IXP4xx: Fix IO_SPACE_LIMIT for 2.6.31-rc core PCI changes
2.6.31-rc kernels don't boot on my ixp4xx box (ds101), because the libata
driver doesn't find the PCI IDE controller any more. 2.6.30 was fine.
I traced this to a PCI update (1f82de10d6b1d845155363c895c552e61b36b51a)
in 2.6.30-git19. Diffing the kernel boot logs from 2.6.30-git18 and
2.6.30-git19 illustrates the breakage:
> --- dmesg-2.6.30-git18 2009-08-04 01:45:22.000000000 +0200
> +++ dmesg-2.6.30-git19 2009-08-04 01:45:46.000000000 +0200
> @@ -26,6 +26,13 @@
> pci 0000:00:02.2: PME# supported from D0 D1 D2 D3hot
> pci 0000:00:02.2: PME# disabled
> PCI: bus0: Fast back to back transfers disabled
> +pci 0000:00:01.0: BAR 0: can't allocate I/O resource [0x10000-0xffff]
> +pci 0000:00:01.0: BAR 1: can't allocate I/O resource [0x10000-0xffff]
> +pci 0000:00:01.0: BAR 2: can't allocate I/O resource [0x10000-0xffff]
> +pci 0000:00:01.0: BAR 3: can't allocate I/O resource [0x10000-0xffff]
> +pci 0000:00:01.0: BAR 4: can't allocate I/O resource [0x10000-0xffff]
> +pci 0000:00:02.0: BAR 4: can't allocate I/O resource [0x10000-0xffff]
> +pci 0000:00:02.1: BAR 4: can't allocate I/O resource [0x10000-0xffff]
> bio: create slab <bio-0> at 0
> SCSI subsystem initialized
> NET: Registered protocol family 2
> @@ -44,11 +51,7 @@
> console [ttyS0] enabled
> serial8250.0: ttyS1 at MMIO 0xc8001000 (irq = 13) is a XScale
> Driver 'sd' needs updating - please use bus_type methods
> -PCI: enabling device 0000:00:01.0 (0140 -> 0141)
> -scsi0 : pata_artop
> -scsi1 : pata_artop
> -ata1: PATA max UDMA/100 cmd 0x1050 ctl 0x1060 bmdma 0x1040 irq 28
> -ata2: PATA max UDMA/100 cmd 0x1058 ctl 0x1064 bmdma 0x1048 irq 28
> +pata_artop 0000:00:01.0: no available native port
> Using configured DiskOnChip probe address 0x50000000
> DiskOnChip found at 0x50000000
> NAND device: Manufacturer ID: 0x98, Chip ID: 0x73 (Toshiba NAND 16MiB 3,3V 8-bit)
The specific change in 1f82de10d6b1d845155363c895c552e61b36b51a responsible
for this failure turned out to be the following:
> --- a/drivers/pci/probe.c
> +++ b/drivers/pci/probe.c
> @@ -193,7 +193,7 @@ int __pci_read_base(struct pci_dev *dev, enum pci_bar_type type,
> res->flags |= pci_calc_resource_flags(l) | IORESOURCE_SIZEALIGN;
> if (type == pci_bar_io) {
> l &= PCI_BASE_ADDRESS_IO_MASK;
> - mask = PCI_BASE_ADDRESS_IO_MASK & 0xffff;
> + mask = PCI_BASE_ADDRESS_IO_MASK & IO_SPACE_LIMIT;
> } else {
> l &= PCI_BASE_ADDRESS_MEM_MASK;
> mask = (u32)PCI_BASE_ADDRESS_MEM_MASK;
Every arch except arm's ixp4xx defines IO_SPACE_LIMIT as an all-bits-one
bitmask, typically -1UL but sometimes only a 16-bit 0x0000ffff. But ixp4xx
defines it as 0xffff0000, which is now causing the PCI failures.
Russell King noted that ixp4xx has 64KB PCI IO space, so IO_SPACE_LIMIT
should be 0x0000ffff. This patch makes that change, which fixes the PCI
failures on my ixp4xx box.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
1 file changed