Usage

Two options to use the hid command:

1. Interactive through stdin:

type hid - into the terminal, then type/paste commands to send to the binary. Use Ctrl+D to signal end of stream to the binary (EOF).

This mode can be also used from an app to send HID events. For an example, see the cts test case at: InputTestCase.java

When using another program to control hid in interactive mode, registering a new input device (for example, a bluetooth joystick) should be the first step. After the device is added, you need to wait for the onInputDeviceAdded (see InputDeviceListener) notification before issuing commands to the device. Failure to do so will cause missed events and inconsistent behaviour. In the current implementation of the hid command, the hid binary will wait for the file descriptor to the uhid node to send the UHID_START and UHID_OPEN signals before returning. However, this is not sufficient. These signals only notify the readiness of the kernel driver, but do not take into account the inputflinger framework.

2. Using a file as an input:

type hid <filename>, and the file will be used an an input to the binary. You must add a sufficient delay after a "register" command to ensure device is ready. The interactive mode is the recommended method of communicating with the hid binary.

All of the input commands should be in pseudo-JSON format as documented below. See examples here.

The file can have multiple commands one after the other (which is not strictly legal JSON format, as this would imply multiple root elements).

Command description

1. register Register a new uhid device

Device ID is used for matching the subsequent commands to a specific device to avoid ambiguity when multiple devices are registered.

Device bus is used to determine how the uhid device is connected to the host. The options are "usb" and "bluetooth".

USB HID report descriptor should be generated according the the USB HID spec and can be checked by reverse parsing using a variety of tools, for example usbdescreqparser.

Example:

{
  "id": 1,
  "command": "register",
  "name": "Odie (Test)",
  "vid": 0x18d1,
  "pid": 0x2c40,
  "bus": "usb",
  "descriptor": [0x05, 0x01, 0x09, 0x05, 0xa1, 0x01, 0x85, 0x01, 0x05, 0x09, 0x0a, 0x01, 0x00,
    0x0a, 0x02, 0x00, 0x0a, 0x04, 0x00, 0x0a, 0x05, 0x00, 0x0a, 0x07, 0x00, 0x0a, 0x08, 0x00,
    0x0a, 0x0e, 0x00, 0x0a, 0x0f, 0x00, 0x0a, 0x0d, 0x00, 0x05, 0x0c, 0x0a, 0x24, 0x02, 0x0a,
    0x23, 0x02, 0x15, 0x00, 0x25, 0x01, 0x75, 0x01, 0x95, 0x0b, 0x81, 0x02, 0x75, 0x01, 0x95,
    0x01, 0x81, 0x03, 0x05, 0x01, 0x75, 0x04, 0x95, 0x01, 0x25, 0x07, 0x46, 0x3b, 0x01, 0x66,
    0x14, 0x00, 0x09, 0x39, 0x81, 0x42, 0x66, 0x00, 0x00, 0x09, 0x01, 0xa1, 0x00, 0x09, 0x30,
    0x09, 0x31, 0x09, 0x32, 0x09, 0x35, 0x05, 0x02, 0x09, 0xc5, 0x09, 0xc4, 0x15, 0x00, 0x26,
    0xff, 0x00, 0x35, 0x00, 0x46, 0xff, 0x00, 0x75, 0x08, 0x95, 0x06, 0x81, 0x02, 0xc0, 0x85,
    0x02, 0x05, 0x08, 0x0a, 0x01, 0x00, 0x0a, 0x02, 0x00, 0x0a, 0x03, 0x00, 0x0a, 0x04, 0x00,
    0x15, 0x00, 0x25, 0x01, 0x75, 0x01, 0x95, 0x04, 0x91, 0x02, 0x75, 0x04, 0x95, 0x01, 0x91,
    0x03, 0xc0, 0x05, 0x0c, 0x09, 0x01, 0xa1, 0x01, 0x85, 0x03, 0x05, 0x01, 0x09, 0x06, 0xa1,
    0x02, 0x05, 0x06, 0x09, 0x20, 0x15, 0x00, 0x26, 0xff, 0x00, 0x75, 0x08, 0x95, 0x01, 0x81,
    0x02, 0x06, 0xbc, 0xff, 0x0a, 0xad, 0xbd, 0x75, 0x08, 0x95, 0x06, 0x81, 0x02, 0xc0, 0xc0]
}

2. delay Add a delay to command processing

Example:

{
  "id": 1,
  "command": "delay",
  "duration": 10
}

3. report Send a report to the HID device

Example:

{
  "id": 1,
  "command": "report",
  "report": [0x01, 0x01, 0x80, 0x7f, 0x7f, 0x7f, 0x7f, 0x00, 0x00]
}

Sending a joystick button press event

To send a button press event on a joystick device:

1. Register the joystick device
2. Send button down event with coordinates ABS_X, ABS_Y, ABS_Z, and ABS_RZ at the center of the range. If the coordinates are not centered, this event will generate a motion event within the input framework, in addition to the button press event. The range can be determined from the uhid report descriptor.
3. Send the button up event with the same coordinates as in 2.
4. Check that the button press event was received.

Notes

1. As soon as EOF is reached (either in interactive mode, or in file mode), the device that was created will be unregistered. There is no explicit command for unregistering a device.
2. The linux input subsystem does not generate events for those values that remain unchanged. For example, if there are two events sent to the driver, and both events have the same value of ABS_X, then ABS_X coordinate will not be reported.
3. The description of joystick actions is available here.
4. Joysticks are split axes. When an analog stick is in a resting state, the reported coordinates are at the center of the range.
5. The getevent utility can used to print out the key events for debugging purposes.