Merge branch 'sh-sci' into soc3-base
diff --git a/drivers/tty/serial/sh-sci.c b/drivers/tty/serial/sh-sci.c
index 7d8103c..e4bf0e4 100644
--- a/drivers/tty/serial/sh-sci.c
+++ b/drivers/tty/serial/sh-sci.c
@@ -23,35 +23,34 @@
#undef DEBUG
-#include <linux/module.h>
-#include <linux/errno.h>
-#include <linux/sh_dma.h>
-#include <linux/timer.h>
-#include <linux/interrupt.h>
-#include <linux/tty.h>
-#include <linux/tty_flip.h>
-#include <linux/serial.h>
-#include <linux/major.h>
-#include <linux/string.h>
-#include <linux/sysrq.h>
-#include <linux/ioport.h>
-#include <linux/mm.h>
-#include <linux/init.h>
-#include <linux/delay.h>
-#include <linux/console.h>
-#include <linux/platform_device.h>
-#include <linux/serial_sci.h>
-#include <linux/notifier.h>
-#include <linux/pm_runtime.h>
-#include <linux/cpufreq.h>
#include <linux/clk.h>
+#include <linux/console.h>
#include <linux/ctype.h>
-#include <linux/err.h>
+#include <linux/cpufreq.h>
+#include <linux/delay.h>
#include <linux/dmaengine.h>
#include <linux/dma-mapping.h>
+#include <linux/err.h>
+#include <linux/errno.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/ioport.h>
+#include <linux/major.h>
+#include <linux/module.h>
+#include <linux/mm.h>
+#include <linux/notifier.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
#include <linux/scatterlist.h>
+#include <linux/serial.h>
+#include <linux/serial_sci.h>
+#include <linux/sh_dma.h>
#include <linux/slab.h>
-#include <linux/gpio.h>
+#include <linux/string.h>
+#include <linux/sysrq.h>
+#include <linux/timer.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
#ifdef CONFIG_SUPERH
#include <asm/sh_bios.h>
@@ -64,6 +63,10 @@
/* Platform configuration */
struct plat_sci_port *cfg;
+ int overrun_bit;
+ unsigned int error_mask;
+ unsigned int sampling_rate;
+
/* Break timer */
struct timer_list break_timer;
@@ -74,8 +77,8 @@
/* Function clock */
struct clk *fclk;
+ int irqs[SCIx_NR_IRQS];
char *irqstr[SCIx_NR_IRQS];
- char *gpiostr[SCIx_NR_FNS];
struct dma_chan *chan_tx;
struct dma_chan *chan_rx;
@@ -421,9 +424,9 @@
pm_runtime_get_sync(sci_port->port.dev);
- clk_enable(sci_port->iclk);
+ clk_prepare_enable(sci_port->iclk);
sci_port->port.uartclk = clk_get_rate(sci_port->iclk);
- clk_enable(sci_port->fclk);
+ clk_prepare_enable(sci_port->fclk);
}
static void sci_port_disable(struct sci_port *sci_port)
@@ -431,8 +434,16 @@
if (!sci_port->port.dev)
return;
- clk_disable(sci_port->fclk);
- clk_disable(sci_port->iclk);
+ /* Cancel the break timer to ensure that the timer handler will not try
+ * to access the hardware with clocks and power disabled. Reset the
+ * break flag to make the break debouncing state machine ready for the
+ * next break.
+ */
+ del_timer_sync(&sci_port->break_timer);
+ sci_port->break_flag = 0;
+
+ clk_disable_unprepare(sci_port->fclk);
+ clk_disable_unprepare(sci_port->iclk);
pm_runtime_put_sync(sci_port->port.dev);
}
@@ -557,7 +568,7 @@
return 1;
/* Cast for ARM damage */
- return !!__raw_readb((void __iomem *)s->cfg->port_reg);
+ return !!__raw_readb((void __iomem *)(uintptr_t)s->cfg->port_reg);
}
/* ********************************************************************** *
@@ -733,8 +744,6 @@
{
struct sci_port *port = (struct sci_port *)data;
- sci_port_enable(port);
-
if (sci_rxd_in(&port->port) == 0) {
port->break_flag = 1;
sci_schedule_break_timer(port);
@@ -744,8 +753,6 @@
sci_schedule_break_timer(port);
} else
port->break_flag = 0;
-
- sci_port_disable(port);
}
static int sci_handle_errors(struct uart_port *port)
@@ -755,19 +762,15 @@
struct tty_port *tport = &port->state->port;
struct sci_port *s = to_sci_port(port);
- /*
- * Handle overruns, if supported.
- */
- if (s->cfg->overrun_bit != SCIx_NOT_SUPPORTED) {
- if (status & (1 << s->cfg->overrun_bit)) {
- port->icount.overrun++;
+ /* Handle overruns */
+ if (status & (1 << s->overrun_bit)) {
+ port->icount.overrun++;
- /* overrun error */
- if (tty_insert_flip_char(tport, 0, TTY_OVERRUN))
- copied++;
+ /* overrun error */
+ if (tty_insert_flip_char(tport, 0, TTY_OVERRUN))
+ copied++;
- dev_notice(port->dev, "overrun error");
- }
+ dev_notice(port->dev, "overrun error");
}
if (status & SCxSR_FER(port)) {
@@ -829,7 +832,7 @@
if (!reg->size)
return 0;
- if ((serial_port_in(port, SCLSR) & (1 << s->cfg->overrun_bit))) {
+ if ((serial_port_in(port, SCLSR) & (1 << s->overrun_bit))) {
serial_port_out(port, SCLSR, 0);
port->icount.overrun++;
@@ -1075,19 +1078,19 @@
for (i = j = 0; i < SCIx_NR_IRQS; i++, j++) {
struct sci_irq_desc *desc;
- unsigned int irq;
+ int irq;
if (SCIx_IRQ_IS_MUXED(port)) {
i = SCIx_MUX_IRQ;
irq = up->irq;
} else {
- irq = port->cfg->irqs[i];
+ irq = port->irqs[i];
/*
* Certain port types won't support all of the
* available interrupt sources.
*/
- if (unlikely(!irq))
+ if (unlikely(irq < 0))
continue;
}
@@ -1112,7 +1115,7 @@
out_noirq:
while (--i >= 0)
- free_irq(port->cfg->irqs[i], port);
+ free_irq(port->irqs[i], port);
out_nomem:
while (--j >= 0)
@@ -1130,16 +1133,16 @@
* IRQ first.
*/
for (i = 0; i < SCIx_NR_IRQS; i++) {
- unsigned int irq = port->cfg->irqs[i];
+ int irq = port->irqs[i];
/*
* Certain port types won't support all of the available
* interrupt sources.
*/
- if (unlikely(!irq))
+ if (unlikely(irq < 0))
continue;
- free_irq(port->cfg->irqs[i], port);
+ free_irq(port->irqs[i], port);
kfree(port->irqstr[i]);
if (SCIx_IRQ_IS_MUXED(port)) {
@@ -1149,67 +1152,6 @@
}
}
-static const char *sci_gpio_names[SCIx_NR_FNS] = {
- "sck", "rxd", "txd", "cts", "rts",
-};
-
-static const char *sci_gpio_str(unsigned int index)
-{
- return sci_gpio_names[index];
-}
-
-static void sci_init_gpios(struct sci_port *port)
-{
- struct uart_port *up = &port->port;
- int i;
-
- if (!port->cfg)
- return;
-
- for (i = 0; i < SCIx_NR_FNS; i++) {
- const char *desc;
- int ret;
-
- if (!port->cfg->gpios[i])
- continue;
-
- desc = sci_gpio_str(i);
-
- port->gpiostr[i] = kasprintf(GFP_KERNEL, "%s:%s",
- dev_name(up->dev), desc);
-
- /*
- * If we've failed the allocation, we can still continue
- * on with a NULL string.
- */
- if (!port->gpiostr[i])
- dev_notice(up->dev, "%s string allocation failure\n",
- desc);
-
- ret = gpio_request(port->cfg->gpios[i], port->gpiostr[i]);
- if (unlikely(ret != 0)) {
- dev_notice(up->dev, "failed %s gpio request\n", desc);
-
- /*
- * If we can't get the GPIO for whatever reason,
- * no point in keeping the verbose string around.
- */
- kfree(port->gpiostr[i]);
- }
- }
-}
-
-static void sci_free_gpios(struct sci_port *port)
-{
- int i;
-
- for (i = 0; i < SCIx_NR_FNS; i++)
- if (port->cfg->gpios[i]) {
- gpio_free(port->cfg->gpios[i]);
- kfree(port->gpiostr[i]);
- }
-}
-
static unsigned int sci_tx_empty(struct uart_port *port)
{
unsigned short status = serial_port_in(port, SCxSR);
@@ -1309,7 +1251,7 @@
}
if (room < count)
- dev_warn(port->dev, "Rx overrun: dropping %u bytes\n",
+ dev_warn(port->dev, "Rx overrun: dropping %zu bytes\n",
count - room);
if (!room)
return room;
@@ -1442,7 +1384,7 @@
int count;
chan->device->device_control(chan, DMA_TERMINATE_ALL, 0);
- dev_dbg(port->dev, "Read %u bytes with cookie %d\n",
+ dev_dbg(port->dev, "Read %zu bytes with cookie %d\n",
sh_desc->partial, sh_desc->cookie);
spin_lock_irqsave(&port->lock, flags);
@@ -1655,7 +1597,7 @@
if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) {
scr &= ~0x4000;
- enable_irq(s->cfg->irqs[1]);
+ enable_irq(s->irqs[SCIx_RXI_IRQ]);
}
serial_port_out(port, SCSCR, scr | SCSCR_RIE);
dev_dbg(port->dev, "DMA Rx timed out\n");
@@ -1691,16 +1633,17 @@
s->chan_tx = chan;
sg_init_table(&s->sg_tx, 1);
/* UART circular tx buffer is an aligned page. */
- BUG_ON((int)port->state->xmit.buf & ~PAGE_MASK);
+ BUG_ON((uintptr_t)port->state->xmit.buf & ~PAGE_MASK);
sg_set_page(&s->sg_tx, virt_to_page(port->state->xmit.buf),
- UART_XMIT_SIZE, (int)port->state->xmit.buf & ~PAGE_MASK);
+ UART_XMIT_SIZE,
+ (uintptr_t)port->state->xmit.buf & ~PAGE_MASK);
nent = dma_map_sg(port->dev, &s->sg_tx, 1, DMA_TO_DEVICE);
if (!nent)
sci_tx_dma_release(s, false);
else
- dev_dbg(port->dev, "%s: mapped %d@%p to %x\n", __func__,
- sg_dma_len(&s->sg_tx),
- port->state->xmit.buf, sg_dma_address(&s->sg_tx));
+ dev_dbg(port->dev, "%s: mapped %d@%p to %pad\n", __func__,
+ sg_dma_len(&s->sg_tx), port->state->xmit.buf,
+ &sg_dma_address(&s->sg_tx));
s->sg_len_tx = nent;
@@ -1740,7 +1683,7 @@
sg_init_table(sg, 1);
sg_set_page(sg, virt_to_page(buf[i]), s->buf_len_rx,
- (int)buf[i] & ~PAGE_MASK);
+ (uintptr_t)buf[i] & ~PAGE_MASK);
sg_dma_address(sg) = dma[i];
}
@@ -1808,20 +1751,21 @@
sci_free_irq(s);
}
-static unsigned int sci_scbrr_calc(unsigned int algo_id, unsigned int bps,
+static unsigned int sci_scbrr_calc(struct sci_port *s, unsigned int bps,
unsigned long freq)
{
- switch (algo_id) {
+ if (s->sampling_rate)
+ return DIV_ROUND_CLOSEST(freq, s->sampling_rate * bps) - 1;
+
+ switch (s->cfg->scbrr_algo_id) {
case SCBRR_ALGO_1:
- return ((freq + 16 * bps) / (16 * bps) - 1);
+ return freq / (16 * bps);
case SCBRR_ALGO_2:
- return ((freq + 16 * bps) / (32 * bps) - 1);
+ return DIV_ROUND_CLOSEST(freq, 32 * bps) - 1;
case SCBRR_ALGO_3:
- return (((freq * 2) + 16 * bps) / (16 * bps) - 1);
+ return freq / (8 * bps);
case SCBRR_ALGO_4:
- return (((freq * 2) + 16 * bps) / (32 * bps) - 1);
- case SCBRR_ALGO_5:
- return (((freq * 1000 / 32) / bps) - 1);
+ return DIV_ROUND_CLOSEST(freq, 16 * bps) - 1;
}
/* Warn, but use a safe default */
@@ -1903,12 +1847,11 @@
baud = uart_get_baud_rate(port, termios, old, 0, max_baud);
if (likely(baud && port->uartclk)) {
- if (s->cfg->scbrr_algo_id == SCBRR_ALGO_6) {
+ if (s->cfg->type == PORT_HSCIF) {
sci_baud_calc_hscif(baud, port->uartclk, &t, &srr,
&cks);
} else {
- t = sci_scbrr_calc(s->cfg->scbrr_algo_id, baud,
- port->uartclk);
+ t = sci_scbrr_calc(s, baud, port->uartclk);
for (cks = 0; t >= 256 && cks <= 3; cks++)
t >>= 2;
}
@@ -2115,10 +2058,6 @@
static int sci_verify_port(struct uart_port *port, struct serial_struct *ser)
{
- struct sci_port *s = to_sci_port(port);
-
- if (ser->irq != s->cfg->irqs[SCIx_TXI_IRQ] || ser->irq > nr_irqs)
- return -EINVAL;
if (ser->baud_base < 2400)
/* No paper tape reader for Mitch.. */
return -EINVAL;
@@ -2151,11 +2090,13 @@
};
static int sci_init_single(struct platform_device *dev,
- struct sci_port *sci_port,
- unsigned int index,
- struct plat_sci_port *p)
+ struct sci_port *sci_port, unsigned int index,
+ struct plat_sci_port *p, bool early)
{
struct uart_port *port = &sci_port->port;
+ const struct resource *res;
+ unsigned int sampling_rate;
+ unsigned int i;
int ret;
sci_port->cfg = p;
@@ -2164,22 +2105,36 @@
port->iotype = UPIO_MEM;
port->line = index;
- switch (p->type) {
- case PORT_SCIFB:
- port->fifosize = 256;
- break;
- case PORT_HSCIF:
- port->fifosize = 128;
- break;
- case PORT_SCIFA:
- port->fifosize = 64;
- break;
- case PORT_SCIF:
- port->fifosize = 16;
- break;
- default:
- port->fifosize = 1;
- break;
+ if (dev->num_resources) {
+ /* Device has resources, use them. */
+ res = platform_get_resource(dev, IORESOURCE_MEM, 0);
+ if (res == NULL)
+ return -ENOMEM;
+
+ port->mapbase = res->start;
+
+ for (i = 0; i < ARRAY_SIZE(sci_port->irqs); ++i)
+ sci_port->irqs[i] = platform_get_irq(dev, i);
+
+ /* The SCI generates several interrupts. They can be muxed
+ * together or connected to different interrupt lines. In the
+ * muxed case only one interrupt resource is specified. In the
+ * non-muxed case three or four interrupt resources are
+ * specified, as the BRI interrupt is optional.
+ */
+ if (sci_port->irqs[0] < 0)
+ return -ENXIO;
+
+ if (sci_port->irqs[1] < 0) {
+ sci_port->irqs[1] = sci_port->irqs[0];
+ sci_port->irqs[2] = sci_port->irqs[0];
+ sci_port->irqs[3] = sci_port->irqs[0];
+ }
+ } else {
+ /* No resources, use old-style platform data. */
+ port->mapbase = p->mapbase;
+ for (i = 0; i < ARRAY_SIZE(sci_port->irqs); ++i)
+ sci_port->irqs[i] = p->irqs[i] ? p->irqs[i] : -ENXIO;
}
if (p->regtype == SCIx_PROBE_REGTYPE) {
@@ -2188,7 +2143,52 @@
return ret;
}
- if (dev) {
+ switch (p->type) {
+ case PORT_SCIFB:
+ port->fifosize = 256;
+ sci_port->overrun_bit = 9;
+ sampling_rate = 16;
+ break;
+ case PORT_HSCIF:
+ port->fifosize = 128;
+ sampling_rate = 0;
+ sci_port->overrun_bit = 0;
+ break;
+ case PORT_SCIFA:
+ port->fifosize = 64;
+ sci_port->overrun_bit = 9;
+ sampling_rate = 16;
+ break;
+ case PORT_SCIF:
+ port->fifosize = 16;
+ if (p->regtype == SCIx_SH7705_SCIF_REGTYPE) {
+ sci_port->overrun_bit = 9;
+ sampling_rate = 16;
+ } else {
+ sci_port->overrun_bit = 0;
+ sampling_rate = 32;
+ }
+ break;
+ default:
+ port->fifosize = 1;
+ sci_port->overrun_bit = 5;
+ sampling_rate = 32;
+ break;
+ }
+
+ /* Set the sampling rate if the baud rate calculation algorithm isn't
+ * specified.
+ */
+ if (p->scbrr_algo_id == SCBRR_ALGO_NONE) {
+ /* SCIFA on sh7723 and sh7724 need a custom sampling rate that
+ * doesn't match the SoC datasheet, this should be investigated.
+ * Let platform data override the sampling rate for now.
+ */
+ sci_port->sampling_rate = p->sampling_rate ? p->sampling_rate
+ : sampling_rate;
+ }
+
+ if (!early) {
sci_port->iclk = clk_get(&dev->dev, "sci_ick");
if (IS_ERR(sci_port->iclk)) {
sci_port->iclk = clk_get(&dev->dev, "peripheral_clk");
@@ -2208,8 +2208,6 @@
port->dev = &dev->dev;
- sci_init_gpios(sci_port);
-
pm_runtime_enable(&dev->dev);
}
@@ -2220,32 +2218,22 @@
/*
* Establish some sensible defaults for the error detection.
*/
- if (!p->error_mask)
- p->error_mask = (p->type == PORT_SCI) ?
+ sci_port->error_mask = (p->type == PORT_SCI) ?
SCI_DEFAULT_ERROR_MASK : SCIF_DEFAULT_ERROR_MASK;
/*
* Establish sensible defaults for the overrun detection, unless
* the part has explicitly disabled support for it.
*/
- if (p->overrun_bit != SCIx_NOT_SUPPORTED) {
- if (p->type == PORT_SCI)
- p->overrun_bit = 5;
- else if (p->scbrr_algo_id == SCBRR_ALGO_4)
- p->overrun_bit = 9;
- else
- p->overrun_bit = 0;
- /*
- * Make the error mask inclusive of overrun detection, if
- * supported.
- */
- p->error_mask |= (1 << p->overrun_bit);
- }
+ /*
+ * Make the error mask inclusive of overrun detection, if
+ * supported.
+ */
+ sci_port->error_mask |= 1 << sci_port->overrun_bit;
- port->mapbase = p->mapbase;
port->type = p->type;
- port->flags = p->flags;
+ port->flags = UPF_FIXED_PORT | p->flags;
port->regshift = p->regshift;
/*
@@ -2255,7 +2243,7 @@
*
* For the muxed case there's nothing more to do.
*/
- port->irq = p->irqs[SCIx_RXI_IRQ];
+ port->irq = sci_port->irqs[SCIx_RXI_IRQ];
port->irqflags = 0;
port->serial_in = sci_serial_in;
@@ -2270,8 +2258,6 @@
static void sci_cleanup_single(struct sci_port *port)
{
- sci_free_gpios(port);
-
clk_put(port->iclk);
clk_put(port->fclk);
@@ -2387,7 +2373,7 @@
early_serial_console.index = pdev->id;
- sci_init_single(NULL, &sci_ports[pdev->id], pdev->id, cfg);
+ sci_init_single(pdev, &sci_ports[pdev->id], pdev->id, cfg, true);
serial_console_setup(&early_serial_console, early_serial_buf);
@@ -2454,7 +2440,7 @@
return -EINVAL;
}
- ret = sci_init_single(dev, sciport, index, p);
+ ret = sci_init_single(dev, sciport, index, p, false);
if (ret)
return ret;
diff --git a/drivers/tty/serial/sh-sci.h b/drivers/tty/serial/sh-sci.h
index 5aca736..d5db81a 100644
--- a/drivers/tty/serial/sh-sci.h
+++ b/drivers/tty/serial/sh-sci.h
@@ -9,7 +9,7 @@
#define SCxSR_PER(port) (((port)->type == PORT_SCI) ? SCI_PER : SCIF_PER)
#define SCxSR_BRK(port) (((port)->type == PORT_SCI) ? 0x00 : SCIF_BRK)
-#define SCxSR_ERRORS(port) (to_sci_port(port)->cfg->error_mask)
+#define SCxSR_ERRORS(port) (to_sci_port(port)->error_mask)
#if defined(CONFIG_CPU_SUBTYPE_SH7705) || \
defined(CONFIG_CPU_SUBTYPE_SH7720) || \
diff --git a/include/linux/serial_sci.h b/include/linux/serial_sci.h
index 50fe651..af414e1 100644
--- a/include/linux/serial_sci.h
+++ b/include/linux/serial_sci.h
@@ -11,11 +11,11 @@
#define SCIx_NOT_SUPPORTED (-1)
enum {
- SCBRR_ALGO_1, /* ((clk + 16 * bps) / (16 * bps) - 1) */
- SCBRR_ALGO_2, /* ((clk + 16 * bps) / (32 * bps) - 1) */
- SCBRR_ALGO_3, /* (((clk * 2) + 16 * bps) / (16 * bps) - 1) */
- SCBRR_ALGO_4, /* (((clk * 2) + 16 * bps) / (32 * bps) - 1) */
- SCBRR_ALGO_5, /* (((clk * 1000 / 32) / bps) - 1) */
+ SCBRR_ALGO_NONE, /* Compute sampling rate in the driver */
+ SCBRR_ALGO_1, /* clk / (16 * bps) */
+ SCBRR_ALGO_2, /* DIV_ROUND_CLOSEST(clk, 32 * bps) - 1 */
+ SCBRR_ALGO_3, /* clk / (8 * bps) */
+ SCBRR_ALGO_4, /* DIV_ROUND_CLOSEST(clk, 16 * bps) - 1 */
SCBRR_ALGO_6, /* HSCIF variable sample rate algorithm */
};
@@ -70,17 +70,6 @@
SCIx_MUX_IRQ = SCIx_NR_IRQS, /* special case */
};
-/* Offsets into the sci_port->gpios array */
-enum {
- SCIx_SCK,
- SCIx_RXD,
- SCIx_TXD,
- SCIx_CTS,
- SCIx_RTS,
-
- SCIx_NR_FNS,
-};
-
enum {
SCIx_PROBE_REGTYPE,
@@ -108,10 +97,10 @@
}
#define SCIx_IRQ_IS_MUXED(port) \
- ((port)->cfg->irqs[SCIx_ERI_IRQ] == \
- (port)->cfg->irqs[SCIx_RXI_IRQ]) || \
- ((port)->cfg->irqs[SCIx_ERI_IRQ] && \
- !(port)->cfg->irqs[SCIx_RXI_IRQ])
+ ((port)->irqs[SCIx_ERI_IRQ] == \
+ (port)->irqs[SCIx_RXI_IRQ]) || \
+ ((port)->irqs[SCIx_ERI_IRQ] && \
+ ((port)->irqs[SCIx_RXI_IRQ] < 0))
/*
* SCI register subset common for all port types.
* Not all registers will exist on all parts.
@@ -142,20 +131,17 @@
struct plat_sci_port {
unsigned long mapbase; /* resource base */
unsigned int irqs[SCIx_NR_IRQS]; /* ERI, RXI, TXI, BRI */
- unsigned int gpios[SCIx_NR_FNS]; /* SCK, RXD, TXD, CTS, RTS */
unsigned int type; /* SCI / SCIF / IRDA / HSCIF */
upf_t flags; /* UPF_* flags */
unsigned long capabilities; /* Port features/capabilities */
+ unsigned int sampling_rate;
unsigned int scbrr_algo_id; /* SCBRR calculation algo */
unsigned int scscr; /* SCSCR initialization */
/*
* Platform overrides if necessary, defaults otherwise.
*/
- int overrun_bit;
- unsigned int error_mask;
-
int port_reg;
unsigned char regshift;
unsigned char regtype;