usb: phy: tegra: Program new PHY parameters
The Tegra30 TRM recommends configuration of certain PHY parameters for
optimal quality. Program the following registers based on device tree
parameters:
- UTMIP_XCVR_HSSLEW: HS slew rate control.
- UTMIP_HSSQUELCH_LEVEL: HS squelch detector level
- UTMIP_HSDISCON_LEVEL: HS disconnect detector level.
These registers exist in Tegra20, but programming them hasn't been
necessary, so these parameters won't be set on Tegra20 to keep the
device trees backward compatible.
Additionally, the UTMIP_XCVR_SETUP parameter can be set from fuses
instead of a software-programmed value, as the optimal value can
vary between invidual boards. The boolean property
nvidia,xcvr-setup-use-fuses can be used to enable this behaviour.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
diff --git a/drivers/usb/phy/phy-tegra-usb.c b/drivers/usb/phy/phy-tegra-usb.c
index 1ad184a..3bfb3d1 100644
--- a/drivers/usb/phy/phy-tegra-usb.c
+++ b/drivers/usb/phy/phy-tegra-usb.c
@@ -99,11 +99,15 @@
#define UTMIP_FORCE_PD2_POWERDOWN (1 << 16)
#define UTMIP_FORCE_PDZI_POWERDOWN (1 << 18)
#define UTMIP_XCVR_LSBIAS_SEL (1 << 21)
-#define UTMIP_XCVR_HSSLEW_MSB(x) (((x) & 0x7f) << 25)
+#define UTMIP_XCVR_HSSLEW(x) (((x) & 0x3) << 4)
+#define UTMIP_XCVR_HSSLEW_MSB(x) ((((x) & 0x1fc) >> 2) << 25)
#define UTMIP_BIAS_CFG0 0x80c
#define UTMIP_OTGPD (1 << 11)
#define UTMIP_BIASPD (1 << 10)
+#define UTMIP_HSSQUELCH_LEVEL(x) (((x) & 0x3) << 0)
+#define UTMIP_HSDISCON_LEVEL(x) (((x) & 0x3) << 2)
+#define UTMIP_HSDISCON_LEVEL_MSB(x) ((((x) & 0x4) >> 2) << 24)
#define UTMIP_HSRX_CFG0 0x810
#define UTMIP_ELASTIC_LIMIT(x) (((x) & 0x1f) << 10)
@@ -255,6 +259,7 @@
{
unsigned long val, flags;
void __iomem *base = phy->pad_regs;
+ struct tegra_utmip_config *config = phy->config;
clk_prepare_enable(phy->pad_clk);
@@ -263,6 +268,16 @@
if (utmip_pad_count++ == 0) {
val = readl(base + UTMIP_BIAS_CFG0);
val &= ~(UTMIP_OTGPD | UTMIP_BIASPD);
+
+ if (phy->soc_config->requires_extra_tuning_parameters) {
+ val &= ~(UTMIP_HSSQUELCH_LEVEL(~0) |
+ UTMIP_HSDISCON_LEVEL(~0) |
+ UTMIP_HSDISCON_LEVEL_MSB(~0));
+
+ val |= UTMIP_HSSQUELCH_LEVEL(config->hssquelch_level);
+ val |= UTMIP_HSDISCON_LEVEL(config->hsdiscon_level);
+ val |= UTMIP_HSDISCON_LEVEL_MSB(config->hsdiscon_level);
+ }
writel(val, base + UTMIP_BIAS_CFG0);
}
@@ -431,12 +446,20 @@
val &= ~(UTMIP_FORCE_PD_POWERDOWN | UTMIP_FORCE_PD2_POWERDOWN |
UTMIP_FORCE_PDZI_POWERDOWN | UTMIP_XCVR_LSBIAS_SEL |
UTMIP_XCVR_SETUP(~0) | UTMIP_XCVR_SETUP_MSB(~0) |
- UTMIP_XCVR_LSFSLEW(~0) | UTMIP_XCVR_LSRSLEW(~0) |
- UTMIP_XCVR_HSSLEW_MSB(~0));
- val |= UTMIP_XCVR_SETUP(config->xcvr_setup);
- val |= UTMIP_XCVR_SETUP_MSB(config->xcvr_setup);
+ UTMIP_XCVR_LSFSLEW(~0) | UTMIP_XCVR_LSRSLEW(~0));
+
+ if (!config->xcvr_setup_use_fuses) {
+ val |= UTMIP_XCVR_SETUP(config->xcvr_setup);
+ val |= UTMIP_XCVR_SETUP_MSB(config->xcvr_setup);
+ }
val |= UTMIP_XCVR_LSFSLEW(config->xcvr_lsfslew);
val |= UTMIP_XCVR_LSRSLEW(config->xcvr_lsrslew);
+
+ if (phy->soc_config->requires_extra_tuning_parameters) {
+ val &= ~(UTMIP_XCVR_HSSLEW(~0) | UTMIP_XCVR_HSSLEW_MSB(~0));
+ val |= UTMIP_XCVR_HSSLEW(config->xcvr_hsslew);
+ val |= UTMIP_XCVR_HSSLEW_MSB(config->xcvr_hsslew);
+ }
writel(val, base + UTMIP_XCVR_CFG0);
val = readl(base + UTMIP_XCVR_CFG1);
@@ -450,14 +473,14 @@
val |= UTMIP_BIAS_PDTRK_COUNT(0x5);
writel(val, base + UTMIP_BIAS_CFG1);
- if (phy->is_legacy_phy) {
- val = readl(base + UTMIP_SPARE_CFG0);
- if (phy->mode == USB_DR_MODE_PERIPHERAL)
- val &= ~FUSE_SETUP_SEL;
- else
- val |= FUSE_SETUP_SEL;
- writel(val, base + UTMIP_SPARE_CFG0);
- } else {
+ val = readl(base + UTMIP_SPARE_CFG0);
+ if (config->xcvr_setup_use_fuses)
+ val |= FUSE_SETUP_SEL;
+ else
+ val &= ~FUSE_SETUP_SEL;
+ writel(val, base + UTMIP_SPARE_CFG0);
+
+ if (!phy->is_legacy_phy) {
val = readl(base + USB_SUSP_CTRL);
val |= UTMIP_PHY_ENABLE;
writel(val, base + USB_SUSP_CTRL);
@@ -888,11 +911,6 @@
if (err < 0)
return err;
- err = read_utmi_param(pdev, "nvidia,xcvr-setup",
- &config->xcvr_setup);
- if (err < 0)
- return err;
-
err = read_utmi_param(pdev, "nvidia,xcvr-lsfslew",
&config->xcvr_lsfslew);
if (err < 0)
@@ -903,6 +921,33 @@
if (err < 0)
return err;
+ if (tegra_phy->soc_config->requires_extra_tuning_parameters) {
+ err = read_utmi_param(pdev, "nvidia,xcvr-hsslew",
+ &config->xcvr_hsslew);
+ if (err < 0)
+ return err;
+
+ err = read_utmi_param(pdev, "nvidia,hssquelch-level",
+ &config->hssquelch_level);
+ if (err < 0)
+ return err;
+
+ err = read_utmi_param(pdev, "nvidia,hsdiscon-level",
+ &config->hsdiscon_level);
+ if (err < 0)
+ return err;
+ }
+
+ config->xcvr_setup_use_fuses = of_property_read_bool(
+ pdev->dev.of_node, "nvidia,xcvr-setup-use-fuses");
+
+ if (!config->xcvr_setup_use_fuses) {
+ err = read_utmi_param(pdev, "nvidia,xcvr-setup",
+ &config->xcvr_setup);
+ if (err < 0)
+ return err;
+ }
+
return 0;
}
diff --git a/include/linux/usb/tegra_usb_phy.h b/include/linux/usb/tegra_usb_phy.h
index d3a63c3..1de16c3 100644
--- a/include/linux/usb/tegra_usb_phy.h
+++ b/include/linux/usb/tegra_usb_phy.h
@@ -41,9 +41,13 @@
u8 elastic_limit;
u8 idle_wait_delay;
u8 term_range_adj;
+ bool xcvr_setup_use_fuses;
u8 xcvr_setup;
u8 xcvr_lsfslew;
u8 xcvr_lsrslew;
+ u8 xcvr_hsslew;
+ u8 hssquelch_level;
+ u8 hsdiscon_level;
};
enum tegra_usb_phy_port_speed {