| #ifndef __ASM_SH_RENESAS_R7780RP_H |
| #define __ASM_SH_RENESAS_R7780RP_H |
| |
| /* |
| * linux/include/asm-sh/r7780rp.h |
| * |
| * Copyright (C) 2000 Atom Create Engineering Co., Ltd. |
| * |
| * Renesas Solutions Highlander R7780RP support |
| */ |
| |
| /* Box specific addresses. */ |
| #if defined(CONFIG_SH_R7780MP) |
| #define PA_BCR 0xa4000000 /* FPGA */ |
| #define PA_IRLMSK (PA_BCR+0x0000) /* Interrupt Mask control */ |
| #define PA_IRLMON (PA_BCR+0x0002) /* Interrupt Status control */ |
| #define PA_IRLPRI1 (PA_BCR+0x0004) /* Interrupt Priorty 1 */ |
| #define PA_IRLPRI2 (PA_BCR+0x0006) /* Interrupt Priorty 2 */ |
| #define PA_IRLPRI3 (PA_BCR+0x0008) /* Interrupt Priorty 3 */ |
| #define PA_IRLPRI4 (PA_BCR+0x000a) /* Interrupt Priorty 4 */ |
| #define PA_RSTCTL (PA_BCR+0x000c) /* Reset Control */ |
| #define PA_PCIBD (PA_BCR+0x000e) /* PCI Board detect control */ |
| #define PA_PCICD (PA_BCR+0x0010) /* PCI Conector detect control */ |
| #define PA_EXTGIO (PA_BCR+0x0016) /* Extension GPIO Control */ |
| #define PA_IVDRMON (PA_BCR+0x0018) /* iVDR Moniter control */ |
| #define PA_IVDRCTL (PA_BCR+0x001a) /* iVDR control */ |
| #define PA_OBLED (PA_BCR+0x001c) /* On Board LED control */ |
| #define PA_OBSW (PA_BCR+0x001e) /* On Board Switch control */ |
| #define PA_AUDIOSEL (PA_BCR+0x0020) /* Sound Interface Select control */ |
| #define PA_EXTPLR (PA_BCR+0x001e) /* Extention Pin Polarity control */ |
| #define PA_TPCTL (PA_BCR+0x0100) /* Touch Panel Access control */ |
| #define PA_TPDCKCTL (PA_BCR+0x0102) /* Touch Panel Access data control */ |
| #define PA_TPCTLCLR (PA_BCR+0x0104) /* Touch Panel Access control */ |
| #define PA_TPXPOS (PA_BCR+0x0106) /* Touch Panel X position control */ |
| #define PA_TPYPOS (PA_BCR+0x0108) /* Touch Panel Y position control */ |
| #define PA_DBSW (PA_BCR+0x0200) /* Debug Board Switch control */ |
| #define PA_CFCTL (PA_BCR+0x0300) /* CF Timing control */ |
| #define PA_CFPOW (PA_BCR+0x0302) /* CF Power control */ |
| #define PA_CFCDINTCLR (PA_BCR+0x0304) /* CF Insert Interrupt clear */ |
| #define PA_SCSMR0 (PA_BCR+0x0400) /* SCIF0 Serial mode control */ |
| #define PA_SCBRR0 (PA_BCR+0x0404) /* SCIF0 Bit rate control */ |
| #define PA_SCSCR0 (PA_BCR+0x0408) /* SCIF0 Serial control */ |
| #define PA_SCFTDR0 (PA_BCR+0x040c) /* SCIF0 Send FIFO control */ |
| #define PA_SCFSR0 (PA_BCR+0x0410) /* SCIF0 Serial status control */ |
| #define PA_SCFRDR0 (PA_BCR+0x0414) /* SCIF0 Receive FIFO control */ |
| #define PA_SCFCR0 (PA_BCR+0x0418) /* SCIF0 FIFO control */ |
| #define PA_SCTFDR0 (PA_BCR+0x041c) /* SCIF0 Send FIFO data control */ |
| #define PA_SCRFDR0 (PA_BCR+0x0420) /* SCIF0 Receive FIFO data control */ |
| #define PA_SCSPTR0 (PA_BCR+0x0424) /* SCIF0 Serial Port control */ |
| #define PA_SCLSR0 (PA_BCR+0x0428) /* SCIF0 Line Status control */ |
| #define PA_SCRER0 (PA_BCR+0x042c) /* SCIF0 Serial Error control */ |
| #define PA_SCSMR1 (PA_BCR+0x0500) /* SCIF1 Serial mode control */ |
| #define PA_SCBRR1 (PA_BCR+0x0504) /* SCIF1 Bit rate control */ |
| #define PA_SCSCR1 (PA_BCR+0x0508) /* SCIF1 Serial control */ |
| #define PA_SCFTDR1 (PA_BCR+0x050c) /* SCIF1 Send FIFO control */ |
| #define PA_SCFSR1 (PA_BCR+0x0510) /* SCIF1 Serial status control */ |
| #define PA_SCFRDR1 (PA_BCR+0x0514) /* SCIF1 Receive FIFO control */ |
| #define PA_SCFCR1 (PA_BCR+0x0518) /* SCIF1 FIFO control */ |
| #define PA_SCTFDR1 (PA_BCR+0x051c) /* SCIF1 Send FIFO data control */ |
| #define PA_SCRFDR1 (PA_BCR+0x0520) /* SCIF1 Receive FIFO data control */ |
| #define PA_SCSPTR1 (PA_BCR+0x0524) /* SCIF1 Serial Port control */ |
| #define PA_SCLSR1 (PA_BCR+0x0528) /* SCIF1 Line Status control */ |
| #define PA_SCRER1 (PA_BCR+0x052c) /* SCIF1 Serial Error control */ |
| #define PA_ICCR (PA_BCR+0x0600) /* Serial control */ |
| #define PA_SAR (PA_BCR+0x0602) /* Serial Slave control */ |
| #define PA_MDR (PA_BCR+0x0604) /* Serial Mode control */ |
| #define PA_ADR1 (PA_BCR+0x0606) /* Serial Address1 control */ |
| #define PA_DAR1 (PA_BCR+0x0646) /* Serial Data1 control */ |
| #define PA_VERREG (PA_BCR+0x0700) /* FPGA Version Register */ |
| #define PA_POFF (PA_BCR+0x0800) /* System Power Off control */ |
| #define PA_PMR (PA_BCR+0x0900) /* */ |
| |
| #define PA_AX88796L 0xa4100400 /* AX88796L Area */ |
| #define PA_SC1602BSLB 0xa6000000 /* SC1602BSLB Area */ |
| #define PA_AREA5_IO 0xb4000000 /* Area 5 IO Memory */ |
| #define PA_AREA6_IO 0xb8000000 /* Area 6 IO Memory */ |
| #define PA_IDE_OFFSET 0x1f0 /* CF IDE Offset */ |
| #define AX88796L_IO_BASE 0x1000 /* AX88796L IO Base Address */ |
| |
| #define IRLCNTR1 (PA_BCR + 0) /* Interrupt Control Register1 */ |
| |
| #define IRQ_PCISLOT1 65 /* PCI Slot #1 IRQ */ |
| #define IRQ_PCISLOT2 66 /* PCI Slot #2 IRQ */ |
| #define IRQ_PCISLOT3 67 /* PCI Slot #3 IRQ */ |
| #define IRQ_PCISLOT4 68 /* PCI Slot #4 IRQ */ |
| #define IRQ_CFCARD 1 /* CF Card IRQ */ |
| // #define IRQ_CFINST 0 /* CF Card Insert IRQ */ |
| #define IRQ_TP 2 /* Touch Panel IRQ */ |
| #define IRQ_SCI1 3 /* SCI1 IRQ */ |
| #define IRQ_SCI0 4 /* SCI0 IRQ */ |
| #define IRQ_2SERIAL 5 /* Serial IRQ */ |
| #define IRQ_RTC 6 /* RTC A / B IRQ */ |
| #define IRQ_EXTENTION6 7 /* EXT6n IRQ */ |
| #define IRQ_EXTENTION5 8 /* EXT5n IRQ */ |
| #define IRQ_EXTENTION4 9 /* EXT4n IRQ */ |
| #define IRQ_EXTENTION2 10 /* EXT2n IRQ */ |
| #define IRQ_EXTENTION1 11 /* EXT1n IRQ */ |
| #define IRQ_ONETH 13 /* On board Ethernet IRQ */ |
| #define IRQ_PSW 14 /* Push Switch IRQ */ |
| |
| #else /* R7780RP */ |
| |
| #define PA_BCR 0xa5000000 /* FPGA */ |
| #define PA_IRLMSK (PA_BCR+0x0000) /* Interrupt Mask control */ |
| #define PA_IRLMON (PA_BCR+0x0002) /* Interrupt Status control */ |
| #define PA_SDPOW (PA_BCR+0x0004) /* SD Power control */ |
| #define PA_RSTCTL (PA_BCR+0x0006) /* Device Reset control */ |
| #define PA_PCIBD (PA_BCR+0x0008) /* PCI Board detect control */ |
| #define PA_PCICD (PA_BCR+0x000a) /* PCI Conector detect control */ |
| #define PA_ZIGIO1 (PA_BCR+0x000c) /* Zigbee IO control 1 */ |
| #define PA_ZIGIO2 (PA_BCR+0x000e) /* Zigbee IO control 2 */ |
| #define PA_ZIGIO3 (PA_BCR+0x0010) /* Zigbee IO control 3 */ |
| #define PA_ZIGIO4 (PA_BCR+0x0012) /* Zigbee IO control 4 */ |
| #define PA_IVDRMON (PA_BCR+0x0014) /* iVDR Moniter control */ |
| #define PA_IVDRCTL (PA_BCR+0x0016) /* iVDR control */ |
| #define PA_OBLED (PA_BCR+0x0018) /* On Board LED control */ |
| #define PA_OBSW (PA_BCR+0x001a) /* On Board Switch control */ |
| #define PA_AUDIOSEL (PA_BCR+0x001c) /* Sound Interface Select control */ |
| #define PA_EXTPLR (PA_BCR+0x001e) /* Extention Pin Polarity control */ |
| #define PA_TPCTL (PA_BCR+0x0100) /* Touch Panel Access control */ |
| #define PA_TPDCKCTL (PA_BCR+0x0102) /* Touch Panel Access data control */ |
| #define PA_TPCTLCLR (PA_BCR+0x0104) /* Touch Panel Access control */ |
| #define PA_TPXPOS (PA_BCR+0x0106) /* Touch Panel X position control */ |
| #define PA_TPYPOS (PA_BCR+0x0108) /* Touch Panel Y position control */ |
| #define PA_DBDET (PA_BCR+0x0200) /* Debug Board detect control */ |
| #define PA_DBDISPCTL (PA_BCR+0x0202) /* Debug Board Dot timing control */ |
| #define PA_DBSW (PA_BCR+0x0204) /* Debug Board Switch control */ |
| #define PA_CFCTL (PA_BCR+0x0300) /* CF Timing control */ |
| #define PA_CFPOW (PA_BCR+0x0302) /* CF Power control */ |
| #define PA_CFCDINTCLR (PA_BCR+0x0304) /* CF Insert Interrupt clear */ |
| #define PA_SCSMR (PA_BCR+0x0400) /* SCIF Serial mode control */ |
| #define PA_SCBRR (PA_BCR+0x0402) /* SCIF Bit rate control */ |
| #define PA_SCSCR (PA_BCR+0x0404) /* SCIF Serial control */ |
| #define PA_SCFDTR (PA_BCR+0x0406) /* SCIF Send FIFO control */ |
| #define PA_SCFSR (PA_BCR+0x0408) /* SCIF Serial status control */ |
| #define PA_SCFRDR (PA_BCR+0x040a) /* SCIF Receive FIFO control */ |
| #define PA_SCFCR (PA_BCR+0x040c) /* SCIF FIFO control */ |
| #define PA_SCFDR (PA_BCR+0x040e) /* SCIF FIFO data control */ |
| #define PA_SCLSR (PA_BCR+0x0412) /* SCIF Line Status control */ |
| #define PA_ICCR (PA_BCR+0x0500) /* Serial control */ |
| #define PA_SAR (PA_BCR+0x0502) /* Serial Slave control */ |
| #define PA_MDR (PA_BCR+0x0504) /* Serial Mode control */ |
| #define PA_ADR1 (PA_BCR+0x0506) /* Serial Address1 control */ |
| #define PA_DAR1 (PA_BCR+0x0546) /* Serial Data1 control */ |
| #define PA_VERREG (PA_BCR+0x0600) /* FPGA Version Register */ |
| |
| #define PA_AX88796L 0xa5800400 /* AX88796L Area */ |
| #define PA_SC1602BSLB 0xa6000000 /* SC1602BSLB Area */ |
| #define PA_AREA5_IO 0xb4000000 /* Area 5 IO Memory */ |
| #define PA_AREA6_IO 0xb8000000 /* Area 6 IO Memory */ |
| #define PA_IDE_OFFSET 0x1f0 /* CF IDE Offset */ |
| #define AX88796L_IO_BASE 0x1000 /* AX88796L IO Base Address */ |
| |
| #define IRLCNTR1 (PA_BCR + 0) /* Interrupt Control Register1 */ |
| |
| #define IRQ_PCISLOT1 0 /* PCI Slot #1 IRQ */ |
| #define IRQ_PCISLOT2 1 /* PCI Slot #2 IRQ */ |
| #define IRQ_PCISLOT3 2 /* PCI Slot #3 IRQ */ |
| #define IRQ_PCISLOT4 3 /* PCI Slot #4 IRQ */ |
| #define IRQ_CFCARD 4 /* CF Card IRQ */ |
| #define IRQ_CFINST 5 /* CF Card Insert IRQ */ |
| #define IRQ_M66596 6 /* M66596 IRQ */ |
| #define IRQ_SDCARD 7 /* SD Card IRQ */ |
| #define IRQ_TUCHPANEL 8 /* Touch Panel IRQ */ |
| #define IRQ_SCI 9 /* SCI IRQ */ |
| #define IRQ_2SERIAL 10 /* Serial IRQ */ |
| #define IRQ_EXTENTION 11 /* EXTn IRQ */ |
| #define IRQ_ONETH 12 /* On board Ethernet IRQ */ |
| #define IRQ_PSW 13 /* Push Switch IRQ */ |
| #define IRQ_ZIGBEE 14 /* Ziggbee IO IRQ */ |
| |
| #endif /* CONFIG_SH_R7780MP */ |
| |
| #define __IO_PREFIX r7780rp |
| #include <asm/io_generic.h> |
| |
| #endif /* __ASM_SH_RENESAS_R7780RP */ |