| /* |
| * TPO TD043MTEA1 Panel driver |
| * |
| * Author: Gražvydas Ignotas <notasas@gmail.com> |
| * Converted to new DSS device model: Tomi Valkeinen <tomi.valkeinen@ti.com> |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation; either version 2 of the License, or |
| * (at your option) any later version. |
| */ |
| |
| #include <linux/module.h> |
| #include <linux/delay.h> |
| #include <linux/spi/spi.h> |
| #include <linux/regulator/consumer.h> |
| #include <linux/gpio.h> |
| #include <linux/err.h> |
| #include <linux/slab.h> |
| #include <linux/of_gpio.h> |
| |
| #include <video/omapdss.h> |
| #include <video/omap-panel-data.h> |
| |
| #define TPO_R02_MODE(x) ((x) & 7) |
| #define TPO_R02_MODE_800x480 7 |
| #define TPO_R02_NCLK_RISING BIT(3) |
| #define TPO_R02_HSYNC_HIGH BIT(4) |
| #define TPO_R02_VSYNC_HIGH BIT(5) |
| |
| #define TPO_R03_NSTANDBY BIT(0) |
| #define TPO_R03_EN_CP_CLK BIT(1) |
| #define TPO_R03_EN_VGL_PUMP BIT(2) |
| #define TPO_R03_EN_PWM BIT(3) |
| #define TPO_R03_DRIVING_CAP_100 BIT(4) |
| #define TPO_R03_EN_PRE_CHARGE BIT(6) |
| #define TPO_R03_SOFTWARE_CTL BIT(7) |
| |
| #define TPO_R04_NFLIP_H BIT(0) |
| #define TPO_R04_NFLIP_V BIT(1) |
| #define TPO_R04_CP_CLK_FREQ_1H BIT(2) |
| #define TPO_R04_VGL_FREQ_1H BIT(4) |
| |
| #define TPO_R03_VAL_NORMAL (TPO_R03_NSTANDBY | TPO_R03_EN_CP_CLK | \ |
| TPO_R03_EN_VGL_PUMP | TPO_R03_EN_PWM | \ |
| TPO_R03_DRIVING_CAP_100 | TPO_R03_EN_PRE_CHARGE | \ |
| TPO_R03_SOFTWARE_CTL) |
| |
| #define TPO_R03_VAL_STANDBY (TPO_R03_DRIVING_CAP_100 | \ |
| TPO_R03_EN_PRE_CHARGE | TPO_R03_SOFTWARE_CTL) |
| |
| static const u16 tpo_td043_def_gamma[12] = { |
| 105, 315, 381, 431, 490, 537, 579, 686, 780, 837, 880, 1023 |
| }; |
| |
| struct panel_drv_data { |
| struct omap_dss_device dssdev; |
| struct omap_dss_device *in; |
| |
| struct omap_video_timings videomode; |
| |
| int data_lines; |
| |
| struct spi_device *spi; |
| struct regulator *vcc_reg; |
| int nreset_gpio; |
| u16 gamma[12]; |
| u32 mode; |
| u32 hmirror:1; |
| u32 vmirror:1; |
| u32 powered_on:1; |
| u32 spi_suspended:1; |
| u32 power_on_resume:1; |
| }; |
| |
| static const struct omap_video_timings tpo_td043_timings = { |
| .x_res = 800, |
| .y_res = 480, |
| |
| .pixelclock = 36000000, |
| |
| .hsw = 1, |
| .hfp = 68, |
| .hbp = 214, |
| |
| .vsw = 1, |
| .vfp = 39, |
| .vbp = 34, |
| |
| .vsync_level = OMAPDSS_SIG_ACTIVE_LOW, |
| .hsync_level = OMAPDSS_SIG_ACTIVE_LOW, |
| .data_pclk_edge = OMAPDSS_DRIVE_SIG_FALLING_EDGE, |
| .de_level = OMAPDSS_SIG_ACTIVE_HIGH, |
| .sync_pclk_edge = OMAPDSS_DRIVE_SIG_OPPOSITE_EDGES, |
| }; |
| |
| #define to_panel_data(p) container_of(p, struct panel_drv_data, dssdev) |
| |
| static int tpo_td043_write(struct spi_device *spi, u8 addr, u8 data) |
| { |
| struct spi_message m; |
| struct spi_transfer xfer; |
| u16 w; |
| int r; |
| |
| spi_message_init(&m); |
| |
| memset(&xfer, 0, sizeof(xfer)); |
| |
| w = ((u16)addr << 10) | (1 << 8) | data; |
| xfer.tx_buf = &w; |
| xfer.bits_per_word = 16; |
| xfer.len = 2; |
| spi_message_add_tail(&xfer, &m); |
| |
| r = spi_sync(spi, &m); |
| if (r < 0) |
| dev_warn(&spi->dev, "failed to write to LCD reg (%d)\n", r); |
| return r; |
| } |
| |
| static void tpo_td043_write_gamma(struct spi_device *spi, u16 gamma[12]) |
| { |
| u8 i, val; |
| |
| /* gamma bits [9:8] */ |
| for (val = i = 0; i < 4; i++) |
| val |= (gamma[i] & 0x300) >> ((i + 1) * 2); |
| tpo_td043_write(spi, 0x11, val); |
| |
| for (val = i = 0; i < 4; i++) |
| val |= (gamma[i+4] & 0x300) >> ((i + 1) * 2); |
| tpo_td043_write(spi, 0x12, val); |
| |
| for (val = i = 0; i < 4; i++) |
| val |= (gamma[i+8] & 0x300) >> ((i + 1) * 2); |
| tpo_td043_write(spi, 0x13, val); |
| |
| /* gamma bits [7:0] */ |
| for (val = i = 0; i < 12; i++) |
| tpo_td043_write(spi, 0x14 + i, gamma[i] & 0xff); |
| } |
| |
| static int tpo_td043_write_mirror(struct spi_device *spi, bool h, bool v) |
| { |
| u8 reg4 = TPO_R04_NFLIP_H | TPO_R04_NFLIP_V | |
| TPO_R04_CP_CLK_FREQ_1H | TPO_R04_VGL_FREQ_1H; |
| if (h) |
| reg4 &= ~TPO_R04_NFLIP_H; |
| if (v) |
| reg4 &= ~TPO_R04_NFLIP_V; |
| |
| return tpo_td043_write(spi, 4, reg4); |
| } |
| |
| static int tpo_td043_set_hmirror(struct omap_dss_device *dssdev, bool enable) |
| { |
| struct panel_drv_data *ddata = dev_get_drvdata(dssdev->dev); |
| |
| ddata->hmirror = enable; |
| return tpo_td043_write_mirror(ddata->spi, ddata->hmirror, |
| ddata->vmirror); |
| } |
| |
| static bool tpo_td043_get_hmirror(struct omap_dss_device *dssdev) |
| { |
| struct panel_drv_data *ddata = dev_get_drvdata(dssdev->dev); |
| |
| return ddata->hmirror; |
| } |
| |
| static ssize_t tpo_td043_vmirror_show(struct device *dev, |
| struct device_attribute *attr, char *buf) |
| { |
| struct panel_drv_data *ddata = dev_get_drvdata(dev); |
| |
| return snprintf(buf, PAGE_SIZE, "%d\n", ddata->vmirror); |
| } |
| |
| static ssize_t tpo_td043_vmirror_store(struct device *dev, |
| struct device_attribute *attr, const char *buf, size_t count) |
| { |
| struct panel_drv_data *ddata = dev_get_drvdata(dev); |
| int val; |
| int ret; |
| |
| ret = kstrtoint(buf, 0, &val); |
| if (ret < 0) |
| return ret; |
| |
| val = !!val; |
| |
| ret = tpo_td043_write_mirror(ddata->spi, ddata->hmirror, val); |
| if (ret < 0) |
| return ret; |
| |
| ddata->vmirror = val; |
| |
| return count; |
| } |
| |
| static ssize_t tpo_td043_mode_show(struct device *dev, |
| struct device_attribute *attr, char *buf) |
| { |
| struct panel_drv_data *ddata = dev_get_drvdata(dev); |
| |
| return snprintf(buf, PAGE_SIZE, "%d\n", ddata->mode); |
| } |
| |
| static ssize_t tpo_td043_mode_store(struct device *dev, |
| struct device_attribute *attr, const char *buf, size_t count) |
| { |
| struct panel_drv_data *ddata = dev_get_drvdata(dev); |
| long val; |
| int ret; |
| |
| ret = kstrtol(buf, 0, &val); |
| if (ret != 0 || val & ~7) |
| return -EINVAL; |
| |
| ddata->mode = val; |
| |
| val |= TPO_R02_NCLK_RISING; |
| tpo_td043_write(ddata->spi, 2, val); |
| |
| return count; |
| } |
| |
| static ssize_t tpo_td043_gamma_show(struct device *dev, |
| struct device_attribute *attr, char *buf) |
| { |
| struct panel_drv_data *ddata = dev_get_drvdata(dev); |
| ssize_t len = 0; |
| int ret; |
| int i; |
| |
| for (i = 0; i < ARRAY_SIZE(ddata->gamma); i++) { |
| ret = snprintf(buf + len, PAGE_SIZE - len, "%u ", |
| ddata->gamma[i]); |
| if (ret < 0) |
| return ret; |
| len += ret; |
| } |
| buf[len - 1] = '\n'; |
| |
| return len; |
| } |
| |
| static ssize_t tpo_td043_gamma_store(struct device *dev, |
| struct device_attribute *attr, const char *buf, size_t count) |
| { |
| struct panel_drv_data *ddata = dev_get_drvdata(dev); |
| unsigned int g[12]; |
| int ret; |
| int i; |
| |
| ret = sscanf(buf, "%u %u %u %u %u %u %u %u %u %u %u %u", |
| &g[0], &g[1], &g[2], &g[3], &g[4], &g[5], |
| &g[6], &g[7], &g[8], &g[9], &g[10], &g[11]); |
| |
| if (ret != 12) |
| return -EINVAL; |
| |
| for (i = 0; i < 12; i++) |
| ddata->gamma[i] = g[i]; |
| |
| tpo_td043_write_gamma(ddata->spi, ddata->gamma); |
| |
| return count; |
| } |
| |
| static DEVICE_ATTR(vmirror, S_IRUGO | S_IWUSR, |
| tpo_td043_vmirror_show, tpo_td043_vmirror_store); |
| static DEVICE_ATTR(mode, S_IRUGO | S_IWUSR, |
| tpo_td043_mode_show, tpo_td043_mode_store); |
| static DEVICE_ATTR(gamma, S_IRUGO | S_IWUSR, |
| tpo_td043_gamma_show, tpo_td043_gamma_store); |
| |
| static struct attribute *tpo_td043_attrs[] = { |
| &dev_attr_vmirror.attr, |
| &dev_attr_mode.attr, |
| &dev_attr_gamma.attr, |
| NULL, |
| }; |
| |
| static struct attribute_group tpo_td043_attr_group = { |
| .attrs = tpo_td043_attrs, |
| }; |
| |
| static int tpo_td043_power_on(struct panel_drv_data *ddata) |
| { |
| int r; |
| |
| if (ddata->powered_on) |
| return 0; |
| |
| r = regulator_enable(ddata->vcc_reg); |
| if (r != 0) |
| return r; |
| |
| /* wait for panel to stabilize */ |
| msleep(160); |
| |
| if (gpio_is_valid(ddata->nreset_gpio)) |
| gpio_set_value(ddata->nreset_gpio, 1); |
| |
| tpo_td043_write(ddata->spi, 2, |
| TPO_R02_MODE(ddata->mode) | TPO_R02_NCLK_RISING); |
| tpo_td043_write(ddata->spi, 3, TPO_R03_VAL_NORMAL); |
| tpo_td043_write(ddata->spi, 0x20, 0xf0); |
| tpo_td043_write(ddata->spi, 0x21, 0xf0); |
| tpo_td043_write_mirror(ddata->spi, ddata->hmirror, |
| ddata->vmirror); |
| tpo_td043_write_gamma(ddata->spi, ddata->gamma); |
| |
| ddata->powered_on = 1; |
| return 0; |
| } |
| |
| static void tpo_td043_power_off(struct panel_drv_data *ddata) |
| { |
| if (!ddata->powered_on) |
| return; |
| |
| tpo_td043_write(ddata->spi, 3, |
| TPO_R03_VAL_STANDBY | TPO_R03_EN_PWM); |
| |
| if (gpio_is_valid(ddata->nreset_gpio)) |
| gpio_set_value(ddata->nreset_gpio, 0); |
| |
| /* wait for at least 2 vsyncs before cutting off power */ |
| msleep(50); |
| |
| tpo_td043_write(ddata->spi, 3, TPO_R03_VAL_STANDBY); |
| |
| regulator_disable(ddata->vcc_reg); |
| |
| ddata->powered_on = 0; |
| } |
| |
| static int tpo_td043_connect(struct omap_dss_device *dssdev) |
| { |
| struct panel_drv_data *ddata = to_panel_data(dssdev); |
| struct omap_dss_device *in = ddata->in; |
| int r; |
| |
| if (omapdss_device_is_connected(dssdev)) |
| return 0; |
| |
| r = in->ops.dpi->connect(in, dssdev); |
| if (r) |
| return r; |
| |
| return 0; |
| } |
| |
| static void tpo_td043_disconnect(struct omap_dss_device *dssdev) |
| { |
| struct panel_drv_data *ddata = to_panel_data(dssdev); |
| struct omap_dss_device *in = ddata->in; |
| |
| if (!omapdss_device_is_connected(dssdev)) |
| return; |
| |
| in->ops.dpi->disconnect(in, dssdev); |
| } |
| |
| static int tpo_td043_enable(struct omap_dss_device *dssdev) |
| { |
| struct panel_drv_data *ddata = to_panel_data(dssdev); |
| struct omap_dss_device *in = ddata->in; |
| int r; |
| |
| if (!omapdss_device_is_connected(dssdev)) |
| return -ENODEV; |
| |
| if (omapdss_device_is_enabled(dssdev)) |
| return 0; |
| |
| if (ddata->data_lines) |
| in->ops.dpi->set_data_lines(in, ddata->data_lines); |
| in->ops.dpi->set_timings(in, &ddata->videomode); |
| |
| r = in->ops.dpi->enable(in); |
| if (r) |
| return r; |
| |
| /* |
| * If we are resuming from system suspend, SPI clocks might not be |
| * enabled yet, so we'll program the LCD from SPI PM resume callback. |
| */ |
| if (!ddata->spi_suspended) { |
| r = tpo_td043_power_on(ddata); |
| if (r) { |
| in->ops.dpi->disable(in); |
| return r; |
| } |
| } |
| |
| dssdev->state = OMAP_DSS_DISPLAY_ACTIVE; |
| |
| return 0; |
| } |
| |
| static void tpo_td043_disable(struct omap_dss_device *dssdev) |
| { |
| struct panel_drv_data *ddata = to_panel_data(dssdev); |
| struct omap_dss_device *in = ddata->in; |
| |
| if (!omapdss_device_is_enabled(dssdev)) |
| return; |
| |
| in->ops.dpi->disable(in); |
| |
| if (!ddata->spi_suspended) |
| tpo_td043_power_off(ddata); |
| |
| dssdev->state = OMAP_DSS_DISPLAY_DISABLED; |
| } |
| |
| static void tpo_td043_set_timings(struct omap_dss_device *dssdev, |
| struct omap_video_timings *timings) |
| { |
| struct panel_drv_data *ddata = to_panel_data(dssdev); |
| struct omap_dss_device *in = ddata->in; |
| |
| ddata->videomode = *timings; |
| dssdev->panel.timings = *timings; |
| |
| in->ops.dpi->set_timings(in, timings); |
| } |
| |
| static void tpo_td043_get_timings(struct omap_dss_device *dssdev, |
| struct omap_video_timings *timings) |
| { |
| struct panel_drv_data *ddata = to_panel_data(dssdev); |
| |
| *timings = ddata->videomode; |
| } |
| |
| static int tpo_td043_check_timings(struct omap_dss_device *dssdev, |
| struct omap_video_timings *timings) |
| { |
| struct panel_drv_data *ddata = to_panel_data(dssdev); |
| struct omap_dss_device *in = ddata->in; |
| |
| return in->ops.dpi->check_timings(in, timings); |
| } |
| |
| static struct omap_dss_driver tpo_td043_ops = { |
| .connect = tpo_td043_connect, |
| .disconnect = tpo_td043_disconnect, |
| |
| .enable = tpo_td043_enable, |
| .disable = tpo_td043_disable, |
| |
| .set_timings = tpo_td043_set_timings, |
| .get_timings = tpo_td043_get_timings, |
| .check_timings = tpo_td043_check_timings, |
| |
| .set_mirror = tpo_td043_set_hmirror, |
| .get_mirror = tpo_td043_get_hmirror, |
| |
| .get_resolution = omapdss_default_get_resolution, |
| }; |
| |
| |
| static int tpo_td043_probe_pdata(struct spi_device *spi) |
| { |
| const struct panel_tpo_td043mtea1_platform_data *pdata; |
| struct panel_drv_data *ddata = dev_get_drvdata(&spi->dev); |
| struct omap_dss_device *dssdev, *in; |
| |
| pdata = dev_get_platdata(&spi->dev); |
| |
| ddata->nreset_gpio = pdata->nreset_gpio; |
| |
| in = omap_dss_find_output(pdata->source); |
| if (in == NULL) { |
| dev_err(&spi->dev, "failed to find video source '%s'\n", |
| pdata->source); |
| return -EPROBE_DEFER; |
| } |
| ddata->in = in; |
| |
| ddata->data_lines = pdata->data_lines; |
| |
| dssdev = &ddata->dssdev; |
| dssdev->name = pdata->name; |
| |
| return 0; |
| } |
| |
| static int tpo_td043_probe_of(struct spi_device *spi) |
| { |
| struct device_node *node = spi->dev.of_node; |
| struct panel_drv_data *ddata = dev_get_drvdata(&spi->dev); |
| struct omap_dss_device *in; |
| int gpio; |
| |
| gpio = of_get_named_gpio(node, "reset-gpios", 0); |
| if (!gpio_is_valid(gpio)) { |
| dev_err(&spi->dev, "failed to parse enable gpio\n"); |
| return gpio; |
| } |
| ddata->nreset_gpio = gpio; |
| |
| in = omapdss_of_find_source_for_first_ep(node); |
| if (IS_ERR(in)) { |
| dev_err(&spi->dev, "failed to find video source\n"); |
| return PTR_ERR(in); |
| } |
| |
| ddata->in = in; |
| |
| return 0; |
| } |
| |
| static int tpo_td043_probe(struct spi_device *spi) |
| { |
| struct panel_drv_data *ddata; |
| struct omap_dss_device *dssdev; |
| int r; |
| |
| dev_dbg(&spi->dev, "%s\n", __func__); |
| |
| spi->bits_per_word = 16; |
| spi->mode = SPI_MODE_0; |
| |
| r = spi_setup(spi); |
| if (r < 0) { |
| dev_err(&spi->dev, "spi_setup failed: %d\n", r); |
| return r; |
| } |
| |
| ddata = devm_kzalloc(&spi->dev, sizeof(*ddata), GFP_KERNEL); |
| if (ddata == NULL) |
| return -ENOMEM; |
| |
| dev_set_drvdata(&spi->dev, ddata); |
| |
| ddata->spi = spi; |
| |
| if (dev_get_platdata(&spi->dev)) { |
| r = tpo_td043_probe_pdata(spi); |
| if (r) |
| return r; |
| } else if (spi->dev.of_node) { |
| r = tpo_td043_probe_of(spi); |
| if (r) |
| return r; |
| } else { |
| return -ENODEV; |
| } |
| |
| ddata->mode = TPO_R02_MODE_800x480; |
| memcpy(ddata->gamma, tpo_td043_def_gamma, sizeof(ddata->gamma)); |
| |
| ddata->vcc_reg = devm_regulator_get(&spi->dev, "vcc"); |
| if (IS_ERR(ddata->vcc_reg)) { |
| dev_err(&spi->dev, "failed to get LCD VCC regulator\n"); |
| r = PTR_ERR(ddata->vcc_reg); |
| goto err_regulator; |
| } |
| |
| if (gpio_is_valid(ddata->nreset_gpio)) { |
| r = devm_gpio_request_one(&spi->dev, |
| ddata->nreset_gpio, GPIOF_OUT_INIT_LOW, |
| "lcd reset"); |
| if (r < 0) { |
| dev_err(&spi->dev, "couldn't request reset GPIO\n"); |
| goto err_gpio_req; |
| } |
| } |
| |
| r = sysfs_create_group(&spi->dev.kobj, &tpo_td043_attr_group); |
| if (r) { |
| dev_err(&spi->dev, "failed to create sysfs files\n"); |
| goto err_sysfs; |
| } |
| |
| ddata->videomode = tpo_td043_timings; |
| |
| dssdev = &ddata->dssdev; |
| dssdev->dev = &spi->dev; |
| dssdev->driver = &tpo_td043_ops; |
| dssdev->type = OMAP_DISPLAY_TYPE_DPI; |
| dssdev->owner = THIS_MODULE; |
| dssdev->panel.timings = ddata->videomode; |
| |
| r = omapdss_register_display(dssdev); |
| if (r) { |
| dev_err(&spi->dev, "Failed to register panel\n"); |
| goto err_reg; |
| } |
| |
| return 0; |
| |
| err_reg: |
| sysfs_remove_group(&spi->dev.kobj, &tpo_td043_attr_group); |
| err_sysfs: |
| err_gpio_req: |
| err_regulator: |
| omap_dss_put_device(ddata->in); |
| return r; |
| } |
| |
| static int tpo_td043_remove(struct spi_device *spi) |
| { |
| struct panel_drv_data *ddata = dev_get_drvdata(&spi->dev); |
| struct omap_dss_device *dssdev = &ddata->dssdev; |
| struct omap_dss_device *in = ddata->in; |
| |
| dev_dbg(&ddata->spi->dev, "%s\n", __func__); |
| |
| omapdss_unregister_display(dssdev); |
| |
| tpo_td043_disable(dssdev); |
| tpo_td043_disconnect(dssdev); |
| |
| omap_dss_put_device(in); |
| |
| sysfs_remove_group(&spi->dev.kobj, &tpo_td043_attr_group); |
| |
| return 0; |
| } |
| |
| #ifdef CONFIG_PM_SLEEP |
| static int tpo_td043_spi_suspend(struct device *dev) |
| { |
| struct panel_drv_data *ddata = dev_get_drvdata(dev); |
| |
| dev_dbg(dev, "tpo_td043_spi_suspend, tpo %p\n", ddata); |
| |
| ddata->power_on_resume = ddata->powered_on; |
| tpo_td043_power_off(ddata); |
| ddata->spi_suspended = 1; |
| |
| return 0; |
| } |
| |
| static int tpo_td043_spi_resume(struct device *dev) |
| { |
| struct panel_drv_data *ddata = dev_get_drvdata(dev); |
| int ret; |
| |
| dev_dbg(dev, "tpo_td043_spi_resume\n"); |
| |
| if (ddata->power_on_resume) { |
| ret = tpo_td043_power_on(ddata); |
| if (ret) |
| return ret; |
| } |
| ddata->spi_suspended = 0; |
| |
| return 0; |
| } |
| #endif |
| |
| static SIMPLE_DEV_PM_OPS(tpo_td043_spi_pm, |
| tpo_td043_spi_suspend, tpo_td043_spi_resume); |
| |
| static const struct of_device_id tpo_td043_of_match[] = { |
| { .compatible = "omapdss,tpo,td043mtea1", }, |
| {}, |
| }; |
| |
| MODULE_DEVICE_TABLE(of, tpo_td043_of_match); |
| |
| static struct spi_driver tpo_td043_spi_driver = { |
| .driver = { |
| .name = "panel-tpo-td043mtea1", |
| .owner = THIS_MODULE, |
| .pm = &tpo_td043_spi_pm, |
| .of_match_table = tpo_td043_of_match, |
| .suppress_bind_attrs = true, |
| }, |
| .probe = tpo_td043_probe, |
| .remove = tpo_td043_remove, |
| }; |
| |
| module_spi_driver(tpo_td043_spi_driver); |
| |
| MODULE_ALIAS("spi:tpo,td043mtea1"); |
| MODULE_AUTHOR("Gražvydas Ignotas <notasas@gmail.com>"); |
| MODULE_DESCRIPTION("TPO TD043MTEA1 LCD Driver"); |
| MODULE_LICENSE("GPL"); |