| /* |
| * Copyright (C) 2014 Texas Instruments Incorporated - http://www.ti.com/ |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 as |
| * published by the Free Software Foundation. |
| */ |
| /dts-v1/; |
| |
| #include "dra72x.dtsi" |
| |
| / { |
| model = "TI DRA722"; |
| compatible = "ti,dra72-evm", "ti,dra722", "ti,dra72", "ti,dra7"; |
| |
| memory { |
| device_type = "memory"; |
| reg = <0x80000000 0x40000000>; /* 1024 MB */ |
| }; |
| |
| evm_3v3: fixedregulator-evm_3v3 { |
| compatible = "regulator-fixed"; |
| regulator-name = "evm_3v3"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| }; |
| |
| &dra7_pmx_core { |
| i2c1_pins: pinmux_i2c1_pins { |
| pinctrl-single,pins = < |
| 0x400 (PIN_INPUT | MUX_MODE0) /* i2c1_sda.i2c1_sda */ |
| 0x404 (PIN_INPUT | MUX_MODE0) /* i2c1_scl.i2c1_scl */ |
| >; |
| }; |
| |
| nand_default: nand_default { |
| pinctrl-single,pins = < |
| 0x0 (PIN_INPUT | MUX_MODE0) /* gpmc_ad0 */ |
| 0x4 (PIN_INPUT | MUX_MODE0) /* gpmc_ad1 */ |
| 0x8 (PIN_INPUT | MUX_MODE0) /* gpmc_ad2 */ |
| 0xc (PIN_INPUT | MUX_MODE0) /* gpmc_ad3 */ |
| 0x10 (PIN_INPUT | MUX_MODE0) /* gpmc_ad4 */ |
| 0x14 (PIN_INPUT | MUX_MODE0) /* gpmc_ad5 */ |
| 0x18 (PIN_INPUT | MUX_MODE0) /* gpmc_ad6 */ |
| 0x1c (PIN_INPUT | MUX_MODE0) /* gpmc_ad7 */ |
| 0x20 (PIN_INPUT | MUX_MODE0) /* gpmc_ad8 */ |
| 0x24 (PIN_INPUT | MUX_MODE0) /* gpmc_ad9 */ |
| 0x28 (PIN_INPUT | MUX_MODE0) /* gpmc_ad10 */ |
| 0x2c (PIN_INPUT | MUX_MODE0) /* gpmc_ad11 */ |
| 0x30 (PIN_INPUT | MUX_MODE0) /* gpmc_ad12 */ |
| 0x34 (PIN_INPUT | MUX_MODE0) /* gpmc_ad13 */ |
| 0x38 (PIN_INPUT | MUX_MODE0) /* gpmc_ad14 */ |
| 0x3c (PIN_INPUT | MUX_MODE0) /* gpmc_ad15 */ |
| 0xb4 (PIN_OUTPUT | MUX_MODE0) /* gpmc_cs0 */ |
| 0xc4 (PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale */ |
| 0xcc (PIN_OUTPUT | MUX_MODE0) /* gpmc_wen */ |
| 0xc8 (PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren */ |
| 0xd0 (PIN_OUTPUT | MUX_MODE0) /* gpmc_ben0 */ |
| 0xd8 (PIN_INPUT | MUX_MODE0) /* gpmc_wait0 */ |
| >; |
| }; |
| |
| usb1_pins: pinmux_usb1_pins { |
| pinctrl-single,pins = < |
| 0x280 (PIN_INPUT_SLEW | MUX_MODE0) /* usb1_drvvbus */ |
| >; |
| }; |
| |
| usb2_pins: pinmux_usb2_pins { |
| pinctrl-single,pins = < |
| 0x284 (PIN_INPUT_SLEW | MUX_MODE0) /* usb2_drvvbus */ |
| >; |
| }; |
| |
| tps65917_pins_default: tps65917_pins_default { |
| pinctrl-single,pins = < |
| 0x424 (PIN_INPUT_PULLUP | MUX_MODE1) /* wakeup3.sys_nirq1 */ |
| >; |
| }; |
| |
| mmc1_pins_default: mmc1_pins_default { |
| pinctrl-single,pins = < |
| 0x36c (PIN_INPUT | MUX_MODE14) /* mmc1sdcd.gpio219 */ |
| 0x354 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.clk */ |
| 0x358 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */ |
| 0x35c (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */ |
| 0x360 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */ |
| 0x364 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */ |
| 0x368 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */ |
| >; |
| }; |
| |
| mmc2_pins_default: mmc2_pins_default { |
| pinctrl-single,pins = < |
| 0x9c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */ |
| 0xb0 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */ |
| 0xa0 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */ |
| 0xa4 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */ |
| 0xa8 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */ |
| 0xac (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */ |
| 0x8c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */ |
| 0x90 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */ |
| 0x94 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */ |
| 0x98 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */ |
| >; |
| }; |
| |
| dcan1_pins_default: dcan1_pins_default { |
| pinctrl-single,pins = < |
| 0x3d0 (PIN_OUTPUT | MUX_MODE0) /* dcan1_tx */ |
| 0x3d4 (MUX_MODE15) /* dcan1_rx.off */ |
| 0x418 (PULL_DIS | MUX_MODE1) /* wakeup0.dcan1_rx */ |
| >; |
| }; |
| |
| dcan1_pins_sleep: dcan1_pins_sleep { |
| pinctrl-single,pins = < |
| 0x3d0 (MUX_MODE15) /* dcan1_tx.off */ |
| 0x3d4 (MUX_MODE15) /* dcan1_rx.off */ |
| 0x418 (MUX_MODE15) /* wakeup0.off */ |
| >; |
| }; |
| }; |
| |
| &i2c1 { |
| status = "okay"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c1_pins>; |
| clock-frequency = <400000>; |
| |
| tps65917: tps65917@58 { |
| compatible = "ti,tps65917"; |
| reg = <0x58>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&tps65917_pins_default>; |
| |
| interrupts = <GIC_SPI 2 IRQ_TYPE_NONE>; /* IRQ_SYS_1N */ |
| interrupt-parent = <&gic>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| |
| ti,system-power-controller; |
| |
| tps65917_pmic { |
| compatible = "ti,tps65917-pmic"; |
| |
| regulators { |
| smps1_reg: smps1 { |
| /* VDD_MPU */ |
| regulator-name = "smps1"; |
| regulator-min-microvolt = <850000>; |
| regulator-max-microvolt = <1250000>; |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| smps2_reg: smps2 { |
| /* VDD_CORE */ |
| regulator-name = "smps2"; |
| regulator-min-microvolt = <850000>; |
| regulator-max-microvolt = <1060000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| smps3_reg: smps3 { |
| /* VDD_GPU IVA DSPEVE */ |
| regulator-name = "smps3"; |
| regulator-min-microvolt = <850000>; |
| regulator-max-microvolt = <1250000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| smps4_reg: smps4 { |
| /* VDDS1V8 */ |
| regulator-name = "smps4"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| smps5_reg: smps5 { |
| /* VDD_DDR */ |
| regulator-name = "smps5"; |
| regulator-min-microvolt = <1350000>; |
| regulator-max-microvolt = <1350000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| ldo1_reg: ldo1 { |
| /* LDO1_OUT --> SDIO */ |
| regulator-name = "ldo1"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-boot-on; |
| }; |
| |
| ldo2_reg: ldo2 { |
| /* LDO2_OUT --> TP1017 (UNUSED) */ |
| regulator-name = "ldo2"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| |
| ldo3_reg: ldo3 { |
| /* VDDA_1V8_PHY */ |
| regulator-name = "ldo3"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| ldo5_reg: ldo5 { |
| /* VDDA_1V8_PLL */ |
| regulator-name = "ldo5"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| ldo4_reg: ldo4 { |
| /* VDDA_3V_USB: VDDA_USBHS33 */ |
| regulator-name = "ldo4"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-boot-on; |
| }; |
| }; |
| }; |
| |
| tps65917_power_button { |
| compatible = "ti,palmas-pwrbutton"; |
| interrupt-parent = <&tps65917>; |
| interrupts = <1 IRQ_TYPE_NONE>; |
| wakeup-source; |
| ti,palmas-long-press-seconds = <6>; |
| }; |
| }; |
| }; |
| |
| &uart1 { |
| status = "okay"; |
| }; |
| |
| &elm { |
| status = "okay"; |
| }; |
| |
| &gpmc { |
| status = "okay"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&nand_default>; |
| ranges = <0 0 0 0x01000000>; /* minimum GPMC partition = 16MB */ |
| nand@0,0 { |
| /* To use NAND, DIP switch SW5 must be set like so: |
| * SW5.1 (NAND_SELn) = ON (LOW) |
| * SW5.9 (GPMC_WPN) = OFF (HIGH) |
| */ |
| reg = <0 0 4>; /* device IO registers */ |
| ti,nand-ecc-opt = "bch8"; |
| ti,elm-id = <&elm>; |
| nand-bus-width = <16>; |
| gpmc,device-width = <2>; |
| gpmc,sync-clk-ps = <0>; |
| gpmc,cs-on-ns = <0>; |
| gpmc,cs-rd-off-ns = <80>; |
| gpmc,cs-wr-off-ns = <80>; |
| gpmc,adv-on-ns = <0>; |
| gpmc,adv-rd-off-ns = <60>; |
| gpmc,adv-wr-off-ns = <60>; |
| gpmc,we-on-ns = <10>; |
| gpmc,we-off-ns = <50>; |
| gpmc,oe-on-ns = <4>; |
| gpmc,oe-off-ns = <40>; |
| gpmc,access-ns = <40>; |
| gpmc,wr-access-ns = <80>; |
| gpmc,rd-cycle-ns = <80>; |
| gpmc,wr-cycle-ns = <80>; |
| gpmc,bus-turnaround-ns = <0>; |
| gpmc,cycle2cycle-delay-ns = <0>; |
| gpmc,clk-activation-ns = <0>; |
| gpmc,wait-monitoring-ns = <0>; |
| gpmc,wr-data-mux-bus-ns = <0>; |
| /* MTD partition table */ |
| /* All SPL-* partitions are sized to minimal length |
| * which can be independently programmable. For |
| * NAND flash this is equal to size of erase-block */ |
| #address-cells = <1>; |
| #size-cells = <1>; |
| partition@0 { |
| label = "NAND.SPL"; |
| reg = <0x00000000 0x000020000>; |
| }; |
| partition@1 { |
| label = "NAND.SPL.backup1"; |
| reg = <0x00020000 0x00020000>; |
| }; |
| partition@2 { |
| label = "NAND.SPL.backup2"; |
| reg = <0x00040000 0x00020000>; |
| }; |
| partition@3 { |
| label = "NAND.SPL.backup3"; |
| reg = <0x00060000 0x00020000>; |
| }; |
| partition@4 { |
| label = "NAND.u-boot-spl-os"; |
| reg = <0x00080000 0x00040000>; |
| }; |
| partition@5 { |
| label = "NAND.u-boot"; |
| reg = <0x000c0000 0x00100000>; |
| }; |
| partition@6 { |
| label = "NAND.u-boot-env"; |
| reg = <0x001c0000 0x00020000>; |
| }; |
| partition@7 { |
| label = "NAND.u-boot-env.backup1"; |
| reg = <0x001e0000 0x00020000>; |
| }; |
| partition@8 { |
| label = "NAND.kernel"; |
| reg = <0x00200000 0x00800000>; |
| }; |
| partition@9 { |
| label = "NAND.file-system"; |
| reg = <0x00a00000 0x0f600000>; |
| }; |
| }; |
| }; |
| |
| &usb2_phy1 { |
| phy-supply = <&ldo4_reg>; |
| }; |
| |
| &usb2_phy2 { |
| phy-supply = <&ldo4_reg>; |
| }; |
| |
| &usb1 { |
| dr_mode = "peripheral"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&usb1_pins>; |
| }; |
| |
| &usb2 { |
| dr_mode = "host"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&usb2_pins>; |
| }; |
| |
| &mmc1 { |
| status = "okay"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&mmc1_pins_default>; |
| |
| vmmc-supply = <&ldo1_reg>; |
| bus-width = <4>; |
| /* |
| * SDCD signal is not being used here - using the fact that GPIO mode |
| * is a viable alternative |
| */ |
| cd-gpios = <&gpio6 27 0>; |
| }; |
| |
| &mmc2 { |
| /* SW5-3 in ON position */ |
| status = "okay"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&mmc2_pins_default>; |
| |
| vmmc-supply = <&evm_3v3>; |
| bus-width = <8>; |
| ti,non-removable; |
| }; |
| |
| &dra7_pmx_core { |
| cpsw_default: cpsw_default { |
| pinctrl-single,pins = < |
| /* Slave 2 */ |
| 0x198 (PIN_OUTPUT | MUX_MODE3) /* vin2a_d12.rgmii1_txc */ |
| 0x19c (PIN_OUTPUT | MUX_MODE3) /* vin2a_d13.rgmii1_tctl */ |
| 0x1a0 (PIN_OUTPUT | MUX_MODE3) /* vin2a_d14.rgmii1_td3 */ |
| 0x1a4 (PIN_OUTPUT | MUX_MODE3) /* vin2a_d15.rgmii1_td2 */ |
| 0x1a8 (PIN_OUTPUT | MUX_MODE3) /* vin2a_d16.rgmii1_td1 */ |
| 0x1ac (PIN_OUTPUT | MUX_MODE3) /* vin2a_d17.rgmii1_td0 */ |
| 0x1b0 (PIN_INPUT | MUX_MODE3) /* vin2a_d18.rgmii1_rclk */ |
| 0x1b4 (PIN_INPUT | MUX_MODE3) /* vin2a_d19.rgmii1_rctl */ |
| 0x1b8 (PIN_INPUT | MUX_MODE3) /* vin2a_d20.rgmii1_rd3 */ |
| 0x1bc (PIN_INPUT | MUX_MODE3) /* vin2a_d21.rgmii1_rd2 */ |
| 0x1c0 (PIN_INPUT | MUX_MODE3) /* vin2a_d22.rgmii1_rd1 */ |
| 0x1c4 (PIN_INPUT | MUX_MODE3) /* vin2a_d23.rgmii1_rd0 */ |
| >; |
| |
| }; |
| |
| cpsw_sleep: cpsw_sleep { |
| pinctrl-single,pins = < |
| /* Slave 2 */ |
| 0x198 (MUX_MODE15) |
| 0x19c (MUX_MODE15) |
| 0x1a0 (MUX_MODE15) |
| 0x1a4 (MUX_MODE15) |
| 0x1a8 (MUX_MODE15) |
| 0x1ac (MUX_MODE15) |
| 0x1b0 (MUX_MODE15) |
| 0x1b4 (MUX_MODE15) |
| 0x1b8 (MUX_MODE15) |
| 0x1bc (MUX_MODE15) |
| 0x1c0 (MUX_MODE15) |
| 0x1c4 (MUX_MODE15) |
| >; |
| }; |
| |
| davinci_mdio_default: davinci_mdio_default { |
| pinctrl-single,pins = < |
| /* MDIO */ |
| 0x23c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_d.mdio_d */ |
| 0x240 (PIN_INPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ |
| >; |
| }; |
| |
| davinci_mdio_sleep: davinci_mdio_sleep { |
| pinctrl-single,pins = < |
| 0x23c (MUX_MODE15) |
| 0x240 (MUX_MODE15) |
| >; |
| }; |
| }; |
| |
| &mac { |
| status = "okay"; |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&cpsw_default>; |
| pinctrl-1 = <&cpsw_sleep>; |
| }; |
| |
| &cpsw_emac1 { |
| phy_id = <&davinci_mdio>, <3>; |
| phy-mode = "rgmii"; |
| }; |
| |
| &davinci_mdio { |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&davinci_mdio_default>; |
| pinctrl-1 = <&davinci_mdio_sleep>; |
| active_slave = <1>; |
| }; |
| |
| &dcan1 { |
| status = "ok"; |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&dcan1_pins_default>; |
| pinctrl-1 = <&dcan1_pins_sleep>; |
| }; |