| config B43LEGACY |
| tristate "Broadcom 43xx-legacy wireless support (mac80211 stack)" |
| depends on SSB_POSSIBLE && MAC80211 && WLAN_80211 && HAS_DMA |
| select SSB |
| select FW_LOADER |
| select HW_RANDOM |
| ---help--- |
| b43legacy is a driver for 802.11b devices from Broadcom (BCM4301 and |
| BCM4303) and early model 802.11g chips (BCM4306 Ver. 2) used in the |
| Linksys WPC54G V1 PCMCIA devices. |
| |
| Newer 802.11g and 802.11a devices need b43. |
| |
| It is safe to include both b43 and b43legacy as the underlying glue |
| layer will automatically load the correct version for your device. |
| |
| This driver uses V3 firmware, which must be installed separately using |
| b43-fwcutter. |
| |
| This driver can be built as a module (recommended) that will be |
| called "b43legacy". If unsure, say M. |
| |
| # Auto-select SSB PCI-HOST support, if possible |
| config B43LEGACY_PCI_AUTOSELECT |
| bool |
| depends on B43LEGACY && SSB_PCIHOST_POSSIBLE |
| select SSB_PCIHOST |
| select SSB_B43_PCI_BRIDGE |
| default y |
| |
| # Auto-select SSB PCICORE driver, if possible |
| config B43LEGACY_PCICORE_AUTOSELECT |
| bool |
| depends on B43LEGACY && SSB_DRIVER_PCICORE_POSSIBLE |
| select SSB_DRIVER_PCICORE |
| default y |
| |
| # LED support |
| # This config option automatically enables b43legacy LEDS support, |
| # if it's possible. |
| config B43LEGACY_LEDS |
| bool |
| depends on B43LEGACY && MAC80211_LEDS && (LEDS_CLASS = y || LEDS_CLASS = B43LEGACY) |
| default y |
| |
| # RFKILL support |
| # This config option automatically enables b43legacy RFKILL support, |
| # if it's possible. |
| config B43LEGACY_RFKILL |
| bool |
| depends on B43LEGACY && (RFKILL = y || RFKILL = B43LEGACY) && RFKILL_INPUT && (INPUT_POLLDEV = y || INPUT_POLLDEV = B43LEGACY) |
| default y |
| |
| config B43LEGACY_DEBUG |
| bool "Broadcom 43xx-legacy debugging" |
| depends on B43LEGACY |
| default y |
| ---help--- |
| Say Y, because this information will help you get the driver running. |
| This option generates a minimum of log output. |
| |
| config B43LEGACY_DMA |
| bool |
| depends on B43LEGACY |
| |
| config B43LEGACY_PIO |
| bool |
| depends on B43LEGACY |
| |
| choice |
| prompt "Broadcom 43xx-legacy data transfer mode" |
| depends on B43LEGACY |
| default B43LEGACY_DMA_AND_PIO_MODE |
| |
| config B43LEGACY_DMA_AND_PIO_MODE |
| bool "DMA + PIO" |
| select B43LEGACY_DMA |
| select B43LEGACY_PIO |
| ---help--- |
| Include both, Direct Memory Access (DMA) and Programmed I/O (PIO) |
| data transfer modes. The mode actually used is selectable through |
| the module parameter "pio". With pio=0 as a module parameter, the |
| default DMA is used, otherwise PIO is used. |
| |
| If unsure, choose this option. |
| |
| config B43LEGACY_DMA_MODE |
| bool "DMA (Direct Memory Access) only" |
| select B43LEGACY_DMA |
| ---help--- |
| Only include Direct Memory Access (DMA). |
| This reduces the size of the driver module, by omitting the PIO code. |
| |
| config B43LEGACY_PIO_MODE |
| bool "PIO (Programmed I/O) only" |
| select B43LEGACY_PIO |
| ---help--- |
| Only include Programmed I/O (PIO). |
| This reduces the size of the driver module, by omitting the DMA code. |
| Please note that PIO transfers are slow (compared to DMA). |
| |
| Also note that not all devices of the b43legacy series support PIO. |
| |
| You should use PIO only if DMA does not work for you. |
| |
| endchoice |