| /* |
| * Copyright (C) 2011 LAPIS Semiconductor Co., Ltd. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation; version 2 of the License. |
| */ |
| #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt |
| #include <linux/kernel.h> |
| #include <linux/module.h> |
| #include <linux/pci.h> |
| #include <linux/delay.h> |
| #include <linux/errno.h> |
| #include <linux/list.h> |
| #include <linux/interrupt.h> |
| #include <linux/usb/ch9.h> |
| #include <linux/usb/gadget.h> |
| #include <linux/gpio.h> |
| #include <linux/irq.h> |
| |
| /* GPIO port for VBUS detecting */ |
| static int vbus_gpio_port = -1; /* GPIO port number (-1:Not used) */ |
| |
| #define PCH_VBUS_PERIOD 3000 /* VBUS polling period (msec) */ |
| #define PCH_VBUS_INTERVAL 10 /* VBUS polling interval (msec) */ |
| |
| /* Address offset of Registers */ |
| #define UDC_EP_REG_SHIFT 0x20 /* Offset to next EP */ |
| |
| #define UDC_EPCTL_ADDR 0x00 /* Endpoint control */ |
| #define UDC_EPSTS_ADDR 0x04 /* Endpoint status */ |
| #define UDC_BUFIN_FRAMENUM_ADDR 0x08 /* buffer size in / frame number out */ |
| #define UDC_BUFOUT_MAXPKT_ADDR 0x0C /* buffer size out / maxpkt in */ |
| #define UDC_SUBPTR_ADDR 0x10 /* setup buffer pointer */ |
| #define UDC_DESPTR_ADDR 0x14 /* Data descriptor pointer */ |
| #define UDC_CONFIRM_ADDR 0x18 /* Write/Read confirmation */ |
| |
| #define UDC_DEVCFG_ADDR 0x400 /* Device configuration */ |
| #define UDC_DEVCTL_ADDR 0x404 /* Device control */ |
| #define UDC_DEVSTS_ADDR 0x408 /* Device status */ |
| #define UDC_DEVIRQSTS_ADDR 0x40C /* Device irq status */ |
| #define UDC_DEVIRQMSK_ADDR 0x410 /* Device irq mask */ |
| #define UDC_EPIRQSTS_ADDR 0x414 /* Endpoint irq status */ |
| #define UDC_EPIRQMSK_ADDR 0x418 /* Endpoint irq mask */ |
| #define UDC_DEVLPM_ADDR 0x41C /* LPM control / status */ |
| #define UDC_CSR_BUSY_ADDR 0x4f0 /* UDC_CSR_BUSY Status register */ |
| #define UDC_SRST_ADDR 0x4fc /* SOFT RESET register */ |
| #define UDC_CSR_ADDR 0x500 /* USB_DEVICE endpoint register */ |
| |
| /* Endpoint control register */ |
| /* Bit position */ |
| #define UDC_EPCTL_MRXFLUSH (1 << 12) |
| #define UDC_EPCTL_RRDY (1 << 9) |
| #define UDC_EPCTL_CNAK (1 << 8) |
| #define UDC_EPCTL_SNAK (1 << 7) |
| #define UDC_EPCTL_NAK (1 << 6) |
| #define UDC_EPCTL_P (1 << 3) |
| #define UDC_EPCTL_F (1 << 1) |
| #define UDC_EPCTL_S (1 << 0) |
| #define UDC_EPCTL_ET_SHIFT 4 |
| /* Mask patern */ |
| #define UDC_EPCTL_ET_MASK 0x00000030 |
| /* Value for ET field */ |
| #define UDC_EPCTL_ET_CONTROL 0 |
| #define UDC_EPCTL_ET_ISO 1 |
| #define UDC_EPCTL_ET_BULK 2 |
| #define UDC_EPCTL_ET_INTERRUPT 3 |
| |
| /* Endpoint status register */ |
| /* Bit position */ |
| #define UDC_EPSTS_XFERDONE (1 << 27) |
| #define UDC_EPSTS_RSS (1 << 26) |
| #define UDC_EPSTS_RCS (1 << 25) |
| #define UDC_EPSTS_TXEMPTY (1 << 24) |
| #define UDC_EPSTS_TDC (1 << 10) |
| #define UDC_EPSTS_HE (1 << 9) |
| #define UDC_EPSTS_MRXFIFO_EMP (1 << 8) |
| #define UDC_EPSTS_BNA (1 << 7) |
| #define UDC_EPSTS_IN (1 << 6) |
| #define UDC_EPSTS_OUT_SHIFT 4 |
| /* Mask patern */ |
| #define UDC_EPSTS_OUT_MASK 0x00000030 |
| #define UDC_EPSTS_ALL_CLR_MASK 0x1F0006F0 |
| /* Value for OUT field */ |
| #define UDC_EPSTS_OUT_SETUP 2 |
| #define UDC_EPSTS_OUT_DATA 1 |
| |
| /* Device configuration register */ |
| /* Bit position */ |
| #define UDC_DEVCFG_CSR_PRG (1 << 17) |
| #define UDC_DEVCFG_SP (1 << 3) |
| /* SPD Valee */ |
| #define UDC_DEVCFG_SPD_HS 0x0 |
| #define UDC_DEVCFG_SPD_FS 0x1 |
| #define UDC_DEVCFG_SPD_LS 0x2 |
| |
| /* Device control register */ |
| /* Bit position */ |
| #define UDC_DEVCTL_THLEN_SHIFT 24 |
| #define UDC_DEVCTL_BRLEN_SHIFT 16 |
| #define UDC_DEVCTL_CSR_DONE (1 << 13) |
| #define UDC_DEVCTL_SD (1 << 10) |
| #define UDC_DEVCTL_MODE (1 << 9) |
| #define UDC_DEVCTL_BREN (1 << 8) |
| #define UDC_DEVCTL_THE (1 << 7) |
| #define UDC_DEVCTL_DU (1 << 4) |
| #define UDC_DEVCTL_TDE (1 << 3) |
| #define UDC_DEVCTL_RDE (1 << 2) |
| #define UDC_DEVCTL_RES (1 << 0) |
| |
| /* Device status register */ |
| /* Bit position */ |
| #define UDC_DEVSTS_TS_SHIFT 18 |
| #define UDC_DEVSTS_ENUM_SPEED_SHIFT 13 |
| #define UDC_DEVSTS_ALT_SHIFT 8 |
| #define UDC_DEVSTS_INTF_SHIFT 4 |
| #define UDC_DEVSTS_CFG_SHIFT 0 |
| /* Mask patern */ |
| #define UDC_DEVSTS_TS_MASK 0xfffc0000 |
| #define UDC_DEVSTS_ENUM_SPEED_MASK 0x00006000 |
| #define UDC_DEVSTS_ALT_MASK 0x00000f00 |
| #define UDC_DEVSTS_INTF_MASK 0x000000f0 |
| #define UDC_DEVSTS_CFG_MASK 0x0000000f |
| /* value for maximum speed for SPEED field */ |
| #define UDC_DEVSTS_ENUM_SPEED_FULL 1 |
| #define UDC_DEVSTS_ENUM_SPEED_HIGH 0 |
| #define UDC_DEVSTS_ENUM_SPEED_LOW 2 |
| #define UDC_DEVSTS_ENUM_SPEED_FULLX 3 |
| |
| /* Device irq register */ |
| /* Bit position */ |
| #define UDC_DEVINT_RWKP (1 << 7) |
| #define UDC_DEVINT_ENUM (1 << 6) |
| #define UDC_DEVINT_SOF (1 << 5) |
| #define UDC_DEVINT_US (1 << 4) |
| #define UDC_DEVINT_UR (1 << 3) |
| #define UDC_DEVINT_ES (1 << 2) |
| #define UDC_DEVINT_SI (1 << 1) |
| #define UDC_DEVINT_SC (1 << 0) |
| /* Mask patern */ |
| #define UDC_DEVINT_MSK 0x7f |
| |
| /* Endpoint irq register */ |
| /* Bit position */ |
| #define UDC_EPINT_IN_SHIFT 0 |
| #define UDC_EPINT_OUT_SHIFT 16 |
| #define UDC_EPINT_IN_EP0 (1 << 0) |
| #define UDC_EPINT_OUT_EP0 (1 << 16) |
| /* Mask patern */ |
| #define UDC_EPINT_MSK_DISABLE_ALL 0xffffffff |
| |
| /* UDC_CSR_BUSY Status register */ |
| /* Bit position */ |
| #define UDC_CSR_BUSY (1 << 0) |
| |
| /* SOFT RESET register */ |
| /* Bit position */ |
| #define UDC_PSRST (1 << 1) |
| #define UDC_SRST (1 << 0) |
| |
| /* USB_DEVICE endpoint register */ |
| /* Bit position */ |
| #define UDC_CSR_NE_NUM_SHIFT 0 |
| #define UDC_CSR_NE_DIR_SHIFT 4 |
| #define UDC_CSR_NE_TYPE_SHIFT 5 |
| #define UDC_CSR_NE_CFG_SHIFT 7 |
| #define UDC_CSR_NE_INTF_SHIFT 11 |
| #define UDC_CSR_NE_ALT_SHIFT 15 |
| #define UDC_CSR_NE_MAX_PKT_SHIFT 19 |
| /* Mask patern */ |
| #define UDC_CSR_NE_NUM_MASK 0x0000000f |
| #define UDC_CSR_NE_DIR_MASK 0x00000010 |
| #define UDC_CSR_NE_TYPE_MASK 0x00000060 |
| #define UDC_CSR_NE_CFG_MASK 0x00000780 |
| #define UDC_CSR_NE_INTF_MASK 0x00007800 |
| #define UDC_CSR_NE_ALT_MASK 0x00078000 |
| #define UDC_CSR_NE_MAX_PKT_MASK 0x3ff80000 |
| |
| #define PCH_UDC_CSR(ep) (UDC_CSR_ADDR + ep*4) |
| #define PCH_UDC_EPINT(in, num)\ |
| (1 << (num + (in ? UDC_EPINT_IN_SHIFT : UDC_EPINT_OUT_SHIFT))) |
| |
| /* Index of endpoint */ |
| #define UDC_EP0IN_IDX 0 |
| #define UDC_EP0OUT_IDX 1 |
| #define UDC_EPIN_IDX(ep) (ep * 2) |
| #define UDC_EPOUT_IDX(ep) (ep * 2 + 1) |
| #define PCH_UDC_EP0 0 |
| #define PCH_UDC_EP1 1 |
| #define PCH_UDC_EP2 2 |
| #define PCH_UDC_EP3 3 |
| |
| /* Number of endpoint */ |
| #define PCH_UDC_EP_NUM 32 /* Total number of EPs (16 IN,16 OUT) */ |
| #define PCH_UDC_USED_EP_NUM 4 /* EP number of EP's really used */ |
| /* Length Value */ |
| #define PCH_UDC_BRLEN 0x0F /* Burst length */ |
| #define PCH_UDC_THLEN 0x1F /* Threshold length */ |
| /* Value of EP Buffer Size */ |
| #define UDC_EP0IN_BUFF_SIZE 16 |
| #define UDC_EPIN_BUFF_SIZE 256 |
| #define UDC_EP0OUT_BUFF_SIZE 16 |
| #define UDC_EPOUT_BUFF_SIZE 256 |
| /* Value of EP maximum packet size */ |
| #define UDC_EP0IN_MAX_PKT_SIZE 64 |
| #define UDC_EP0OUT_MAX_PKT_SIZE 64 |
| #define UDC_BULK_MAX_PKT_SIZE 512 |
| |
| /* DMA */ |
| #define DMA_DIR_RX 1 /* DMA for data receive */ |
| #define DMA_DIR_TX 2 /* DMA for data transmit */ |
| #define DMA_ADDR_INVALID (~(dma_addr_t)0) |
| #define UDC_DMA_MAXPACKET 65536 /* maximum packet size for DMA */ |
| |
| /** |
| * struct pch_udc_data_dma_desc - Structure to hold DMA descriptor information |
| * for data |
| * @status: Status quadlet |
| * @reserved: Reserved |
| * @dataptr: Buffer descriptor |
| * @next: Next descriptor |
| */ |
| struct pch_udc_data_dma_desc { |
| u32 status; |
| u32 reserved; |
| u32 dataptr; |
| u32 next; |
| }; |
| |
| /** |
| * struct pch_udc_stp_dma_desc - Structure to hold DMA descriptor information |
| * for control data |
| * @status: Status |
| * @reserved: Reserved |
| * @data12: First setup word |
| * @data34: Second setup word |
| */ |
| struct pch_udc_stp_dma_desc { |
| u32 status; |
| u32 reserved; |
| struct usb_ctrlrequest request; |
| } __attribute((packed)); |
| |
| /* DMA status definitions */ |
| /* Buffer status */ |
| #define PCH_UDC_BUFF_STS 0xC0000000 |
| #define PCH_UDC_BS_HST_RDY 0x00000000 |
| #define PCH_UDC_BS_DMA_BSY 0x40000000 |
| #define PCH_UDC_BS_DMA_DONE 0x80000000 |
| #define PCH_UDC_BS_HST_BSY 0xC0000000 |
| /* Rx/Tx Status */ |
| #define PCH_UDC_RXTX_STS 0x30000000 |
| #define PCH_UDC_RTS_SUCC 0x00000000 |
| #define PCH_UDC_RTS_DESERR 0x10000000 |
| #define PCH_UDC_RTS_BUFERR 0x30000000 |
| /* Last Descriptor Indication */ |
| #define PCH_UDC_DMA_LAST 0x08000000 |
| /* Number of Rx/Tx Bytes Mask */ |
| #define PCH_UDC_RXTX_BYTES 0x0000ffff |
| |
| /** |
| * struct pch_udc_cfg_data - Structure to hold current configuration |
| * and interface information |
| * @cur_cfg: current configuration in use |
| * @cur_intf: current interface in use |
| * @cur_alt: current alt interface in use |
| */ |
| struct pch_udc_cfg_data { |
| u16 cur_cfg; |
| u16 cur_intf; |
| u16 cur_alt; |
| }; |
| |
| /** |
| * struct pch_udc_ep - Structure holding a PCH USB device Endpoint information |
| * @ep: embedded ep request |
| * @td_stp_phys: for setup request |
| * @td_data_phys: for data request |
| * @td_stp: for setup request |
| * @td_data: for data request |
| * @dev: reference to device struct |
| * @offset_addr: offset address of ep register |
| * @desc: for this ep |
| * @queue: queue for requests |
| * @num: endpoint number |
| * @in: endpoint is IN |
| * @halted: endpoint halted? |
| * @epsts: Endpoint status |
| */ |
| struct pch_udc_ep { |
| struct usb_ep ep; |
| dma_addr_t td_stp_phys; |
| dma_addr_t td_data_phys; |
| struct pch_udc_stp_dma_desc *td_stp; |
| struct pch_udc_data_dma_desc *td_data; |
| struct pch_udc_dev *dev; |
| unsigned long offset_addr; |
| struct list_head queue; |
| unsigned num:5, |
| in:1, |
| halted:1; |
| unsigned long epsts; |
| }; |
| |
| /** |
| * struct pch_vbus_gpio_data - Structure holding GPIO informaton |
| * for detecting VBUS |
| * @port: gpio port number |
| * @intr: gpio interrupt number |
| * @irq_work_fall Structure for WorkQueue |
| * @irq_work_rise Structure for WorkQueue |
| */ |
| struct pch_vbus_gpio_data { |
| int port; |
| int intr; |
| struct work_struct irq_work_fall; |
| struct work_struct irq_work_rise; |
| }; |
| |
| /** |
| * struct pch_udc_dev - Structure holding complete information |
| * of the PCH USB device |
| * @gadget: gadget driver data |
| * @driver: reference to gadget driver bound |
| * @pdev: reference to the PCI device |
| * @ep: array of endpoints |
| * @lock: protects all state |
| * @active: enabled the PCI device |
| * @stall: stall requested |
| * @prot_stall: protcol stall requested |
| * @irq_registered: irq registered with system |
| * @mem_region: device memory mapped |
| * @registered: driver regsitered with system |
| * @suspended: driver in suspended state |
| * @connected: gadget driver associated |
| * @vbus_session: required vbus_session state |
| * @set_cfg_not_acked: pending acknowledgement 4 setup |
| * @waiting_zlp_ack: pending acknowledgement 4 ZLP |
| * @data_requests: DMA pool for data requests |
| * @stp_requests: DMA pool for setup requests |
| * @dma_addr: DMA pool for received |
| * @ep0out_buf: Buffer for DMA |
| * @setup_data: Received setup data |
| * @phys_addr: of device memory |
| * @base_addr: for mapped device memory |
| * @bar: Indicates which PCI BAR for USB regs |
| * @irq: IRQ line for the device |
| * @cfg_data: current cfg, intf, and alt in use |
| * @vbus_gpio: GPIO informaton for detecting VBUS |
| */ |
| struct pch_udc_dev { |
| struct usb_gadget gadget; |
| struct usb_gadget_driver *driver; |
| struct pci_dev *pdev; |
| struct pch_udc_ep ep[PCH_UDC_EP_NUM]; |
| spinlock_t lock; /* protects all state */ |
| unsigned active:1, |
| stall:1, |
| prot_stall:1, |
| irq_registered:1, |
| mem_region:1, |
| suspended:1, |
| connected:1, |
| vbus_session:1, |
| set_cfg_not_acked:1, |
| waiting_zlp_ack:1; |
| struct pci_pool *data_requests; |
| struct pci_pool *stp_requests; |
| dma_addr_t dma_addr; |
| void *ep0out_buf; |
| struct usb_ctrlrequest setup_data; |
| unsigned long phys_addr; |
| void __iomem *base_addr; |
| unsigned bar; |
| unsigned irq; |
| struct pch_udc_cfg_data cfg_data; |
| struct pch_vbus_gpio_data vbus_gpio; |
| }; |
| #define to_pch_udc(g) (container_of((g), struct pch_udc_dev, gadget)) |
| |
| #define PCH_UDC_PCI_BAR_QUARK_X1000 0 |
| #define PCH_UDC_PCI_BAR 1 |
| #define PCI_DEVICE_ID_INTEL_EG20T_UDC 0x8808 |
| #define PCI_DEVICE_ID_INTEL_QUARK_X1000_UDC 0x0939 |
| #define PCI_VENDOR_ID_ROHM 0x10DB |
| #define PCI_DEVICE_ID_ML7213_IOH_UDC 0x801D |
| #define PCI_DEVICE_ID_ML7831_IOH_UDC 0x8808 |
| |
| static const char ep0_string[] = "ep0in"; |
| static DEFINE_SPINLOCK(udc_stall_spinlock); /* stall spin lock */ |
| static bool speed_fs; |
| module_param_named(speed_fs, speed_fs, bool, S_IRUGO); |
| MODULE_PARM_DESC(speed_fs, "true for Full speed operation"); |
| |
| /** |
| * struct pch_udc_request - Structure holding a PCH USB device request packet |
| * @req: embedded ep request |
| * @td_data_phys: phys. address |
| * @td_data: first dma desc. of chain |
| * @td_data_last: last dma desc. of chain |
| * @queue: associated queue |
| * @dma_going: DMA in progress for request |
| * @dma_mapped: DMA memory mapped for request |
| * @dma_done: DMA completed for request |
| * @chain_len: chain length |
| * @buf: Buffer memory for align adjustment |
| * @dma: DMA memory for align adjustment |
| */ |
| struct pch_udc_request { |
| struct usb_request req; |
| dma_addr_t td_data_phys; |
| struct pch_udc_data_dma_desc *td_data; |
| struct pch_udc_data_dma_desc *td_data_last; |
| struct list_head queue; |
| unsigned dma_going:1, |
| dma_mapped:1, |
| dma_done:1; |
| unsigned chain_len; |
| void *buf; |
| dma_addr_t dma; |
| }; |
| |
| static inline u32 pch_udc_readl(struct pch_udc_dev *dev, unsigned long reg) |
| { |
| return ioread32(dev->base_addr + reg); |
| } |
| |
| static inline void pch_udc_writel(struct pch_udc_dev *dev, |
| unsigned long val, unsigned long reg) |
| { |
| iowrite32(val, dev->base_addr + reg); |
| } |
| |
| static inline void pch_udc_bit_set(struct pch_udc_dev *dev, |
| unsigned long reg, |
| unsigned long bitmask) |
| { |
| pch_udc_writel(dev, pch_udc_readl(dev, reg) | bitmask, reg); |
| } |
| |
| static inline void pch_udc_bit_clr(struct pch_udc_dev *dev, |
| unsigned long reg, |
| unsigned long bitmask) |
| { |
| pch_udc_writel(dev, pch_udc_readl(dev, reg) & ~(bitmask), reg); |
| } |
| |
| static inline u32 pch_udc_ep_readl(struct pch_udc_ep *ep, unsigned long reg) |
| { |
| return ioread32(ep->dev->base_addr + ep->offset_addr + reg); |
| } |
| |
| static inline void pch_udc_ep_writel(struct pch_udc_ep *ep, |
| unsigned long val, unsigned long reg) |
| { |
| iowrite32(val, ep->dev->base_addr + ep->offset_addr + reg); |
| } |
| |
| static inline void pch_udc_ep_bit_set(struct pch_udc_ep *ep, |
| unsigned long reg, |
| unsigned long bitmask) |
| { |
| pch_udc_ep_writel(ep, pch_udc_ep_readl(ep, reg) | bitmask, reg); |
| } |
| |
| static inline void pch_udc_ep_bit_clr(struct pch_udc_ep *ep, |
| unsigned long reg, |
| unsigned long bitmask) |
| { |
| pch_udc_ep_writel(ep, pch_udc_ep_readl(ep, reg) & ~(bitmask), reg); |
| } |
| |
| /** |
| * pch_udc_csr_busy() - Wait till idle. |
| * @dev: Reference to pch_udc_dev structure |
| */ |
| static void pch_udc_csr_busy(struct pch_udc_dev *dev) |
| { |
| unsigned int count = 200; |
| |
| /* Wait till idle */ |
| while ((pch_udc_readl(dev, UDC_CSR_BUSY_ADDR) & UDC_CSR_BUSY) |
| && --count) |
| cpu_relax(); |
| if (!count) |
| dev_err(&dev->pdev->dev, "%s: wait error\n", __func__); |
| } |
| |
| /** |
| * pch_udc_write_csr() - Write the command and status registers. |
| * @dev: Reference to pch_udc_dev structure |
| * @val: value to be written to CSR register |
| * @addr: address of CSR register |
| */ |
| static void pch_udc_write_csr(struct pch_udc_dev *dev, unsigned long val, |
| unsigned int ep) |
| { |
| unsigned long reg = PCH_UDC_CSR(ep); |
| |
| pch_udc_csr_busy(dev); /* Wait till idle */ |
| pch_udc_writel(dev, val, reg); |
| pch_udc_csr_busy(dev); /* Wait till idle */ |
| } |
| |
| /** |
| * pch_udc_read_csr() - Read the command and status registers. |
| * @dev: Reference to pch_udc_dev structure |
| * @addr: address of CSR register |
| * |
| * Return codes: content of CSR register |
| */ |
| static u32 pch_udc_read_csr(struct pch_udc_dev *dev, unsigned int ep) |
| { |
| unsigned long reg = PCH_UDC_CSR(ep); |
| |
| pch_udc_csr_busy(dev); /* Wait till idle */ |
| pch_udc_readl(dev, reg); /* Dummy read */ |
| pch_udc_csr_busy(dev); /* Wait till idle */ |
| return pch_udc_readl(dev, reg); |
| } |
| |
| /** |
| * pch_udc_rmt_wakeup() - Initiate for remote wakeup |
| * @dev: Reference to pch_udc_dev structure |
| */ |
| static inline void pch_udc_rmt_wakeup(struct pch_udc_dev *dev) |
| { |
| pch_udc_bit_set(dev, UDC_DEVCTL_ADDR, UDC_DEVCTL_RES); |
| mdelay(1); |
| pch_udc_bit_clr(dev, UDC_DEVCTL_ADDR, UDC_DEVCTL_RES); |
| } |
| |
| /** |
| * pch_udc_get_frame() - Get the current frame from device status register |
| * @dev: Reference to pch_udc_dev structure |
| * Retern current frame |
| */ |
| static inline int pch_udc_get_frame(struct pch_udc_dev *dev) |
| { |
| u32 frame = pch_udc_readl(dev, UDC_DEVSTS_ADDR); |
| return (frame & UDC_DEVSTS_TS_MASK) >> UDC_DEVSTS_TS_SHIFT; |
| } |
| |
| /** |
| * pch_udc_clear_selfpowered() - Clear the self power control |
| * @dev: Reference to pch_udc_regs structure |
| */ |
| static inline void pch_udc_clear_selfpowered(struct pch_udc_dev *dev) |
| { |
| pch_udc_bit_clr(dev, UDC_DEVCFG_ADDR, UDC_DEVCFG_SP); |
| } |
| |
| /** |
| * pch_udc_set_selfpowered() - Set the self power control |
| * @dev: Reference to pch_udc_regs structure |
| */ |
| static inline void pch_udc_set_selfpowered(struct pch_udc_dev *dev) |
| { |
| pch_udc_bit_set(dev, UDC_DEVCFG_ADDR, UDC_DEVCFG_SP); |
| } |
| |
| /** |
| * pch_udc_set_disconnect() - Set the disconnect status. |
| * @dev: Reference to pch_udc_regs structure |
| */ |
| static inline void pch_udc_set_disconnect(struct pch_udc_dev *dev) |
| { |
| pch_udc_bit_set(dev, UDC_DEVCTL_ADDR, UDC_DEVCTL_SD); |
| } |
| |
| /** |
| * pch_udc_clear_disconnect() - Clear the disconnect status. |
| * @dev: Reference to pch_udc_regs structure |
| */ |
| static void pch_udc_clear_disconnect(struct pch_udc_dev *dev) |
| { |
| /* Clear the disconnect */ |
| pch_udc_bit_set(dev, UDC_DEVCTL_ADDR, UDC_DEVCTL_RES); |
| pch_udc_bit_clr(dev, UDC_DEVCTL_ADDR, UDC_DEVCTL_SD); |
| mdelay(1); |
| /* Resume USB signalling */ |
| pch_udc_bit_clr(dev, UDC_DEVCTL_ADDR, UDC_DEVCTL_RES); |
| } |
| |
| /** |
| * pch_udc_reconnect() - This API initializes usb device controller, |
| * and clear the disconnect status. |
| * @dev: Reference to pch_udc_regs structure |
| */ |
| static void pch_udc_init(struct pch_udc_dev *dev); |
| static void pch_udc_reconnect(struct pch_udc_dev *dev) |
| { |
| pch_udc_init(dev); |
| |
| /* enable device interrupts */ |
| /* pch_udc_enable_interrupts() */ |
| pch_udc_bit_clr(dev, UDC_DEVIRQMSK_ADDR, |
| UDC_DEVINT_UR | UDC_DEVINT_ENUM); |
| |
| /* Clear the disconnect */ |
| pch_udc_bit_set(dev, UDC_DEVCTL_ADDR, UDC_DEVCTL_RES); |
| pch_udc_bit_clr(dev, UDC_DEVCTL_ADDR, UDC_DEVCTL_SD); |
| mdelay(1); |
| /* Resume USB signalling */ |
| pch_udc_bit_clr(dev, UDC_DEVCTL_ADDR, UDC_DEVCTL_RES); |
| } |
| |
| /** |
| * pch_udc_vbus_session() - set or clearr the disconnect status. |
| * @dev: Reference to pch_udc_regs structure |
| * @is_active: Parameter specifying the action |
| * 0: indicating VBUS power is ending |
| * !0: indicating VBUS power is starting |
| */ |
| static inline void pch_udc_vbus_session(struct pch_udc_dev *dev, |
| int is_active) |
| { |
| if (is_active) { |
| pch_udc_reconnect(dev); |
| dev->vbus_session = 1; |
| } else { |
| if (dev->driver && dev->driver->disconnect) { |
| spin_unlock(&dev->lock); |
| dev->driver->disconnect(&dev->gadget); |
| spin_lock(&dev->lock); |
| } |
| pch_udc_set_disconnect(dev); |
| dev->vbus_session = 0; |
| } |
| } |
| |
| /** |
| * pch_udc_ep_set_stall() - Set the stall of endpoint |
| * @ep: Reference to structure of type pch_udc_ep_regs |
| */ |
| static void pch_udc_ep_set_stall(struct pch_udc_ep *ep) |
| { |
| if (ep->in) { |
| pch_udc_ep_bit_set(ep, UDC_EPCTL_ADDR, UDC_EPCTL_F); |
| pch_udc_ep_bit_set(ep, UDC_EPCTL_ADDR, UDC_EPCTL_S); |
| } else { |
| pch_udc_ep_bit_set(ep, UDC_EPCTL_ADDR, UDC_EPCTL_S); |
| } |
| } |
| |
| /** |
| * pch_udc_ep_clear_stall() - Clear the stall of endpoint |
| * @ep: Reference to structure of type pch_udc_ep_regs |
| */ |
| static inline void pch_udc_ep_clear_stall(struct pch_udc_ep *ep) |
| { |
| /* Clear the stall */ |
| pch_udc_ep_bit_clr(ep, UDC_EPCTL_ADDR, UDC_EPCTL_S); |
| /* Clear NAK by writing CNAK */ |
| pch_udc_ep_bit_set(ep, UDC_EPCTL_ADDR, UDC_EPCTL_CNAK); |
| } |
| |
| /** |
| * pch_udc_ep_set_trfr_type() - Set the transfer type of endpoint |
| * @ep: Reference to structure of type pch_udc_ep_regs |
| * @type: Type of endpoint |
| */ |
| static inline void pch_udc_ep_set_trfr_type(struct pch_udc_ep *ep, |
| u8 type) |
| { |
| pch_udc_ep_writel(ep, ((type << UDC_EPCTL_ET_SHIFT) & |
| UDC_EPCTL_ET_MASK), UDC_EPCTL_ADDR); |
| } |
| |
| /** |
| * pch_udc_ep_set_bufsz() - Set the maximum packet size for the endpoint |
| * @ep: Reference to structure of type pch_udc_ep_regs |
| * @buf_size: The buffer word size |
| */ |
| static void pch_udc_ep_set_bufsz(struct pch_udc_ep *ep, |
| u32 buf_size, u32 ep_in) |
| { |
| u32 data; |
| if (ep_in) { |
| data = pch_udc_ep_readl(ep, UDC_BUFIN_FRAMENUM_ADDR); |
| data = (data & 0xffff0000) | (buf_size & 0xffff); |
| pch_udc_ep_writel(ep, data, UDC_BUFIN_FRAMENUM_ADDR); |
| } else { |
| data = pch_udc_ep_readl(ep, UDC_BUFOUT_MAXPKT_ADDR); |
| data = (buf_size << 16) | (data & 0xffff); |
| pch_udc_ep_writel(ep, data, UDC_BUFOUT_MAXPKT_ADDR); |
| } |
| } |
| |
| /** |
| * pch_udc_ep_set_maxpkt() - Set the Max packet size for the endpoint |
| * @ep: Reference to structure of type pch_udc_ep_regs |
| * @pkt_size: The packet byte size |
| */ |
| static void pch_udc_ep_set_maxpkt(struct pch_udc_ep *ep, u32 pkt_size) |
| { |
| u32 data = pch_udc_ep_readl(ep, UDC_BUFOUT_MAXPKT_ADDR); |
| data = (data & 0xffff0000) | (pkt_size & 0xffff); |
| pch_udc_ep_writel(ep, data, UDC_BUFOUT_MAXPKT_ADDR); |
| } |
| |
| /** |
| * pch_udc_ep_set_subptr() - Set the Setup buffer pointer for the endpoint |
| * @ep: Reference to structure of type pch_udc_ep_regs |
| * @addr: Address of the register |
| */ |
| static inline void pch_udc_ep_set_subptr(struct pch_udc_ep *ep, u32 addr) |
| { |
| pch_udc_ep_writel(ep, addr, UDC_SUBPTR_ADDR); |
| } |
| |
| /** |
| * pch_udc_ep_set_ddptr() - Set the Data descriptor pointer for the endpoint |
| * @ep: Reference to structure of type pch_udc_ep_regs |
| * @addr: Address of the register |
| */ |
| static inline void pch_udc_ep_set_ddptr(struct pch_udc_ep *ep, u32 addr) |
| { |
| pch_udc_ep_writel(ep, addr, UDC_DESPTR_ADDR); |
| } |
| |
| /** |
| * pch_udc_ep_set_pd() - Set the poll demand bit for the endpoint |
| * @ep: Reference to structure of type pch_udc_ep_regs |
| */ |
| static inline void pch_udc_ep_set_pd(struct pch_udc_ep *ep) |
| { |
| pch_udc_ep_bit_set(ep, UDC_EPCTL_ADDR, UDC_EPCTL_P); |
| } |
| |
| /** |
| * pch_udc_ep_set_rrdy() - Set the receive ready bit for the endpoint |
| * @ep: Reference to structure of type pch_udc_ep_regs |
| */ |
| static inline void pch_udc_ep_set_rrdy(struct pch_udc_ep *ep) |
| { |
| pch_udc_ep_bit_set(ep, UDC_EPCTL_ADDR, UDC_EPCTL_RRDY); |
| } |
| |
| /** |
| * pch_udc_ep_clear_rrdy() - Clear the receive ready bit for the endpoint |
| * @ep: Reference to structure of type pch_udc_ep_regs |
| */ |
| static inline void pch_udc_ep_clear_rrdy(struct pch_udc_ep *ep) |
| { |
| pch_udc_ep_bit_clr(ep, UDC_EPCTL_ADDR, UDC_EPCTL_RRDY); |
| } |
| |
| /** |
| * pch_udc_set_dma() - Set the 'TDE' or RDE bit of device control |
| * register depending on the direction specified |
| * @dev: Reference to structure of type pch_udc_regs |
| * @dir: whether Tx or Rx |
| * DMA_DIR_RX: Receive |
| * DMA_DIR_TX: Transmit |
| */ |
| static inline void pch_udc_set_dma(struct pch_udc_dev *dev, int dir) |
| { |
| if (dir == DMA_DIR_RX) |
| pch_udc_bit_set(dev, UDC_DEVCTL_ADDR, UDC_DEVCTL_RDE); |
| else if (dir == DMA_DIR_TX) |
| pch_udc_bit_set(dev, UDC_DEVCTL_ADDR, UDC_DEVCTL_TDE); |
| } |
| |
| /** |
| * pch_udc_clear_dma() - Clear the 'TDE' or RDE bit of device control |
| * register depending on the direction specified |
| * @dev: Reference to structure of type pch_udc_regs |
| * @dir: Whether Tx or Rx |
| * DMA_DIR_RX: Receive |
| * DMA_DIR_TX: Transmit |
| */ |
| static inline void pch_udc_clear_dma(struct pch_udc_dev *dev, int dir) |
| { |
| if (dir == DMA_DIR_RX) |
| pch_udc_bit_clr(dev, UDC_DEVCTL_ADDR, UDC_DEVCTL_RDE); |
| else if (dir == DMA_DIR_TX) |
| pch_udc_bit_clr(dev, UDC_DEVCTL_ADDR, UDC_DEVCTL_TDE); |
| } |
| |
| /** |
| * pch_udc_set_csr_done() - Set the device control register |
| * CSR done field (bit 13) |
| * @dev: reference to structure of type pch_udc_regs |
| */ |
| static inline void pch_udc_set_csr_done(struct pch_udc_dev *dev) |
| { |
| pch_udc_bit_set(dev, UDC_DEVCTL_ADDR, UDC_DEVCTL_CSR_DONE); |
| } |
| |
| /** |
| * pch_udc_disable_interrupts() - Disables the specified interrupts |
| * @dev: Reference to structure of type pch_udc_regs |
| * @mask: Mask to disable interrupts |
| */ |
| static inline void pch_udc_disable_interrupts(struct pch_udc_dev *dev, |
| u32 mask) |
| { |
| pch_udc_bit_set(dev, UDC_DEVIRQMSK_ADDR, mask); |
| } |
| |
| /** |
| * pch_udc_enable_interrupts() - Enable the specified interrupts |
| * @dev: Reference to structure of type pch_udc_regs |
| * @mask: Mask to enable interrupts |
| */ |
| static inline void pch_udc_enable_interrupts(struct pch_udc_dev *dev, |
| u32 mask) |
| { |
| pch_udc_bit_clr(dev, UDC_DEVIRQMSK_ADDR, mask); |
| } |
| |
| /** |
| * pch_udc_disable_ep_interrupts() - Disable endpoint interrupts |
| * @dev: Reference to structure of type pch_udc_regs |
| * @mask: Mask to disable interrupts |
| */ |
| static inline void pch_udc_disable_ep_interrupts(struct pch_udc_dev *dev, |
| u32 mask) |
| { |
| pch_udc_bit_set(dev, UDC_EPIRQMSK_ADDR, mask); |
| } |
| |
| /** |
| * pch_udc_enable_ep_interrupts() - Enable endpoint interrupts |
| * @dev: Reference to structure of type pch_udc_regs |
| * @mask: Mask to enable interrupts |
| */ |
| static inline void pch_udc_enable_ep_interrupts(struct pch_udc_dev *dev, |
| u32 mask) |
| { |
| pch_udc_bit_clr(dev, UDC_EPIRQMSK_ADDR, mask); |
| } |
| |
| /** |
| * pch_udc_read_device_interrupts() - Read the device interrupts |
| * @dev: Reference to structure of type pch_udc_regs |
| * Retern The device interrupts |
| */ |
| static inline u32 pch_udc_read_device_interrupts(struct pch_udc_dev *dev) |
| { |
| return pch_udc_readl(dev, UDC_DEVIRQSTS_ADDR); |
| } |
| |
| /** |
| * pch_udc_write_device_interrupts() - Write device interrupts |
| * @dev: Reference to structure of type pch_udc_regs |
| * @val: The value to be written to interrupt register |
| */ |
| static inline void pch_udc_write_device_interrupts(struct pch_udc_dev *dev, |
| u32 val) |
| { |
| pch_udc_writel(dev, val, UDC_DEVIRQSTS_ADDR); |
| } |
| |
| /** |
| * pch_udc_read_ep_interrupts() - Read the endpoint interrupts |
| * @dev: Reference to structure of type pch_udc_regs |
| * Retern The endpoint interrupt |
| */ |
| static inline u32 pch_udc_read_ep_interrupts(struct pch_udc_dev *dev) |
| { |
| return pch_udc_readl(dev, UDC_EPIRQSTS_ADDR); |
| } |
| |
| /** |
| * pch_udc_write_ep_interrupts() - Clear endpoint interupts |
| * @dev: Reference to structure of type pch_udc_regs |
| * @val: The value to be written to interrupt register |
| */ |
| static inline void pch_udc_write_ep_interrupts(struct pch_udc_dev *dev, |
| u32 val) |
| { |
| pch_udc_writel(dev, val, UDC_EPIRQSTS_ADDR); |
| } |
| |
| /** |
| * pch_udc_read_device_status() - Read the device status |
| * @dev: Reference to structure of type pch_udc_regs |
| * Retern The device status |
| */ |
| static inline u32 pch_udc_read_device_status(struct pch_udc_dev *dev) |
| { |
| return pch_udc_readl(dev, UDC_DEVSTS_ADDR); |
| } |
| |
| /** |
| * pch_udc_read_ep_control() - Read the endpoint control |
| * @ep: Reference to structure of type pch_udc_ep_regs |
| * Retern The endpoint control register value |
| */ |
| static inline u32 pch_udc_read_ep_control(struct pch_udc_ep *ep) |
| { |
| return pch_udc_ep_readl(ep, UDC_EPCTL_ADDR); |
| } |
| |
| /** |
| * pch_udc_clear_ep_control() - Clear the endpoint control register |
| * @ep: Reference to structure of type pch_udc_ep_regs |
| * Retern The endpoint control register value |
| */ |
| static inline void pch_udc_clear_ep_control(struct pch_udc_ep *ep) |
| { |
| return pch_udc_ep_writel(ep, 0, UDC_EPCTL_ADDR); |
| } |
| |
| /** |
| * pch_udc_read_ep_status() - Read the endpoint status |
| * @ep: Reference to structure of type pch_udc_ep_regs |
| * Retern The endpoint status |
| */ |
| static inline u32 pch_udc_read_ep_status(struct pch_udc_ep *ep) |
| { |
| return pch_udc_ep_readl(ep, UDC_EPSTS_ADDR); |
| } |
| |
| /** |
| * pch_udc_clear_ep_status() - Clear the endpoint status |
| * @ep: Reference to structure of type pch_udc_ep_regs |
| * @stat: Endpoint status |
| */ |
| static inline void pch_udc_clear_ep_status(struct pch_udc_ep *ep, |
| u32 stat) |
| { |
| return pch_udc_ep_writel(ep, stat, UDC_EPSTS_ADDR); |
| } |
| |
| /** |
| * pch_udc_ep_set_nak() - Set the bit 7 (SNAK field) |
| * of the endpoint control register |
| * @ep: Reference to structure of type pch_udc_ep_regs |
| */ |
| static inline void pch_udc_ep_set_nak(struct pch_udc_ep *ep) |
| { |
| pch_udc_ep_bit_set(ep, UDC_EPCTL_ADDR, UDC_EPCTL_SNAK); |
| } |
| |
| /** |
| * pch_udc_ep_clear_nak() - Set the bit 8 (CNAK field) |
| * of the endpoint control register |
| * @ep: reference to structure of type pch_udc_ep_regs |
| */ |
| static void pch_udc_ep_clear_nak(struct pch_udc_ep *ep) |
| { |
| unsigned int loopcnt = 0; |
| struct pch_udc_dev *dev = ep->dev; |
| |
| if (!(pch_udc_ep_readl(ep, UDC_EPCTL_ADDR) & UDC_EPCTL_NAK)) |
| return; |
| if (!ep->in) { |
| loopcnt = 10000; |
| while (!(pch_udc_read_ep_status(ep) & UDC_EPSTS_MRXFIFO_EMP) && |
| --loopcnt) |
| udelay(5); |
| if (!loopcnt) |
| dev_err(&dev->pdev->dev, "%s: RxFIFO not Empty\n", |
| __func__); |
| } |
| loopcnt = 10000; |
| while ((pch_udc_read_ep_control(ep) & UDC_EPCTL_NAK) && --loopcnt) { |
| pch_udc_ep_bit_set(ep, UDC_EPCTL_ADDR, UDC_EPCTL_CNAK); |
| udelay(5); |
| } |
| if (!loopcnt) |
| dev_err(&dev->pdev->dev, "%s: Clear NAK not set for ep%d%s\n", |
| __func__, ep->num, (ep->in ? "in" : "out")); |
| } |
| |
| /** |
| * pch_udc_ep_fifo_flush() - Flush the endpoint fifo |
| * @ep: reference to structure of type pch_udc_ep_regs |
| * @dir: direction of endpoint |
| * 0: endpoint is OUT |
| * !0: endpoint is IN |
| */ |
| static void pch_udc_ep_fifo_flush(struct pch_udc_ep *ep, int dir) |
| { |
| if (dir) { /* IN ep */ |
| pch_udc_ep_bit_set(ep, UDC_EPCTL_ADDR, UDC_EPCTL_F); |
| return; |
| } |
| } |
| |
| /** |
| * pch_udc_ep_enable() - This api enables endpoint |
| * @regs: Reference to structure pch_udc_ep_regs |
| * @desc: endpoint descriptor |
| */ |
| static void pch_udc_ep_enable(struct pch_udc_ep *ep, |
| struct pch_udc_cfg_data *cfg, |
| const struct usb_endpoint_descriptor *desc) |
| { |
| u32 val = 0; |
| u32 buff_size = 0; |
| |
| pch_udc_ep_set_trfr_type(ep, desc->bmAttributes); |
| if (ep->in) |
| buff_size = UDC_EPIN_BUFF_SIZE; |
| else |
| buff_size = UDC_EPOUT_BUFF_SIZE; |
| pch_udc_ep_set_bufsz(ep, buff_size, ep->in); |
| pch_udc_ep_set_maxpkt(ep, usb_endpoint_maxp(desc)); |
| pch_udc_ep_set_nak(ep); |
| pch_udc_ep_fifo_flush(ep, ep->in); |
| /* Configure the endpoint */ |
| val = ep->num << UDC_CSR_NE_NUM_SHIFT | ep->in << UDC_CSR_NE_DIR_SHIFT | |
| ((desc->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK) << |
| UDC_CSR_NE_TYPE_SHIFT) | |
| (cfg->cur_cfg << UDC_CSR_NE_CFG_SHIFT) | |
| (cfg->cur_intf << UDC_CSR_NE_INTF_SHIFT) | |
| (cfg->cur_alt << UDC_CSR_NE_ALT_SHIFT) | |
| usb_endpoint_maxp(desc) << UDC_CSR_NE_MAX_PKT_SHIFT; |
| |
| if (ep->in) |
| pch_udc_write_csr(ep->dev, val, UDC_EPIN_IDX(ep->num)); |
| else |
| pch_udc_write_csr(ep->dev, val, UDC_EPOUT_IDX(ep->num)); |
| } |
| |
| /** |
| * pch_udc_ep_disable() - This api disables endpoint |
| * @regs: Reference to structure pch_udc_ep_regs |
| */ |
| static void pch_udc_ep_disable(struct pch_udc_ep *ep) |
| { |
| if (ep->in) { |
| /* flush the fifo */ |
| pch_udc_ep_writel(ep, UDC_EPCTL_F, UDC_EPCTL_ADDR); |
| /* set NAK */ |
| pch_udc_ep_writel(ep, UDC_EPCTL_SNAK, UDC_EPCTL_ADDR); |
| pch_udc_ep_bit_set(ep, UDC_EPSTS_ADDR, UDC_EPSTS_IN); |
| } else { |
| /* set NAK */ |
| pch_udc_ep_writel(ep, UDC_EPCTL_SNAK, UDC_EPCTL_ADDR); |
| } |
| /* reset desc pointer */ |
| pch_udc_ep_writel(ep, 0, UDC_DESPTR_ADDR); |
| } |
| |
| /** |
| * pch_udc_wait_ep_stall() - Wait EP stall. |
| * @dev: Reference to pch_udc_dev structure |
| */ |
| static void pch_udc_wait_ep_stall(struct pch_udc_ep *ep) |
| { |
| unsigned int count = 10000; |
| |
| /* Wait till idle */ |
| while ((pch_udc_read_ep_control(ep) & UDC_EPCTL_S) && --count) |
| udelay(5); |
| if (!count) |
| dev_err(&ep->dev->pdev->dev, "%s: wait error\n", __func__); |
| } |
| |
| /** |
| * pch_udc_init() - This API initializes usb device controller |
| * @dev: Rreference to pch_udc_regs structure |
| */ |
| static void pch_udc_init(struct pch_udc_dev *dev) |
| { |
| if (NULL == dev) { |
| pr_err("%s: Invalid address\n", __func__); |
| return; |
| } |
| /* Soft Reset and Reset PHY */ |
| pch_udc_writel(dev, UDC_SRST, UDC_SRST_ADDR); |
| pch_udc_writel(dev, UDC_SRST | UDC_PSRST, UDC_SRST_ADDR); |
| mdelay(1); |
| pch_udc_writel(dev, UDC_SRST, UDC_SRST_ADDR); |
| pch_udc_writel(dev, 0x00, UDC_SRST_ADDR); |
| mdelay(1); |
| /* mask and clear all device interrupts */ |
| pch_udc_bit_set(dev, UDC_DEVIRQMSK_ADDR, UDC_DEVINT_MSK); |
| pch_udc_bit_set(dev, UDC_DEVIRQSTS_ADDR, UDC_DEVINT_MSK); |
| |
| /* mask and clear all ep interrupts */ |
| pch_udc_bit_set(dev, UDC_EPIRQMSK_ADDR, UDC_EPINT_MSK_DISABLE_ALL); |
| pch_udc_bit_set(dev, UDC_EPIRQSTS_ADDR, UDC_EPINT_MSK_DISABLE_ALL); |
| |
| /* enable dynamic CSR programmingi, self powered and device speed */ |
| if (speed_fs) |
| pch_udc_bit_set(dev, UDC_DEVCFG_ADDR, UDC_DEVCFG_CSR_PRG | |
| UDC_DEVCFG_SP | UDC_DEVCFG_SPD_FS); |
| else /* defaul high speed */ |
| pch_udc_bit_set(dev, UDC_DEVCFG_ADDR, UDC_DEVCFG_CSR_PRG | |
| UDC_DEVCFG_SP | UDC_DEVCFG_SPD_HS); |
| pch_udc_bit_set(dev, UDC_DEVCTL_ADDR, |
| (PCH_UDC_THLEN << UDC_DEVCTL_THLEN_SHIFT) | |
| (PCH_UDC_BRLEN << UDC_DEVCTL_BRLEN_SHIFT) | |
| UDC_DEVCTL_MODE | UDC_DEVCTL_BREN | |
| UDC_DEVCTL_THE); |
| } |
| |
| /** |
| * pch_udc_exit() - This API exit usb device controller |
| * @dev: Reference to pch_udc_regs structure |
| */ |
| static void pch_udc_exit(struct pch_udc_dev *dev) |
| { |
| /* mask all device interrupts */ |
| pch_udc_bit_set(dev, UDC_DEVIRQMSK_ADDR, UDC_DEVINT_MSK); |
| /* mask all ep interrupts */ |
| pch_udc_bit_set(dev, UDC_EPIRQMSK_ADDR, UDC_EPINT_MSK_DISABLE_ALL); |
| /* put device in disconnected state */ |
| pch_udc_set_disconnect(dev); |
| } |
| |
| /** |
| * pch_udc_pcd_get_frame() - This API is invoked to get the current frame number |
| * @gadget: Reference to the gadget driver |
| * |
| * Return codes: |
| * 0: Success |
| * -EINVAL: If the gadget passed is NULL |
| */ |
| static int pch_udc_pcd_get_frame(struct usb_gadget *gadget) |
| { |
| struct pch_udc_dev *dev; |
| |
| if (!gadget) |
| return -EINVAL; |
| dev = container_of(gadget, struct pch_udc_dev, gadget); |
| return pch_udc_get_frame(dev); |
| } |
| |
| /** |
| * pch_udc_pcd_wakeup() - This API is invoked to initiate a remote wakeup |
| * @gadget: Reference to the gadget driver |
| * |
| * Return codes: |
| * 0: Success |
| * -EINVAL: If the gadget passed is NULL |
| */ |
| static int pch_udc_pcd_wakeup(struct usb_gadget *gadget) |
| { |
| struct pch_udc_dev *dev; |
| unsigned long flags; |
| |
| if (!gadget) |
| return -EINVAL; |
| dev = container_of(gadget, struct pch_udc_dev, gadget); |
| spin_lock_irqsave(&dev->lock, flags); |
| pch_udc_rmt_wakeup(dev); |
| spin_unlock_irqrestore(&dev->lock, flags); |
| return 0; |
| } |
| |
| /** |
| * pch_udc_pcd_selfpowered() - This API is invoked to specify whether the device |
| * is self powered or not |
| * @gadget: Reference to the gadget driver |
| * @value: Specifies self powered or not |
| * |
| * Return codes: |
| * 0: Success |
| * -EINVAL: If the gadget passed is NULL |
| */ |
| static int pch_udc_pcd_selfpowered(struct usb_gadget *gadget, int value) |
| { |
| struct pch_udc_dev *dev; |
| |
| if (!gadget) |
| return -EINVAL; |
| dev = container_of(gadget, struct pch_udc_dev, gadget); |
| if (value) |
| pch_udc_set_selfpowered(dev); |
| else |
| pch_udc_clear_selfpowered(dev); |
| return 0; |
| } |
| |
| /** |
| * pch_udc_pcd_pullup() - This API is invoked to make the device |
| * visible/invisible to the host |
| * @gadget: Reference to the gadget driver |
| * @is_on: Specifies whether the pull up is made active or inactive |
| * |
| * Return codes: |
| * 0: Success |
| * -EINVAL: If the gadget passed is NULL |
| */ |
| static int pch_udc_pcd_pullup(struct usb_gadget *gadget, int is_on) |
| { |
| struct pch_udc_dev *dev; |
| |
| if (!gadget) |
| return -EINVAL; |
| dev = container_of(gadget, struct pch_udc_dev, gadget); |
| if (is_on) { |
| pch_udc_reconnect(dev); |
| } else { |
| if (dev->driver && dev->driver->disconnect) { |
| spin_unlock(&dev->lock); |
| dev->driver->disconnect(&dev->gadget); |
| spin_lock(&dev->lock); |
| } |
| pch_udc_set_disconnect(dev); |
| } |
| |
| return 0; |
| } |
| |
| /** |
| * pch_udc_pcd_vbus_session() - This API is used by a driver for an external |
| * transceiver (or GPIO) that |
| * detects a VBUS power session starting/ending |
| * @gadget: Reference to the gadget driver |
| * @is_active: specifies whether the session is starting or ending |
| * |
| * Return codes: |
| * 0: Success |
| * -EINVAL: If the gadget passed is NULL |
| */ |
| static int pch_udc_pcd_vbus_session(struct usb_gadget *gadget, int is_active) |
| { |
| struct pch_udc_dev *dev; |
| |
| if (!gadget) |
| return -EINVAL; |
| dev = container_of(gadget, struct pch_udc_dev, gadget); |
| pch_udc_vbus_session(dev, is_active); |
| return 0; |
| } |
| |
| /** |
| * pch_udc_pcd_vbus_draw() - This API is used by gadget drivers during |
| * SET_CONFIGURATION calls to |
| * specify how much power the device can consume |
| * @gadget: Reference to the gadget driver |
| * @mA: specifies the current limit in 2mA unit |
| * |
| * Return codes: |
| * -EINVAL: If the gadget passed is NULL |
| * -EOPNOTSUPP: |
| */ |
| static int pch_udc_pcd_vbus_draw(struct usb_gadget *gadget, unsigned int mA) |
| { |
| return -EOPNOTSUPP; |
| } |
| |
| static int pch_udc_start(struct usb_gadget *g, |
| struct usb_gadget_driver *driver); |
| static int pch_udc_stop(struct usb_gadget *g); |
| |
| static const struct usb_gadget_ops pch_udc_ops = { |
| .get_frame = pch_udc_pcd_get_frame, |
| .wakeup = pch_udc_pcd_wakeup, |
| .set_selfpowered = pch_udc_pcd_selfpowered, |
| .pullup = pch_udc_pcd_pullup, |
| .vbus_session = pch_udc_pcd_vbus_session, |
| .vbus_draw = pch_udc_pcd_vbus_draw, |
| .udc_start = pch_udc_start, |
| .udc_stop = pch_udc_stop, |
| }; |
| |
| /** |
| * pch_vbus_gpio_get_value() - This API gets value of GPIO port as VBUS status. |
| * @dev: Reference to the driver structure |
| * |
| * Return value: |
| * 1: VBUS is high |
| * 0: VBUS is low |
| * -1: It is not enable to detect VBUS using GPIO |
| */ |
| static int pch_vbus_gpio_get_value(struct pch_udc_dev *dev) |
| { |
| int vbus = 0; |
| |
| if (dev->vbus_gpio.port) |
| vbus = gpio_get_value(dev->vbus_gpio.port) ? 1 : 0; |
| else |
| vbus = -1; |
| |
| return vbus; |
| } |
| |
| /** |
| * pch_vbus_gpio_work_fall() - This API keeps watch on VBUS becoming Low. |
| * If VBUS is Low, disconnect is processed |
| * @irq_work: Structure for WorkQueue |
| * |
| */ |
| static void pch_vbus_gpio_work_fall(struct work_struct *irq_work) |
| { |
| struct pch_vbus_gpio_data *vbus_gpio = container_of(irq_work, |
| struct pch_vbus_gpio_data, irq_work_fall); |
| struct pch_udc_dev *dev = |
| container_of(vbus_gpio, struct pch_udc_dev, vbus_gpio); |
| int vbus_saved = -1; |
| int vbus; |
| int count; |
| |
| if (!dev->vbus_gpio.port) |
| return; |
| |
| for (count = 0; count < (PCH_VBUS_PERIOD / PCH_VBUS_INTERVAL); |
| count++) { |
| vbus = pch_vbus_gpio_get_value(dev); |
| |
| if ((vbus_saved == vbus) && (vbus == 0)) { |
| dev_dbg(&dev->pdev->dev, "VBUS fell"); |
| if (dev->driver |
| && dev->driver->disconnect) { |
| dev->driver->disconnect( |
| &dev->gadget); |
| } |
| if (dev->vbus_gpio.intr) |
| pch_udc_init(dev); |
| else |
| pch_udc_reconnect(dev); |
| return; |
| } |
| vbus_saved = vbus; |
| mdelay(PCH_VBUS_INTERVAL); |
| } |
| } |
| |
| /** |
| * pch_vbus_gpio_work_rise() - This API checks VBUS is High. |
| * If VBUS is High, connect is processed |
| * @irq_work: Structure for WorkQueue |
| * |
| */ |
| static void pch_vbus_gpio_work_rise(struct work_struct *irq_work) |
| { |
| struct pch_vbus_gpio_data *vbus_gpio = container_of(irq_work, |
| struct pch_vbus_gpio_data, irq_work_rise); |
| struct pch_udc_dev *dev = |
| container_of(vbus_gpio, struct pch_udc_dev, vbus_gpio); |
| int vbus; |
| |
| if (!dev->vbus_gpio.port) |
| return; |
| |
| mdelay(PCH_VBUS_INTERVAL); |
| vbus = pch_vbus_gpio_get_value(dev); |
| |
| if (vbus == 1) { |
| dev_dbg(&dev->pdev->dev, "VBUS rose"); |
| pch_udc_reconnect(dev); |
| return; |
| } |
| } |
| |
| /** |
| * pch_vbus_gpio_irq() - IRQ handler for GPIO intrerrupt for changing VBUS |
| * @irq: Interrupt request number |
| * @dev: Reference to the device structure |
| * |
| * Return codes: |
| * 0: Success |
| * -EINVAL: GPIO port is invalid or can't be initialized. |
| */ |
| static irqreturn_t pch_vbus_gpio_irq(int irq, void *data) |
| { |
| struct pch_udc_dev *dev = (struct pch_udc_dev *)data; |
| |
| if (!dev->vbus_gpio.port || !dev->vbus_gpio.intr) |
| return IRQ_NONE; |
| |
| if (pch_vbus_gpio_get_value(dev)) |
| schedule_work(&dev->vbus_gpio.irq_work_rise); |
| else |
| schedule_work(&dev->vbus_gpio.irq_work_fall); |
| |
| return IRQ_HANDLED; |
| } |
| |
| /** |
| * pch_vbus_gpio_init() - This API initializes GPIO port detecting VBUS. |
| * @dev: Reference to the driver structure |
| * @vbus_gpio Number of GPIO port to detect gpio |
| * |
| * Return codes: |
| * 0: Success |
| * -EINVAL: GPIO port is invalid or can't be initialized. |
| */ |
| static int pch_vbus_gpio_init(struct pch_udc_dev *dev, int vbus_gpio_port) |
| { |
| int err; |
| int irq_num = 0; |
| |
| dev->vbus_gpio.port = 0; |
| dev->vbus_gpio.intr = 0; |
| |
| if (vbus_gpio_port <= -1) |
| return -EINVAL; |
| |
| err = gpio_is_valid(vbus_gpio_port); |
| if (!err) { |
| pr_err("%s: gpio port %d is invalid\n", |
| __func__, vbus_gpio_port); |
| return -EINVAL; |
| } |
| |
| err = gpio_request(vbus_gpio_port, "pch_vbus"); |
| if (err) { |
| pr_err("%s: can't request gpio port %d, err: %d\n", |
| __func__, vbus_gpio_port, err); |
| return -EINVAL; |
| } |
| |
| dev->vbus_gpio.port = vbus_gpio_port; |
| gpio_direction_input(vbus_gpio_port); |
| INIT_WORK(&dev->vbus_gpio.irq_work_fall, pch_vbus_gpio_work_fall); |
| |
| irq_num = gpio_to_irq(vbus_gpio_port); |
| if (irq_num > 0) { |
| irq_set_irq_type(irq_num, IRQ_TYPE_EDGE_BOTH); |
| err = request_irq(irq_num, pch_vbus_gpio_irq, 0, |
| "vbus_detect", dev); |
| if (!err) { |
| dev->vbus_gpio.intr = irq_num; |
| INIT_WORK(&dev->vbus_gpio.irq_work_rise, |
| pch_vbus_gpio_work_rise); |
| } else { |
| pr_err("%s: can't request irq %d, err: %d\n", |
| __func__, irq_num, err); |
| } |
| } |
| |
| return 0; |
| } |
| |
| /** |
| * pch_vbus_gpio_free() - This API frees resources of GPIO port |
| * @dev: Reference to the driver structure |
| */ |
| static void pch_vbus_gpio_free(struct pch_udc_dev *dev) |
| { |
| if (dev->vbus_gpio.intr) |
| free_irq(dev->vbus_gpio.intr, dev); |
| |
| if (dev->vbus_gpio.port) |
| gpio_free(dev->vbus_gpio.port); |
| } |
| |
| /** |
| * complete_req() - This API is invoked from the driver when processing |
| * of a request is complete |
| * @ep: Reference to the endpoint structure |
| * @req: Reference to the request structure |
| * @status: Indicates the success/failure of completion |
| */ |
| static void complete_req(struct pch_udc_ep *ep, struct pch_udc_request *req, |
| int status) |
| __releases(&dev->lock) |
| __acquires(&dev->lock) |
| { |
| struct pch_udc_dev *dev; |
| unsigned halted = ep->halted; |
| |
| list_del_init(&req->queue); |
| |
| /* set new status if pending */ |
| if (req->req.status == -EINPROGRESS) |
| req->req.status = status; |
| else |
| status = req->req.status; |
| |
| dev = ep->dev; |
| if (req->dma_mapped) { |
| if (req->dma == DMA_ADDR_INVALID) { |
| if (ep->in) |
| dma_unmap_single(&dev->pdev->dev, req->req.dma, |
| req->req.length, |
| DMA_TO_DEVICE); |
| else |
| dma_unmap_single(&dev->pdev->dev, req->req.dma, |
| req->req.length, |
| DMA_FROM_DEVICE); |
| req->req.dma = DMA_ADDR_INVALID; |
| } else { |
| if (ep->in) |
| dma_unmap_single(&dev->pdev->dev, req->dma, |
| req->req.length, |
| DMA_TO_DEVICE); |
| else { |
| dma_unmap_single(&dev->pdev->dev, req->dma, |
| req->req.length, |
| DMA_FROM_DEVICE); |
| memcpy(req->req.buf, req->buf, req->req.length); |
| } |
| kfree(req->buf); |
| req->dma = DMA_ADDR_INVALID; |
| } |
| req->dma_mapped = 0; |
| } |
| ep->halted = 1; |
| spin_unlock(&dev->lock); |
| if (!ep->in) |
| pch_udc_ep_clear_rrdy(ep); |
| usb_gadget_giveback_request(&ep->ep, &req->req); |
| spin_lock(&dev->lock); |
| ep->halted = halted; |
| } |
| |
| /** |
| * empty_req_queue() - This API empties the request queue of an endpoint |
| * @ep: Reference to the endpoint structure |
| */ |
| static void empty_req_queue(struct pch_udc_ep *ep) |
| { |
| struct pch_udc_request *req; |
| |
| ep->halted = 1; |
| while (!list_empty(&ep->queue)) { |
| req = list_entry(ep->queue.next, struct pch_udc_request, queue); |
| complete_req(ep, req, -ESHUTDOWN); /* Remove from list */ |
| } |
| } |
| |
| /** |
| * pch_udc_free_dma_chain() - This function frees the DMA chain created |
| * for the request |
| * @dev Reference to the driver structure |
| * @req Reference to the request to be freed |
| * |
| * Return codes: |
| * 0: Success |
| */ |
| static void pch_udc_free_dma_chain(struct pch_udc_dev *dev, |
| struct pch_udc_request *req) |
| { |
| struct pch_udc_data_dma_desc *td = req->td_data; |
| unsigned i = req->chain_len; |
| |
| dma_addr_t addr2; |
| dma_addr_t addr = (dma_addr_t)td->next; |
| td->next = 0x00; |
| for (; i > 1; --i) { |
| /* do not free first desc., will be done by free for request */ |
| td = phys_to_virt(addr); |
| addr2 = (dma_addr_t)td->next; |
| pci_pool_free(dev->data_requests, td, addr); |
| td->next = 0x00; |
| addr = addr2; |
| } |
| req->chain_len = 1; |
| } |
| |
| /** |
| * pch_udc_create_dma_chain() - This function creates or reinitializes |
| * a DMA chain |
| * @ep: Reference to the endpoint structure |
| * @req: Reference to the request |
| * @buf_len: The buffer length |
| * @gfp_flags: Flags to be used while mapping the data buffer |
| * |
| * Return codes: |
| * 0: success, |
| * -ENOMEM: pci_pool_alloc invocation fails |
| */ |
| static int pch_udc_create_dma_chain(struct pch_udc_ep *ep, |
| struct pch_udc_request *req, |
| unsigned long buf_len, |
| gfp_t gfp_flags) |
| { |
| struct pch_udc_data_dma_desc *td = req->td_data, *last; |
| unsigned long bytes = req->req.length, i = 0; |
| dma_addr_t dma_addr; |
| unsigned len = 1; |
| |
| if (req->chain_len > 1) |
| pch_udc_free_dma_chain(ep->dev, req); |
| |
| if (req->dma == DMA_ADDR_INVALID) |
| td->dataptr = req->req.dma; |
| else |
| td->dataptr = req->dma; |
| |
| td->status = PCH_UDC_BS_HST_BSY; |
| for (; ; bytes -= buf_len, ++len) { |
| td->status = PCH_UDC_BS_HST_BSY | min(buf_len, bytes); |
| if (bytes <= buf_len) |
| break; |
| last = td; |
| td = pci_pool_alloc(ep->dev->data_requests, gfp_flags, |
| &dma_addr); |
| if (!td) |
| goto nomem; |
| i += buf_len; |
| td->dataptr = req->td_data->dataptr + i; |
| last->next = dma_addr; |
| } |
| |
| req->td_data_last = td; |
| td->status |= PCH_UDC_DMA_LAST; |
| td->next = req->td_data_phys; |
| req->chain_len = len; |
| return 0; |
| |
| nomem: |
| if (len > 1) { |
| req->chain_len = len; |
| pch_udc_free_dma_chain(ep->dev, req); |
| } |
| req->chain_len = 1; |
| return -ENOMEM; |
| } |
| |
| /** |
| * prepare_dma() - This function creates and initializes the DMA chain |
| * for the request |
| * @ep: Reference to the endpoint structure |
| * @req: Reference to the request |
| * @gfp: Flag to be used while mapping the data buffer |
| * |
| * Return codes: |
| * 0: Success |
| * Other 0: linux error number on failure |
| */ |
| static int prepare_dma(struct pch_udc_ep *ep, struct pch_udc_request *req, |
| gfp_t gfp) |
| { |
| int retval; |
| |
| /* Allocate and create a DMA chain */ |
| retval = pch_udc_create_dma_chain(ep, req, ep->ep.maxpacket, gfp); |
| if (retval) { |
| pr_err("%s: could not create DMA chain:%d\n", __func__, retval); |
| return retval; |
| } |
| if (ep->in) |
| req->td_data->status = (req->td_data->status & |
| ~PCH_UDC_BUFF_STS) | PCH_UDC_BS_HST_RDY; |
| return 0; |
| } |
| |
| /** |
| * process_zlp() - This function process zero length packets |
| * from the gadget driver |
| * @ep: Reference to the endpoint structure |
| * @req: Reference to the request |
| */ |
| static void process_zlp(struct pch_udc_ep *ep, struct pch_udc_request *req) |
| { |
| struct pch_udc_dev *dev = ep->dev; |
| |
| /* IN zlp's are handled by hardware */ |
| complete_req(ep, req, 0); |
| |
| /* if set_config or set_intf is waiting for ack by zlp |
| * then set CSR_DONE |
| */ |
| if (dev->set_cfg_not_acked) { |
| pch_udc_set_csr_done(dev); |
| dev->set_cfg_not_acked = 0; |
| } |
| /* setup command is ACK'ed now by zlp */ |
| if (!dev->stall && dev->waiting_zlp_ack) { |
| pch_udc_ep_clear_nak(&(dev->ep[UDC_EP0IN_IDX])); |
| dev->waiting_zlp_ack = 0; |
| } |
| } |
| |
| /** |
| * pch_udc_start_rxrequest() - This function starts the receive requirement. |
| * @ep: Reference to the endpoint structure |
| * @req: Reference to the request structure |
| */ |
| static void pch_udc_start_rxrequest(struct pch_udc_ep *ep, |
| struct pch_udc_request *req) |
| { |
| struct pch_udc_data_dma_desc *td_data; |
| |
| pch_udc_clear_dma(ep->dev, DMA_DIR_RX); |
| td_data = req->td_data; |
| /* Set the status bits for all descriptors */ |
| while (1) { |
| td_data->status = (td_data->status & ~PCH_UDC_BUFF_STS) | |
| PCH_UDC_BS_HST_RDY; |
| if ((td_data->status & PCH_UDC_DMA_LAST) == PCH_UDC_DMA_LAST) |
| break; |
| td_data = phys_to_virt(td_data->next); |
| } |
| /* Write the descriptor pointer */ |
| pch_udc_ep_set_ddptr(ep, req->td_data_phys); |
| req->dma_going = 1; |
| pch_udc_enable_ep_interrupts(ep->dev, UDC_EPINT_OUT_EP0 << ep->num); |
| pch_udc_set_dma(ep->dev, DMA_DIR_RX); |
| pch_udc_ep_clear_nak(ep); |
| pch_udc_ep_set_rrdy(ep); |
| } |
| |
| /** |
| * pch_udc_pcd_ep_enable() - This API enables the endpoint. It is called |
| * from gadget driver |
| * @usbep: Reference to the USB endpoint structure |
| * @desc: Reference to the USB endpoint descriptor structure |
| * |
| * Return codes: |
| * 0: Success |
| * -EINVAL: |
| * -ESHUTDOWN: |
| */ |
| static int pch_udc_pcd_ep_enable(struct usb_ep *usbep, |
| const struct usb_endpoint_descriptor *desc) |
| { |
| struct pch_udc_ep *ep; |
| struct pch_udc_dev *dev; |
| unsigned long iflags; |
| |
| if (!usbep || (usbep->name == ep0_string) || !desc || |
| (desc->bDescriptorType != USB_DT_ENDPOINT) || !desc->wMaxPacketSize) |
| return -EINVAL; |
| |
| ep = container_of(usbep, struct pch_udc_ep, ep); |
| dev = ep->dev; |
| if (!dev->driver || (dev->gadget.speed == USB_SPEED_UNKNOWN)) |
| return -ESHUTDOWN; |
| spin_lock_irqsave(&dev->lock, iflags); |
| ep->ep.desc = desc; |
| ep->halted = 0; |
| pch_udc_ep_enable(ep, &ep->dev->cfg_data, desc); |
| ep->ep.maxpacket = usb_endpoint_maxp(desc); |
| pch_udc_enable_ep_interrupts(ep->dev, PCH_UDC_EPINT(ep->in, ep->num)); |
| spin_unlock_irqrestore(&dev->lock, iflags); |
| return 0; |
| } |
| |
| /** |
| * pch_udc_pcd_ep_disable() - This API disables endpoint and is called |
| * from gadget driver |
| * @usbep Reference to the USB endpoint structure |
| * |
| * Return codes: |
| * 0: Success |
| * -EINVAL: |
| */ |
| static int pch_udc_pcd_ep_disable(struct usb_ep *usbep) |
| { |
| struct pch_udc_ep *ep; |
| struct pch_udc_dev *dev; |
| unsigned long iflags; |
| |
| if (!usbep) |
| return -EINVAL; |
| |
| ep = container_of(usbep, struct pch_udc_ep, ep); |
| dev = ep->dev; |
| if ((usbep->name == ep0_string) || !ep->ep.desc) |
| return -EINVAL; |
| |
| spin_lock_irqsave(&ep->dev->lock, iflags); |
| empty_req_queue(ep); |
| ep->halted = 1; |
| pch_udc_ep_disable(ep); |
| pch_udc_disable_ep_interrupts(ep->dev, PCH_UDC_EPINT(ep->in, ep->num)); |
| ep->ep.desc = NULL; |
| INIT_LIST_HEAD(&ep->queue); |
| spin_unlock_irqrestore(&ep->dev->lock, iflags); |
| return 0; |
| } |
| |
| /** |
| * pch_udc_alloc_request() - This function allocates request structure. |
| * It is called by gadget driver |
| * @usbep: Reference to the USB endpoint structure |
| * @gfp: Flag to be used while allocating memory |
| * |
| * Return codes: |
| * NULL: Failure |
| * Allocated address: Success |
| */ |
| static struct usb_request *pch_udc_alloc_request(struct usb_ep *usbep, |
| gfp_t gfp) |
| { |
| struct pch_udc_request *req; |
| struct pch_udc_ep *ep; |
| struct pch_udc_data_dma_desc *dma_desc; |
| struct pch_udc_dev *dev; |
| |
| if (!usbep) |
| return NULL; |
| ep = container_of(usbep, struct pch_udc_ep, ep); |
| dev = ep->dev; |
| req = kzalloc(sizeof *req, gfp); |
| if (!req) |
| return NULL; |
| req->req.dma = DMA_ADDR_INVALID; |
| req->dma = DMA_ADDR_INVALID; |
| INIT_LIST_HEAD(&req->queue); |
| if (!ep->dev->dma_addr) |
| return &req->req; |
| /* ep0 in requests are allocated from data pool here */ |
| dma_desc = pci_pool_alloc(ep->dev->data_requests, gfp, |
| &req->td_data_phys); |
| if (NULL == dma_desc) { |
| kfree(req); |
| return NULL; |
| } |
| /* prevent from using desc. - set HOST BUSY */ |
| dma_desc->status |= PCH_UDC_BS_HST_BSY; |
| dma_desc->dataptr = __constant_cpu_to_le32(DMA_ADDR_INVALID); |
| req->td_data = dma_desc; |
| req->td_data_last = dma_desc; |
| req->chain_len = 1; |
| return &req->req; |
| } |
| |
| /** |
| * pch_udc_free_request() - This function frees request structure. |
| * It is called by gadget driver |
| * @usbep: Reference to the USB endpoint structure |
| * @usbreq: Reference to the USB request |
| */ |
| static void pch_udc_free_request(struct usb_ep *usbep, |
| struct usb_request *usbreq) |
| { |
| struct pch_udc_ep *ep; |
| struct pch_udc_request *req; |
| struct pch_udc_dev *dev; |
| |
| if (!usbep || !usbreq) |
| return; |
| ep = container_of(usbep, struct pch_udc_ep, ep); |
| req = container_of(usbreq, struct pch_udc_request, req); |
| dev = ep->dev; |
| if (!list_empty(&req->queue)) |
| dev_err(&dev->pdev->dev, "%s: %s req=0x%p queue not empty\n", |
| __func__, usbep->name, req); |
| if (req->td_data != NULL) { |
| if (req->chain_len > 1) |
| pch_udc_free_dma_chain(ep->dev, req); |
| pci_pool_free(ep->dev->data_requests, req->td_data, |
| req->td_data_phys); |
| } |
| kfree(req); |
| } |
| |
| /** |
| * pch_udc_pcd_queue() - This function queues a request packet. It is called |
| * by gadget driver |
| * @usbep: Reference to the USB endpoint structure |
| * @usbreq: Reference to the USB request |
| * @gfp: Flag to be used while mapping the data buffer |
| * |
| * Return codes: |
| * 0: Success |
| * linux error number: Failure |
| */ |
| static int pch_udc_pcd_queue(struct usb_ep *usbep, struct usb_request *usbreq, |
| gfp_t gfp) |
| { |
| int retval = 0; |
| struct pch_udc_ep *ep; |
| struct pch_udc_dev *dev; |
| struct pch_udc_request *req; |
| unsigned long iflags; |
| |
| if (!usbep || !usbreq || !usbreq->complete || !usbreq->buf) |
| return -EINVAL; |
| ep = container_of(usbep, struct pch_udc_ep, ep); |
| dev = ep->dev; |
| if (!ep->ep.desc && ep->num) |
| return -EINVAL; |
| req = container_of(usbreq, struct pch_udc_request, req); |
| if (!list_empty(&req->queue)) |
| return -EINVAL; |
| if (!dev->driver || (dev->gadget.speed == USB_SPEED_UNKNOWN)) |
| return -ESHUTDOWN; |
| spin_lock_irqsave(&dev->lock, iflags); |
| /* map the buffer for dma */ |
| if (usbreq->length && |
| ((usbreq->dma == DMA_ADDR_INVALID) || !usbreq->dma)) { |
| if (!((unsigned long)(usbreq->buf) & 0x03)) { |
| if (ep->in) |
| usbreq->dma = dma_map_single(&dev->pdev->dev, |
| usbreq->buf, |
| usbreq->length, |
| DMA_TO_DEVICE); |
| else |
| usbreq->dma = dma_map_single(&dev->pdev->dev, |
| usbreq->buf, |
| usbreq->length, |
| DMA_FROM_DEVICE); |
| } else { |
| req->buf = kzalloc(usbreq->length, GFP_ATOMIC); |
| if (!req->buf) { |
| retval = -ENOMEM; |
| goto probe_end; |
| } |
| if (ep->in) { |
| memcpy(req->buf, usbreq->buf, usbreq->length); |
| req->dma = dma_map_single(&dev->pdev->dev, |
| req->buf, |
| usbreq->length, |
| DMA_TO_DEVICE); |
| } else |
| req->dma = dma_map_single(&dev->pdev->dev, |
| req->buf, |
| usbreq->length, |
| DMA_FROM_DEVICE); |
| } |
| req->dma_mapped = 1; |
| } |
| if (usbreq->length > 0) { |
| retval = prepare_dma(ep, req, GFP_ATOMIC); |
| if (retval) |
| goto probe_end; |
| } |
| usbreq->actual = 0; |
| usbreq->status = -EINPROGRESS; |
| req->dma_done = 0; |
| if (list_empty(&ep->queue) && !ep->halted) { |
| /* no pending transfer, so start this req */ |
| if (!usbreq->length) { |
| process_zlp(ep, req); |
| retval = 0; |
| goto probe_end; |
| } |
| if (!ep->in) { |
| pch_udc_start_rxrequest(ep, req); |
| } else { |
| /* |
| * For IN trfr the descriptors will be programmed and |
| * P bit will be set when |
| * we get an IN token |
| */ |
| pch_udc_wait_ep_stall(ep); |
| pch_udc_ep_clear_nak(ep); |
| pch_udc_enable_ep_interrupts(ep->dev, (1 << ep->num)); |
| } |
| } |
| /* Now add this request to the ep's pending requests */ |
| if (req != NULL) |
| list_add_tail(&req->queue, &ep->queue); |
| |
| probe_end: |
| spin_unlock_irqrestore(&dev->lock, iflags); |
| return retval; |
| } |
| |
| /** |
| * pch_udc_pcd_dequeue() - This function de-queues a request packet. |
| * It is called by gadget driver |
| * @usbep: Reference to the USB endpoint structure |
| * @usbreq: Reference to the USB request |
| * |
| * Return codes: |
| * 0: Success |
| * linux error number: Failure |
| */ |
| static int pch_udc_pcd_dequeue(struct usb_ep *usbep, |
| struct usb_request *usbreq) |
| { |
| struct pch_udc_ep *ep; |
| struct pch_udc_request *req; |
| struct pch_udc_dev *dev; |
| unsigned long flags; |
| int ret = -EINVAL; |
| |
| ep = container_of(usbep, struct pch_udc_ep, ep); |
| dev = ep->dev; |
| if (!usbep || !usbreq || (!ep->ep.desc && ep->num)) |
| return ret; |
| req = container_of(usbreq, struct pch_udc_request, req); |
| spin_lock_irqsave(&ep->dev->lock, flags); |
| /* make sure it's still queued on this endpoint */ |
| list_for_each_entry(req, &ep->queue, queue) { |
| if (&req->req == usbreq) { |
| pch_udc_ep_set_nak(ep); |
| if (!list_empty(&req->queue)) |
| complete_req(ep, req, -ECONNRESET); |
| ret = 0; |
| break; |
| } |
| } |
| spin_unlock_irqrestore(&ep->dev->lock, flags); |
| return ret; |
| } |
| |
| /** |
| * pch_udc_pcd_set_halt() - This function Sets or clear the endpoint halt |
| * feature |
| * @usbep: Reference to the USB endpoint structure |
| * @halt: Specifies whether to set or clear the feature |
| * |
| * Return codes: |
| * 0: Success |
| * linux error number: Failure |
| */ |
| static int pch_udc_pcd_set_halt(struct usb_ep *usbep, int halt) |
| { |
| struct pch_udc_ep *ep; |
| struct pch_udc_dev *dev; |
| unsigned long iflags; |
| int ret; |
| |
| if (!usbep) |
| return -EINVAL; |
| ep = container_of(usbep, struct pch_udc_ep, ep); |
| dev = ep->dev; |
| if (!ep->ep.desc && !ep->num) |
| return -EINVAL; |
| if (!ep->dev->driver || (ep->dev->gadget.speed == USB_SPEED_UNKNOWN)) |
| return -ESHUTDOWN; |
| spin_lock_irqsave(&udc_stall_spinlock, iflags); |
| if (list_empty(&ep->queue)) { |
| if (halt) { |
| if (ep->num == PCH_UDC_EP0) |
| ep->dev->stall = 1; |
| pch_udc_ep_set_stall(ep); |
| pch_udc_enable_ep_interrupts(ep->dev, |
| PCH_UDC_EPINT(ep->in, |
| ep->num)); |
| } else { |
| pch_udc_ep_clear_stall(ep); |
| } |
| ret = 0; |
| } else { |
| ret = -EAGAIN; |
| } |
| spin_unlock_irqrestore(&udc_stall_spinlock, iflags); |
| return ret; |
| } |
| |
| /** |
| * pch_udc_pcd_set_wedge() - This function Sets or clear the endpoint |
| * halt feature |
| * @usbep: Reference to the USB endpoint structure |
| * @halt: Specifies whether to set or clear the feature |
| * |
| * Return codes: |
| * 0: Success |
| * linux error number: Failure |
| */ |
| static int pch_udc_pcd_set_wedge(struct usb_ep *usbep) |
| { |
| struct pch_udc_ep *ep; |
| struct pch_udc_dev *dev; |
| unsigned long iflags; |
| int ret; |
| |
| if (!usbep) |
| return -EINVAL; |
| ep = container_of(usbep, struct pch_udc_ep, ep); |
| dev = ep->dev; |
| if (!ep->ep.desc && !ep->num) |
| return -EINVAL; |
| if (!ep->dev->driver || (ep->dev->gadget.speed == USB_SPEED_UNKNOWN)) |
| return -ESHUTDOWN; |
| spin_lock_irqsave(&udc_stall_spinlock, iflags); |
| if (!list_empty(&ep->queue)) { |
| ret = -EAGAIN; |
| } else { |
| if (ep->num == PCH_UDC_EP0) |
| ep->dev->stall = 1; |
| pch_udc_ep_set_stall(ep); |
| pch_udc_enable_ep_interrupts(ep->dev, |
| PCH_UDC_EPINT(ep->in, ep->num)); |
| ep->dev->prot_stall = 1; |
| ret = 0; |
| } |
| spin_unlock_irqrestore(&udc_stall_spinlock, iflags); |
| return ret; |
| } |
| |
| /** |
| * pch_udc_pcd_fifo_flush() - This function Flush the FIFO of specified endpoint |
| * @usbep: Reference to the USB endpoint structure |
| */ |
| static void pch_udc_pcd_fifo_flush(struct usb_ep *usbep) |
| { |
| struct pch_udc_ep *ep; |
| |
| if (!usbep) |
| return; |
| |
| ep = container_of(usbep, struct pch_udc_ep, ep); |
| if (ep->ep.desc || !ep->num) |
| pch_udc_ep_fifo_flush(ep, ep->in); |
| } |
| |
| static const struct usb_ep_ops pch_udc_ep_ops = { |
| .enable = pch_udc_pcd_ep_enable, |
| .disable = pch_udc_pcd_ep_disable, |
| .alloc_request = pch_udc_alloc_request, |
| .free_request = pch_udc_free_request, |
| .queue = pch_udc_pcd_queue, |
| .dequeue = pch_udc_pcd_dequeue, |
| .set_halt = pch_udc_pcd_set_halt, |
| .set_wedge = pch_udc_pcd_set_wedge, |
| .fifo_status = NULL, |
| .fifo_flush = pch_udc_pcd_fifo_flush, |
| }; |
| |
| /** |
| * pch_udc_init_setup_buff() - This function initializes the SETUP buffer |
| * @td_stp: Reference to the SETP buffer structure |
| */ |
| static void pch_udc_init_setup_buff(struct pch_udc_stp_dma_desc *td_stp) |
| { |
| static u32 pky_marker; |
| |
| if (!td_stp) |
| return; |
| td_stp->reserved = ++pky_marker; |
| memset(&td_stp->request, 0xFF, sizeof td_stp->request); |
| td_stp->status = PCH_UDC_BS_HST_RDY; |
| } |
| |
| /** |
| * pch_udc_start_next_txrequest() - This function starts |
| * the next transmission requirement |
| * @ep: Reference to the endpoint structure |
| */ |
| static void pch_udc_start_next_txrequest(struct pch_udc_ep *ep) |
| { |
| struct pch_udc_request *req; |
| struct pch_udc_data_dma_desc *td_data; |
| |
| if (pch_udc_read_ep_control(ep) & UDC_EPCTL_P) |
| return; |
| |
| if (list_empty(&ep->queue)) |
| return; |
| |
| /* next request */ |
| req = list_entry(ep->queue.next, struct pch_udc_request, queue); |
| if (req->dma_going) |
| return; |
| if (!req->td_data) |
| return; |
| pch_udc_wait_ep_stall(ep); |
| req->dma_going = 1; |
| pch_udc_ep_set_ddptr(ep, 0); |
| td_data = req->td_data; |
| while (1) { |
| td_data->status = (td_data->status & ~PCH_UDC_BUFF_STS) | |
| PCH_UDC_BS_HST_RDY; |
| if ((td_data->status & PCH_UDC_DMA_LAST) == PCH_UDC_DMA_LAST) |
| break; |
| td_data = phys_to_virt(td_data->next); |
| } |
| pch_udc_ep_set_ddptr(ep, req->td_data_phys); |
| pch_udc_set_dma(ep->dev, DMA_DIR_TX); |
| pch_udc_ep_set_pd(ep); |
| pch_udc_enable_ep_interrupts(ep->dev, PCH_UDC_EPINT(ep->in, ep->num)); |
| pch_udc_ep_clear_nak(ep); |
| } |
| |
| /** |
| * pch_udc_complete_transfer() - This function completes a transfer |
| * @ep: Reference to the endpoint structure |
| */ |
| static void pch_udc_complete_transfer(struct pch_udc_ep *ep) |
| { |
| struct pch_udc_request *req; |
| struct pch_udc_dev *dev = ep->dev; |
| |
| if (list_empty(&ep->queue)) |
| return; |
| req = list_entry(ep->queue.next, struct pch_udc_request, queue); |
| if ((req->td_data_last->status & PCH_UDC_BUFF_STS) != |
| PCH_UDC_BS_DMA_DONE) |
| return; |
| if ((req->td_data_last->status & PCH_UDC_RXTX_STS) != |
| PCH_UDC_RTS_SUCC) { |
| dev_err(&dev->pdev->dev, "Invalid RXTX status (0x%08x) " |
| "epstatus=0x%08x\n", |
| (req->td_data_last->status & PCH_UDC_RXTX_STS), |
| (int)(ep->epsts)); |
| return; |
| } |
| |
| req->req.actual = req->req.length; |
| req->td_data_last->status = PCH_UDC_BS_HST_BSY | PCH_UDC_DMA_LAST; |
| req->td_data->status = PCH_UDC_BS_HST_BSY | PCH_UDC_DMA_LAST; |
| complete_req(ep, req, 0); |
| req->dma_going = 0; |
| if (!list_empty(&ep->queue)) { |
| pch_udc_wait_ep_stall(ep); |
| pch_udc_ep_clear_nak(ep); |
| pch_udc_enable_ep_interrupts(ep->dev, |
| PCH_UDC_EPINT(ep->in, ep->num)); |
| } else { |
| pch_udc_disable_ep_interrupts(ep->dev, |
| PCH_UDC_EPINT(ep->in, ep->num)); |
| } |
| } |
| |
| /** |
| * pch_udc_complete_receiver() - This function completes a receiver |
| * @ep: Reference to the endpoint structure |
| */ |
| static void pch_udc_complete_receiver(struct pch_udc_ep *ep) |
| { |
| struct pch_udc_request *req; |
| struct pch_udc_dev *dev = ep->dev; |
| unsigned int count; |
| struct pch_udc_data_dma_desc *td; |
| dma_addr_t addr; |
| |
| if (list_empty(&ep->queue)) |
| return; |
| /* next request */ |
| req = list_entry(ep->queue.next, struct pch_udc_request, queue); |
| pch_udc_clear_dma(ep->dev, DMA_DIR_RX); |
| pch_udc_ep_set_ddptr(ep, 0); |
| if ((req->td_data_last->status & PCH_UDC_BUFF_STS) == |
| PCH_UDC_BS_DMA_DONE) |
| td = req->td_data_last; |
| else |
| td = req->td_data; |
| |
| while (1) { |
| if ((td->status & PCH_UDC_RXTX_STS) != PCH_UDC_RTS_SUCC) { |
| dev_err(&dev->pdev->dev, "Invalid RXTX status=0x%08x " |
| "epstatus=0x%08x\n", |
| (req->td_data->status & PCH_UDC_RXTX_STS), |
| (int)(ep->epsts)); |
| return; |
| } |
| if ((td->status & PCH_UDC_BUFF_STS) == PCH_UDC_BS_DMA_DONE) |
| if (td->status & PCH_UDC_DMA_LAST) { |
| count = td->status & PCH_UDC_RXTX_BYTES; |
| break; |
| } |
| if (td == req->td_data_last) { |
| dev_err(&dev->pdev->dev, "Not complete RX descriptor"); |
| return; |
| } |
| addr = (dma_addr_t)td->next; |
| td = phys_to_virt(addr); |
| } |
| /* on 64k packets the RXBYTES field is zero */ |
| if (!count && (req->req.length == UDC_DMA_MAXPACKET)) |
| count = UDC_DMA_MAXPACKET; |
| req->td_data->status |= PCH_UDC_DMA_LAST; |
| td->status |= PCH_UDC_BS_HST_BSY; |
| |
| req->dma_going = 0; |
| req->req.actual = count; |
| complete_req(ep, req, 0); |
| /* If there is a new/failed requests try that now */ |
| if (!list_empty(&ep->queue)) { |
| req = list_entry(ep->queue.next, struct pch_udc_request, queue); |
| pch_udc_start_rxrequest(ep, req); |
| } |
| } |
| |
| /** |
| * pch_udc_svc_data_in() - This function process endpoint interrupts |
| * for IN endpoints |
| * @dev: Reference to the device structure |
| * @ep_num: Endpoint that generated the interrupt |
| */ |
| static void pch_udc_svc_data_in(struct pch_udc_dev *dev, int ep_num) |
| { |
| u32 epsts; |
| struct pch_udc_ep *ep; |
| |
| ep = &dev->ep[UDC_EPIN_IDX(ep_num)]; |
| epsts = ep->epsts; |
| ep->epsts = 0; |
| |
| if (!(epsts & (UDC_EPSTS_IN | UDC_EPSTS_BNA | UDC_EPSTS_HE | |
| UDC_EPSTS_TDC | UDC_EPSTS_RCS | UDC_EPSTS_TXEMPTY | |
| UDC_EPSTS_RSS | UDC_EPSTS_XFERDONE))) |
| return; |
| if ((epsts & UDC_EPSTS_BNA)) |
| return; |
| if (epsts & UDC_EPSTS_HE) |
| return; |
| if (epsts & UDC_EPSTS_RSS) { |
| pch_udc_ep_set_stall(ep); |
| pch_udc_enable_ep_interrupts(ep->dev, |
| PCH_UDC_EPINT(ep->in, ep->num)); |
| } |
| if (epsts & UDC_EPSTS_RCS) { |
| if (!dev->prot_stall) { |
| pch_udc_ep_clear_stall(ep); |
| } else { |
| pch_udc_ep_set_stall(ep); |
| pch_udc_enable_ep_interrupts(ep->dev, |
| PCH_UDC_EPINT(ep->in, ep->num)); |
| } |
| } |
| if (epsts & UDC_EPSTS_TDC) |
| pch_udc_complete_transfer(ep); |
| /* On IN interrupt, provide data if we have any */ |
| if ((epsts & UDC_EPSTS_IN) && !(epsts & UDC_EPSTS_RSS) && |
| !(epsts & UDC_EPSTS_TDC) && !(epsts & UDC_EPSTS_TXEMPTY)) |
| pch_udc_start_next_txrequest(ep); |
| } |
| |
| /** |
| * pch_udc_svc_data_out() - Handles interrupts from OUT endpoint |
| * @dev: Reference to the device structure |
| * @ep_num: Endpoint that generated the interrupt |
| */ |
| static void pch_udc_svc_data_out(struct pch_udc_dev *dev, int ep_num) |
| { |
| u32 epsts; |
| struct pch_udc_ep *ep; |
| struct pch_udc_request *req = NULL; |
| |
| ep = &dev->ep[UDC_EPOUT_IDX(ep_num)]; |
| epsts = ep->epsts; |
| ep->epsts = 0; |
| |
| if ((epsts & UDC_EPSTS_BNA) && (!list_empty(&ep->queue))) { |
| /* next request */ |
| req = list_entry(ep->queue.next, struct pch_udc_request, |
| queue); |
| if ((req->td_data_last->status & PCH_UDC_BUFF_STS) != |
| PCH_UDC_BS_DMA_DONE) { |
| if (!req->dma_going) |
| pch_udc_start_rxrequest(ep, req); |
| return; |
| } |
| } |
| if (epsts & UDC_EPSTS_HE) |
| return; |
| if (epsts & UDC_EPSTS_RSS) { |
| pch_udc_ep_set_stall(ep); |
| pch_udc_enable_ep_interrupts(ep->dev, |
| PCH_UDC_EPINT(ep->in, ep->num)); |
| } |
| if (epsts & UDC_EPSTS_RCS) { |
| if (!dev->prot_stall) { |
| pch_udc_ep_clear_stall(ep); |
| } else { |
| pch_udc_ep_set_stall(ep); |
| pch_udc_enable_ep_interrupts(ep->dev, |
| PCH_UDC_EPINT(ep->in, ep->num)); |
| } |
| } |
| if (((epsts & UDC_EPSTS_OUT_MASK) >> UDC_EPSTS_OUT_SHIFT) == |
| UDC_EPSTS_OUT_DATA) { |
| if (ep->dev->prot_stall == 1) { |
| pch_udc_ep_set_stall(ep); |
| pch_udc_enable_ep_interrupts(ep->dev, |
| PCH_UDC_EPINT(ep->in, ep->num)); |
| } else { |
| pch_udc_complete_receiver(ep); |
| } |
| } |
| if (list_empty(&ep->queue)) |
| pch_udc_set_dma(dev, DMA_DIR_RX); |
| } |
| |
| /** |
| * pch_udc_svc_control_in() - Handle Control IN endpoint interrupts |
| * @dev: Reference to the device structure |
| */ |
| static void pch_udc_svc_control_in(struct pch_udc_dev *dev) |
| { |
| u32 epsts; |
| struct pch_udc_ep *ep; |
| struct pch_udc_ep *ep_out; |
| |
| ep = &dev->ep[UDC_EP0IN_IDX]; |
| ep_out = &dev->ep[UDC_EP0OUT_IDX]; |
| epsts = ep->epsts; |
| ep->epsts = 0; |
| |
| if (!(epsts & (UDC_EPSTS_IN | UDC_EPSTS_BNA | UDC_EPSTS_HE | |
| UDC_EPSTS_TDC | UDC_EPSTS_RCS | UDC_EPSTS_TXEMPTY | |
| UDC_EPSTS_XFERDONE))) |
| return; |
| if ((epsts & UDC_EPSTS_BNA)) |
| return; |
| if (epsts & UDC_EPSTS_HE) |
| return; |
| if ((epsts & UDC_EPSTS_TDC) && (!dev->stall)) { |
| pch_udc_complete_transfer(ep); |
| pch_udc_clear_dma(dev, DMA_DIR_RX); |
| ep_out->td_data->status = (ep_out->td_data->status & |
| ~PCH_UDC_BUFF_STS) | |
| PCH_UDC_BS_HST_RDY; |
| pch_udc_ep_clear_nak(ep_out); |
| pch_udc_set_dma(dev, DMA_DIR_RX); |
| pch_udc_ep_set_rrdy(ep_out); |
| } |
| /* On IN interrupt, provide data if we have any */ |
| if ((epsts & UDC_EPSTS_IN) && !(epsts & UDC_EPSTS_TDC) && |
| !(epsts & UDC_EPSTS_TXEMPTY)) |
| pch_udc_start_next_txrequest(ep); |
| } |
| |
| /** |
| * pch_udc_svc_control_out() - Routine that handle Control |
| * OUT endpoint interrupts |
| * @dev: Reference to the device structure |
| */ |
| static void pch_udc_svc_control_out(struct pch_udc_dev *dev) |
| __releases(&dev->lock) |
| __acquires(&dev->lock) |
| { |
| u32 stat; |
| int setup_supported; |
| struct pch_udc_ep *ep; |
| |
| ep = &dev->ep[UDC_EP0OUT_IDX]; |
| stat = ep->epsts; |
| ep->epsts = 0; |
| |
| /* If setup data */ |
| if (((stat & UDC_EPSTS_OUT_MASK) >> UDC_EPSTS_OUT_SHIFT) == |
| UDC_EPSTS_OUT_SETUP) { |
| dev->stall = 0; |
| dev->ep[UDC_EP0IN_IDX].halted = 0; |
| dev->ep[UDC_EP0OUT_IDX].halted = 0; |
| dev->setup_data = ep->td_stp->request; |
| pch_udc_init_setup_buff(ep->td_stp); |
| pch_udc_clear_dma(dev, DMA_DIR_RX); |
| pch_udc_ep_fifo_flush(&(dev->ep[UDC_EP0IN_IDX]), |
| dev->ep[UDC_EP0IN_IDX].in); |
| if ((dev->setup_data.bRequestType & USB_DIR_IN)) |
| dev->gadget.ep0 = &dev->ep[UDC_EP0IN_IDX].ep; |
| else /* OUT */ |
| dev->gadget.ep0 = &ep->ep; |
| spin_unlock(&dev->lock); |
| /* If Mass storage Reset */ |
| if ((dev->setup_data.bRequestType == 0x21) && |
| (dev->setup_data.bRequest == 0xFF)) |
| dev->prot_stall = 0; |
| /* call gadget with setup data received */ |
| setup_supported = dev->driver->setup(&dev->gadget, |
| &dev->setup_data); |
| spin_lock(&dev->lock); |
| |
| if (dev->setup_data.bRequestType & USB_DIR_IN) { |
| ep->td_data->status = (ep->td_data->status & |
| ~PCH_UDC_BUFF_STS) | |
| PCH_UDC_BS_HST_RDY; |
| pch_udc_ep_set_ddptr(ep, ep->td_data_phys); |
| } |
| /* ep0 in returns data on IN phase */ |
| if (setup_supported >= 0 && setup_supported < |
| UDC_EP0IN_MAX_PKT_SIZE) { |
| pch_udc_ep_clear_nak(&(dev->ep[UDC_EP0IN_IDX])); |
| /* Gadget would have queued a request when |
| * we called the setup */ |
| if (!(dev->setup_data.bRequestType & USB_DIR_IN)) { |
| pch_udc_set_dma(dev, DMA_DIR_RX); |
| pch_udc_ep_clear_nak(ep); |
| } |
| } else if (setup_supported < 0) { |
| /* if unsupported request, then stall */ |
| pch_udc_ep_set_stall(&(dev->ep[UDC_EP0IN_IDX])); |
| pch_udc_enable_ep_interrupts(ep->dev, |
| PCH_UDC_EPINT(ep->in, ep->num)); |
| dev->stall = 0; |
| pch_udc_set_dma(dev, DMA_DIR_RX); |
| } else { |
| dev->waiting_zlp_ack = 1; |
| } |
| } else if ((((stat & UDC_EPSTS_OUT_MASK) >> UDC_EPSTS_OUT_SHIFT) == |
| UDC_EPSTS_OUT_DATA) && !dev->stall) { |
| pch_udc_clear_dma(dev, DMA_DIR_RX); |
| pch_udc_ep_set_ddptr(ep, 0); |
| if (!list_empty(&ep->queue)) { |
| ep->epsts = stat; |
| pch_udc_svc_data_out(dev, PCH_UDC_EP0); |
| } |
| pch_udc_set_dma(dev, DMA_DIR_RX); |
| } |
| pch_udc_ep_set_rrdy(ep); |
| } |
| |
| |
| /** |
| * pch_udc_postsvc_epinters() - This function enables end point interrupts |
| * and clears NAK status |
| * @dev: Reference to the device structure |
| * @ep_num: End point number |
| */ |
| static void pch_udc_postsvc_epinters(struct pch_udc_dev *dev, int ep_num) |
| { |
| struct pch_udc_ep *ep; |
| struct pch_udc_request *req; |
| |
| ep = &dev->ep[UDC_EPIN_IDX(ep_num)]; |
| if (!list_empty(&ep->queue)) { |
| req = list_entry(ep->queue.next, struct pch_udc_request, queue); |
| pch_udc_enable_ep_interrupts(ep->dev, |
| PCH_UDC_EPINT(ep->in, ep->num)); |
| pch_udc_ep_clear_nak(ep); |
| } |
| } |
| |
| /** |
| * pch_udc_read_all_epstatus() - This function read all endpoint status |
| * @dev: Reference to the device structure |
| * @ep_intr: Status of endpoint interrupt |
| */ |
| static void pch_udc_read_all_epstatus(struct pch_udc_dev *dev, u32 ep_intr) |
| { |
| int i; |
| struct pch_udc_ep *ep; |
| |
| for (i = 0; i < PCH_UDC_USED_EP_NUM; i++) { |
| /* IN */ |
| if (ep_intr & (0x1 << i)) { |
| ep = &dev->ep[UDC_EPIN_IDX(i)]; |
| ep->epsts = pch_udc_read_ep_status(ep); |
| pch_udc_clear_ep_status(ep, ep->epsts); |
| } |
| /* OUT */ |
| if (ep_intr & (0x10000 << i)) { |
| ep = &dev->ep[UDC_EPOUT_IDX(i)]; |
| ep->epsts = pch_udc_read_ep_status(ep); |
| pch_udc_clear_ep_status(ep, ep->epsts); |
| } |
| } |
| } |
| |
| /** |
| * pch_udc_activate_control_ep() - This function enables the control endpoints |
| * for traffic after a reset |
| * @dev: Reference to the device structure |
| */ |
| static void pch_udc_activate_control_ep(struct pch_udc_dev *dev) |
| { |
| struct pch_udc_ep *ep; |
| u32 val; |
| |
| /* Setup the IN endpoint */ |
| ep = &dev->ep[UDC_EP0IN_IDX]; |
| pch_udc_clear_ep_control(ep); |
| pch_udc_ep_fifo_flush(ep, ep->in); |
| pch_udc_ep_set_bufsz(ep, UDC_EP0IN_BUFF_SIZE, ep->in); |
| pch_udc_ep_set_maxpkt(ep, UDC_EP0IN_MAX_PKT_SIZE); |
| /* Initialize the IN EP Descriptor */ |
| ep->td_data = NULL; |
| ep->td_stp = NULL; |
| ep->td_data_phys = 0; |
| ep->td_stp_phys = 0; |
| |
| /* Setup the OUT endpoint */ |
| ep = &dev->ep[UDC_EP0OUT_IDX]; |
| pch_udc_clear_ep_control(ep); |
| pch_udc_ep_fifo_flush(ep, ep->in); |
| pch_udc_ep_set_bufsz(ep, UDC_EP0OUT_BUFF_SIZE, ep->in); |
| pch_udc_ep_set_maxpkt(ep, UDC_EP0OUT_MAX_PKT_SIZE); |
| val = UDC_EP0OUT_MAX_PKT_SIZE << UDC_CSR_NE_MAX_PKT_SHIFT; |
| pch_udc_write_csr(ep->dev, val, UDC_EP0OUT_IDX); |
| |
| /* Initialize the SETUP buffer */ |
| pch_udc_init_setup_buff(ep->td_stp); |
| /* Write the pointer address of dma descriptor */ |
| pch_udc_ep_set_subptr(ep, ep->td_stp_phys); |
| /* Write the pointer address of Setup descriptor */ |
| pch_udc_ep_set_ddptr(ep, ep->td_data_phys); |
| |
| /* Initialize the dma descriptor */ |
| ep->td_data->status = PCH_UDC_DMA_LAST; |
| ep->td_data->dataptr = dev->dma_addr; |
| ep->td_data->next = ep->td_data_phys; |
| |
| pch_udc_ep_clear_nak(ep); |
| } |
| |
| |
| /** |
| * pch_udc_svc_ur_interrupt() - This function handles a USB reset interrupt |
| * @dev: Reference to driver structure |
| */ |
| static void pch_udc_svc_ur_interrupt(struct pch_udc_dev *dev) |
| { |
| struct pch_udc_ep *ep; |
| int i; |
| |
| pch_udc_clear_dma(dev, DMA_DIR_TX); |
| pch_udc_clear_dma(dev, DMA_DIR_RX); |
| /* Mask all endpoint interrupts */ |
| pch_udc_disable_ep_interrupts(dev, UDC_EPINT_MSK_DISABLE_ALL); |
| /* clear all endpoint interrupts */ |
| pch_udc_write_ep_interrupts(dev, UDC_EPINT_MSK_DISABLE_ALL); |
| |
| for (i = 0; i < PCH_UDC_EP_NUM; i++) { |
| ep = &dev->ep[i]; |
| pch_udc_clear_ep_status(ep, UDC_EPSTS_ALL_CLR_MASK); |
| pch_udc_clear_ep_control(ep); |
| pch_udc_ep_set_ddptr(ep, 0); |
| pch_udc_write_csr(ep->dev, 0x00, i); |
| } |
| dev->stall = 0; |
| dev->prot_stall = 0; |
| dev->waiting_zlp_ack = 0; |
| dev->set_cfg_not_acked = 0; |
| |
| /* disable ep to empty req queue. Skip the control EP's */ |
| for (i = 0; i < (PCH_UDC_USED_EP_NUM*2); i++) { |
| ep = &dev->ep[i]; |
| pch_udc_ep_set_nak(ep); |
| pch_udc_ep_fifo_flush(ep, ep->in); |
| /* Complete request queue */ |
| empty_req_queue(ep); |
| } |
| if (dev->driver) { |
| spin_unlock(&dev->lock); |
| usb_gadget_udc_reset(&dev->gadget, dev->driver); |
| spin_lock(&dev->lock); |
| } |
| } |
| |
| /** |
| * pch_udc_svc_enum_interrupt() - This function handles a USB speed enumeration |
| * done interrupt |
| * @dev: Reference to driver structure |
| */ |
| static void pch_udc_svc_enum_interrupt(struct pch_udc_dev *dev) |
| { |
| u32 dev_stat, dev_speed; |
| u32 speed = USB_SPEED_FULL; |
| |
| dev_stat = pch_udc_read_device_status(dev); |
| dev_speed = (dev_stat & UDC_DEVSTS_ENUM_SPEED_MASK) >> |
| UDC_DEVSTS_ENUM_SPEED_SHIFT; |
| switch (dev_speed) { |
| case UDC_DEVSTS_ENUM_SPEED_HIGH: |
| speed = USB_SPEED_HIGH; |
| break; |
| case UDC_DEVSTS_ENUM_SPEED_FULL: |
| speed = USB_SPEED_FULL; |
| break; |
| case UDC_DEVSTS_ENUM_SPEED_LOW: |
| speed = USB_SPEED_LOW; |
| break; |
| default: |
| BUG(); |
| } |
| dev->gadget.speed = speed; |
| pch_udc_activate_control_ep(dev); |
| pch_udc_enable_ep_interrupts(dev, UDC_EPINT_IN_EP0 | UDC_EPINT_OUT_EP0); |
| pch_udc_set_dma(dev, DMA_DIR_TX); |
| pch_udc_set_dma(dev, DMA_DIR_RX); |
| pch_udc_ep_set_rrdy(&(dev->ep[UDC_EP0OUT_IDX])); |
| |
| /* enable device interrupts */ |
| pch_udc_enable_interrupts(dev, UDC_DEVINT_UR | UDC_DEVINT_US | |
| UDC_DEVINT_ES | UDC_DEVINT_ENUM | |
| UDC_DEVINT_SI | UDC_DEVINT_SC); |
| } |
| |
| /** |
| * pch_udc_svc_intf_interrupt() - This function handles a set interface |
| * interrupt |
| * @dev: Reference to driver structure |
| */ |
| static void pch_udc_svc_intf_interrupt(struct pch_udc_dev *dev) |
| { |
| u32 reg, dev_stat = 0; |
| int i, ret; |
| |
| dev_stat = pch_udc_read_device_status(dev); |
| dev->cfg_data.cur_intf = (dev_stat & UDC_DEVSTS_INTF_MASK) >> |
| UDC_DEVSTS_INTF_SHIFT; |
| dev->cfg_data.cur_alt = (dev_stat & UDC_DEVSTS_ALT_MASK) >> |
| UDC_DEVSTS_ALT_SHIFT; |
| dev->set_cfg_not_acked = 1; |
| /* Construct the usb request for gadget driver and inform it */ |
| memset(&dev->setup_data, 0 , sizeof dev->setup_data); |
| dev->setup_data.bRequest = USB_REQ_SET_INTERFACE; |
| dev->setup_data.bRequestType = USB_RECIP_INTERFACE; |
| dev->setup_data.wValue = cpu_to_le16(dev->cfg_data.cur_alt); |
| dev->setup_data.wIndex = cpu_to_le16(dev->cfg_data.cur_intf); |
| /* programm the Endpoint Cfg registers */ |
| /* Only one end point cfg register */ |
| reg = pch_udc_read_csr(dev, UDC_EP0OUT_IDX); |
| reg = (reg & ~UDC_CSR_NE_INTF_MASK) | |
| (dev->cfg_data.cur_intf << UDC_CSR_NE_INTF_SHIFT); |
| reg = (reg & ~UDC_CSR_NE_ALT_MASK) | |
| (dev->cfg_data.cur_alt << UDC_CSR_NE_ALT_SHIFT); |
| pch_udc_write_csr(dev, reg, UDC_EP0OUT_IDX); |
| for (i = 0; i < PCH_UDC_USED_EP_NUM * 2; i++) { |
| /* clear stall bits */ |
| pch_udc_ep_clear_stall(&(dev->ep[i])); |
| dev->ep[i].halted = 0; |
| } |
| dev->stall = 0; |
| spin_unlock(&dev->lock); |
| ret = dev->driver->setup(&dev->gadget, &dev->setup_data); |
| spin_lock(&dev->lock); |
| } |
| |
| /** |
| * pch_udc_svc_cfg_interrupt() - This function handles a set configuration |
| * interrupt |
| * @dev: Reference to driver structure |
| */ |
| static void pch_udc_svc_cfg_interrupt(struct pch_udc_dev *dev) |
| { |
| int i, ret; |
| u32 reg, dev_stat = 0; |
| |
| dev_stat = pch_udc_read_device_status(dev); |
| dev->set_cfg_not_acked = 1; |
| dev->cfg_data.cur_cfg = (dev_stat & UDC_DEVSTS_CFG_MASK) >> |
| UDC_DEVSTS_CFG_SHIFT; |
| /* make usb request for gadget driver */ |
| memset(&dev->setup_data, 0 , sizeof dev->setup_data); |
| dev->setup_data.bRequest = USB_REQ_SET_CONFIGURATION; |
| dev->setup_data.wValue = cpu_to_le16(dev->cfg_data.cur_cfg); |
| /* program the NE registers */ |
| /* Only one end point cfg register */ |
| reg = pch_udc_read_csr(dev, UDC_EP0OUT_IDX); |
| reg = (reg & ~UDC_CSR_NE_CFG_MASK) | |
| (dev->cfg_data.cur_cfg << UDC_CSR_NE_CFG_SHIFT); |
| pch_udc_write_csr(dev, reg, UDC_EP0OUT_IDX); |
| for (i = 0; i < PCH_UDC_USED_EP_NUM * 2; i++) { |
| /* clear stall bits */ |
| pch_udc_ep_clear_stall(&(dev->ep[i])); |
| dev->ep[i].halted = 0; |
| } |
| dev->stall = 0; |
| |
| /* call gadget zero with setup data received */ |
| spin_unlock(&dev->lock); |
| ret = dev->driver->setup(&dev->gadget, &dev->setup_data); |
| spin_lock(&dev->lock); |
| } |
| |
| /** |
| * pch_udc_dev_isr() - This function services device interrupts |
| * by invoking appropriate routines. |
| * @dev: Reference to the device structure |
| * @dev_intr: The Device interrupt status. |
| */ |
| static void pch_udc_dev_isr(struct pch_udc_dev *dev, u32 dev_intr) |
| { |
| int vbus; |
| |
| /* USB Reset Interrupt */ |
| if (dev_intr & UDC_DEVINT_UR) { |
| pch_udc_svc_ur_interrupt(dev); |
| dev_dbg(&dev->pdev->dev, "USB_RESET\n"); |
| } |
| /* Enumeration Done Interrupt */ |
| if (dev_intr & UDC_DEVINT_ENUM) { |
| pch_udc_svc_enum_interrupt(dev); |
| dev_dbg(&dev->pdev->dev, "USB_ENUM\n"); |
| } |
| /* Set Interface Interrupt */ |
| if (dev_intr & UDC_DEVINT_SI) |
| pch_udc_svc_intf_interrupt(dev); |
| /* Set Config Interrupt */ |
| if (dev_intr & UDC_DEVINT_SC) |
| pch_udc_svc_cfg_interrupt(dev); |
| /* USB Suspend interrupt */ |
| if (dev_intr & UDC_DEVINT_US) { |
| if (dev->driver |
| && dev->driver->suspend) { |
| spin_unlock(&dev->lock); |
| dev->driver->suspend(&dev->gadget); |
| spin_lock(&dev->lock); |
| } |
| |
| vbus = pch_vbus_gpio_get_value(dev); |
| if ((dev->vbus_session == 0) |
| && (vbus != 1)) { |
| if (dev->driver && dev->driver->disconnect) { |
| spin_unlock(&dev->lock); |
| dev->driver->disconnect(&dev->gadget); |
| spin_lock(&dev->lock); |
| } |
| pch_udc_reconnect(dev); |
| } else if ((dev->vbus_session == 0) |
| && (vbus == 1) |
| && !dev->vbus_gpio.intr) |
| schedule_work(&dev->vbus_gpio.irq_work_fall); |
| |
| dev_dbg(&dev->pdev->dev, "USB_SUSPEND\n"); |
| } |
| /* Clear the SOF interrupt, if enabled */ |
| if (dev_intr & UDC_DEVINT_SOF) |
| dev_dbg(&dev->pdev->dev, "SOF\n"); |
| /* ES interrupt, IDLE > 3ms on the USB */ |
| if (dev_intr & UDC_DEVINT_ES) |
| dev_dbg(&dev->pdev->dev, "ES\n"); |
| /* RWKP interrupt */ |
| if (dev_intr & UDC_DEVINT_RWKP) |
| dev_dbg(&dev->pdev->dev, "RWKP\n"); |
| } |
| |
| /** |
| * pch_udc_isr() - This function handles interrupts from the PCH USB Device |
| * @irq: Interrupt request number |
| * @dev: Reference to the device structure |
| */ |
| static irqreturn_t pch_udc_isr(int irq, void *pdev) |
| { |
| struct pch_udc_dev *dev = (struct pch_udc_dev *) pdev; |
| u32 dev_intr, ep_intr; |
| int i; |
| |
| dev_intr = pch_udc_read_device_interrupts(dev); |
| ep_intr = pch_udc_read_ep_interrupts(dev); |
| |
| /* For a hot plug, this find that the controller is hung up. */ |
| if (dev_intr == ep_intr) |
| if (dev_intr == pch_udc_readl(dev, UDC_DEVCFG_ADDR)) { |
| dev_dbg(&dev->pdev->dev, "UDC: Hung up\n"); |
| /* The controller is reset */ |
| pch_udc_writel(dev, UDC_SRST, UDC_SRST_ADDR); |
| return IRQ_HANDLED; |
| } |
| if (dev_intr) |
| /* Clear device interrupts */ |
| pch_udc_write_device_interrupts(dev, dev_intr); |
| if (ep_intr) |
| /* Clear ep interrupts */ |
| pch_udc_write_ep_interrupts(dev, ep_intr); |
| if (!dev_intr && !ep_intr) |
| return IRQ_NONE; |
| spin_lock(&dev->lock); |
| if (dev_intr) |
| pch_udc_dev_isr(dev, dev_intr); |
| if (ep_intr) { |
| pch_udc_read_all_epstatus(dev, ep_intr); |
| /* Process Control In interrupts, if present */ |
| if (ep_intr & UDC_EPINT_IN_EP0) { |
| pch_udc_svc_control_in(dev); |
| pch_udc_postsvc_epinters(dev, 0); |
| } |
| /* Process Control Out interrupts, if present */ |
| if (ep_intr & UDC_EPINT_OUT_EP0) |
| pch_udc_svc_control_out(dev); |
| /* Process data in end point interrupts */ |
| for (i = 1; i < PCH_UDC_USED_EP_NUM; i++) { |
| if (ep_intr & (1 << i)) { |
| pch_udc_svc_data_in(dev, i); |
| pch_udc_postsvc_epinters(dev, i); |
| } |
| } |
| /* Process data out end point interrupts */ |
| for (i = UDC_EPINT_OUT_SHIFT + 1; i < (UDC_EPINT_OUT_SHIFT + |
| PCH_UDC_USED_EP_NUM); i++) |
| if (ep_intr & (1 << i)) |
| pch_udc_svc_data_out(dev, i - |
| UDC_EPINT_OUT_SHIFT); |
| } |
| spin_unlock(&dev->lock); |
| return IRQ_HANDLED; |
| } |
| |
| /** |
| * pch_udc_setup_ep0() - This function enables control endpoint for traffic |
| * @dev: Reference to the device structure |
| */ |
| static void pch_udc_setup_ep0(struct pch_udc_dev *dev) |
| { |
| /* enable ep0 interrupts */ |
| pch_udc_enable_ep_interrupts(dev, UDC_EPINT_IN_EP0 | |
| UDC_EPINT_OUT_EP0); |
| /* enable device interrupts */ |
| pch_udc_enable_interrupts(dev, UDC_DEVINT_UR | UDC_DEVINT_US | |
| UDC_DEVINT_ES | UDC_DEVINT_ENUM | |
| UDC_DEVINT_SI | UDC_DEVINT_SC); |
| } |
| |
| /** |
| * gadget_release() - Free the gadget driver private data |
| * @pdev reference to struct pci_dev |
| */ |
| static void gadget_release(struct device *pdev) |
| { |
| struct pch_udc_dev *dev = dev_get_drvdata(pdev); |
| |
| kfree(dev); |
| } |
| |
| /** |
| * pch_udc_pcd_reinit() - This API initializes the endpoint structures |
| * @dev: Reference to the driver structure |
| */ |
| static void pch_udc_pcd_reinit(struct pch_udc_dev *dev) |
| { |
| const char *const ep_string[] = { |
| ep0_string, "ep0out", "ep1in", "ep1out", "ep2in", "ep2out", |
| "ep3in", "ep3out", "ep4in", "ep4out", "ep5in", "ep5out", |
| "ep6in", "ep6out", "ep7in", "ep7out", "ep8in", "ep8out", |
| "ep9in", "ep9out", "ep10in", "ep10out", "ep11in", "ep11out", |
| "ep12in", "ep12out", "ep13in", "ep13out", "ep14in", "ep14out", |
| "ep15in", "ep15out", |
| }; |
| int i; |
| |
| dev->gadget.speed = USB_SPEED_UNKNOWN; |
| INIT_LIST_HEAD(&dev->gadget.ep_list); |
| |
| /* Initialize the endpoints structures */ |
| memset(dev->ep, 0, sizeof dev->ep); |
| for (i = 0; i < PCH_UDC_EP_NUM; i++) { |
| struct pch_udc_ep *ep = &dev->ep[i]; |
| ep->dev = dev; |
| ep->halted = 1; |
| ep->num = i / 2; |
| ep->in = ~i & 1; |
| ep->ep.name = ep_string[i]; |
| ep->ep.ops = &pch_udc_ep_ops; |
| if (ep->in) |
| ep->offset_addr = ep->num * UDC_EP_REG_SHIFT; |
| else |
| ep->offset_addr = (UDC_EPINT_OUT_SHIFT + ep->num) * |
| UDC_EP_REG_SHIFT; |
| /* need to set ep->ep.maxpacket and set Default Configuration?*/ |
| usb_ep_set_maxpacket_limit(&ep->ep, UDC_BULK_MAX_PKT_SIZE); |
| list_add_tail(&ep->ep.ep_list, &dev->gadget.ep_list); |
| INIT_LIST_HEAD(&ep->queue); |
| } |
| usb_ep_set_maxpacket_limit(&dev->ep[UDC_EP0IN_IDX].ep, UDC_EP0IN_MAX_PKT_SIZE); |
| usb_ep_set_maxpacket_limit(&dev->ep[UDC_EP0OUT_IDX].ep, UDC_EP0OUT_MAX_PKT_SIZE); |
| |
| /* remove ep0 in and out from the list. They have own pointer */ |
| list_del_init(&dev->ep[UDC_EP0IN_IDX].ep.ep_list); |
| list_del_init(&dev->ep[UDC_EP0OUT_IDX].ep.ep_list); |
| |
| dev->gadget.ep0 = &dev->ep[UDC_EP0IN_IDX].ep; |
| INIT_LIST_HEAD(&dev->gadget.ep0->ep_list); |
| } |
| |
| /** |
| * pch_udc_pcd_init() - This API initializes the driver structure |
| * @dev: Reference to the driver structure |
| * |
| * Return codes: |
| * 0: Success |
| */ |
| static int pch_udc_pcd_init(struct pch_udc_dev *dev) |
| { |
| pch_udc_init(dev); |
| pch_udc_pcd_reinit(dev); |
| pch_vbus_gpio_init(dev, vbus_gpio_port); |
| return 0; |
| } |
| |
| /** |
| * init_dma_pools() - create dma pools during initialization |
| * @pdev: reference to struct pci_dev |
| */ |
| static int init_dma_pools(struct pch_udc_dev *dev) |
| { |
| struct pch_udc_stp_dma_desc *td_stp; |
| struct pch_udc_data_dma_desc *td_data; |
| |
| /* DMA setup */ |
| dev->data_requests = pci_pool_create("data_requests", dev->pdev, |
| sizeof(struct pch_udc_data_dma_desc), 0, 0); |
| if (!dev->data_requests) { |
| dev_err(&dev->pdev->dev, "%s: can't get request data pool\n", |
| __func__); |
| return -ENOMEM; |
| } |
| |
| /* dma desc for setup data */ |
| dev->stp_requests = pci_pool_create("setup requests", dev->pdev, |
| sizeof(struct pch_udc_stp_dma_desc), 0, 0); |
| if (!dev->stp_requests) { |
| dev_err(&dev->pdev->dev, "%s: can't get setup request pool\n", |
| __func__); |
| return -ENOMEM; |
| } |
| /* setup */ |
| td_stp = pci_pool_alloc(dev->stp_requests, GFP_KERNEL, |
| &dev->ep[UDC_EP0OUT_IDX].td_stp_phys); |
| if (!td_stp) { |
| dev_err(&dev->pdev->dev, |
| "%s: can't allocate setup dma descriptor\n", __func__); |
| return -ENOMEM; |
| } |
| dev->ep[UDC_EP0OUT_IDX].td_stp = td_stp; |
| |
| /* data: 0 packets !? */ |
| td_data = pci_pool_alloc(dev->data_requests, GFP_KERNEL, |
| &dev->ep[UDC_EP0OUT_IDX].td_data_phys); |
| if (!td_data) { |
| dev_err(&dev->pdev->dev, |
| "%s: can't allocate data dma descriptor\n", __func__); |
| return -ENOMEM; |
| } |
| dev->ep[UDC_EP0OUT_IDX].td_data = td_data; |
| dev->ep[UDC_EP0IN_IDX].td_stp = NULL; |
| dev->ep[UDC_EP0IN_IDX].td_stp_phys = 0; |
| dev->ep[UDC_EP0IN_IDX].td_data = NULL; |
| dev->ep[UDC_EP0IN_IDX].td_data_phys = 0; |
| |
| dev->ep0out_buf = kzalloc(UDC_EP0OUT_BUFF_SIZE * 4, GFP_KERNEL); |
| if (!dev->ep0out_buf) |
| return -ENOMEM; |
| dev->dma_addr = dma_map_single(&dev->pdev->dev, dev->ep0out_buf, |
| UDC_EP0OUT_BUFF_SIZE * 4, |
| DMA_FROM_DEVICE); |
| return 0; |
| } |
| |
| static int pch_udc_start(struct usb_gadget *g, |
| struct usb_gadget_driver *driver) |
| { |
| struct pch_udc_dev *dev = to_pch_udc(g); |
| |
| driver->driver.bus = NULL; |
| dev->driver = driver; |
| |
| /* get ready for ep0 traffic */ |
| pch_udc_setup_ep0(dev); |
| |
| /* clear SD */ |
| if ((pch_vbus_gpio_get_value(dev) != 0) || !dev->vbus_gpio.intr) |
| pch_udc_clear_disconnect(dev); |
| |
| dev->connected = 1; |
| return 0; |
| } |
| |
| static int pch_udc_stop(struct usb_gadget *g) |
| { |
| struct pch_udc_dev *dev = to_pch_udc(g); |
| |
| pch_udc_disable_interrupts(dev, UDC_DEVINT_MSK); |
| |
| /* Assures that there are no pending requests with this driver */ |
| dev->driver = NULL; |
| dev->connected = 0; |
| |
| /* set SD */ |
| pch_udc_set_disconnect(dev); |
| |
| return 0; |
| } |
| |
| static void pch_udc_shutdown(struct pci_dev *pdev) |
| { |
| struct pch_udc_dev *dev = pci_get_drvdata(pdev); |
| |
| pch_udc_disable_interrupts(dev, UDC_DEVINT_MSK); |
| pch_udc_disable_ep_interrupts(dev, UDC_EPINT_MSK_DISABLE_ALL); |
| |
| /* disable the pullup so the host will think we're gone */ |
| pch_udc_set_disconnect(dev); |
| } |
| |
| static void pch_udc_remove(struct pci_dev *pdev) |
| { |
| struct pch_udc_dev *dev = pci_get_drvdata(pdev); |
| |
| usb_del_gadget_udc(&dev->gadget); |
| |
| /* gadget driver must not be registered */ |
| if (dev->driver) |
| dev_err(&pdev->dev, |
| "%s: gadget driver still bound!!!\n", __func__); |
| /* dma pool cleanup */ |
| if (dev->data_requests) |
| pci_pool_destroy(dev->data_requests); |
| |
| if (dev->stp_requests) { |
| /* cleanup DMA desc's for ep0in */ |
| if (dev->ep[UDC_EP0OUT_IDX].td_stp) { |
| pci_pool_free(dev->stp_requests, |
| dev->ep[UDC_EP0OUT_IDX].td_stp, |
| dev->ep[UDC_EP0OUT_IDX].td_stp_phys); |
| } |
| if (dev->ep[UDC_EP0OUT_IDX].td_data) { |
| pci_pool_free(dev->stp_requests, |
| dev->ep[UDC_EP0OUT_IDX].td_data, |
| dev->ep[UDC_EP0OUT_IDX].td_data_phys); |
| } |
| pci_pool_destroy(dev->stp_requests); |
| } |
| |
| if (dev->dma_addr) |
| dma_unmap_single(&dev->pdev->dev, dev->dma_addr, |
| UDC_EP0OUT_BUFF_SIZE * 4, DMA_FROM_DEVICE); |
| kfree(dev->ep0out_buf); |
| |
| pch_vbus_gpio_free(dev); |
| |
| pch_udc_exit(dev); |
| |
| if (dev->irq_registered) |
| free_irq(pdev->irq, dev); |
| if (dev->base_addr) |
| iounmap(dev->base_addr); |
| if (dev->mem_region) |
| release_mem_region(dev->phys_addr, |
| pci_resource_len(pdev, dev->bar)); |
| if (dev->active) |
| pci_disable_device(pdev); |
| kfree(dev); |
| } |
| |
| #ifdef CONFIG_PM |
| static int pch_udc_suspend(struct pci_dev *pdev, pm_message_t state) |
| { |
| struct pch_udc_dev *dev = pci_get_drvdata(pdev); |
| |
| pch_udc_disable_interrupts(dev, UDC_DEVINT_MSK); |
| pch_udc_disable_ep_interrupts(dev, UDC_EPINT_MSK_DISABLE_ALL); |
| |
| pci_disable_device(pdev); |
| pci_enable_wake(pdev, PCI_D3hot, 0); |
| |
| if (pci_save_state(pdev)) { |
| dev_err(&pdev->dev, |
| "%s: could not save PCI config state\n", __func__); |
| return -ENOMEM; |
| } |
| pci_set_power_state(pdev, pci_choose_state(pdev, state)); |
| return 0; |
| } |
| |
| static int pch_udc_resume(struct pci_dev *pdev) |
| { |
| int ret; |
| |
| pci_set_power_state(pdev, PCI_D0); |
| pci_restore_state(pdev); |
| ret = pci_enable_device(pdev); |
| if (ret) { |
| dev_err(&pdev->dev, "%s: pci_enable_device failed\n", __func__); |
| return ret; |
| } |
| pci_enable_wake(pdev, PCI_D3hot, 0); |
| return 0; |
| } |
| #else |
| #define pch_udc_suspend NULL |
| #define pch_udc_resume NULL |
| #endif /* CONFIG_PM */ |
| |
| static int pch_udc_probe(struct pci_dev *pdev, |
| const struct pci_device_id *id) |
| { |
| unsigned long resource; |
| unsigned long len; |
| int retval; |
| struct pch_udc_dev *dev; |
| |
| /* init */ |
| dev = kzalloc(sizeof *dev, GFP_KERNEL); |
| if (!dev) { |
| pr_err("%s: no memory for device structure\n", __func__); |
| return -ENOMEM; |
| } |
| /* pci setup */ |
| if (pci_enable_device(pdev) < 0) { |
| kfree(dev); |
| pr_err("%s: pci_enable_device failed\n", __func__); |
| return -ENODEV; |
| } |
| dev->active = 1; |
| pci_set_drvdata(pdev, dev); |
| |
| /* Determine BAR based on PCI ID */ |
| if (id->device == PCI_DEVICE_ID_INTEL_QUARK_X1000_UDC) |
| dev->bar = PCH_UDC_PCI_BAR_QUARK_X1000; |
| else |
| dev->bar = PCH_UDC_PCI_BAR; |
| |
| /* PCI resource allocation */ |
| resource = pci_resource_start(pdev, dev->bar); |
| len = pci_resource_len(pdev, dev->bar); |
| |
| if (!request_mem_region(resource, len, KBUILD_MODNAME)) { |
| dev_err(&pdev->dev, "%s: pci device used already\n", __func__); |
| retval = -EBUSY; |
| goto finished; |
| } |
| dev->phys_addr = resource; |
| dev->mem_region = 1; |
| |
| dev->base_addr = ioremap_nocache(resource, len); |
| if (!dev->base_addr) { |
| pr_err("%s: device memory cannot be mapped\n", __func__); |
| retval = -ENOMEM; |
| goto finished; |
| } |
| if (!pdev->irq) { |
| dev_err(&pdev->dev, "%s: irq not set\n", __func__); |
| retval = -ENODEV; |
| goto finished; |
| } |
| /* initialize the hardware */ |
| if (pch_udc_pcd_init(dev)) { |
| retval = -ENODEV; |
| goto finished; |
| } |
| if (request_irq(pdev->irq, pch_udc_isr, IRQF_SHARED, KBUILD_MODNAME, |
| dev)) { |
| dev_err(&pdev->dev, "%s: request_irq(%d) fail\n", __func__, |
| pdev->irq); |
| retval = -ENODEV; |
| goto finished; |
| } |
| dev->irq = pdev->irq; |
| dev->irq_registered = 1; |
| |
| pci_set_master(pdev); |
| pci_try_set_mwi(pdev); |
| |
| /* device struct setup */ |
| spin_lock_init(&dev->lock); |
| dev->pdev = pdev; |
| dev->gadget.ops = &pch_udc_ops; |
| |
| retval = init_dma_pools(dev); |
| if (retval) |
| goto finished; |
| |
| dev->gadget.name = KBUILD_MODNAME; |
| dev->gadget.max_speed = USB_SPEED_HIGH; |
| |
| /* Put the device in disconnected state till a driver is bound */ |
| pch_udc_set_disconnect(dev); |
| retval = usb_add_gadget_udc_release(&pdev->dev, &dev->gadget, |
| gadget_release); |
| if (retval) |
| goto finished; |
| return 0; |
| |
| finished: |
| pch_udc_remove(pdev); |
| return retval; |
| } |
| |
| static const struct pci_device_id pch_udc_pcidev_id[] = { |
| { |
| PCI_DEVICE(PCI_VENDOR_ID_INTEL, |
| PCI_DEVICE_ID_INTEL_QUARK_X1000_UDC), |
| .class = (PCI_CLASS_SERIAL_USB << 8) | 0xfe, |
| .class_mask = 0xffffffff, |
| }, |
| { |
| PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_EG20T_UDC), |
| .class = (PCI_CLASS_SERIAL_USB << 8) | 0xfe, |
| .class_mask = 0xffffffff, |
| }, |
| { |
| PCI_DEVICE(PCI_VENDOR_ID_ROHM, PCI_DEVICE_ID_ML7213_IOH_UDC), |
| .class = (PCI_CLASS_SERIAL_USB << 8) | 0xfe, |
| .class_mask = 0xffffffff, |
| }, |
| { |
| PCI_DEVICE(PCI_VENDOR_ID_ROHM, PCI_DEVICE_ID_ML7831_IOH_UDC), |
| .class = (PCI_CLASS_SERIAL_USB << 8) | 0xfe, |
| .class_mask = 0xffffffff, |
| }, |
| { 0 }, |
| }; |
| |
| MODULE_DEVICE_TABLE(pci, pch_udc_pcidev_id); |
| |
| static struct pci_driver pch_udc_driver = { |
| .name = KBUILD_MODNAME, |
| .id_table = pch_udc_pcidev_id, |
| .probe = pch_udc_probe, |
| .remove = pch_udc_remove, |
| .suspend = pch_udc_suspend, |
| .resume = pch_udc_resume, |
| .shutdown = pch_udc_shutdown, |
| }; |
| |
| module_pci_driver(pch_udc_driver); |
| |
| MODULE_DESCRIPTION("Intel EG20T USB Device Controller"); |
| MODULE_AUTHOR("LAPIS Semiconductor, <tomoya-linux@dsn.lapis-semi.com>"); |
| MODULE_LICENSE("GPL"); |