diff --git a/drivers/net/acenic.c b/drivers/net/acenic.c
new file mode 100644
index 0000000..6eea3a8
--- /dev/null
+++ b/drivers/net/acenic.c
@@ -0,0 +1,3271 @@
+/*
+ * acenic.c: Linux driver for the Alteon AceNIC Gigabit Ethernet card
+ *           and other Tigon based cards.
+ *
+ * Copyright 1998-2002 by Jes Sorensen, <jes@trained-monkey.org>.
+ *
+ * Thanks to Alteon and 3Com for providing hardware and documentation
+ * enabling me to write this driver.
+ *
+ * A mailing list for discussing the use of this driver has been
+ * setup, please subscribe to the lists if you have any questions
+ * about the driver. Send mail to linux-acenic-help@sunsite.auc.dk to
+ * see how to subscribe.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * Additional credits:
+ *   Pete Wyckoff <wyckoff@ca.sandia.gov>: Initial Linux/Alpha and trace
+ *       dump support. The trace dump support has not been
+ *       integrated yet however.
+ *   Troy Benjegerdes: Big Endian (PPC) patches.
+ *   Nate Stahl: Better out of memory handling and stats support.
+ *   Aman Singla: Nasty race between interrupt handler and tx code dealing
+ *                with 'testing the tx_ret_csm and setting tx_full'
+ *   David S. Miller <davem@redhat.com>: conversion to new PCI dma mapping
+ *                                       infrastructure and Sparc support
+ *   Pierrick Pinasseau (CERN): For lending me an Ultra 5 to test the
+ *                              driver under Linux/Sparc64
+ *   Matt Domsch <Matt_Domsch@dell.com>: Detect Alteon 1000baseT cards
+ *                                       ETHTOOL_GDRVINFO support
+ *   Chip Salzenberg <chip@valinux.com>: Fix race condition between tx
+ *                                       handler and close() cleanup.
+ *   Ken Aaker <kdaaker@rchland.vnet.ibm.com>: Correct check for whether
+ *                                       memory mapped IO is enabled to
+ *                                       make the driver work on RS/6000.
+ *   Takayoshi Kouchi <kouchi@hpc.bs1.fc.nec.co.jp>: Identifying problem
+ *                                       where the driver would disable
+ *                                       bus master mode if it had to disable
+ *                                       write and invalidate.
+ *   Stephen Hack <stephen_hack@hp.com>: Fixed ace_set_mac_addr for little
+ *                                       endian systems.
+ *   Val Henson <vhenson@esscom.com>:    Reset Jumbo skb producer and
+ *                                       rx producer index when
+ *                                       flushing the Jumbo ring.
+ *   Hans Grobler <grobh@sun.ac.za>:     Memory leak fixes in the
+ *                                       driver init path.
+ *   Grant Grundler <grundler@cup.hp.com>: PCI write posting fixes.
+ */
+
+#include <linux/config.h>
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/version.h>
+#include <linux/types.h>
+#include <linux/errno.h>
+#include <linux/ioport.h>
+#include <linux/pci.h>
+#include <linux/kernel.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/skbuff.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/mm.h>
+#include <linux/highmem.h>
+#include <linux/sockios.h>
+
+#if defined(CONFIG_VLAN_8021Q) || defined(CONFIG_VLAN_8021Q_MODULE)
+#include <linux/if_vlan.h>
+#endif
+
+#ifdef SIOCETHTOOL
+#include <linux/ethtool.h>
+#endif
+
+#include <net/sock.h>
+#include <net/ip.h>
+
+#include <asm/system.h>
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <asm/byteorder.h>
+#include <asm/uaccess.h>
+
+
+#define DRV_NAME "acenic"
+
+#undef INDEX_DEBUG
+
+#ifdef CONFIG_ACENIC_OMIT_TIGON_I
+#define ACE_IS_TIGON_I(ap)	0
+#define ACE_TX_RING_ENTRIES(ap)	MAX_TX_RING_ENTRIES
+#else
+#define ACE_IS_TIGON_I(ap)	(ap->version == 1)
+#define ACE_TX_RING_ENTRIES(ap)	ap->tx_ring_entries
+#endif
+
+#ifndef PCI_VENDOR_ID_ALTEON
+#define PCI_VENDOR_ID_ALTEON		0x12ae	
+#endif
+#ifndef PCI_DEVICE_ID_ALTEON_ACENIC_FIBRE
+#define PCI_DEVICE_ID_ALTEON_ACENIC_FIBRE  0x0001
+#define PCI_DEVICE_ID_ALTEON_ACENIC_COPPER 0x0002
+#endif
+#ifndef PCI_DEVICE_ID_3COM_3C985
+#define PCI_DEVICE_ID_3COM_3C985	0x0001
+#endif
+#ifndef PCI_VENDOR_ID_NETGEAR
+#define PCI_VENDOR_ID_NETGEAR		0x1385
+#define PCI_DEVICE_ID_NETGEAR_GA620	0x620a
+#endif
+#ifndef PCI_DEVICE_ID_NETGEAR_GA620T
+#define PCI_DEVICE_ID_NETGEAR_GA620T	0x630a
+#endif
+
+
+/*
+ * Farallon used the DEC vendor ID by mistake and they seem not
+ * to care - stinky!
+ */
+#ifndef PCI_DEVICE_ID_FARALLON_PN9000SX
+#define PCI_DEVICE_ID_FARALLON_PN9000SX	0x1a
+#endif
+#ifndef PCI_DEVICE_ID_FARALLON_PN9100T
+#define PCI_DEVICE_ID_FARALLON_PN9100T  0xfa
+#endif
+#ifndef PCI_VENDOR_ID_SGI
+#define PCI_VENDOR_ID_SGI		0x10a9
+#endif
+#ifndef PCI_DEVICE_ID_SGI_ACENIC
+#define PCI_DEVICE_ID_SGI_ACENIC	0x0009
+#endif
+
+static struct pci_device_id acenic_pci_tbl[] = {
+	{ PCI_VENDOR_ID_ALTEON, PCI_DEVICE_ID_ALTEON_ACENIC_FIBRE,
+	  PCI_ANY_ID, PCI_ANY_ID, PCI_CLASS_NETWORK_ETHERNET << 8, 0xffff00, },
+	{ PCI_VENDOR_ID_ALTEON, PCI_DEVICE_ID_ALTEON_ACENIC_COPPER,
+	  PCI_ANY_ID, PCI_ANY_ID, PCI_CLASS_NETWORK_ETHERNET << 8, 0xffff00, },
+	{ PCI_VENDOR_ID_3COM, PCI_DEVICE_ID_3COM_3C985,
+	  PCI_ANY_ID, PCI_ANY_ID, PCI_CLASS_NETWORK_ETHERNET << 8, 0xffff00, },
+	{ PCI_VENDOR_ID_NETGEAR, PCI_DEVICE_ID_NETGEAR_GA620,
+	  PCI_ANY_ID, PCI_ANY_ID, PCI_CLASS_NETWORK_ETHERNET << 8, 0xffff00, },
+	{ PCI_VENDOR_ID_NETGEAR, PCI_DEVICE_ID_NETGEAR_GA620T,
+	  PCI_ANY_ID, PCI_ANY_ID, PCI_CLASS_NETWORK_ETHERNET << 8, 0xffff00, },
+	/*
+	 * Farallon used the DEC vendor ID on their cards incorrectly,
+	 * then later Alteon's ID.
+	 */
+	{ PCI_VENDOR_ID_DEC, PCI_DEVICE_ID_FARALLON_PN9000SX,
+	  PCI_ANY_ID, PCI_ANY_ID, PCI_CLASS_NETWORK_ETHERNET << 8, 0xffff00, },
+	{ PCI_VENDOR_ID_ALTEON, PCI_DEVICE_ID_FARALLON_PN9100T,
+	  PCI_ANY_ID, PCI_ANY_ID, PCI_CLASS_NETWORK_ETHERNET << 8, 0xffff00, },
+	{ PCI_VENDOR_ID_SGI, PCI_DEVICE_ID_SGI_ACENIC,
+	  PCI_ANY_ID, PCI_ANY_ID, PCI_CLASS_NETWORK_ETHERNET << 8, 0xffff00, },
+	{ }
+};
+MODULE_DEVICE_TABLE(pci, acenic_pci_tbl);
+
+#ifndef SET_NETDEV_DEV
+#define SET_NETDEV_DEV(net, pdev)	do{} while(0)
+#endif
+
+#if LINUX_VERSION_CODE >= 0x2051c
+#define ace_sync_irq(irq)	synchronize_irq(irq)
+#else
+#define ace_sync_irq(irq)	synchronize_irq()
+#endif
+
+#ifndef offset_in_page
+#define offset_in_page(ptr)	((unsigned long)(ptr) & ~PAGE_MASK)
+#endif
+
+#define ACE_MAX_MOD_PARMS	8
+#define BOARD_IDX_STATIC	0
+#define BOARD_IDX_OVERFLOW	-1
+
+#if (defined(CONFIG_VLAN_8021Q) || defined(CONFIG_VLAN_8021Q_MODULE)) && \
+	defined(NETIF_F_HW_VLAN_RX)
+#define ACENIC_DO_VLAN		1
+#define ACE_RCB_VLAN_FLAG	RCB_FLG_VLAN_ASSIST
+#else
+#define ACENIC_DO_VLAN		0
+#define ACE_RCB_VLAN_FLAG	0
+#endif
+
+#include "acenic.h"
+
+/*
+ * These must be defined before the firmware is included.
+ */
+#define MAX_TEXT_LEN	96*1024
+#define MAX_RODATA_LEN	8*1024
+#define MAX_DATA_LEN	2*1024
+
+#include "acenic_firmware.h"
+
+#ifndef tigon2FwReleaseLocal
+#define tigon2FwReleaseLocal 0
+#endif
+
+/*
+ * This driver currently supports Tigon I and Tigon II based cards
+ * including the Alteon AceNIC, the 3Com 3C985[B] and NetGear
+ * GA620. The driver should also work on the SGI, DEC and Farallon
+ * versions of the card, however I have not been able to test that
+ * myself.
+ *
+ * This card is really neat, it supports receive hardware checksumming
+ * and jumbo frames (up to 9000 bytes) and does a lot of work in the
+ * firmware. Also the programming interface is quite neat, except for
+ * the parts dealing with the i2c eeprom on the card ;-)
+ *
+ * Using jumbo frames:
+ *
+ * To enable jumbo frames, simply specify an mtu between 1500 and 9000
+ * bytes to ifconfig. Jumbo frames can be enabled or disabled at any time
+ * by running `ifconfig eth<X> mtu <MTU>' with <X> being the Ethernet
+ * interface number and <MTU> being the MTU value.
+ *
+ * Module parameters:
+ *
+ * When compiled as a loadable module, the driver allows for a number
+ * of module parameters to be specified. The driver supports the
+ * following module parameters:
+ *
+ *  trace=<val> - Firmware trace level. This requires special traced
+ *                firmware to replace the firmware supplied with
+ *                the driver - for debugging purposes only.
+ *
+ *  link=<val>  - Link state. Normally you want to use the default link
+ *                parameters set by the driver. This can be used to
+ *                override these in case your switch doesn't negotiate
+ *                the link properly. Valid values are:
+ *         0x0001 - Force half duplex link.
+ *         0x0002 - Do not negotiate line speed with the other end.
+ *         0x0010 - 10Mbit/sec link.
+ *         0x0020 - 100Mbit/sec link.
+ *         0x0040 - 1000Mbit/sec link.
+ *         0x0100 - Do not negotiate flow control.
+ *         0x0200 - Enable RX flow control Y
+ *         0x0400 - Enable TX flow control Y (Tigon II NICs only).
+ *                Default value is 0x0270, ie. enable link+flow
+ *                control negotiation. Negotiating the highest
+ *                possible link speed with RX flow control enabled.
+ *
+ *                When disabling link speed negotiation, only one link
+ *                speed is allowed to be specified!
+ *
+ *  tx_coal_tick=<val> - number of coalescing clock ticks (us) allowed
+ *                to wait for more packets to arive before
+ *                interrupting the host, from the time the first
+ *                packet arrives.
+ *
+ *  rx_coal_tick=<val> - number of coalescing clock ticks (us) allowed
+ *                to wait for more packets to arive in the transmit ring,
+ *                before interrupting the host, after transmitting the
+ *                first packet in the ring.
+ *
+ *  max_tx_desc=<val> - maximum number of transmit descriptors
+ *                (packets) transmitted before interrupting the host.
+ *
+ *  max_rx_desc=<val> - maximum number of receive descriptors
+ *                (packets) received before interrupting the host.
+ *
+ *  tx_ratio=<val> - 7 bit value (0 - 63) specifying the split in 64th
+ *                increments of the NIC's on board memory to be used for
+ *                transmit and receive buffers. For the 1MB NIC app. 800KB
+ *                is available, on the 1/2MB NIC app. 300KB is available.
+ *                68KB will always be available as a minimum for both
+ *                directions. The default value is a 50/50 split.
+ *  dis_pci_mem_inval=<val> - disable PCI memory write and invalidate
+ *                operations, default (1) is to always disable this as
+ *                that is what Alteon does on NT. I have not been able
+ *                to measure any real performance differences with
+ *                this on my systems. Set <val>=0 if you want to
+ *                enable these operations.
+ *
+ * If you use more than one NIC, specify the parameters for the
+ * individual NICs with a comma, ie. trace=0,0x00001fff,0 you want to
+ * run tracing on NIC #2 but not on NIC #1 and #3.
+ *
+ * TODO:
+ *
+ * - Proper multicast support.
+ * - NIC dump support.
+ * - More tuning parameters.
+ *
+ * The mini ring is not used under Linux and I am not sure it makes sense
+ * to actually use it.
+ *
+ * New interrupt handler strategy:
+ *
+ * The old interrupt handler worked using the traditional method of
+ * replacing an skbuff with a new one when a packet arrives. However
+ * the rx rings do not need to contain a static number of buffer
+ * descriptors, thus it makes sense to move the memory allocation out
+ * of the main interrupt handler and do it in a bottom half handler
+ * and only allocate new buffers when the number of buffers in the
+ * ring is below a certain threshold. In order to avoid starving the
+ * NIC under heavy load it is however necessary to force allocation
+ * when hitting a minimum threshold. The strategy for alloction is as
+ * follows:
+ *
+ *     RX_LOW_BUF_THRES    - allocate buffers in the bottom half
+ *     RX_PANIC_LOW_THRES  - we are very low on buffers, allocate
+ *                           the buffers in the interrupt handler
+ *     RX_RING_THRES       - maximum number of buffers in the rx ring
+ *     RX_MINI_THRES       - maximum number of buffers in the mini ring
+ *     RX_JUMBO_THRES      - maximum number of buffers in the jumbo ring
+ *
+ * One advantagous side effect of this allocation approach is that the
+ * entire rx processing can be done without holding any spin lock
+ * since the rx rings and registers are totally independent of the tx
+ * ring and its registers.  This of course includes the kmalloc's of
+ * new skb's. Thus start_xmit can run in parallel with rx processing
+ * and the memory allocation on SMP systems.
+ *
+ * Note that running the skb reallocation in a bottom half opens up
+ * another can of races which needs to be handled properly. In
+ * particular it can happen that the interrupt handler tries to run
+ * the reallocation while the bottom half is either running on another
+ * CPU or was interrupted on the same CPU. To get around this the
+ * driver uses bitops to prevent the reallocation routines from being
+ * reentered.
+ *
+ * TX handling can also be done without holding any spin lock, wheee
+ * this is fun! since tx_ret_csm is only written to by the interrupt
+ * handler. The case to be aware of is when shutting down the device
+ * and cleaning up where it is necessary to make sure that
+ * start_xmit() is not running while this is happening. Well DaveM
+ * informs me that this case is already protected against ... bye bye
+ * Mr. Spin Lock, it was nice to know you.
+ *
+ * TX interrupts are now partly disabled so the NIC will only generate
+ * TX interrupts for the number of coal ticks, not for the number of
+ * TX packets in the queue. This should reduce the number of TX only,
+ * ie. when no RX processing is done, interrupts seen.
+ */
+
+/*
+ * Threshold values for RX buffer allocation - the low water marks for
+ * when to start refilling the rings are set to 75% of the ring
+ * sizes. It seems to make sense to refill the rings entirely from the
+ * intrrupt handler once it gets below the panic threshold, that way
+ * we don't risk that the refilling is moved to another CPU when the
+ * one running the interrupt handler just got the slab code hot in its
+ * cache.
+ */
+#define RX_RING_SIZE		72
+#define RX_MINI_SIZE		64
+#define RX_JUMBO_SIZE		48
+
+#define RX_PANIC_STD_THRES	16
+#define RX_PANIC_STD_REFILL	(3*RX_PANIC_STD_THRES)/2
+#define RX_LOW_STD_THRES	(3*RX_RING_SIZE)/4
+#define RX_PANIC_MINI_THRES	12
+#define RX_PANIC_MINI_REFILL	(3*RX_PANIC_MINI_THRES)/2
+#define RX_LOW_MINI_THRES	(3*RX_MINI_SIZE)/4
+#define RX_PANIC_JUMBO_THRES	6
+#define RX_PANIC_JUMBO_REFILL	(3*RX_PANIC_JUMBO_THRES)/2
+#define RX_LOW_JUMBO_THRES	(3*RX_JUMBO_SIZE)/4
+
+
+/*
+ * Size of the mini ring entries, basically these just should be big
+ * enough to take TCP ACKs
+ */
+#define ACE_MINI_SIZE		100
+
+#define ACE_MINI_BUFSIZE	ACE_MINI_SIZE
+#define ACE_STD_BUFSIZE		(ACE_STD_MTU + ETH_HLEN + 4)
+#define ACE_JUMBO_BUFSIZE	(ACE_JUMBO_MTU + ETH_HLEN + 4)
+
+/*
+ * There seems to be a magic difference in the effect between 995 and 996
+ * but little difference between 900 and 995 ... no idea why.
+ *
+ * There is now a default set of tuning parameters which is set, depending
+ * on whether or not the user enables Jumbo frames. It's assumed that if
+ * Jumbo frames are enabled, the user wants optimal tuning for that case.
+ */
+#define DEF_TX_COAL		400 /* 996 */
+#define DEF_TX_MAX_DESC		60  /* was 40 */
+#define DEF_RX_COAL		120 /* 1000 */
+#define DEF_RX_MAX_DESC		25
+#define DEF_TX_RATIO		21 /* 24 */
+
+#define DEF_JUMBO_TX_COAL	20
+#define DEF_JUMBO_TX_MAX_DESC	60
+#define DEF_JUMBO_RX_COAL	30
+#define DEF_JUMBO_RX_MAX_DESC	6
+#define DEF_JUMBO_TX_RATIO	21
+
+#if tigon2FwReleaseLocal < 20001118
+/*
+ * Standard firmware and early modifications duplicate
+ * IRQ load without this flag (coal timer is never reset).
+ * Note that with this flag tx_coal should be less than
+ * time to xmit full tx ring.
+ * 400usec is not so bad for tx ring size of 128.
+ */
+#define TX_COAL_INTS_ONLY	1	/* worth it */
+#else
+/*
+ * With modified firmware, this is not necessary, but still useful.
+ */
+#define TX_COAL_INTS_ONLY	1
+#endif
+
+#define DEF_TRACE		0
+#define DEF_STAT		(2 * TICKS_PER_SEC)
+
+
+static int link[ACE_MAX_MOD_PARMS];
+static int trace[ACE_MAX_MOD_PARMS];
+static int tx_coal_tick[ACE_MAX_MOD_PARMS];
+static int rx_coal_tick[ACE_MAX_MOD_PARMS];
+static int max_tx_desc[ACE_MAX_MOD_PARMS];
+static int max_rx_desc[ACE_MAX_MOD_PARMS];
+static int tx_ratio[ACE_MAX_MOD_PARMS];
+static int dis_pci_mem_inval[ACE_MAX_MOD_PARMS] = {1, 1, 1, 1, 1, 1, 1, 1};
+
+MODULE_AUTHOR("Jes Sorensen <jes@trained-monkey.org>");
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("AceNIC/3C985/GA620 Gigabit Ethernet driver");
+
+module_param_array(link, int, NULL, 0);
+module_param_array(trace, int, NULL, 0);
+module_param_array(tx_coal_tick, int, NULL, 0);
+module_param_array(max_tx_desc, int, NULL, 0);
+module_param_array(rx_coal_tick, int, NULL, 0);
+module_param_array(max_rx_desc, int, NULL, 0);
+module_param_array(tx_ratio, int, NULL, 0);
+MODULE_PARM_DESC(link, "AceNIC/3C985/NetGear link state");
+MODULE_PARM_DESC(trace, "AceNIC/3C985/NetGear firmware trace level");
+MODULE_PARM_DESC(tx_coal_tick, "AceNIC/3C985/GA620 max clock ticks to wait from first tx descriptor arrives");
+MODULE_PARM_DESC(max_tx_desc, "AceNIC/3C985/GA620 max number of transmit descriptors to wait");
+MODULE_PARM_DESC(rx_coal_tick, "AceNIC/3C985/GA620 max clock ticks to wait from first rx descriptor arrives");
+MODULE_PARM_DESC(max_rx_desc, "AceNIC/3C985/GA620 max number of receive descriptors to wait");
+MODULE_PARM_DESC(tx_ratio, "AceNIC/3C985/GA620 ratio of NIC memory used for TX/RX descriptors (range 0-63)");
+
+
+static char version[] __devinitdata = 
+  "acenic.c: v0.92 08/05/2002  Jes Sorensen, linux-acenic@SunSITE.dk\n"
+  "                            http://home.cern.ch/~jes/gige/acenic.html\n";
+
+static int ace_get_settings(struct net_device *, struct ethtool_cmd *);
+static int ace_set_settings(struct net_device *, struct ethtool_cmd *);
+static void ace_get_drvinfo(struct net_device *, struct ethtool_drvinfo *);
+
+static struct ethtool_ops ace_ethtool_ops = {
+	.get_settings = ace_get_settings,
+	.set_settings = ace_set_settings,
+	.get_drvinfo = ace_get_drvinfo,
+};
+
+static void ace_watchdog(struct net_device *dev);
+
+static int __devinit acenic_probe_one(struct pci_dev *pdev,
+		const struct pci_device_id *id)
+{
+	struct net_device *dev;
+	struct ace_private *ap;
+	static int boards_found;
+
+	dev = alloc_etherdev(sizeof(struct ace_private));
+	if (dev == NULL) {
+		printk(KERN_ERR "acenic: Unable to allocate "
+		       "net_device structure!\n");
+		return -ENOMEM;
+	}
+
+	SET_MODULE_OWNER(dev);
+	SET_NETDEV_DEV(dev, &pdev->dev);
+
+	ap = dev->priv;
+	ap->pdev = pdev;
+	ap->name = pci_name(pdev);
+
+	dev->features |= NETIF_F_SG | NETIF_F_IP_CSUM;
+#if ACENIC_DO_VLAN
+	dev->features |= NETIF_F_HW_VLAN_TX | NETIF_F_HW_VLAN_RX;
+	dev->vlan_rx_register = ace_vlan_rx_register;
+	dev->vlan_rx_kill_vid = ace_vlan_rx_kill_vid;
+#endif
+	if (1) {
+		dev->tx_timeout = &ace_watchdog;
+		dev->watchdog_timeo = 5*HZ;
+	}
+
+	dev->open = &ace_open;
+	dev->stop = &ace_close;
+	dev->hard_start_xmit = &ace_start_xmit;
+	dev->get_stats = &ace_get_stats;
+	dev->set_multicast_list = &ace_set_multicast_list;
+	SET_ETHTOOL_OPS(dev, &ace_ethtool_ops);
+	dev->set_mac_address = &ace_set_mac_addr;
+	dev->change_mtu = &ace_change_mtu;
+
+	/* we only display this string ONCE */
+	if (!boards_found)
+		printk(version);
+
+	if (pci_enable_device(pdev))
+		goto fail_free_netdev;
+
+	/*
+	 * Enable master mode before we start playing with the
+	 * pci_command word since pci_set_master() will modify
+	 * it.
+	 */
+	pci_set_master(pdev);
+
+	pci_read_config_word(pdev, PCI_COMMAND, &ap->pci_command);
+
+	/* OpenFirmware on Mac's does not set this - DOH.. */ 
+	if (!(ap->pci_command & PCI_COMMAND_MEMORY)) {
+		printk(KERN_INFO "%s: Enabling PCI Memory Mapped "
+		       "access - was not enabled by BIOS/Firmware\n",
+		       ap->name);
+		ap->pci_command = ap->pci_command | PCI_COMMAND_MEMORY;
+		pci_write_config_word(ap->pdev, PCI_COMMAND,
+				      ap->pci_command);
+		wmb();
+	}
+
+	pci_read_config_byte(pdev, PCI_LATENCY_TIMER, &ap->pci_latency);
+	if (ap->pci_latency <= 0x40) {
+		ap->pci_latency = 0x40;
+		pci_write_config_byte(pdev, PCI_LATENCY_TIMER, ap->pci_latency);
+	}
+
+	/*
+	 * Remap the regs into kernel space - this is abuse of
+	 * dev->base_addr since it was means for I/O port
+	 * addresses but who gives a damn.
+	 */
+	dev->base_addr = pci_resource_start(pdev, 0);
+	ap->regs = ioremap(dev->base_addr, 0x4000);
+	if (!ap->regs) {
+		printk(KERN_ERR "%s:  Unable to map I/O register, "
+		       "AceNIC %i will be disabled.\n",
+		       ap->name, boards_found);
+		goto fail_free_netdev;
+	}
+
+	switch(pdev->vendor) {
+	case PCI_VENDOR_ID_ALTEON:
+		if (pdev->device == PCI_DEVICE_ID_FARALLON_PN9100T) {
+			printk(KERN_INFO "%s: Farallon PN9100-T ",
+			       ap->name);
+		} else {
+			printk(KERN_INFO "%s: Alteon AceNIC ",
+			       ap->name);
+		}
+		break;
+	case PCI_VENDOR_ID_3COM:
+		printk(KERN_INFO "%s: 3Com 3C985 ", ap->name);
+		break;
+	case PCI_VENDOR_ID_NETGEAR:
+		printk(KERN_INFO "%s: NetGear GA620 ", ap->name);
+		break;
+	case PCI_VENDOR_ID_DEC:
+		if (pdev->device == PCI_DEVICE_ID_FARALLON_PN9000SX) {
+			printk(KERN_INFO "%s: Farallon PN9000-SX ",
+			       ap->name);
+			break;
+		}
+	case PCI_VENDOR_ID_SGI:
+		printk(KERN_INFO "%s: SGI AceNIC ", ap->name);
+		break;
+	default:
+		printk(KERN_INFO "%s: Unknown AceNIC ", ap->name);
+		break;
+	}
+
+	printk("Gigabit Ethernet at 0x%08lx, ", dev->base_addr);
+#ifdef __sparc__
+	printk("irq %s\n", __irq_itoa(pdev->irq));
+#else
+	printk("irq %i\n", pdev->irq);
+#endif
+
+#ifdef CONFIG_ACENIC_OMIT_TIGON_I
+	if ((readl(&ap->regs->HostCtrl) >> 28) == 4) {
+		printk(KERN_ERR "%s: Driver compiled without Tigon I"
+		       " support - NIC disabled\n", dev->name);
+		goto fail_uninit;
+	}
+#endif
+
+	if (ace_allocate_descriptors(dev))
+		goto fail_free_netdev;
+
+#ifdef MODULE
+	if (boards_found >= ACE_MAX_MOD_PARMS)
+		ap->board_idx = BOARD_IDX_OVERFLOW;
+	else
+		ap->board_idx = boards_found;
+#else
+	ap->board_idx = BOARD_IDX_STATIC;
+#endif
+
+	if (ace_init(dev))
+		goto fail_free_netdev;
+
+	if (register_netdev(dev)) {
+		printk(KERN_ERR "acenic: device registration failed\n");
+		goto fail_uninit;
+	}
+	ap->name = dev->name;
+
+	if (ap->pci_using_dac)
+		dev->features |= NETIF_F_HIGHDMA;
+
+	pci_set_drvdata(pdev, dev);
+
+	boards_found++;
+	return 0;
+
+ fail_uninit:
+	ace_init_cleanup(dev);
+ fail_free_netdev:
+	free_netdev(dev);
+	return -ENODEV;
+}
+
+static void __devexit acenic_remove_one(struct pci_dev *pdev)
+{
+	struct net_device *dev = pci_get_drvdata(pdev);
+	struct ace_private *ap = netdev_priv(dev);
+	struct ace_regs __iomem *regs = ap->regs;
+	short i;
+
+	unregister_netdev(dev);
+
+	writel(readl(&regs->CpuCtrl) | CPU_HALT, &regs->CpuCtrl);
+	if (ap->version >= 2)
+		writel(readl(&regs->CpuBCtrl) | CPU_HALT, &regs->CpuBCtrl);
+	
+	/*
+	 * This clears any pending interrupts
+	 */
+	writel(1, &regs->Mb0Lo);
+	readl(&regs->CpuCtrl);	/* flush */
+
+	/*
+	 * Make sure no other CPUs are processing interrupts
+	 * on the card before the buffers are being released.
+	 * Otherwise one might experience some `interesting'
+	 * effects.
+	 *
+	 * Then release the RX buffers - jumbo buffers were
+	 * already released in ace_close().
+	 */
+	ace_sync_irq(dev->irq);
+
+	for (i = 0; i < RX_STD_RING_ENTRIES; i++) {
+		struct sk_buff *skb = ap->skb->rx_std_skbuff[i].skb;
+
+		if (skb) {
+			struct ring_info *ringp;
+			dma_addr_t mapping;
+
+			ringp = &ap->skb->rx_std_skbuff[i];
+			mapping = pci_unmap_addr(ringp, mapping);
+			pci_unmap_page(ap->pdev, mapping,
+				       ACE_STD_BUFSIZE,
+				       PCI_DMA_FROMDEVICE);
+
+			ap->rx_std_ring[i].size = 0;
+			ap->skb->rx_std_skbuff[i].skb = NULL;
+			dev_kfree_skb(skb);
+		}
+	}
+
+	if (ap->version >= 2) {
+		for (i = 0; i < RX_MINI_RING_ENTRIES; i++) {
+			struct sk_buff *skb = ap->skb->rx_mini_skbuff[i].skb;
+
+			if (skb) {
+				struct ring_info *ringp;
+				dma_addr_t mapping;
+
+				ringp = &ap->skb->rx_mini_skbuff[i];
+				mapping = pci_unmap_addr(ringp,mapping);
+				pci_unmap_page(ap->pdev, mapping,
+					       ACE_MINI_BUFSIZE,
+					       PCI_DMA_FROMDEVICE);
+
+				ap->rx_mini_ring[i].size = 0;
+				ap->skb->rx_mini_skbuff[i].skb = NULL;
+				dev_kfree_skb(skb);
+			}
+		}
+	}
+
+	for (i = 0; i < RX_JUMBO_RING_ENTRIES; i++) {
+		struct sk_buff *skb = ap->skb->rx_jumbo_skbuff[i].skb;
+		if (skb) {
+			struct ring_info *ringp;
+			dma_addr_t mapping;
+
+			ringp = &ap->skb->rx_jumbo_skbuff[i];
+			mapping = pci_unmap_addr(ringp, mapping);
+			pci_unmap_page(ap->pdev, mapping,
+				       ACE_JUMBO_BUFSIZE,
+				       PCI_DMA_FROMDEVICE);
+
+			ap->rx_jumbo_ring[i].size = 0;
+			ap->skb->rx_jumbo_skbuff[i].skb = NULL;
+			dev_kfree_skb(skb);
+		}
+	}
+
+	ace_init_cleanup(dev);
+	free_netdev(dev);
+}
+
+static struct pci_driver acenic_pci_driver = {
+	.name		= "acenic",
+	.id_table	= acenic_pci_tbl,
+	.probe		= acenic_probe_one,
+	.remove		= __devexit_p(acenic_remove_one),
+};
+
+static int __init acenic_init(void)
+{
+	return pci_module_init(&acenic_pci_driver);
+}
+
+static void __exit acenic_exit(void)
+{
+	pci_unregister_driver(&acenic_pci_driver);
+}
+
+module_init(acenic_init);
+module_exit(acenic_exit);
+
+static void ace_free_descriptors(struct net_device *dev)
+{
+	struct ace_private *ap = netdev_priv(dev);
+	int size;
+
+	if (ap->rx_std_ring != NULL) {
+		size = (sizeof(struct rx_desc) *
+			(RX_STD_RING_ENTRIES +
+			 RX_JUMBO_RING_ENTRIES +
+			 RX_MINI_RING_ENTRIES +
+			 RX_RETURN_RING_ENTRIES));
+		pci_free_consistent(ap->pdev, size, ap->rx_std_ring,
+				    ap->rx_ring_base_dma);
+		ap->rx_std_ring = NULL;
+		ap->rx_jumbo_ring = NULL;
+		ap->rx_mini_ring = NULL;
+		ap->rx_return_ring = NULL;
+	}
+	if (ap->evt_ring != NULL) {
+		size = (sizeof(struct event) * EVT_RING_ENTRIES);
+		pci_free_consistent(ap->pdev, size, ap->evt_ring,
+				    ap->evt_ring_dma);
+		ap->evt_ring = NULL;
+	}
+	if (ap->tx_ring != NULL && !ACE_IS_TIGON_I(ap)) {
+		size = (sizeof(struct tx_desc) * MAX_TX_RING_ENTRIES);
+		pci_free_consistent(ap->pdev, size, ap->tx_ring,
+				    ap->tx_ring_dma);
+	}
+	ap->tx_ring = NULL;
+
+	if (ap->evt_prd != NULL) {
+		pci_free_consistent(ap->pdev, sizeof(u32),
+				    (void *)ap->evt_prd, ap->evt_prd_dma);
+		ap->evt_prd = NULL;
+	}
+	if (ap->rx_ret_prd != NULL) {
+		pci_free_consistent(ap->pdev, sizeof(u32),
+				    (void *)ap->rx_ret_prd,
+				    ap->rx_ret_prd_dma);
+		ap->rx_ret_prd = NULL;
+	}
+	if (ap->tx_csm != NULL) {
+		pci_free_consistent(ap->pdev, sizeof(u32),
+				    (void *)ap->tx_csm, ap->tx_csm_dma);
+		ap->tx_csm = NULL;
+	}
+}
+
+
+static int ace_allocate_descriptors(struct net_device *dev)
+{
+	struct ace_private *ap = netdev_priv(dev);
+	int size;
+
+	size = (sizeof(struct rx_desc) *
+		(RX_STD_RING_ENTRIES +
+		 RX_JUMBO_RING_ENTRIES +
+		 RX_MINI_RING_ENTRIES +
+		 RX_RETURN_RING_ENTRIES));
+
+	ap->rx_std_ring = pci_alloc_consistent(ap->pdev, size,
+					       &ap->rx_ring_base_dma);
+	if (ap->rx_std_ring == NULL)
+		goto fail;
+
+	ap->rx_jumbo_ring = ap->rx_std_ring + RX_STD_RING_ENTRIES;
+	ap->rx_mini_ring = ap->rx_jumbo_ring + RX_JUMBO_RING_ENTRIES;
+	ap->rx_return_ring = ap->rx_mini_ring + RX_MINI_RING_ENTRIES;
+
+	size = (sizeof(struct event) * EVT_RING_ENTRIES);
+
+	ap->evt_ring = pci_alloc_consistent(ap->pdev, size, &ap->evt_ring_dma);
+
+	if (ap->evt_ring == NULL)
+		goto fail;
+
+	/*
+	 * Only allocate a host TX ring for the Tigon II, the Tigon I
+	 * has to use PCI registers for this ;-(
+	 */
+	if (!ACE_IS_TIGON_I(ap)) {
+		size = (sizeof(struct tx_desc) * MAX_TX_RING_ENTRIES);
+
+		ap->tx_ring = pci_alloc_consistent(ap->pdev, size,
+						   &ap->tx_ring_dma);
+
+		if (ap->tx_ring == NULL)
+			goto fail;
+	}
+
+	ap->evt_prd = pci_alloc_consistent(ap->pdev, sizeof(u32),
+					   &ap->evt_prd_dma);
+	if (ap->evt_prd == NULL)
+		goto fail;
+
+	ap->rx_ret_prd = pci_alloc_consistent(ap->pdev, sizeof(u32),
+					      &ap->rx_ret_prd_dma);
+	if (ap->rx_ret_prd == NULL)
+		goto fail;
+
+	ap->tx_csm = pci_alloc_consistent(ap->pdev, sizeof(u32),
+					  &ap->tx_csm_dma);
+	if (ap->tx_csm == NULL)
+		goto fail;
+
+	return 0;
+
+fail:
+	/* Clean up. */
+	ace_init_cleanup(dev);
+	return 1;
+}
+
+
+/*
+ * Generic cleanup handling data allocated during init. Used when the
+ * module is unloaded or if an error occurs during initialization
+ */
+static void ace_init_cleanup(struct net_device *dev)
+{
+	struct ace_private *ap;
+
+	ap = netdev_priv(dev);
+
+	ace_free_descriptors(dev);
+
+	if (ap->info)
+		pci_free_consistent(ap->pdev, sizeof(struct ace_info),
+				    ap->info, ap->info_dma);
+	if (ap->skb)
+		kfree(ap->skb);
+	if (ap->trace_buf)
+		kfree(ap->trace_buf);
+
+	if (dev->irq)
+		free_irq(dev->irq, dev);
+
+	iounmap(ap->regs);
+}
+
+
+/*
+ * Commands are considered to be slow.
+ */
+static inline void ace_issue_cmd(struct ace_regs __iomem *regs, struct cmd *cmd)
+{
+	u32 idx;
+
+	idx = readl(&regs->CmdPrd);
+
+	writel(*(u32 *)(cmd), &regs->CmdRng[idx]);
+	idx = (idx + 1) % CMD_RING_ENTRIES;
+
+	writel(idx, &regs->CmdPrd);
+}
+
+
+static int __devinit ace_init(struct net_device *dev)
+{
+	struct ace_private *ap;
+	struct ace_regs __iomem *regs;
+	struct ace_info *info = NULL;
+	struct pci_dev *pdev;
+	unsigned long myjif;
+	u64 tmp_ptr;
+	u32 tig_ver, mac1, mac2, tmp, pci_state;
+	int board_idx, ecode = 0;
+	short i;
+	unsigned char cache_size;
+
+	ap = netdev_priv(dev);
+	regs = ap->regs;
+
+	board_idx = ap->board_idx;
+
+	/*
+	 * aman@sgi.com - its useful to do a NIC reset here to
+	 * address the `Firmware not running' problem subsequent
+	 * to any crashes involving the NIC
+	 */
+	writel(HW_RESET | (HW_RESET << 24), &regs->HostCtrl);
+	readl(&regs->HostCtrl);		/* PCI write posting */
+	udelay(5);
+
+	/*
+	 * Don't access any other registers before this point!
+	 */
+#ifdef __BIG_ENDIAN
+	/*
+	 * This will most likely need BYTE_SWAP once we switch
+	 * to using __raw_writel()
+	 */
+	writel((WORD_SWAP | CLR_INT | ((WORD_SWAP | CLR_INT) << 24)),
+	       &regs->HostCtrl);
+#else
+	writel((CLR_INT | WORD_SWAP | ((CLR_INT | WORD_SWAP) << 24)),
+	       &regs->HostCtrl);
+#endif
+	readl(&regs->HostCtrl);		/* PCI write posting */
+
+	/*
+	 * Stop the NIC CPU and clear pending interrupts
+	 */
+	writel(readl(&regs->CpuCtrl) | CPU_HALT, &regs->CpuCtrl);
+	readl(&regs->CpuCtrl);		/* PCI write posting */
+	writel(0, &regs->Mb0Lo);
+
+	tig_ver = readl(&regs->HostCtrl) >> 28;
+
+	switch(tig_ver){
+#ifndef CONFIG_ACENIC_OMIT_TIGON_I
+	case 4:
+	case 5:
+		printk(KERN_INFO "  Tigon I  (Rev. %i), Firmware: %i.%i.%i, ",
+		       tig_ver, tigonFwReleaseMajor, tigonFwReleaseMinor,
+		       tigonFwReleaseFix);
+		writel(0, &regs->LocalCtrl);
+		ap->version = 1;
+		ap->tx_ring_entries = TIGON_I_TX_RING_ENTRIES;
+		break;
+#endif
+	case 6:
+		printk(KERN_INFO "  Tigon II (Rev. %i), Firmware: %i.%i.%i, ",
+		       tig_ver, tigon2FwReleaseMajor, tigon2FwReleaseMinor,
+		       tigon2FwReleaseFix);
+		writel(readl(&regs->CpuBCtrl) | CPU_HALT, &regs->CpuBCtrl);
+		readl(&regs->CpuBCtrl);		/* PCI write posting */
+		/*
+		 * The SRAM bank size does _not_ indicate the amount
+		 * of memory on the card, it controls the _bank_ size!
+		 * Ie. a 1MB AceNIC will have two banks of 512KB.
+		 */
+		writel(SRAM_BANK_512K, &regs->LocalCtrl);
+		writel(SYNC_SRAM_TIMING, &regs->MiscCfg);
+		ap->version = 2;
+		ap->tx_ring_entries = MAX_TX_RING_ENTRIES;
+		break;
+	default:
+		printk(KERN_WARNING "  Unsupported Tigon version detected "
+		       "(%i)\n", tig_ver);
+		ecode = -ENODEV;
+		goto init_error;
+	}
+
+	/*
+	 * ModeStat _must_ be set after the SRAM settings as this change
+	 * seems to corrupt the ModeStat and possible other registers.
+	 * The SRAM settings survive resets and setting it to the same
+	 * value a second time works as well. This is what caused the
+	 * `Firmware not running' problem on the Tigon II.
+	 */
+#ifdef __BIG_ENDIAN
+	writel(ACE_BYTE_SWAP_DMA | ACE_WARN | ACE_FATAL | ACE_BYTE_SWAP_BD |
+	       ACE_WORD_SWAP_BD | ACE_NO_JUMBO_FRAG, &regs->ModeStat);
+#else
+	writel(ACE_BYTE_SWAP_DMA | ACE_WARN | ACE_FATAL |
+	       ACE_WORD_SWAP_BD | ACE_NO_JUMBO_FRAG, &regs->ModeStat);
+#endif
+	readl(&regs->ModeStat);		/* PCI write posting */
+
+	mac1 = 0;
+	for(i = 0; i < 4; i++) {
+		mac1 = mac1 << 8;
+		tmp = read_eeprom_byte(dev, 0x8c+i);
+		if (tmp < 0) {
+			ecode = -EIO;
+			goto init_error;
+		} else
+			mac1 |= (tmp & 0xff);
+	}
+	mac2 = 0;
+	for(i = 4; i < 8; i++) {
+		mac2 = mac2 << 8;
+		tmp = read_eeprom_byte(dev, 0x8c+i);
+		if (tmp < 0) {
+			ecode = -EIO;
+			goto init_error;
+		} else
+			mac2 |= (tmp & 0xff);
+	}
+
+	writel(mac1, &regs->MacAddrHi);
+	writel(mac2, &regs->MacAddrLo);
+
+	printk("MAC: %02x:%02x:%02x:%02x:%02x:%02x\n",
+	       (mac1 >> 8) & 0xff, mac1 & 0xff, (mac2 >> 24) &0xff,
+	       (mac2 >> 16) & 0xff, (mac2 >> 8) & 0xff, mac2 & 0xff);
+
+	dev->dev_addr[0] = (mac1 >> 8) & 0xff;
+	dev->dev_addr[1] = mac1 & 0xff;
+	dev->dev_addr[2] = (mac2 >> 24) & 0xff;
+	dev->dev_addr[3] = (mac2 >> 16) & 0xff;
+	dev->dev_addr[4] = (mac2 >> 8) & 0xff;
+	dev->dev_addr[5] = mac2 & 0xff;
+
+	/*
+	 * Looks like this is necessary to deal with on all architectures,
+	 * even this %$#%$# N440BX Intel based thing doesn't get it right.
+	 * Ie. having two NICs in the machine, one will have the cache
+	 * line set at boot time, the other will not.
+	 */
+	pdev = ap->pdev;
+	pci_read_config_byte(pdev, PCI_CACHE_LINE_SIZE, &cache_size);
+	cache_size <<= 2;
+	if (cache_size != SMP_CACHE_BYTES) {
+		printk(KERN_INFO "  PCI cache line size set incorrectly "
+		       "(%i bytes) by BIOS/FW, ", cache_size);
+		if (cache_size > SMP_CACHE_BYTES)
+			printk("expecting %i\n", SMP_CACHE_BYTES);
+		else {
+			printk("correcting to %i\n", SMP_CACHE_BYTES);
+			pci_write_config_byte(pdev, PCI_CACHE_LINE_SIZE,
+					      SMP_CACHE_BYTES >> 2);
+		}
+	}
+
+	pci_state = readl(&regs->PciState);
+	printk(KERN_INFO "  PCI bus width: %i bits, speed: %iMHz, "
+	       "latency: %i clks\n",
+	       	(pci_state & PCI_32BIT) ? 32 : 64,
+		(pci_state & PCI_66MHZ) ? 66 : 33, 
+		ap->pci_latency);
+
+	/*
+	 * Set the max DMA transfer size. Seems that for most systems
+	 * the performance is better when no MAX parameter is
+	 * set. However for systems enabling PCI write and invalidate,
+	 * DMA writes must be set to the L1 cache line size to get
+	 * optimal performance.
+	 *
+	 * The default is now to turn the PCI write and invalidate off
+	 * - that is what Alteon does for NT.
+	 */
+	tmp = READ_CMD_MEM | WRITE_CMD_MEM;
+	if (ap->version >= 2) {
+		tmp |= (MEM_READ_MULTIPLE | (pci_state & PCI_66MHZ));
+		/*
+		 * Tuning parameters only supported for 8 cards
+		 */
+		if (board_idx == BOARD_IDX_OVERFLOW ||
+		    dis_pci_mem_inval[board_idx]) {
+			if (ap->pci_command & PCI_COMMAND_INVALIDATE) {
+				ap->pci_command &= ~PCI_COMMAND_INVALIDATE;
+				pci_write_config_word(pdev, PCI_COMMAND,
+						      ap->pci_command);
+				printk(KERN_INFO "  Disabling PCI memory "
+				       "write and invalidate\n");
+			}
+		} else if (ap->pci_command & PCI_COMMAND_INVALIDATE) {
+			printk(KERN_INFO "  PCI memory write & invalidate "
+			       "enabled by BIOS, enabling counter measures\n");
+
+			switch(SMP_CACHE_BYTES) {
+			case 16:
+				tmp |= DMA_WRITE_MAX_16;
+				break;
+			case 32:
+				tmp |= DMA_WRITE_MAX_32;
+				break;
+			case 64:
+				tmp |= DMA_WRITE_MAX_64;
+				break;
+			case 128:
+				tmp |= DMA_WRITE_MAX_128;
+				break;
+			default:
+				printk(KERN_INFO "  Cache line size %i not "
+				       "supported, PCI write and invalidate "
+				       "disabled\n", SMP_CACHE_BYTES);
+				ap->pci_command &= ~PCI_COMMAND_INVALIDATE;
+				pci_write_config_word(pdev, PCI_COMMAND,
+						      ap->pci_command);
+			}
+		}
+	}
+
+#ifdef __sparc__
+	/*
+	 * On this platform, we know what the best dma settings
+	 * are.  We use 64-byte maximum bursts, because if we
+	 * burst larger than the cache line size (or even cross
+	 * a 64byte boundary in a single burst) the UltraSparc
+	 * PCI controller will disconnect at 64-byte multiples.
+	 *
+	 * Read-multiple will be properly enabled above, and when
+	 * set will give the PCI controller proper hints about
+	 * prefetching.
+	 */
+	tmp &= ~DMA_READ_WRITE_MASK;
+	tmp |= DMA_READ_MAX_64;
+	tmp |= DMA_WRITE_MAX_64;
+#endif
+#ifdef __alpha__
+	tmp &= ~DMA_READ_WRITE_MASK;
+	tmp |= DMA_READ_MAX_128;
+	/*
+	 * All the docs say MUST NOT. Well, I did.
+	 * Nothing terrible happens, if we load wrong size.
+	 * Bit w&i still works better!
+	 */
+	tmp |= DMA_WRITE_MAX_128;
+#endif
+	writel(tmp, &regs->PciState);
+
+#if 0
+	/*
+	 * The Host PCI bus controller driver has to set FBB.
+	 * If all devices on that PCI bus support FBB, then the controller
+	 * can enable FBB support in the Host PCI Bus controller (or on
+	 * the PCI-PCI bridge if that applies).
+	 * -ggg
+	 */
+	/*
+	 * I have received reports from people having problems when this
+	 * bit is enabled.
+	 */
+	if (!(ap->pci_command & PCI_COMMAND_FAST_BACK)) {
+		printk(KERN_INFO "  Enabling PCI Fast Back to Back\n");
+		ap->pci_command |= PCI_COMMAND_FAST_BACK;
+		pci_write_config_word(pdev, PCI_COMMAND, ap->pci_command);
+	}
+#endif
+		
+	/*
+	 * Configure DMA attributes.
+	 */
+	if (!pci_set_dma_mask(pdev, 0xffffffffffffffffULL)) {
+		ap->pci_using_dac = 1;
+	} else if (!pci_set_dma_mask(pdev, 0xffffffffULL)) {
+		ap->pci_using_dac = 0;
+	} else {
+		ecode = -ENODEV;
+		goto init_error;
+	}
+
+	/*
+	 * Initialize the generic info block and the command+event rings
+	 * and the control blocks for the transmit and receive rings
+	 * as they need to be setup once and for all.
+	 */
+	if (!(info = pci_alloc_consistent(ap->pdev, sizeof(struct ace_info),
+					  &ap->info_dma))) {
+		ecode = -EAGAIN;
+		goto init_error;
+	}
+	ap->info = info;
+
+	/*
+	 * Get the memory for the skb rings.
+	 */
+	if (!(ap->skb = kmalloc(sizeof(struct ace_skb), GFP_KERNEL))) {
+		ecode = -EAGAIN;
+		goto init_error;
+	}
+
+	ecode = request_irq(pdev->irq, ace_interrupt, SA_SHIRQ,
+			    DRV_NAME, dev);
+	if (ecode) {
+		printk(KERN_WARNING "%s: Requested IRQ %d is busy\n",
+		       DRV_NAME, pdev->irq);
+		goto init_error;
+	} else
+		dev->irq = pdev->irq;
+
+#ifdef INDEX_DEBUG
+	spin_lock_init(&ap->debug_lock);
+	ap->last_tx = ACE_TX_RING_ENTRIES(ap) - 1;
+	ap->last_std_rx = 0;
+	ap->last_mini_rx = 0;
+#endif
+
+	memset(ap->info, 0, sizeof(struct ace_info));
+	memset(ap->skb, 0, sizeof(struct ace_skb));
+
+	ace_load_firmware(dev);
+	ap->fw_running = 0;
+
+	tmp_ptr = ap->info_dma;
+	writel(tmp_ptr >> 32, &regs->InfoPtrHi);
+	writel(tmp_ptr & 0xffffffff, &regs->InfoPtrLo);
+
+	memset(ap->evt_ring, 0, EVT_RING_ENTRIES * sizeof(struct event));
+
+	set_aceaddr(&info->evt_ctrl.rngptr, ap->evt_ring_dma);
+	info->evt_ctrl.flags = 0;
+
+	*(ap->evt_prd) = 0;
+	wmb();
+	set_aceaddr(&info->evt_prd_ptr, ap->evt_prd_dma);
+	writel(0, &regs->EvtCsm);
+
+	set_aceaddr(&info->cmd_ctrl.rngptr, 0x100);
+	info->cmd_ctrl.flags = 0;
+	info->cmd_ctrl.max_len = 0;
+
+	for (i = 0; i < CMD_RING_ENTRIES; i++)
+		writel(0, &regs->CmdRng[i]);
+
+	writel(0, &regs->CmdPrd);
+	writel(0, &regs->CmdCsm);
+
+	tmp_ptr = ap->info_dma;
+	tmp_ptr += (unsigned long) &(((struct ace_info *)0)->s.stats);
+	set_aceaddr(&info->stats2_ptr, (dma_addr_t) tmp_ptr);
+
+	set_aceaddr(&info->rx_std_ctrl.rngptr, ap->rx_ring_base_dma);
+	info->rx_std_ctrl.max_len = ACE_STD_BUFSIZE;
+	info->rx_std_ctrl.flags =
+	  RCB_FLG_TCP_UDP_SUM | RCB_FLG_NO_PSEUDO_HDR | ACE_RCB_VLAN_FLAG;
+
+	memset(ap->rx_std_ring, 0,
+	       RX_STD_RING_ENTRIES * sizeof(struct rx_desc));
+
+	for (i = 0; i < RX_STD_RING_ENTRIES; i++)
+		ap->rx_std_ring[i].flags = BD_FLG_TCP_UDP_SUM;
+
+	ap->rx_std_skbprd = 0;
+	atomic_set(&ap->cur_rx_bufs, 0);
+
+	set_aceaddr(&info->rx_jumbo_ctrl.rngptr,
+		    (ap->rx_ring_base_dma +
+		     (sizeof(struct rx_desc) * RX_STD_RING_ENTRIES)));
+	info->rx_jumbo_ctrl.max_len = 0;
+	info->rx_jumbo_ctrl.flags =
+	  RCB_FLG_TCP_UDP_SUM | RCB_FLG_NO_PSEUDO_HDR | ACE_RCB_VLAN_FLAG;
+
+	memset(ap->rx_jumbo_ring, 0,
+	       RX_JUMBO_RING_ENTRIES * sizeof(struct rx_desc));
+
+	for (i = 0; i < RX_JUMBO_RING_ENTRIES; i++)
+		ap->rx_jumbo_ring[i].flags = BD_FLG_TCP_UDP_SUM | BD_FLG_JUMBO;
+
+	ap->rx_jumbo_skbprd = 0;
+	atomic_set(&ap->cur_jumbo_bufs, 0);
+
+	memset(ap->rx_mini_ring, 0,
+	       RX_MINI_RING_ENTRIES * sizeof(struct rx_desc));
+
+	if (ap->version >= 2) {
+		set_aceaddr(&info->rx_mini_ctrl.rngptr,
+			    (ap->rx_ring_base_dma +
+			     (sizeof(struct rx_desc) *
+			      (RX_STD_RING_ENTRIES +
+			       RX_JUMBO_RING_ENTRIES))));
+		info->rx_mini_ctrl.max_len = ACE_MINI_SIZE;
+		info->rx_mini_ctrl.flags = 
+		  RCB_FLG_TCP_UDP_SUM|RCB_FLG_NO_PSEUDO_HDR|ACE_RCB_VLAN_FLAG;
+
+		for (i = 0; i < RX_MINI_RING_ENTRIES; i++)
+			ap->rx_mini_ring[i].flags =
+				BD_FLG_TCP_UDP_SUM | BD_FLG_MINI;
+	} else {
+		set_aceaddr(&info->rx_mini_ctrl.rngptr, 0);
+		info->rx_mini_ctrl.flags = RCB_FLG_RNG_DISABLE;
+		info->rx_mini_ctrl.max_len = 0;
+	}
+
+	ap->rx_mini_skbprd = 0;
+	atomic_set(&ap->cur_mini_bufs, 0);
+
+	set_aceaddr(&info->rx_return_ctrl.rngptr,
+		    (ap->rx_ring_base_dma +
+		     (sizeof(struct rx_desc) *
+		      (RX_STD_RING_ENTRIES +
+		       RX_JUMBO_RING_ENTRIES +
+		       RX_MINI_RING_ENTRIES))));
+	info->rx_return_ctrl.flags = 0;
+	info->rx_return_ctrl.max_len = RX_RETURN_RING_ENTRIES;
+
+	memset(ap->rx_return_ring, 0,
+	       RX_RETURN_RING_ENTRIES * sizeof(struct rx_desc));
+
+	set_aceaddr(&info->rx_ret_prd_ptr, ap->rx_ret_prd_dma);
+	*(ap->rx_ret_prd) = 0;
+
+	writel(TX_RING_BASE, &regs->WinBase);
+
+	if (ACE_IS_TIGON_I(ap)) {
+		ap->tx_ring = (struct tx_desc *) regs->Window;
+		for (i = 0; i < (TIGON_I_TX_RING_ENTRIES 
+				 * sizeof(struct tx_desc)) / sizeof(u32); i++)
+			writel(0, (void __iomem *)ap->tx_ring  + i * 4);
+
+		set_aceaddr(&info->tx_ctrl.rngptr, TX_RING_BASE);
+	} else {
+		memset(ap->tx_ring, 0,
+		       MAX_TX_RING_ENTRIES * sizeof(struct tx_desc));
+
+		set_aceaddr(&info->tx_ctrl.rngptr, ap->tx_ring_dma);
+	}
+
+	info->tx_ctrl.max_len = ACE_TX_RING_ENTRIES(ap);
+	tmp = RCB_FLG_TCP_UDP_SUM | RCB_FLG_NO_PSEUDO_HDR | ACE_RCB_VLAN_FLAG;
+
+	/*
+	 * The Tigon I does not like having the TX ring in host memory ;-(
+	 */
+	if (!ACE_IS_TIGON_I(ap))
+		tmp |= RCB_FLG_TX_HOST_RING;
+#if TX_COAL_INTS_ONLY
+	tmp |= RCB_FLG_COAL_INT_ONLY;
+#endif
+	info->tx_ctrl.flags = tmp;
+
+	set_aceaddr(&info->tx_csm_ptr, ap->tx_csm_dma);
+
+	/*
+	 * Potential item for tuning parameter
+	 */
+#if 0 /* NO */
+	writel(DMA_THRESH_16W, &regs->DmaReadCfg);
+	writel(DMA_THRESH_16W, &regs->DmaWriteCfg);
+#else
+	writel(DMA_THRESH_8W, &regs->DmaReadCfg);
+	writel(DMA_THRESH_8W, &regs->DmaWriteCfg);
+#endif
+
+	writel(0, &regs->MaskInt);
+	writel(1, &regs->IfIdx);
+#if 0
+	/*
+	 * McKinley boxes do not like us fiddling with AssistState
+	 * this early
+	 */
+	writel(1, &regs->AssistState);
+#endif
+
+	writel(DEF_STAT, &regs->TuneStatTicks);
+	writel(DEF_TRACE, &regs->TuneTrace);
+
+	ace_set_rxtx_parms(dev, 0);
+
+	if (board_idx == BOARD_IDX_OVERFLOW) {
+		printk(KERN_WARNING "%s: more than %i NICs detected, "
+		       "ignoring module parameters!\n",
+		       ap->name, ACE_MAX_MOD_PARMS);
+	} else if (board_idx >= 0) {
+		if (tx_coal_tick[board_idx])
+			writel(tx_coal_tick[board_idx],
+			       &regs->TuneTxCoalTicks);
+		if (max_tx_desc[board_idx])
+			writel(max_tx_desc[board_idx], &regs->TuneMaxTxDesc);
+
+		if (rx_coal_tick[board_idx])
+			writel(rx_coal_tick[board_idx],
+			       &regs->TuneRxCoalTicks);
+		if (max_rx_desc[board_idx])
+			writel(max_rx_desc[board_idx], &regs->TuneMaxRxDesc);
+
+		if (trace[board_idx])
+			writel(trace[board_idx], &regs->TuneTrace);
+
+		if ((tx_ratio[board_idx] > 0) && (tx_ratio[board_idx] < 64))
+			writel(tx_ratio[board_idx], &regs->TxBufRat);
+	}
+
+	/*
+	 * Default link parameters
+	 */
+	tmp = LNK_ENABLE | LNK_FULL_DUPLEX | LNK_1000MB | LNK_100MB |
+		LNK_10MB | LNK_RX_FLOW_CTL_Y | LNK_NEG_FCTL | LNK_NEGOTIATE;
+	if(ap->version >= 2)
+		tmp |= LNK_TX_FLOW_CTL_Y;
+
+	/*
+	 * Override link default parameters
+	 */
+	if ((board_idx >= 0) && link[board_idx]) {
+		int option = link[board_idx];
+
+		tmp = LNK_ENABLE;
+
+		if (option & 0x01) {
+			printk(KERN_INFO "%s: Setting half duplex link\n",
+			       ap->name);
+			tmp &= ~LNK_FULL_DUPLEX;
+		}
+		if (option & 0x02)
+			tmp &= ~LNK_NEGOTIATE;
+		if (option & 0x10)
+			tmp |= LNK_10MB;
+		if (option & 0x20)
+			tmp |= LNK_100MB;
+		if (option & 0x40)
+			tmp |= LNK_1000MB;
+		if ((option & 0x70) == 0) {
+			printk(KERN_WARNING "%s: No media speed specified, "
+			       "forcing auto negotiation\n", ap->name);
+			tmp |= LNK_NEGOTIATE | LNK_1000MB |
+				LNK_100MB | LNK_10MB;
+		}
+		if ((option & 0x100) == 0)
+			tmp |= LNK_NEG_FCTL;
+		else
+			printk(KERN_INFO "%s: Disabling flow control "
+			       "negotiation\n", ap->name);
+		if (option & 0x200)
+			tmp |= LNK_RX_FLOW_CTL_Y;
+		if ((option & 0x400) && (ap->version >= 2)) {
+			printk(KERN_INFO "%s: Enabling TX flow control\n",
+			       ap->name);
+			tmp |= LNK_TX_FLOW_CTL_Y;
+		}
+	}
+
+	ap->link = tmp;
+	writel(tmp, &regs->TuneLink);
+	if (ap->version >= 2)
+		writel(tmp, &regs->TuneFastLink);
+
+	if (ACE_IS_TIGON_I(ap))
+		writel(tigonFwStartAddr, &regs->Pc);
+	if (ap->version == 2)
+		writel(tigon2FwStartAddr, &regs->Pc);
+
+	writel(0, &regs->Mb0Lo);
+
+	/*
+	 * Set tx_csm before we start receiving interrupts, otherwise
+	 * the interrupt handler might think it is supposed to process
+	 * tx ints before we are up and running, which may cause a null
+	 * pointer access in the int handler.
+	 */
+	ap->cur_rx = 0;
+	ap->tx_prd = *(ap->tx_csm) = ap->tx_ret_csm = 0;
+
+	wmb();
+	ace_set_txprd(regs, ap, 0);
+	writel(0, &regs->RxRetCsm);
+
+	/*
+	 * Zero the stats before starting the interface
+	 */
+	memset(&ap->stats, 0, sizeof(ap->stats));
+
+       /*
+	* Enable DMA engine now.
+	* If we do this sooner, Mckinley box pukes.
+	* I assume it's because Tigon II DMA engine wants to check
+	* *something* even before the CPU is started.
+	*/
+       writel(1, &regs->AssistState);  /* enable DMA */
+
+	/*
+	 * Start the NIC CPU
+	 */
+	writel(readl(&regs->CpuCtrl) & ~(CPU_HALT|CPU_TRACE), &regs->CpuCtrl);
+	readl(&regs->CpuCtrl);
+
+	/*
+	 * Wait for the firmware to spin up - max 3 seconds.
+	 */
+	myjif = jiffies + 3 * HZ;
+	while (time_before(jiffies, myjif) && !ap->fw_running)
+		cpu_relax();
+
+	if (!ap->fw_running) {
+		printk(KERN_ERR "%s: Firmware NOT running!\n", ap->name);
+
+		ace_dump_trace(ap);
+		writel(readl(&regs->CpuCtrl) | CPU_HALT, &regs->CpuCtrl);
+		readl(&regs->CpuCtrl);
+
+		/* aman@sgi.com - account for badly behaving firmware/NIC:
+		 * - have observed that the NIC may continue to generate
+		 *   interrupts for some reason; attempt to stop it - halt
+		 *   second CPU for Tigon II cards, and also clear Mb0
+		 * - if we're a module, we'll fail to load if this was
+		 *   the only GbE card in the system => if the kernel does
+		 *   see an interrupt from the NIC, code to handle it is
+		 *   gone and OOps! - so free_irq also
+		 */
+		if (ap->version >= 2)
+			writel(readl(&regs->CpuBCtrl) | CPU_HALT,
+			       &regs->CpuBCtrl);
+		writel(0, &regs->Mb0Lo);
+		readl(&regs->Mb0Lo);
+
+		ecode = -EBUSY;
+		goto init_error;
+	}
+
+	/*
+	 * We load the ring here as there seem to be no way to tell the
+	 * firmware to wipe the ring without re-initializing it.
+	 */
+	if (!test_and_set_bit(0, &ap->std_refill_busy))
+		ace_load_std_rx_ring(ap, RX_RING_SIZE);
+	else
+		printk(KERN_ERR "%s: Someone is busy refilling the RX ring\n",
+		       ap->name);
+	if (ap->version >= 2) {
+		if (!test_and_set_bit(0, &ap->mini_refill_busy))
+			ace_load_mini_rx_ring(ap, RX_MINI_SIZE);
+		else
+			printk(KERN_ERR "%s: Someone is busy refilling "
+			       "the RX mini ring\n", ap->name);
+	}
+	return 0;
+
+ init_error:
+	ace_init_cleanup(dev);
+	return ecode;
+}
+
+
+static void ace_set_rxtx_parms(struct net_device *dev, int jumbo)
+{
+	struct ace_private *ap = netdev_priv(dev);
+	struct ace_regs __iomem *regs = ap->regs;
+	int board_idx = ap->board_idx;
+
+	if (board_idx >= 0) {
+		if (!jumbo) {
+			if (!tx_coal_tick[board_idx])
+				writel(DEF_TX_COAL, &regs->TuneTxCoalTicks);
+			if (!max_tx_desc[board_idx])
+				writel(DEF_TX_MAX_DESC, &regs->TuneMaxTxDesc);
+			if (!rx_coal_tick[board_idx])
+				writel(DEF_RX_COAL, &regs->TuneRxCoalTicks);
+			if (!max_rx_desc[board_idx])
+				writel(DEF_RX_MAX_DESC, &regs->TuneMaxRxDesc);
+			if (!tx_ratio[board_idx])
+				writel(DEF_TX_RATIO, &regs->TxBufRat);
+		} else {
+			if (!tx_coal_tick[board_idx])
+				writel(DEF_JUMBO_TX_COAL,
+				       &regs->TuneTxCoalTicks);
+			if (!max_tx_desc[board_idx])
+				writel(DEF_JUMBO_TX_MAX_DESC,
+				       &regs->TuneMaxTxDesc);
+			if (!rx_coal_tick[board_idx])
+				writel(DEF_JUMBO_RX_COAL,
+				       &regs->TuneRxCoalTicks);
+			if (!max_rx_desc[board_idx])
+				writel(DEF_JUMBO_RX_MAX_DESC,
+				       &regs->TuneMaxRxDesc);
+			if (!tx_ratio[board_idx])
+				writel(DEF_JUMBO_TX_RATIO, &regs->TxBufRat);
+		}
+	}
+}
+
+
+static void ace_watchdog(struct net_device *data)
+{
+	struct net_device *dev = data;
+	struct ace_private *ap = netdev_priv(dev);
+	struct ace_regs __iomem *regs = ap->regs;
+
+	/*
+	 * We haven't received a stats update event for more than 2.5
+	 * seconds and there is data in the transmit queue, thus we
+	 * asume the card is stuck.
+	 */
+	if (*ap->tx_csm != ap->tx_ret_csm) {
+		printk(KERN_WARNING "%s: Transmitter is stuck, %08x\n",
+		       dev->name, (unsigned int)readl(&regs->HostCtrl));
+		/* This can happen due to ieee flow control. */
+	} else {
+		printk(KERN_DEBUG "%s: BUG... transmitter died. Kicking it.\n",
+		       dev->name);
+#if 0
+		netif_wake_queue(dev);
+#endif
+	}
+}
+
+
+static void ace_tasklet(unsigned long dev)
+{
+	struct ace_private *ap = netdev_priv((struct net_device *)dev);
+	int cur_size;
+
+	cur_size = atomic_read(&ap->cur_rx_bufs);
+	if ((cur_size < RX_LOW_STD_THRES) &&
+	    !test_and_set_bit(0, &ap->std_refill_busy)) {
+#ifdef DEBUG
+		printk("refilling buffers (current %i)\n", cur_size);
+#endif
+		ace_load_std_rx_ring(ap, RX_RING_SIZE - cur_size);
+	}
+
+	if (ap->version >= 2) {
+		cur_size = atomic_read(&ap->cur_mini_bufs);
+		if ((cur_size < RX_LOW_MINI_THRES) &&
+		    !test_and_set_bit(0, &ap->mini_refill_busy)) {
+#ifdef DEBUG
+			printk("refilling mini buffers (current %i)\n",
+			       cur_size);
+#endif
+			ace_load_mini_rx_ring(ap, RX_MINI_SIZE - cur_size);
+		}
+	}
+
+	cur_size = atomic_read(&ap->cur_jumbo_bufs);
+	if (ap->jumbo && (cur_size < RX_LOW_JUMBO_THRES) &&
+	    !test_and_set_bit(0, &ap->jumbo_refill_busy)) {
+#ifdef DEBUG
+		printk("refilling jumbo buffers (current %i)\n", cur_size);
+#endif
+		ace_load_jumbo_rx_ring(ap, RX_JUMBO_SIZE - cur_size);
+	}
+	ap->tasklet_pending = 0;
+}
+
+
+/*
+ * Copy the contents of the NIC's trace buffer to kernel memory.
+ */
+static void ace_dump_trace(struct ace_private *ap)
+{
+#if 0
+	if (!ap->trace_buf)
+		if (!(ap->trace_buf = kmalloc(ACE_TRACE_SIZE, GFP_KERNEL)))
+		    return;
+#endif
+}
+
+
+/*
+ * Load the standard rx ring.
+ *
+ * Loading rings is safe without holding the spin lock since this is
+ * done only before the device is enabled, thus no interrupts are
+ * generated and by the interrupt handler/tasklet handler.
+ */
+static void ace_load_std_rx_ring(struct ace_private *ap, int nr_bufs)
+{
+	struct ace_regs __iomem *regs = ap->regs;
+	short i, idx;
+	
+
+	prefetchw(&ap->cur_rx_bufs);
+
+	idx = ap->rx_std_skbprd;
+
+	for (i = 0; i < nr_bufs; i++) {
+		struct sk_buff *skb;
+		struct rx_desc *rd;
+		dma_addr_t mapping;
+
+		skb = alloc_skb(ACE_STD_BUFSIZE + NET_IP_ALIGN, GFP_ATOMIC);
+		if (!skb)
+			break;
+
+		skb_reserve(skb, NET_IP_ALIGN);
+		mapping = pci_map_page(ap->pdev, virt_to_page(skb->data),
+				       offset_in_page(skb->data),
+				       ACE_STD_BUFSIZE,
+				       PCI_DMA_FROMDEVICE);
+		ap->skb->rx_std_skbuff[idx].skb = skb;
+		pci_unmap_addr_set(&ap->skb->rx_std_skbuff[idx],
+				   mapping, mapping);
+
+		rd = &ap->rx_std_ring[idx];
+		set_aceaddr(&rd->addr, mapping);
+		rd->size = ACE_STD_BUFSIZE;
+		rd->idx = idx;
+		idx = (idx + 1) % RX_STD_RING_ENTRIES;
+	}
+
+	if (!i)
+		goto error_out;
+
+	atomic_add(i, &ap->cur_rx_bufs);
+	ap->rx_std_skbprd = idx;
+
+	if (ACE_IS_TIGON_I(ap)) {
+		struct cmd cmd;
+		cmd.evt = C_SET_RX_PRD_IDX;
+		cmd.code = 0;
+		cmd.idx = ap->rx_std_skbprd;
+		ace_issue_cmd(regs, &cmd);
+	} else {
+		writel(idx, &regs->RxStdPrd);
+		wmb();
+	}
+
+ out:
+	clear_bit(0, &ap->std_refill_busy);
+	return;
+
+ error_out:
+	printk(KERN_INFO "Out of memory when allocating "
+	       "standard receive buffers\n");
+	goto out;
+}
+
+
+static void ace_load_mini_rx_ring(struct ace_private *ap, int nr_bufs)
+{
+	struct ace_regs __iomem *regs = ap->regs;
+	short i, idx;
+
+	prefetchw(&ap->cur_mini_bufs);
+
+	idx = ap->rx_mini_skbprd;
+	for (i = 0; i < nr_bufs; i++) {
+		struct sk_buff *skb;
+		struct rx_desc *rd;
+		dma_addr_t mapping;
+
+		skb = alloc_skb(ACE_MINI_BUFSIZE + NET_IP_ALIGN, GFP_ATOMIC);
+		if (!skb)
+			break;
+
+		skb_reserve(skb, NET_IP_ALIGN);
+		mapping = pci_map_page(ap->pdev, virt_to_page(skb->data),
+				       offset_in_page(skb->data),
+				       ACE_MINI_BUFSIZE,
+				       PCI_DMA_FROMDEVICE);
+		ap->skb->rx_mini_skbuff[idx].skb = skb;
+		pci_unmap_addr_set(&ap->skb->rx_mini_skbuff[idx],
+				   mapping, mapping);
+
+		rd = &ap->rx_mini_ring[idx];
+		set_aceaddr(&rd->addr, mapping);
+		rd->size = ACE_MINI_BUFSIZE;
+		rd->idx = idx;
+		idx = (idx + 1) % RX_MINI_RING_ENTRIES;
+	}
+
+	if (!i)
+		goto error_out;
+
+	atomic_add(i, &ap->cur_mini_bufs);
+
+	ap->rx_mini_skbprd = idx;
+
+	writel(idx, &regs->RxMiniPrd);
+	wmb();
+
+ out:
+	clear_bit(0, &ap->mini_refill_busy);
+	return;
+ error_out:
+	printk(KERN_INFO "Out of memory when allocating "
+	       "mini receive buffers\n");
+	goto out;
+}
+
+
+/*
+ * Load the jumbo rx ring, this may happen at any time if the MTU
+ * is changed to a value > 1500.
+ */
+static void ace_load_jumbo_rx_ring(struct ace_private *ap, int nr_bufs)
+{
+	struct ace_regs __iomem *regs = ap->regs;
+	short i, idx;
+
+	idx = ap->rx_jumbo_skbprd;
+
+	for (i = 0; i < nr_bufs; i++) {
+		struct sk_buff *skb;
+		struct rx_desc *rd;
+		dma_addr_t mapping;
+
+		skb = alloc_skb(ACE_JUMBO_BUFSIZE + NET_IP_ALIGN, GFP_ATOMIC);
+		if (!skb)
+			break;
+
+		skb_reserve(skb, NET_IP_ALIGN);
+		mapping = pci_map_page(ap->pdev, virt_to_page(skb->data),
+				       offset_in_page(skb->data),
+				       ACE_JUMBO_BUFSIZE,
+				       PCI_DMA_FROMDEVICE);
+		ap->skb->rx_jumbo_skbuff[idx].skb = skb;
+		pci_unmap_addr_set(&ap->skb->rx_jumbo_skbuff[idx],
+				   mapping, mapping);
+
+		rd = &ap->rx_jumbo_ring[idx];
+		set_aceaddr(&rd->addr, mapping);
+		rd->size = ACE_JUMBO_BUFSIZE;
+		rd->idx = idx;
+		idx = (idx + 1) % RX_JUMBO_RING_ENTRIES;
+	}
+
+	if (!i)
+		goto error_out;
+
+	atomic_add(i, &ap->cur_jumbo_bufs);
+	ap->rx_jumbo_skbprd = idx;
+
+	if (ACE_IS_TIGON_I(ap)) {
+		struct cmd cmd;
+		cmd.evt = C_SET_RX_JUMBO_PRD_IDX;
+		cmd.code = 0;
+		cmd.idx = ap->rx_jumbo_skbprd;
+		ace_issue_cmd(regs, &cmd);
+	} else {
+		writel(idx, &regs->RxJumboPrd);
+		wmb();
+	}
+
+ out:
+	clear_bit(0, &ap->jumbo_refill_busy);
+	return;
+ error_out:
+	if (net_ratelimit())
+		printk(KERN_INFO "Out of memory when allocating "
+		       "jumbo receive buffers\n");
+	goto out;
+}
+
+
+/*
+ * All events are considered to be slow (RX/TX ints do not generate
+ * events) and are handled here, outside the main interrupt handler,
+ * to reduce the size of the handler.
+ */
+static u32 ace_handle_event(struct net_device *dev, u32 evtcsm, u32 evtprd)
+{
+	struct ace_private *ap;
+
+	ap = netdev_priv(dev);
+
+	while (evtcsm != evtprd) {
+		switch (ap->evt_ring[evtcsm].evt) {
+		case E_FW_RUNNING:
+			printk(KERN_INFO "%s: Firmware up and running\n",
+			       ap->name);
+			ap->fw_running = 1;
+			wmb();
+			break;
+		case E_STATS_UPDATED:
+			break;
+		case E_LNK_STATE:
+		{
+			u16 code = ap->evt_ring[evtcsm].code;
+			switch (code) {
+			case E_C_LINK_UP:
+			{
+				u32 state = readl(&ap->regs->GigLnkState);
+				printk(KERN_WARNING "%s: Optical link UP "
+				       "(%s Duplex, Flow Control: %s%s)\n",
+				       ap->name,
+				       state & LNK_FULL_DUPLEX ? "Full":"Half",
+				       state & LNK_TX_FLOW_CTL_Y ? "TX " : "",
+				       state & LNK_RX_FLOW_CTL_Y ? "RX" : "");
+				break;
+			}
+			case E_C_LINK_DOWN:
+				printk(KERN_WARNING "%s: Optical link DOWN\n",
+				       ap->name);
+				break;
+			case E_C_LINK_10_100:
+				printk(KERN_WARNING "%s: 10/100BaseT link "
+				       "UP\n", ap->name);
+				break;
+			default:
+				printk(KERN_ERR "%s: Unknown optical link "
+				       "state %02x\n", ap->name, code);
+			}
+			break;
+		}
+		case E_ERROR:
+			switch(ap->evt_ring[evtcsm].code) {
+			case E_C_ERR_INVAL_CMD:
+				printk(KERN_ERR "%s: invalid command error\n",
+				       ap->name);
+				break;
+			case E_C_ERR_UNIMP_CMD:
+				printk(KERN_ERR "%s: unimplemented command "
+				       "error\n", ap->name);
+				break;
+			case E_C_ERR_BAD_CFG:
+				printk(KERN_ERR "%s: bad config error\n",
+				       ap->name);
+				break;
+			default:
+				printk(KERN_ERR "%s: unknown error %02x\n",
+				       ap->name, ap->evt_ring[evtcsm].code);
+			}
+			break;
+		case E_RESET_JUMBO_RNG:
+		{
+			int i;
+			for (i = 0; i < RX_JUMBO_RING_ENTRIES; i++) {
+				if (ap->skb->rx_jumbo_skbuff[i].skb) {
+					ap->rx_jumbo_ring[i].size = 0;
+					set_aceaddr(&ap->rx_jumbo_ring[i].addr, 0);
+					dev_kfree_skb(ap->skb->rx_jumbo_skbuff[i].skb);
+					ap->skb->rx_jumbo_skbuff[i].skb = NULL;
+				}
+			}
+
+ 			if (ACE_IS_TIGON_I(ap)) {
+ 				struct cmd cmd;
+ 				cmd.evt = C_SET_RX_JUMBO_PRD_IDX;
+ 				cmd.code = 0;
+ 				cmd.idx = 0;
+ 				ace_issue_cmd(ap->regs, &cmd);
+ 			} else {
+ 				writel(0, &((ap->regs)->RxJumboPrd));
+ 				wmb();
+ 			}
+
+			ap->jumbo = 0;
+			ap->rx_jumbo_skbprd = 0;
+			printk(KERN_INFO "%s: Jumbo ring flushed\n",
+			       ap->name);
+			clear_bit(0, &ap->jumbo_refill_busy);
+			break;
+		}
+		default:
+			printk(KERN_ERR "%s: Unhandled event 0x%02x\n",
+			       ap->name, ap->evt_ring[evtcsm].evt);
+		}
+		evtcsm = (evtcsm + 1) % EVT_RING_ENTRIES;
+	}
+
+	return evtcsm;
+}
+
+
+static void ace_rx_int(struct net_device *dev, u32 rxretprd, u32 rxretcsm)
+{
+	struct ace_private *ap = netdev_priv(dev);
+	u32 idx;
+	int mini_count = 0, std_count = 0;
+
+	idx = rxretcsm;
+
+	prefetchw(&ap->cur_rx_bufs);
+	prefetchw(&ap->cur_mini_bufs);
+	
+	while (idx != rxretprd) {
+		struct ring_info *rip;
+		struct sk_buff *skb;
+		struct rx_desc *rxdesc, *retdesc;
+		u32 skbidx;
+		int bd_flags, desc_type, mapsize;
+		u16 csum;
+
+
+		/* make sure the rx descriptor isn't read before rxretprd */
+		if (idx == rxretcsm) 
+			rmb();
+
+		retdesc = &ap->rx_return_ring[idx];
+		skbidx = retdesc->idx;
+		bd_flags = retdesc->flags;
+		desc_type = bd_flags & (BD_FLG_JUMBO | BD_FLG_MINI);
+
+		switch(desc_type) {
+			/*
+			 * Normal frames do not have any flags set
+			 *
+			 * Mini and normal frames arrive frequently,
+			 * so use a local counter to avoid doing
+			 * atomic operations for each packet arriving.
+			 */
+		case 0:
+			rip = &ap->skb->rx_std_skbuff[skbidx];
+			mapsize = ACE_STD_BUFSIZE;
+			rxdesc = &ap->rx_std_ring[skbidx];
+			std_count++;
+			break;
+		case BD_FLG_JUMBO:
+			rip = &ap->skb->rx_jumbo_skbuff[skbidx];
+			mapsize = ACE_JUMBO_BUFSIZE;
+			rxdesc = &ap->rx_jumbo_ring[skbidx];
+			atomic_dec(&ap->cur_jumbo_bufs);
+			break;
+		case BD_FLG_MINI:
+			rip = &ap->skb->rx_mini_skbuff[skbidx];
+			mapsize = ACE_MINI_BUFSIZE;
+			rxdesc = &ap->rx_mini_ring[skbidx];
+			mini_count++; 
+			break;
+		default:
+			printk(KERN_INFO "%s: unknown frame type (0x%02x) "
+			       "returned by NIC\n", dev->name,
+			       retdesc->flags);
+			goto error;
+		}
+
+		skb = rip->skb;
+		rip->skb = NULL;
+		pci_unmap_page(ap->pdev,
+			       pci_unmap_addr(rip, mapping),
+			       mapsize,
+			       PCI_DMA_FROMDEVICE);
+		skb_put(skb, retdesc->size);
+
+		/*
+		 * Fly baby, fly!
+		 */
+		csum = retdesc->tcp_udp_csum;
+
+		skb->dev = dev;
+		skb->protocol = eth_type_trans(skb, dev);
+
+		/*
+		 * Instead of forcing the poor tigon mips cpu to calculate
+		 * pseudo hdr checksum, we do this ourselves.
+		 */
+		if (bd_flags & BD_FLG_TCP_UDP_SUM) {
+			skb->csum = htons(csum);
+			skb->ip_summed = CHECKSUM_HW;
+		} else {
+			skb->ip_summed = CHECKSUM_NONE;
+		}
+
+		/* send it up */
+#if ACENIC_DO_VLAN
+		if (ap->vlgrp && (bd_flags & BD_FLG_VLAN_TAG)) {
+			vlan_hwaccel_rx(skb, ap->vlgrp, retdesc->vlan);
+		} else
+#endif
+			netif_rx(skb);
+
+		dev->last_rx = jiffies;
+		ap->stats.rx_packets++;
+		ap->stats.rx_bytes += retdesc->size;
+
+		idx = (idx + 1) % RX_RETURN_RING_ENTRIES;
+	}
+
+	atomic_sub(std_count, &ap->cur_rx_bufs);
+	if (!ACE_IS_TIGON_I(ap))
+		atomic_sub(mini_count, &ap->cur_mini_bufs);
+
+ out:
+	/*
+	 * According to the documentation RxRetCsm is obsolete with
+	 * the 12.3.x Firmware - my Tigon I NICs seem to disagree!
+	 */
+	if (ACE_IS_TIGON_I(ap)) {
+		writel(idx, &ap->regs->RxRetCsm);
+	}
+	ap->cur_rx = idx;
+
+	return;
+ error:
+	idx = rxretprd;
+	goto out;
+}
+
+
+static inline void ace_tx_int(struct net_device *dev,
+			      u32 txcsm, u32 idx)
+{
+	struct ace_private *ap = netdev_priv(dev);
+
+	do {
+		struct sk_buff *skb;
+		dma_addr_t mapping;
+		struct tx_ring_info *info;
+
+		info = ap->skb->tx_skbuff + idx;
+		skb = info->skb;
+		mapping = pci_unmap_addr(info, mapping);
+
+		if (mapping) {
+			pci_unmap_page(ap->pdev, mapping,
+				       pci_unmap_len(info, maplen),
+				       PCI_DMA_TODEVICE);
+			pci_unmap_addr_set(info, mapping, 0);
+		}
+
+		if (skb) {
+			ap->stats.tx_packets++;
+			ap->stats.tx_bytes += skb->len;
+			dev_kfree_skb_irq(skb);
+			info->skb = NULL;
+		}
+
+		idx = (idx + 1) % ACE_TX_RING_ENTRIES(ap);
+	} while (idx != txcsm);
+
+	if (netif_queue_stopped(dev))
+		netif_wake_queue(dev);
+
+	wmb();
+	ap->tx_ret_csm = txcsm;
+
+	/* So... tx_ret_csm is advanced _after_ check for device wakeup.
+	 *
+	 * We could try to make it before. In this case we would get
+	 * the following race condition: hard_start_xmit on other cpu
+	 * enters after we advanced tx_ret_csm and fills space,
+	 * which we have just freed, so that we make illegal device wakeup.
+	 * There is no good way to workaround this (at entry
+	 * to ace_start_xmit detects this condition and prevents
+	 * ring corruption, but it is not a good workaround.)
+	 *
+	 * When tx_ret_csm is advanced after, we wake up device _only_
+	 * if we really have some space in ring (though the core doing
+	 * hard_start_xmit can see full ring for some period and has to
+	 * synchronize.) Superb.
+	 * BUT! We get another subtle race condition. hard_start_xmit
+	 * may think that ring is full between wakeup and advancing
+	 * tx_ret_csm and will stop device instantly! It is not so bad.
+	 * We are guaranteed that there is something in ring, so that
+	 * the next irq will resume transmission. To speedup this we could
+	 * mark descriptor, which closes ring with BD_FLG_COAL_NOW
+	 * (see ace_start_xmit).
+	 *
+	 * Well, this dilemma exists in all lock-free devices.
+	 * We, following scheme used in drivers by Donald Becker,
+	 * select the least dangerous.
+	 *							--ANK
+	 */
+}
+
+
+static irqreturn_t ace_interrupt(int irq, void *dev_id, struct pt_regs *ptregs)
+{
+	struct net_device *dev = (struct net_device *)dev_id;
+	struct ace_private *ap = netdev_priv(dev);
+	struct ace_regs __iomem *regs = ap->regs;
+	u32 idx;
+	u32 txcsm, rxretcsm, rxretprd;
+	u32 evtcsm, evtprd;
+
+	/*
+	 * In case of PCI shared interrupts or spurious interrupts,
+	 * we want to make sure it is actually our interrupt before
+	 * spending any time in here.
+	 */
+	if (!(readl(&regs->HostCtrl) & IN_INT))
+		return IRQ_NONE;
+
+	/*
+	 * ACK intr now. Otherwise we will lose updates to rx_ret_prd,
+	 * which happened _after_ rxretprd = *ap->rx_ret_prd; but before
+	 * writel(0, &regs->Mb0Lo).
+	 *
+	 * "IRQ avoidance" recommended in docs applies to IRQs served
+	 * threads and it is wrong even for that case.
+	 */
+	writel(0, &regs->Mb0Lo);
+	readl(&regs->Mb0Lo);
+
+	/*
+	 * There is no conflict between transmit handling in
+	 * start_xmit and receive processing, thus there is no reason
+	 * to take a spin lock for RX handling. Wait until we start
+	 * working on the other stuff - hey we don't need a spin lock
+	 * anymore.
+	 */
+	rxretprd = *ap->rx_ret_prd;
+	rxretcsm = ap->cur_rx;
+
+	if (rxretprd != rxretcsm)
+		ace_rx_int(dev, rxretprd, rxretcsm);
+
+	txcsm = *ap->tx_csm;
+	idx = ap->tx_ret_csm;
+
+	if (txcsm != idx) {
+		/*
+		 * If each skb takes only one descriptor this check degenerates
+		 * to identity, because new space has just been opened.
+		 * But if skbs are fragmented we must check that this index
+		 * update releases enough of space, otherwise we just
+		 * wait for device to make more work.
+		 */
+		if (!tx_ring_full(ap, txcsm, ap->tx_prd))
+			ace_tx_int(dev, txcsm, idx);
+	}
+
+	evtcsm = readl(&regs->EvtCsm);
+	evtprd = *ap->evt_prd;
+
+	if (evtcsm != evtprd) {
+		evtcsm = ace_handle_event(dev, evtcsm, evtprd);
+		writel(evtcsm, &regs->EvtCsm);
+	}
+
+	/*
+	 * This has to go last in the interrupt handler and run with
+	 * the spin lock released ... what lock?
+	 */
+	if (netif_running(dev)) {
+		int cur_size;
+		int run_tasklet = 0;
+
+		cur_size = atomic_read(&ap->cur_rx_bufs);
+		if (cur_size < RX_LOW_STD_THRES) {
+			if ((cur_size < RX_PANIC_STD_THRES) &&
+			    !test_and_set_bit(0, &ap->std_refill_busy)) {
+#ifdef DEBUG
+				printk("low on std buffers %i\n", cur_size);
+#endif
+				ace_load_std_rx_ring(ap,
+						     RX_RING_SIZE - cur_size);
+			} else
+				run_tasklet = 1;
+		}
+
+		if (!ACE_IS_TIGON_I(ap)) {
+			cur_size = atomic_read(&ap->cur_mini_bufs);
+			if (cur_size < RX_LOW_MINI_THRES) {
+				if ((cur_size < RX_PANIC_MINI_THRES) &&
+				    !test_and_set_bit(0,
+						      &ap->mini_refill_busy)) {
+#ifdef DEBUG
+					printk("low on mini buffers %i\n",
+					       cur_size);
+#endif
+					ace_load_mini_rx_ring(ap, RX_MINI_SIZE - cur_size);
+				} else
+					run_tasklet = 1;
+			}
+		}
+
+		if (ap->jumbo) {
+			cur_size = atomic_read(&ap->cur_jumbo_bufs);
+			if (cur_size < RX_LOW_JUMBO_THRES) {
+				if ((cur_size < RX_PANIC_JUMBO_THRES) &&
+				    !test_and_set_bit(0,
+						      &ap->jumbo_refill_busy)){
+#ifdef DEBUG
+					printk("low on jumbo buffers %i\n",
+					       cur_size);
+#endif
+					ace_load_jumbo_rx_ring(ap, RX_JUMBO_SIZE - cur_size);
+				} else
+					run_tasklet = 1;
+			}
+		}
+		if (run_tasklet && !ap->tasklet_pending) {
+			ap->tasklet_pending = 1;
+			tasklet_schedule(&ap->ace_tasklet);
+		}
+	}
+
+	return IRQ_HANDLED;
+}
+
+
+#if ACENIC_DO_VLAN
+static void ace_vlan_rx_register(struct net_device *dev, struct vlan_group *grp)
+{
+	struct ace_private *ap = netdev_priv(dev);
+	unsigned long flags;
+
+	local_irq_save(flags);
+	ace_mask_irq(dev);
+
+	ap->vlgrp = grp;
+
+	ace_unmask_irq(dev);
+	local_irq_restore(flags);
+}
+
+
+static void ace_vlan_rx_kill_vid(struct net_device *dev, unsigned short vid)
+{
+	struct ace_private *ap = netdev_priv(dev);
+	unsigned long flags;
+
+	local_irq_save(flags);
+	ace_mask_irq(dev);
+
+	if (ap->vlgrp)
+		ap->vlgrp->vlan_devices[vid] = NULL;
+
+	ace_unmask_irq(dev);
+	local_irq_restore(flags);
+}
+#endif /* ACENIC_DO_VLAN */
+
+
+static int ace_open(struct net_device *dev)
+{
+	struct ace_private *ap = netdev_priv(dev);
+	struct ace_regs __iomem *regs = ap->regs;
+	struct cmd cmd;
+
+	if (!(ap->fw_running)) {
+		printk(KERN_WARNING "%s: Firmware not running!\n", dev->name);
+		return -EBUSY;
+	}
+
+	writel(dev->mtu + ETH_HLEN + 4, &regs->IfMtu);
+
+	cmd.evt = C_CLEAR_STATS;
+	cmd.code = 0;
+	cmd.idx = 0;
+	ace_issue_cmd(regs, &cmd);
+
+	cmd.evt = C_HOST_STATE;
+	cmd.code = C_C_STACK_UP;
+	cmd.idx = 0;
+	ace_issue_cmd(regs, &cmd);
+
+	if (ap->jumbo &&
+	    !test_and_set_bit(0, &ap->jumbo_refill_busy))
+		ace_load_jumbo_rx_ring(ap, RX_JUMBO_SIZE);
+
+	if (dev->flags & IFF_PROMISC) {
+		cmd.evt = C_SET_PROMISC_MODE;
+		cmd.code = C_C_PROMISC_ENABLE;
+		cmd.idx = 0;
+		ace_issue_cmd(regs, &cmd);
+
+		ap->promisc = 1;
+	}else
+		ap->promisc = 0;
+	ap->mcast_all = 0;
+
+#if 0
+	cmd.evt = C_LNK_NEGOTIATION;
+	cmd.code = 0;
+	cmd.idx = 0;
+	ace_issue_cmd(regs, &cmd);
+#endif
+
+	netif_start_queue(dev);
+
+	/*
+	 * Setup the bottom half rx ring refill handler
+	 */
+	tasklet_init(&ap->ace_tasklet, ace_tasklet, (unsigned long)dev);
+	return 0;
+}
+
+
+static int ace_close(struct net_device *dev)
+{
+	struct ace_private *ap = netdev_priv(dev);
+	struct ace_regs __iomem *regs = ap->regs;
+	struct cmd cmd;
+	unsigned long flags;
+	short i;
+
+	/*
+	 * Without (or before) releasing irq and stopping hardware, this
+	 * is an absolute non-sense, by the way. It will be reset instantly
+	 * by the first irq.
+	 */
+	netif_stop_queue(dev);
+
+	
+	if (ap->promisc) {
+		cmd.evt = C_SET_PROMISC_MODE;
+		cmd.code = C_C_PROMISC_DISABLE;
+		cmd.idx = 0;
+		ace_issue_cmd(regs, &cmd);
+		ap->promisc = 0;
+	}
+
+	cmd.evt = C_HOST_STATE;
+	cmd.code = C_C_STACK_DOWN;
+	cmd.idx = 0;
+	ace_issue_cmd(regs, &cmd);
+
+	tasklet_kill(&ap->ace_tasklet);
+
+	/*
+	 * Make sure one CPU is not processing packets while
+	 * buffers are being released by another.
+	 */
+
+	local_irq_save(flags);
+	ace_mask_irq(dev);
+
+	for (i = 0; i < ACE_TX_RING_ENTRIES(ap); i++) {
+		struct sk_buff *skb;
+		dma_addr_t mapping;
+		struct tx_ring_info *info;
+
+		info = ap->skb->tx_skbuff + i;
+		skb = info->skb;
+		mapping = pci_unmap_addr(info, mapping);
+
+		if (mapping) {
+			if (ACE_IS_TIGON_I(ap)) {
+				struct tx_desc __iomem *tx 
+					= (struct tx_desc __iomem *) &ap->tx_ring[i];
+				writel(0, &tx->addr.addrhi);
+				writel(0, &tx->addr.addrlo);
+				writel(0, &tx->flagsize);
+			} else
+				memset(ap->tx_ring + i, 0,
+				       sizeof(struct tx_desc));
+			pci_unmap_page(ap->pdev, mapping,
+				       pci_unmap_len(info, maplen),
+				       PCI_DMA_TODEVICE);
+			pci_unmap_addr_set(info, mapping, 0);
+		}
+		if (skb) {
+			dev_kfree_skb(skb);
+			info->skb = NULL;
+		}
+	}
+
+	if (ap->jumbo) {
+		cmd.evt = C_RESET_JUMBO_RNG;
+		cmd.code = 0;
+		cmd.idx = 0;
+		ace_issue_cmd(regs, &cmd);
+	}
+
+	ace_unmask_irq(dev);
+	local_irq_restore(flags);
+
+	return 0;
+}
+
+
+static inline dma_addr_t
+ace_map_tx_skb(struct ace_private *ap, struct sk_buff *skb,
+	       struct sk_buff *tail, u32 idx)
+{
+	dma_addr_t mapping;
+	struct tx_ring_info *info;
+
+	mapping = pci_map_page(ap->pdev, virt_to_page(skb->data),
+			       offset_in_page(skb->data),
+			       skb->len, PCI_DMA_TODEVICE);
+
+	info = ap->skb->tx_skbuff + idx;
+	info->skb = tail;
+	pci_unmap_addr_set(info, mapping, mapping);
+	pci_unmap_len_set(info, maplen, skb->len);
+	return mapping;
+}
+
+
+static inline void
+ace_load_tx_bd(struct ace_private *ap, struct tx_desc *desc, u64 addr,
+	       u32 flagsize, u32 vlan_tag)
+{
+#if !USE_TX_COAL_NOW
+	flagsize &= ~BD_FLG_COAL_NOW;
+#endif
+
+	if (ACE_IS_TIGON_I(ap)) {
+		struct tx_desc __iomem *io = (struct tx_desc __iomem *) desc;
+		writel(addr >> 32, &io->addr.addrhi);
+		writel(addr & 0xffffffff, &io->addr.addrlo);
+		writel(flagsize, &io->flagsize);
+#if ACENIC_DO_VLAN
+		writel(vlan_tag, &io->vlanres);
+#endif
+	} else {
+		desc->addr.addrhi = addr >> 32;
+		desc->addr.addrlo = addr;
+		desc->flagsize = flagsize;
+#if ACENIC_DO_VLAN
+		desc->vlanres = vlan_tag;
+#endif
+	}
+}
+
+
+static int ace_start_xmit(struct sk_buff *skb, struct net_device *dev)
+{
+	struct ace_private *ap = netdev_priv(dev);
+	struct ace_regs __iomem *regs = ap->regs;
+	struct tx_desc *desc;
+	u32 idx, flagsize;
+	unsigned long maxjiff = jiffies + 3*HZ;
+
+restart:
+	idx = ap->tx_prd;
+
+	if (tx_ring_full(ap, ap->tx_ret_csm, idx))
+		goto overflow;
+
+	if (!skb_shinfo(skb)->nr_frags)	{
+		dma_addr_t mapping;
+		u32 vlan_tag = 0;
+
+		mapping = ace_map_tx_skb(ap, skb, skb, idx);
+		flagsize = (skb->len << 16) | (BD_FLG_END);
+		if (skb->ip_summed == CHECKSUM_HW)
+			flagsize |= BD_FLG_TCP_UDP_SUM;
+#if ACENIC_DO_VLAN
+		if (vlan_tx_tag_present(skb)) {
+			flagsize |= BD_FLG_VLAN_TAG;
+			vlan_tag = vlan_tx_tag_get(skb);
+		}
+#endif
+		desc = ap->tx_ring + idx;
+		idx = (idx + 1) % ACE_TX_RING_ENTRIES(ap);
+
+		/* Look at ace_tx_int for explanations. */
+		if (tx_ring_full(ap, ap->tx_ret_csm, idx))
+			flagsize |= BD_FLG_COAL_NOW;
+
+		ace_load_tx_bd(ap, desc, mapping, flagsize, vlan_tag);
+	} else {
+		dma_addr_t mapping;
+		u32 vlan_tag = 0;
+		int i, len = 0;
+
+		mapping = ace_map_tx_skb(ap, skb, NULL, idx);
+		flagsize = (skb_headlen(skb) << 16);
+		if (skb->ip_summed == CHECKSUM_HW)
+			flagsize |= BD_FLG_TCP_UDP_SUM;
+#if ACENIC_DO_VLAN
+		if (vlan_tx_tag_present(skb)) {
+			flagsize |= BD_FLG_VLAN_TAG;
+			vlan_tag = vlan_tx_tag_get(skb);
+		}
+#endif
+
+		ace_load_tx_bd(ap, ap->tx_ring + idx, mapping, flagsize, vlan_tag);
+
+		idx = (idx + 1) % ACE_TX_RING_ENTRIES(ap);
+
+		for (i = 0; i < skb_shinfo(skb)->nr_frags; i++) {
+			skb_frag_t *frag = &skb_shinfo(skb)->frags[i];
+			struct tx_ring_info *info;
+
+			len += frag->size;
+			info = ap->skb->tx_skbuff + idx;
+			desc = ap->tx_ring + idx;
+
+			mapping = pci_map_page(ap->pdev, frag->page,
+					       frag->page_offset, frag->size,
+					       PCI_DMA_TODEVICE);
+
+			flagsize = (frag->size << 16);
+			if (skb->ip_summed == CHECKSUM_HW)
+				flagsize |= BD_FLG_TCP_UDP_SUM;
+			idx = (idx + 1) % ACE_TX_RING_ENTRIES(ap);
+
+			if (i == skb_shinfo(skb)->nr_frags - 1) {
+				flagsize |= BD_FLG_END;
+				if (tx_ring_full(ap, ap->tx_ret_csm, idx))
+					flagsize |= BD_FLG_COAL_NOW;
+
+				/*
+				 * Only the last fragment frees
+				 * the skb!
+				 */
+				info->skb = skb;
+			} else {
+				info->skb = NULL;
+			}
+			pci_unmap_addr_set(info, mapping, mapping);
+			pci_unmap_len_set(info, maplen, frag->size);
+			ace_load_tx_bd(ap, desc, mapping, flagsize, vlan_tag);
+		}
+	}
+
+ 	wmb();
+ 	ap->tx_prd = idx;
+ 	ace_set_txprd(regs, ap, idx);
+
+	if (flagsize & BD_FLG_COAL_NOW) {
+		netif_stop_queue(dev);
+
+		/*
+		 * A TX-descriptor producer (an IRQ) might have gotten
+		 * inbetween, making the ring free again. Since xmit is
+		 * serialized, this is the only situation we have to
+		 * re-test.
+		 */
+		if (!tx_ring_full(ap, ap->tx_ret_csm, idx))
+			netif_wake_queue(dev);
+	}
+
+	dev->trans_start = jiffies;
+	return NETDEV_TX_OK;
+
+overflow:
+	/*
+	 * This race condition is unavoidable with lock-free drivers.
+	 * We wake up the queue _before_ tx_prd is advanced, so that we can
+	 * enter hard_start_xmit too early, while tx ring still looks closed.
+	 * This happens ~1-4 times per 100000 packets, so that we can allow
+	 * to loop syncing to other CPU. Probably, we need an additional
+	 * wmb() in ace_tx_intr as well.
+	 *
+	 * Note that this race is relieved by reserving one more entry
+	 * in tx ring than it is necessary (see original non-SG driver).
+	 * However, with SG we need to reserve 2*MAX_SKB_FRAGS+1, which
+	 * is already overkill.
+	 *
+	 * Alternative is to return with 1 not throttling queue. In this
+	 * case loop becomes longer, no more useful effects.
+	 */
+	if (time_before(jiffies, maxjiff)) {
+		barrier();
+		cpu_relax();
+		goto restart;
+	}
+	
+	/* The ring is stuck full. */
+	printk(KERN_WARNING "%s: Transmit ring stuck full\n", dev->name);
+	return NETDEV_TX_BUSY;
+}
+
+
+static int ace_change_mtu(struct net_device *dev, int new_mtu)
+{
+	struct ace_private *ap = netdev_priv(dev);
+	struct ace_regs __iomem *regs = ap->regs;
+
+	if (new_mtu > ACE_JUMBO_MTU)
+		return -EINVAL;
+
+	writel(new_mtu + ETH_HLEN + 4, &regs->IfMtu);
+	dev->mtu = new_mtu;
+
+	if (new_mtu > ACE_STD_MTU) {
+		if (!(ap->jumbo)) {
+			printk(KERN_INFO "%s: Enabling Jumbo frame "
+			       "support\n", dev->name);
+			ap->jumbo = 1;
+			if (!test_and_set_bit(0, &ap->jumbo_refill_busy))
+				ace_load_jumbo_rx_ring(ap, RX_JUMBO_SIZE);
+			ace_set_rxtx_parms(dev, 1);
+		}
+	} else {
+		while (test_and_set_bit(0, &ap->jumbo_refill_busy));
+		ace_sync_irq(dev->irq);
+		ace_set_rxtx_parms(dev, 0);
+		if (ap->jumbo) {
+			struct cmd cmd;
+
+			cmd.evt = C_RESET_JUMBO_RNG;
+			cmd.code = 0;
+			cmd.idx = 0;
+			ace_issue_cmd(regs, &cmd);
+		}
+	}
+
+	return 0;
+}
+
+static int ace_get_settings(struct net_device *dev, struct ethtool_cmd *ecmd)
+{
+	struct ace_private *ap = netdev_priv(dev);
+	struct ace_regs __iomem *regs = ap->regs;
+	u32 link;
+
+	memset(ecmd, 0, sizeof(struct ethtool_cmd));
+	ecmd->supported =
+		(SUPPORTED_10baseT_Half | SUPPORTED_10baseT_Full |
+		 SUPPORTED_100baseT_Half | SUPPORTED_100baseT_Full |
+		 SUPPORTED_1000baseT_Half | SUPPORTED_1000baseT_Full |
+		 SUPPORTED_Autoneg | SUPPORTED_FIBRE);
+
+	ecmd->port = PORT_FIBRE;
+	ecmd->transceiver = XCVR_INTERNAL;
+
+	link = readl(&regs->GigLnkState);
+	if (link & LNK_1000MB)
+		ecmd->speed = SPEED_1000;
+	else {
+		link = readl(&regs->FastLnkState);
+		if (link & LNK_100MB)
+			ecmd->speed = SPEED_100;
+		else if (link & LNK_10MB)
+			ecmd->speed = SPEED_10;
+		else
+			ecmd->speed = 0;
+	}
+	if (link & LNK_FULL_DUPLEX)
+		ecmd->duplex = DUPLEX_FULL;
+	else
+		ecmd->duplex = DUPLEX_HALF;
+
+	if (link & LNK_NEGOTIATE)
+		ecmd->autoneg = AUTONEG_ENABLE;
+	else
+		ecmd->autoneg = AUTONEG_DISABLE;
+
+#if 0
+	/*
+	 * Current struct ethtool_cmd is insufficient
+	 */
+	ecmd->trace = readl(&regs->TuneTrace);
+
+	ecmd->txcoal = readl(&regs->TuneTxCoalTicks);
+	ecmd->rxcoal = readl(&regs->TuneRxCoalTicks);
+#endif
+	ecmd->maxtxpkt = readl(&regs->TuneMaxTxDesc);
+	ecmd->maxrxpkt = readl(&regs->TuneMaxRxDesc);
+
+	return 0;
+}
+
+static int ace_set_settings(struct net_device *dev, struct ethtool_cmd *ecmd)
+{
+	struct ace_private *ap = netdev_priv(dev);
+	struct ace_regs __iomem *regs = ap->regs;
+	u32 link, speed;
+
+	link = readl(&regs->GigLnkState);
+	if (link & LNK_1000MB)
+		speed = SPEED_1000;
+	else {
+		link = readl(&regs->FastLnkState);
+		if (link & LNK_100MB)
+			speed = SPEED_100;
+		else if (link & LNK_10MB)
+			speed = SPEED_10;
+		else
+			speed = SPEED_100;
+	}
+
+	link = LNK_ENABLE | LNK_1000MB | LNK_100MB | LNK_10MB |
+		LNK_RX_FLOW_CTL_Y | LNK_NEG_FCTL;
+	if (!ACE_IS_TIGON_I(ap))
+		link |= LNK_TX_FLOW_CTL_Y;
+	if (ecmd->autoneg == AUTONEG_ENABLE)
+		link |= LNK_NEGOTIATE;
+	if (ecmd->speed != speed) {
+		link &= ~(LNK_1000MB | LNK_100MB | LNK_10MB);
+		switch (speed) {
+		case SPEED_1000:
+			link |= LNK_1000MB;
+			break;
+		case SPEED_100:
+			link |= LNK_100MB;
+			break;
+		case SPEED_10:
+			link |= LNK_10MB;
+			break;
+		}
+	}
+
+	if (ecmd->duplex == DUPLEX_FULL)
+		link |= LNK_FULL_DUPLEX;
+
+	if (link != ap->link) {
+		struct cmd cmd;
+		printk(KERN_INFO "%s: Renegotiating link state\n",
+		       dev->name);
+
+		ap->link = link;
+		writel(link, &regs->TuneLink);
+		if (!ACE_IS_TIGON_I(ap))
+			writel(link, &regs->TuneFastLink);
+		wmb();
+
+		cmd.evt = C_LNK_NEGOTIATION;
+		cmd.code = 0;
+		cmd.idx = 0;
+		ace_issue_cmd(regs, &cmd);
+	}
+	return 0;
+}
+
+static void ace_get_drvinfo(struct net_device *dev, 
+			    struct ethtool_drvinfo *info)
+{
+	struct ace_private *ap = netdev_priv(dev);
+
+	strlcpy(info->driver, "acenic", sizeof(info->driver));
+	snprintf(info->version, sizeof(info->version), "%i.%i.%i", 
+		tigonFwReleaseMajor, tigonFwReleaseMinor,
+		tigonFwReleaseFix);
+
+	if (ap->pdev)
+		strlcpy(info->bus_info, pci_name(ap->pdev), 
+			sizeof(info->bus_info));
+
+}
+
+/*
+ * Set the hardware MAC address.
+ */
+static int ace_set_mac_addr(struct net_device *dev, void *p)
+{
+	struct ace_private *ap = netdev_priv(dev);
+	struct ace_regs __iomem *regs = ap->regs;
+	struct sockaddr *addr=p;
+	u8 *da;
+	struct cmd cmd;
+
+	if(netif_running(dev))
+		return -EBUSY;
+
+	memcpy(dev->dev_addr, addr->sa_data,dev->addr_len);
+
+	da = (u8 *)dev->dev_addr;
+
+	writel(da[0] << 8 | da[1], &regs->MacAddrHi);
+	writel((da[2] << 24) | (da[3] << 16) | (da[4] << 8) | da[5],
+	       &regs->MacAddrLo);
+
+	cmd.evt = C_SET_MAC_ADDR;
+	cmd.code = 0;
+	cmd.idx = 0;
+	ace_issue_cmd(regs, &cmd);
+
+	return 0;
+}
+
+
+static void ace_set_multicast_list(struct net_device *dev)
+{
+	struct ace_private *ap = netdev_priv(dev);
+	struct ace_regs __iomem *regs = ap->regs;
+	struct cmd cmd;
+
+	if ((dev->flags & IFF_ALLMULTI) && !(ap->mcast_all)) {
+		cmd.evt = C_SET_MULTICAST_MODE;
+		cmd.code = C_C_MCAST_ENABLE;
+		cmd.idx = 0;
+		ace_issue_cmd(regs, &cmd);
+		ap->mcast_all = 1;
+	} else if (ap->mcast_all) {
+		cmd.evt = C_SET_MULTICAST_MODE;
+		cmd.code = C_C_MCAST_DISABLE;
+		cmd.idx = 0;
+		ace_issue_cmd(regs, &cmd);
+		ap->mcast_all = 0;
+	}
+
+	if ((dev->flags & IFF_PROMISC) && !(ap->promisc)) {
+		cmd.evt = C_SET_PROMISC_MODE;
+		cmd.code = C_C_PROMISC_ENABLE;
+		cmd.idx = 0;
+		ace_issue_cmd(regs, &cmd);
+		ap->promisc = 1;
+	}else if (!(dev->flags & IFF_PROMISC) && (ap->promisc)) {
+		cmd.evt = C_SET_PROMISC_MODE;
+		cmd.code = C_C_PROMISC_DISABLE;
+		cmd.idx = 0;
+		ace_issue_cmd(regs, &cmd);
+		ap->promisc = 0;
+	}
+
+	/*
+	 * For the time being multicast relies on the upper layers
+	 * filtering it properly. The Firmware does not allow one to
+	 * set the entire multicast list at a time and keeping track of
+	 * it here is going to be messy.
+	 */
+	if ((dev->mc_count) && !(ap->mcast_all)) {
+		cmd.evt = C_SET_MULTICAST_MODE;
+		cmd.code = C_C_MCAST_ENABLE;
+		cmd.idx = 0;
+		ace_issue_cmd(regs, &cmd);
+	}else if (!ap->mcast_all) {
+		cmd.evt = C_SET_MULTICAST_MODE;
+		cmd.code = C_C_MCAST_DISABLE;
+		cmd.idx = 0;
+		ace_issue_cmd(regs, &cmd);
+	}
+}
+
+
+static struct net_device_stats *ace_get_stats(struct net_device *dev)
+{
+	struct ace_private *ap = netdev_priv(dev);
+	struct ace_mac_stats __iomem *mac_stats =
+		(struct ace_mac_stats __iomem *)ap->regs->Stats;
+
+	ap->stats.rx_missed_errors = readl(&mac_stats->drop_space);
+	ap->stats.multicast = readl(&mac_stats->kept_mc);
+	ap->stats.collisions = readl(&mac_stats->coll);
+
+	return &ap->stats;
+}
+
+
+static void __devinit ace_copy(struct ace_regs __iomem *regs, void *src,
+			    u32 dest, int size)
+{
+	void __iomem *tdest;
+	u32 *wsrc;
+	short tsize, i;
+
+	if (size <= 0)
+		return;
+
+	while (size > 0) {
+		tsize = min_t(u32, ((~dest & (ACE_WINDOW_SIZE - 1)) + 1),
+			    min_t(u32, size, ACE_WINDOW_SIZE));
+		tdest = (void __iomem *) &regs->Window + 
+			(dest & (ACE_WINDOW_SIZE - 1));
+		writel(dest & ~(ACE_WINDOW_SIZE - 1), &regs->WinBase);
+		/*
+		 * This requires byte swapping on big endian, however
+		 * writel does that for us
+		 */
+		wsrc = src;
+		for (i = 0; i < (tsize / 4); i++) {
+			writel(wsrc[i], tdest + i*4);
+		}
+		dest += tsize;
+		src += tsize;
+		size -= tsize;
+	}
+
+	return;
+}
+
+
+static void __devinit ace_clear(struct ace_regs __iomem *regs, u32 dest, int size)
+{
+	void __iomem *tdest;
+	short tsize = 0, i;
+
+	if (size <= 0)
+		return;
+
+	while (size > 0) {
+		tsize = min_t(u32, ((~dest & (ACE_WINDOW_SIZE - 1)) + 1),
+				min_t(u32, size, ACE_WINDOW_SIZE));
+		tdest = (void __iomem *) &regs->Window + 
+			(dest & (ACE_WINDOW_SIZE - 1));
+		writel(dest & ~(ACE_WINDOW_SIZE - 1), &regs->WinBase);
+
+		for (i = 0; i < (tsize / 4); i++) {
+			writel(0, tdest + i*4);
+		}
+
+		dest += tsize;
+		size -= tsize;
+	}
+
+	return;
+}
+
+
+/*
+ * Download the firmware into the SRAM on the NIC
+ *
+ * This operation requires the NIC to be halted and is performed with
+ * interrupts disabled and with the spinlock hold.
+ */
+int __devinit ace_load_firmware(struct net_device *dev)
+{
+	struct ace_private *ap = netdev_priv(dev);
+	struct ace_regs __iomem *regs = ap->regs;
+
+	if (!(readl(&regs->CpuCtrl) & CPU_HALTED)) {
+		printk(KERN_ERR "%s: trying to download firmware while the "
+		       "CPU is running!\n", ap->name);
+		return -EFAULT;
+	}
+
+	/*
+	 * Do not try to clear more than 512KB or we end up seeing
+	 * funny things on NICs with only 512KB SRAM
+	 */
+	ace_clear(regs, 0x2000, 0x80000-0x2000);
+	if (ACE_IS_TIGON_I(ap)) {
+		ace_copy(regs, tigonFwText, tigonFwTextAddr, tigonFwTextLen);
+		ace_copy(regs, tigonFwData, tigonFwDataAddr, tigonFwDataLen);
+		ace_copy(regs, tigonFwRodata, tigonFwRodataAddr,
+			 tigonFwRodataLen);
+		ace_clear(regs, tigonFwBssAddr, tigonFwBssLen);
+		ace_clear(regs, tigonFwSbssAddr, tigonFwSbssLen);
+	}else if (ap->version == 2) {
+		ace_clear(regs, tigon2FwBssAddr, tigon2FwBssLen);
+		ace_clear(regs, tigon2FwSbssAddr, tigon2FwSbssLen);
+		ace_copy(regs, tigon2FwText, tigon2FwTextAddr,tigon2FwTextLen);
+		ace_copy(regs, tigon2FwRodata, tigon2FwRodataAddr,
+			 tigon2FwRodataLen);
+		ace_copy(regs, tigon2FwData, tigon2FwDataAddr,tigon2FwDataLen);
+	}
+
+	return 0;
+}
+
+
+/*
+ * The eeprom on the AceNIC is an Atmel i2c EEPROM.
+ *
+ * Accessing the EEPROM is `interesting' to say the least - don't read
+ * this code right after dinner.
+ *
+ * This is all about black magic and bit-banging the device .... I
+ * wonder in what hospital they have put the guy who designed the i2c
+ * specs.
+ *
+ * Oh yes, this is only the beginning!
+ *
+ * Thanks to Stevarino Webinski for helping tracking down the bugs in the
+ * code i2c readout code by beta testing all my hacks.
+ */
+static void __devinit eeprom_start(struct ace_regs __iomem *regs)
+{
+	u32 local;
+
+	readl(&regs->LocalCtrl);
+	udelay(ACE_SHORT_DELAY);
+	local = readl(&regs->LocalCtrl);
+	local |= EEPROM_DATA_OUT | EEPROM_WRITE_ENABLE;
+	writel(local, &regs->LocalCtrl);
+	readl(&regs->LocalCtrl);
+	mb();
+	udelay(ACE_SHORT_DELAY);
+	local |= EEPROM_CLK_OUT;
+	writel(local, &regs->LocalCtrl);
+	readl(&regs->LocalCtrl);
+	mb();
+	udelay(ACE_SHORT_DELAY);
+	local &= ~EEPROM_DATA_OUT;
+	writel(local, &regs->LocalCtrl);
+	readl(&regs->LocalCtrl);
+	mb();
+	udelay(ACE_SHORT_DELAY);
+	local &= ~EEPROM_CLK_OUT;
+	writel(local, &regs->LocalCtrl);
+	readl(&regs->LocalCtrl);
+	mb();
+}
+
+
+static void __devinit eeprom_prep(struct ace_regs __iomem *regs, u8 magic)
+{
+	short i;
+	u32 local;
+
+	udelay(ACE_SHORT_DELAY);
+	local = readl(&regs->LocalCtrl);
+	local &= ~EEPROM_DATA_OUT;
+	local |= EEPROM_WRITE_ENABLE;
+	writel(local, &regs->LocalCtrl);
+	readl(&regs->LocalCtrl);
+	mb();
+
+	for (i = 0; i < 8; i++, magic <<= 1) {
+		udelay(ACE_SHORT_DELAY);
+		if (magic & 0x80) 
+			local |= EEPROM_DATA_OUT;
+		else
+			local &= ~EEPROM_DATA_OUT;
+		writel(local, &regs->LocalCtrl);
+		readl(&regs->LocalCtrl);
+		mb();
+
+		udelay(ACE_SHORT_DELAY);
+		local |= EEPROM_CLK_OUT;
+		writel(local, &regs->LocalCtrl);
+		readl(&regs->LocalCtrl);
+		mb();
+		udelay(ACE_SHORT_DELAY);
+		local &= ~(EEPROM_CLK_OUT | EEPROM_DATA_OUT);
+		writel(local, &regs->LocalCtrl);
+		readl(&regs->LocalCtrl);
+		mb();
+	}
+}
+
+
+static int __devinit eeprom_check_ack(struct ace_regs __iomem *regs)
+{
+	int state;
+	u32 local;
+
+	local = readl(&regs->LocalCtrl);
+	local &= ~EEPROM_WRITE_ENABLE;
+	writel(local, &regs->LocalCtrl);
+	readl(&regs->LocalCtrl);
+	mb();
+	udelay(ACE_LONG_DELAY);
+	local |= EEPROM_CLK_OUT;
+	writel(local, &regs->LocalCtrl);
+	readl(&regs->LocalCtrl);
+	mb();
+	udelay(ACE_SHORT_DELAY);
+	/* sample data in middle of high clk */
+	state = (readl(&regs->LocalCtrl) & EEPROM_DATA_IN) != 0;
+	udelay(ACE_SHORT_DELAY);
+	mb();
+	writel(readl(&regs->LocalCtrl) & ~EEPROM_CLK_OUT, &regs->LocalCtrl);
+	readl(&regs->LocalCtrl);
+	mb();
+
+	return state;
+}
+
+
+static void __devinit eeprom_stop(struct ace_regs __iomem *regs)
+{
+	u32 local;
+
+	udelay(ACE_SHORT_DELAY);
+	local = readl(&regs->LocalCtrl);
+	local |= EEPROM_WRITE_ENABLE;
+	writel(local, &regs->LocalCtrl);
+	readl(&regs->LocalCtrl);
+	mb();
+	udelay(ACE_SHORT_DELAY);
+	local &= ~EEPROM_DATA_OUT;
+	writel(local, &regs->LocalCtrl);
+	readl(&regs->LocalCtrl);
+	mb();
+	udelay(ACE_SHORT_DELAY);
+	local |= EEPROM_CLK_OUT;
+	writel(local, &regs->LocalCtrl);
+	readl(&regs->LocalCtrl);
+	mb();
+	udelay(ACE_SHORT_DELAY);
+	local |= EEPROM_DATA_OUT;
+	writel(local, &regs->LocalCtrl);
+	readl(&regs->LocalCtrl);
+	mb();
+	udelay(ACE_LONG_DELAY);
+	local &= ~EEPROM_CLK_OUT;
+	writel(local, &regs->LocalCtrl);
+	mb();
+}
+
+
+/*
+ * Read a whole byte from the EEPROM.
+ */
+static int __devinit read_eeprom_byte(struct net_device *dev,
+				   unsigned long offset)
+{
+	struct ace_private *ap = netdev_priv(dev);
+	struct ace_regs __iomem *regs = ap->regs;
+	unsigned long flags;
+	u32 local;
+	int result = 0;
+	short i;
+
+	if (!dev) {
+		printk(KERN_ERR "No device!\n");
+		result = -ENODEV;
+		goto out;
+	}
+
+	/*
+	 * Don't take interrupts on this CPU will bit banging
+	 * the %#%#@$ I2C device
+	 */
+	local_irq_save(flags);
+
+	eeprom_start(regs);
+
+	eeprom_prep(regs, EEPROM_WRITE_SELECT);
+	if (eeprom_check_ack(regs)) {
+		local_irq_restore(flags);
+		printk(KERN_ERR "%s: Unable to sync eeprom\n", ap->name);
+		result = -EIO;
+		goto eeprom_read_error;
+	}
+
+	eeprom_prep(regs, (offset >> 8) & 0xff);
+	if (eeprom_check_ack(regs)) {
+		local_irq_restore(flags);
+		printk(KERN_ERR "%s: Unable to set address byte 0\n",
+		       ap->name);
+		result = -EIO;
+		goto eeprom_read_error;
+	}
+
+	eeprom_prep(regs, offset & 0xff);
+	if (eeprom_check_ack(regs)) {
+		local_irq_restore(flags);
+		printk(KERN_ERR "%s: Unable to set address byte 1\n",
+		       ap->name);
+		result = -EIO;
+		goto eeprom_read_error;
+	}
+
+	eeprom_start(regs);
+	eeprom_prep(regs, EEPROM_READ_SELECT);
+	if (eeprom_check_ack(regs)) {
+		local_irq_restore(flags);
+		printk(KERN_ERR "%s: Unable to set READ_SELECT\n",
+		       ap->name);
+		result = -EIO;
+		goto eeprom_read_error;
+	}
+
+	for (i = 0; i < 8; i++) {
+		local = readl(&regs->LocalCtrl);
+		local &= ~EEPROM_WRITE_ENABLE;
+		writel(local, &regs->LocalCtrl);
+		readl(&regs->LocalCtrl);
+		udelay(ACE_LONG_DELAY);
+		mb();
+		local |= EEPROM_CLK_OUT;
+		writel(local, &regs->LocalCtrl);
+		readl(&regs->LocalCtrl);
+		mb();
+		udelay(ACE_SHORT_DELAY);
+		/* sample data mid high clk */
+		result = (result << 1) |
+			((readl(&regs->LocalCtrl) & EEPROM_DATA_IN) != 0);
+		udelay(ACE_SHORT_DELAY);
+		mb();
+		local = readl(&regs->LocalCtrl);
+		local &= ~EEPROM_CLK_OUT;
+		writel(local, &regs->LocalCtrl);
+		readl(&regs->LocalCtrl);
+		udelay(ACE_SHORT_DELAY);
+		mb();
+		if (i == 7) {
+			local |= EEPROM_WRITE_ENABLE;
+			writel(local, &regs->LocalCtrl);
+			readl(&regs->LocalCtrl);
+			mb();
+			udelay(ACE_SHORT_DELAY);
+		}
+	}
+
+	local |= EEPROM_DATA_OUT;
+	writel(local, &regs->LocalCtrl);
+	readl(&regs->LocalCtrl);
+	mb();
+	udelay(ACE_SHORT_DELAY);
+	writel(readl(&regs->LocalCtrl) | EEPROM_CLK_OUT, &regs->LocalCtrl);
+	readl(&regs->LocalCtrl);
+	udelay(ACE_LONG_DELAY);
+	writel(readl(&regs->LocalCtrl) & ~EEPROM_CLK_OUT, &regs->LocalCtrl);
+	readl(&regs->LocalCtrl);
+	mb();
+	udelay(ACE_SHORT_DELAY);
+	eeprom_stop(regs);
+
+	local_irq_restore(flags);
+ out:
+	return result;
+
+ eeprom_read_error:
+	printk(KERN_ERR "%s: Unable to read eeprom byte 0x%02lx\n",
+	       ap->name, offset);
+	goto out;
+}
+
+
+/*
+ * Local variables:
+ * compile-command: "gcc -D__SMP__ -D__KERNEL__ -DMODULE -I../../include -Wall -Wstrict-prototypes -O2 -fomit-frame-pointer -pipe -fno-strength-reduce -DMODVERSIONS -include ../../include/linux/modversions.h   -c -o acenic.o acenic.c"
+ * End:
+ */