[ARM] 4979/1: [AT91] Olimex SAM9-L9260 board support
Support for the Olimex SAM9-L9260 board.
<http://www.olimex.com/dev/sam9-L9260.html>
Original patch from Ivan Vasilev.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
diff --git a/arch/arm/mach-at91/board-sam9-l9260.c b/arch/arm/mach-at91/board-sam9-l9260.c
new file mode 100644
index 0000000..8f76af5
--- /dev/null
+++ b/arch/arm/mach-at91/board-sam9-l9260.c
@@ -0,0 +1,199 @@
+/*
+ * linux/arch/arm/mach-at91/board-sam9-l9260.c
+ *
+ * Copyright (C) 2005 SAN People
+ * Copyright (C) 2006 Atmel
+ * Copyright (C) 2007 Olimex Ltd
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+
+#include <asm/hardware.h>
+#include <asm/setup.h>
+#include <asm/mach-types.h>
+#include <asm/irq.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <asm/arch/board.h>
+#include <asm/arch/gpio.h>
+
+#include "generic.h"
+
+
+static void __init ek_map_io(void)
+{
+ /* Initialize processor: 18.432 MHz crystal */
+ at91sam9260_initialize(18432000);
+
+ /* Setup the LEDs */
+ at91_init_leds(AT91_PIN_PA9, AT91_PIN_PA6);
+
+ /* DBGU on ttyS0. (Rx & Tx only) */
+ at91_register_uart(0, 0, 0);
+
+ /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+ at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+ | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+ | ATMEL_UART_RI);
+
+ /* USART1 on ttyS2. (Rx, Tx, CTS, RTS) */
+ at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
+
+ /* set serial console to ttyS0 (ie, DBGU) */
+ at91_set_serial_console(0);
+}
+
+static void __init ek_init_irq(void)
+{
+ at91sam9260_init_interrupts(NULL);
+}
+
+
+/*
+ * USB Host port
+ */
+static struct at91_usbh_data __initdata ek_usbh_data = {
+ .ports = 2,
+};
+
+/*
+ * USB Device port
+ */
+static struct at91_udc_data __initdata ek_udc_data = {
+ .vbus_pin = AT91_PIN_PC5,
+ .pullup_pin = 0, /* pull-up driven by UDC */
+};
+
+
+/*
+ * SPI devices.
+ */
+static struct spi_board_info ek_spi_devices[] = {
+#if !defined(CONFIG_MMC_AT91)
+ { /* DataFlash chip */
+ .modalias = "mtd_dataflash",
+ .chip_select = 1,
+ .max_speed_hz = 15 * 1000 * 1000,
+ .bus_num = 0,
+ },
+#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD)
+ { /* DataFlash card */
+ .modalias = "mtd_dataflash",
+ .chip_select = 0,
+ .max_speed_hz = 15 * 1000 * 1000,
+ .bus_num = 0,
+ },
+#endif
+#endif
+};
+
+
+/*
+ * MACB Ethernet device
+ */
+static struct at91_eth_data __initdata ek_macb_data = {
+ .phy_irq_pin = AT91_PIN_PA7,
+ .is_rmii = 0,
+};
+
+
+/*
+ * NAND flash
+ */
+static struct mtd_partition __initdata ek_nand_partition[] = {
+ {
+ .name = "Bootloader Area",
+ .offset = 0,
+ .size = 10 * 1024 * 1024,
+ },
+ {
+ .name = "User Area",
+ .offset = 10 * 1024 * 1024,
+ .size = MTDPART_SIZ_FULL,
+ },
+};
+
+static struct mtd_partition * __init nand_partitions(int size, int *num_partitions)
+{
+ *num_partitions = ARRAY_SIZE(ek_nand_partition);
+ return ek_nand_partition;
+}
+
+static struct at91_nand_data __initdata ek_nand_data = {
+ .ale = 21,
+ .cle = 22,
+// .det_pin = ... not connected
+ .rdy_pin = AT91_PIN_PC13,
+ .enable_pin = AT91_PIN_PC14,
+ .partition_info = nand_partitions,
+#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16)
+ .bus_width_16 = 1,
+#else
+ .bus_width_16 = 0,
+#endif
+};
+
+
+/*
+ * MCI (SD/MMC)
+ */
+static struct at91_mmc_data __initdata ek_mmc_data = {
+ .slot_b = 1,
+ .wire4 = 1,
+ .det_pin = AT91_PIN_PC8,
+ .wp_pin = AT91_PIN_PC4,
+// .vcc_pin = ... not connected
+};
+
+static void __init ek_board_init(void)
+{
+ /* Serial */
+ at91_add_device_serial();
+ /* USB Host */
+ at91_add_device_usbh(&ek_usbh_data);
+ /* USB Device */
+ at91_add_device_udc(&ek_udc_data);
+ /* SPI */
+ at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
+ /* NAND */
+ at91_add_device_nand(&ek_nand_data);
+ /* Ethernet */
+ at91_add_device_eth(&ek_macb_data);
+ /* MMC */
+ at91_add_device_mmc(0, &ek_mmc_data);
+ /* I2C */
+ at91_add_device_i2c(NULL, 0);
+}
+
+MACHINE_START(SAM9_L9260, "Olimex SAM9-L9260")
+ /* Maintainer: Olimex */
+ .phys_io = AT91_BASE_SYS,
+ .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc,
+ .boot_params = AT91_SDRAM_BASE + 0x100,
+ .timer = &at91sam926x_timer,
+ .map_io = ek_map_io,
+ .init_irq = ek_init_irq,
+ .init_machine = ek_board_init,
+MACHINE_END