#!/vendor/bin/sh
# Copyright (c) 2012-2018, 2020-2021 The Linux Foundation. All rights reserved.
#
# Redistribution and use in source and binary forms, with or without
# modification, are permitted provided that the following conditions are
# met:
#     * Redistributions of source code must retain the above copyright
#       notice, this list of conditions and the following disclaimer.
#     * Redistributions in binary form must reproduce the above
#       copyright notice, this list of conditions and the following
#       disclaimer in the documentation and/or other materials provided
#       with the distribution.
#     * Neither the name of The Linux Foundation nor the names of its
#       contributors may be used to endorse or promote products derived
#      from this software without specific prior written permission.
#
# THIS SOFTWARE IS PROVIDED "AS IS" AND ANY EXPRESS OR IMPLIED
# WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
# MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT
# ARE DISCLAIMED.  IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS
# BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
# CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
# SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
# BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
# WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
# OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN
# IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
#
#

# Set platform variables
soc_hwplatform=`cat /sys/devices/soc0/hw_platform 2> /dev/null`
soc_machine=`cat /sys/devices/soc0/machine 2> /dev/null`
soc_machine=${soc_machine:0:2}
soc_id=`cat /sys/devices/soc0/soc_id 2> /dev/null`

#
# Check ESOC for external modem
#
# Note: currently only a single MDM/SDX is supported
#
esoc_name=`cat /sys/bus/esoc/devices/esoc0/esoc_name 2> /dev/null`

target=`getprop ro.board.platform`

#
# Override USB default composition
#
# If USB persist config not set, set default configuration
if [ "$(getprop persist.vendor.usb.config)" == "" -a "$(getprop ro.build.type)" != "user" ]; then
    if [ "$esoc_name" != "" ]; then
	  setprop persist.vendor.usb.config diag,diag_mdm,qdss,qdss_mdm,serial_cdev,dpl,rmnet,adb
    else
	  case "$(getprop ro.baseband)" in
	      "apq")
	          setprop persist.vendor.usb.config diag,adb
	      ;;
	      *)
	      case "$soc_hwplatform" in
	          "Dragon" | "SBC")
	              setprop persist.vendor.usb.config diag,adb
	          ;;
                  *)
		  case "$soc_machine" in
		    "SA")
	              setprop persist.vendor.usb.config diag,adb
		    ;;
		    *)
	            case "$target" in
	              "msm8996")
	                  setprop persist.vendor.usb.config diag,serial_cdev,serial_tty,rmnet_ipa,mass_storage,adb
		      ;;
	              "msm8909")
		          setprop persist.vendor.usb.config diag,serial_smd,rmnet_qti_bam,adb
		      ;;
	              "msm8937")
			    if [ -d /config/usb_gadget ]; then
				       setprop persist.vendor.usb.config diag,serial_cdev,rmnet,dpl,adb
			    else
			               case "$soc_id" in
				               "313" | "320")
				                  setprop persist.vendor.usb.config diag,serial_smd,rmnet_ipa,adb
				               ;;
				               *)
				                  setprop persist.vendor.usb.config diag,serial_smd,rmnet_qti_bam,adb
				               ;;
			               esac
			    fi
		      ;;
	              "msm8953")
			      if [ -d /config/usb_gadget ]; then
				      setprop persist.vendor.usb.config diag,serial_cdev,rmnet,dpl,adb
			      else
				      setprop persist.vendor.usb.config diag,serial_smd,rmnet_ipa,adb
			      fi
		      ;;
	              "msm8998" | "sdm660" | "apq8098_latv")
		          setprop persist.vendor.usb.config diag,serial_cdev,rmnet,adb
		      ;;
	              "sdm845" | "sdm710")
		          setprop persist.vendor.usb.config diag,serial_cdev,rmnet,dpl,adb
		      ;;
	              "msmnile" | "sm6150" | "trinket" | "lito" | "atoll" | "bengal" | "lahaina" | "holi" | "taro" | "parrot")
			  setprop persist.vendor.usb.config diag,serial_cdev,rmnet,dpl,qdss,adb
		      ;;
	              *)
		          setprop persist.vendor.usb.config diag,adb
		      ;;
                    esac
		    ;;
		  esac
	          ;;
	      esac
	      ;;
	  esac
      fi
fi

# This check is needed for GKI 1.0 targets where QDSS is not available
if [ "$(getprop persist.vendor.usb.config)" == "diag,serial_cdev,rmnet,dpl,qdss,adb" -a \
     ! -d /config/usb_gadget/g1/functions/qdss.qdss ]; then
      setprop persist.vendor.usb.config diag,serial_cdev,rmnet,dpl,adb
fi

# Start peripheral mode on primary USB controllers for Automotive platforms
case "$soc_machine" in
    "SA")
	if [ -f /sys/bus/platform/devices/a600000.ssusb/mode ]; then
	    default_mode=`cat /sys/bus/platform/devices/a600000.ssusb/mode`
	    case "$default_mode" in
		"none")
		    echo peripheral > /sys/bus/platform/devices/a600000.ssusb/mode
		;;
	    esac
	fi
    ;;
esac

# check configfs is mounted or not
if [ -d /config/usb_gadget ]; then
	# Chip-serial is used for unique MSM identification in Product string
	msm_serial=`cat /sys/devices/soc0/serial_number`;
	# If MSM serial number is not available, then keep it blank instead of 0x00000000
	if [ "$msm_serial" != "" ]; then
		msm_serial_hex=`printf %08X $msm_serial`
	fi

	machine_type=`cat /sys/devices/soc0/machine`
	setprop vendor.usb.product_string "$machine_type-$soc_hwplatform _SN:$msm_serial_hex"

	# ADB requires valid iSerialNumber; if ro.serialno is missing, use dummy
	serialnumber=`cat /config/usb_gadget/g1/strings/0x409/serialnumber 2> /dev/null`
	if [ "$serialnumber" == "" ]; then
		serialno=1234567
		echo $serialno > /config/usb_gadget/g1/strings/0x409/serialnumber
	fi
	setprop vendor.usb.configfs 1
fi

#
# Initialize RNDIS Diag option. If unset, set it to 'none'.
#
diag_extra=`getprop persist.vendor.usb.config.extra`
if [ "$diag_extra" == "" ]; then
	setprop persist.vendor.usb.config.extra none
fi

# enable rps cpus on msm8937 target
setprop vendor.usb.rps_mask 0
case "$soc_id" in
	"294" | "295" | "353" | "354")
		setprop vendor.usb.rps_mask 40
	;;
esac

#
# Initialize UVC conifguration.
#
if [ -d /config/usb_gadget/g1/functions/uvc.0 ]; then
	setprop vendor.usb.uvc.function.init 1
fi