = { |
| {PXP_REG_PXP_PRTY_MASK, 0xffffffff}, |
| {PXP2_REG_PXP2_PRTY_MASK_0, 0xffffffff}, |
| {PXP2_REG_PXP2_PRTY_MASK_1, 0xffffffff}, |
| {HC_REG_HC_PRTY_MASK, 0xffffffff}, |
| {MISC_REG_MISC_PRTY_MASK, 0xffffffff}, |
| {QM_REG_QM_PRTY_MASK, 0x0}, |
| {DORQ_REG_DORQ_PRTY_MASK, 0x0}, |
| {GRCBASE_UPB + PB_REG_PB_PRTY_MASK, 0x0}, |
| {GRCBASE_XPB + PB_REG_PB_PRTY_MASK, 0x0}, |
| {SRC_REG_SRC_PRTY_MASK, 0x4}, /* bit 2 */ |
| {CDU_REG_CDU_PRTY_MASK, 0x0}, |
| {CFC_REG_CFC_PRTY_MASK, 0x0}, |
| {DBG_REG_DBG_PRTY_MASK, 0x0}, |
| {DMAE_REG_DMAE_PRTY_MASK, 0x0}, |
| {BRB1_REG_BRB1_PRTY_MASK, 0x0}, |
| {PRS_REG_PRS_PRTY_MASK, (1<<6)},/* bit 6 */ |
| {TSDM_REG_TSDM_PRTY_MASK, 0x18},/* bit 3,4 */ |
| {CSDM_REG_CSDM_PRTY_MASK, 0x8}, /* bit 3 */ |
| {USDM_REG_USDM_PRTY_MASK, 0x38},/* bit 3,4,5 */ |
| {XSDM_REG_XSDM_PRTY_MASK, 0x8}, /* bit 3 */ |
| {TSEM_REG_TSEM_PRTY_MASK_0, 0x0}, |
| {TSEM_REG_TSEM_PRTY_MASK_1, 0x0}, |
| {USEM_REG_USEM_PRTY_MASK_0, 0x0}, |
| {USEM_REG_USEM_PRTY_MASK_1, 0x0}, |
| {CSEM_REG_CSEM_PRTY_MASK_0, 0x0}, |
| {CSEM_REG_CSEM_PRTY_MASK_1, 0x0}, |
| {XSEM_REG_XSEM_PRTY_MASK_0, 0x0}, |
| {XSEM_REG_XSEM_PRTY_MASK_1, 0x0} |
| }; |
| |
| static void enable_blocks_parity(struct bnx2x *bp) |
| { |
| int i; |
| |
| for (i = 0; i < ARRAY_SIZE(bnx2x_parity_mask); i++) |
| REG_WR(bp, bnx2x_parity_mask[i].addr, |
| bnx2x_parity_mask[i].mask); |
| } |
| |
| |
| static void bnx2x_reset_common(struct bnx2x *bp) |
| { |
| /* reset_common */ |
| REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_1_CLEAR, |
| 0xd3ffff7f); |
| REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR, 0x1403); |
| } |
| |
| static void bnx2x_init_pxp(struct bnx2x *bp) |
| { |
| u16 devctl; |
| int r_order, w_order; |
| |
| pci_read_config_word(bp->pdev, |
| bp->pcie_cap + PCI_EXP_DEVCTL, &devctl); |
| DP(NETIF_MSG_HW, "read 0x%x from devctl\n", devctl); |
| w_order = ((devctl & PCI_EXP_DEVCTL_PAYLOAD) >> 5); |
| if (bp->mrrs == -1) |
| r_order = ((devctl & PCI_EXP_DEVCTL_READRQ) >> 12); |
| else { |
| DP(NETIF_MSG_HW, "force read order to %d\n", bp->mrrs); |
| r_order = bp->mrrs; |
| } |
| |
| bnx2x_init_pxp_arb(bp, r_order, w_order); |
| } |
| |
| static void bnx2x_setup_fan_failure_detection(struct bnx2x *bp) |
| { |
| int is_required; |
| u32 val; |
| int port; |
| |
| if (BP_NOMCP(bp)) |
| return; |
| |
| is_required = 0; |
| val = SHMEM_RD(bp, dev_info.shared_hw_config.config2) & |
| SHARED_HW_CFG_FAN_FAILURE_MASK; |
| |
| if (val == SHARED_HW_CFG_FAN_FAILURE_ENABLED) |
| is_required = 1; |
| |
| /* |
| * The fan failure mechanism is usually related to the PHY type since |
| * the power consumption of the board is affected by the PHY. Currently, |
| * fan is required for most designs with SFX7101, BCM8727 and BCM8481. |
| */ |
| else if (val == SHARED_HW_CFG_FAN_FAILURE_PHY_TYPE) |
| for (port = PORT_0; port < PORT_MAX; port++) { |
| is_required |= |
| bnx2x_fan_failure_det_req( |
| bp, |
| bp->common.shmem_base, |
| bp->common.shmem2_base, |
| port); |
| } |
| |
| DP(NETIF_MSG_HW, "fan detection setting: %d\n", is_required); |
| |
| if (is_required == 0) |
| return; |
| |
| /* Fan failure is indicated by SPIO 5 */ |
| bnx2x_set_spio(bp, MISC_REGISTERS_SPIO_5, |
| MISC_REGISTERS_SPIO_INPUT_HI_Z); |
| |
| /* set to active low mode */ |
| val = REG_RD(bp, MISC_REG_SPIO_INT); |
| val |= ((1 << MISC_REGISTERS_SPIO_5) << |
| MISC_REGISTERS_SPIO_INT_OLD_SET_POS); |
| REG_WR(bp, MISC_REG_SPIO_INT, val); |
| |
| /* enable interrupt to signal the IGU */ |
| val = REG_RD(bp, MISC_REG_SPIO_EVENT_EN); |
| val |= (1 << MISC_REGISTERS_SPIO_5); |
| REG_WR(bp, MISC_REG_SPIO_EVENT_EN, val); |
| } |
| |
| static int bnx2x_init_common(struct bnx2x *bp) |
| { |
| u32 val, i; |
| #ifdef BCM_CNIC |
| u32 wb_write[2]; |
| #endif |
| |
| DP(BNX2X_MSG_MCP, "starting common init func %d\n", BP_FUNC(bp)); |
| |
| bnx2x_reset_common(bp); |
| REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_1_SET, 0xffffffff); |
| REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_SET, 0xfffc); |
| |
| bnx2x_init_block(bp, MISC_BLOCK, COMMON_STAGE); |
| if (CHIP_IS_E1H(bp)) |
| REG_WR(bp, MISC_REG_E1HMF_MODE, IS_E1HMF(bp)); |
| |
| REG_WR(bp, MISC_REG_LCPLL_CTRL_REG_2, 0x100); |
| msleep(30); |
| REG_WR(bp, MISC_REG_LCPLL_CTRL_REG_2, 0x0); |
| |
| bnx2x_init_block(bp, PXP_BLOCK, COMMON_STAGE); |
| if (CHIP_IS_E1(bp)) { |
| /* enable HW interrupt from PXP on USDM overflow |
| bit 16 on INT_MASK_0 */ |
| REG_WR(bp, PXP_REG_PXP_INT_MASK_0, 0); |
| } |
| |
| bnx2x_init_block(bp, PXP2_BLOCK, COMMON_STAGE); |
| bnx2x_init_pxp(bp); |
| |
| #ifdef __BIG_ENDIAN |
| REG_WR(bp, PXP2_REG_RQ_QM_ENDIAN_M, 1); |
| REG_WR(bp, PXP2_REG_RQ_TM_ENDIAN_M, 1); |
| REG_WR(bp, PXP2_REG_RQ_SRC_ENDIAN_M, 1); |
| REG_WR(bp, PXP2_REG_RQ_CDU_ENDIAN_M, 1); |
| REG_WR(bp, PXP2_REG_RQ_DBG_ENDIAN_M, 1); |
| /* make sure this value is 0 */ |
| REG_WR(bp, PXP2_REG_RQ_HC_ENDIAN_M, 0); |
| |
| /* REG_WR(bp, PXP2_REG_RD_PBF_SWAP_MODE, 1); */ |
| REG_WR(bp, PXP2_REG_RD_QM_SWAP_MODE, 1); |
| REG_WR(bp, PXP2_REG_RD_TM_SWAP_MODE, 1); |
| REG_WR(bp, PXP2_REG_RD_SRC_SWAP_MODE, 1); |
| REG_WR(bp, PXP2_REG_RD_CDURD_SWAP_MODE, 1); |
| #endif |
| |
| REG_WR(bp, PXP2_REG_RQ_CDU_P_SIZE, 2); |
| #ifdef BCM_CNIC |
| REG_WR(bp, PXP2_REG_RQ_TM_P_SIZE, 5); |
| REG_WR(bp, PXP2_REG_RQ_QM_P_SIZE, 5); |
| REG_WR(bp, PXP2_REG_RQ_SRC_P_SIZE, 5); |
| #endif |
| |
| if (CHIP_REV_IS_FPGA(bp) && CHIP_IS_E1H(bp)) |
| REG_WR(bp, PXP2_REG_PGL_TAGS_LIMIT, 0x1); |
| |
| /* let the HW do it's magic ... */ |
| msleep(100); |
| /* finish PXP init */ |
| val = REG_RD(bp, PXP2_REG_RQ_CFG_DONE); |
| if (val != 1) { |
| BNX2X_ERR("PXP2 CFG failed\n"); |
| return -EBUSY; |
| } |
| val = REG_RD(bp, PXP2_REG_RD_INIT_DONE); |
| if (val != 1) { |
| BNX2X_ERR("PXP2 RD_INIT failed\n"); |
| return -EBUSY; |
| } |
| |
| REG_WR(bp, PXP2_REG_RQ_DISABLE_INPUTS, 0); |
| REG_WR(bp, PXP2_REG_RD_DISABLE_INPUTS, 0); |
| |
| bnx2x_init_block(bp, DMAE_BLOCK, COMMON_STAGE); |
| |
| /* clean the DMAE memory */ |
| bp->dmae_ready = 1; |
| bnx2x_init_fill(bp, TSEM_REG_PRAM, 0, 8); |
| |
| bnx2x_init_block(bp, TCM_BLOCK, COMMON_STAGE); |
| bnx2x_init_block(bp, UCM_BLOCK, COMMON_STAGE); |
| bnx2x_init_block(bp, CCM_BLOCK, COMMON_STAGE); |
| bnx2x_init_block(bp, XCM_BLOCK, COMMON_STAGE); |
| |
| bnx2x_read_dmae(bp, XSEM_REG_PASSIVE_BUFFER, 3); |
| bnx2x_read_dmae(bp, CSEM_REG_PASSIVE_BUFFER, 3); |
| bnx2x_read_dmae(bp, TSEM_REG_PASSIVE_BUFFER, 3); |
| bnx2x_read_dmae(bp, USEM_REG_PASSIVE_BUFFER, 3); |
| |
| bnx2x_init_block(bp, QM_BLOCK, COMMON_STAGE); |
| |
| #ifdef BCM_CNIC |
| wb_write[0] = 0; |
| wb_write[1] = 0; |
| for (i = 0; i < 64; i++) { |
| REG_WR(bp, QM_REG_BASEADDR + i*4, 1024 * 4 * (i%16)); |
| bnx2x_init_ind_wr(bp, QM_REG_PTRTBL + i*8, wb_write, 2); |
| |
| if (CHIP_IS_E1H(bp)) { |
| REG_WR(bp, QM_REG_BASEADDR_EXT_A + i*4, 1024*4*(i%16)); |
| bnx2x_init_ind_wr(bp, QM_REG_PTRTBL_EXT_A + i*8, |
| wb_write, 2); |
| } |
| } |
| #endif |
| /* soft reset pulse */ |
| REG_WR(bp, QM_REG_SOFT_RESET, 1); |
| REG_WR(bp, QM_REG_SOFT_RESET, 0); |
| |
| #ifdef BCM_CNIC |
| bnx2x_init_block(bp, TIMERS_BLOCK, COMMON_STAGE); |
| #endif |
| |
| bnx2x_init_block(bp, DQ_BLOCK, COMMON_STAGE); |
| REG_WR(bp, DORQ_REG_DPM_CID_OFST, BCM_PAGE_SHIFT); |
| if (!CHIP_REV_IS_SLOW(bp)) { |
| /* enable hw interrupt from doorbell Q */ |
| REG_WR(bp, DORQ_REG_DORQ_INT_MASK, 0); |
| } |
| |
| bnx2x_init_block(bp, BRB1_BLOCK, COMMON_STAGE); |
| bnx2x_init_block(bp, PRS_BLOCK, COMMON_STAGE); |
| REG_WR(bp, PRS_REG_A_PRSU_20, 0xf); |
| #ifndef BCM_CNIC |
| /* set NIC mode */ |
| REG_WR(bp, PRS_REG_NIC_MODE, 1); |
| #endif |
| if (CHIP_IS_E1H(bp)) |
| REG_WR(bp, PRS_REG_E1HOV_MODE, IS_E1HMF(bp)); |
| |
| bnx2x_init_block(bp, TSDM_BLOCK, COMMON_STAGE); |
| bnx2x_init_block(bp, CSDM_BLOCK, COMMON_STAGE); |
| bnx2x_init_block(bp, USDM_BLOCK, COMMON_STAGE); |
| bnx2x_init_block(bp, XSDM_BLOCK, COMMON_STAGE); |
| |
| bnx2x_init_fill(bp, TSEM_REG_FAST_MEMORY, 0, STORM_INTMEM_SIZE(bp)); |
| bnx2x_init_fill(bp, USEM_REG_FAST_MEMORY, 0, STORM_INTMEM_SIZE(bp)); |
| bnx2x_init_fill(bp, CSEM_REG_FAST_MEMORY, 0, STORM_INTMEM_SIZE(bp)); |
| bnx2x_init_fill(bp, XSEM_REG_FAST_MEMORY, 0, STORM_INTMEM_SIZE(bp)); |
| |
| bnx2x_init_block(bp, TSEM_BLOCK, COMMON_STAGE); |
| bnx2x_init_block(bp, USEM_BLOCK, COMMON_STAGE); |
| bnx2x_init_block(bp, CSEM_BLOCK, COMMON_STAGE); |
| bnx2x_init_block(bp, XSEM_BLOCK, COMMON_STAGE); |
| |
| /* sync semi rtc */ |
| REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_1_CLEAR, |
| 0x80000000); |
| REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_1_SET, |
| 0x80000000); |
| |
| bnx2x_init_block(bp, UPB_BLOCK, COMMON_STAGE); |
| bnx2x_init_block(bp, XPB_BLOCK, COMMON_STAGE); |
| bnx2x_init_block(bp, PBF_BLOCK, COMMON_STAGE); |
| |
| REG_WR(bp, SRC_REG_SOFT_RST, 1); |
| for (i = SRC_REG_KEYRSS0_0; i <= SRC_REG_KEYRSS1_9; i += 4) |
| REG_WR(bp, i, random32()); |
| bnx2x_init_block(bp, SRCH_BLOCK, COMMON_STAGE); |
| #ifdef BCM_CNIC |
| REG_WR(bp, SRC_REG_KEYSEARCH_0, 0x63285672); |
| REG_WR(bp, SRC_REG_KEYSEARCH_1, 0x24b8f2cc); |
| REG_WR(bp, SRC_REG_KEYSEARCH_2, 0x223aef9b); |
| REG_WR(bp, SRC_REG_KEYSEARCH_3, 0x26001e3a); |
| REG_WR(bp, SRC_REG_KEYSEARCH_4, 0x7ae91116); |
| REG_WR(bp, SRC_REG_KEYSEARCH_5, 0x5ce5230b); |
| REG_WR(bp, SRC_REG_KEYSEARCH_6, 0x298d8adf); |
| REG_WR(bp, SRC_REG_KEYSEARCH_7, 0x6eb0ff09); |
| REG_WR(bp, SRC_REG_KEYSEARCH_8, 0x1830f82f); |
| REG_WR(bp, SRC_REG_KEYSEARCH_9, 0x01e46be7); |
| #endif |
| REG_WR(bp, SRC_REG_SOFT_RST, 0); |
| |
| if (sizeof(union cdu_context) != 1024) |
| /* we currently assume that a context is 1024 bytes */ |
| dev_alert(&bp->pdev->dev, "please adjust the size " |
| "of cdu_context(%ld)\n", |
| (long)sizeof(union cdu_context)); |
| |
| bnx2x_init_block(bp, CDU_BLOCK, COMMON_STAGE); |
| val = (4 << 24) + (0 << 12) + 1024; |
| REG_WR(bp, CDU_REG_CDU_GLOBAL_PARAMS, val); |
| |
| bnx2x_init_block(bp, CFC_BLOCK, COMMON_STAGE); |
| REG_WR(bp, CFC_REG_INIT_REG, 0x7FF); |
| /* enable context validation interrupt from CFC */ |
| REG_WR(bp, CFC_REG_CFC_INT_MASK, 0); |
| |
| /* set the thresholds to prevent CFC/CDU race */ |
| REG_WR(bp, CFC_REG_DEBUG0, 0x20020000); |
| |
| bnx2x_init_block(bp, HC_BLOCK, COMMON_STAGE); |
| bnx2x_init_block(bp, MISC_AEU_BLOCK, COMMON_STAGE); |
| |
| bnx2x_init_block(bp, PXPCS_BLOCK, COMMON_STAGE); |
| /* Reset PCIE errors for debug */ |
| REG_WR(bp, 0x2814, 0xffffffff); |
| REG_WR(bp, 0x3820, 0xffffffff); |
| |
| bnx2x_init_block(bp, EMAC0_BLOCK, COMMON_STAGE); |
| bnx2x_init_block(bp, EMAC1_BLOCK, COMMON_STAGE); |
| bnx2x_init_block(bp, DBU_BLOCK, COMMON_STAGE); |
| bnx2x_init_block(bp, DBG_BLOCK, COMMON_STAGE); |
| |
| bnx2x_init_block(bp, NIG_BLOCK, COMMON_STAGE); |
| if (CHIP_IS_E1H(bp)) { |
| REG_WR(bp, NIG_REG_LLH_MF_MODE, IS_E1HMF(bp)); |
| REG_WR(bp, NIG_REG_LLH_E1HOV_MODE, IS_E1HMF(bp)); |
| } |
| |
| if (CHIP_REV_IS_SLOW(bp)) |
| msleep(200); |
| |
| /* finish CFC init */ |
| val = reg_poll(bp, CFC_REG_LL_INIT_DONE, 1, 100, 10); |
| if (val != 1) { |
| BNX2X_ERR("CFC LL_INIT failed\n"); |
| return -EBUSY; |
| } |
| val = reg_poll(bp, CFC_REG_AC_INIT_DONE, 1, 100, 10); |
| if (val != 1) { |
| BNX2X_ERR("CFC AC_INIT failed\n"); |
| return -EBUSY; |
| } |
| val = reg_poll(bp, CFC_REG_CAM_INIT_DONE, 1, 100, 10); |
| if (val != 1) { |
| BNX2X_ERR("CFC CAM_INIT failed\n"); |
| return -EBUSY; |
| } |
| REG_WR(bp, CFC_REG_DEBUG0, 0); |
| |
| /* read NIG statistic |
| to see if this is our first up since powerup */ |
| bnx2x_read_dmae(bp, NIG_REG_STAT2_BRB_OCTET, 2); |
| val = *bnx2x_sp(bp, wb_data[0]); |
| |
| /* do internal memory self test */ |
| if ((CHIP_IS_E1(bp)) && (val == 0) && bnx2x_int_mem_test(bp)) { |
| BNX2X_ERR("internal mem self test failed\n"); |
| return -EBUSY; |
| } |
| |
| bp->port.need_hw_lock = bnx2x_hw_lock_required(bp, |
| bp->common.shmem_base, |
| bp->common.shmem2_base); |
| |
| bnx2x_setup_fan_failure_detection(bp); |
| |
| /* clear PXP2 attentions */ |
| REG_RD(bp, PXP2_REG_PXP2_INT_STS_CLR_0); |
| |
| enable_blocks_attention(bp); |
| if (CHIP_PARITY_SUPPORTED(bp)) |
| enable_blocks_parity(bp); |
| |
| if (!BP_NOMCP(bp)) { |
| bnx2x_acquire_phy_lock(bp); |
| bnx2x_common_init_phy(bp, bp->common.shmem_base, |
| bp->common.shmem2_base); |
| bnx2x_release_phy_lock(bp); |
| } else |
| BNX2X_ERR("Bootcode is missing - can not initialize link\n"); |
| |
| return 0; |
| } |
| |
| static int bnx2x_init_port(struct bnx2x *bp) |
| { |
| int port = BP_PORT(bp); |
| int init_stage = port ? PORT1_STAGE : PORT0_STAGE; |
| u32 low, high; |
| u32 val; |
| |
| DP(BNX2X_MSG_MCP, "starting port init port %d\n", port); |
| |
| REG_WR(bp, NIG_REG_MASK_INTERRUPT_PORT0 + port*4, 0); |
| |
| bnx2x_init_block(bp, PXP_BLOCK, init_stage); |
| bnx2x_init_block(bp, PXP2_BLOCK, init_stage); |
| |
| bnx2x_init_block(bp, TCM_BLOCK, init_stage); |
| bnx2x_init_block(bp, UCM_BLOCK, init_stage); |
| bnx2x_init_block(bp, CCM_BLOCK, init_stage); |
| bnx2x_init_block(bp, XCM_BLOCK, init_stage); |
| |
| #ifdef BCM_CNIC |
| REG_WR(bp, QM_REG_CONNNUM_0 + port*4, 1024/16 - 1); |
| |
| bnx2x_init_block(bp, TIMERS_BLOCK, init_stage); |
| REG_WR(bp, TM_REG_LIN0_SCAN_TIME + port*4, 20); |
| REG_WR(bp, TM_REG_LIN0_MAX_ACTIVE_CID + port*4, 31); |
| #endif |
| |
| bnx2x_init_block(bp, DQ_BLOCK, init_stage); |
| |
| bnx2x_init_block(bp, BRB1_BLOCK, init_stage); |
| if (CHIP_REV_IS_SLOW(bp) && !CHIP_IS_E1H(bp)) { |
| /* no pause for emulation and FPGA */ |
| low = 0; |
| high = 513; |
| } else { |
| if (IS_E1HMF(bp)) |
| low = ((bp->flags & ONE_PORT_FLAG) ? 160 : 246); |
| else if (bp->dev->mtu > 4096) { |
| if (bp->flags & ONE_PORT_FLAG) |
| low = 160; |
| else { |
| val = bp->dev->mtu; |
| /* (24*1024 + val*4)/256 */ |
| low = 96 + (val/64) + ((val % 64) ? 1 : 0); |
| } |
| } else |
| low = ((bp->flags & ONE_PORT_FLAG) ? 80 : 160); |
| high = low + 56; /* 14*1024/256 */ |
| } |
| REG_WR(bp, BRB1_REG_PAUSE_LOW_THRESHOLD_0 + port*4, low); |
| REG_WR(bp, BRB1_REG_PAUSE_HIGH_THRESHOLD_0 + port*4, high); |
| |
| |
| bnx2x_init_block(bp, PRS_BLOCK, init_stage); |
| |
| bnx2x_init_block(bp, TSDM_BLOCK, init_stage); |
| bnx2x_init_block(bp, CSDM_BLOCK, init_stage); |
| bnx2x_init_block(bp, USDM_BLOCK, init_stage); |
| bnx2x_init_block(bp, XSDM_BLOCK, init_stage); |
| |
| bnx2x_init_block(bp, TSEM_BLOCK, init_stage); |
| bnx2x_init_block(bp, USEM_BLOCK, init_stage); |
| bnx2x_init_block(bp, CSEM_BLOCK, init_stage); |
| bnx2x_init_block(bp, XSEM_BLOCK, init_stage); |
| |
| bnx2x_init_block(bp, UPB_BLOCK, init_stage); |
| bnx2x_init_block(bp, XPB_BLOCK, init_stage); |
| |
| bnx2x_init_block(bp, PBF_BLOCK, init_stage); |
| |
| /* configure PBF to work without PAUSE mtu 9000 */ |
| REG_WR(bp, PBF_REG_P0_PAUSE_ENABLE + port*4, 0); |
| |
| /* update threshold */ |
| REG_WR(bp, PBF_REG_P0_ARB_THRSH + port*4, (9040/16)); |
| /* update init credit */ |
| REG_WR(bp, PBF_REG_P0_INIT_CRD + port*4, (9040/16) + 553 - 22); |
| |
| /* probe changes */ |
| REG_WR(bp, PBF_REG_INIT_P0 + port*4, 1); |
| msleep(5); |
| REG_WR(bp, PBF_REG_INIT_P0 + port*4, 0); |
| |
| #ifdef BCM_CNIC |
| bnx2x_init_block(bp, SRCH_BLOCK, init_stage); |
| #endif |
| bnx2x_init_block(bp, CDU_BLOCK, init_stage); |
| bnx2x_init_block(bp, CFC_BLOCK, init_stage); |
| |
| if (CHIP_IS_E1(bp)) { |
| REG_WR(bp, HC_REG_LEADING_EDGE_0 + port*8, 0); |
| REG_WR(bp, HC_REG_TRAILING_EDGE_0 + port*8, 0); |
| } |
| bnx2x_init_block(bp, HC_BLOCK, init_stage); |
| |
| bnx2x_init_block(bp, MISC_AEU_BLOCK, init_stage); |
| /* init aeu_mask_attn_func_0/1: |
| * - SF mode: bits 3-7 are masked. only bits 0-2 are in use |
| * - MF mode: bit 3 is masked. bits 0-2 are in use as in SF |
| * bits 4-7 are used for "per vn group attention" */ |
| REG_WR(bp, MISC_REG_AEU_MASK_ATTN_FUNC_0 + port*4, |
| (IS_E1HMF(bp) ? 0xF7 : 0x7)); |
| |
| bnx2x_init_block(bp, PXPCS_BLOCK, init_stage); |
| bnx2x_init_block(bp, EMAC0_BLOCK, init_stage); |
| bnx2x_init_block(bp, EMAC1_BLOCK, init_stage); |
| bnx2x_init_block(bp, DBU_BLOCK, init_stage); |
| bnx2x_init_block(bp, DBG_BLOCK, init_stage); |
| |
| bnx2x_init_block(bp, NIG_BLOCK, init_stage); |
| |
| REG_WR(bp, NIG_REG_XGXS_SERDES0_MODE_SEL + port*4, 1); |
| |
| if (CHIP_IS_E1H(bp)) { |
| /* 0x2 disable e1hov, 0x1 enable */ |
| REG_WR(bp, NIG_REG_LLH0_BRB1_DRV_MASK_MF + port*4, |
| (IS_E1HMF(bp) ? 0x1 : 0x2)); |
| |
| { |
| REG_WR(bp, NIG_REG_LLFC_ENABLE_0 + port*4, 0); |
| REG_WR(bp, NIG_REG_LLFC_OUT_EN_0 + port*4, 0); |
| REG_WR(bp, NIG_REG_PAUSE_ENABLE_0 + port*4, 1); |
| } |
| } |
| |
| bnx2x_init_block(bp, MCP_BLOCK, init_stage); |
| bnx2x_init_block(bp, DMAE_BLOCK, init_stage); |
| bp->port.need_hw_lock = bnx2x_hw_lock_required(bp, |
| bp->common.shmem_base, |
| bp->common.shmem2_base); |
| if (bnx2x_fan_failure_det_req(bp, bp->common.shmem_base, |
| bp->common.shmem2_base, port)) { |
| u32 reg_addr = (port ? MISC_REG_AEU_ENABLE1_FUNC_1_OUT_0 : |
| MISC_REG_AEU_ENABLE1_FUNC_0_OUT_0); |
| val = REG_RD(bp, reg_addr); |
| val |= AEU_INPUTS_ATTN_BITS_SPIO5; |
| REG_WR(bp, reg_addr, val); |
| } |
| bnx2x__link_reset(bp); |
| |
| return 0; |
| } |
| |
| #define ILT_PER_FUNC (768/2) |
| #define FUNC_ILT_BASE(func) (func * ILT_PER_FUNC) |
| /* the phys address is shifted right 12 bits and has an added |
| 1=valid bit added to the 53rd bit |
| then since this is a wide register(TM) |
| we split it into two 32 bit writes |
| */ |
| #define ONCHIP_ADDR1(x) ((u32)(((u64)x >> 12) & 0xFFFFFFFF)) |
| #define ONCHIP_ADDR2(x) ((u32)((1 << 20) | ((u64)x >> 44))) |
| #define PXP_ONE_ILT(x) (((x) << 10) | x) |
| #define PXP_ILT_RANGE(f, l) (((l) << 10) | f) |
| |
| #ifdef BCM_CNIC |
| #define CNIC_ILT_LINES 127 |
| #define CNIC_CTX_PER_ILT 16 |
| #else |
| #define CNIC_ILT_LINES 0 |
| #endif |
| |
| static void bnx2x_ilt_wr(struct bnx2x *bp, u32 index, dma_addr_t addr) |
| { |
| int reg; |
| |
| if (CHIP_IS_E1H(bp)) |
| reg = PXP2_REG_RQ_ONCHIP_AT_B0 + index*8; |
| else /* E1 */ |
| reg = PXP2_REG_RQ_ONCHIP_AT + index*8; |
| |
| bnx2x_wb_wr(bp, reg, ONCHIP_ADDR1(addr), ONCHIP_ADDR2(addr)); |
| } |
| |
| static int bnx2x_init_func(struct bnx2x *bp) |
| { |
| int port = BP_PORT(bp); |
| int func = BP_FUNC(bp); |
| u32 addr, val; |
| int i; |
| |
| DP(BNX2X_MSG_MCP, "starting func init func %d\n", func); |
| |
| /* set MSI reconfigure capability */ |
| addr = (port ? HC_REG_CONFIG_1 : HC_REG_CONFIG_0); |
| val = REG_RD(bp, addr); |
| val |= HC_CONFIG_0_REG_MSI_ATTN_EN_0; |
| REG_WR(bp, addr, val); |
| |
| i = FUNC_ILT_BASE(func); |
| |
| bnx2x_ilt_wr(bp, i, bnx2x_sp_mapping(bp, context)); |
| if (CHIP_IS_E1H(bp)) { |
| REG_WR(bp, PXP2_REG_RQ_CDU_FIRST_ILT, i); |
| REG_WR(bp, PXP2_REG_RQ_CDU_LAST_ILT, i + CNIC_ILT_LINES); |
| } else /* E1 */ |
| REG_WR(bp, PXP2_REG_PSWRQ_CDU0_L2P + func*4, |
| PXP_ILT_RANGE(i, i + CNIC_ILT_LINES)); |
| |
| #ifdef BCM_CNIC |
| i += 1 + CNIC_ILT_LINES; |
| bnx2x_ilt_wr(bp, i, bp->timers_mapping); |
| if (CHIP_IS_E1(bp)) |
| REG_WR(bp, PXP2_REG_PSWRQ_TM0_L2P + func*4, PXP_ONE_ILT(i)); |
| else { |
| REG_WR(bp, PXP2_REG_RQ_TM_FIRST_ILT, i); |
| REG_WR(bp, PXP2_REG_RQ_TM_LAST_ILT, i); |
| } |
| |
| i++; |
| bnx2x_ilt_wr(bp, i, bp->qm_mapping); |
| if (CHIP_IS_E1(bp)) |
| REG_WR(bp, PXP2_REG_PSWRQ_QM0_L2P + func*4, PXP_ONE_ILT(i)); |
| else { |
| REG_WR(bp, PXP2_REG_RQ_QM_FIRST_ILT, i); |
| REG_WR(bp, PXP2_REG_RQ_QM_LAST_ILT, i); |
| } |
| |
| i++; |
| bnx2x_ilt_wr(bp, i, bp->t1_mapping); |
| if (CHIP_IS_E1(bp)) |
| REG_WR(bp, PXP2_REG_PSWRQ_SRC0_L2P + func*4, PXP_ONE_ILT(i)); |
| else { |
| REG_WR(bp, PXP2_REG_RQ_SRC_FIRST_ILT, i); |
| REG_WR(bp, PXP2_REG_RQ_SRC_LAST_ILT, i); |
| } |
| |
| /* tell the searcher where the T2 table is */ |
| REG_WR(bp, SRC_REG_COUNTFREE0 + port*4, 16*1024/64); |
| |
| bnx2x_wb_wr(bp, SRC_REG_FIRSTFREE0 + port*16, |
| U64_LO(bp->t2_mapping), U64_HI(bp->t2_mapping)); |
| |
| bnx2x_wb_wr(bp, SRC_REG_LASTFREE0 + port*16, |
| U64_LO((u64)bp->t2_mapping + 16*1024 - 64), |
| U64_HI((u64)bp->t2_mapping + 16*1024 - 64)); |
| |
| REG_WR(bp, SRC_REG_NUMBER_HASH_BITS0 + port*4, 10); |
| #endif |
| |
| if (CHIP_IS_E1H(bp)) { |
| bnx2x_init_block(bp, MISC_BLOCK, FUNC0_STAGE + func); |
| bnx2x_init_block(bp, TCM_BLOCK, FUNC0_STAGE + func); |
| bnx2x_init_block(bp, UCM_BLOCK, FUNC0_STAGE + func); |
| bnx2x_init_block(bp, CCM_BLOCK, FUNC0_STAGE + func); |
| bnx2x_init_block(bp, XCM_BLOCK, FUNC0_STAGE + func); |
| bnx2x_init_block(bp, TSEM_BLOCK, FUNC0_STAGE + func); |
| bnx2x_init_block(bp, USEM_BLOCK, FUNC0_STAGE + func); |
| bnx2x_init_block(bp, CSEM_BLOCK, FUNC0_STAGE + func); |
| bnx2x_init_block(bp, XSEM_BLOCK, FUNC0_STAGE + func); |
| |
| REG_WR(bp, NIG_REG_LLH0_FUNC_EN + port*8, 1); |
| REG_WR(bp, NIG_REG_LLH0_FUNC_VLAN_ID + port*8, bp->e1hov); |
| } |
| |
| /* HC init per function */ |
| if (CHIP_IS_E1H(bp)) { |
| REG_WR(bp, MISC_REG_AEU_GENERAL_ATTN_12 + func*4, 0); |
| |
| REG_WR(bp, HC_REG_LEADING_EDGE_0 + port*8, 0); |
| REG_WR(bp, HC_REG_TRAILING_EDGE_0 + port*8, 0); |
| } |
| bnx2x_init_block(bp, HC_BLOCK, FUNC0_STAGE + func); |
| |
| /* Reset PCIE errors for debug */ |
| REG_WR(bp, 0x2114, 0xffffffff); |
| REG_WR(bp, 0x2120, 0xffffffff); |
| bnx2x_phy_probe(&bp->link_params); |
| return 0; |
| } |
| |
| int bnx2x_init_hw(struct bnx2x *bp, u32 load_code) |
| { |
| int i, rc = 0; |
| |
| DP(BNX2X_MSG_MCP, "function %d load_code %x\n", |
| BP_FUNC(bp), load_code); |
| |
| bp->dmae_ready = 0; |
| mutex_init(&bp->dmae_mutex); |
| rc = bnx2x_gunzip_init(bp); |
| if (rc) |
| return rc; |
| |
| switch (load_code) { |
| case FW_MSG_CODE_DRV_LOAD_COMMON: |
| rc = bnx2x_init_common(bp); |
| if (rc) |
| goto init_hw_err; |
| /* no break */ |
| |
| case FW_MSG_CODE_DRV_LOAD_PORT: |
| bp->dmae_ready = 1; |
| rc = bnx2x_init_port(bp); |
| if (rc) |
| goto init_hw_err; |
| /* no break */ |
| |
| case FW_MSG_CODE_DRV_LOAD_FUNCTION: |
| bp->dmae_ready = 1; |
| rc = bnx2x_init_func(bp); |
| if (rc) |
| goto init_hw_err; |
| break; |
| |
| default: |
| BNX2X_ERR("Unknown load_code (0x%x) from MCP\n", load_code); |
| break; |
| } |
| |
| if (!BP_NOMCP(bp)) { |
| int func = BP_FUNC(bp); |
| |
| bp->fw_drv_pulse_wr_seq = |
| (SHMEM_RD(bp, func_mb[func].drv_pulse_mb) & |
| DRV_PULSE_SEQ_MASK); |
| DP(BNX2X_MSG_MCP, "drv_pulse 0x%x\n", bp->fw_drv_pulse_wr_seq); |
| } |
| |
| /* this needs to be done before gunzip end */ |
| bnx2x_zero_def_sb(bp); |
| for_each_queue(bp, i) |
| bnx2x_zero_sb(bp, BP_L_ID(bp) + i); |
| #ifdef BCM_CNIC |
| bnx2x_zero_sb(bp, BP_L_ID(bp) + i); |
| #endif |
| |
| init_hw_err: |
| bnx2x_gunzip_end(bp); |
| |
| return rc; |
| } |
| |
| void bnx2x_free_mem(struct bnx2x *bp) |
| { |
| |
| #define BNX2X_PCI_FREE(x, y, size) \ |
| do { \ |
| if (x) { \ |
| dma_free_coherent(&bp->pdev->dev, size, x, y); \ |
| x = NULL; \ |
| y = 0; \ |
| } \ |
| } while (0) |
| |
| #define BNX2X_FREE(x) \ |
| do { \ |
| if (x) { \ |
| vfree(x); \ |
| x = NULL; \ |
| } \ |
| } while (0) |
| |
| int i; |
| |
| /* fastpath */ |
| /* Common */ |
| for_each_queue(bp, i) { |
| |
| /* status blocks */ |
| BNX2X_PCI_FREE(bnx2x_fp(bp, i, status_blk), |
| bnx2x_fp(bp, i, status_blk_mapping), |
| sizeof(struct host_status_block)); |
| } |
| /* Rx */ |
| for_each_queue(bp, i) { |
| |
| /* fastpath rx rings: rx_buf rx_desc rx_comp */ |
| BNX2X_FREE(bnx2x_fp(bp, i, rx_buf_ring)); |
| BNX2X_PCI_FREE(bnx2x_fp(bp, i, rx_desc_ring), |
| bnx2x_fp(bp, i, rx_desc_mapping), |
| sizeof(struct eth_rx_bd) * NUM_RX_BD); |
| |
| BNX2X_PCI_FREE(bnx2x_fp(bp, i, rx_comp_ring), |
| bnx2x_fp(bp, i, rx_comp_mapping), |
| sizeof(struct eth_fast_path_rx_cqe) * |
| NUM_RCQ_BD); |
| |
| /* SGE ring */ |
| BNX2X_FREE(bnx2x_fp(bp, i, rx_page_ring)); |
| BNX2X_PCI_FREE(bnx2x_fp(bp, i, rx_sge_ring), |
| bnx2x_fp(bp, i, rx_sge_mapping), |
| BCM_PAGE_SIZE * NUM_RX_SGE_PAGES); |
| } |
| /* Tx */ |
| for_each_queue(bp, i) { |
| |
| /* fastpath tx rings: tx_buf tx_desc */ |
| BNX2X_FREE(bnx2x_fp(bp, i, tx_buf_ring)); |
| BNX2X_PCI_FREE(bnx2x_fp(bp, i, tx_desc_ring), |
| bnx2x_fp(bp, i, tx_desc_mapping), |
| sizeof(union eth_tx_bd_types) * NUM_TX_BD); |
| } |
| /* end of fastpath */ |
| |
| BNX2X_PCI_FREE(bp->def_status_blk, bp->def_status_blk_mapping, |
| sizeof(struct host_def_status_block)); |
| |
| BNX2X_PCI_FREE(bp->slowpath, bp->slowpath_mapping, |
| sizeof(struct bnx2x_slowpath)); |
| |
| #ifdef BCM_CNIC |
| BNX2X_PCI_FREE(bp->t1, bp->t1_mapping, 64*1024); |
| BNX2X_PCI_FREE(bp->t2, bp->t2_mapping, 16*1024); |
| BNX2X_PCI_FREE(bp->timers, bp->timers_mapping, 8*1024); |
| BNX2X_PCI_FREE(bp->qm, bp->qm_mapping, 128*1024); |
| BNX2X_PCI_FREE(bp->cnic_sb, bp->cnic_sb_mapping, |
| sizeof(struct host_status_block)); |
| #endif |
| BNX2X_PCI_FREE(bp->spq, bp->spq_mapping, BCM_PAGE_SIZE); |
| |
| #undef BNX2X_PCI_FREE |
| #undef BNX2X_KFREE |
| } |
| |
| int bnx2x_alloc_mem(struct bnx2x *bp) |
| { |
| |
| #define BNX2X_PCI_ALLOC(x, y, size) \ |
| do { \ |
| x = dma_alloc_coherent(&bp->pdev->dev, size, y, GFP_KERNEL); \ |
| if (x == NULL) \ |
| goto alloc_mem_err; \ |
| memset(x, 0, size); \ |
| } while (0) |
| |
| #define BNX2X_ALLOC(x, size) \ |
| do { \ |
| x = vmalloc(size); \ |
| if (x == NULL) \ |
| goto alloc_mem_err; \ |
| memset(x, 0, size); \ |
| } while (0) |
| |
| int i; |
| |
| /* fastpath */ |
| /* Common */ |
| for_each_queue(bp, i) { |
| bnx2x_fp(bp, i, bp) = bp; |
| |
| /* status blocks */ |
| BNX2X_PCI_ALLOC(bnx2x_fp(bp, i, status_blk), |
| &bnx2x_fp(bp, i, status_blk_mapping), |
| sizeof(struct host_status_block)); |
| } |
| /* Rx */ |
| for_each_queue(bp, i) { |
| |
| /* fastpath rx rings: rx_buf rx_desc rx_comp */ |
| BNX2X_ALLOC(bnx2x_fp(bp, i, rx_buf_ring), |
| sizeof(struct sw_rx_bd) * NUM_RX_BD); |
| BNX2X_PCI_ALLOC(bnx2x_fp(bp, i, rx_desc_ring), |
| &bnx2x_fp(bp, i, rx_desc_mapping), |
| sizeof(struct eth_rx_bd) * NUM_RX_BD); |
| |
| BNX2X_PCI_ALLOC(bnx2x_fp(bp, i, rx_comp_ring), |
| &bnx2x_fp(bp, i, rx_comp_mapping), |
| sizeof(struct eth_fast_path_rx_cqe) * |
| NUM_RCQ_BD); |
| |
| /* SGE ring */ |
| BNX2X_ALLOC(bnx2x_fp(bp, i, rx_page_ring), |
| sizeof(struct sw_rx_page) * NUM_RX_SGE); |
| BNX2X_PCI_ALLOC(bnx2x_fp(bp, i, rx_sge_ring), |
| &bnx2x_fp(bp, i, rx_sge_mapping), |
| BCM_PAGE_SIZE * NUM_RX_SGE_PAGES); |
| } |
| /* Tx */ |
| for_each_queue(bp, i) { |
| |
| /* fastpath tx rings: tx_buf tx_desc */ |
| BNX2X_ALLOC(bnx2x_fp(bp, i, tx_buf_ring), |
| sizeof(struct sw_tx_bd) * NUM_TX_BD); |
| BNX2X_PCI_ALLOC(bnx2x_fp(bp, i, tx_desc_ring), |
| &bnx2x_fp(bp, i, tx_desc_mapping), |
| sizeof(union eth_tx_bd_types) * NUM_TX_BD); |
| } |
| /* end of fastpath */ |
| |
| BNX2X_PCI_ALLOC(bp->def_status_blk, &bp->def_status_blk_mapping, |
| sizeof(struct host_def_status_block)); |
| |
| BNX2X_PCI_ALLOC(bp->slowpath, &bp->slowpath_mapping, |
| sizeof(struct bnx2x_slowpath)); |
| |
| #ifdef BCM_CNIC |
| BNX2X_PCI_ALLOC(bp->t1, &bp->t1_mapping, 64*1024); |
| |
| /* allocate searcher T2 table |
| we allocate 1/4 of alloc num for T2 |
| (which is not entered into the ILT) */ |
| BNX2X_PCI_ALLOC(bp->t2, &bp->t2_mapping, 16*1024); |
| |
| /* Initialize T2 (for 1024 connections) */ |
| for (i = 0; i < 16*1024; i += 64) |
| *(u64 *)((char *)bp->t2 + i + 56) = bp->t2_mapping + i + 64; |
| |
| /* Timer block array (8*MAX_CONN) phys uncached for now 1024 conns */ |
| BNX2X_PCI_ALLOC(bp->timers, &bp->timers_mapping, 8*1024); |
| |
| /* QM queues (128*MAX_CONN) */ |
| BNX2X_PCI_ALLOC(bp->qm, &bp->qm_mapping, 128*1024); |
| |
| BNX2X_PCI_ALLOC(bp->cnic_sb, &bp->cnic_sb_mapping, |
| sizeof(struct host_status_block)); |
| #endif |
| |
| /* Slow path ring */ |
| BNX2X_PCI_ALLOC(bp->spq, &bp->spq_mapping, BCM_PAGE_SIZE); |
| |
| return 0; |
| |
| alloc_mem_err: |
| bnx2x_free_mem(bp); |
| return -ENOMEM; |
| |
| #undef BNX2X_PCI_ALLOC |
| #undef BNX2X_ALLOC |
| } |
| |
| |
| /* |
| * Init service functions |
| */ |
| |
| /** |
| * Sets a MAC in a CAM for a few L2 Clients for E1 chip |
| * |
| * @param bp driver descriptor |
| * @param set set or clear an entry (1 or 0) |
| * @param mac pointer to a buffer containing a MAC |
| * @param cl_bit_vec bit vector of clients to register a MAC for |
| * @param cam_offset offset in a CAM to use |
| * @param with_bcast set broadcast MAC as well |
| */ |
| static void bnx2x_set_mac_addr_e1_gen(struct bnx2x *bp, int set, u8 *mac, |
| u32 cl_bit_vec, u8 cam_offset, |
| u8 with_bcast) |
| { |
| struct mac_configuration_cmd *config = bnx2x_sp(bp, mac_config); |
| int port = BP_PORT(bp); |
| |
| /* CAM allocation |
| * unicasts 0-31:port0 32-63:port1 |
| * multicast 64-127:port0 128-191:port1 |
| */ |
| config->hdr.length = 1 + (with_bcast ? 1 : 0); |
| config->hdr.offset = cam_offset; |
| config->hdr.client_id = 0xff; |
| config->hdr.reserved1 = 0; |
| |
| /* primary MAC */ |
| config->config_table[0].cam_entry.msb_mac_addr = |
| swab16(*(u16 *)&mac[0]); |
| config->config_table[0].cam_entry.middle_mac_addr = |
| swab16(*(u16 *)&mac[2]); |
| config->config_table[0].cam_entry.lsb_mac_addr = |
| swab16(*(u16 *)&mac[4]); |
| config->config_table[0].cam_entry.flags = cpu_to_le16(port); |
| if (set) |
| config->config_table[0].target_table_entry.flags = 0; |
| else |
| CAM_INVALIDATE(config->config_table[0]); |
| config->config_table[0].target_table_entry.clients_bit_vector = |
| cpu_to_le32(cl_bit_vec); |
| config->config_table[0].target_table_entry.vlan_id = 0; |
| |
| DP(NETIF_MSG_IFUP, "%s MAC (%04x:%04x:%04x)\n", |
| (set ? "setting" : "clearing"), |
| config->config_table[0].cam_entry.msb_mac_addr, |
| config->config_table[0].cam_entry.middle_mac_addr, |
| config->config_table[0].cam_entry.lsb_mac_addr); |
| |
| /* broadcast */ |
| if (with_bcast) { |
| config->config_table[1].cam_entry.msb_mac_addr = |
| cpu_to_le16(0xffff); |
| config->config_table[1].cam_entry.middle_mac_addr = |
| cpu_to_le16(0xffff); |
| config->config_table[1].cam_entry.lsb_mac_addr = |
| cpu_to_le16(0xffff); |
| config->config_table[1].cam_entry.flags = cpu_to_le16(port); |
| if (set) |
| config->config_table[1].target_table_entry.flags = |
| TSTORM_CAM_TARGET_TABLE_ENTRY_BROADCAST; |
| else |
| CAM_INVALIDATE(config->config_table[1]); |
| config->config_table[1].target_table_entry.clients_bit_vector = |
| cpu_to_le32(cl_bit_vec); |
| config->config_table[1].target_table_entry.vlan_id = 0; |
| } |
| |
| bnx2x_sp_post(bp, RAMROD_CMD_ID_ETH_SET_MAC, 0, |
| U64_HI(bnx2x_sp_mapping(bp, mac_config)), |
| U64_LO(bnx2x_sp_mapping(bp, mac_config)), 0); |
| } |
| |
| /** |
| * Sets a MAC in a CAM for a few L2 Clients for E1H chip |
| * |
| * @param bp driver descriptor |
| * @param set set or clear an entry (1 or 0) |
| * @param mac pointer to a buffer containing a MAC |
| * @param cl_bit_vec bit vector of clients to register a MAC for |
| * @param cam_offset offset in a CAM to use |
| */ |
| static void bnx2x_set_mac_addr_e1h_gen(struct bnx2x *bp, int set, u8 *mac, |
| u32 cl_bit_vec, u8 cam_offset) |
| { |
| struct mac_configuration_cmd_e1h *config = |
| (struct mac_configuration_cmd_e1h *)bnx2x_sp(bp, mac_config); |
| |
| config->hdr.length = 1; |
| config->hdr.offset = cam_offset; |
| config->hdr.client_id = 0xff; |
| config->hdr.reserved1 = 0; |
| |
| /* primary MAC */ |
| config->config_table[0].msb_mac_addr = |
| swab16(*(u16 *)&mac[0]); |
| config->config_table[0].middle_mac_addr = |
| swab16(*(u16 *)&mac[2]); |
| config->config_table[0].lsb_mac_addr = |
| swab16(*(u16 *)&mac[4]); |
| config->config_table[0].clients_bit_vector = |
| cpu_to_le32(cl_bit_vec); |
| config->config_table[0].vlan_id = 0; |
| config->config_table[0].e1hov_id = cpu_to_le16(bp->e1hov); |
| if (set) |
| config->config_table[0].flags = BP_PORT(bp); |
| else |
| config->config_table[0].flags = |
| MAC_CONFIGURATION_ENTRY_E1H_ACTION_TYPE; |
| |
| DP(NETIF_MSG_IFUP, "%s MAC (%04x:%04x:%04x) E1HOV %d CLID mask %d\n", |
| (set ? "setting" : "clearing"), |
| config->config_table[0].msb_mac_addr, |
| config->config_table[0].middle_mac_addr, |
| config->config_table[0].lsb_mac_addr, bp->e1hov, cl_bit_vec); |
| |
| bnx2x_sp_post(bp, RAMROD_CMD_ID_ETH_SET_MAC, 0, |
| U64_HI(bnx2x_sp_mapping(bp, mac_config)), |
| U64_LO(bnx2x_sp_mapping(bp, mac_config)), 0); |
| } |
| |
| static int bnx2x_wait_ramrod(struct bnx2x *bp, int state, int idx, |
| int *state_p, int poll) |
| { |
| /* can take a while if any port is running */ |
| int cnt = 5000; |
| |
| DP(NETIF_MSG_IFUP, "%s for state to become %x on IDX [%d]\n", |
| poll ? "polling" : "waiting", state, idx); |
| |
| might_sleep(); |
| while (cnt--) { |
| if (poll) { |
| bnx2x_rx_int(bp->fp, 10); |
| /* if index is different from 0 |
| * the reply for some commands will |
| * be on the non default queue |
| */ |
| if (idx) |
| bnx2x_rx_int(&bp->fp[idx], 10); |
| } |
| |
| mb(); /* state is changed by bnx2x_sp_event() */ |
| if (*state_p == state) { |
| #ifdef BNX2X_STOP_ON_ERROR |
| DP(NETIF_MSG_IFUP, "exit (cnt %d)\n", 5000 - cnt); |
| #endif |
| return 0; |
| } |
| |
| msleep(1); |
| |
| if (bp->panic) |
| return -EIO; |
| } |
| |
| /* timeout! */ |
| BNX2X_ERR("timeout %s for state %x on IDX [%d]\n", |
| poll ? "polling" : "waiting", state, idx); |
| #ifdef BNX2X_STOP_ON_ERROR |
| bnx2x_panic(); |
| #endif |
| |
| return -EBUSY; |
| } |
| |
| void bnx2x_set_eth_mac_addr_e1h(struct bnx2x *bp, int set) |
| { |
| bp->set_mac_pending++; |
| smp_wmb(); |
| |
| bnx2x_set_mac_addr_e1h_gen(bp, set, bp->dev->dev_addr, |
| (1 << bp->fp->cl_id), BP_FUNC(bp)); |
| |
| /* Wait for a completion */ |
| bnx2x_wait_ramrod(bp, 0, 0, &bp->set_mac_pending, set ? 0 : 1); |
| } |
| |
| void bnx2x_set_eth_mac_addr_e1(struct bnx2x *bp, int set) |
| { |
| bp->set_mac_pending++; |
| smp_wmb(); |
| |
| bnx2x_set_mac_addr_e1_gen(bp, set, bp->dev->dev_addr, |
| (1 << bp->fp->cl_id), (BP_PORT(bp) ? 32 : 0), |
| 1); |
| |
| /* Wait for a completion */ |
| bnx2x_wait_ramrod(bp, 0, 0, &bp->set_mac_pending, set ? 0 : 1); |
| } |
| |
| #ifdef BCM_CNIC |
| /** |
| * Set iSCSI MAC(s) at the next enties in the CAM after the ETH |
| * MAC(s). This function will wait until the ramdord completion |
| * returns. |
| * |
| * @param bp driver handle |
| * @param set set or clear the CAM entry |
| * |
| * @return 0 if cussess, -ENODEV if ramrod doesn't return. |
| */ |
| int bnx2x_set_iscsi_eth_mac_addr(struct bnx2x *bp, int set) |
| { |
| u32 cl_bit_vec = (1 << BCM_ISCSI_ETH_CL_ID); |
| |
| bp->set_mac_pending++; |
| smp_wmb(); |
| |
| /* Send a SET_MAC ramrod */ |
| if (CHIP_IS_E1(bp)) |
| bnx2x_set_mac_addr_e1_gen(bp, set, bp->iscsi_mac, |
| cl_bit_vec, (BP_PORT(bp) ? 32 : 0) + 2, |
| 1); |
| else |
| /* CAM allocation for E1H |
| * unicasts: by func number |
| * multicast: 20+FUNC*20, 20 each |
| */ |
| bnx2x_set_mac_addr_e1h_gen(bp, set, bp->iscsi_mac, |
| cl_bit_vec, E1H_FUNC_MAX + BP_FUNC(bp)); |
| |
| /* Wait for a completion when setting */ |
| bnx2x_wait_ramrod(bp, 0, 0, &bp->set_mac_pending, set ? 0 : 1); |
| |
| return 0; |
| } |
| #endif |
| |
| int bnx2x_setup_leading(struct bnx2x *bp) |
| { |
| int rc; |
| |
| /* reset IGU state */ |
| bnx2x_ack_sb(bp, bp->fp[0].sb_id, CSTORM_ID, 0, IGU_INT_ENABLE, 0); |
| |
| /* SETUP ramrod */ |
| bnx2x_sp_post(bp, RAMROD_CMD_ID_ETH_PORT_SETUP, 0, 0, 0, 0); |
| |
| /* Wait for completion */ |
| rc = bnx2x_wait_ramrod(bp, BNX2X_STATE_OPEN, 0, &(bp->state), 0); |
| |
| return rc; |
| } |
| |
| int bnx2x_setup_multi(struct bnx2x *bp, int index) |
| { |
| struct bnx2x_fastpath *fp = &bp->fp[index]; |
| |
| /* reset IGU state */ |
| bnx2x_ack_sb(bp, fp->sb_id, CSTORM_ID, 0, IGU_INT_ENABLE, 0); |
| |
| /* SETUP ramrod */ |
| fp->state = BNX2X_FP_STATE_OPENING; |
| bnx2x_sp_post(bp, RAMROD_CMD_ID_ETH_CLIENT_SETUP, index, 0, |
| fp->cl_id, 0); |
| |
| /* Wait for completion */ |
| return bnx2x_wait_ramrod(bp, BNX2X_FP_STATE_OPEN, index, |
| &(fp->state), 0); |
| } |
| |
| |
| void bnx2x_set_num_queues_msix(struct bnx2x *bp) |
| { |
| |
| switch (bp->multi_mode) { |
| case ETH_RSS_MODE_DISABLED: |
| bp->num_queues = 1; |
| break; |
| |
| case ETH_RSS_MODE_REGULAR: |
| if (num_queues) |
| bp->num_queues = min_t(u32, num_queues, |
| BNX2X_MAX_QUEUES(bp)); |
| else |
| bp->num_queues = min_t(u32, num_online_cpus(), |
| BNX2X_MAX_QUEUES(bp)); |
| break; |
| |
| |
| default: |
| bp->num_queues = 1; |
| break; |
| } |
| } |
| |
| |
| |
| static int bnx2x_stop_multi(struct bnx2x *bp, int index) |
| { |
| struct bnx2x_fastpath *fp = &bp->fp[index]; |
| int rc; |
| |
| /* halt the connection */ |
| fp->state = BNX2X_FP_STATE_HALTING; |
| bnx2x_sp_post(bp, RAMROD_CMD_ID_ETH_HALT, index, 0, fp->cl_id, 0); |
| |
| /* Wait for completion */ |
| rc = bnx2x_wait_ramrod(bp, BNX2X_FP_STATE_HALTED, index, |
| &(fp->state), 1); |
| if (rc) /* timeout */ |
| return rc; |
| |
| /* delete cfc entry */ |
| bnx2x_sp_post(bp, RAMROD_CMD_ID_ETH_CFC_DEL, index, 0, 0, 1); |
| |
| /* Wait for completion */ |
| rc = bnx2x_wait_ramrod(bp, BNX2X_FP_STATE_CLOSED, index, |
| &(fp->state), 1); |
| return rc; |
| } |
| |
| static int bnx2x_stop_leading(struct bnx2x *bp) |
| { |
| __le16 dsb_sp_prod_idx; |
| /* if the other port is handling traffic, |
| this can take a lot of time */ |
| int cnt = 500; |
| int rc; |
| |
| might_sleep(); |
| |
| /* Send HALT ramrod */ |
| bp->fp[0].state = BNX2X_FP_STATE_HALTING; |
| bnx2x_sp_post(bp, RAMROD_CMD_ID_ETH_HALT, 0, 0, bp->fp->cl_id, 0); |
| |
| /* Wait for completion */ |
| rc = bnx2x_wait_ramrod(bp, BNX2X_FP_STATE_HALTED, 0, |
| &(bp->fp[0].state), 1); |
| if (rc) /* timeout */ |
| return rc; |
| |
| dsb_sp_prod_idx = *bp->dsb_sp_prod; |
| |
| /* Send PORT_DELETE ramrod */ |
| bnx2x_sp_post(bp, RAMROD_CMD_ID_ETH_PORT_DEL, 0, 0, 0, 1); |
| |
| /* Wait for completion to arrive on default status block |
| we are going to reset the chip anyway |
| so there is not much to do if this times out |
| */ |
| while (dsb_sp_prod_idx == *bp->dsb_sp_prod) { |
| if (!cnt) { |
| DP(NETIF_MSG_IFDOWN, "timeout waiting for port del " |
| "dsb_sp_prod 0x%x != dsb_sp_prod_idx 0x%x\n", |
| *bp->dsb_sp_prod, dsb_sp_prod_idx); |
| #ifdef BNX2X_STOP_ON_ERROR |
| bnx2x_panic(); |
| #endif |
| rc = -EBUSY; |
| break; |
| } |
| cnt--; |
| msleep(1); |
| rmb(); /* Refresh the dsb_sp_prod */ |
| } |
| bp->state = BNX2X_STATE_CLOSING_WAIT4_UNLOAD; |
| bp->fp[0].state = BNX2X_FP_STATE_CLOSED; |
| |
| return rc; |
| } |
| |
| static void bnx2x_reset_func(struct bnx2x *bp) |
| { |
| int port = BP_PORT(bp); |
| int func = BP_FUNC(bp); |
| int base, i; |
| |
| /* Configure IGU */ |
| REG_WR(bp, HC_REG_LEADING_EDGE_0 + port*8, 0); |
| REG_WR(bp, HC_REG_TRAILING_EDGE_0 + port*8, 0); |
| |
| #ifdef BCM_CNIC |
| /* Disable Timer scan */ |
| REG_WR(bp, TM_REG_EN_LINEAR0_TIMER + port*4, 0); |
| /* |
| * Wait for at least 10ms and up to 2 second for the timers scan to |
| * complete |
| */ |
| for (i = 0; i < 200; i++) { |
| msleep(10); |
| if (!REG_RD(bp, TM_REG_LIN0_SCAN_ON + port*4)) |
| break; |
| } |
| #endif |
| /* Clear ILT */ |
| base = FUNC_ILT_BASE(func); |
| for (i = base; i < base + ILT_PER_FUNC; i++) |
| bnx2x_ilt_wr(bp, i, 0); |
| } |
| |
| static void bnx2x_reset_port(struct bnx2x *bp) |
| { |
| int port = BP_PORT(bp); |
| u32 val; |
| |
| REG_WR(bp, NIG_REG_MASK_INTERRUPT_PORT0 + port*4, 0); |
| |
| /* Do not rcv packets to BRB */ |
| REG_WR(bp, NIG_REG_LLH0_BRB1_DRV_MASK + port*4, 0x0); |
| /* Do not direct rcv packets that are not for MCP to the BRB */ |
| REG_WR(bp, (port ? NIG_REG_LLH1_BRB1_NOT_MCP : |
| NIG_REG_LLH0_BRB1_NOT_MCP), 0x0); |
| |
| /* Configure AEU */ |
| REG_WR(bp, MISC_REG_AEU_MASK_ATTN_FUNC_0 + port*4, 0); |
| |
| msleep(100); |
| /* Check for BRB port occupancy */ |
| val = REG_RD(bp, BRB1_REG_PORT_NUM_OCC_BLOCKS_0 + port*4); |
| if (val) |
| DP(NETIF_MSG_IFDOWN, |
| "BRB1 is not empty %d blocks are occupied\n", val); |
| |
| /* TODO: Close Doorbell port? */ |
| } |
| |
| static void bnx2x_reset_chip(struct bnx2x *bp, u32 reset_code) |
| { |
| DP(BNX2X_MSG_MCP, "function %d reset_code %x\n", |
| BP_FUNC(bp), reset_code); |
| |
| switch (reset_code) { |
| case FW_MSG_CODE_DRV_UNLOAD_COMMON: |
| bnx2x_reset_port(bp); |
| bnx2x_reset_func(bp); |
| bnx2x_reset_common(bp); |
| break; |
| |
| case FW_MSG_CODE_DRV_UNLOAD_PORT: |
| bnx2x_reset_port(bp); |
| bnx2x_reset_func(bp); |
| break; |
| |
| case FW_MSG_CODE_DRV_UNLOAD_FUNCTION: |
| bnx2x_reset_func(bp); |
| break; |
| |
| default: |
| BNX2X_ERR("Unknown reset_code (0x%x) from MCP\n", reset_code); |
| break; |
| } |
| } |
| |
| void bnx2x_chip_cleanup(struct bnx2x *bp, int unload_mode) |
| { |
| int port = BP_PORT(bp); |
| u32 reset_code = 0; |
| int i, cnt, rc; |
| |
| /* Wait until tx fastpath tasks complete */ |
| for_each_queue(bp, i) { |
| struct bnx2x_fastpath *fp = &bp->fp[i]; |
| |
| cnt = 1000; |
| while (bnx2x_has_tx_work_unload(fp)) { |
| |
| bnx2x_tx_int(fp); |
| if (!cnt) { |
| BNX2X_ERR("timeout waiting for queue[%d]\n", |
| i); |
| #ifdef BNX2X_STOP_ON_ERROR |
| bnx2x_panic(); |
| return -EBUSY; |
| #else |
| break; |
| #endif |
| } |
| cnt--; |
| msleep(1); |
| } |
| } |
| /* Give HW time to discard old tx messages */ |
| msleep(1); |
| |
| if (CHIP_IS_E1(bp)) { |
| struct mac_configuration_cmd *config = |
| bnx2x_sp(bp, mcast_config); |
| |
| bnx2x_set_eth_mac_addr_e1(bp, 0); |
| |
| for (i = 0; i < config->hdr.length; i++) |
| CAM_INVALIDATE(config->config_table[i]); |
| |
| config->hdr.length = i; |
| if (CHIP_REV_IS_SLOW(bp)) |
| config->hdr.offset = BNX2X_MAX_EMUL_MULTI*(1 + port); |
| else |
| config->hdr.offset = BNX2X_MAX_MULTICAST*(1 + port); |
| config->hdr.client_id = bp->fp->cl_id; |
| config->hdr.reserved1 = 0; |
| |
| bp->set_mac_pending++; |
| smp_wmb(); |
| |
| bnx2x_sp_post(bp, RAMROD_CMD_ID_ETH_SET_MAC, 0, |
| U64_HI(bnx2x_sp_mapping(bp, mcast_config)), |
| U64_LO(bnx2x_sp_mapping(bp, mcast_config)), 0); |
| |
| } else { /* E1H */ |
| REG_WR(bp, NIG_REG_LLH0_FUNC_EN + port*8, 0); |
| |
| bnx2x_set_eth_mac_addr_e1h(bp, 0); |
| |
| for (i = 0; i < MC_HASH_SIZE; i++) |
| REG_WR(bp, MC_HASH_OFFSET(bp, i), 0); |
| |
| REG_WR(bp, MISC_REG_E1HMF_MODE, 0); |
| } |
| #ifdef BCM_CNIC |
| /* Clear iSCSI L2 MAC */ |
| mutex_lock(&bp->cnic_mutex); |
| if (bp->cnic_flags & BNX2X_CNIC_FLAG_MAC_SET) { |
| bnx2x_set_iscsi_eth_mac_addr(bp, 0); |
| bp->cnic_flags &= ~BNX2X_CNIC_FLAG_MAC_SET; |
| } |
| mutex_unlock(&bp->cnic_mutex); |
| #endif |
| |
| if (unload_mode == UNLOAD_NORMAL) |
| reset_code = DRV_MSG_CODE_UNLOAD_REQ_WOL_DIS; |
| |
| else if (bp->flags & NO_WOL_FLAG) |
| reset_code = DRV_MSG_CODE_UNLOAD_REQ_WOL_MCP; |
| |
| else if (bp->wol) { |
| u32 emac_base = port ? GRCBASE_EMAC1 : GRCBASE_EMAC0; |
| u8 *mac_addr = bp->dev->dev_addr; |
| u32 val; |
| /* The mac address is written to entries 1-4 to |
| preserve entry 0 which is used by the PMF */ |
| u8 entry = (BP_E1HVN(bp) + 1)*8; |
| |
| val = (mac_addr[0] << 8) | mac_addr[1]; |
| EMAC_WR(bp, EMAC_REG_EMAC_MAC_MATCH + entry, val); |
| |
| val = (mac_addr[2] << 24) | (mac_addr[3] << 16) | |
| (mac_addr[4] << 8) | mac_addr[5]; |
| EMAC_WR(bp, EMAC_REG_EMAC_MAC_MATCH + entry + 4, val); |
| |
| reset_code = DRV_MSG_CODE_UNLOAD_REQ_WOL_EN; |
| |
| } else |
| reset_code = DRV_MSG_CODE_UNLOAD_REQ_WOL_DIS; |
| |
| /* Close multi and leading connections |
| Completions for ramrods are collected in a synchronous way */ |
| for_each_nondefault_queue(bp, i) |
| if (bnx2x_stop_multi(bp, i)) |
| goto unload_error; |
| |
| rc = bnx2x_stop_leading(bp); |
| if (rc) { |
| BNX2X_ERR("Stop leading failed!\n"); |
| #ifdef BNX2X_STOP_ON_ERROR |
| return -EBUSY; |
| #else |
| goto unload_error; |
| #endif |
| } |
| |
| unload_error: |
| if (!BP_NOMCP(bp)) |
| reset_code = bnx2x_fw_command(bp, reset_code, 0); |
| else { |
| DP(NETIF_MSG_IFDOWN, "NO MCP - load counts %d, %d, %d\n", |
| load_count[0], load_count[1], load_count[2]); |
| load_count[0]--; |
| load_count[1 + port]--; |
| DP(NETIF_MSG_IFDOWN, "NO MCP - new load counts %d, %d, %d\n", |
| load_count[0], load_count[1], load_count[2]); |
| if (load_count[0] == 0) |
| reset_code = FW_MSG_CODE_DRV_UNLOAD_COMMON; |
| else if (load_count[1 + port] == 0) |
| reset_code = FW_MSG_CODE_DRV_UNLOAD_PORT; |
| else |
| reset_code = FW_MSG_CODE_DRV_UNLOAD_FUNCTION; |
| } |
| |
| if ((reset_code == FW_MSG_CODE_DRV_UNLOAD_COMMON) || |
| (reset_code == FW_MSG_CODE_DRV_UNLOAD_PORT)) |
| bnx2x__link_reset(bp); |
| |
| /* Reset the chip */ |
| bnx2x_reset_chip(bp, reset_code); |
| |
| /* Report UNLOAD_DONE to MCP */ |
| if (!BP_NOMCP(bp)) |
| bnx2x_fw_command(bp, DRV_MSG_CODE_UNLOAD_DONE, 0); |
| |
| } |
| |
| void bnx2x_disable_close_the_gate(struct bnx2x *bp) |
| { |
| u32 val; |
| |
| DP(NETIF_MSG_HW, "Disabling \"close the gates\"\n"); |
| |
| if (CHIP_IS_E1(bp)) { |
| int port = BP_PORT(bp); |
| u32 addr = port ? MISC_REG_AEU_MASK_ATTN_FUNC_1 : |
| MISC_REG_AEU_MASK_ATTN_FUNC_0; |
| |
| val = REG_RD(bp, addr); |
| val &= ~(0x300); |
| REG_WR(bp, addr, val); |
| } else if (CHIP_IS_E1H(bp)) { |
| val = REG_RD(bp, MISC_REG_AEU_GENERAL_MASK); |
| val &= ~(MISC_AEU_GENERAL_MASK_REG_AEU_PXP_CLOSE_MASK | |
| MISC_AEU_GENERAL_MASK_REG_AEU_NIG_CLOSE_MASK); |
| REG_WR(bp, MISC_REG_AEU_GENERAL_MASK, val); |
| } |
| } |
| |
| |
| /* Close gates #2, #3 and #4: */ |
| static void bnx2x_set_234_gates(struct bnx2x *bp, bool close) |
| { |
| u32 val, addr; |
| |
| /* Gates #2 and #4a are closed/opened for "not E1" only */ |
| if (!CHIP_IS_E1(bp)) { |
| /* #4 */ |
| val = REG_RD(bp, PXP_REG_HST_DISCARD_DOORBELLS); |
| REG_WR(bp, PXP_REG_HST_DISCARD_DOORBELLS, |
| close ? (val | 0x1) : (val & (~(u32)1))); |
| /* #2 */ |
| val = REG_RD(bp, PXP_REG_HST_DISCARD_INTERNAL_WRITES); |
| REG_WR(bp, PXP_REG_HST_DISCARD_INTERNAL_WRITES, |
| close ? (val | 0x1) : (val & (~(u32)1))); |
| } |
| |
| /* #3 */ |
| addr = BP_PORT(bp) ? HC_REG_CONFIG_1 : HC_REG_CONFIG_0; |
| val = REG_RD(bp, addr); |
| REG_WR(bp, addr, (!close) ? (val | 0x1) : (val & (~(u32)1))); |
| |
| DP(NETIF_MSG_HW, "%s gates #2, #3 and #4\n", |
| close ? "closing" : "opening"); |
| mmiowb(); |
| } |
| |
| #define SHARED_MF_CLP_MAGIC 0x80000000 /* `magic' bit */ |
| |
| static void bnx2x_clp_reset_prep(struct bnx2x *bp, u32 *magic_val) |
| { |
| /* Do some magic... */ |
| u32 val = MF_CFG_RD(bp, shared_mf_config.clp_mb); |
| *magic_val = val & SHARED_MF_CLP_MAGIC; |
| MF_CFG_WR(bp, shared_mf_config.clp_mb, val | SHARED_MF_CLP_MAGIC); |
| } |
| |
| /* Restore the value of the `magic' bit. |
| * |
| * @param pdev Device handle. |
| * @param magic_val Old value of the `magic' bit. |
| */ |
| static void bnx2x_clp_reset_done(struct bnx2x *bp, u32 magic_val) |
| { |
| /* Restore the `magic' bit value... */ |
| /* u32 val = SHMEM_RD(bp, mf_cfg.shared_mf_config.clp_mb); |
| SHMEM_WR(bp, mf_cfg.shared_mf_config.clp_mb, |
| (val & (~SHARED_MF_CLP_MAGIC)) | magic_val); */ |
| u32 val = MF_CFG_RD(bp, shared_mf_config.clp_mb); |
| MF_CFG_WR(bp, shared_mf_config.clp_mb, |
| (val & (~SHARED_MF_CLP_MAGIC)) | magic_val); |
| } |
| |
| /* Prepares for MCP reset: takes care of CLP configurations. |
| * |
| * @param bp |
| * @param magic_val Old value of 'magic' bit. |
| */ |
| static void bnx2x_reset_mcp_prep(struct bnx2x *bp, u32 *magic_val) |
| { |
| u32 shmem; |
| u32 validity_offset; |
| |
| DP(NETIF_MSG_HW, "Starting\n"); |
| |
| /* Set `magic' bit in order to save MF config */ |
| if (!CHIP_IS_E1(bp)) |
| bnx2x_clp_reset_prep(bp, magic_val); |
| |
| /* Get shmem offset */ |
| shmem = REG_RD(bp, MISC_REG_SHARED_MEM_ADDR); |
| validity_offset = offsetof(struct shmem_region, validity_map[0]); |
| |
| /* Clear validity map flags */ |
| if (shmem > 0) |
| REG_WR(bp, shmem + validity_offset, 0); |
| } |
| |
| #define MCP_TIMEOUT 5000 /* 5 seconds (in ms) */ |
| #define MCP_ONE_TIMEOUT 100 /* 100 ms */ |
| |
| /* Waits for MCP_ONE_TIMEOUT or MCP_ONE_TIMEOUT*10, |
| * depending on the HW type. |
| * |
| * @param bp |
| */ |
| static inline void bnx2x_mcp_wait_one(struct bnx2x *bp) |
| { |
| /* special handling for emulation and FPGA, |
| wait 10 times longer */ |
| if (CHIP_REV_IS_SLOW(bp)) |
| msleep(MCP_ONE_TIMEOUT*10); |
| else |
| msleep(MCP_ONE_TIMEOUT); |
| } |
| |
| static int bnx2x_reset_mcp_comp(struct bnx2x *bp, u32 magic_val) |
| { |
| u32 shmem, cnt, validity_offset, val; |
| int rc = 0; |
| |
| msleep(100); |
| |
| /* Get shmem offset */ |
| shmem = REG_RD(bp, MISC_REG_SHARED_MEM_ADDR); |
| if (shmem == 0) { |
| BNX2X_ERR("Shmem 0 return failure\n"); |
| rc = -ENOTTY; |
| goto exit_lbl; |
| } |
| |
| validity_offset = offsetof(struct shmem_region, validity_map[0]); |
| |
| /* Wait for MCP to come up */ |
| for (cnt = 0; cnt < (MCP_TIMEOUT / MCP_ONE_TIMEOUT); cnt++) { |
| /* TBD: its best to check validity map of last port. |
| * currently checks on port 0. |
| */ |
| val = REG_RD(bp, shmem + validity_offset); |
| DP(NETIF_MSG_HW, "shmem 0x%x validity map(0x%x)=0x%x\n", shmem, |
| shmem + validity_offset, val); |
| |
| /* check that shared memory is valid. */ |
| if ((val & (SHR_MEM_VALIDITY_DEV_INFO | SHR_MEM_VALIDITY_MB)) |
| == (SHR_MEM_VALIDITY_DEV_INFO | SHR_MEM_VALIDITY_MB)) |
| break; |
| |
| bnx2x_mcp_wait_one(bp); |
| } |
| |
| DP(NETIF_MSG_HW, "Cnt=%d Shmem validity map 0x%x\n", cnt, val); |
| |
| /* Check that shared memory is valid. This indicates that MCP is up. */ |
| if ((val & (SHR_MEM_VALIDITY_DEV_INFO | SHR_MEM_VALIDITY_MB)) != |
| (SHR_MEM_VALIDITY_DEV_INFO | SHR_MEM_VALIDITY_MB)) { |
| BNX2X_ERR("Shmem signature not present. MCP is not up !!\n"); |
| rc = -ENOTTY; |
| goto exit_lbl; |
| } |
| |
| exit_lbl: |
| /* Restore the `magic' bit value */ |
| if (!CHIP_IS_E1(bp)) |
| bnx2x_clp_reset_done(bp, magic_val); |
| |
| return rc; |
| } |
| |
| static void bnx2x_pxp_prep(struct bnx2x *bp) |
| { |
| if (!CHIP_IS_E1(bp)) { |
| REG_WR(bp, PXP2_REG_RD_START_INIT, 0); |
| REG_WR(bp, PXP2_REG_RQ_RBC_DONE, 0); |
| REG_WR(bp, PXP2_REG_RQ_CFG_DONE, 0); |
| mmiowb(); |
| } |
| } |
| |
| /* |
| * Reset the whole chip except for: |
| * - PCIE core |
| * - PCI Glue, PSWHST, PXP/PXP2 RF (all controlled by |
| * one reset bit) |
| * - IGU |
| * - MISC (including AEU) |
| * - GRC |
| * - RBCN, RBCP |
| */ |
| static void bnx2x_process_kill_chip_reset(struct bnx2x *bp) |
| { |
| u32 not_reset_mask1, reset_mask1, not_reset_mask2, reset_mask2; |
| |
| not_reset_mask1 = |
| MISC_REGISTERS_RESET_REG_1_RST_HC | |
| MISC_REGISTERS_RESET_REG_1_RST_PXPV | |
| MISC_REGISTERS_RESET_REG_1_RST_PXP; |
| |
| not_reset_mask2 = |
| MISC_REGISTERS_RESET_REG_2_RST_MDIO | |
| MISC_REGISTERS_RESET_REG_2_RST_EMAC0_HARD_CORE | |
| MISC_REGISTERS_RESET_REG_2_RST_EMAC1_HARD_CORE | |
| MISC_REGISTERS_RESET_REG_2_RST_MISC_CORE | |
| MISC_REGISTERS_RESET_REG_2_RST_RBCN | |
| MISC_REGISTERS_RESET_REG_2_RST_GRC | |
| MISC_REGISTERS_RESET_REG_2_RST_MCP_N_RESET_REG_HARD_CORE | |
| MISC_REGISTERS_RESET_REG_2_RST_MCP_N_HARD_CORE_RST_B; |
| |
| reset_mask1 = 0xffffffff; |
| |
| if (CHIP_IS_E1(bp)) |
| reset_mask2 = 0xffff; |
| else |
| reset_mask2 = 0x1ffff; |
| |
| REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_1_CLEAR, |
| reset_mask1 & (~not_reset_mask1)); |
| REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR, |
| reset_mask2 & (~not_reset_mask2)); |
| |
| barrier(); |
| mmiowb(); |
| |
| REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_1_SET, reset_mask1); |
| REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_SET, reset_mask2); |
| mmiowb(); |
| } |
| |
| static int bnx2x_process_kill(struct bnx2x *bp) |
| { |
| int cnt = 1000; |
| u32 val = 0; |
| u32 sr_cnt, blk_cnt, port_is_idle_0, port_is_idle_1, pgl_exp_rom2; |
| |
| |
| /* Empty the Tetris buffer, wait for 1s */ |
| do { |
| sr_cnt = REG_RD(bp, PXP2_REG_RD_SR_CNT); |
| blk_cnt = REG_RD(bp, PXP2_REG_RD_BLK_CNT); |
| port_is_idle_0 = REG_RD(bp, PXP2_REG_RD_PORT_IS_IDLE_0); |
| port_is_idle_1 = REG_RD(bp, PXP2_REG_RD_PORT_IS_IDLE_1); |
| pgl_exp_rom2 = REG_RD(bp, PXP2_REG_PGL_EXP_ROM2); |
| if ((sr_cnt == 0x7e) && (blk_cnt == 0xa0) && |
| ((port_is_idle_0 & 0x1) == 0x1) && |
| ((port_is_idle_1 & 0x1) == 0x1) && |
| (pgl_exp_rom2 == 0xffffffff)) |
| break; |
| msleep(1); |
| } while (cnt-- > 0); |
| |
| if (cnt <= 0) { |
| DP(NETIF_MSG_HW, "Tetris buffer didn't get empty or there" |
| " are still" |
| " outstanding read requests after 1s!\n"); |
| DP(NETIF_MSG_HW, "sr_cnt=0x%08x, blk_cnt=0x%08x," |
| " port_is_idle_0=0x%08x," |
| " port_is_idle_1=0x%08x, pgl_exp_rom2=0x%08x\n", |
| sr_cnt, blk_cnt, port_is_idle_0, port_is_idle_1, |
| pgl_exp_rom2); |
| return -EAGAIN; |
| } |
| |
| barrier(); |
| |
| /* Close gates #2, #3 and #4 */ |
| bnx2x_set_234_gates(bp, true); |
| |
| /* TBD: Indicate that "process kill" is in progress to MCP */ |
| |
| /* Clear "unprepared" bit */ |
| REG_WR(bp, MISC_REG_UNPREPARED, 0); |
| barrier(); |
| |
| /* Make sure all is written to the chip before the reset */ |
| mmiowb(); |
| |
| /* Wait for 1ms to empty GLUE and PCI-E core queues, |
| * PSWHST, GRC and PSWRD Tetris buffer. |
| */ |
| msleep(1); |
| |
| /* Prepare to chip reset: */ |
| /* MCP */ |
| bnx2x_reset_mcp_prep(bp, &val); |
| |
| /* PXP */ |
| bnx2x_pxp_prep(bp); |
| barrier(); |
| |
| /* reset the chip */ |
| bnx2x_process_kill_chip_reset(bp); |
| barrier(); |
| |
| /* Recover after reset: */ |
| /* MCP */ |
| if (bnx2x_reset_mcp_comp(bp, val)) |
| return -EAGAIN; |
| |
| /* PXP */ |
| bnx2x_pxp_prep(bp); |
| |
| /* Open the gates #2, #3 and #4 */ |
| bnx2x_set_234_gates(bp, false); |
| |
| /* TBD: IGU/AEU preparation bring back the AEU/IGU to a |
| * reset state, re-enable attentions. */ |
| |
| return 0; |
| } |
| |
| static int bnx2x_leader_reset(struct bnx2x *bp) |
| { |
| int rc = 0; |
| /* Try to recover after the failure */ |
| if (bnx2x_process_kill(bp)) { |
| printk(KERN_ERR "%s: Something bad had happen! Aii!\n", |
| bp->dev->name); |
| rc = -EAGAIN; |
| goto exit_leader_reset; |
| } |
| |
| /* Clear "reset is in progress" bit and update the driver state */ |
| bnx2x_set_reset_done(bp); |
| bp->recovery_state = BNX2X_RECOVERY_DONE; |
| |
| exit_leader_reset: |
| bp->is_leader = 0; |
| bnx2x_release_hw_lock(bp, HW_LOCK_RESOURCE_RESERVED_08); |
| smp_wmb(); |
| return rc; |
| } |
| |
| /* Assumption: runs under rtnl lock. This together with the fact |
| * that it's called only from bnx2x_reset_task() ensure that it |
| * will never be called when netif_running(bp->dev) is false. |
| */ |
| static void bnx2x_parity_recover(struct bnx2x *bp) |
| { |
| DP(NETIF_MSG_HW, "Handling parity\n"); |
| while (1) { |
| switch (bp->recovery_state) { |
| case BNX2X_RECOVERY_INIT: |
| DP(NETIF_MSG_HW, "State is BNX2X_RECOVERY_INIT\n"); |
| /* Try to get a LEADER_LOCK HW lock */ |
| if (bnx2x_trylock_hw_lock(bp, |
| HW_LOCK_RESOURCE_RESERVED_08)) |
| bp->is_leader = 1; |
| |
| /* Stop the driver */ |
| /* If interface has been removed - break */ |
| if (bnx2x_nic_unload(bp, UNLOAD_RECOVERY)) |
| return; |
| |
| bp->recovery_state = BNX2X_RECOVERY_WAIT; |
| /* Ensure "is_leader" and "recovery_state" |
| * update values are seen on other CPUs |
| */ |
| smp_wmb(); |
| break; |
| |
| case BNX2X_RECOVERY_WAIT: |
| DP(NETIF_MSG_HW, "State is BNX2X_RECOVERY_WAIT\n"); |
| if (bp->is_leader) { |
| u32 load_counter = bnx2x_get_load_cnt(bp); |
| if (load_counter) { |
| /* Wait until all other functions get |
| * down. |
| */ |
| schedule_delayed_work(&bp->reset_task, |
| HZ/10); |
| return; |
| } else { |
| /* If all other functions got down - |
| * try to bring the chip back to |
| * normal. In any case it's an exit |
| * point for a leader. |
| */ |
| if (bnx2x_leader_reset(bp) || |
| bnx2x_nic_load(bp, LOAD_NORMAL)) { |
| printk(KERN_ERR"%s: Recovery " |
| "has failed. Power cycle is " |
| "needed.\n", bp->dev->name); |
| /* Disconnect this device */ |
| netif_device_detach(bp->dev); |
| /* Block ifup for all function |
| * of this ASIC until |
| * "process kill" or power |
| * cycle. |
| */ |
| bnx2x_set_reset_in_progress(bp); |
| /* Shut down the power */ |
| bnx2x_set_power_state(bp, |
| PCI_D3hot); |
| return; |
| } |
| |
| return; |
| } |
| } else { /* non-leader */ |
| if (!bnx2x_reset_is_done(bp)) { |
| /* Try to get a LEADER_LOCK HW lock as |
| * long as a former leader may have |
| * been unloaded by the user or |
| * released a leadership by another |
| * reason. |
| */ |
| if (bnx2x_trylock_hw_lock(bp, |
| HW_LOCK_RESOURCE_RESERVED_08)) { |
| /* I'm a leader now! Restart a |
| * switch case. |
| */ |
| bp->is_leader = 1; |
| break; |
| } |
| |
| schedule_delayed_work(&bp->reset_task, |
| HZ/10); |
| return; |
| |
| } else { /* A leader has completed |
| * the "process kill". It's an exit |
| * point for a non-leader. |
| */ |
| bnx2x_nic_load(bp, LOAD_NORMAL); |
| bp->recovery_state = |
| BNX2X_RECOVERY_DONE; |
| smp_wmb(); |
| return; |
| } |
| } |
| default: |
| return; |
| } |
| } |
| } |
| |
| /* bnx2x_nic_unload() flushes the bnx2x_wq, thus reset task is |
| * scheduled on a general queue in order to prevent a dead lock. |
| */ |
| static void bnx2x_reset_task(struct work_struct *work) |
| { |
| struct bnx2x *bp = container_of(work, struct bnx2x, reset_task.work); |
| |
| #ifdef BNX2X_STOP_ON_ERROR |
| BNX2X_ERR("reset task called but STOP_ON_ERROR defined" |
| " so reset not done to allow debug dump,\n" |
| KERN_ERR " you will need to reboot when done\n"); |
| return; |
| #endif |
| |
| rtnl_lock(); |
| |
| if (!netif_running(bp->dev)) |
| goto reset_task_exit; |
| |
| if (unlikely(bp->recovery_state != BNX2X_RECOVERY_DONE)) |
| bnx2x_parity_recover(bp); |
| else { |
| bnx2x_nic_unload(bp, UNLOAD_NORMAL); |
| bnx2x_nic_load(bp, LOAD_NORMAL); |
| } |
| |
| reset_task_exit: |
| rtnl_unlock(); |
| } |
| |
| /* end of nic load/unload */ |
| |
| /* |
| * Init service functions |
| */ |
| |
| static inline u32 bnx2x_get_pretend_reg(struct bnx2x *bp, int func) |
| { |
| switch (func) { |
| case 0: return PXP2_REG_PGL_PRETEND_FUNC_F0; |
| case 1: return PXP2_REG_PGL_PRETEND_FUNC_F1; |
| case 2: return PXP2_REG_PGL_PRETEND_FUNC_F2; |
| case 3: return PXP2_REG_PGL_PRETEND_FUNC_F3; |
| case 4: return PXP2_REG_PGL_PRETEND_FUNC_F4; |
| case 5: return PXP2_REG_PGL_PRETEND_FUNC_F5; |
| case 6: return PXP2_REG_PGL_PRETEND_FUNC_F6; |
| case 7: return PXP2_REG_PGL_PRETEND_FUNC_F7; |
| default: |
| BNX2X_ERR("Unsupported function index: %d\n", func); |
| return (u32)(-1); |
| } |
| } |
| |
| static void bnx2x_undi_int_disable_e1h(struct bnx2x *bp, int orig_func) |
| { |
| u32 reg = bnx2x_get_pretend_reg(bp, orig_func), new_val; |
| |
| /* Flush all outstanding writes */ |
| mmiowb(); |
| |
| /* Pretend to be function 0 */ |
| REG_WR(bp, reg, 0); |
| /* Flush the GRC transaction (in the chip) */ |
| new_val = REG_RD(bp, reg); |
| if (new_val != 0) { |
| BNX2X_ERR("Hmmm... Pretend register wasn't updated: (0,%d)!\n", |
| new_val); |
| BUG(); |
| } |
| |
| /* From now we are in the "like-E1" mode */ |
| bnx2x_int_disable(bp); |
| |
| /* Flush all outstanding writes */ |
| mmiowb(); |
| |
| /* Restore the original funtion settings */ |
| REG_WR(bp, reg, orig_func); |
| new_val = REG_RD(bp, reg); |
| if (new_val != orig_func) { |
| BNX2X_ERR("Hmmm... Pretend register wasn't updated: (%d,%d)!\n", |
| orig_func, new_val); |
| BUG(); |
| } |
| } |
| |
| static inline void bnx2x_undi_int_disable(struct bnx2x *bp, int func) |
| { |
| if (CHIP_IS_E1H(bp)) |
| bnx2x_undi_int_disable_e1h(bp, func); |
| else |
| bnx2x_int_disable(bp); |
| } |
| |
| static void __devinit bnx2x_undi_unload(struct bnx2x *bp) |
| { |
| u32 val; |
| |
| /* Check if there is any driver already loaded */ |
| val = REG_RD(bp, MISC_REG_UNPREPARED); |
| if (val == 0x1) { |
| /* Check if it is the UNDI driver |
| * UNDI driver initializes CID offset for normal bell to 0x7 |
| */ |
| bnx2x_acquire_hw_lock(bp, HW_LOCK_RESOURCE_UNDI); |
| val = REG_RD(bp, DORQ_REG_NORM_CID_OFST); |
| if (val == 0x7) { |
| u32 reset_code = DRV_MSG_CODE_UNLOAD_REQ_WOL_DIS; |
| /* save our func */ |
| int func = BP_FUNC(bp); |
| u32 swap_en; |
| u32 swap_val; |
| |
| /* clear the UNDI indication */ |
| REG_WR(bp, DORQ_REG_NORM_CID_OFST, 0); |
| |
| BNX2X_DEV_INFO("UNDI is active! reset device\n"); |
| |
| /* try unload UNDI on port 0 */ |
| bp->func = 0; |
| bp->fw_seq = |
| (SHMEM_RD(bp, func_mb[bp->func].drv_mb_header) & |
| DRV_MSG_SEQ_NUMBER_MASK); |
| reset_code = bnx2x_fw_command(bp, reset_code, 0); |
| |
| /* if UNDI is loaded on the other port */ |
| if (reset_code != FW_MSG_CODE_DRV_UNLOAD_COMMON) { |
| |
| /* send "DONE" for previous unload */ |
| bnx2x_fw_command(bp, |
| DRV_MSG_CODE_UNLOAD_DONE, 0); |
| |
| /* unload UNDI on port 1 */ |
| bp->func = 1; |
| bp->fw_seq = |
| (SHMEM_RD(bp, func_mb[bp->func].drv_mb_header) & |
| DRV_MSG_SEQ_NUMBER_MASK); |
| reset_code = DRV_MSG_CODE_UNLOAD_REQ_WOL_DIS; |
| |
| bnx2x_fw_command(bp, reset_code, 0); |
| } |
| |
| /* now it's safe to release the lock */ |
| bnx2x_release_hw_lock(bp, HW_LOCK_RESOURCE_UNDI); |
| |
| bnx2x_undi_int_disable(bp, func); |
| |
| /* close input traffic and wait for it */ |
| /* Do not rcv packets to BRB */ |
| REG_WR(bp, |
| (BP_PORT(bp) ? NIG_REG_LLH1_BRB1_DRV_MASK : |
| NIG_REG_LLH0_BRB1_DRV_MASK), 0x0); |
| /* Do not direct rcv packets that are not for MCP to |
| * the BRB */ |
| REG_WR(bp, |
| (BP_PORT(bp) ? NIG_REG_LLH1_BRB1_NOT_MCP : |
| NIG_REG_LLH0_BRB1_NOT_MCP), 0x0); |
| /* clear AEU */ |
| REG_WR(bp, |
| (BP_PORT(bp) ? MISC_REG_AEU_MASK_ATTN_FUNC_1 : |
| MISC_REG_AEU_MASK_ATTN_FUNC_0), 0); |
| msleep(10); |
| |
| /* save NIG port swap info */ |
| swap_val = REG_RD(bp, NIG_REG_PORT_SWAP); |
| swap_en = REG_RD(bp, NIG_REG_STRAP_OVERRIDE); |
| /* reset device */ |
| REG_WR(bp, |
| GRCBASE_MISC + MISC_REGISTERS_RESET_REG_1_CLEAR, |
| 0xd3ffffff); |
| REG_WR(bp, |
| GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR, |
| 0x1403); |
| /* take the NIG out of reset and restore swap values */ |
| REG_WR(bp, |
| GRCBASE_MISC + MISC_REGISTERS_RESET_REG_1_SET, |
| MISC_REGISTERS_RESET_REG_1_RST_NIG); |
| REG_WR(bp, NIG_REG_PORT_SWAP, swap_val); |
| REG_WR(bp, NIG_REG_STRAP_OVERRIDE, swap_en); |
| |
| /* send unload done to the MCP */ |
| bnx2x_fw_command(bp, DRV_MSG_CODE_UNLOAD_DONE, 0); |
| |
| /* restore our func and fw_seq */ |
| bp->func = func; |
| bp->fw_seq = |
| (SHMEM_RD(bp, func_mb[bp->func].drv_mb_header) & |
| DRV_MSG_SEQ_NUMBER_MASK); |
| |
| } else |
| bnx2x_release_hw_lock(bp, HW_LOCK_RESOURCE_UNDI); |
| } |
| } |
| |
| static void __devinit bnx2x_get_common_hwinfo(struct bnx2x *bp) |
| { |
| u32 val, val2, val3, val4, id; |
| u16 pmc; |
| |
| /* Get the chip revision id and number. */ |
| /* chip num:16-31, rev:12-15, metal:4-11, bond_id:0-3 */ |
| val = REG_RD(bp, MISC_REG_CHIP_NUM); |
| id = ((val & 0xffff) << 16); |
| val = REG_RD(bp, MISC_REG_CHIP_REV); |
| id |= ((val & 0xf) << 12); |
| val = REG_RD(bp, MISC_REG_CHIP_METAL); |
| id |= ((val & 0xff) << 4); |
| val = REG_RD(bp, MISC_REG_BOND_ID); |
| id |= (val & 0xf); |
| bp->common.chip_id = id; |
| bp->link_params.chip_id = bp->common.chip_id; |
| BNX2X_DEV_INFO("chip ID is 0x%x\n", id); |
| |
| val = (REG_RD(bp, 0x2874) & 0x55); |
| if ((bp->common.chip_id & 0x1) || |
| (CHIP_IS_E1(bp) && val) || (CHIP_IS_E1H(bp) && (val == 0x55))) { |
| bp->flags |= ONE_PORT_FLAG; |
| BNX2X_DEV_INFO("single port device\n"); |
| } |
| |
| val = REG_RD(bp, MCP_REG_MCPR_NVM_CFG4); |
| bp->common.flash_size = (NVRAM_1MB_SIZE << |
| (val & MCPR_NVM_CFG4_FLASH_SIZE)); |
| BNX2X_DEV_INFO("flash_size 0x%x (%d)\n", |
| bp->common.flash_size, bp->common.flash_size); |
| |
| bp->common.shmem_base = REG_RD(bp, MISC_REG_SHARED_MEM_ADDR); |
| bp->common.shmem2_base = REG_RD(bp, MISC_REG_GENERIC_CR_0); |
| bp->link_params.shmem_base = bp->common.shmem_base; |
| bp->link_params.shmem2_base = bp->common.shmem2_base; |
| BNX2X_DEV_INFO("shmem offset 0x%x shmem2 offset 0x%x\n", |
| bp->common.shmem_base, bp->common.shmem2_base); |
| |
| if (!bp->common.shmem_base || |
| (bp->common.shmem_base < 0xA0000) || |
| (bp->common.shmem_base >= 0xC0000)) { |
| BNX2X_DEV_INFO("MCP not active\n"); |
| bp->flags |= NO_MCP_FLAG; |
| return; |
| } |
| |
| val = SHMEM_RD(bp, validity_map[BP_PORT(bp)]); |
| if ((val & (SHR_MEM_VALIDITY_DEV_INFO | SHR_MEM_VALIDITY_MB)) |
| != (SHR_MEM_VALIDITY_DEV_INFO | SHR_MEM_VALIDITY_MB)) |
| BNX2X_ERROR("BAD MCP validity signature\n"); |
| |
| bp->common.hw_config = SHMEM_RD(bp, dev_info.shared_hw_config.config); |
| BNX2X_DEV_INFO("hw_config 0x%08x\n", bp->common.hw_config); |
| |
| bp->link_params.hw_led_mode = ((bp->common.hw_config & |
| SHARED_HW_CFG_LED_MODE_MASK) >> |
| SHARED_HW_CFG_LED_MODE_SHIFT); |
| |
| bp->link_params.feature_config_flags = 0; |
| val = SHMEM_RD(bp, dev_info.shared_feature_config.config); |
| if (val & SHARED_FEAT_CFG_OVERRIDE_PREEMPHASIS_CFG_ENABLED) |
| bp->link_params.feature_config_flags |= |
| FEATURE_CONFIG_OVERRIDE_PREEMPHASIS_ENABLED; |
| else |
| bp->link_params.feature_config_flags &= |
| ~FEATURE_CONFIG_OVERRIDE_PREEMPHASIS_ENABLED; |
| |
| val = SHMEM_RD(bp, dev_info.bc_rev) >> 8; |
| bp->common.bc_ver = val; |
| BNX2X_DEV_INFO("bc_ver %X\n", val); |
| if (val < BNX2X_BC_VER) { |
| /* for now only warn |
| * later we might need to enforce this */ |
| BNX2X_ERROR("This driver needs bc_ver %X but found %X, " |
| "please upgrade BC\n", BNX2X_BC_VER, val); |
| } |
| bp->link_params.feature_config_flags |= |
| (val >= REQ_BC_VER_4_VRFY_FIRST_PHY_OPT_MDL) ? |
| FEATURE_CONFIG_BC_SUPPORTS_OPT_MDL_VRFY : 0; |
| bp->link_params.feature_config_flags |= |
| (val >= REQ_BC_VER_4_VRFY_SPECIFIC_PHY_OPT_MDL) ? |
| FEATURE_CONFIG_BC_SUPPORTS_DUAL_PHY_OPT_MDL_VRFY : 0; |
| |
| if (BP_E1HVN(bp) == 0) { |
| pci_read_config_word(bp->pdev, bp->pm_cap + PCI_PM_PMC, &pmc); |
| bp->flags |= (pmc & PCI_PM_CAP_PME_D3cold) ? 0 : NO_WOL_FLAG; |
| } else { |
| /* no WOL capability for E1HVN != 0 */ |
| bp->flags |= NO_WOL_FLAG; |
| } |
| BNX2X_DEV_INFO("%sWoL capable\n", |
| (bp->flags & NO_WOL_FLAG) ? "not " : ""); |
| |
| val = SHMEM_RD(bp, dev_info.shared_hw_config.part_num); |
| val2 = SHMEM_RD(bp, dev_info.shared_hw_config.part_num[4]); |
| val3 = SHMEM_RD(bp, dev_info.shared_hw_config.part_num[8]); |
| val4 = SHMEM_RD(bp, dev_info.shared_hw_config.part_num[12]); |
| |
| dev_info(&bp->pdev->dev, "part number %X-%X-%X-%X\n", |
| val, val2, val3, val4); |
| } |
| |
| static void __devinit bnx2x_link_settings_supported(struct bnx2x *bp, |
| u32 switch_cfg) |
| { |
| int cfg_size = 0, idx, port = BP_PORT(bp); |
| |
| /* Aggregation of supported attributes of all external phys */ |
| bp->port.supported[0] = 0; |
| bp->port.supported[1] = 0; |
| switch (bp->link_params.num_phys) { |
| case 1: |
| bp->port.supported[0] = bp->link_params.phy[INT_PHY].supported; |
| cfg_size = 1; |
| break; |
| case 2: |
| bp->port.supported[0] = bp->link_params.phy[EXT_PHY1].supported; |
| cfg_size = 1; |
| break; |
| case 3: |
| if (bp->link_params.multi_phy_config & |
| PORT_HW_CFG_PHY_SWAPPED_ENABLED) { |
| bp->port.supported[1] = |
| bp->link_params.phy[EXT_PHY1].supported; |
| bp->port.supported[0] = |
| bp->link_params.phy[EXT_PHY2].supported; |
| } else { |
| bp->port.supported[0] = |
| bp->link_params.phy[EXT_PHY1].supported; |
| bp->port.supported[1] = |
| bp->link_params.phy[EXT_PHY2].supported; |
| } |
| cfg_size = 2; |
| break; |
| } |
| |
| if (!(bp->port.supported[0] || bp->port.supported[1])) { |
| BNX2X_ERR("NVRAM config error. BAD phy config." |
| "PHY1 config 0x%x, PHY2 config 0x%x\n", |
| SHMEM_RD(bp, |
| dev_info.port_hw_config[port].external_phy_config), |
| SHMEM_RD(bp, |
| dev_info.port_hw_config[port].external_phy_config2)); |
| return; |
| } |
| |
| switch (switch_cfg) { |
| case SWITCH_CFG_1G: |
| bp->port.phy_addr = REG_RD(bp, NIG_REG_SERDES0_CTRL_PHY_ADDR + |
| port*0x10); |
| BNX2X_DEV_INFO("phy_addr 0x%x\n", bp->port.phy_addr); |
| break; |
| |
| case SWITCH_CFG_10G: |
| bp->port.phy_addr = REG_RD(bp, NIG_REG_XGXS0_CTRL_PHY_ADDR + |
| port*0x18); |
| BNX2X_DEV_INFO("phy_addr 0x%x\n", bp->port.phy_addr); |
| |
| break; |
| |
| default: |
| BNX2X_ERR("BAD switch_cfg link_config 0x%x\n", |
| bp->port.link_config[0]); |
| return; |
| } |
| /* mask what we support according to speed_cap_mask per configuration */ |
| for (idx = 0; idx < cfg_size; idx++) { |
| if (!(bp->link_params.speed_cap_mask[idx] & |
| PORT_HW_CFG_SPEED_CAPABILITY_D0_10M_HALF)) |
| bp->port.supported[idx] &= ~SUPPORTED_10baseT_Half; |
| |
| if (!(bp->link_params.speed_cap_mask[idx] & |
| PORT_HW_CFG_SPEED_CAPABILITY_D0_10M_FULL)) |
| bp->port.supported[idx] &= ~SUPPORTED_10baseT_Full; |
| |
| if (!(bp->link_params.speed_cap_mask[idx] & |
| PORT_HW_CFG_SPEED_CAPABILITY_D0_100M_HALF)) |
| bp->port.supported[idx] &= ~SUPPORTED_100baseT_Half; |
| |
| if (!(bp->link_params.speed_cap_mask[idx] & |
| PORT_HW_CFG_SPEED_CAPABILITY_D0_100M_FULL)) |
| bp->port.supported[idx] &= ~SUPPORTED_100baseT_Full; |
| |
| if (!(bp->link_params.speed_cap_mask[idx] & |
| PORT_HW_CFG_SPEED_CAPABILITY_D0_1G)) |
| bp->port.supported[idx] &= ~(SUPPORTED_1000baseT_Half | |
| SUPPORTED_1000baseT_Full); |
| |
| if (!(bp->link_params.speed_cap_mask[idx] & |
| PORT_HW_CFG_SPEED_CAPABILITY_D0_2_5G)) |
| bp->port.supported[idx] &= ~SUPPORTED_2500baseX_Full; |
| |
| if (!(bp->link_params.speed_cap_mask[idx] & |
| PORT_HW_CFG_SPEED_CAPABILITY_D0_10G)) |
| bp->port.supported[idx] &= ~SUPPORTED_10000baseT_Full; |
| |
| } |
| |
| BNX2X_DEV_INFO("supported 0x%x 0x%x\n", bp->port.supported[0], |
| bp->port.supported[1]); |
| } |
| |
| static void __devinit bnx2x_link_settings_requested(struct bnx2x *bp) |
| { |
| u32 link_config, idx, cfg_size = 0; |
| bp->port.advertising[0] = 0; |
| bp->port.advertising[1] = 0; |
| switch (bp->link_params.num_phys) { |
| case 1: |
| case 2: |
| cfg_size = 1; |
| break; |
| case 3: |
| cfg_size = 2; |
| break; |
| } |
| for (idx = 0; idx < cfg_size; idx++) { |
| bp->link_params.req_duplex[idx] = DUPLEX_FULL; |
| link_config = bp->port.link_config[idx]; |
| switch (link_config & PORT_FEATURE_LINK_SPEED_MASK) { |
| case PORT_FEATURE_LINK_SPEED_AUTO: |
| if (bp->port.supported[idx] & SUPPORTED_Autoneg) { |
| bp->link_params.req_line_speed[idx] = |
| SPEED_AUTO_NEG; |
| bp->port.advertising[idx] |= |
| bp->port.supported[idx]; |
| } else { |
| /* force 10G, no AN */ |
| bp->link_params.req_line_speed[idx] = |
| SPEED_10000; |
| bp->port.advertising[idx] |= |
| (ADVERTISED_10000baseT_Full | |
| ADVERTISED_FIBRE); |
| continue; |
| } |
| break; |
| |
| case PORT_FEATURE_LINK_SPEED_10M_FULL: |
| if (bp->port.supported[idx] & SUPPORTED_10baseT_Full) { |
| bp->link_params.req_line_speed[idx] = |
| SPEED_10; |
| bp->port.advertising[idx] |= |
| (ADVERTISED_10baseT_Full | |
| ADVERTISED_TP); |
| } else { |
| BNX2X_ERROR("NVRAM config error. " |
| "Invalid link_config 0x%x" |
| " speed_cap_mask 0x%x\n", |
| link_config, |
| bp->link_params.speed_cap_mask[idx]); |
| return; |
| } |
| break; |
| |
| case PORT_FEATURE_LINK_SPEED_10M_HALF: |
| if (bp->port.supported[idx] & SUPPORTED_10baseT_Half) { |
| bp->link_params.req_line_speed[idx] = |
| SPEED_10; |
| bp->link_params.req_duplex[idx] = |
| DUPLEX_HALF; |
| bp->port.advertising[idx] |= |
| (ADVERTISED_10baseT_Half | |
| ADVERTISED_TP); |
| } else { |
| BNX2X_ERROR("NVRAM config error. " |
| "Invalid link_config 0x%x" |
| " speed_cap_mask 0x%x\n", |
| link_config, |
| bp->link_params.speed_cap_mask[idx]); |
| return; |
| } |
| break; |
| |
| case PORT_FEATURE_LINK_SPEED_100M_FULL: |
| if (bp->port.supported[idx] & SUPPORTED_100baseT_Full) { |
| bp->link_params.req_line_speed[idx] = |
| SPEED_100; |
| bp->port.advertising[idx] |= |
| (ADVERTISED_100baseT_Full | |
| ADVERTISED_TP); |
| } else { |
| BNX2X_ERROR("NVRAM config error. " |
| "Invalid link_config 0x%x" |
| " speed_cap_mask 0x%x\n", |
| link_config, |
| bp->link_params.speed_cap_mask[idx]); |
| return; |
| } |
| break; |
| |
| case PORT_FEATURE_LINK_SPEED_100M_HALF: |
| if (bp->port.supported[idx] & SUPPORTED_100baseT_Half) { |
| bp->link_params.req_line_speed[idx] = SPEED_100; |
| bp->link_params.req_duplex[idx] = DUPLEX_HALF; |
| bp->port.advertising[idx] |= |
| (ADVERTISED_100baseT_Half | |
| ADVERTISED_TP); |
| } else { |
| BNX2X_ERROR("NVRAM config error. " |
| "Invalid link_config 0x%x" |
| " speed_cap_mask 0x%x\n", |
| link_config, |
| bp->link_params.speed_cap_mask[idx]); |
| return; |
| } |
| break; |
| |
| case PORT_FEATURE_LINK_SPEED_1G: |
| if (bp->port.supported[idx] & |
| SUPPORTED_1000baseT_Full) { |
| bp->link_params.req_line_speed[idx] = |
| SPEED_1000; |
| bp->port.advertising[idx] |= |
| (ADVERTISED_1000baseT_Full | |
| ADVERTISED_TP); |
| } else { |
| BNX2X_ERROR("NVRAM config error. " |
| "Invalid link_config 0x%x" |
| " speed_cap_mask 0x%x\n", |
| link_config, |
| bp->link_params.speed_cap_mask[idx]); |
| return; |
| } |
| break; |
| |
| case PORT_FEATURE_LINK_SPEED_2_5G: |
| if (bp->port.supported[idx] & |
| SUPPORTED_2500baseX_Full) { |
| bp->link_params.req_line_speed[idx] = |
| SPEED_2500; |
| bp->port.advertising[idx] |= |
| (ADVERTISED_2500baseX_Full | |
| ADVERTISED_TP); |
| } else { |
| BNX2X_ERROR("NVRAM config error. " |
| "Invalid link_config 0x%x" |
| " speed_cap_mask 0x%x\n", |
| link_config, |
| bp->link_params.speed_cap_mask[idx]); |
| return; |
| } |
| break; |
| |
| case PORT_FEATURE_LINK_SPEED_10G_CX4: |
| case PORT_FEATURE_LINK_SPEED_10G_KX4: |
| case PORT_FEATURE_LINK_SPEED_10G_KR: |
| if (bp->port.supported[idx] & |
| SUPPORTED_10000baseT_Full) { |
| bp->link_params.req_line_speed[idx] = |
| SPEED_10000; |
| bp->port.advertising[idx] |= |
| (ADVERTISED_10000baseT_Full | |
| ADVERTISED_FIBRE); |
| } else { |
| BNX2X_ERROR("NVRAM config error. " |
| "Invalid link_config 0x%x" |
| " speed_cap_mask 0x%x\n", |
| link_config, |
| bp->link_params.speed_cap_mask[idx]); |
| return; |
| } |
| break; |
| |
| default: |
| BNX2X_ERROR("NVRAM config error. " |
| "BAD link speed link_config 0x%x\n", |
| link_config); |
| bp->link_params.req_line_speed[idx] = SPEED_AUTO_NEG; |
| bp->port.advertising[idx] = bp->port.supported[idx]; |
| break; |
| } |
| |
| bp->link_params.req_flow_ctrl[idx] = (link_config & |
| PORT_FEATURE_FLOW_CONTROL_MASK); |
| if ((bp->link_params.req_flow_ctrl[idx] == |
| BNX2X_FLOW_CTRL_AUTO) && |
| !(bp->port.supported[idx] & SUPPORTED_Autoneg)) { |
| bp->link_params.req_flow_ctrl[idx] = |
| BNX2X_FLOW_CTRL_NONE; |
| } |
| |
| BNX2X_DEV_INFO("req_line_speed %d req_duplex %d req_flow_ctrl" |
| " 0x%x advertising 0x%x\n", |
| bp->link_params.req_line_speed[idx], |
| bp->link_params.req_duplex[idx], |
| bp->link_params.req_flow_ctrl[idx], |
| bp->port.advertising[idx]); |
| } |
| } |
| |
| static void __devinit bnx2x_set_mac_buf(u8 *mac_buf, u32 mac_lo, u16 mac_hi) |
| { |
| mac_hi = cpu_to_be16(mac_hi); |
| mac_lo = cpu_to_be32(mac_lo); |
| memcpy(mac_buf, &mac_hi, sizeof(mac_hi)); |
| memcpy(mac_buf + sizeof(mac_hi), &mac_lo, sizeof(mac_lo)); |
| } |
| |
| static void __devinit bnx2x_get_port_hwinfo(struct bnx2x *bp) |
| { |
| int port = BP_PORT(bp); |
| u32 val, val2; |
| u32 config; |
| u32 ext_phy_type, ext_phy_config;; |
| |
| bp->link_params.bp = bp; |
| bp->link_params.port = port; |
| |
| bp->link_params.lane_config = |
| SHMEM_RD(bp, dev_info.port_hw_config[port].lane_config); |
| |
| bp->link_params.speed_cap_mask[0] = |
| SHMEM_RD(bp, |
| dev_info.port_hw_config[port].speed_capability_mask); |
| bp->link_params.speed_cap_mask[1] = |
| SHMEM_RD(bp, |
| dev_info.port_hw_config[port].speed_capability_mask2); |
| bp->port.link_config[0] = |
| SHMEM_RD(bp, dev_info.port_feature_config[port].link_config); |
| |
| bp->port.link_config[1] = |
| SHMEM_RD(bp, dev_info.port_feature_config[port].link_config2); |
| |
| bp->link_params.multi_phy_config = |
| SHMEM_RD(bp, dev_info.port_hw_config[port].multi_phy_config); |
| /* If the device is capable of WoL, set the default state according |
| * to the HW |
| */ |
| config = SHMEM_RD(bp, dev_info.port_feature_config[port].config); |
| bp->wol = (!(bp->flags & NO_WOL_FLAG) && |
| (config & PORT_FEATURE_WOL_ENABLED)); |
| |
| BNX2X_DEV_INFO("lane_config 0x%08x" |
| "speed_cap_mask0 0x%08x link_config0 0x%08x\n", |
| bp->link_params.lane_config, |
| bp->link_params.speed_cap_mask[0], |
| bp->port.link_config[0]); |
| |
| bp->link_params.switch_cfg = (bp->port.link_config[0] & |
| PORT_FEATURE_CONNECTED_SWITCH_MASK); |
| bnx2x_phy_probe(&bp->link_params); |
| bnx2x_link_settings_supported(bp, bp->link_params.switch_cfg); |
| |
| bnx2x_link_settings_requested(bp); |
| |
| /* |
| * If connected directly, work with the internal PHY, otherwise, work |
| * with the external PHY |
| */ |
| ext_phy_config = |
| SHMEM_RD(bp, |
| dev_info.port_hw_config[port].external_phy_config); |
| ext_phy_type = XGXS_EXT_PHY_TYPE(ext_phy_config); |
| if (ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT) |
| bp->mdio.prtad = bp->port.phy_addr; |
| |
| else if ((ext_phy_type != PORT_HW_CFG_XGXS_EXT_PHY_TYPE_FAILURE) && |
| (ext_phy_type != PORT_HW_CFG_XGXS_EXT_PHY_TYPE_NOT_CONN)) |
| bp->mdio.prtad = |
| XGXS_EXT_PHY_ADDR(ext_phy_config); |
| |
| val2 = SHMEM_RD(bp, dev_info.port_hw_config[port].mac_upper); |
| val = SHMEM_RD(bp, dev_info.port_hw_config[port].mac_lower); |
| bnx2x_set_mac_buf(bp->dev->dev_addr, val, val2); |
| memcpy(bp->link_params.mac_addr, bp->dev->dev_addr, ETH_ALEN); |
| memcpy(bp->dev->perm_addr, bp->dev->dev_addr, ETH_ALEN); |
| |
| #ifdef BCM_CNIC |
| val2 = SHMEM_RD(bp, dev_info.port_hw_config[port].iscsi_mac_upper); |
| val = SHMEM_RD(bp, dev_info.port_hw_config[port].iscsi_mac_lower); |
| bnx2x_set_mac_buf(bp->iscsi_mac, val, val2); |
| #endif |
| } |
| |
| static int __devinit bnx2x_get_hwinfo(struct bnx2x *bp) |
| { |
| int func = BP_FUNC(bp); |
| u32 val, val2; |
| int rc = 0; |
| |
| bnx2x_get_common_hwinfo(bp); |
| |
| bp->e1hov = 0; |
| bp->e1hmf = 0; |
| if (CHIP_IS_E1H(bp) && !BP_NOMCP(bp)) { |
| bp->mf_config = |
| SHMEM_RD(bp, mf_cfg.func_mf_config[func].config); |
| |
| val = (SHMEM_RD(bp, mf_cfg.func_mf_config[FUNC_0].e1hov_tag) & |
| FUNC_MF_CFG_E1HOV_TAG_MASK); |
| if (val != FUNC_MF_CFG_E1HOV_TAG_DEFAULT) |
| bp->e1hmf = 1; |
| BNX2X_DEV_INFO("%s function mode\n", |
| IS_E1HMF(bp) ? "multi" : "single"); |
| |
| if (IS_E1HMF(bp)) { |
| val = (SHMEM_RD(bp, mf_cfg.func_mf_config[func]. |
| e1hov_tag) & |
| FUNC_MF_CFG_E1HOV_TAG_MASK); |
| if (val != FUNC_MF_CFG_E1HOV_TAG_DEFAULT) { |
| bp->e1hov = val; |
| BNX2X_DEV_INFO("E1HOV for func %d is %d " |
| "(0x%04x)\n", |
| func, bp->e1hov, bp->e1hov); |
| } else { |
| BNX2X_ERROR("No valid E1HOV for func %d," |
| " aborting\n", func); |
| rc = -EPERM; |
| } |
| } else { |
| if (BP_E1HVN(bp)) { |
| BNX2X_ERROR("VN %d in single function mode," |
| " aborting\n", BP_E1HVN(bp)); |
| rc = -EPERM; |
| } |
| } |
| } |
| |
| if (!BP_NOMCP(bp)) { |
| bnx2x_get_port_hwinfo(bp); |
| |
| bp->fw_seq = (SHMEM_RD(bp, func_mb[func].drv_mb_header) & |
| DRV_MSG_SEQ_NUMBER_MASK); |
| BNX2X_DEV_INFO("fw_seq 0x%08x\n", bp->fw_seq); |
| } |
| |
| if (IS_E1HMF(bp)) { |
| val2 = SHMEM_RD(bp, mf_cfg.func_mf_config[func].mac_upper); |
| val = SHMEM_RD(bp, mf_cfg.func_mf_config[func].mac_lower); |
| if ((val2 != FUNC_MF_CFG_UPPERMAC_DEFAULT) && |
| (val != FUNC_MF_CFG_LOWERMAC_DEFAULT)) { |
| bp->dev->dev_addr[0] = (u8)(val2 >> 8 & 0xff); |
| bp->dev->dev_addr[1] = (u8)(val2 & 0xff); |
| bp->dev->dev_addr[2] = (u8)(val >> 24 & 0xff); |
| bp->dev->dev_addr[3] = (u8)(val >> 16 & 0xff); |
| bp->dev->dev_addr[4] = (u8)(val >> 8 & 0xff); |
| bp->dev->dev_addr[5] = (u8)(val & 0xff); |
| memcpy(bp->link_params.mac_addr, bp->dev->dev_addr, |
| ETH_ALEN); |
| memcpy(bp->dev->perm_addr, bp->dev->dev_addr, |
| ETH_ALEN); |
| } |
| |
| return rc; |
| } |
| |
| if (BP_NOMCP(bp)) { |
| /* only supposed to happen on emulation/FPGA */ |
| BNX2X_ERROR("warning: random MAC workaround active\n"); |
| random_ether_addr(bp->dev->dev_addr); |
| memcpy(bp->dev->perm_addr, bp->dev->dev_addr, ETH_ALEN); |
| } |
| |
| return rc; |
| } |
| |
| static void __devinit bnx2x_read_fwinfo(struct bnx2x *bp) |
| { |
| int cnt, i, block_end, rodi; |
| char vpd_data[BNX2X_VPD_LEN+1]; |
| char str_id_reg[VENDOR_ID_LEN+1]; |
| char str_id_cap[VENDOR_ID_LEN+1]; |
| u8 len; |
| |
| cnt = pci_read_vpd(bp->pdev, 0, BNX2X_VPD_LEN, vpd_data); |
| memset(bp->fw_ver, 0, sizeof(bp->fw_ver)); |
| |
| if (cnt < BNX2X_VPD_LEN) |
| goto out_not_found; |
| |
| i = pci_vpd_find_tag(vpd_data, 0, BNX2X_VPD_LEN, |
| PCI_VPD_LRDT_RO_DATA); |
| if (i < 0) |
| goto out_not_found; |
| |
| |
| block_end = i + PCI_VPD_LRDT_TAG_SIZE + |
| pci_vpd_lrdt_size(&vpd_data[i]); |
| |
| i += PCI_VPD_LRDT_TAG_SIZE; |
| |
| if (block_end > BNX2X_VPD_LEN) |
| goto out_not_found; |
| |
| rodi = pci_vpd_find_info_keyword(vpd_data, i, block_end, |
| PCI_VPD_RO_KEYWORD_MFR_ID); |
| if (rodi < 0) |
| goto out_not_found; |
| |
| len = pci_vpd_info_field_size(&vpd_data[rodi]); |
| |
| if (len != VENDOR_ID_LEN) |
| goto out_not_found; |
| |
| rodi += PCI_VPD_INFO_FLD_HDR_SIZE; |
| |
| /* vendor specific info */ |
| snprintf(str_id_reg, VENDOR_ID_LEN + 1, "%04x", PCI_VENDOR_ID_DELL); |
| snprintf(str_id_cap, VENDOR_ID_LEN + 1, "%04X", PCI_VENDOR_ID_DELL); |
| if (!strncmp(str_id_reg, &vpd_data[rodi], VENDOR_ID_LEN) || |
| !strncmp(str_id_cap, &vpd_data[rodi], VENDOR_ID_LEN)) { |
| |
| rodi = pci_vpd_find_info_keyword(vpd_data, i, block_end, |
| PCI_VPD_RO_KEYWORD_VENDOR0); |
| if (rodi >= 0) { |
| len = pci_vpd_info_field_size(&vpd_data[rodi]); |
| |
| rodi += PCI_VPD_INFO_FLD_HDR_SIZE; |
| |
| if (len < 32 && (len + rodi) <= BNX2X_VPD_LEN) { |
| memcpy(bp->fw_ver, &vpd_data[rodi], len); |
| bp->fw_ver[len] = ' '; |
| } |
| } |
| return; |
| } |
| out_not_found: |
| return; |
| } |
| |
| static int __devinit bnx2x_init_bp(struct bnx2x *bp) |
| { |
| int func = BP_FUNC(bp); |
| int timer_interval; |
| int rc; |
| |
| /* Disable interrupt handling until HW is initialized */ |
| atomic_set(&bp->intr_sem, 1); |
| smp_wmb(); /* Ensure that bp->intr_sem update is SMP-safe */ |
| |
| mutex_init(&bp->port.phy_mutex); |
| mutex_init(&bp->fw_mb_mutex); |
| spin_lock_init(&bp->stats_lock); |
| #ifdef BCM_CNIC |
| mutex_init(&bp->cnic_mutex); |
| #endif |
| |
| INIT_DELAYED_WORK(&bp->sp_task, bnx2x_sp_task); |
| INIT_DELAYED_WORK(&bp->reset_task, bnx2x_reset_task); |
| |
| rc = bnx2x_get_hwinfo(bp); |
| |
| bnx2x_read_fwinfo(bp); |
| /* need to reset chip if undi was active */ |
| if (!BP_NOMCP(bp)) |
| bnx2x_undi_unload(bp); |
| |
| if (CHIP_REV_IS_FPGA(bp)) |
| dev_err(&bp->pdev->dev, "FPGA detected\n"); |
| |
| if (BP_NOMCP(bp) && (func == 0)) |
| dev_err(&bp->pdev->dev, "MCP disabled, " |
| "must load devices in order!\n"); |
| |
| /* Set multi queue mode */ |
| if ((multi_mode != ETH_RSS_MODE_DISABLED) && |
| ((int_mode == INT_MODE_INTx) || (int_mode == INT_MODE_MSI))) { |
| dev_err(&bp->pdev->dev, "Multi disabled since int_mode " |
| "requested is not MSI-X\n"); |
| multi_mode = ETH_RSS_MODE_DISABLED; |
| } |
| bp->multi_mode = multi_mode; |
| bp->int_mode = int_mode; |
| |
| bp->dev->features |= NETIF_F_GRO; |
| |
| /* Set TPA flags */ |
| if (disable_tpa) { |
| bp->flags &= ~TPA_ENABLE_FLAG; |
| bp->dev->features &= ~NETIF_F_LRO; |
| } else { |
| bp->flags |= TPA_ENABLE_FLAG; |
| bp->dev->features |= NETIF_F_LRO; |
| } |
| bp->disable_tpa = disable_tpa; |
| |
| if (CHIP_IS_E1(bp)) |
| bp->dropless_fc = 0; |
| else |
| bp->dropless_fc = dropless_fc; |
| |
| bp->mrrs = mrrs; |
| |
| bp->tx_ring_size = MAX_TX_AVAIL; |
| bp->rx_ring_size = MAX_RX_AVAIL; |
| |
| bp->rx_csum = 1; |
| |
| /* make sure that the numbers are in the right granularity */ |
| bp->tx_ticks = (50 / (4 * BNX2X_BTR)) * (4 * BNX2X_BTR); |
| bp->rx_ticks = (25 / (4 * BNX2X_BTR)) * (4 * BNX2X_BTR); |
| |
| timer_interval = (CHIP_REV_IS_SLOW(bp) ? 5*HZ : HZ); |
| bp->current_interval = (poll ? poll : timer_interval); |
| |
| init_timer(&bp->timer); |
| bp->timer.expires = jiffies + bp->current_interval; |
| bp->timer.data = (unsigned long) bp; |
| bp->timer.function = bnx2x_timer; |
| |
| return rc; |
| } |
| |
| |
| /**************************************************************************** |
| * General service functions |
| ****************************************************************************/ |
| |
| /* called with rtnl_lock */ |
| static int bnx2x_open(struct net_device *dev) |
| { |
| struct bnx2x *bp = netdev_priv(dev); |
| |
| netif_carrier_off(dev); |
| |
| bnx2x_set_power_state(bp, PCI_D0); |
| |
| if (!bnx2x_reset_is_done(bp)) { |
| do { |
| /* Reset MCP mail box sequence if there is on going |
| * recovery |
| */ |
| bp->fw_seq = 0; |
| |
| /* If it's the first function to load and reset done |
| * is still not cleared it may mean that. We don't |
| * check the attention state here because it may have |
| * already been cleared by a "common" reset but we |
| * shell proceed with "process kill" anyway. |
| */ |
| if ((bnx2x_get_load_cnt(bp) == 0) && |
| bnx2x_trylock_hw_lock(bp, |
| HW_LOCK_RESOURCE_RESERVED_08) && |
| (!bnx2x_leader_reset(bp))) { |
| DP(NETIF_MSG_HW, "Recovered in open\n"); |
| break; |
| } |
| |
| bnx2x_set_power_state(bp, PCI_D3hot); |
| |
| printk(KERN_ERR"%s: Recovery flow hasn't been properly" |
| " completed yet. Try again later. If u still see this" |
| " message after a few retries then power cycle is" |
| " required.\n", bp->dev->name); |
| |
| return -EAGAIN; |
| } while (0); |
| } |
| |
| bp->recovery_state = BNX2X_RECOVERY_DONE; |
| |
| return bnx2x_nic_load(bp, LOAD_OPEN); |
| } |
| |
| /* called with rtnl_lock */ |
| static int bnx2x_close(struct net_device *dev) |
| { |
| struct bnx2x *bp = netdev_priv(dev); |
| |
| /* Unload the driver, release IRQs */ |
| bnx2x_nic_unload(bp, UNLOAD_CLOSE); |
| bnx2x_set_power_state(bp, PCI_D3hot); |
| |
| return 0; |
| } |
| |
| /* called with netif_tx_lock from dev_mcast.c */ |
| void bnx2x_set_rx_mode(struct net_device *dev) |
| { |
| struct bnx2x *bp = netdev_priv(dev); |
| u32 rx_mode = BNX2X_RX_MODE_NORMAL; |
| int port = BP_PORT(bp); |
| |
| if (bp->state != BNX2X_STATE_OPEN) { |
| DP(NETIF_MSG_IFUP, "state is %x, returning\n", bp->state); |
| return; |
| } |
| |
| DP(NETIF_MSG_IFUP, "dev->flags = %x\n", dev->flags); |
| |
| if (dev->flags & IFF_PROMISC) |
| rx_mode = BNX2X_RX_MODE_PROMISC; |
| |
| else if ((dev->flags & IFF_ALLMULTI) || |
| ((netdev_mc_count(dev) > BNX2X_MAX_MULTICAST) && |
| CHIP_IS_E1(bp))) |
| rx_mode = BNX2X_RX_MODE_ALLMULTI; |
| |
| else { /* some multicasts */ |
| if (CHIP_IS_E1(bp)) { |
| int i, old, offset; |
| struct netdev_hw_addr *ha; |
| struct mac_configuration_cmd *config = |
| bnx2x_sp(bp, mcast_config); |
| |
| i = 0; |
| netdev_for_each_mc_addr(ha, dev) { |
| config->config_table[i]. |
| cam_entry.msb_mac_addr = |
| swab16(*(u16 *)&ha->addr[0]); |
| config->config_table[i]. |
| cam_entry.middle_mac_addr = |
| swab16(*(u16 *)&ha->addr[2]); |
| config->config_table[i]. |
| cam_entry.lsb_mac_addr = |
| swab16(*(u16 *)&ha->addr[4]); |
| config->config_table[i].cam_entry.flags = |
| cpu_to_le16(port); |
| config->config_table[i]. |
| target_table_entry.flags = 0; |
| config->config_table[i].target_table_entry. |
| clients_bit_vector = |
| cpu_to_le32(1 << BP_L_ID(bp)); |
| config->config_table[i]. |
| target_table_entry.vlan_id = 0; |
| |
| DP(NETIF_MSG_IFUP, |
| "setting MCAST[%d] (%04x:%04x:%04x)\n", i, |
| config->config_table[i]. |
| cam_entry.msb_mac_addr, |
| config->config_table[i]. |
| cam_entry.middle_mac_addr, |
| config->config_table[i]. |
| cam_entry.lsb_mac_addr); |
| i++; |
| } |
| old = config->hdr.length; |
| if (old > i) { |
| for (; i < old; i++) { |
| if (CAM_IS_INVALID(config-> |
| config_table[i])) { |
| /* already invalidated */ |
| break; |
| } |
| /* invalidate */ |
| CAM_INVALIDATE(config-> |
| config_table[i]); |
| } |
| } |
| |
| if (CHIP_REV_IS_SLOW(bp)) |
| offset = BNX2X_MAX_EMUL_MULTI*(1 + port); |
| else |
| offset = BNX2X_MAX_MULTICAST*(1 + port); |
| |
| config->hdr.length = i; |
| config->hdr.offset = offset; |
| config->hdr.client_id = bp->fp->cl_id; |
| config->hdr.reserved1 = 0; |
| |
| bp->set_mac_pending++; |
| smp_wmb(); |
| |
| bnx2x_sp_post(bp, RAMROD_CMD_ID_ETH_SET_MAC, 0, |
| U64_HI(bnx2x_sp_mapping(bp, mcast_config)), |
| U64_LO(bnx2x_sp_mapping(bp, mcast_config)), |
| 0); |
| } else { /* E1H */ |
| /* Accept one or more multicasts */ |
| struct netdev_hw_addr *ha; |
| u32 mc_filter[MC_HASH_SIZE]; |
| u32 crc, bit, regidx; |
| int i; |
| |
| memset(mc_filter, 0, 4 * MC_HASH_SIZE); |
| |
| netdev_for_each_mc_addr(ha, dev) { |
| DP(NETIF_MSG_IFUP, "Adding mcast MAC: %pM\n", |
| ha->addr); |
| |
| crc = crc32c_le(0, ha->addr, ETH_ALEN); |
| bit = (crc >> 24) & 0xff; |
| regidx = bit >> 5; |
| bit &= 0x1f; |
| mc_filter[regidx] |= (1 << bit); |
| } |
| |
| for (i = 0; i < MC_HASH_SIZE; i++) |
| REG_WR(bp, MC_HASH_OFFSET(bp, i), |
| mc_filter[i]); |
| } |
| } |
| |
| bp->rx_mode = rx_mode; |
| bnx2x_set_storm_rx_mode(bp); |
| } |
| |
| |
| /* called with rtnl_lock */ |
| static int bnx2x_mdio_read(struct net_device *netdev, int prtad, |
| int devad, u16 addr) |
| { |
| struct bnx2x *bp = netdev_priv(netdev); |
| u16 value; |
| int rc; |
| |
| DP(NETIF_MSG_LINK, "mdio_read: prtad 0x%x, devad 0x%x, addr 0x%x\n", |
| prtad, devad, addr); |
| |
| /* The HW expects different devad if CL22 is used */ |
| devad = (devad == MDIO_DEVAD_NONE) ? DEFAULT_PHY_DEV_ADDR : devad; |
| |
| bnx2x_acquire_phy_lock(bp); |
| rc = bnx2x_phy_read(&bp->link_params, prtad, devad, addr, &value); |
| bnx2x_release_phy_lock(bp); |
| DP(NETIF_MSG_LINK, "mdio_read_val 0x%x rc = 0x%x\n", value, rc); |
| |
| if (!rc) |
| rc = value; |
| return rc; |
| } |
| |
| /* called with rtnl_lock */ |
| static int bnx2x_mdio_write(struct net_device *netdev, int prtad, int devad, |
| u16 addr, u16 value) |
| { |
| struct bnx2x *bp = netdev_priv(netdev); |
| int rc; |
| |
| DP(NETIF_MSG_LINK, "mdio_write: prtad 0x%x, devad 0x%x, addr 0x%x," |
| " value 0x%x\n", prtad, devad, addr, value); |
| |
| /* The HW expects different devad if CL22 is used */ |
| devad = (devad == MDIO_DEVAD_NONE) ? DEFAULT_PHY_DEV_ADDR : devad; |
| |
| bnx2x_acquire_phy_lock(bp); |
| rc = bnx2x_phy_write(&bp->link_params, prtad, devad, addr, value); |
| bnx2x_release_phy_lock(bp); |
| return rc; |
| } |
| |
| /* called with rtnl_lock */ |
| static int bnx2x_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd) |
| { |
| struct bnx2x *bp = netdev_priv(dev); |
| struct mii_ioctl_data *mdio = if_mii(ifr); |
| |
| DP(NETIF_MSG_LINK, "ioctl: phy id 0x%x, reg 0x%x, val_in 0x%x\n", |
| mdio->phy_id, mdio->reg_num, mdio->val_in); |
| |
| if (!netif_running(dev)) |
| return -EAGAIN; |
| |
| return mdio_mii_ioctl(&bp->mdio, mdio, cmd); |
| } |
| |
| #ifdef CONFIG_NET_POLL_CONTROLLER |
| static void poll_bnx2x(struct net_device *dev) |
| { |
| struct bnx2x *bp = netdev_priv(dev); |
| |
| disable_irq(bp->pdev->irq); |
| bnx2x_interrupt(bp->pdev->irq, dev); |
| enable_irq(bp->pdev->irq); |
| } |
| #endif |
| |
| static const struct net_device_ops bnx2x_netdev_ops = { |
| .ndo_open = bnx2x_open, |
| .ndo_stop = bnx2x_close, |
| .ndo_start_xmit = bnx2x_start_xmit, |
| .ndo_set_multicast_list = bnx2x_set_rx_mode, |
| .ndo_set_mac_address = bnx2x_change_mac_addr, |
| .ndo_validate_addr = eth_validate_addr, |
| .ndo_do_ioctl = bnx2x_ioctl, |
| .ndo_change_mtu = bnx2x_change_mtu, |
| .ndo_tx_timeout = bnx2x_tx_timeout, |
| #ifdef BCM_VLAN |
| .ndo_vlan_rx_register = bnx2x_vlan_rx_register, |
| #endif |
| #ifdef CONFIG_NET_POLL_CONTROLLER |
| .ndo_poll_controller = poll_bnx2x, |
| #endif |
| }; |
| |
| static int __devinit bnx2x_init_dev(struct pci_dev *pdev, |
| struct net_device *dev) |
| { |
| struct bnx2x *bp; |
| int rc; |
| |
| SET_NETDEV_DEV(dev, &pdev->dev); |
| bp = netdev_priv(dev); |
| |
| bp->dev = dev; |
| bp->pdev = pdev; |
| bp->flags = 0; |
| bp->func = PCI_FUNC(pdev->devfn); |
| |
| rc = pci_enable_device(pdev); |
| if (rc) { |
| dev_err(&bp->pdev->dev, |
| "Cannot enable PCI device, aborting\n"); |
| goto err_out; |
| } |
| |
| if (!(pci_resource_flags(pdev, 0) & IORESOURCE_MEM)) { |
| dev_err(&bp->pdev->dev, |
| "Cannot find PCI device base address, aborting\n"); |
| rc = -ENODEV; |
| goto err_out_disable; |
| } |
| |
| if (!(pci_resource_flags(pdev, 2) & IORESOURCE_MEM)) { |
| dev_err(&bp->pdev->dev, "Cannot find second PCI device" |
| " base address, aborting\n"); |
| rc = -ENODEV; |
| goto err_out_disable; |
| } |
| |
| if (atomic_read(&pdev->enable_cnt) == 1) { |
| rc = pci_request_regions(pdev, DRV_MODULE_NAME); |
| if (rc) { |
| dev_err(&bp->pdev->dev, |
| "Cannot obtain PCI resources, aborting\n"); |
| goto err_out_disable; |
| } |
| |
| pci_set_master(pdev); |
| pci_save_state(pdev); |
| } |
| |
| bp->pm_cap = pci_find_capability(pdev, PCI_CAP_ID_PM); |
| if (bp->pm_cap == 0) { |
| dev_err(&bp->pdev->dev, |
| "Cannot find power management capability, aborting\n"); |
| rc = -EIO; |
| goto err_out_release; |
| } |
| |
| bp->pcie_cap = pci_find_capability(pdev, PCI_CAP_ID_EXP); |
| if (bp->pcie_cap == 0) { |
| dev_err(&bp->pdev->dev, |
| "Cannot find PCI Express capability, aborting\n"); |
| rc = -EIO; |
| goto err_out_release; |
| } |
| |
| if (dma_set_mask(&pdev->dev, DMA_BIT_MASK(64)) == 0) { |
| bp->flags |= USING_DAC_FLAG; |
| if (dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(64)) != 0) { |
| dev_err(&bp->pdev->dev, "dma_set_coherent_mask" |
| " failed, aborting\n"); |
| rc = -EIO; |
| goto err_out_release; |
| } |
| |
| } else if (dma_set_mask(&pdev->dev, DMA_BIT_MASK(32)) != 0) { |
| dev_err(&bp->pdev->dev, |
| "System does not support DMA, aborting\n"); |
| rc = -EIO; |
| goto err_out_release; |
| } |
| |
| dev->mem_start = pci_resource_start(pdev, 0); |
| dev->base_addr = dev->mem_start; |
| dev->mem_end = pci_resource_end(pdev, 0); |
| |
| dev->irq = pdev->irq; |
| |
| bp->regview = pci_ioremap_bar(pdev, 0); |
| if (!bp->regview) { |
| dev_err(&bp->pdev->dev, |
| "Cannot map register space, aborting\n"); |
| rc = -ENOMEM; |
| goto err_out_release; |
| } |
| |
| bp->doorbells = ioremap_nocache(pci_resource_start(pdev, 2), |
| min_t(u64, BNX2X_DB_SIZE, |
| pci_resource_len(pdev, 2))); |
| if (!bp->doorbells) { |
| dev_err(&bp->pdev->dev, |
| "Cannot map doorbell space, aborting\n"); |
| rc = -ENOMEM; |
| goto err_out_unmap; |
| } |
| |
| bnx2x_set_power_state(bp, PCI_D0); |
| |
| /* clean indirect addresses */ |
| pci_write_config_dword(bp->pdev, PCICFG_GRC_ADDRESS, |
| PCICFG_VENDOR_ID_OFFSET); |
| REG_WR(bp, PXP2_REG_PGL_ADDR_88_F0 + BP_PORT(bp)*16, 0); |
| REG_WR(bp, PXP2_REG_PGL_ADDR_8C_F0 + BP_PORT(bp)*16, 0); |
| REG_WR(bp, PXP2_REG_PGL_ADDR_90_F0 + BP_PORT(bp)*16, 0); |
| REG_WR(bp, PXP2_REG_PGL_ADDR_94_F0 + BP_PORT(bp)*16, 0); |
| |
| /* Reset the load counter */ |
| bnx2x_clear_load_cnt(bp); |
| |
| dev->watchdog_timeo = TX_TIMEOUT; |
| |
| dev->netdev_ops = &bnx2x_netdev_ops; |
| bnx2x_set_ethtool_ops(dev); |
| dev->features |= NETIF_F_SG; |
| dev->features |= NETIF_F_HW_CSUM; |
| if (bp->flags & USING_DAC_FLAG) |
| dev->features |= NETIF_F_HIGHDMA; |
| dev->features |= (NETIF_F_TSO | NETIF_F_TSO_ECN); |
| dev->features |= NETIF_F_TSO6; |
| #ifdef BCM_VLAN |
| dev->features |= (NETIF_F_HW_VLAN_TX | NETIF_F_HW_VLAN_RX); |
| bp->flags |= (HW_VLAN_RX_FLAG | HW_VLAN_TX_FLAG); |
| |
| dev->vlan_features |= NETIF_F_SG; |
| dev->vlan_features |= NETIF_F_HW_CSUM; |
| if (bp->flags & USING_DAC_FLAG) |
| dev->vlan_features |= NETIF_F_HIGHDMA; |
| dev->vlan_features |= (NETIF_F_TSO | NETIF_F_TSO_ECN); |
| dev->vlan_features |= NETIF_F_TSO6; |
| #endif |
| |
| /* get_port_hwinfo() will set prtad and mmds properly */ |
| bp->mdio.prtad = MDIO_PRTAD_NONE; |
| bp->mdio.mmds = 0; |
| bp->mdio.mode_support = MDIO_SUPPORTS_C45 | MDIO_EMULATE_C22; |
| bp->mdio.dev = dev; |
| bp->mdio.mdio_read = bnx2x_mdio_read; |
| bp->mdio.mdio_write = bnx2x_mdio_write; |
| |
| return 0; |
| |
| err_out_unmap: |
| if (bp->regview) { |
| iounmap(bp->regview); |
| bp->regview = NULL; |
| } |
| if (bp->doorbells) { |
| iounmap(bp->doorbells); |
| bp->doorbells = NULL; |
| } |
| |
| err_out_release: |
| if (atomic_read(&pdev->enable_cnt) == 1) |
| pci_release_regions(pdev); |
| |
| err_out_disable: |
| pci_disable_device(pdev); |
| pci_set_drvdata(pdev, NULL); |
| |
| err_out: |
| return rc; |
| } |
| |
| static void __devinit bnx2x_get_pcie_width_speed(struct bnx2x *bp, |
| int *width, int *speed) |
| { |
| u32 val = REG_RD(bp, PCICFG_OFFSET + PCICFG_LINK_CONTROL); |
| |
| *width = (val & PCICFG_LINK_WIDTH) >> PCICFG_LINK_WIDTH_SHIFT; |
| |
| /* return value of 1=2.5GHz 2=5GHz */ |
| *speed = (val & PCICFG_LINK_SPEED) >> PCICFG_LINK_SPEED_SHIFT; |
| } |
| |
| static int bnx2x_check_firmware(struct bnx2x *bp) |
| { |
| const struct firmware *firmware = bp->firmware; |
| struct bnx2x_fw_file_hdr *fw_hdr; |
| struct bnx2x_fw_file_section *sections; |
| u32 offset, len, num_ops; |
| u16 *ops_offsets; |
| int i; |
| const u8 *fw_ver; |
| |
| if (firmware->size < sizeof(struct bnx2x_fw_file_hdr)) |
| return -EINVAL; |
| |
| fw_hdr = (struct bnx2x_fw_file_hdr *)firmware->data; |
| sections = (struct bnx2x_fw_file_section *)fw_hdr; |
| |
| /* Make sure none of the offsets and sizes make us read beyond |
| * the end of the firmware data */ |
| for (i = 0; i < sizeof(*fw_hdr) / sizeof(*sections); i++) { |
| offset = be32_to_cpu(sections[i].offset); |
| len = be32_to_cpu(sections[i].len); |
| if (offset + len > firmware->size) { |
| dev_err(&bp->pdev->dev, |
| "Section %d length is out of bounds\n", i); |
| return -EINVAL; |
| } |
| } |
| |
| /* Likewise for the init_ops offsets */ |
| offset = be32_to_cpu(fw_hdr->init_ops_offsets.offset); |
| ops_offsets = (u16 *)(firmware->data + offset); |
| num_ops = be32_to_cpu(fw_hdr->init_ops.len) / sizeof(struct raw_op); |
| |
| for (i = 0; i < be32_to_cpu(fw_hdr->init_ops_offsets.len) / 2; i++) { |
| if (be16_to_cpu(ops_offsets[i]) > num_ops) { |
| dev_err(&bp->pdev->dev, |
| "Section offset %d is out of bounds\n", i); |
| return -EINVAL; |
| } |
| } |
| |
| /* Check FW version */ |
| offset = be32_to_cpu(fw_hdr->fw_version.offset); |
| fw_ver = firmware->data + offset; |
| if ((fw_ver[0] != BCM_5710_FW_MAJOR_VERSION) || |
| (fw_ver[1] != BCM_5710_FW_MINOR_VERSION) || |
| (fw_ver[2] != BCM_5710_FW_REVISION_VERSION) || |
| (fw_ver[3] != BCM_5710_FW_ENGINEERING_VERSION)) { |
| dev_err(&bp->pdev->dev, |
| "Bad FW version:%d.%d.%d.%d. Should be %d.%d.%d.%d\n", |
| fw_ver[0], fw_ver[1], fw_ver[2], |
| fw_ver[3], BCM_5710_FW_MAJOR_VERSION, |
| BCM_5710_FW_MINOR_VERSION, |
| BCM_5710_FW_REVISION_VERSION, |
| BCM_5710_FW_ENGINEERING_VERSION); |
| return -EINVAL; |
| } |
| |
| return 0; |
| } |
| |
| static inline void be32_to_cpu_n(const u8 *_source, u8 *_target, u32 n) |
| { |
| const __be32 *source = (const __be32 *)_source; |
| u32 *target = (u32 *)_target; |
| u32 i; |
| |
| for (i = 0; i < n/4; i++) |
| target[i] = be32_to_cpu(source[i]); |
| } |
| |
| /* |
| Ops array is stored in the following format: |
| {op(8bit), offset(24bit, big endian), data(32bit, big endian)} |
| */ |
| static inline void bnx2x_prep_ops(const u8 *_source, u8 *_target, u32 n) |
| { |
| const __be32 *source = (const __be32 *)_source; |
| struct raw_op *target = (struct raw_op *)_target; |
| u32 i, j, tmp; |
| |
| for (i = 0, j = 0; i < n/8; i++, j += 2) { |
| tmp = be32_to_cpu(source[j]); |
| target[i].op = (tmp >> 24) & 0xff; |
| target[i].offset = tmp & 0xffffff; |
| target[i].raw_data = be32_to_cpu(source[j + 1]); |
| } |
| } |
| |
| static inline void be16_to_cpu_n(const u8 *_source, u8 *_target, u32 n) |
| { |
| const __be16 *source = (const __be16 *)_source; |
| u16 *target = (u16 *)_target; |
| u32 i; |
| |
| for (i = 0; i < n/2; i++) |
| target[i] = be16_to_cpu(source[i]); |
| } |
| |
| #define BNX2X_ALLOC_AND_SET(arr, lbl, func) \ |
| do { \ |
| u32 len = be32_to_cpu(fw_hdr->arr.len); \ |
| bp->arr = kmalloc(len, GFP_KERNEL); \ |
| if (!bp->arr) { \ |
| pr_err("Failed to allocate %d bytes for "#arr"\n", len); \ |
| goto lbl; \ |
| } \ |
| func(bp->firmware->data + be32_to_cpu(fw_hdr->arr.offset), \ |
| (u8 *)bp->arr, len); \ |
| } while (0) |
| |
| int bnx2x_init_firmware(struct bnx2x *bp) |
| { |
| const char *fw_file_name; |
| struct bnx2x_fw_file_hdr *fw_hdr; |
| int rc; |
| |
| if (CHIP_IS_E1(bp)) |
| fw_file_name = FW_FILE_NAME_E1; |
| else if (CHIP_IS_E1H(bp)) |
| fw_file_name = FW_FILE_NAME_E1H; |
| else { |
| BNX2X_ERR("Unsupported chip revision\n"); |
| return -EINVAL; |
| } |
| |
| BNX2X_DEV_INFO("Loading %s\n", fw_file_name); |
| |
| rc = request_firmware(&bp->firmware, fw_file_name, &bp->pdev->dev); |
| if (rc) { |
| BNX2X_ERR("Can't load firmware file %s\n", fw_file_name); |
| goto request_firmware_exit; |
| } |
| |
| rc = bnx2x_check_firmware(bp); |
| if (rc) { |
| BNX2X_ERR("Corrupt firmware file %s\n", fw_file_name); |
| goto request_firmware_exit; |
| } |
| |
| fw_hdr = (struct bnx2x_fw_file_hdr *)bp->firmware->data; |
| |
| /* Initialize the pointers to the init arrays */ |
| /* Blob */ |
| BNX2X_ALLOC_AND_SET(init_data, request_firmware_exit, be32_to_cpu_n); |
| |
| /* Opcodes */ |
| BNX2X_ALLOC_AND_SET(init_ops, init_ops_alloc_err, bnx2x_prep_ops); |
| |
| /* Offsets */ |
| BNX2X_ALLOC_AND_SET(init_ops_offsets, init_offsets_alloc_err, |
| be16_to_cpu_n); |
| |
| /* STORMs firmware */ |
| INIT_TSEM_INT_TABLE_DATA(bp) = bp->firmware->data + |
| be32_to_cpu(fw_hdr->tsem_int_table_data.offset); |
| INIT_TSEM_PRAM_DATA(bp) = bp->firmware->data + |
| be32_to_cpu(fw_hdr->tsem_pram_data.offset); |
| INIT_USEM_INT_TABLE_DATA(bp) = bp->firmware->data + |
| be32_to_cpu(fw_hdr->usem_int_table_data.offset); |
| INIT_USEM_PRAM_DATA(bp) = bp->firmware->data + |
| be32_to_cpu(fw_hdr->usem_pram_data.offset); |
| INIT_XSEM_INT_TABLE_DATA(bp) = bp->firmware->data + |
| be32_to_cpu(fw_hdr->xsem_int_table_data.offset); |
| INIT_XSEM_PRAM_DATA(bp) = bp->firmware->data + |
| be32_to_cpu(fw_hdr->xsem_pram_data.offset); |
| INIT_CSEM_INT_TABLE_DATA(bp) = bp->firmware->data + |
| be32_to_cpu(fw_hdr->csem_int_table_data.offset); |
| INIT_CSEM_PRAM_DATA(bp) = bp->firmware->data + |
| be32_to_cpu(fw_hdr->csem_pram_data.offset); |
| |
| return 0; |
| |
| init_offsets_alloc_err: |
| kfree(bp->init_ops); |
| init_ops_alloc_err: |
| kfree(bp->init_data); |
| request_firmware_exit: |
| release_firmware(bp->firmware); |
| |
| return rc; |
| } |
| |
| |
| static int __devinit bnx2x_init_one(struct pci_dev *pdev, |
| const struct pci_device_id *ent) |
| { |
| struct net_device *dev = NULL; |
| struct bnx2x *bp; |
| int pcie_width, pcie_speed; |
| int rc; |
| |
| /* dev zeroed in init_etherdev */ |
| dev = alloc_etherdev_mq(sizeof(*bp), MAX_CONTEXT); |
| if (!dev) { |
| dev_err(&pdev->dev, "Cannot allocate net device\n"); |
| return -ENOMEM; |
| } |
| |
| bp = netdev_priv(dev); |
| bp->msg_enable = debug; |
| |
| pci_set_drvdata(pdev, dev); |
| |
| rc = bnx2x_init_dev(pdev, dev); |
| if (rc < 0) { |
| free_netdev(dev); |
| return rc; |
| } |
| |
| rc = bnx2x_init_bp(bp); |
| if (rc) |
| goto init_one_exit; |
| |
| rc = register_netdev(dev); |
| if (rc) { |
| dev_err(&pdev->dev, "Cannot register net device\n"); |
| goto init_one_exit; |
| } |
| |
| bnx2x_get_pcie_width_speed(bp, &pcie_width, &pcie_speed); |
| netdev_info(dev, "%s (%c%d) PCI-E x%d %s found at mem %lx," |
| " IRQ %d, ", board_info[ent->driver_data].name, |
| (CHIP_REV(bp) >> 12) + 'A', (CHIP_METAL(bp) >> 4), |
| pcie_width, (pcie_speed == 2) ? "5GHz (Gen2)" : "2.5GHz", |
| dev->base_addr, bp->pdev->irq); |
| pr_cont("node addr %pM\n", dev->dev_addr); |
| |
| return 0; |
| |
| init_one_exit: |
| if (bp->regview) |
| iounmap(bp->regview); |
| |
| if (bp->doorbells) |
| iounmap(bp->doorbells); |
| |
| free_netdev(dev); |
| |
| if (atomic_read(&pdev->enable_cnt) == 1) |
| pci_release_regions(pdev); |
| |
| pci_disable_device(pdev); |
| pci_set_drvdata(pdev, NULL); |
| |
| return rc; |
| } |
| |
| static void __devexit bnx2x_remove_one(struct pci_dev *pdev) |
| { |
| struct net_device *dev = pci_get_drvdata(pdev); |
| struct bnx2x *bp; |
| |
| if (!dev) { |
| dev_err(&pdev->dev, "BAD net device from bnx2x_init_one\n"); |
| return; |
| } |
| bp = netdev_priv(dev); |
| |
| unregister_netdev(dev); |
| |
| /* Make sure RESET task is not scheduled before continuing */ |
| cancel_delayed_work_sync(&bp->reset_task); |
| |
| if (bp->regview) |
| iounmap(bp->regview); |
| |
| if (bp->doorbells) |
| iounmap(bp->doorbells); |
| |
| free_netdev(dev); |
| |
| if (atomic_read(&pdev->enable_cnt) == 1) |
| pci_release_regions(pdev); |
| |
| pci_disable_device(pdev); |
| pci_set_drvdata(pdev, NULL); |
| } |
| |
| static int bnx2x_eeh_nic_unload(struct bnx2x *bp) |
| { |
| int i; |
| |
| bp->state = BNX2X_STATE_ERROR; |
| |
| bp->rx_mode = BNX2X_RX_MODE_NONE; |
| |
| bnx2x_netif_stop(bp, 0); |
| netif_carrier_off(bp->dev); |
| |
| del_timer_sync(&bp->timer); |
| bp->stats_state = STATS_STATE_DISABLED; |
| DP(BNX2X_MSG_STATS, "stats_state - DISABLED\n"); |
| |
| /* Release IRQs */ |
| bnx2x_free_irq(bp, false); |
| |
| if (CHIP_IS_E1(bp)) { |
| struct mac_configuration_cmd *config = |
| bnx2x_sp(bp, mcast_config); |
| |
| for (i = 0; i < config->hdr.length; i++) |
| CAM_INVALIDATE(config->config_table[i]); |
| } |
| |
| /* Free SKBs, SGEs, TPA pool and driver internals */ |
| bnx2x_free_skbs(bp); |
| for_each_queue(bp, i) |
| bnx2x_free_rx_sge_range(bp, bp->fp + i, NUM_RX_SGE); |
| for_each_queue(bp, i) |
| netif_napi_del(&bnx2x_fp(bp, i, napi)); |
| bnx2x_free_mem(bp); |
| |
| bp->state = BNX2X_STATE_CLOSED; |
| |
| return 0; |
| } |
| |
| static void bnx2x_eeh_recover(struct bnx2x *bp) |
| { |
| u32 val; |
| |
| mutex_init(&bp->port.phy_mutex); |
| |
| bp->common.shmem_base = REG_RD(bp, MISC_REG_SHARED_MEM_ADDR); |
| bp->link_params.shmem_base = bp->common.shmem_base; |
| BNX2X_DEV_INFO("shmem offset is 0x%x\n", bp->common.shmem_base); |
| |
| if (!bp->common.shmem_base || |
| (bp->common.shmem_base < 0xA0000) || |
| (bp->common.shmem_base >= 0xC0000)) { |
| BNX2X_DEV_INFO("MCP not active\n"); |
| bp->flags |= NO_MCP_FLAG; |
| return; |
| } |
| |
| val = SHMEM_RD(bp, validity_map[BP_PORT(bp)]); |
| if ((val & (SHR_MEM_VALIDITY_DEV_INFO | SHR_MEM_VALIDITY_MB)) |
| != (SHR_MEM_VALIDITY_DEV_INFO | SHR_MEM_VALIDITY_MB)) |
| BNX2X_ERR("BAD MCP validity signature\n"); |
| |
| if (!BP_NOMCP(bp)) { |
| bp->fw_seq = (SHMEM_RD(bp, func_mb[BP_FUNC(bp)].drv_mb_header) |
| & DRV_MSG_SEQ_NUMBER_MASK); |
| BNX2X_DEV_INFO("fw_seq 0x%08x\n", bp->fw_seq); |
| } |
| } |
| |
| /** |
| * bnx2x_io_error_detected - called when PCI error is detected |
| * @pdev: Pointer to PCI device |
| * @state: The current pci connection state |
| * |
| * This function is called after a PCI bus error affecting |
| * this device has been detected. |
| */ |
| static pci_ers_result_t bnx2x_io_error_detected(struct pci_dev *pdev, |
| pci_channel_state_t state) |
| { |
| struct net_device *dev = pci_get_drvdata(pdev); |
| struct bnx2x *bp = netdev_priv(dev); |
| |
| rtnl_lock(); |
| |
| netif_device_detach(dev); |
| |
| if (state == pci_channel_io_perm_failure) { |
| rtnl_unlock(); |
| return PCI_ERS_RESULT_DISCONNECT; |
| } |
| |
| if (netif_running(dev)) |
| bnx2x_eeh_nic_unload(bp); |
| |
| pci_disable_device(pdev); |
| |
| rtnl_unlock(); |
| |
| /* Request a slot reset */ |
| return PCI_ERS_RESULT_NEED_RESET; |
| } |
| |
| /** |
| * bnx2x_io_slot_reset - called after the PCI bus has been reset |
| * @pdev: Pointer to PCI device |
| * |
| * Restart the card from scratch, as if from a cold-boot. |
| */ |
| static pci_ers_result_t bnx2x_io_slot_reset(struct pci_dev *pdev) |
| { |
| struct net_device *dev = pci_get_drvdata(pdev); |
| struct bnx2x *bp = netdev_priv(dev); |
| |
| rtnl_lock(); |
| |
| if (pci_enable_device(pdev)) { |
| dev_err(&pdev->dev, |
| "Cannot re-enable PCI device after reset\n"); |
| rtnl_unlock(); |
| return PCI_ERS_RESULT_DISCONNECT; |
| } |
| |
| pci_set_master(pdev); |
| pci_restore_state(pdev); |
| |
| if (netif_running(dev)) |
| bnx2x_set_power_state(bp, PCI_D0); |
| |
| rtnl_unlock(); |
| |
| return PCI_ERS_RESULT_RECOVERED; |
| } |
| |
| /** |
| * bnx2x_io_resume - called when traffic can start flowing again |
| * @pdev: Pointer to PCI device |
| * |
| * This callback is called when the error recovery driver tells us that |
| * its OK to resume normal operation. |
| */ |
| static void bnx2x_io_resume(struct pci_dev *pdev) |
| { |
| struct net_device *dev = pci_get_drvdata(pdev); |
| struct bnx2x *bp = netdev_priv(dev); |
| |
| if (bp->recovery_state != BNX2X_RECOVERY_DONE) { |
| printk(KERN_ERR "Handling parity error recovery. Try again later\n"); |
| return; |
| } |
| |
| rtnl_lock(); |
| |
| bnx2x_eeh_recover(bp); |
| |
| if (netif_running(dev)) |
| bnx2x_nic_load(bp, LOAD_NORMAL); |
| |
| netif_device_attach(dev); |
| |
| rtnl_unlock(); |
| } |
| |
| static struct pci_error_handlers bnx2x_err_handler = { |
| .error_detected = bnx2x_io_error_detected, |
| .slot_reset = bnx2x_io_slot_reset, |
| .resume = bnx2x_io_resume, |
| }; |
| |
| static struct pci_driver bnx2x_pci_driver = { |
| .name = DRV_MODULE_NAME, |
| .id_table = bnx2x_pci_tbl, |
| .probe = bnx2x_init_one, |
| .remove = __devexit_p(bnx2x_remove_one), |
| .suspend = bnx2x_suspend, |
| .resume = bnx2x_resume, |
| .err_handler = &bnx2x_err_handler, |
| }; |
| |
| static int __init bnx2x_init(void) |
| { |
| int ret; |
| |
| pr_info("%s", version); |
| |
| bnx2x_wq = create_singlethread_workqueue("bnx2x"); |
| if (bnx2x_wq == NULL) { |
| pr_err("Cannot create workqueue\n"); |
| return -ENOMEM; |
| } |
| |
| ret = pci_register_driver(&bnx2x_pci_driver); |
| if (ret) { |
| pr_err("Cannot register driver\n"); |
| destroy_workqueue(bnx2x_wq); |
| } |
| return ret; |
| } |
| |
| static void __exit bnx2x_cleanup(void) |
| { |
| pci_unregister_driver(&bnx2x_pci_driver); |
| |
| destroy_workqueue(bnx2x_wq); |
| } |
| |
| module_init(bnx2x_init); |
| module_exit(bnx2x_cleanup); |
| |
| #ifdef BCM_CNIC |
| |
| /* count denotes the number of new completions we have seen */ |
| static void bnx2x_cnic_sp_post(struct bnx2x *bp, int count) |
| { |
| struct eth_spe *spe; |
| |
| #ifdef BNX2X_STOP_ON_ERROR |
| if (unlikely(bp->panic)) |
| return; |
| #endif |
| |
| spin_lock_bh(&bp->spq_lock); |
| bp->cnic_spq_pending -= count; |
| |
| for (; bp->cnic_spq_pending < bp->cnic_eth_dev.max_kwqe_pending; |
| bp->cnic_spq_pending++) { |
| |
| if (!bp->cnic_kwq_pending) |
| break; |
| |
| spe = bnx2x_sp_get_next(bp); |
| *spe = *bp->cnic_kwq_cons; |
| |
| bp->cnic_kwq_pending--; |
| |
| DP(NETIF_MSG_TIMER, "pending on SPQ %d, on KWQ %d count %d\n", |
| bp->cnic_spq_pending, bp->cnic_kwq_pending, count); |
| |
| if (bp->cnic_kwq_cons == bp->cnic_kwq_last) |
| bp->cnic_kwq_cons = bp->cnic_kwq; |
| else |
| bp->cnic_kwq_cons++; |
| } |
| bnx2x_sp_prod_update(bp); |
| spin_unlock_bh(&bp->spq_lock); |
| } |
| |
| static int bnx2x_cnic_sp_queue(struct net_device *dev, |
| struct kwqe_16 *kwqes[], u32 count) |
| { |
| struct bnx2x *bp = netdev_priv(dev); |
| int i; |
| |
| #ifdef BNX2X_STOP_ON_ERROR |
| if (unlikely(bp->panic)) |
| return -EIO; |
| #endif |
| |
| spin_lock_bh(&bp->spq_lock); |
| |
| for (i = 0; i < count; i++) { |
| struct eth_spe *spe = (struct eth_spe *)kwqes[i]; |
| |
| if (bp->cnic_kwq_pending == MAX_SP_DESC_CNT) |
| break; |
| |
| *bp->cnic_kwq_prod = *spe; |
| |
| bp->cnic_kwq_pending++; |
| |
| DP(NETIF_MSG_TIMER, "L5 SPQE %x %x %x:%x pos %d\n", |
| spe->hdr.conn_and_cmd_data, spe->hdr.type, |
| spe->data.mac_config_addr.hi, |
| spe->data.mac_config_addr.lo, |
| bp->cnic_kwq_pending); |
| |
| if (bp->cnic_kwq_prod == bp->cnic_kwq_last) |
| bp->cnic_kwq_prod = bp->cnic_kwq; |
| else |
| bp->cnic_kwq_prod++; |
| } |
| |
| spin_unlock_bh(&bp->spq_lock); |
| |
| if (bp->cnic_spq_pending < bp->cnic_eth_dev.max_kwqe_pending) |
| bnx2x_cnic_sp_post(bp, 0); |
| |
| return i; |
| } |
| |
| static int bnx2x_cnic_ctl_send(struct bnx2x *bp, struct cnic_ctl_info *ctl) |
| { |
| struct cnic_ops *c_ops; |
| int rc = 0; |
| |
| mutex_lock(&bp->cnic_mutex); |
| c_ops = bp->cnic_ops; |
| if (c_ops) |
| rc = c_ops->cnic_ctl(bp->cnic_data, ctl); |
| mutex_unlock(&bp->cnic_mutex); |
| |
| return rc; |
| } |
| |
| static int bnx2x_cnic_ctl_send_bh(struct bnx2x *bp, struct cnic_ctl_info *ctl) |
| { |
| struct cnic_ops *c_ops; |
| int rc = 0; |
| |
| rcu_read_lock(); |
| c_ops = rcu_dereference(bp->cnic_ops); |
| if (c_ops) |
| rc = c_ops->cnic_ctl(bp->cnic_data, ctl); |
| rcu_read_unlock(); |
| |
| return rc; |
| } |
| |
| /* |
| * for commands that have no data |
| */ |
| int bnx2x_cnic_notify(struct bnx2x *bp, int cmd) |
| { |
| struct cnic_ctl_info ctl = {0}; |
| |
| ctl.cmd = cmd; |
| |
| return bnx2x_cnic_ctl_send(bp, &ctl); |
| } |
| |
| static void bnx2x_cnic_cfc_comp(struct bnx2x *bp, int cid) |
| { |
| struct cnic_ctl_info ctl; |
| |
| /* first we tell CNIC and only then we count this as a completion */ |
| ctl.cmd = CNIC_CTL_COMPLETION_CMD; |
| ctl.data.comp.cid = cid; |
| |
| bnx2x_cnic_ctl_send_bh(bp, &ctl); |
| bnx2x_cnic_sp_post(bp, 1); |
| } |
| |
| static int bnx2x_drv_ctl(struct net_device *dev, struct drv_ctl_info *ctl) |
| { |
| struct bnx2x *bp = netdev_priv(dev); |
| int rc = 0; |
| |
| switch (ctl->cmd) { |
| case DRV_CTL_CTXTBL_WR_CMD: { |
| u32 index = ctl->data.io.offset; |
| dma_addr_t addr = ctl->data.io.dma_addr; |
| |
| bnx2x_ilt_wr(bp, index, addr); |
| break; |
| } |
| |
| case DRV_CTL_COMPLETION_CMD: { |
| int count = ctl->data.comp.comp_count; |
| |
| bnx2x_cnic_sp_post(bp, count); |
| break; |
| } |
| |
| /* rtnl_lock is held. */ |
| case DRV_CTL_START_L2_CMD: { |
| u32 cli = ctl->data.ring.client_id; |
| |
| bp->rx_mode_cl_mask |= (1 << cli); |
| bnx2x_set_storm_rx_mode(bp); |
| break; |
| } |
| |
| /* rtnl_lock is held. */ |
| case DRV_CTL_STOP_L2_CMD: { |
| u32 cli = ctl->data.ring.client_id; |
| |
| bp->rx_mode_cl_mask &= ~(1 << cli); |
| bnx2x_set_storm_rx_mode(bp); |
| break; |
| } |
| |
| default: |
| BNX2X_ERR("unknown command %x\n", ctl->cmd); |
| rc = -EINVAL; |
| } |
| |
| return rc; |
| } |
| |
| void bnx2x_setup_cnic_irq_info(struct bnx2x *bp) |
| { |
| struct cnic_eth_dev *cp = &bp->cnic_eth_dev; |
| |
| if (bp->flags & USING_MSIX_FLAG) { |
| cp->drv_state |= CNIC_DRV_STATE_USING_MSIX; |
| cp->irq_arr[0].irq_flags |= CNIC_IRQ_FL_MSIX; |
| cp->irq_arr[0].vector = bp->msix_table[1].vector; |
| } else { |
| cp->drv_state &= ~CNIC_DRV_STATE_USING_MSIX; |
| cp->irq_arr[0].irq_flags &= ~CNIC_IRQ_FL_MSIX; |
| } |
| cp->irq_arr[0].status_blk = bp->cnic_sb; |
| cp->irq_arr[0].status_blk_num = CNIC_SB_ID(bp); |
| cp->irq_arr[1].status_blk = bp->def_status_blk; |
| cp->irq_arr[1].status_blk_num = DEF_SB_ID; |
| |
| cp->num_irq = 2; |
| } |
| |
| static int bnx2x_register_cnic(struct net_device *dev, struct cnic_ops *ops, |
| void *data) |
| { |
| struct bnx2x *bp = netdev_priv(dev); |
| struct cnic_eth_dev *cp = &bp->cnic_eth_dev; |
| |
| if (ops == NULL) |
| return -EINVAL; |
| |
| if (atomic_read(&bp->intr_sem) != 0) |
| return -EBUSY; |
| |
| bp->cnic_kwq = kzalloc(PAGE_SIZE, GFP_KERNEL); |
| if (!bp->cnic_kwq) |
| return -ENOMEM; |
| |
| bp->cnic_kwq_cons = bp->cnic_kwq; |
| bp->cnic_kwq_prod = bp->cnic_kwq; |
| bp->cnic_kwq_last = bp->cnic_kwq + MAX_SP_DESC_CNT; |
| |
| bp->cnic_spq_pending = 0; |
| bp->cnic_kwq_pending = 0; |
| |
| bp->cnic_data = data; |
| |
| cp->num_irq = 0; |
| cp->drv_state = CNIC_DRV_STATE_REGD; |
| |
| bnx2x_init_sb(bp, bp->cnic_sb, bp->cnic_sb_mapping, CNIC_SB_ID(bp)); |
| |
| bnx2x_setup_cnic_irq_info(bp); |
| bnx2x_set_iscsi_eth_mac_addr(bp, 1); |
| bp->cnic_flags |= BNX2X_CNIC_FLAG_MAC_SET; |
| rcu_assign_pointer(bp->cnic_ops, ops); |
| |
| return 0; |
| } |
| |
| static int bnx2x_unregister_cnic(struct net_device *dev) |
| { |
| struct bnx2x *bp = netdev_priv(dev); |
| struct cnic_eth_dev *cp = &bp->cnic_eth_dev; |
| |
| mutex_lock(&bp->cnic_mutex); |
| if (bp->cnic_flags & BNX2X_CNIC_FLAG_MAC_SET) { |
| bp->cnic_flags &= ~BNX2X_CNIC_FLAG_MAC_SET; |
| bnx2x_set_iscsi_eth_mac_addr(bp, 0); |
| } |
| cp->drv_state = 0; |
| rcu_assign_pointer(bp->cnic_ops, NULL); |
| mutex_unlock(&bp->cnic_mutex); |
| synchronize_rcu(); |
| kfree(bp->cnic_kwq); |
| bp->cnic_kwq = NULL; |
| |
| return 0; |
| } |
| |
| struct cnic_eth_dev *bnx2x_cnic_probe(struct net_device *dev) |
| { |
| struct bnx2x *bp = netdev_priv(dev); |
| struct cnic_eth_dev *cp = &bp->cnic_eth_dev; |
| |
| cp->drv_owner = THIS_MODULE; |
| cp->chip_id = CHIP_ID(bp); |
| cp->pdev = bp->pdev; |
| cp->io_base = bp->regview; |
| cp->io_base2 = bp->doorbells; |
| cp->max_kwqe_pending = 8; |
| cp->ctx_blk_size = CNIC_CTX_PER_ILT * sizeof(union cdu_context); |
| cp->ctx_tbl_offset = FUNC_ILT_BASE(BP_FUNC(bp)) + 1; |
| cp->ctx_tbl_len = CNIC_ILT_LINES; |
| cp->starting_cid = BCM_CNIC_CID_START; |
| cp->drv_submit_kwqes_16 = bnx2x_cnic_sp_queue; |
| cp->drv_ctl = bnx2x_drv_ctl; |
| cp->drv_register_cnic = bnx2x_register_cnic; |
| cp->drv_unregister_cnic = bnx2x_unregister_cnic; |
| |
| return cp; |
| } |
| EXPORT_SYMBOL(bnx2x_cnic_probe); |
| |
| #endif /* BCM_CNIC */ |
| |