| /* $Id: dram_init.S,v 1.4 2003/09/22 09:21:59 starvik Exp $ |
| * |
| * DRAM/SDRAM initialization - alter with care |
| * This file is intended to be included from other assembler files |
| * |
| * Note: This file may not modify r9 because r9 is used to carry |
| * information from the decompresser to the kernel |
| * |
| * Copyright (C) 2000, 2001 Axis Communications AB |
| * |
| * Authors: Mikael Starvik (starvik@axis.com) |
| * |
| * $Log: dram_init.S,v $ |
| * Revision 1.4 2003/09/22 09:21:59 starvik |
| * Decompresser is linked to 0x407xxxxx and sdram commands are at 0x000xxxxx |
| * so we need to mask off 12 bits. |
| * |
| * Revision 1.3 2003/03/31 09:38:37 starvik |
| * Corrected calculation of end of sdram init commands |
| * |
| * Revision 1.2 2002/11/19 13:33:29 starvik |
| * Changes from Linux 2.4 |
| * |
| * Revision 1.13 2002/10/30 07:42:28 starvik |
| * Always read SDRAM command sequence from flash |
| * |
| * Revision 1.12 2002/08/09 11:37:37 orjanf |
| * Added double initialization work-around for Samsung SDRAMs. |
| * |
| * Revision 1.11 2002/06/04 11:43:21 starvik |
| * Check if mrs_data is specified in kernelconfig (necessary for MCM) |
| * |
| * Revision 1.10 2001/10/04 12:00:21 martinnn |
| * Added missing underscores. |
| * |
| * Revision 1.9 2001/10/01 14:47:35 bjornw |
| * Added register prefixes and removed underscores |
| * |
| * Revision 1.8 2001/05/15 07:12:45 hp |
| * Copy warning from head.S about r8 and r9 |
| * |
| * Revision 1.7 2001/04/18 12:05:39 bjornw |
| * Fixed comments, and explicitely include config.h to be sure its there |
| * |
| * Revision 1.6 2001/04/10 06:20:16 starvik |
| * Delay should be 200us, not 200ns |
| * |
| * Revision 1.5 2001/04/09 06:01:13 starvik |
| * Added support for 100 MHz SDRAMs |
| * |
| * Revision 1.4 2001/03/26 14:24:01 bjornw |
| * Namechange of some config options |
| * |
| * Revision 1.3 2001/03/23 08:29:41 starvik |
| * Corrected calculation of mrs_data |
| * |
| * Revision 1.2 2001/02/08 15:20:00 starvik |
| * Corrected SDRAM initialization |
| * Should now be included as inline |
| * |
| * Revision 1.1 2001/01/29 13:08:02 starvik |
| * Initial version |
| * This file should be included from all assembler files that needs to |
| * initialize DRAM/SDRAM. |
| * |
| */ |
| |
| /* Just to be certain the config file is included, we include it here |
| * explicitely instead of depending on it being included in the file that |
| * uses this code. |
| */ |
| |
| #include <linux/config.h> |
| |
| ;; WARNING! The registers r8 and r9 are used as parameters carrying |
| ;; information from the decompressor (if the kernel was compressed). |
| ;; They should not be used in the code below. |
| |
| #ifndef CONFIG_SVINTO_SIM |
| move.d CONFIG_ETRAX_DEF_R_WAITSTATES, $r0 |
| move.d $r0, [R_WAITSTATES] |
| |
| move.d CONFIG_ETRAX_DEF_R_BUS_CONFIG, $r0 |
| move.d $r0, [R_BUS_CONFIG] |
| |
| #ifndef CONFIG_ETRAX_SDRAM |
| move.d CONFIG_ETRAX_DEF_R_DRAM_CONFIG, $r0 |
| move.d $r0, [R_DRAM_CONFIG] |
| |
| move.d CONFIG_ETRAX_DEF_R_DRAM_TIMING, $r0 |
| move.d $r0, [R_DRAM_TIMING] |
| #else |
| ;; Samsung SDRAMs seem to require to be initialized twice to work properly. |
| moveq 2, $r6 |
| _sdram_init: |
| |
| ; Refer to ETRAX 100LX Designers Reference for a description of SDRAM initialization |
| |
| ; Bank configuration |
| move.d CONFIG_ETRAX_DEF_R_SDRAM_CONFIG, $r0 |
| move.d $r0, [R_SDRAM_CONFIG] |
| |
| ; Calculate value of mrs_data |
| ; CAS latency = 2 && bus_width = 32 => 0x40 |
| ; CAS latency = 3 && bus_width = 32 => 0x60 |
| ; CAS latency = 2 && bus_width = 16 => 0x20 |
| ; CAS latency = 3 && bus_width = 16 => 0x30 |
| |
| ; Check if value is already supplied in kernel config |
| move.d CONFIG_ETRAX_DEF_R_SDRAM_TIMING, $r2 |
| and.d 0x00ff0000, $r2 |
| bne _set_timing |
| lsrq 16, $r2 |
| |
| move.d 0x40, $r2 ; Assume 32 bits and CAS latency = 2 |
| move.d CONFIG_ETRAX_DEF_R_SDRAM_TIMING, $r1 |
| move.d $r1, $r3 |
| and.d 0x03, $r1 ; Get CAS latency |
| and.d 0x1000, $r3 ; 50 or 100 MHz? |
| beq _speed_50 |
| nop |
| _speed_100: |
| cmp.d 0x00, $r1 ; CAS latency = 2? |
| beq _bw_check |
| nop |
| or.d 0x20, $r2 ; CAS latency = 3 |
| ba _bw_check |
| nop |
| _speed_50: |
| cmp.d 0x01, $r1 ; CAS latency = 2? |
| beq _bw_check |
| nop |
| or.d 0x20, $r2 ; CAS latency = 3 |
| _bw_check: |
| move.d CONFIG_ETRAX_DEF_R_SDRAM_CONFIG, $r1 |
| and.d 0x800000, $r1 ; DRAM width is bit 23 |
| bne _set_timing |
| nop |
| lsrq 1, $r2 ; 16 bits. Shift down value. |
| |
| ; Set timing parameters. Starts master clock |
| _set_timing: |
| move.d CONFIG_ETRAX_DEF_R_SDRAM_TIMING, $r1 |
| and.d 0x8000f9ff, $r1 ; Make sure mrs data and command is 0 |
| or.d 0x80000000, $r1 ; Make sure sdram enable bit is set |
| move.d $r1, $r5 |
| or.d 0x0000c000, $r1 ; ref = disable |
| lslq 16, $r2 ; mrs data starts at bit 16 |
| or.d $r2, $r1 |
| move.d $r1, [R_SDRAM_TIMING] |
| |
| ; Wait 200us |
| move.d 10000, $r2 |
| 1: bne 1b |
| subq 1, $r2 |
| |
| ; Issue initialization command sequence |
| move.d _sdram_commands_start, $r2 |
| and.d 0x000fffff, $r2 ; Make sure commands are read from flash |
| move.d _sdram_commands_end, $r3 |
| and.d 0x000fffff, $r3 |
| 1: clear.d $r4 |
| move.b [$r2+], $r4 |
| lslq 9, $r4 ; Command starts at bit 9 |
| or.d $r1, $r4 |
| move.d $r4, [R_SDRAM_TIMING] |
| nop ; Wait five nop cycles between each command |
| nop |
| nop |
| nop |
| nop |
| cmp.d $r2, $r3 |
| bne 1b |
| nop |
| move.d $r5, [R_SDRAM_TIMING] |
| subq 1, $r6 |
| bne _sdram_init |
| nop |
| ba _sdram_commands_end |
| nop |
| |
| _sdram_commands_start: |
| .byte 3 ; Precharge |
| .byte 0 ; nop |
| .byte 2 ; refresh |
| .byte 0 ; nop |
| .byte 2 ; refresh |
| .byte 0 ; nop |
| .byte 2 ; refresh |
| .byte 0 ; nop |
| .byte 2 ; refresh |
| .byte 0 ; nop |
| .byte 2 ; refresh |
| .byte 0 ; nop |
| .byte 2 ; refresh |
| .byte 0 ; nop |
| .byte 2 ; refresh |
| .byte 0 ; nop |
| .byte 2 ; refresh |
| .byte 0 ; nop |
| .byte 1 ; mrs |
| .byte 0 ; nop |
| _sdram_commands_end: |
| #endif |
| #endif |