| /* |
| * Blackfin Infra-red Driver |
| * |
| * Copyright 2006-2009 Analog Devices Inc. |
| * |
| * Enter bugs at http://blackfin.uclinux.org/ |
| * |
| * Licensed under the GPL-2 or later. |
| * |
| */ |
| #include "bfin_sir.h" |
| |
| #ifdef CONFIG_SIR_BFIN_DMA |
| #define DMA_SIR_RX_XCNT 10 |
| #define DMA_SIR_RX_YCNT (PAGE_SIZE / DMA_SIR_RX_XCNT) |
| #define DMA_SIR_RX_FLUSH_JIFS (HZ * 4 / 250) |
| #endif |
| |
| #if ANOMALY_05000447 |
| static int max_rate = 57600; |
| #else |
| static int max_rate = 115200; |
| #endif |
| |
| static void turnaround_delay(unsigned long last_jif, int mtt) |
| { |
| long ticks; |
| |
| mtt = mtt < 10000 ? 10000 : mtt; |
| ticks = 1 + mtt / (USEC_PER_SEC / HZ); |
| schedule_timeout_uninterruptible(ticks); |
| } |
| |
| static void bfin_sir_init_ports(struct bfin_sir_port *sp, struct platform_device *pdev) |
| { |
| int i; |
| struct resource *res; |
| |
| for (i = 0; i < pdev->num_resources; i++) { |
| res = &pdev->resource[i]; |
| switch (res->flags) { |
| case IORESOURCE_MEM: |
| sp->membase = (void __iomem *)res->start; |
| break; |
| case IORESOURCE_IRQ: |
| sp->irq = res->start; |
| break; |
| case IORESOURCE_DMA: |
| sp->rx_dma_channel = res->start; |
| sp->tx_dma_channel = res->end; |
| break; |
| default: |
| break; |
| } |
| } |
| |
| sp->clk = get_sclk(); |
| #ifdef CONFIG_SIR_BFIN_DMA |
| sp->tx_done = 1; |
| init_timer(&(sp->rx_dma_timer)); |
| #endif |
| } |
| |
| static void bfin_sir_stop_tx(struct bfin_sir_port *port) |
| { |
| #ifdef CONFIG_SIR_BFIN_DMA |
| disable_dma(port->tx_dma_channel); |
| #endif |
| |
| while (!(UART_GET_LSR(port) & THRE)) { |
| cpu_relax(); |
| continue; |
| } |
| |
| UART_CLEAR_IER(port, ETBEI); |
| } |
| |
| static void bfin_sir_enable_tx(struct bfin_sir_port *port) |
| { |
| UART_SET_IER(port, ETBEI); |
| } |
| |
| static void bfin_sir_stop_rx(struct bfin_sir_port *port) |
| { |
| UART_CLEAR_IER(port, ERBFI); |
| } |
| |
| static void bfin_sir_enable_rx(struct bfin_sir_port *port) |
| { |
| UART_SET_IER(port, ERBFI); |
| } |
| |
| static int bfin_sir_set_speed(struct bfin_sir_port *port, int speed) |
| { |
| int ret = -EINVAL; |
| unsigned int quot; |
| unsigned short val, lsr, lcr; |
| static int utime; |
| int count = 10; |
| |
| lcr = WLS(8); |
| |
| switch (speed) { |
| case 9600: |
| case 19200: |
| case 38400: |
| case 57600: |
| case 115200: |
| |
| /* |
| * IRDA is not affected by anomaly 05000230, so there is no |
| * need to tweak the divisor like he UART driver (which will |
| * slightly speed up the baud rate on us). |
| */ |
| quot = (port->clk + (8 * speed)) / (16 * speed); |
| |
| do { |
| udelay(utime); |
| lsr = UART_GET_LSR(port); |
| } while (!(lsr & TEMT) && count--); |
| |
| /* The useconds for 1 bits to transmit */ |
| utime = 1000000 / speed + 1; |
| |
| /* Clear UCEN bit to reset the UART state machine |
| * and control registers |
| */ |
| val = UART_GET_GCTL(port); |
| val &= ~UCEN; |
| UART_PUT_GCTL(port, val); |
| |
| /* Set DLAB in LCR to Access THR RBR IER */ |
| UART_SET_DLAB(port); |
| SSYNC(); |
| |
| UART_PUT_DLL(port, quot & 0xFF); |
| UART_PUT_DLH(port, (quot >> 8) & 0xFF); |
| SSYNC(); |
| |
| /* Clear DLAB in LCR */ |
| UART_CLEAR_DLAB(port); |
| SSYNC(); |
| |
| UART_PUT_LCR(port, lcr); |
| |
| val = UART_GET_GCTL(port); |
| val |= UCEN; |
| UART_PUT_GCTL(port, val); |
| |
| ret = 0; |
| break; |
| default: |
| printk(KERN_WARNING "bfin_sir: Invalid speed %d\n", speed); |
| break; |
| } |
| |
| val = UART_GET_GCTL(port); |
| /* If not add the 'RPOLC', we can't catch the receive interrupt. |
| * It's related with the HW layout and the IR transiver. |
| */ |
| val |= UMOD_IRDA | RPOLC; |
| UART_PUT_GCTL(port, val); |
| return ret; |
| } |
| |
| static int bfin_sir_is_receiving(struct net_device *dev) |
| { |
| struct bfin_sir_self *self = netdev_priv(dev); |
| struct bfin_sir_port *port = self->sir_port; |
| |
| if (!(UART_GET_IER(port) & ERBFI)) |
| return 0; |
| return self->rx_buff.state != OUTSIDE_FRAME; |
| } |
| |
| #ifdef CONFIG_SIR_BFIN_PIO |
| static void bfin_sir_tx_chars(struct net_device *dev) |
| { |
| unsigned int chr; |
| struct bfin_sir_self *self = netdev_priv(dev); |
| struct bfin_sir_port *port = self->sir_port; |
| |
| if (self->tx_buff.len != 0) { |
| chr = *(self->tx_buff.data); |
| UART_PUT_CHAR(port, chr); |
| self->tx_buff.data++; |
| self->tx_buff.len--; |
| } else { |
| self->stats.tx_packets++; |
| self->stats.tx_bytes += self->tx_buff.data - self->tx_buff.head; |
| if (self->newspeed) { |
| bfin_sir_set_speed(port, self->newspeed); |
| self->speed = self->newspeed; |
| self->newspeed = 0; |
| } |
| bfin_sir_stop_tx(port); |
| bfin_sir_enable_rx(port); |
| /* I'm hungry! */ |
| netif_wake_queue(dev); |
| } |
| } |
| |
| static void bfin_sir_rx_chars(struct net_device *dev) |
| { |
| struct bfin_sir_self *self = netdev_priv(dev); |
| struct bfin_sir_port *port = self->sir_port; |
| unsigned char ch; |
| |
| UART_CLEAR_LSR(port); |
| ch = UART_GET_CHAR(port); |
| async_unwrap_char(dev, &self->stats, &self->rx_buff, ch); |
| dev->last_rx = jiffies; |
| } |
| |
| static irqreturn_t bfin_sir_rx_int(int irq, void *dev_id) |
| { |
| struct net_device *dev = dev_id; |
| struct bfin_sir_self *self = netdev_priv(dev); |
| struct bfin_sir_port *port = self->sir_port; |
| |
| spin_lock(&self->lock); |
| while ((UART_GET_LSR(port) & DR)) |
| bfin_sir_rx_chars(dev); |
| spin_unlock(&self->lock); |
| |
| return IRQ_HANDLED; |
| } |
| |
| static irqreturn_t bfin_sir_tx_int(int irq, void *dev_id) |
| { |
| struct net_device *dev = dev_id; |
| struct bfin_sir_self *self = netdev_priv(dev); |
| struct bfin_sir_port *port = self->sir_port; |
| |
| spin_lock(&self->lock); |
| if (UART_GET_LSR(port) & THRE) |
| bfin_sir_tx_chars(dev); |
| spin_unlock(&self->lock); |
| |
| return IRQ_HANDLED; |
| } |
| #endif /* CONFIG_SIR_BFIN_PIO */ |
| |
| #ifdef CONFIG_SIR_BFIN_DMA |
| static void bfin_sir_dma_tx_chars(struct net_device *dev) |
| { |
| struct bfin_sir_self *self = netdev_priv(dev); |
| struct bfin_sir_port *port = self->sir_port; |
| |
| if (!port->tx_done) |
| return; |
| port->tx_done = 0; |
| |
| if (self->tx_buff.len == 0) { |
| self->stats.tx_packets++; |
| if (self->newspeed) { |
| bfin_sir_set_speed(port, self->newspeed); |
| self->speed = self->newspeed; |
| self->newspeed = 0; |
| } |
| bfin_sir_enable_rx(port); |
| port->tx_done = 1; |
| netif_wake_queue(dev); |
| return; |
| } |
| |
| blackfin_dcache_flush_range((unsigned long)(self->tx_buff.data), |
| (unsigned long)(self->tx_buff.data+self->tx_buff.len)); |
| set_dma_config(port->tx_dma_channel, |
| set_bfin_dma_config(DIR_READ, DMA_FLOW_STOP, |
| INTR_ON_BUF, DIMENSION_LINEAR, DATA_SIZE_8, |
| DMA_SYNC_RESTART)); |
| set_dma_start_addr(port->tx_dma_channel, |
| (unsigned long)(self->tx_buff.data)); |
| set_dma_x_count(port->tx_dma_channel, self->tx_buff.len); |
| set_dma_x_modify(port->tx_dma_channel, 1); |
| enable_dma(port->tx_dma_channel); |
| } |
| |
| static irqreturn_t bfin_sir_dma_tx_int(int irq, void *dev_id) |
| { |
| struct net_device *dev = dev_id; |
| struct bfin_sir_self *self = netdev_priv(dev); |
| struct bfin_sir_port *port = self->sir_port; |
| |
| spin_lock(&self->lock); |
| if (!(get_dma_curr_irqstat(port->tx_dma_channel) & DMA_RUN)) { |
| clear_dma_irqstat(port->tx_dma_channel); |
| bfin_sir_stop_tx(port); |
| |
| self->stats.tx_packets++; |
| self->stats.tx_bytes += self->tx_buff.len; |
| self->tx_buff.len = 0; |
| if (self->newspeed) { |
| bfin_sir_set_speed(port, self->newspeed); |
| self->speed = self->newspeed; |
| self->newspeed = 0; |
| } |
| bfin_sir_enable_rx(port); |
| /* I'm hungry! */ |
| netif_wake_queue(dev); |
| port->tx_done = 1; |
| } |
| spin_unlock(&self->lock); |
| |
| return IRQ_HANDLED; |
| } |
| |
| static void bfin_sir_dma_rx_chars(struct net_device *dev) |
| { |
| struct bfin_sir_self *self = netdev_priv(dev); |
| struct bfin_sir_port *port = self->sir_port; |
| int i; |
| |
| UART_CLEAR_LSR(port); |
| |
| for (i = port->rx_dma_buf.head; i < port->rx_dma_buf.tail; i++) |
| async_unwrap_char(dev, &self->stats, &self->rx_buff, port->rx_dma_buf.buf[i]); |
| } |
| |
| void bfin_sir_rx_dma_timeout(struct net_device *dev) |
| { |
| struct bfin_sir_self *self = netdev_priv(dev); |
| struct bfin_sir_port *port = self->sir_port; |
| int x_pos, pos; |
| unsigned long flags; |
| |
| spin_lock_irqsave(&self->lock, flags); |
| x_pos = DMA_SIR_RX_XCNT - get_dma_curr_xcount(port->rx_dma_channel); |
| if (x_pos == DMA_SIR_RX_XCNT) |
| x_pos = 0; |
| |
| pos = port->rx_dma_nrows * DMA_SIR_RX_XCNT + x_pos; |
| |
| if (pos > port->rx_dma_buf.tail) { |
| port->rx_dma_buf.tail = pos; |
| bfin_sir_dma_rx_chars(dev); |
| port->rx_dma_buf.head = port->rx_dma_buf.tail; |
| } |
| spin_unlock_irqrestore(&self->lock, flags); |
| } |
| |
| static irqreturn_t bfin_sir_dma_rx_int(int irq, void *dev_id) |
| { |
| struct net_device *dev = dev_id; |
| struct bfin_sir_self *self = netdev_priv(dev); |
| struct bfin_sir_port *port = self->sir_port; |
| unsigned short irqstat; |
| |
| spin_lock(&self->lock); |
| |
| port->rx_dma_nrows++; |
| port->rx_dma_buf.tail = DMA_SIR_RX_XCNT * port->rx_dma_nrows; |
| bfin_sir_dma_rx_chars(dev); |
| if (port->rx_dma_nrows >= DMA_SIR_RX_YCNT) { |
| port->rx_dma_nrows = 0; |
| port->rx_dma_buf.tail = 0; |
| } |
| port->rx_dma_buf.head = port->rx_dma_buf.tail; |
| |
| irqstat = get_dma_curr_irqstat(port->rx_dma_channel); |
| clear_dma_irqstat(port->rx_dma_channel); |
| spin_unlock(&self->lock); |
| |
| mod_timer(&port->rx_dma_timer, jiffies + DMA_SIR_RX_FLUSH_JIFS); |
| return IRQ_HANDLED; |
| } |
| #endif /* CONFIG_SIR_BFIN_DMA */ |
| |
| static int bfin_sir_startup(struct bfin_sir_port *port, struct net_device *dev) |
| { |
| #ifdef CONFIG_SIR_BFIN_DMA |
| dma_addr_t dma_handle; |
| #endif /* CONFIG_SIR_BFIN_DMA */ |
| |
| if (request_dma(port->rx_dma_channel, "BFIN_UART_RX") < 0) { |
| dev_warn(&dev->dev, "Unable to attach SIR RX DMA channel\n"); |
| return -EBUSY; |
| } |
| |
| if (request_dma(port->tx_dma_channel, "BFIN_UART_TX") < 0) { |
| dev_warn(&dev->dev, "Unable to attach SIR TX DMA channel\n"); |
| free_dma(port->rx_dma_channel); |
| return -EBUSY; |
| } |
| |
| #ifdef CONFIG_SIR_BFIN_DMA |
| |
| set_dma_callback(port->rx_dma_channel, bfin_sir_dma_rx_int, dev); |
| set_dma_callback(port->tx_dma_channel, bfin_sir_dma_tx_int, dev); |
| |
| port->rx_dma_buf.buf = (unsigned char *)dma_alloc_coherent(NULL, PAGE_SIZE, &dma_handle, GFP_DMA); |
| port->rx_dma_buf.head = 0; |
| port->rx_dma_buf.tail = 0; |
| port->rx_dma_nrows = 0; |
| |
| set_dma_config(port->rx_dma_channel, |
| set_bfin_dma_config(DIR_WRITE, DMA_FLOW_AUTO, |
| INTR_ON_ROW, DIMENSION_2D, |
| DATA_SIZE_8, DMA_SYNC_RESTART)); |
| set_dma_x_count(port->rx_dma_channel, DMA_SIR_RX_XCNT); |
| set_dma_x_modify(port->rx_dma_channel, 1); |
| set_dma_y_count(port->rx_dma_channel, DMA_SIR_RX_YCNT); |
| set_dma_y_modify(port->rx_dma_channel, 1); |
| set_dma_start_addr(port->rx_dma_channel, (unsigned long)port->rx_dma_buf.buf); |
| enable_dma(port->rx_dma_channel); |
| |
| port->rx_dma_timer.data = (unsigned long)(dev); |
| port->rx_dma_timer.function = (void *)bfin_sir_rx_dma_timeout; |
| |
| #else |
| |
| if (request_irq(port->irq, bfin_sir_rx_int, IRQF_DISABLED, "BFIN_SIR_RX", dev)) { |
| dev_warn(&dev->dev, "Unable to attach SIR RX interrupt\n"); |
| return -EBUSY; |
| } |
| |
| if (request_irq(port->irq+1, bfin_sir_tx_int, IRQF_DISABLED, "BFIN_SIR_TX", dev)) { |
| dev_warn(&dev->dev, "Unable to attach SIR TX interrupt\n"); |
| free_irq(port->irq, dev); |
| return -EBUSY; |
| } |
| #endif |
| |
| return 0; |
| } |
| |
| static void bfin_sir_shutdown(struct bfin_sir_port *port, struct net_device *dev) |
| { |
| unsigned short val; |
| |
| bfin_sir_stop_rx(port); |
| |
| val = UART_GET_GCTL(port); |
| val &= ~(UCEN | UMOD_MASK | RPOLC); |
| UART_PUT_GCTL(port, val); |
| |
| #ifdef CONFIG_SIR_BFIN_DMA |
| disable_dma(port->tx_dma_channel); |
| disable_dma(port->rx_dma_channel); |
| del_timer(&(port->rx_dma_timer)); |
| dma_free_coherent(NULL, PAGE_SIZE, port->rx_dma_buf.buf, 0); |
| #else |
| free_irq(port->irq+1, dev); |
| free_irq(port->irq, dev); |
| #endif |
| free_dma(port->tx_dma_channel); |
| free_dma(port->rx_dma_channel); |
| } |
| |
| #ifdef CONFIG_PM |
| static int bfin_sir_suspend(struct platform_device *pdev, pm_message_t state) |
| { |
| struct bfin_sir_port *sir_port; |
| struct net_device *dev; |
| struct bfin_sir_self *self; |
| |
| sir_port = platform_get_drvdata(pdev); |
| if (!sir_port) |
| return 0; |
| |
| dev = sir_port->dev; |
| self = netdev_priv(dev); |
| if (self->open) { |
| flush_work(&self->work); |
| bfin_sir_shutdown(self->sir_port, dev); |
| netif_device_detach(dev); |
| } |
| |
| return 0; |
| } |
| static int bfin_sir_resume(struct platform_device *pdev) |
| { |
| struct bfin_sir_port *sir_port; |
| struct net_device *dev; |
| struct bfin_sir_self *self; |
| struct bfin_sir_port *port; |
| |
| sir_port = platform_get_drvdata(pdev); |
| if (!sir_port) |
| return 0; |
| |
| dev = sir_port->dev; |
| self = netdev_priv(dev); |
| port = self->sir_port; |
| if (self->open) { |
| if (self->newspeed) { |
| self->speed = self->newspeed; |
| self->newspeed = 0; |
| } |
| bfin_sir_startup(port, dev); |
| bfin_sir_set_speed(port, 9600); |
| bfin_sir_enable_rx(port); |
| netif_device_attach(dev); |
| } |
| return 0; |
| } |
| #else |
| #define bfin_sir_suspend NULL |
| #define bfin_sir_resume NULL |
| #endif |
| |
| static void bfin_sir_send_work(struct work_struct *work) |
| { |
| struct bfin_sir_self *self = container_of(work, struct bfin_sir_self, work); |
| struct net_device *dev = self->sir_port->dev; |
| struct bfin_sir_port *port = self->sir_port; |
| unsigned short val; |
| int tx_cnt = 10; |
| |
| while (bfin_sir_is_receiving(dev) && --tx_cnt) |
| turnaround_delay(dev->last_rx, self->mtt); |
| |
| bfin_sir_stop_rx(port); |
| |
| /* To avoid losting RX interrupt, we reset IR function before |
| * sending data. We also can set the speed, which will |
| * reset all the UART. |
| */ |
| val = UART_GET_GCTL(port); |
| val &= ~(UMOD_MASK | RPOLC); |
| UART_PUT_GCTL(port, val); |
| SSYNC(); |
| val |= UMOD_IRDA | RPOLC; |
| UART_PUT_GCTL(port, val); |
| SSYNC(); |
| /* bfin_sir_set_speed(port, self->speed); */ |
| |
| #ifdef CONFIG_SIR_BFIN_DMA |
| bfin_sir_dma_tx_chars(dev); |
| #endif |
| bfin_sir_enable_tx(port); |
| dev->trans_start = jiffies; |
| } |
| |
| static int bfin_sir_hard_xmit(struct sk_buff *skb, struct net_device *dev) |
| { |
| struct bfin_sir_self *self = netdev_priv(dev); |
| int speed = irda_get_next_speed(skb); |
| |
| netif_stop_queue(dev); |
| |
| self->mtt = irda_get_mtt(skb); |
| |
| if (speed != self->speed && speed != -1) |
| self->newspeed = speed; |
| |
| self->tx_buff.data = self->tx_buff.head; |
| if (skb->len == 0) |
| self->tx_buff.len = 0; |
| else |
| self->tx_buff.len = async_wrap_skb(skb, self->tx_buff.data, self->tx_buff.truesize); |
| |
| schedule_work(&self->work); |
| dev_kfree_skb(skb); |
| |
| return 0; |
| } |
| |
| static int bfin_sir_ioctl(struct net_device *dev, struct ifreq *ifreq, int cmd) |
| { |
| struct if_irda_req *rq = (struct if_irda_req *)ifreq; |
| struct bfin_sir_self *self = netdev_priv(dev); |
| struct bfin_sir_port *port = self->sir_port; |
| int ret = 0; |
| |
| switch (cmd) { |
| case SIOCSBANDWIDTH: |
| if (capable(CAP_NET_ADMIN)) { |
| if (self->open) { |
| ret = bfin_sir_set_speed(port, rq->ifr_baudrate); |
| bfin_sir_enable_rx(port); |
| } else { |
| dev_warn(&dev->dev, "SIOCSBANDWIDTH: !netif_running\n"); |
| ret = 0; |
| } |
| } |
| break; |
| |
| case SIOCSMEDIABUSY: |
| ret = -EPERM; |
| if (capable(CAP_NET_ADMIN)) { |
| irda_device_set_media_busy(dev, TRUE); |
| ret = 0; |
| } |
| break; |
| |
| case SIOCGRECEIVING: |
| rq->ifr_receiving = bfin_sir_is_receiving(dev); |
| break; |
| |
| default: |
| ret = -EOPNOTSUPP; |
| break; |
| } |
| |
| return ret; |
| } |
| |
| static struct net_device_stats *bfin_sir_stats(struct net_device *dev) |
| { |
| struct bfin_sir_self *self = netdev_priv(dev); |
| |
| return &self->stats; |
| } |
| |
| static int bfin_sir_open(struct net_device *dev) |
| { |
| struct bfin_sir_self *self = netdev_priv(dev); |
| struct bfin_sir_port *port = self->sir_port; |
| int err = -ENOMEM; |
| |
| self->newspeed = 0; |
| self->speed = 9600; |
| |
| spin_lock_init(&self->lock); |
| |
| err = bfin_sir_startup(port, dev); |
| if (err) |
| goto err_startup; |
| |
| bfin_sir_set_speed(port, 9600); |
| |
| self->irlap = irlap_open(dev, &self->qos, DRIVER_NAME); |
| if (!self->irlap) |
| goto err_irlap; |
| |
| INIT_WORK(&self->work, bfin_sir_send_work); |
| |
| /* |
| * Now enable the interrupt then start the queue |
| */ |
| self->open = 1; |
| bfin_sir_enable_rx(port); |
| |
| netif_start_queue(dev); |
| |
| return 0; |
| |
| err_irlap: |
| self->open = 0; |
| bfin_sir_shutdown(port, dev); |
| err_startup: |
| return err; |
| } |
| |
| static int bfin_sir_stop(struct net_device *dev) |
| { |
| struct bfin_sir_self *self = netdev_priv(dev); |
| |
| flush_work(&self->work); |
| bfin_sir_shutdown(self->sir_port, dev); |
| |
| if (self->rxskb) { |
| dev_kfree_skb(self->rxskb); |
| self->rxskb = NULL; |
| } |
| |
| /* Stop IrLAP */ |
| if (self->irlap) { |
| irlap_close(self->irlap); |
| self->irlap = NULL; |
| } |
| |
| netif_stop_queue(dev); |
| self->open = 0; |
| |
| return 0; |
| } |
| |
| static int bfin_sir_init_iobuf(iobuff_t *io, int size) |
| { |
| io->head = kmalloc(size, GFP_KERNEL); |
| if (!io->head) |
| return -ENOMEM; |
| io->truesize = size; |
| io->in_frame = FALSE; |
| io->state = OUTSIDE_FRAME; |
| io->data = io->head; |
| return 0; |
| } |
| |
| static const struct net_device_ops bfin_sir_ndo = { |
| .ndo_open = bfin_sir_open, |
| .ndo_stop = bfin_sir_stop, |
| .ndo_start_xmit = bfin_sir_hard_xmit, |
| .ndo_do_ioctl = bfin_sir_ioctl, |
| .ndo_get_stats = bfin_sir_stats, |
| }; |
| |
| static int bfin_sir_probe(struct platform_device *pdev) |
| { |
| struct net_device *dev; |
| struct bfin_sir_self *self; |
| unsigned int baudrate_mask; |
| struct bfin_sir_port *sir_port; |
| int err; |
| |
| if (pdev->id >= 0 && pdev->id < ARRAY_SIZE(per) && \ |
| per[pdev->id][3] == pdev->id) { |
| err = peripheral_request_list(per[pdev->id], DRIVER_NAME); |
| if (err) |
| return err; |
| } else { |
| dev_err(&pdev->dev, "Invalid pdev id, please check board file\n"); |
| return -ENODEV; |
| } |
| |
| err = -ENOMEM; |
| sir_port = kmalloc(sizeof(*sir_port), GFP_KERNEL); |
| if (!sir_port) |
| goto err_mem_0; |
| |
| bfin_sir_init_ports(sir_port, pdev); |
| |
| dev = alloc_irdadev(sizeof(*self)); |
| if (!dev) |
| goto err_mem_1; |
| |
| self = netdev_priv(dev); |
| self->dev = &pdev->dev; |
| self->sir_port = sir_port; |
| sir_port->dev = dev; |
| |
| err = bfin_sir_init_iobuf(&self->rx_buff, IRDA_SKB_MAX_MTU); |
| if (err) |
| goto err_mem_2; |
| err = bfin_sir_init_iobuf(&self->tx_buff, IRDA_SIR_MAX_FRAME); |
| if (err) |
| goto err_mem_3; |
| |
| dev->netdev_ops = &bfin_sir_ndo; |
| dev->irq = sir_port->irq; |
| |
| irda_init_max_qos_capabilies(&self->qos); |
| |
| baudrate_mask = IR_9600; |
| |
| switch (max_rate) { |
| case 115200: |
| baudrate_mask |= IR_115200; |
| case 57600: |
| baudrate_mask |= IR_57600; |
| case 38400: |
| baudrate_mask |= IR_38400; |
| case 19200: |
| baudrate_mask |= IR_19200; |
| case 9600: |
| break; |
| default: |
| dev_warn(&pdev->dev, "Invalid maximum baud rate, using 9600\n"); |
| } |
| |
| self->qos.baud_rate.bits &= baudrate_mask; |
| |
| self->qos.min_turn_time.bits = 1; /* 10 ms or more */ |
| |
| irda_qos_bits_to_value(&self->qos); |
| |
| err = register_netdev(dev); |
| |
| if (err) { |
| kfree(self->tx_buff.head); |
| err_mem_3: |
| kfree(self->rx_buff.head); |
| err_mem_2: |
| free_netdev(dev); |
| err_mem_1: |
| kfree(sir_port); |
| err_mem_0: |
| peripheral_free_list(per[pdev->id]); |
| } else |
| platform_set_drvdata(pdev, sir_port); |
| |
| return err; |
| } |
| |
| static int bfin_sir_remove(struct platform_device *pdev) |
| { |
| struct bfin_sir_port *sir_port; |
| struct net_device *dev = NULL; |
| struct bfin_sir_self *self; |
| |
| sir_port = platform_get_drvdata(pdev); |
| if (!sir_port) |
| return 0; |
| dev = sir_port->dev; |
| self = netdev_priv(dev); |
| unregister_netdev(dev); |
| kfree(self->tx_buff.head); |
| kfree(self->rx_buff.head); |
| free_netdev(dev); |
| kfree(sir_port); |
| platform_set_drvdata(pdev, NULL); |
| |
| return 0; |
| } |
| |
| static struct platform_driver bfin_ir_driver = { |
| .probe = bfin_sir_probe, |
| .remove = bfin_sir_remove, |
| .suspend = bfin_sir_suspend, |
| .resume = bfin_sir_resume, |
| .driver = { |
| .name = DRIVER_NAME, |
| }, |
| }; |
| |
| module_platform_driver(bfin_ir_driver); |
| |
| module_param(max_rate, int, 0); |
| MODULE_PARM_DESC(max_rate, "Maximum baud rate (115200, 57600, 38400, 19200, 9600)"); |
| |
| MODULE_AUTHOR("Graf Yang <graf.yang@analog.com>"); |
| MODULE_DESCRIPTION("Blackfin IrDA driver"); |
| MODULE_LICENSE("GPL"); |