| /* |
| * Blackfin cache control code |
| * |
| * Copyright 2004-2008 Analog Devices Inc. |
| * |
| * Enter bugs at http://blackfin.uclinux.org/ |
| * |
| * Licensed under the GPL-2 or later. |
| */ |
| |
| #include <linux/linkage.h> |
| #include <asm/blackfin.h> |
| #include <asm/cache.h> |
| #include <asm/page.h> |
| |
| .text |
| |
| /* Since all L1 caches work the same way, we use the same method for flushing |
| * them. Only the actual flush instruction differs. We write this in asm as |
| * GCC can be hard to coax into writing nice hardware loops. |
| * |
| * Also, we assume the following register setup: |
| * R0 = start address |
| * R1 = end address |
| */ |
| .macro do_flush flushins:req optflushins optnopins label |
| |
| /* end = ((end - 1) & -L1_CACHE_BYTES) + L1_CACHE_BYTES; */ |
| R1 += -1; |
| R2 = -L1_CACHE_BYTES; |
| R1 = R1 & R2; |
| R1 += L1_CACHE_BYTES; |
| |
| /* count = (end - start) >> L1_CACHE_SHIFT */ |
| R2 = R1 - R0; |
| R2 >>= L1_CACHE_SHIFT; |
| P1 = R2; |
| |
| .ifnb \label |
| \label : |
| .endif |
| P0 = R0; |
| LSETUP (1f, 2f) LC1 = P1; |
| 1: |
| .ifnb \optflushins |
| \optflushins [P0]; |
| .endif |
| .ifb \optnopins |
| 2: |
| .endif |
| \flushins [P0++]; |
| .ifnb \optnopins |
| 2: \optnopins; |
| .endif |
| |
| RTS; |
| .endm |
| |
| /* Invalidate all instruction cache lines assocoiated with this memory area */ |
| ENTRY(_blackfin_icache_flush_range) |
| do_flush IFLUSH, , nop |
| ENDPROC(_blackfin_icache_flush_range) |
| |
| /* Flush all cache lines assocoiated with this area of memory. */ |
| ENTRY(_blackfin_icache_dcache_flush_range) |
| do_flush IFLUSH, FLUSH |
| ENDPROC(_blackfin_icache_dcache_flush_range) |
| |
| /* Throw away all D-cached data in specified region without any obligation to |
| * write them back. Since the Blackfin ISA does not have an "invalidate" |
| * instruction, we use flush/invalidate. Perhaps as a speed optimization we |
| * could bang on the DTEST MMRs ... |
| */ |
| ENTRY(_blackfin_dcache_invalidate_range) |
| do_flush FLUSHINV |
| ENDPROC(_blackfin_dcache_invalidate_range) |
| |
| /* Flush all data cache lines assocoiated with this memory area */ |
| ENTRY(_blackfin_dcache_flush_range) |
| do_flush FLUSH, , , .Ldfr |
| ENDPROC(_blackfin_dcache_flush_range) |
| |
| /* Our headers convert the page structure to an address, so just need to flush |
| * its contents like normal. We know the start address is page aligned (which |
| * greater than our cache alignment), as is the end address. So just jump into |
| * the middle of the dcache flush function. |
| */ |
| ENTRY(_blackfin_dflush_page) |
| P1 = 1 << (PAGE_SHIFT - L1_CACHE_SHIFT); |
| jump .Ldfr; |
| ENDPROC(_blackfin_dflush_page) |