| /* |
| * Set up the interrupt priorities |
| * |
| * Copyright 2004-2009 Analog Devices Inc. |
| * 2003 Bas Vermeulen <bas@buyways.nl> |
| * 2002 Arcturus Networks Inc. MaTed <mated@sympatico.ca> |
| * 2000-2001 Lineo, Inc. D. Jefff Dionne <jeff@lineo.ca> |
| * 1999 D. Jeff Dionne <jeff@uclinux.org> |
| * 1996 Roman Zippel |
| * |
| * Licensed under the GPL-2 |
| */ |
| |
| #include <linux/module.h> |
| #include <linux/kernel_stat.h> |
| #include <linux/seq_file.h> |
| #include <linux/irq.h> |
| #ifdef CONFIG_IPIPE |
| #include <linux/ipipe.h> |
| #endif |
| #ifdef CONFIG_KGDB |
| #include <linux/kgdb.h> |
| #endif |
| #include <asm/traps.h> |
| #include <asm/blackfin.h> |
| #include <asm/gpio.h> |
| #include <asm/irq_handler.h> |
| #include <asm/dpmc.h> |
| #include <asm/bfin5xx_spi.h> |
| #include <asm/bfin_sport.h> |
| #include <asm/bfin_can.h> |
| |
| #define SIC_SYSIRQ(irq) (irq - (IRQ_CORETMR + 1)) |
| |
| #ifdef BF537_FAMILY |
| # define BF537_GENERIC_ERROR_INT_DEMUX |
| # define SPI_ERR_MASK (BIT_STAT_TXCOL | BIT_STAT_RBSY | BIT_STAT_MODF | BIT_STAT_TXE) /* SPI_STAT */ |
| # define SPORT_ERR_MASK (ROVF | RUVF | TOVF | TUVF) /* SPORT_STAT */ |
| # define PPI_ERR_MASK (0xFFFF & ~FLD) /* PPI_STATUS */ |
| # define EMAC_ERR_MASK (PHYINT | MMCINT | RXFSINT | TXFSINT | WAKEDET | RXDMAERR | TXDMAERR | STMDONE) /* EMAC_SYSTAT */ |
| # define UART_ERR_MASK (0x6) /* UART_IIR */ |
| # define CAN_ERR_MASK (EWTIF | EWRIF | EPIF | BOIF | WUIF | UIAIF | AAIF | RMLIF | UCEIF | EXTIF | ADIF) /* CAN_GIF */ |
| #else |
| # undef BF537_GENERIC_ERROR_INT_DEMUX |
| #endif |
| |
| /* |
| * NOTES: |
| * - we have separated the physical Hardware interrupt from the |
| * levels that the LINUX kernel sees (see the description in irq.h) |
| * - |
| */ |
| |
| #ifndef CONFIG_SMP |
| /* Initialize this to an actual value to force it into the .data |
| * section so that we know it is properly initialized at entry into |
| * the kernel but before bss is initialized to zero (which is where |
| * it would live otherwise). The 0x1f magic represents the IRQs we |
| * cannot actually mask out in hardware. |
| */ |
| unsigned long bfin_irq_flags = 0x1f; |
| EXPORT_SYMBOL(bfin_irq_flags); |
| #endif |
| |
| /* The number of spurious interrupts */ |
| atomic_t num_spurious; |
| |
| #ifdef CONFIG_PM |
| unsigned long bfin_sic_iwr[3]; /* Up to 3 SIC_IWRx registers */ |
| unsigned vr_wakeup; |
| #endif |
| |
| struct ivgx { |
| /* irq number for request_irq, available in mach-bf5xx/irq.h */ |
| unsigned int irqno; |
| /* corresponding bit in the SIC_ISR register */ |
| unsigned int isrflag; |
| } ivg_table[NR_PERI_INTS]; |
| |
| struct ivg_slice { |
| /* position of first irq in ivg_table for given ivg */ |
| struct ivgx *ifirst; |
| struct ivgx *istop; |
| } ivg7_13[IVG13 - IVG7 + 1]; |
| |
| |
| /* |
| * Search SIC_IAR and fill tables with the irqvalues |
| * and their positions in the SIC_ISR register. |
| */ |
| static void __init search_IAR(void) |
| { |
| unsigned ivg, irq_pos = 0; |
| for (ivg = 0; ivg <= IVG13 - IVG7; ivg++) { |
| int irqn; |
| |
| ivg7_13[ivg].istop = ivg7_13[ivg].ifirst = &ivg_table[irq_pos]; |
| |
| for (irqn = 0; irqn < NR_PERI_INTS; irqn++) { |
| int iar_shift = (irqn & 7) * 4; |
| if (ivg == (0xf & |
| #if defined(CONFIG_BF52x) || defined(CONFIG_BF538) \ |
| || defined(CONFIG_BF539) || defined(CONFIG_BF51x) |
| bfin_read32((unsigned long *)SIC_IAR0 + |
| ((irqn % 32) >> 3) + ((irqn / 32) * |
| ((SIC_IAR4 - SIC_IAR0) / 4))) >> iar_shift)) { |
| #else |
| bfin_read32((unsigned long *)SIC_IAR0 + |
| (irqn >> 3)) >> iar_shift)) { |
| #endif |
| ivg_table[irq_pos].irqno = IVG7 + irqn; |
| ivg_table[irq_pos].isrflag = 1 << (irqn % 32); |
| ivg7_13[ivg].istop++; |
| irq_pos++; |
| } |
| } |
| } |
| } |
| |
| /* |
| * This is for core internal IRQs |
| */ |
| |
| static void bfin_ack_noop(unsigned int irq) |
| { |
| /* Dummy function. */ |
| } |
| |
| static void bfin_core_mask_irq(unsigned int irq) |
| { |
| bfin_irq_flags &= ~(1 << irq); |
| if (!irqs_disabled_hw()) |
| local_irq_enable_hw(); |
| } |
| |
| static void bfin_core_unmask_irq(unsigned int irq) |
| { |
| bfin_irq_flags |= 1 << irq; |
| /* |
| * If interrupts are enabled, IMASK must contain the same value |
| * as bfin_irq_flags. Make sure that invariant holds. If interrupts |
| * are currently disabled we need not do anything; one of the |
| * callers will take care of setting IMASK to the proper value |
| * when reenabling interrupts. |
| * local_irq_enable just does "STI bfin_irq_flags", so it's exactly |
| * what we need. |
| */ |
| if (!irqs_disabled_hw()) |
| local_irq_enable_hw(); |
| return; |
| } |
| |
| static void bfin_internal_mask_irq(unsigned int irq) |
| { |
| unsigned long flags; |
| |
| #ifdef CONFIG_BF53x |
| local_irq_save_hw(flags); |
| bfin_write_SIC_IMASK(bfin_read_SIC_IMASK() & |
| ~(1 << SIC_SYSIRQ(irq))); |
| #else |
| unsigned mask_bank, mask_bit; |
| local_irq_save_hw(flags); |
| mask_bank = SIC_SYSIRQ(irq) / 32; |
| mask_bit = SIC_SYSIRQ(irq) % 32; |
| bfin_write_SIC_IMASK(mask_bank, bfin_read_SIC_IMASK(mask_bank) & |
| ~(1 << mask_bit)); |
| #ifdef CONFIG_SMP |
| bfin_write_SICB_IMASK(mask_bank, bfin_read_SICB_IMASK(mask_bank) & |
| ~(1 << mask_bit)); |
| #endif |
| #endif |
| local_irq_restore_hw(flags); |
| } |
| |
| #ifdef CONFIG_SMP |
| static void bfin_internal_unmask_irq_affinity(unsigned int irq, |
| const struct cpumask *affinity) |
| #else |
| static void bfin_internal_unmask_irq(unsigned int irq) |
| #endif |
| { |
| unsigned long flags; |
| |
| #ifdef CONFIG_BF53x |
| local_irq_save_hw(flags); |
| bfin_write_SIC_IMASK(bfin_read_SIC_IMASK() | |
| (1 << SIC_SYSIRQ(irq))); |
| #else |
| unsigned mask_bank, mask_bit; |
| local_irq_save_hw(flags); |
| mask_bank = SIC_SYSIRQ(irq) / 32; |
| mask_bit = SIC_SYSIRQ(irq) % 32; |
| #ifdef CONFIG_SMP |
| if (cpumask_test_cpu(0, affinity)) |
| #endif |
| bfin_write_SIC_IMASK(mask_bank, |
| bfin_read_SIC_IMASK(mask_bank) | |
| (1 << mask_bit)); |
| #ifdef CONFIG_SMP |
| if (cpumask_test_cpu(1, affinity)) |
| bfin_write_SICB_IMASK(mask_bank, |
| bfin_read_SICB_IMASK(mask_bank) | |
| (1 << mask_bit)); |
| #endif |
| #endif |
| local_irq_restore_hw(flags); |
| } |
| |
| #ifdef CONFIG_SMP |
| static void bfin_internal_unmask_irq(unsigned int irq) |
| { |
| struct irq_desc *desc = irq_to_desc(irq); |
| bfin_internal_unmask_irq_affinity(irq, desc->affinity); |
| } |
| |
| static int bfin_internal_set_affinity(unsigned int irq, const struct cpumask *mask) |
| { |
| bfin_internal_mask_irq(irq); |
| bfin_internal_unmask_irq_affinity(irq, mask); |
| |
| return 0; |
| } |
| #endif |
| |
| #ifdef CONFIG_PM |
| int bfin_internal_set_wake(unsigned int irq, unsigned int state) |
| { |
| u32 bank, bit, wakeup = 0; |
| unsigned long flags; |
| bank = SIC_SYSIRQ(irq) / 32; |
| bit = SIC_SYSIRQ(irq) % 32; |
| |
| switch (irq) { |
| #ifdef IRQ_RTC |
| case IRQ_RTC: |
| wakeup |= WAKE; |
| break; |
| #endif |
| #ifdef IRQ_CAN0_RX |
| case IRQ_CAN0_RX: |
| wakeup |= CANWE; |
| break; |
| #endif |
| #ifdef IRQ_CAN1_RX |
| case IRQ_CAN1_RX: |
| wakeup |= CANWE; |
| break; |
| #endif |
| #ifdef IRQ_USB_INT0 |
| case IRQ_USB_INT0: |
| wakeup |= USBWE; |
| break; |
| #endif |
| #ifdef CONFIG_BF54x |
| case IRQ_CNT: |
| wakeup |= ROTWE; |
| break; |
| #endif |
| default: |
| break; |
| } |
| |
| local_irq_save_hw(flags); |
| |
| if (state) { |
| bfin_sic_iwr[bank] |= (1 << bit); |
| vr_wakeup |= wakeup; |
| |
| } else { |
| bfin_sic_iwr[bank] &= ~(1 << bit); |
| vr_wakeup &= ~wakeup; |
| } |
| |
| local_irq_restore_hw(flags); |
| |
| return 0; |
| } |
| #endif |
| |
| static struct irq_chip bfin_core_irqchip = { |
| .name = "CORE", |
| .ack = bfin_ack_noop, |
| .mask = bfin_core_mask_irq, |
| .unmask = bfin_core_unmask_irq, |
| }; |
| |
| static struct irq_chip bfin_internal_irqchip = { |
| .name = "INTN", |
| .ack = bfin_ack_noop, |
| .mask = bfin_internal_mask_irq, |
| .unmask = bfin_internal_unmask_irq, |
| .mask_ack = bfin_internal_mask_irq, |
| .disable = bfin_internal_mask_irq, |
| .enable = bfin_internal_unmask_irq, |
| #ifdef CONFIG_SMP |
| .set_affinity = bfin_internal_set_affinity, |
| #endif |
| #ifdef CONFIG_PM |
| .set_wake = bfin_internal_set_wake, |
| #endif |
| }; |
| |
| static void bfin_handle_irq(unsigned irq) |
| { |
| #ifdef CONFIG_IPIPE |
| struct pt_regs regs; /* Contents not used. */ |
| ipipe_trace_irq_entry(irq); |
| __ipipe_handle_irq(irq, ®s); |
| ipipe_trace_irq_exit(irq); |
| #else /* !CONFIG_IPIPE */ |
| struct irq_desc *desc = irq_desc + irq; |
| desc->handle_irq(irq, desc); |
| #endif /* !CONFIG_IPIPE */ |
| } |
| |
| #ifdef BF537_GENERIC_ERROR_INT_DEMUX |
| static int error_int_mask; |
| |
| static void bfin_generic_error_mask_irq(unsigned int irq) |
| { |
| error_int_mask &= ~(1L << (irq - IRQ_PPI_ERROR)); |
| if (!error_int_mask) |
| bfin_internal_mask_irq(IRQ_GENERIC_ERROR); |
| } |
| |
| static void bfin_generic_error_unmask_irq(unsigned int irq) |
| { |
| bfin_internal_unmask_irq(IRQ_GENERIC_ERROR); |
| error_int_mask |= 1L << (irq - IRQ_PPI_ERROR); |
| } |
| |
| static struct irq_chip bfin_generic_error_irqchip = { |
| .name = "ERROR", |
| .ack = bfin_ack_noop, |
| .mask_ack = bfin_generic_error_mask_irq, |
| .mask = bfin_generic_error_mask_irq, |
| .unmask = bfin_generic_error_unmask_irq, |
| }; |
| |
| static void bfin_demux_error_irq(unsigned int int_err_irq, |
| struct irq_desc *inta_desc) |
| { |
| int irq = 0; |
| |
| #if (defined(CONFIG_BF537) || defined(CONFIG_BF536)) |
| if (bfin_read_EMAC_SYSTAT() & EMAC_ERR_MASK) |
| irq = IRQ_MAC_ERROR; |
| else |
| #endif |
| if (bfin_read_SPORT0_STAT() & SPORT_ERR_MASK) |
| irq = IRQ_SPORT0_ERROR; |
| else if (bfin_read_SPORT1_STAT() & SPORT_ERR_MASK) |
| irq = IRQ_SPORT1_ERROR; |
| else if (bfin_read_PPI_STATUS() & PPI_ERR_MASK) |
| irq = IRQ_PPI_ERROR; |
| else if (bfin_read_CAN_GIF() & CAN_ERR_MASK) |
| irq = IRQ_CAN_ERROR; |
| else if (bfin_read_SPI_STAT() & SPI_ERR_MASK) |
| irq = IRQ_SPI_ERROR; |
| else if ((bfin_read_UART0_IIR() & UART_ERR_MASK) == UART_ERR_MASK) |
| irq = IRQ_UART0_ERROR; |
| else if ((bfin_read_UART1_IIR() & UART_ERR_MASK) == UART_ERR_MASK) |
| irq = IRQ_UART1_ERROR; |
| |
| if (irq) { |
| if (error_int_mask & (1L << (irq - IRQ_PPI_ERROR))) |
| bfin_handle_irq(irq); |
| else { |
| |
| switch (irq) { |
| case IRQ_PPI_ERROR: |
| bfin_write_PPI_STATUS(PPI_ERR_MASK); |
| break; |
| #if (defined(CONFIG_BF537) || defined(CONFIG_BF536)) |
| case IRQ_MAC_ERROR: |
| bfin_write_EMAC_SYSTAT(EMAC_ERR_MASK); |
| break; |
| #endif |
| case IRQ_SPORT0_ERROR: |
| bfin_write_SPORT0_STAT(SPORT_ERR_MASK); |
| break; |
| |
| case IRQ_SPORT1_ERROR: |
| bfin_write_SPORT1_STAT(SPORT_ERR_MASK); |
| break; |
| |
| case IRQ_CAN_ERROR: |
| bfin_write_CAN_GIS(CAN_ERR_MASK); |
| break; |
| |
| case IRQ_SPI_ERROR: |
| bfin_write_SPI_STAT(SPI_ERR_MASK); |
| break; |
| |
| default: |
| break; |
| } |
| |
| pr_debug("IRQ %d:" |
| " MASKED PERIPHERAL ERROR INTERRUPT ASSERTED\n", |
| irq); |
| } |
| } else |
| printk(KERN_ERR |
| "%s : %s : LINE %d :\nIRQ ?: PERIPHERAL ERROR" |
| " INTERRUPT ASSERTED BUT NO SOURCE FOUND\n", |
| __func__, __FILE__, __LINE__); |
| |
| } |
| #endif /* BF537_GENERIC_ERROR_INT_DEMUX */ |
| |
| #if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE) |
| static int mac_stat_int_mask; |
| |
| static void bfin_mac_status_ack_irq(unsigned int irq) |
| { |
| switch (irq) { |
| case IRQ_MAC_MMCINT: |
| bfin_write_EMAC_MMC_TIRQS( |
| bfin_read_EMAC_MMC_TIRQE() & |
| bfin_read_EMAC_MMC_TIRQS()); |
| bfin_write_EMAC_MMC_RIRQS( |
| bfin_read_EMAC_MMC_RIRQE() & |
| bfin_read_EMAC_MMC_RIRQS()); |
| break; |
| case IRQ_MAC_RXFSINT: |
| bfin_write_EMAC_RX_STKY( |
| bfin_read_EMAC_RX_IRQE() & |
| bfin_read_EMAC_RX_STKY()); |
| break; |
| case IRQ_MAC_TXFSINT: |
| bfin_write_EMAC_TX_STKY( |
| bfin_read_EMAC_TX_IRQE() & |
| bfin_read_EMAC_TX_STKY()); |
| break; |
| case IRQ_MAC_WAKEDET: |
| bfin_write_EMAC_WKUP_CTL( |
| bfin_read_EMAC_WKUP_CTL() | MPKS | RWKS); |
| break; |
| default: |
| /* These bits are W1C */ |
| bfin_write_EMAC_SYSTAT(1L << (irq - IRQ_MAC_PHYINT)); |
| break; |
| } |
| } |
| |
| static void bfin_mac_status_mask_irq(unsigned int irq) |
| { |
| mac_stat_int_mask &= ~(1L << (irq - IRQ_MAC_PHYINT)); |
| #ifdef BF537_GENERIC_ERROR_INT_DEMUX |
| switch (irq) { |
| case IRQ_MAC_PHYINT: |
| bfin_write_EMAC_SYSCTL(bfin_read_EMAC_SYSCTL() & ~PHYIE); |
| break; |
| default: |
| break; |
| } |
| #else |
| if (!mac_stat_int_mask) |
| bfin_internal_mask_irq(IRQ_MAC_ERROR); |
| #endif |
| bfin_mac_status_ack_irq(irq); |
| } |
| |
| static void bfin_mac_status_unmask_irq(unsigned int irq) |
| { |
| #ifdef BF537_GENERIC_ERROR_INT_DEMUX |
| switch (irq) { |
| case IRQ_MAC_PHYINT: |
| bfin_write_EMAC_SYSCTL(bfin_read_EMAC_SYSCTL() | PHYIE); |
| break; |
| default: |
| break; |
| } |
| #else |
| if (!mac_stat_int_mask) |
| bfin_internal_unmask_irq(IRQ_MAC_ERROR); |
| #endif |
| mac_stat_int_mask |= 1L << (irq - IRQ_MAC_PHYINT); |
| } |
| |
| #ifdef CONFIG_PM |
| int bfin_mac_status_set_wake(unsigned int irq, unsigned int state) |
| { |
| #ifdef BF537_GENERIC_ERROR_INT_DEMUX |
| return bfin_internal_set_wake(IRQ_GENERIC_ERROR, state); |
| #else |
| return bfin_internal_set_wake(IRQ_MAC_ERROR, state); |
| #endif |
| } |
| #endif |
| |
| static struct irq_chip bfin_mac_status_irqchip = { |
| .name = "MACST", |
| .ack = bfin_ack_noop, |
| .mask_ack = bfin_mac_status_mask_irq, |
| .mask = bfin_mac_status_mask_irq, |
| .unmask = bfin_mac_status_unmask_irq, |
| #ifdef CONFIG_PM |
| .set_wake = bfin_mac_status_set_wake, |
| #endif |
| }; |
| |
| static void bfin_demux_mac_status_irq(unsigned int int_err_irq, |
| struct irq_desc *inta_desc) |
| { |
| int i, irq = 0; |
| u32 status = bfin_read_EMAC_SYSTAT(); |
| |
| for (i = 0; i < (IRQ_MAC_STMDONE - IRQ_MAC_PHYINT); i++) |
| if (status & (1L << i)) { |
| irq = IRQ_MAC_PHYINT + i; |
| break; |
| } |
| |
| if (irq) { |
| if (mac_stat_int_mask & (1L << (irq - IRQ_MAC_PHYINT))) { |
| bfin_handle_irq(irq); |
| } else { |
| bfin_mac_status_ack_irq(irq); |
| pr_debug("IRQ %d:" |
| " MASKED MAC ERROR INTERRUPT ASSERTED\n", |
| irq); |
| } |
| } else |
| printk(KERN_ERR |
| "%s : %s : LINE %d :\nIRQ ?: MAC ERROR" |
| " INTERRUPT ASSERTED BUT NO SOURCE FOUND\n", |
| __func__, __FILE__, __LINE__); |
| } |
| #endif |
| |
| static inline void bfin_set_irq_handler(unsigned irq, irq_flow_handler_t handle) |
| { |
| #ifdef CONFIG_IPIPE |
| _set_irq_handler(irq, handle_level_irq); |
| #else |
| struct irq_desc *desc = irq_desc + irq; |
| /* May not call generic set_irq_handler() due to spinlock |
| recursion. */ |
| desc->handle_irq = handle; |
| #endif |
| } |
| |
| static DECLARE_BITMAP(gpio_enabled, MAX_BLACKFIN_GPIOS); |
| extern void bfin_gpio_irq_prepare(unsigned gpio); |
| |
| #if !defined(CONFIG_BF54x) |
| |
| static void bfin_gpio_ack_irq(unsigned int irq) |
| { |
| /* AFAIK ack_irq in case mask_ack is provided |
| * get's only called for edge sense irqs |
| */ |
| set_gpio_data(irq_to_gpio(irq), 0); |
| } |
| |
| static void bfin_gpio_mask_ack_irq(unsigned int irq) |
| { |
| struct irq_desc *desc = irq_desc + irq; |
| u32 gpionr = irq_to_gpio(irq); |
| |
| if (desc->handle_irq == handle_edge_irq) |
| set_gpio_data(gpionr, 0); |
| |
| set_gpio_maska(gpionr, 0); |
| } |
| |
| static void bfin_gpio_mask_irq(unsigned int irq) |
| { |
| set_gpio_maska(irq_to_gpio(irq), 0); |
| } |
| |
| static void bfin_gpio_unmask_irq(unsigned int irq) |
| { |
| set_gpio_maska(irq_to_gpio(irq), 1); |
| } |
| |
| static unsigned int bfin_gpio_irq_startup(unsigned int irq) |
| { |
| u32 gpionr = irq_to_gpio(irq); |
| |
| if (__test_and_set_bit(gpionr, gpio_enabled)) |
| bfin_gpio_irq_prepare(gpionr); |
| |
| bfin_gpio_unmask_irq(irq); |
| |
| return 0; |
| } |
| |
| static void bfin_gpio_irq_shutdown(unsigned int irq) |
| { |
| u32 gpionr = irq_to_gpio(irq); |
| |
| bfin_gpio_mask_irq(irq); |
| __clear_bit(gpionr, gpio_enabled); |
| bfin_gpio_irq_free(gpionr); |
| } |
| |
| static int bfin_gpio_irq_type(unsigned int irq, unsigned int type) |
| { |
| int ret; |
| char buf[16]; |
| u32 gpionr = irq_to_gpio(irq); |
| |
| if (type == IRQ_TYPE_PROBE) { |
| /* only probe unenabled GPIO interrupt lines */ |
| if (test_bit(gpionr, gpio_enabled)) |
| return 0; |
| type = IRQ_TYPE_EDGE_RISING | IRQ_TYPE_EDGE_FALLING; |
| } |
| |
| if (type & (IRQ_TYPE_EDGE_RISING | IRQ_TYPE_EDGE_FALLING | |
| IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_LEVEL_LOW)) { |
| |
| snprintf(buf, 16, "gpio-irq%d", irq); |
| ret = bfin_gpio_irq_request(gpionr, buf); |
| if (ret) |
| return ret; |
| |
| if (__test_and_set_bit(gpionr, gpio_enabled)) |
| bfin_gpio_irq_prepare(gpionr); |
| |
| } else { |
| __clear_bit(gpionr, gpio_enabled); |
| return 0; |
| } |
| |
| set_gpio_inen(gpionr, 0); |
| set_gpio_dir(gpionr, 0); |
| |
| if ((type & (IRQ_TYPE_EDGE_RISING | IRQ_TYPE_EDGE_FALLING)) |
| == (IRQ_TYPE_EDGE_RISING | IRQ_TYPE_EDGE_FALLING)) |
| set_gpio_both(gpionr, 1); |
| else |
| set_gpio_both(gpionr, 0); |
| |
| if ((type & (IRQ_TYPE_EDGE_FALLING | IRQ_TYPE_LEVEL_LOW))) |
| set_gpio_polar(gpionr, 1); /* low or falling edge denoted by one */ |
| else |
| set_gpio_polar(gpionr, 0); /* high or rising edge denoted by zero */ |
| |
| if (type & (IRQ_TYPE_EDGE_RISING | IRQ_TYPE_EDGE_FALLING)) { |
| set_gpio_edge(gpionr, 1); |
| set_gpio_inen(gpionr, 1); |
| set_gpio_data(gpionr, 0); |
| |
| } else { |
| set_gpio_edge(gpionr, 0); |
| set_gpio_inen(gpionr, 1); |
| } |
| |
| if (type & (IRQ_TYPE_EDGE_RISING | IRQ_TYPE_EDGE_FALLING)) |
| bfin_set_irq_handler(irq, handle_edge_irq); |
| else |
| bfin_set_irq_handler(irq, handle_level_irq); |
| |
| return 0; |
| } |
| |
| #ifdef CONFIG_PM |
| int bfin_gpio_set_wake(unsigned int irq, unsigned int state) |
| { |
| unsigned gpio = irq_to_gpio(irq); |
| |
| if (state) |
| gpio_pm_wakeup_request(gpio, PM_WAKE_IGNORE); |
| else |
| gpio_pm_wakeup_free(gpio); |
| |
| return 0; |
| } |
| #endif |
| |
| static void bfin_demux_gpio_irq(unsigned int inta_irq, |
| struct irq_desc *desc) |
| { |
| unsigned int i, gpio, mask, irq, search = 0; |
| |
| switch (inta_irq) { |
| #if defined(CONFIG_BF53x) |
| case IRQ_PROG_INTA: |
| irq = IRQ_PF0; |
| search = 1; |
| break; |
| # if defined(BF537_FAMILY) && !(defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)) |
| case IRQ_MAC_RX: |
| irq = IRQ_PH0; |
| break; |
| # endif |
| #elif defined(CONFIG_BF538) || defined(CONFIG_BF539) |
| case IRQ_PORTF_INTA: |
| irq = IRQ_PF0; |
| break; |
| #elif defined(CONFIG_BF52x) || defined(CONFIG_BF51x) |
| case IRQ_PORTF_INTA: |
| irq = IRQ_PF0; |
| break; |
| case IRQ_PORTG_INTA: |
| irq = IRQ_PG0; |
| break; |
| case IRQ_PORTH_INTA: |
| irq = IRQ_PH0; |
| break; |
| #elif defined(CONFIG_BF561) |
| case IRQ_PROG0_INTA: |
| irq = IRQ_PF0; |
| break; |
| case IRQ_PROG1_INTA: |
| irq = IRQ_PF16; |
| break; |
| case IRQ_PROG2_INTA: |
| irq = IRQ_PF32; |
| break; |
| #endif |
| default: |
| BUG(); |
| return; |
| } |
| |
| if (search) { |
| for (i = 0; i < MAX_BLACKFIN_GPIOS; i += GPIO_BANKSIZE) { |
| irq += i; |
| |
| mask = get_gpiop_data(i) & get_gpiop_maska(i); |
| |
| while (mask) { |
| if (mask & 1) |
| bfin_handle_irq(irq); |
| irq++; |
| mask >>= 1; |
| } |
| } |
| } else { |
| gpio = irq_to_gpio(irq); |
| mask = get_gpiop_data(gpio) & get_gpiop_maska(gpio); |
| |
| do { |
| if (mask & 1) |
| bfin_handle_irq(irq); |
| irq++; |
| mask >>= 1; |
| } while (mask); |
| } |
| |
| } |
| |
| #else /* CONFIG_BF54x */ |
| |
| #define NR_PINT_SYS_IRQS 4 |
| #define NR_PINT_BITS 32 |
| #define NR_PINTS 160 |
| #define IRQ_NOT_AVAIL 0xFF |
| |
| #define PINT_2_BANK(x) ((x) >> 5) |
| #define PINT_2_BIT(x) ((x) & 0x1F) |
| #define PINT_BIT(x) (1 << (PINT_2_BIT(x))) |
| |
| static unsigned char irq2pint_lut[NR_PINTS]; |
| static unsigned char pint2irq_lut[NR_PINT_SYS_IRQS * NR_PINT_BITS]; |
| |
| struct pin_int_t { |
| unsigned int mask_set; |
| unsigned int mask_clear; |
| unsigned int request; |
| unsigned int assign; |
| unsigned int edge_set; |
| unsigned int edge_clear; |
| unsigned int invert_set; |
| unsigned int invert_clear; |
| unsigned int pinstate; |
| unsigned int latch; |
| }; |
| |
| static struct pin_int_t *pint[NR_PINT_SYS_IRQS] = { |
| (struct pin_int_t *)PINT0_MASK_SET, |
| (struct pin_int_t *)PINT1_MASK_SET, |
| (struct pin_int_t *)PINT2_MASK_SET, |
| (struct pin_int_t *)PINT3_MASK_SET, |
| }; |
| |
| inline unsigned int get_irq_base(u32 bank, u8 bmap) |
| { |
| unsigned int irq_base; |
| |
| if (bank < 2) { /*PA-PB */ |
| irq_base = IRQ_PA0 + bmap * 16; |
| } else { /*PC-PJ */ |
| irq_base = IRQ_PC0 + bmap * 16; |
| } |
| |
| return irq_base; |
| } |
| |
| /* Whenever PINTx_ASSIGN is altered init_pint_lut() must be executed! */ |
| void init_pint_lut(void) |
| { |
| u16 bank, bit, irq_base, bit_pos; |
| u32 pint_assign; |
| u8 bmap; |
| |
| memset(irq2pint_lut, IRQ_NOT_AVAIL, sizeof(irq2pint_lut)); |
| |
| for (bank = 0; bank < NR_PINT_SYS_IRQS; bank++) { |
| |
| pint_assign = pint[bank]->assign; |
| |
| for (bit = 0; bit < NR_PINT_BITS; bit++) { |
| |
| bmap = (pint_assign >> ((bit / 8) * 8)) & 0xFF; |
| |
| irq_base = get_irq_base(bank, bmap); |
| |
| irq_base += (bit % 8) + ((bit / 8) & 1 ? 8 : 0); |
| bit_pos = bit + bank * NR_PINT_BITS; |
| |
| pint2irq_lut[bit_pos] = irq_base - SYS_IRQS; |
| irq2pint_lut[irq_base - SYS_IRQS] = bit_pos; |
| } |
| } |
| } |
| |
| static void bfin_gpio_ack_irq(unsigned int irq) |
| { |
| struct irq_desc *desc = irq_desc + irq; |
| u32 pint_val = irq2pint_lut[irq - SYS_IRQS]; |
| u32 pintbit = PINT_BIT(pint_val); |
| u32 bank = PINT_2_BANK(pint_val); |
| |
| if ((desc->status & IRQ_TYPE_SENSE_MASK) == IRQ_TYPE_EDGE_BOTH) { |
| if (pint[bank]->invert_set & pintbit) |
| pint[bank]->invert_clear = pintbit; |
| else |
| pint[bank]->invert_set = pintbit; |
| } |
| pint[bank]->request = pintbit; |
| |
| } |
| |
| static void bfin_gpio_mask_ack_irq(unsigned int irq) |
| { |
| struct irq_desc *desc = irq_desc + irq; |
| u32 pint_val = irq2pint_lut[irq - SYS_IRQS]; |
| u32 pintbit = PINT_BIT(pint_val); |
| u32 bank = PINT_2_BANK(pint_val); |
| |
| if ((desc->status & IRQ_TYPE_SENSE_MASK) == IRQ_TYPE_EDGE_BOTH) { |
| if (pint[bank]->invert_set & pintbit) |
| pint[bank]->invert_clear = pintbit; |
| else |
| pint[bank]->invert_set = pintbit; |
| } |
| |
| pint[bank]->request = pintbit; |
| pint[bank]->mask_clear = pintbit; |
| } |
| |
| static void bfin_gpio_mask_irq(unsigned int irq) |
| { |
| u32 pint_val = irq2pint_lut[irq - SYS_IRQS]; |
| |
| pint[PINT_2_BANK(pint_val)]->mask_clear = PINT_BIT(pint_val); |
| } |
| |
| static void bfin_gpio_unmask_irq(unsigned int irq) |
| { |
| u32 pint_val = irq2pint_lut[irq - SYS_IRQS]; |
| u32 pintbit = PINT_BIT(pint_val); |
| u32 bank = PINT_2_BANK(pint_val); |
| |
| pint[bank]->request = pintbit; |
| pint[bank]->mask_set = pintbit; |
| } |
| |
| static unsigned int bfin_gpio_irq_startup(unsigned int irq) |
| { |
| u32 gpionr = irq_to_gpio(irq); |
| u32 pint_val = irq2pint_lut[irq - SYS_IRQS]; |
| |
| if (pint_val == IRQ_NOT_AVAIL) { |
| printk(KERN_ERR |
| "GPIO IRQ %d :Not in PINT Assign table " |
| "Reconfigure Interrupt to Port Assignemt\n", irq); |
| return -ENODEV; |
| } |
| |
| if (__test_and_set_bit(gpionr, gpio_enabled)) |
| bfin_gpio_irq_prepare(gpionr); |
| |
| bfin_gpio_unmask_irq(irq); |
| |
| return 0; |
| } |
| |
| static void bfin_gpio_irq_shutdown(unsigned int irq) |
| { |
| u32 gpionr = irq_to_gpio(irq); |
| |
| bfin_gpio_mask_irq(irq); |
| __clear_bit(gpionr, gpio_enabled); |
| bfin_gpio_irq_free(gpionr); |
| } |
| |
| static int bfin_gpio_irq_type(unsigned int irq, unsigned int type) |
| { |
| int ret; |
| char buf[16]; |
| u32 gpionr = irq_to_gpio(irq); |
| u32 pint_val = irq2pint_lut[irq - SYS_IRQS]; |
| u32 pintbit = PINT_BIT(pint_val); |
| u32 bank = PINT_2_BANK(pint_val); |
| |
| if (pint_val == IRQ_NOT_AVAIL) |
| return -ENODEV; |
| |
| if (type == IRQ_TYPE_PROBE) { |
| /* only probe unenabled GPIO interrupt lines */ |
| if (test_bit(gpionr, gpio_enabled)) |
| return 0; |
| type = IRQ_TYPE_EDGE_RISING | IRQ_TYPE_EDGE_FALLING; |
| } |
| |
| if (type & (IRQ_TYPE_EDGE_RISING | IRQ_TYPE_EDGE_FALLING | |
| IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_LEVEL_LOW)) { |
| |
| snprintf(buf, 16, "gpio-irq%d", irq); |
| ret = bfin_gpio_irq_request(gpionr, buf); |
| if (ret) |
| return ret; |
| |
| if (__test_and_set_bit(gpionr, gpio_enabled)) |
| bfin_gpio_irq_prepare(gpionr); |
| |
| } else { |
| __clear_bit(gpionr, gpio_enabled); |
| return 0; |
| } |
| |
| if ((type & (IRQ_TYPE_EDGE_FALLING | IRQ_TYPE_LEVEL_LOW))) |
| pint[bank]->invert_set = pintbit; /* low or falling edge denoted by one */ |
| else |
| pint[bank]->invert_clear = pintbit; /* high or rising edge denoted by zero */ |
| |
| if ((type & (IRQ_TYPE_EDGE_RISING | IRQ_TYPE_EDGE_FALLING)) |
| == (IRQ_TYPE_EDGE_RISING | IRQ_TYPE_EDGE_FALLING)) { |
| if (gpio_get_value(gpionr)) |
| pint[bank]->invert_set = pintbit; |
| else |
| pint[bank]->invert_clear = pintbit; |
| } |
| |
| if (type & (IRQ_TYPE_EDGE_RISING | IRQ_TYPE_EDGE_FALLING)) { |
| pint[bank]->edge_set = pintbit; |
| bfin_set_irq_handler(irq, handle_edge_irq); |
| } else { |
| pint[bank]->edge_clear = pintbit; |
| bfin_set_irq_handler(irq, handle_level_irq); |
| } |
| |
| return 0; |
| } |
| |
| #ifdef CONFIG_PM |
| u32 pint_saved_masks[NR_PINT_SYS_IRQS]; |
| u32 pint_wakeup_masks[NR_PINT_SYS_IRQS]; |
| |
| int bfin_gpio_set_wake(unsigned int irq, unsigned int state) |
| { |
| u32 pint_irq; |
| u32 pint_val = irq2pint_lut[irq - SYS_IRQS]; |
| u32 bank = PINT_2_BANK(pint_val); |
| u32 pintbit = PINT_BIT(pint_val); |
| |
| switch (bank) { |
| case 0: |
| pint_irq = IRQ_PINT0; |
| break; |
| case 2: |
| pint_irq = IRQ_PINT2; |
| break; |
| case 3: |
| pint_irq = IRQ_PINT3; |
| break; |
| case 1: |
| pint_irq = IRQ_PINT1; |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| bfin_internal_set_wake(pint_irq, state); |
| |
| if (state) |
| pint_wakeup_masks[bank] |= pintbit; |
| else |
| pint_wakeup_masks[bank] &= ~pintbit; |
| |
| return 0; |
| } |
| |
| u32 bfin_pm_setup(void) |
| { |
| u32 val, i; |
| |
| for (i = 0; i < NR_PINT_SYS_IRQS; i++) { |
| val = pint[i]->mask_clear; |
| pint_saved_masks[i] = val; |
| if (val ^ pint_wakeup_masks[i]) { |
| pint[i]->mask_clear = val; |
| pint[i]->mask_set = pint_wakeup_masks[i]; |
| } |
| } |
| |
| return 0; |
| } |
| |
| void bfin_pm_restore(void) |
| { |
| u32 i, val; |
| |
| for (i = 0; i < NR_PINT_SYS_IRQS; i++) { |
| val = pint_saved_masks[i]; |
| if (val ^ pint_wakeup_masks[i]) { |
| pint[i]->mask_clear = pint[i]->mask_clear; |
| pint[i]->mask_set = val; |
| } |
| } |
| } |
| #endif |
| |
| static void bfin_demux_gpio_irq(unsigned int inta_irq, |
| struct irq_desc *desc) |
| { |
| u32 bank, pint_val; |
| u32 request, irq; |
| |
| switch (inta_irq) { |
| case IRQ_PINT0: |
| bank = 0; |
| break; |
| case IRQ_PINT2: |
| bank = 2; |
| break; |
| case IRQ_PINT3: |
| bank = 3; |
| break; |
| case IRQ_PINT1: |
| bank = 1; |
| break; |
| default: |
| return; |
| } |
| |
| pint_val = bank * NR_PINT_BITS; |
| |
| request = pint[bank]->request; |
| |
| while (request) { |
| if (request & 1) { |
| irq = pint2irq_lut[pint_val] + SYS_IRQS; |
| bfin_handle_irq(irq); |
| } |
| pint_val++; |
| request >>= 1; |
| } |
| |
| } |
| #endif |
| |
| static struct irq_chip bfin_gpio_irqchip = { |
| .name = "GPIO", |
| .ack = bfin_gpio_ack_irq, |
| .mask = bfin_gpio_mask_irq, |
| .mask_ack = bfin_gpio_mask_ack_irq, |
| .unmask = bfin_gpio_unmask_irq, |
| .disable = bfin_gpio_mask_irq, |
| .enable = bfin_gpio_unmask_irq, |
| .set_type = bfin_gpio_irq_type, |
| .startup = bfin_gpio_irq_startup, |
| .shutdown = bfin_gpio_irq_shutdown, |
| #ifdef CONFIG_PM |
| .set_wake = bfin_gpio_set_wake, |
| #endif |
| }; |
| |
| void __cpuinit init_exception_vectors(void) |
| { |
| /* cannot program in software: |
| * evt0 - emulation (jtag) |
| * evt1 - reset |
| */ |
| bfin_write_EVT2(evt_nmi); |
| bfin_write_EVT3(trap); |
| bfin_write_EVT5(evt_ivhw); |
| bfin_write_EVT6(evt_timer); |
| bfin_write_EVT7(evt_evt7); |
| bfin_write_EVT8(evt_evt8); |
| bfin_write_EVT9(evt_evt9); |
| bfin_write_EVT10(evt_evt10); |
| bfin_write_EVT11(evt_evt11); |
| bfin_write_EVT12(evt_evt12); |
| bfin_write_EVT13(evt_evt13); |
| bfin_write_EVT14(evt_evt14); |
| bfin_write_EVT15(evt_system_call); |
| CSYNC(); |
| } |
| |
| /* |
| * This function should be called during kernel startup to initialize |
| * the BFin IRQ handling routines. |
| */ |
| |
| int __init init_arch_irq(void) |
| { |
| int irq; |
| unsigned long ilat = 0; |
| /* Disable all the peripheral intrs - page 4-29 HW Ref manual */ |
| #if defined(CONFIG_BF54x) || defined(CONFIG_BF52x) || defined(CONFIG_BF561) \ |
| || defined(BF538_FAMILY) || defined(CONFIG_BF51x) |
| bfin_write_SIC_IMASK0(SIC_UNMASK_ALL); |
| bfin_write_SIC_IMASK1(SIC_UNMASK_ALL); |
| # ifdef CONFIG_BF54x |
| bfin_write_SIC_IMASK2(SIC_UNMASK_ALL); |
| # endif |
| # ifdef CONFIG_SMP |
| bfin_write_SICB_IMASK0(SIC_UNMASK_ALL); |
| bfin_write_SICB_IMASK1(SIC_UNMASK_ALL); |
| # endif |
| #else |
| bfin_write_SIC_IMASK(SIC_UNMASK_ALL); |
| #endif |
| |
| local_irq_disable(); |
| |
| #if (defined(CONFIG_BF537) || defined(CONFIG_BF536)) |
| /* Clear EMAC Interrupt Status bits so we can demux it later */ |
| bfin_write_EMAC_SYSTAT(-1); |
| #endif |
| |
| #ifdef CONFIG_BF54x |
| # ifdef CONFIG_PINTx_REASSIGN |
| pint[0]->assign = CONFIG_PINT0_ASSIGN; |
| pint[1]->assign = CONFIG_PINT1_ASSIGN; |
| pint[2]->assign = CONFIG_PINT2_ASSIGN; |
| pint[3]->assign = CONFIG_PINT3_ASSIGN; |
| # endif |
| /* Whenever PINTx_ASSIGN is altered init_pint_lut() must be executed! */ |
| init_pint_lut(); |
| #endif |
| |
| for (irq = 0; irq <= SYS_IRQS; irq++) { |
| if (irq <= IRQ_CORETMR) |
| set_irq_chip(irq, &bfin_core_irqchip); |
| else |
| set_irq_chip(irq, &bfin_internal_irqchip); |
| |
| switch (irq) { |
| #if defined(CONFIG_BF53x) |
| case IRQ_PROG_INTA: |
| # if defined(BF537_FAMILY) && !(defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)) |
| case IRQ_MAC_RX: |
| # endif |
| #elif defined(CONFIG_BF54x) |
| case IRQ_PINT0: |
| case IRQ_PINT1: |
| case IRQ_PINT2: |
| case IRQ_PINT3: |
| #elif defined(CONFIG_BF52x) || defined(CONFIG_BF51x) |
| case IRQ_PORTF_INTA: |
| case IRQ_PORTG_INTA: |
| case IRQ_PORTH_INTA: |
| #elif defined(CONFIG_BF561) |
| case IRQ_PROG0_INTA: |
| case IRQ_PROG1_INTA: |
| case IRQ_PROG2_INTA: |
| #elif defined(CONFIG_BF538) || defined(CONFIG_BF539) |
| case IRQ_PORTF_INTA: |
| #endif |
| set_irq_chained_handler(irq, |
| bfin_demux_gpio_irq); |
| break; |
| #ifdef BF537_GENERIC_ERROR_INT_DEMUX |
| case IRQ_GENERIC_ERROR: |
| set_irq_chained_handler(irq, bfin_demux_error_irq); |
| break; |
| #endif |
| #if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE) |
| case IRQ_MAC_ERROR: |
| set_irq_chained_handler(irq, bfin_demux_mac_status_irq); |
| break; |
| #endif |
| #ifdef CONFIG_SMP |
| case IRQ_SUPPLE_0: |
| case IRQ_SUPPLE_1: |
| set_irq_handler(irq, handle_percpu_irq); |
| break; |
| #endif |
| |
| #ifdef CONFIG_TICKSOURCE_CORETMR |
| case IRQ_CORETMR: |
| # ifdef CONFIG_SMP |
| set_irq_handler(irq, handle_percpu_irq); |
| break; |
| # else |
| set_irq_handler(irq, handle_simple_irq); |
| break; |
| # endif |
| #endif |
| |
| #ifdef CONFIG_TICKSOURCE_GPTMR0 |
| case IRQ_TIMER0: |
| set_irq_handler(irq, handle_simple_irq); |
| break; |
| #endif |
| |
| #ifdef CONFIG_IPIPE |
| default: |
| set_irq_handler(irq, handle_level_irq); |
| break; |
| #else /* !CONFIG_IPIPE */ |
| default: |
| set_irq_handler(irq, handle_simple_irq); |
| break; |
| #endif /* !CONFIG_IPIPE */ |
| } |
| } |
| |
| #ifdef BF537_GENERIC_ERROR_INT_DEMUX |
| for (irq = IRQ_PPI_ERROR; irq <= IRQ_UART1_ERROR; irq++) |
| set_irq_chip_and_handler(irq, &bfin_generic_error_irqchip, |
| handle_level_irq); |
| #if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE) |
| set_irq_chained_handler(IRQ_MAC_ERROR, bfin_demux_mac_status_irq); |
| #endif |
| #endif |
| |
| #if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE) |
| for (irq = IRQ_MAC_PHYINT; irq <= IRQ_MAC_STMDONE; irq++) |
| set_irq_chip_and_handler(irq, &bfin_mac_status_irqchip, |
| handle_level_irq); |
| #endif |
| /* if configured as edge, then will be changed to do_edge_IRQ */ |
| for (irq = GPIO_IRQ_BASE; |
| irq < (GPIO_IRQ_BASE + MAX_BLACKFIN_GPIOS); irq++) |
| set_irq_chip_and_handler(irq, &bfin_gpio_irqchip, |
| handle_level_irq); |
| |
| bfin_write_IMASK(0); |
| CSYNC(); |
| ilat = bfin_read_ILAT(); |
| CSYNC(); |
| bfin_write_ILAT(ilat); |
| CSYNC(); |
| |
| printk(KERN_INFO "Configuring Blackfin Priority Driven Interrupts\n"); |
| /* IMASK=xxx is equivalent to STI xx or bfin_irq_flags=xx, |
| * local_irq_enable() |
| */ |
| program_IAR(); |
| /* Therefore it's better to setup IARs before interrupts enabled */ |
| search_IAR(); |
| |
| /* Enable interrupts IVG7-15 */ |
| bfin_irq_flags |= IMASK_IVG15 | |
| IMASK_IVG14 | IMASK_IVG13 | IMASK_IVG12 | IMASK_IVG11 | |
| IMASK_IVG10 | IMASK_IVG9 | IMASK_IVG8 | IMASK_IVG7 | IMASK_IVGHW; |
| |
| /* This implicitly covers ANOMALY_05000171 |
| * Boot-ROM code modifies SICA_IWRx wakeup registers |
| */ |
| #ifdef SIC_IWR0 |
| bfin_write_SIC_IWR0(IWR_DISABLE_ALL); |
| # ifdef SIC_IWR1 |
| /* BF52x/BF51x system reset does not properly reset SIC_IWR1 which |
| * will screw up the bootrom as it relies on MDMA0/1 waking it |
| * up from IDLE instructions. See this report for more info: |
| * http://blackfin.uclinux.org/gf/tracker/4323 |
| */ |
| if (ANOMALY_05000435) |
| bfin_write_SIC_IWR1(IWR_ENABLE(10) | IWR_ENABLE(11)); |
| else |
| bfin_write_SIC_IWR1(IWR_DISABLE_ALL); |
| # endif |
| # ifdef SIC_IWR2 |
| bfin_write_SIC_IWR2(IWR_DISABLE_ALL); |
| # endif |
| #else |
| bfin_write_SIC_IWR(IWR_DISABLE_ALL); |
| #endif |
| |
| return 0; |
| } |
| |
| #ifdef CONFIG_DO_IRQ_L1 |
| __attribute__((l1_text)) |
| #endif |
| void do_irq(int vec, struct pt_regs *fp) |
| { |
| if (vec == EVT_IVTMR_P) { |
| vec = IRQ_CORETMR; |
| } else { |
| struct ivgx *ivg = ivg7_13[vec - IVG7].ifirst; |
| struct ivgx *ivg_stop = ivg7_13[vec - IVG7].istop; |
| #if defined(SIC_ISR0) || defined(SICA_ISR0) |
| unsigned long sic_status[3]; |
| |
| if (smp_processor_id()) { |
| # ifdef SICB_ISR0 |
| /* This will be optimized out in UP mode. */ |
| sic_status[0] = bfin_read_SICB_ISR0() & bfin_read_SICB_IMASK0(); |
| sic_status[1] = bfin_read_SICB_ISR1() & bfin_read_SICB_IMASK1(); |
| # endif |
| } else { |
| sic_status[0] = bfin_read_SIC_ISR0() & bfin_read_SIC_IMASK0(); |
| sic_status[1] = bfin_read_SIC_ISR1() & bfin_read_SIC_IMASK1(); |
| } |
| # ifdef SIC_ISR2 |
| sic_status[2] = bfin_read_SIC_ISR2() & bfin_read_SIC_IMASK2(); |
| # endif |
| for (;; ivg++) { |
| if (ivg >= ivg_stop) { |
| atomic_inc(&num_spurious); |
| return; |
| } |
| if (sic_status[(ivg->irqno - IVG7) / 32] & ivg->isrflag) |
| break; |
| } |
| #else |
| unsigned long sic_status; |
| |
| sic_status = bfin_read_SIC_IMASK() & bfin_read_SIC_ISR(); |
| |
| for (;; ivg++) { |
| if (ivg >= ivg_stop) { |
| atomic_inc(&num_spurious); |
| return; |
| } else if (sic_status & ivg->isrflag) |
| break; |
| } |
| #endif |
| vec = ivg->irqno; |
| } |
| asm_do_IRQ(vec, fp); |
| } |
| |
| #ifdef CONFIG_IPIPE |
| |
| int __ipipe_get_irq_priority(unsigned irq) |
| { |
| int ient, prio; |
| |
| if (irq <= IRQ_CORETMR) |
| return irq; |
| |
| for (ient = 0; ient < NR_PERI_INTS; ient++) { |
| struct ivgx *ivg = ivg_table + ient; |
| if (ivg->irqno == irq) { |
| for (prio = 0; prio <= IVG13-IVG7; prio++) { |
| if (ivg7_13[prio].ifirst <= ivg && |
| ivg7_13[prio].istop > ivg) |
| return IVG7 + prio; |
| } |
| } |
| } |
| |
| return IVG15; |
| } |
| |
| /* Hw interrupts are disabled on entry (check SAVE_CONTEXT). */ |
| #ifdef CONFIG_DO_IRQ_L1 |
| __attribute__((l1_text)) |
| #endif |
| asmlinkage int __ipipe_grab_irq(int vec, struct pt_regs *regs) |
| { |
| struct ipipe_percpu_domain_data *p = ipipe_root_cpudom_ptr(); |
| struct ipipe_domain *this_domain = __ipipe_current_domain; |
| struct ivgx *ivg_stop = ivg7_13[vec-IVG7].istop; |
| struct ivgx *ivg = ivg7_13[vec-IVG7].ifirst; |
| int irq, s; |
| |
| if (likely(vec == EVT_IVTMR_P)) |
| irq = IRQ_CORETMR; |
| else { |
| #if defined(SIC_ISR0) || defined(SICA_ISR0) |
| unsigned long sic_status[3]; |
| |
| sic_status[0] = bfin_read_SIC_ISR0() & bfin_read_SIC_IMASK0(); |
| sic_status[1] = bfin_read_SIC_ISR1() & bfin_read_SIC_IMASK1(); |
| # ifdef SIC_ISR2 |
| sic_status[2] = bfin_read_SIC_ISR2() & bfin_read_SIC_IMASK2(); |
| # endif |
| for (;; ivg++) { |
| if (ivg >= ivg_stop) { |
| atomic_inc(&num_spurious); |
| return 0; |
| } |
| if (sic_status[(ivg->irqno - IVG7) / 32] & ivg->isrflag) |
| break; |
| } |
| #else |
| unsigned long sic_status; |
| |
| sic_status = bfin_read_SIC_IMASK() & bfin_read_SIC_ISR(); |
| |
| for (;; ivg++) { |
| if (ivg >= ivg_stop) { |
| atomic_inc(&num_spurious); |
| return 0; |
| } else if (sic_status & ivg->isrflag) |
| break; |
| } |
| #endif |
| irq = ivg->irqno; |
| } |
| |
| if (irq == IRQ_SYSTMR) { |
| #if !defined(CONFIG_GENERIC_CLOCKEVENTS) || defined(CONFIG_TICKSOURCE_GPTMR0) |
| bfin_write_TIMER_STATUS(1); /* Latch TIMIL0 */ |
| #endif |
| /* This is basically what we need from the register frame. */ |
| __raw_get_cpu_var(__ipipe_tick_regs).ipend = regs->ipend; |
| __raw_get_cpu_var(__ipipe_tick_regs).pc = regs->pc; |
| if (this_domain != ipipe_root_domain) |
| __raw_get_cpu_var(__ipipe_tick_regs).ipend &= ~0x10; |
| else |
| __raw_get_cpu_var(__ipipe_tick_regs).ipend |= 0x10; |
| } |
| |
| if (this_domain == ipipe_root_domain) { |
| s = __test_and_set_bit(IPIPE_SYNCDEFER_FLAG, &p->status); |
| barrier(); |
| } |
| |
| ipipe_trace_irq_entry(irq); |
| __ipipe_handle_irq(irq, regs); |
| ipipe_trace_irq_exit(irq); |
| |
| if (this_domain == ipipe_root_domain) { |
| set_thread_flag(TIF_IRQ_SYNC); |
| if (!s) { |
| __clear_bit(IPIPE_SYNCDEFER_FLAG, &p->status); |
| return !test_bit(IPIPE_STALL_FLAG, &p->status); |
| } |
| } |
| |
| return 0; |
| } |
| |
| #endif /* CONFIG_IPIPE */ |