diff --git a/MAINTAINERS b/MAINTAINERS
index 90dcbbc..87bdced 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -4343,6 +4343,16 @@
 W:	http://oops.ghostprotocols.net:81/blog
 S:	Maintained
 
+WM97XX TOUCHSCREEN DRIVERS
+P:	Mark Brown
+M:	broonie@opensource.wolfsonmicro.com
+P:	Liam Girdwood
+M:	liam.girdwood@wolfsonmicro.com
+L:	linux-input@vger.kernel.org
+T:	git git://opensource.wolfsonmicro.com/linux-2.6-touch
+W:	http://opensource.wolfsonmicro.com/node/7
+S:	Supported
+
 X.25 NETWORK LAYER
 P:	Henner Eisen
 M:	eis@baty.hanse.de
diff --git a/drivers/input/touchscreen/Kconfig b/drivers/input/touchscreen/Kconfig
index 90e8e92..a95a87c 100644
--- a/drivers/input/touchscreen/Kconfig
+++ b/drivers/input/touchscreen/Kconfig
@@ -185,6 +185,20 @@
 	  To compile this driver as a module, choose M here: the
 	  module will be called ucb1400_ts.
 
+config TOUCHSCREEN_WM97XX
+	tristate "Support for WM97xx AC97 touchscreen controllers"
+	depends on AC97_BUS
+	help
+	  Say Y here if you have a Wolfson Microelectronics WM97xx
+	  touchscreen connected to your system. Note that this option
+	  only enables core driver, you will also need to select
+	  support for appropriate chip below.
+
+	  If unsure, say N.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called wm97xx-ts.
+
 config TOUCHSCREEN_USB_COMPOSITE
 	tristate "USB Touchscreen Driver"
 	depends on USB_ARCH_HAS_HCD
diff --git a/drivers/input/touchscreen/Makefile b/drivers/input/touchscreen/Makefile
index 35d4097..b4e7b5d 100644
--- a/drivers/input/touchscreen/Makefile
+++ b/drivers/input/touchscreen/Makefile
@@ -4,6 +4,8 @@
 
 # Each configuration option enables a list of files.
 
+wm97xx-ts-y := wm97xx-core.o
+
 obj-$(CONFIG_TOUCHSCREEN_ADS7846)	+= ads7846.o
 obj-$(CONFIG_TOUCHSCREEN_BITSY)		+= h3600_ts_input.o
 obj-$(CONFIG_TOUCHSCREEN_CORGI)		+= corgi_ts.o
@@ -19,3 +21,4 @@
 obj-$(CONFIG_TOUCHSCREEN_TOUCHRIGHT)	+= touchright.o
 obj-$(CONFIG_TOUCHSCREEN_TOUCHWIN)	+= touchwin.o
 obj-$(CONFIG_TOUCHSCREEN_UCB1400)	+= ucb1400_ts.o
+obj-$(CONFIG_TOUCHSCREEN_WM97XX)	+= wm97xx-ts.o
diff --git a/drivers/input/touchscreen/wm97xx-core.c b/drivers/input/touchscreen/wm97xx-core.c
new file mode 100644
index 0000000..2910999
--- /dev/null
+++ b/drivers/input/touchscreen/wm97xx-core.c
@@ -0,0 +1,789 @@
+/*
+ * wm97xx-core.c  --  Touch screen driver core for Wolfson WM9705, WM9712
+ *                    and WM9713 AC97 Codecs.
+ *
+ * Copyright 2003, 2004, 2005, 2006, 2007, 2008 Wolfson Microelectronics PLC.
+ * Author: Liam Girdwood
+ *         liam.girdwood@wolfsonmicro.com or linux@wolfsonmicro.com
+ * Parts Copyright : Ian Molton <spyro@f2s.com>
+ *                   Andrew Zabolotny <zap@homelink.ru>
+ *                   Russell King <rmk@arm.linux.org.uk>
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ *
+ * Notes:
+ *
+ *  Features:
+ *       - supports WM9705, WM9712, WM9713
+ *       - polling mode
+ *       - continuous mode (arch-dependent)
+ *       - adjustable rpu/dpp settings
+ *       - adjustable pressure current
+ *       - adjustable sample settle delay
+ *       - 4 and 5 wire touchscreens (5 wire is WM9712 only)
+ *       - pen down detection
+ *       - battery monitor
+ *       - sample AUX adcs
+ *       - power management
+ *       - codec GPIO
+ *       - codec event notification
+ * Todo
+ *       - Support for async sampling control for noisy LCDs.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/version.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/string.h>
+#include <linux/proc_fs.h>
+#include <linux/pm.h>
+#include <linux/interrupt.h>
+#include <linux/bitops.h>
+#include <linux/workqueue.h>
+#include <linux/wm97xx.h>
+#include <linux/uaccess.h>
+#include <linux/io.h>
+
+#define TS_NAME			"wm97xx"
+#define WM_CORE_VERSION		"1.00"
+#define DEFAULT_PRESSURE	0xb0c0
+
+
+/*
+ * Touchscreen absolute values
+ *
+ * These parameters are used to help the input layer discard out of
+ * range readings and reduce jitter etc.
+ *
+ *   o min, max:- indicate the min and max values your touch screen returns
+ *   o fuzz:- use a higher number to reduce jitter
+ *
+ * The default values correspond to Mainstone II in QVGA mode
+ *
+ * Please read
+ * Documentation/input/input-programming.txt for more details.
+ */
+
+static int abs_x[3] = {350, 3900, 5};
+module_param_array(abs_x, int, NULL, 0);
+MODULE_PARM_DESC(abs_x, "Touchscreen absolute X min, max, fuzz");
+
+static int abs_y[3] = {320, 3750, 40};
+module_param_array(abs_y, int, NULL, 0);
+MODULE_PARM_DESC(abs_y, "Touchscreen absolute Y min, max, fuzz");
+
+static int abs_p[3] = {0, 150, 4};
+module_param_array(abs_p, int, NULL, 0);
+MODULE_PARM_DESC(abs_p, "Touchscreen absolute Pressure min, max, fuzz");
+
+/*
+ * wm97xx IO access, all IO locking done by AC97 layer
+ */
+int wm97xx_reg_read(struct wm97xx *wm, u16 reg)
+{
+	if (wm->ac97)
+		return wm->ac97->bus->ops->read(wm->ac97, reg);
+	else
+		return -1;
+}
+EXPORT_SYMBOL_GPL(wm97xx_reg_read);
+
+void wm97xx_reg_write(struct wm97xx *wm, u16 reg, u16 val)
+{
+	/* cache digitiser registers */
+	if (reg >= AC97_WM9713_DIG1 && reg <= AC97_WM9713_DIG3)
+		wm->dig[(reg - AC97_WM9713_DIG1) >> 1] = val;
+
+	/* cache gpio regs */
+	if (reg >= AC97_GPIO_CFG && reg <= AC97_MISC_AFE)
+		wm->gpio[(reg - AC97_GPIO_CFG) >> 1] = val;
+
+	/* wm9713 irq reg */
+	if (reg == 0x5a)
+		wm->misc = val;
+
+	if (wm->ac97)
+		wm->ac97->bus->ops->write(wm->ac97, reg, val);
+}
+EXPORT_SYMBOL_GPL(wm97xx_reg_write);
+
+/**
+ * wm97xx_read_aux_adc - Read the aux adc.
+ * @wm: wm97xx device.
+ * @adcsel: codec ADC to be read
+ *
+ * Reads the selected AUX ADC.
+ */
+
+int wm97xx_read_aux_adc(struct wm97xx *wm, u16 adcsel)
+{
+	int power_adc = 0, auxval;
+	u16 power = 0;
+
+	/* get codec */
+	mutex_lock(&wm->codec_mutex);
+
+	/* When the touchscreen is not in use, we may have to power up
+	 * the AUX ADC before we can use sample the AUX inputs->
+	 */
+	if (wm->id == WM9713_ID2 &&
+	    (power = wm97xx_reg_read(wm, AC97_EXTENDED_MID)) & 0x8000) {
+		power_adc = 1;
+		wm97xx_reg_write(wm, AC97_EXTENDED_MID, power & 0x7fff);
+	}
+
+	/* Prepare the codec for AUX reading */
+	wm->codec->aux_prepare(wm);
+
+	/* Turn polling mode on to read AUX ADC */
+	wm->pen_probably_down = 1;
+	wm->codec->poll_sample(wm, adcsel, &auxval);
+
+	if (power_adc)
+		wm97xx_reg_write(wm, AC97_EXTENDED_MID, power | 0x8000);
+
+	wm->codec->dig_restore(wm);
+
+	wm->pen_probably_down = 0;
+
+	mutex_unlock(&wm->codec_mutex);
+	return auxval & 0xfff;
+}
+EXPORT_SYMBOL_GPL(wm97xx_read_aux_adc);
+
+/**
+ * wm97xx_get_gpio - Get the status of a codec GPIO.
+ * @wm: wm97xx device.
+ * @gpio: gpio
+ *
+ * Get the status of a codec GPIO pin
+ */
+
+enum wm97xx_gpio_status wm97xx_get_gpio(struct wm97xx *wm, u32 gpio)
+{
+	u16 status;
+	enum wm97xx_gpio_status ret;
+
+	mutex_lock(&wm->codec_mutex);
+	status = wm97xx_reg_read(wm, AC97_GPIO_STATUS);
+
+	if (status & gpio)
+		ret = WM97XX_GPIO_HIGH;
+	else
+		ret = WM97XX_GPIO_LOW;
+
+	mutex_unlock(&wm->codec_mutex);
+	return ret;
+}
+EXPORT_SYMBOL_GPL(wm97xx_get_gpio);
+
+/**
+ * wm97xx_set_gpio - Set the status of a codec GPIO.
+ * @wm: wm97xx device.
+ * @gpio: gpio
+ *
+ *
+ * Set the status of a codec GPIO pin
+ */
+
+void wm97xx_set_gpio(struct wm97xx *wm, u32 gpio,
+				enum wm97xx_gpio_status status)
+{
+	u16 reg;
+
+	mutex_lock(&wm->codec_mutex);
+	reg = wm97xx_reg_read(wm, AC97_GPIO_STATUS);
+
+	if (status & WM97XX_GPIO_HIGH)
+		reg |= gpio;
+	else
+		reg &= ~gpio;
+
+	if (wm->id == WM9712_ID2)
+		wm97xx_reg_write(wm, AC97_GPIO_STATUS, reg << 1);
+	else
+		wm97xx_reg_write(wm, AC97_GPIO_STATUS, reg);
+	mutex_unlock(&wm->codec_mutex);
+}
+EXPORT_SYMBOL_GPL(wm97xx_set_gpio);
+
+/*
+ * Codec GPIO pin configuration, this sets pin direction, polarity,
+ * stickyness and wake up.
+ */
+void wm97xx_config_gpio(struct wm97xx *wm, u32 gpio, enum wm97xx_gpio_dir dir,
+		   enum wm97xx_gpio_pol pol, enum wm97xx_gpio_sticky sticky,
+		   enum wm97xx_gpio_wake wake)
+{
+	u16 reg;
+
+	mutex_lock(&wm->codec_mutex);
+	reg = wm97xx_reg_read(wm, AC97_GPIO_POLARITY);
+
+	if (pol == WM97XX_GPIO_POL_HIGH)
+		reg |= gpio;
+	else
+		reg &= ~gpio;
+
+	wm97xx_reg_write(wm, AC97_GPIO_POLARITY, reg);
+	reg = wm97xx_reg_read(wm, AC97_GPIO_STICKY);
+
+	if (sticky == WM97XX_GPIO_STICKY)
+		reg |= gpio;
+	else
+		reg &= ~gpio;
+
+	wm97xx_reg_write(wm, AC97_GPIO_STICKY, reg);
+	reg = wm97xx_reg_read(wm, AC97_GPIO_WAKEUP);
+
+	if (wake == WM97XX_GPIO_WAKE)
+		reg |= gpio;
+	else
+		reg &= ~gpio;
+
+	wm97xx_reg_write(wm, AC97_GPIO_WAKEUP, reg);
+	reg = wm97xx_reg_read(wm, AC97_GPIO_CFG);
+
+	if (dir == WM97XX_GPIO_IN)
+		reg |= gpio;
+	else
+		reg &= ~gpio;
+
+	wm97xx_reg_write(wm, AC97_GPIO_CFG, reg);
+	mutex_unlock(&wm->codec_mutex);
+}
+EXPORT_SYMBOL_GPL(wm97xx_config_gpio);
+
+/*
+ * Handle a pen down interrupt.
+ */
+static void wm97xx_pen_irq_worker(struct work_struct *work)
+{
+	struct wm97xx *wm = container_of(work, struct wm97xx, pen_event_work);
+	int pen_was_down = wm->pen_is_down;
+
+	/* do we need to enable the touch panel reader */
+	if (wm->id == WM9705_ID2) {
+		if (wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD) &
+					WM97XX_PEN_DOWN)
+			wm->pen_is_down = 1;
+		else
+			wm->pen_is_down = 0;
+	} else {
+		u16 status, pol;
+		mutex_lock(&wm->codec_mutex);
+		status = wm97xx_reg_read(wm, AC97_GPIO_STATUS);
+		pol = wm97xx_reg_read(wm, AC97_GPIO_POLARITY);
+
+		if (WM97XX_GPIO_13 & pol & status) {
+			wm->pen_is_down = 1;
+			wm97xx_reg_write(wm, AC97_GPIO_POLARITY, pol &
+						~WM97XX_GPIO_13);
+		} else {
+			wm->pen_is_down = 0;
+			wm97xx_reg_write(wm, AC97_GPIO_POLARITY, pol |
+					 WM97XX_GPIO_13);
+		}
+
+		if (wm->id == WM9712_ID2)
+			wm97xx_reg_write(wm, AC97_GPIO_STATUS, (status &
+						~WM97XX_GPIO_13) << 1);
+		else
+			wm97xx_reg_write(wm, AC97_GPIO_STATUS, status &
+						~WM97XX_GPIO_13);
+		mutex_unlock(&wm->codec_mutex);
+	}
+
+	/* If the system is not using continuous mode or it provides a
+	 * pen down operation then we need to schedule polls while the
+	 * pen is down.  Otherwise the machine driver is responsible
+	 * for scheduling reads.
+	 */
+	if (!wm->mach_ops->acc_enabled || wm->mach_ops->acc_pen_down) {
+		if (wm->pen_is_down && !pen_was_down) {
+			/* Data is not availiable immediately on pen down */
+			queue_delayed_work(wm->ts_workq, &wm->ts_reader, 1);
+		}
+
+		/* Let ts_reader report the pen up for debounce. */
+		if (!wm->pen_is_down && pen_was_down)
+			wm->pen_is_down = 1;
+	}
+
+	if (!wm->pen_is_down && wm->mach_ops->acc_enabled)
+		wm->mach_ops->acc_pen_up(wm);
+
+	wm->mach_ops->irq_enable(wm, 1);
+}
+
+/*
+ * Codec PENDOWN irq handler
+ *
+ * We have to disable the codec interrupt in the handler because it
+ * can take upto 1ms to clear the interrupt source. We schedule a task
+ * in a work queue to do the actual interaction with the chip (it
+ * doesn't matter if we end up reenqueing it before it is executed
+ * since we don't touch the chip until it has run).  The interrupt is
+ * then enabled again in the slow handler when the source has been
+ * cleared.
+ */
+static irqreturn_t wm97xx_pen_interrupt(int irq, void *dev_id)
+{
+	struct wm97xx *wm = dev_id;
+
+	wm->mach_ops->irq_enable(wm, 0);
+	queue_work(wm->ts_workq, &wm->pen_event_work);
+
+	return IRQ_HANDLED;
+}
+
+/*
+ * initialise pen IRQ handler and workqueue
+ */
+static int wm97xx_init_pen_irq(struct wm97xx *wm)
+{
+	u16 reg;
+
+	/* If an interrupt is supplied an IRQ enable operation must also be
+	 * provided. */
+	BUG_ON(!wm->mach_ops->irq_enable);
+
+	if (request_irq(wm->pen_irq, wm97xx_pen_interrupt, IRQF_SHARED,
+			"wm97xx-pen", wm)) {
+		dev_err(wm->dev,
+			"Failed to register pen down interrupt, polling");
+		wm->pen_irq = 0;
+		return -EINVAL;
+	}
+
+	/* Configure GPIO as interrupt source on WM971x */
+	if (wm->id != WM9705_ID2) {
+		BUG_ON(!wm->mach_ops->irq_gpio);
+		reg = wm97xx_reg_read(wm, AC97_MISC_AFE);
+		wm97xx_reg_write(wm, AC97_MISC_AFE,
+				reg & ~(wm->mach_ops->irq_gpio));
+		reg = wm97xx_reg_read(wm, 0x5a);
+		wm97xx_reg_write(wm, 0x5a, reg & ~0x0001);
+	}
+
+	return 0;
+}
+
+static int wm97xx_read_samples(struct wm97xx *wm)
+{
+	struct wm97xx_data data;
+	int rc;
+
+	mutex_lock(&wm->codec_mutex);
+
+	if (wm->mach_ops && wm->mach_ops->acc_enabled)
+		rc = wm->mach_ops->acc_pen_down(wm);
+	else
+		rc = wm->codec->poll_touch(wm, &data);
+
+	if (rc & RC_PENUP) {
+		if (wm->pen_is_down) {
+			wm->pen_is_down = 0;
+			dev_dbg(wm->dev, "pen up\n");
+			input_report_abs(wm->input_dev, ABS_PRESSURE, 0);
+			input_sync(wm->input_dev);
+		} else if (!(rc & RC_AGAIN)) {
+			/* We need high frequency updates only while
+			* pen is down, the user never will be able to
+			* touch screen faster than a few times per
+			* second... On the other hand, when the user
+			* is actively working with the touchscreen we
+			* don't want to lose the quick response. So we
+			* will slowly increase sleep time after the
+			* pen is up and quicky restore it to ~one task
+			* switch when pen is down again.
+			*/
+			if (wm->ts_reader_interval < HZ / 10)
+				wm->ts_reader_interval++;
+		}
+
+	} else if (rc & RC_VALID) {
+		dev_dbg(wm->dev,
+			"pen down: x=%x:%d, y=%x:%d, pressure=%x:%d\n",
+			data.x >> 12, data.x & 0xfff, data.y >> 12,
+			data.y & 0xfff, data.p >> 12, data.p & 0xfff);
+		input_report_abs(wm->input_dev, ABS_X, data.x & 0xfff);
+		input_report_abs(wm->input_dev, ABS_Y, data.y & 0xfff);
+		input_report_abs(wm->input_dev, ABS_PRESSURE, data.p & 0xfff);
+		input_sync(wm->input_dev);
+		wm->pen_is_down = 1;
+		wm->ts_reader_interval = wm->ts_reader_min_interval;
+	} else if (rc & RC_PENDOWN) {
+		dev_dbg(wm->dev, "pen down\n");
+		wm->pen_is_down = 1;
+		wm->ts_reader_interval = wm->ts_reader_min_interval;
+	}
+
+	mutex_unlock(&wm->codec_mutex);
+	return rc;
+}
+
+/*
+* The touchscreen sample reader.
+*/
+static void wm97xx_ts_reader(struct work_struct *work)
+{
+	int rc;
+	struct wm97xx *wm = container_of(work, struct wm97xx, ts_reader.work);
+
+	BUG_ON(!wm->codec);
+
+	do {
+		rc = wm97xx_read_samples(wm);
+	} while (rc & RC_AGAIN);
+
+	if (wm->pen_is_down || !wm->pen_irq)
+		queue_delayed_work(wm->ts_workq, &wm->ts_reader,
+				   wm->ts_reader_interval);
+}
+
+/**
+ * wm97xx_ts_input_open - Open the touch screen input device.
+ * @idev:	Input device to be opened.
+ *
+ * Called by the input sub system to open a wm97xx touchscreen device.
+ * Starts the touchscreen thread and touch digitiser.
+ */
+static int wm97xx_ts_input_open(struct input_dev *idev)
+{
+	struct wm97xx *wm = input_get_drvdata(idev);
+
+	wm->ts_workq = create_singlethread_workqueue("kwm97xx");
+	if (wm->ts_workq == NULL) {
+		dev_err(wm->dev,
+			"Failed to create workqueue\n");
+		return -EINVAL;
+	}
+
+	/* start digitiser */
+	if (wm->mach_ops && wm->mach_ops->acc_enabled)
+		wm->codec->acc_enable(wm, 1);
+	wm->codec->dig_enable(wm, 1);
+
+	INIT_DELAYED_WORK(&wm->ts_reader, wm97xx_ts_reader);
+	INIT_WORK(&wm->pen_event_work, wm97xx_pen_irq_worker);
+
+	wm->ts_reader_min_interval = HZ >= 100 ? HZ / 100 : 1;
+	if (wm->ts_reader_min_interval < 1)
+		wm->ts_reader_min_interval = 1;
+	wm->ts_reader_interval = wm->ts_reader_min_interval;
+
+	wm->pen_is_down = 0;
+	if (wm->pen_irq)
+		wm97xx_init_pen_irq(wm);
+	else
+		dev_err(wm->dev, "No IRQ specified\n");
+
+	/* If we either don't have an interrupt for pen down events or
+	 * failed to acquire it then we need to poll.
+	 */
+	if (wm->pen_irq == 0)
+		queue_delayed_work(wm->ts_workq, &wm->ts_reader,
+				   wm->ts_reader_interval);
+
+	return 0;
+}
+
+/**
+ * wm97xx_ts_input_close - Close the touch screen input device.
+ * @idev:	Input device to be closed.
+ *
+ * Called by the input sub system to close a wm97xx touchscreen
+ * device.  Kills the touchscreen thread and stops the touch
+ * digitiser.
+ */
+
+static void wm97xx_ts_input_close(struct input_dev *idev)
+{
+	struct wm97xx *wm = input_get_drvdata(idev);
+	u16 reg;
+
+	if (wm->pen_irq) {
+		/* Return the interrupt to GPIO usage (disabling it) */
+		if (wm->id != WM9705_ID2) {
+			BUG_ON(!wm->mach_ops->irq_gpio);
+			reg = wm97xx_reg_read(wm, AC97_MISC_AFE);
+			wm97xx_reg_write(wm, AC97_MISC_AFE,
+					 reg | wm->mach_ops->irq_gpio);
+		}
+
+		free_irq(wm->pen_irq, wm);
+	}
+
+	wm->pen_is_down = 0;
+
+	/* Balance out interrupt disables/enables */
+	if (cancel_work_sync(&wm->pen_event_work))
+		wm->mach_ops->irq_enable(wm, 1);
+
+	/* ts_reader rearms itself so we need to explicitly stop it
+	 * before we destroy the workqueue.
+	 */
+	cancel_delayed_work_sync(&wm->ts_reader);
+
+	destroy_workqueue(wm->ts_workq);
+
+	/* stop digitiser */
+	wm->codec->dig_enable(wm, 0);
+	if (wm->mach_ops && wm->mach_ops->acc_enabled)
+		wm->codec->acc_enable(wm, 0);
+}
+
+static int wm97xx_probe(struct device *dev)
+{
+	struct wm97xx *wm;
+	int ret = 0, id = 0;
+
+	wm = kzalloc(sizeof(struct wm97xx), GFP_KERNEL);
+	if (!wm)
+		return -ENOMEM;
+	mutex_init(&wm->codec_mutex);
+
+	wm->dev = dev;
+	dev->driver_data = wm;
+	wm->ac97 = to_ac97_t(dev);
+
+	/* check that we have a supported codec */
+	id = wm97xx_reg_read(wm, AC97_VENDOR_ID1);
+	if (id != WM97XX_ID1) {
+		dev_err(dev, "Device with vendor %04x is not a wm97xx\n", id);
+		ret = -ENODEV;
+		goto alloc_err;
+	}
+
+	wm->id = wm97xx_reg_read(wm, AC97_VENDOR_ID2);
+
+	dev_info(wm->dev, "detected a wm97%02x codec\n", wm->id & 0xff);
+
+	switch (wm->id & 0xff) {
+#ifdef CONFIG_TOUCHSCREEN_WM9705
+	case 0x05:
+		wm->codec = &wm9705_codec;
+		break;
+#endif
+#ifdef CONFIG_TOUCHSCREEN_WM9712
+	case 0x12:
+		wm->codec = &wm9712_codec;
+		break;
+#endif
+#ifdef CONFIG_TOUCHSCREEN_WM9713
+	case 0x13:
+		wm->codec = &wm9713_codec;
+		break;
+#endif
+	default:
+		dev_err(wm->dev, "Support for wm97%02x not compiled in.\n",
+			wm->id & 0xff);
+		ret = -ENODEV;
+		goto alloc_err;
+	}
+
+	wm->input_dev = input_allocate_device();
+	if (wm->input_dev == NULL) {
+		ret = -ENOMEM;
+		goto alloc_err;
+	}
+
+	/* set up touch configuration */
+	wm->input_dev->name = "wm97xx touchscreen";
+	wm->input_dev->open = wm97xx_ts_input_open;
+	wm->input_dev->close = wm97xx_ts_input_close;
+	set_bit(EV_ABS, wm->input_dev->evbit);
+	set_bit(ABS_X, wm->input_dev->absbit);
+	set_bit(ABS_Y, wm->input_dev->absbit);
+	set_bit(ABS_PRESSURE, wm->input_dev->absbit);
+	input_set_abs_params(wm->input_dev, ABS_X, abs_x[0], abs_x[1],
+			     abs_x[2], 0);
+	input_set_abs_params(wm->input_dev, ABS_Y, abs_y[0], abs_y[1],
+			     abs_y[2], 0);
+	input_set_abs_params(wm->input_dev, ABS_PRESSURE, abs_p[0], abs_p[1],
+			     abs_p[2], 0);
+	input_set_drvdata(wm->input_dev, wm);
+	wm->input_dev->dev.parent = dev;
+	ret = input_register_device(wm->input_dev);
+	if (ret < 0)
+		goto dev_alloc_err;
+
+	/* set up physical characteristics */
+	wm->codec->phy_init(wm);
+
+	/* load gpio cache */
+	wm->gpio[0] = wm97xx_reg_read(wm, AC97_GPIO_CFG);
+	wm->gpio[1] = wm97xx_reg_read(wm, AC97_GPIO_POLARITY);
+	wm->gpio[2] = wm97xx_reg_read(wm, AC97_GPIO_STICKY);
+	wm->gpio[3] = wm97xx_reg_read(wm, AC97_GPIO_WAKEUP);
+	wm->gpio[4] = wm97xx_reg_read(wm, AC97_GPIO_STATUS);
+	wm->gpio[5] = wm97xx_reg_read(wm, AC97_MISC_AFE);
+
+	/* register our battery device */
+	wm->battery_dev = platform_device_alloc("wm97xx-battery", -1);
+	if (!wm->battery_dev) {
+		ret = -ENOMEM;
+		goto batt_err;
+	}
+	platform_set_drvdata(wm->battery_dev, wm);
+	wm->battery_dev->dev.parent = dev;
+	ret = platform_device_add(wm->battery_dev);
+	if (ret < 0)
+		goto batt_reg_err;
+
+	/* register our extended touch device (for machine specific
+	 * extensions) */
+	wm->touch_dev = platform_device_alloc("wm97xx-touch", -1);
+	if (!wm->touch_dev) {
+		ret = -ENOMEM;
+		goto touch_err;
+	}
+	platform_set_drvdata(wm->touch_dev, wm);
+	wm->touch_dev->dev.parent = dev;
+	ret = platform_device_add(wm->touch_dev);
+	if (ret < 0)
+		goto touch_reg_err;
+
+	return ret;
+
+ touch_reg_err:
+	platform_device_put(wm->touch_dev);
+ touch_err:
+	platform_device_unregister(wm->battery_dev);
+	wm->battery_dev = NULL;
+ batt_reg_err:
+	platform_device_put(wm->battery_dev);
+ batt_err:
+	input_unregister_device(wm->input_dev);
+	wm->input_dev = NULL;
+ dev_alloc_err:
+	input_free_device(wm->input_dev);
+ alloc_err:
+	kfree(wm);
+
+	return ret;
+}
+
+static int wm97xx_remove(struct device *dev)
+{
+	struct wm97xx *wm = dev_get_drvdata(dev);
+
+	platform_device_unregister(wm->battery_dev);
+	platform_device_unregister(wm->touch_dev);
+	input_unregister_device(wm->input_dev);
+	kfree(wm);
+
+	return 0;
+}
+
+#ifdef CONFIG_PM
+static int wm97xx_suspend(struct device *dev, pm_message_t state)
+{
+	struct wm97xx *wm = dev_get_drvdata(dev);
+
+	if (wm->input_dev->users)
+		cancel_delayed_work_sync(&wm->ts_reader);
+
+	return 0;
+}
+
+static int wm97xx_resume(struct device *dev)
+{
+	struct wm97xx *wm = dev_get_drvdata(dev);
+
+	/* restore digitiser and gpios */
+	if (wm->id == WM9713_ID2) {
+		wm97xx_reg_write(wm, AC97_WM9713_DIG1, wm->dig[0]);
+		wm97xx_reg_write(wm, 0x5a, wm->misc);
+		if (wm->input_dev->users) {
+			u16 reg;
+			reg = wm97xx_reg_read(wm, AC97_EXTENDED_MID) & 0x7fff;
+			wm97xx_reg_write(wm, AC97_EXTENDED_MID, reg);
+		}
+	}
+
+	wm97xx_reg_write(wm, AC97_WM9713_DIG2, wm->dig[1]);
+	wm97xx_reg_write(wm, AC97_WM9713_DIG3, wm->dig[2]);
+
+	wm97xx_reg_write(wm, AC97_GPIO_CFG, wm->gpio[0]);
+	wm97xx_reg_write(wm, AC97_GPIO_POLARITY, wm->gpio[1]);
+	wm97xx_reg_write(wm, AC97_GPIO_STICKY, wm->gpio[2]);
+	wm97xx_reg_write(wm, AC97_GPIO_WAKEUP, wm->gpio[3]);
+	wm97xx_reg_write(wm, AC97_GPIO_STATUS, wm->gpio[4]);
+	wm97xx_reg_write(wm, AC97_MISC_AFE, wm->gpio[5]);
+
+	if (wm->input_dev->users && !wm->pen_irq) {
+		wm->ts_reader_interval = wm->ts_reader_min_interval;
+		queue_delayed_work(wm->ts_workq, &wm->ts_reader,
+				   wm->ts_reader_interval);
+	}
+
+	return 0;
+}
+
+#else
+#define wm97xx_suspend		NULL
+#define wm97xx_resume		NULL
+#endif
+
+/*
+ * Machine specific operations
+ */
+int wm97xx_register_mach_ops(struct wm97xx *wm,
+			     struct wm97xx_mach_ops *mach_ops)
+{
+	mutex_lock(&wm->codec_mutex);
+	if (wm->mach_ops) {
+		mutex_unlock(&wm->codec_mutex);
+		return -EINVAL;
+	}
+	wm->mach_ops = mach_ops;
+	mutex_unlock(&wm->codec_mutex);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(wm97xx_register_mach_ops);
+
+void wm97xx_unregister_mach_ops(struct wm97xx *wm)
+{
+	mutex_lock(&wm->codec_mutex);
+	wm->mach_ops = NULL;
+	mutex_unlock(&wm->codec_mutex);
+}
+EXPORT_SYMBOL_GPL(wm97xx_unregister_mach_ops);
+
+static struct device_driver wm97xx_driver = {
+	.name =		"ac97",
+	.bus =		&ac97_bus_type,
+	.owner =	THIS_MODULE,
+	.probe =	wm97xx_probe,
+	.remove =	wm97xx_remove,
+	.suspend =	wm97xx_suspend,
+	.resume =	wm97xx_resume,
+};
+
+static int __init wm97xx_init(void)
+{
+	return driver_register(&wm97xx_driver);
+}
+
+static void __exit wm97xx_exit(void)
+{
+	driver_unregister(&wm97xx_driver);
+}
+
+module_init(wm97xx_init);
+module_exit(wm97xx_exit);
+
+/* Module information */
+MODULE_AUTHOR("Liam Girdwood <liam.girdwood@wolfsonmicro.com>");
+MODULE_DESCRIPTION("WM97xx Core - Touch Screen / AUX ADC / GPIO Driver");
+MODULE_LICENSE("GPL");
diff --git a/include/linux/wm97xx.h b/include/linux/wm97xx.h
new file mode 100644
index 0000000..ed01c7d
--- /dev/null
+++ b/include/linux/wm97xx.h
@@ -0,0 +1,311 @@
+
+/*
+ * Register bits and API for Wolfson WM97xx series of codecs
+ */
+
+#ifndef _LINUX_WM97XX_H
+#define _LINUX_WM97XX_H
+
+#include <sound/core.h>
+#include <sound/pcm.h>
+#include <sound/ac97_codec.h>
+#include <sound/initval.h>
+#include <linux/types.h>
+#include <linux/list.h>
+#include <linux/input.h>	/* Input device layer */
+#include <linux/platform_device.h>
+
+/*
+ * WM97xx AC97 Touchscreen registers
+ */
+#define AC97_WM97XX_DIGITISER1		0x76
+#define AC97_WM97XX_DIGITISER2		0x78
+#define AC97_WM97XX_DIGITISER_RD 	0x7a
+#define AC97_WM9713_DIG1		0x74
+#define AC97_WM9713_DIG2		AC97_WM97XX_DIGITISER1
+#define AC97_WM9713_DIG3		AC97_WM97XX_DIGITISER2
+
+/*
+ * WM97xx register bits
+ */
+#define WM97XX_POLL		0x8000	/* initiate a polling measurement */
+#define WM97XX_ADCSEL_X		0x1000	/* x coord measurement */
+#define WM97XX_ADCSEL_Y		0x2000	/* y coord measurement */
+#define WM97XX_ADCSEL_PRES	0x3000	/* pressure measurement */
+#define WM97XX_ADCSEL_MASK	0x7000
+#define WM97XX_COO		0x0800	/* enable coordinate mode */
+#define WM97XX_CTC		0x0400	/* enable continuous mode */
+#define WM97XX_CM_RATE_93	0x0000	/* 93.75Hz continuous rate */
+#define WM97XX_CM_RATE_187	0x0100	/* 187.5Hz continuous rate */
+#define WM97XX_CM_RATE_375	0x0200	/* 375Hz continuous rate */
+#define WM97XX_CM_RATE_750	0x0300	/* 750Hz continuous rate */
+#define WM97XX_CM_RATE_8K	0x00f0	/* 8kHz continuous rate */
+#define WM97XX_CM_RATE_12K	0x01f0	/* 12kHz continuous rate */
+#define WM97XX_CM_RATE_24K	0x02f0	/* 24kHz continuous rate */
+#define WM97XX_CM_RATE_48K	0x03f0	/* 48kHz continuous rate */
+#define WM97XX_CM_RATE_MASK	0x03f0
+#define WM97XX_RATE(i)		(((i & 3) << 8) | ((i & 4) ? 0xf0 : 0))
+#define WM97XX_DELAY(i)		((i << 4) & 0x00f0)	/* sample delay times */
+#define WM97XX_DELAY_MASK	0x00f0
+#define WM97XX_SLEN		0x0008	/* slot read back enable */
+#define WM97XX_SLT(i)		((i - 5) & 0x7)	/* panel slot (5-11) */
+#define WM97XX_SLT_MASK		0x0007
+#define WM97XX_PRP_DETW		0x4000	/* detect on, digitise off, wake */
+#define WM97XX_PRP_DET		0x8000	/* detect on, digitise off, no wake */
+#define WM97XX_PRP_DET_DIG	0xc000	/* setect on, digitise on */
+#define WM97XX_RPR		0x2000	/* wake up on pen down */
+#define WM97XX_PEN_DOWN		0x8000	/* pen is down */
+#define WM97XX_ADCSRC_MASK	0x7000	/* ADC source mask */
+
+#define WM97XX_AUX_ID1		0x8001
+#define WM97XX_AUX_ID2		0x8002
+#define WM97XX_AUX_ID3		0x8003
+#define WM97XX_AUX_ID4		0x8004
+
+
+/* WM9712 Bits */
+#define WM9712_45W		0x1000	/* set for 5-wire touchscreen */
+#define WM9712_PDEN		0x0800	/* measure only when pen down */
+#define WM9712_WAIT		0x0200	/* wait until adc is read before next sample */
+#define WM9712_PIL		0x0100	/* current used for pressure measurement. set 400uA else 200uA */
+#define WM9712_MASK_HI		0x0040	/* hi on mask pin (47) stops conversions */
+#define WM9712_MASK_EDGE	0x0080	/* rising/falling edge on pin delays sample */
+#define	WM9712_MASK_SYNC	0x00c0	/* rising/falling edge on mask initiates sample */
+#define WM9712_RPU(i)		(i&0x3f)	/* internal pull up on pen detect (64k / rpu) */
+#define WM9712_PD(i)		(0x1 << i)	/* power management */
+
+/* WM9712 Registers */
+#define AC97_WM9712_POWER	0x24
+#define AC97_WM9712_REV		0x58
+
+/* WM9705 Bits */
+#define WM9705_PDEN		0x1000	/* measure only when pen is down */
+#define WM9705_PINV		0x0800	/* inverts sense of pen down output */
+#define WM9705_BSEN		0x0400	/* BUSY flag enable, pin47 is 1 when busy */
+#define WM9705_BINV		0x0200	/* invert BUSY (pin47) output */
+#define WM9705_WAIT		0x0100	/* wait until adc is read before next sample */
+#define WM9705_PIL		0x0080	/* current used for pressure measurement. set 400uA else 200uA */
+#define WM9705_PHIZ		0x0040	/* set PHONE and PCBEEP inputs to high impedance */
+#define WM9705_MASK_HI		0x0010	/* hi on mask stops conversions */
+#define WM9705_MASK_EDGE	0x0020	/* rising/falling edge on pin delays sample */
+#define	WM9705_MASK_SYNC	0x0030	/* rising/falling edge on mask initiates sample */
+#define WM9705_PDD(i)		(i & 0x000f)	/* pen detect comparator threshold */
+
+
+/* WM9713 Bits */
+#define WM9713_PDPOL		0x0400	/* Pen down polarity */
+#define WM9713_POLL		0x0200	/* initiate a polling measurement */
+#define WM9713_CTC		0x0100	/* enable continuous mode */
+#define WM9713_ADCSEL_X		0x0002	/* X measurement */
+#define WM9713_ADCSEL_Y		0x0004	/* Y measurement */
+#define WM9713_ADCSEL_PRES	0x0008	/* Pressure measurement */
+#define WM9713_COO		0x0001	/* enable coordinate mode */
+#define WM9713_PDEN		0x0800	/* measure only when pen down */
+#define WM9713_ADCSEL_MASK	0x00fe	/* ADC selection mask */
+#define WM9713_WAIT		0x0200	/* coordinate wait */
+
+/* AUX ADC ID's */
+#define TS_COMP1		0x0
+#define TS_COMP2		0x1
+#define TS_BMON			0x2
+#define TS_WIPER		0x3
+
+/* ID numbers */
+#define WM97XX_ID1		0x574d
+#define WM9712_ID2		0x4c12
+#define WM9705_ID2		0x4c05
+#define WM9713_ID2		0x4c13
+
+/* Codec GPIO's */
+#define WM97XX_MAX_GPIO		16
+#define WM97XX_GPIO_1		(1 << 1)
+#define WM97XX_GPIO_2		(1 << 2)
+#define WM97XX_GPIO_3		(1 << 3)
+#define WM97XX_GPIO_4		(1 << 4)
+#define WM97XX_GPIO_5		(1 << 5)
+#define WM97XX_GPIO_6		(1 << 6)
+#define WM97XX_GPIO_7		(1 << 7)
+#define WM97XX_GPIO_8		(1 << 8)
+#define WM97XX_GPIO_9		(1 << 9)
+#define WM97XX_GPIO_10		(1 << 10)
+#define WM97XX_GPIO_11		(1 << 11)
+#define WM97XX_GPIO_12		(1 << 12)
+#define WM97XX_GPIO_13		(1 << 13)
+#define WM97XX_GPIO_14		(1 << 14)
+#define WM97XX_GPIO_15		(1 << 15)
+
+
+#define AC97_LINK_FRAME		21	/* time in uS for AC97 link frame */
+
+
+/*---------------- Return codes from sample reading functions ---------------*/
+
+/* More data is available; call the sample gathering function again */
+#define RC_AGAIN			0x00000001
+/* The returned sample is valid */
+#define RC_VALID			0x00000002
+/* The pen is up (the first RC_VALID without RC_PENUP means pen is down) */
+#define RC_PENUP			0x00000004
+/* The pen is down (RC_VALID implies RC_PENDOWN, but sometimes it is helpful
+   to tell the handler that the pen is down but we don't know yet his coords,
+   so the handler should not sleep or wait for pendown irq) */
+#define RC_PENDOWN			0x00000008
+
+/*
+ * The wm97xx driver provides a private API for writing platform-specific
+ * drivers.
+ */
+
+/* The structure used to return arch specific sampled data into */
+struct wm97xx_data {
+    int x;
+    int y;
+    int p;
+};
+
+/*
+ * Codec GPIO status
+ */
+enum wm97xx_gpio_status {
+    WM97XX_GPIO_HIGH,
+    WM97XX_GPIO_LOW
+};
+
+/*
+ * Codec GPIO direction
+ */
+enum wm97xx_gpio_dir {
+    WM97XX_GPIO_IN,
+    WM97XX_GPIO_OUT
+};
+
+/*
+ * Codec GPIO polarity
+ */
+enum wm97xx_gpio_pol {
+    WM97XX_GPIO_POL_HIGH,
+    WM97XX_GPIO_POL_LOW
+};
+
+/*
+ * Codec GPIO sticky
+ */
+enum wm97xx_gpio_sticky {
+    WM97XX_GPIO_STICKY,
+    WM97XX_GPIO_NOTSTICKY
+};
+
+/*
+ * Codec GPIO wake
+ */
+enum wm97xx_gpio_wake {
+    WM97XX_GPIO_WAKE,
+    WM97XX_GPIO_NOWAKE
+};
+
+/*
+ * Digitiser ioctl commands
+ */
+#define WM97XX_DIG_START	0x1
+#define WM97XX_DIG_STOP		0x2
+#define WM97XX_PHY_INIT		0x3
+#define WM97XX_AUX_PREPARE	0x4
+#define WM97XX_DIG_RESTORE	0x5
+
+struct wm97xx;
+
+extern struct wm97xx_codec_drv wm9705_codec;
+extern struct wm97xx_codec_drv wm9712_codec;
+extern struct wm97xx_codec_drv wm9713_codec;
+
+/*
+ * Codec driver interface - allows mapping to WM9705/12/13 and newer codecs
+ */
+struct wm97xx_codec_drv {
+	u16 id;
+	char *name;
+
+	/* read 1 sample */
+	int (*poll_sample) (struct wm97xx *, int adcsel, int *sample);
+
+	/* read X,Y,[P] in poll */
+	int (*poll_touch) (struct wm97xx *, struct wm97xx_data *);
+
+	int (*acc_enable) (struct wm97xx *, int enable);
+	void (*phy_init) (struct wm97xx *);
+	void (*dig_enable) (struct wm97xx *, int enable);
+	void (*dig_restore) (struct wm97xx *);
+	void (*aux_prepare) (struct wm97xx *);
+};
+
+
+/* Machine specific and accelerated touch operations */
+struct wm97xx_mach_ops {
+
+	/* accelerated touch readback - coords are transmited on AC97 link */
+	int acc_enabled;
+	void (*acc_pen_up) (struct wm97xx *);
+	int (*acc_pen_down) (struct wm97xx *);
+	int (*acc_startup) (struct wm97xx *);
+	void (*acc_shutdown) (struct wm97xx *);
+
+	/* interrupt mask control - required for accelerated operation */
+	void (*irq_enable) (struct wm97xx *, int enable);
+
+	/* GPIO pin used for accelerated operation */
+	int irq_gpio;
+
+	/* pre and post sample - can be used to minimise any analog noise */
+	void (*pre_sample) (int);  /* function to run before sampling */
+	void (*post_sample) (int);  /* function to run after sampling */
+};
+
+struct wm97xx {
+	u16 dig[3], id, gpio[6], misc;	/* Cached codec registers */
+	u16 dig_save[3];		/* saved during aux reading */
+	struct wm97xx_codec_drv *codec;	/* attached codec driver*/
+	struct input_dev *input_dev;	/* touchscreen input device */
+	struct snd_ac97 *ac97;		/* ALSA codec access */
+	struct device *dev;		/* ALSA device */
+	struct platform_device *battery_dev;
+	struct platform_device *touch_dev;
+	struct wm97xx_mach_ops *mach_ops;
+	struct mutex codec_mutex;
+	struct delayed_work ts_reader;  /* Used to poll touchscreen */
+	unsigned long ts_reader_interval; /* Current interval for timer */
+	unsigned long ts_reader_min_interval; /* Minimum interval */
+	unsigned int pen_irq;		/* Pen IRQ number in use */
+	struct workqueue_struct *ts_workq;
+	struct work_struct pen_event_work;
+	u16 acc_slot;			/* AC97 slot used for acc touch data */
+	u16 acc_rate;			/* acc touch data rate */
+	unsigned pen_is_down:1;		/* Pen is down */
+	unsigned aux_waiting:1;		/* aux measurement waiting */
+	unsigned pen_probably_down:1;	/* used in polling mode */
+};
+
+/*
+ * Codec GPIO access (not supported on WM9705)
+ * This can be used to set/get codec GPIO and Virtual GPIO status.
+ */
+enum wm97xx_gpio_status wm97xx_get_gpio(struct wm97xx *wm, u32 gpio);
+void wm97xx_set_gpio(struct wm97xx *wm, u32 gpio,
+			  enum wm97xx_gpio_status status);
+void wm97xx_config_gpio(struct wm97xx *wm, u32 gpio,
+				     enum wm97xx_gpio_dir dir,
+				     enum wm97xx_gpio_pol pol,
+				     enum wm97xx_gpio_sticky sticky,
+				     enum wm97xx_gpio_wake wake);
+
+/* codec AC97 IO access */
+int wm97xx_reg_read(struct wm97xx *wm, u16 reg);
+void wm97xx_reg_write(struct wm97xx *wm, u16 reg, u16 val);
+
+/* aux adc readback */
+int wm97xx_read_aux_adc(struct wm97xx *wm, u16 adcsel);
+
+/* machine ops */
+int wm97xx_register_mach_ops(struct wm97xx *, struct wm97xx_mach_ops *);
+void wm97xx_unregister_mach_ops(struct wm97xx *);
+
+#endif