arch/arm/mach-orion5x/ls_hgl-setup.c

/*
 * arch/arm/mach-orion5x/ls_hgl-setup.c
 *
 * Maintainer: Zhu Qingsen <zhuqs@cn.fujitsu.com>
 *
 * This file is licensed under the terms of the GNU General Public
 * License version 2.  This program is licensed "as is" without any
 * warranty of any kind, whether express or implied.
 */

#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/mtd/physmap.h>
#include <linux/mv643xx_eth.h>
#include <linux/leds.h>
#include <linux/gpio_keys.h>
#include <linux/input.h>
#include <linux/i2c.h>
#include <linux/ata_platform.h>
#include <linux/gpio.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/system.h>
#include <mach/orion5x.h>
#include "common.h"
#include "mpp.h"

/*****************************************************************************
 * Linkstation LS-HGL Info
 ****************************************************************************/

/*
 * 256K NOR flash Device bus boot chip select
 */

#define LS_HGL_NOR_BOOT_BASE	0xf4000000
#define LS_HGL_NOR_BOOT_SIZE	SZ_256K

/*****************************************************************************
 * 256KB NOR Flash on BOOT Device
 ****************************************************************************/

static struct physmap_flash_data ls_hgl_nor_flash_data = {
	.width		= 1,
};

static struct resource ls_hgl_nor_flash_resource = {
	.flags	= IORESOURCE_MEM,
	.start	= LS_HGL_NOR_BOOT_BASE,
	.end	= LS_HGL_NOR_BOOT_BASE + LS_HGL_NOR_BOOT_SIZE - 1,
};

static struct platform_device ls_hgl_nor_flash = {
	.name			= "physmap-flash",
	.id			= 0,
	.dev		= {
		.platform_data	= &ls_hgl_nor_flash_data,
	},
	.num_resources		= 1,
	.resource		= &ls_hgl_nor_flash_resource,
};

/*****************************************************************************
 * Ethernet
 ****************************************************************************/

static struct mv643xx_eth_platform_data ls_hgl_eth_data = {
	.phy_addr	= 8,
};

/*****************************************************************************
 * RTC 5C372a on I2C bus
 ****************************************************************************/

static struct i2c_board_info __initdata ls_hgl_i2c_rtc = {
	I2C_BOARD_INFO("rs5c372a", 0x32),
};

/*****************************************************************************
 * LEDs attached to GPIO
 ****************************************************************************/

#define LS_HGL_GPIO_LED_ALARM   2
#define LS_HGL_GPIO_LED_INFO    3
#define LS_HGL_GPIO_LED_FUNC    17
#define LS_HGL_GPIO_LED_PWR     0


static struct gpio_led ls_hgl_led_pins[] = {
	{
		.name	   = "alarm:red",
		.gpio	   = LS_HGL_GPIO_LED_ALARM,
		.active_low     = 1,
	}, {
		.name	   = "info:amber",
		.gpio	   = LS_HGL_GPIO_LED_INFO,
		.active_low     = 1,
	}, {
		.name	   = "func:blue:top",
		.gpio	   = LS_HGL_GPIO_LED_FUNC,
		.active_low     = 1,
	}, {
		.name	   = "power:blue:bottom",
		.gpio	   = LS_HGL_GPIO_LED_PWR,
	},
};

static struct gpio_led_platform_data ls_hgl_led_data = {
	.leds	   = ls_hgl_led_pins,
	.num_leds       = ARRAY_SIZE(ls_hgl_led_pins),
};

static struct platform_device ls_hgl_leds = {
	.name   = "leds-gpio",
	.id     = -1,
	.dev    = {
		.platform_data  = &ls_hgl_led_data,
	},
};

/****************************************************************************
 * GPIO Attached Keys
 ****************************************************************************/
#define LS_HGL_GPIO_KEY_FUNC       15
#define LS_HGL_GPIO_KEY_POWER      8
#define LS_HGL_GPIO_KEY_AUTOPOWER  10

#define LS_HGL_SW_POWER     0x00
#define LS_HGL_SW_AUTOPOWER 0x01

static struct gpio_keys_button ls_hgl_buttons[] = {
	{
		.code	   = KEY_OPTION,
		.gpio	   = LS_HGL_GPIO_KEY_FUNC,
		.desc	   = "Function Button",
		.active_low     = 1,
	}, {
		.type		= EV_SW,
		.code	   = LS_HGL_SW_POWER,
		.gpio	   = LS_HGL_GPIO_KEY_POWER,
		.desc	   = "Power-on Switch",
		.active_low     = 1,
	}, {
		.type		= EV_SW,
		.code	   = LS_HGL_SW_AUTOPOWER,
		.gpio	   = LS_HGL_GPIO_KEY_AUTOPOWER,
		.desc	   = "Power-auto Switch",
		.active_low     = 1,
	},
};

static struct gpio_keys_platform_data ls_hgl_button_data = {
	.buttons	= ls_hgl_buttons,
	.nbuttons       = ARRAY_SIZE(ls_hgl_buttons),
};

static struct platform_device ls_hgl_button_device = {
	.name	   = "gpio-keys",
	.id	     = -1,
	.num_resources  = 0,
	.dev	    = {
		.platform_data  = &ls_hgl_button_data,
	},
};


/*****************************************************************************
 * SATA
 ****************************************************************************/
static struct mv_sata_platform_data ls_hgl_sata_data = {
	.n_ports	= 2,
};


/*****************************************************************************
 * Linkstation LS-HGL specific power off method: reboot
 ****************************************************************************/
/*
 * On the Linkstation LS-HGL, the shutdown process is following:
 * - Userland monitors key events until the power switch goes to off position
 * - The board reboots
 * - U-boot starts and goes into an idle mode waiting for the user
 *   to move the switch to ON position
 */

static void ls_hgl_power_off(void)
{
	arm_machine_restart('h', NULL);
}


/*****************************************************************************
 * General Setup
 ****************************************************************************/

#define LS_HGL_GPIO_USB_POWER	9
#define LS_HGL_GPIO_AUTO_POWER	10
#define LS_HGL_GPIO_POWER	    8

#define LS_HGL_GPIO_HDD_POWER	1

static struct orion5x_mpp_mode ls_hgl_mpp_modes[] __initdata = {
	{  0, MPP_GPIO }, /* LED_PWR */
	{  1, MPP_GPIO }, /* HDD_PWR */
	{  2, MPP_GPIO }, /* LED_ALARM */
	{  3, MPP_GPIO }, /* LED_INFO */
	{  4, MPP_UNUSED },
	{  5, MPP_UNUSED },
	{  6, MPP_GPIO }, /* FAN_LCK */
	{  7, MPP_GPIO }, /* INIT */
	{  8, MPP_GPIO }, /* POWER */
	{  9, MPP_GPIO }, /* USB_PWR */
	{ 10, MPP_GPIO }, /* AUTO_POWER */
	{ 11, MPP_UNUSED }, /* LED_ETH (dummy) */
	{ 12, MPP_UNUSED },
	{ 13, MPP_UNUSED },
	{ 14, MPP_UNUSED },
	{ 15, MPP_GPIO }, /* FUNC */
	{ 16, MPP_UNUSED },
	{ 17, MPP_GPIO }, /* LED_FUNC */
	{ 18, MPP_UNUSED },
	{ 19, MPP_UNUSED },
	{ -1 },
};

static void __init ls_hgl_init(void)
{
	/*
	 * Setup basic Orion functions. Need to be called early.
	 */
	orion5x_init();

	orion5x_mpp_conf(ls_hgl_mpp_modes);

	/*
	 * Configure peripherals.
	 */
	orion5x_ehci0_init();
	orion5x_ehci1_init();
	orion5x_eth_init(&ls_hgl_eth_data);
	orion5x_i2c_init();
	orion5x_sata_init(&ls_hgl_sata_data);
	orion5x_uart0_init();
	orion5x_xor_init();

	orion5x_setup_dev_boot_win(LS_HGL_NOR_BOOT_BASE,
				   LS_HGL_NOR_BOOT_SIZE);
	platform_device_register(&ls_hgl_nor_flash);

	platform_device_register(&ls_hgl_button_device);

	platform_device_register(&ls_hgl_leds);

	i2c_register_board_info(0, &ls_hgl_i2c_rtc, 1);

	/* enable USB power */
	gpio_set_value(LS_HGL_GPIO_USB_POWER, 1);

	/* register power-off method */
	pm_power_off = ls_hgl_power_off;

	pr_info("%s: finished\n", __func__);
}

MACHINE_START(LINKSTATION_LS_HGL, "Buffalo Linkstation LS-HGL")
	/* Maintainer: Zhu Qingsen <zhuqs@cn.fujistu.com> */
	.phys_io	= ORION5X_REGS_PHYS_BASE,
	.io_pg_offst	= ((ORION5X_REGS_VIRT_BASE) >> 18) & 0xFFFC,
	.boot_params	= 0x00000100,
	.init_machine	= ls_hgl_init,
	.map_io		= orion5x_map_io,
	.init_irq	= orion5x_init_irq,
	.timer		= &orion5x_timer,
	.fixup		= tag_fixup_mem32,
MACHINE_END