PCI: Document that most pci options are shared between i386 and x86-64
Since the code is shared pretty much most of the pci= options are shared,
but kernel-parameters.txt marked most of them as i386 only.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt
index 0f1544f..08fbc83 100644
--- a/Documentation/kernel-parameters.txt
+++ b/Documentation/kernel-parameters.txt
@@ -101,6 +101,7 @@
X86-64 X86-64 architecture is enabled.
More X86-64 boot options can be found in
Documentation/x86_64/boot-options.txt .
+ X86 Either 32bit or 64bit x86 (same as X86-32+X86-64)
In addition, the following text indicates that the option:
@@ -1588,7 +1589,7 @@
See also Documentation/paride.txt.
pci=option[,option...] [PCI] various PCI subsystem options:
- off [X86-32] don't probe for the PCI bus
+ off [X86] don't probe for the PCI bus
bios [X86-32] force use of PCI BIOS, don't access
the hardware directly. Use this if your machine
has a non-standard PCI host bridge.
@@ -1596,9 +1597,9 @@
hardware access methods are allowed. Use this
if you experience crashes upon bootup and you
suspect they are caused by the BIOS.
- conf1 [X86-32] Force use of PCI Configuration
+ conf1 [X86] Force use of PCI Configuration
Mechanism 1.
- conf2 [X86-32] Force use of PCI Configuration
+ conf2 [X86] Force use of PCI Configuration
Mechanism 2.
noaer [PCIE] If the PCIEAER kernel config parameter is
enabled, this kernel boot option can be used to
@@ -1618,37 +1619,37 @@
this option if the kernel is unable to allocate
IRQs or discover secondary PCI buses on your
motherboard.
- rom [X86-32] Assign address space to expansion ROMs.
+ rom [X86] Assign address space to expansion ROMs.
Use with caution as certain devices share
address decoders between ROMs and other
resources.
- norom [X86-32,X86_64] Do not assign address space to
+ norom [X86] Do not assign address space to
expansion ROMs that do not already have
BIOS assigned address ranges.
- irqmask=0xMMMM [X86-32] Set a bit mask of IRQs allowed to be
+ irqmask=0xMMMM [X86] Set a bit mask of IRQs allowed to be
assigned automatically to PCI devices. You can
make the kernel exclude IRQs of your ISA cards
this way.
- pirqaddr=0xAAAAA [X86-32] Specify the physical address
+ pirqaddr=0xAAAAA [X86] Specify the physical address
of the PIRQ table (normally generated
by the BIOS) if it is outside the
F0000h-100000h range.
- lastbus=N [X86-32] Scan all buses thru bus #N. Can be
+ lastbus=N [X86] Scan all buses thru bus #N. Can be
useful if the kernel is unable to find your
secondary buses and you want to tell it
explicitly which ones they are.
- assign-busses [X86-32] Always assign all PCI bus
+ assign-busses [X86] Always assign all PCI bus
numbers ourselves, overriding
whatever the firmware may have done.
- usepirqmask [X86-32] Honor the possible IRQ mask stored
+ usepirqmask [X86] Honor the possible IRQ mask stored
in the BIOS $PIR table. This is needed on
some systems with broken BIOSes, notably
some HP Pavilion N5400 and Omnibook XE3
notebooks. This will have no effect if ACPI
IRQ routing is enabled.
- noacpi [X86-32] Do not use ACPI for IRQ routing
+ noacpi [X86] Do not use ACPI for IRQ routing
or for PCI scanning.
- use_crs [X86-32] Use _CRS for PCI resource
+ use_crs [X86] Use _CRS for PCI resource
allocation.
routeirq Do IRQ routing for all PCI devices.
This is normally done in pci_enable_device(),