#
# sensor hub drivers configuration
#

config SENSORS_SSP
	tristate "Sensors ssp"
	default n
	depends on SPI
	help
	  ssp driver for sensor hub.
          If you say yes here you get ssp support for
	  sensor hub.
	  To compile this driver as a module, choose M here: the
	  module will be called ssp.

config SSP_ENG_DEBUG
	tristate "sensor hub eng debug mode"
	default n	
	help	  
	  If you want to use eng debug mode for sensor hub, it should be set.

config SENSORS_SSP_A51
	tristate "Sensors ssp a51"
	default n
	help
	  If you want to use sensor hub for a51 project, it should be set.

config SENSORS_SSP_XCOVERPRO
	tristate "Sensors ssp xcoverpro"
	default n
	help
	  If you want to use sensor hub for xcoverpro project, it should be set.

config SENSORS_SSP_GTA4XL
	tristate "Sensors ssp g4a4xl"
	default n
	help
	  If you want to use sensor hub for g4a4xl project, it should be set.

config SENSORS_SSP_M31
	tristate "Sensors ssp m31"
	default n
	help
	  If you want to use sensor hub for m31 project, it should be set.

config SENSORS_SSP_M21
	tristate "Sensors ssp m21"
	default n
	help
	  If you want to use sensor hub for m21 project, it should be set.

config SENSORS_SSP_M31S
	tristate "Sensors ssp m31s"
	default n
	help
	  If you want to use sensor hub for m31s project, it should be set.

config SENSORS_SSP_GYROFILE_FOR_MAG
	tristate "use gyro cal file for mag cal"
	default n	
	help	  
	  If you want to use gyro cal file for magnetic sensor, it should be set.

config SENSORS_A96T3X6
	depends on I2C
	tristate "A96T3X6 touchkey"
	default n
	help
	  If you say yes here if you use A96T3X6 for grip.
	  This option enables grip sensors using
	  Above A96T3X6 device driver for grip.

config SENSORS_A96T3X6_SUB
	depends on I2C
	tristate "A96T3X6 driver for grip"
	default n
	help
	  Say Y here if you use A96T3X6 for grip.
	  This option enables grip sensors using
	  Above A96T3X6 device driver for grip.

config SENSORS_A96T3X6_WIFI
	depends on I2C
	tristate "A96T3X6 driver for grip"
	default n
	help
	  Say Y here if you use A96T3X6 for grip.
	  This option enables grip sensors using
	  Above A96T3X6 device driver for grip.

config SENSORS_A96T3X6_2CH
	depends on I2C
	tristate "SENSORS_A96T3X6_2CH driver for grip"
	default n
	help
	  Say Y here if you use SENSORS_A96T3X6_2CH for grip.
	  This option enables grip sensors using
	  Above SENSORS_A96T3X6_2CH device driver for grip.

config SENSORS_A96T3X6_WIFI_2CH
	depends on I2C
	tristate "SENSORS_A96T3X6_WIFI_2CH driver for grip"
	default n
	help
	  Say Y here if you use SENSORS_A96T3X6_WIFI_2CH for grip.
	  This option enables grip sensors using
	  Above SENSORS_A96T3X6_WIFI_2CH device driver for grip.

config SENSOR_A96T3X6_LDO_SHARE
	depends on I2C
	tristate "SENSOR_A96T3X6_LDO_SHARE driver for grip"
	default n
	help
	  Say Y here if you use SENSOR_A96T3X6_LDO_SHARE for grip.
	  This option enables grip sensors using
	  Above SENSOR_A96T3X6_LDO_SHARE device driver for grip.

config SENSORS_A96T3X6_CRC_CHECK
	bool "check crc check instead of checksum compare"
	default n
	help
	  Say Y here if you use crc check instead of checksum compare

config SENSORS_FW_VENDOR
	bool "Locate the Firmware on Vendor"
	default n
	help
	  To use the module automatic system, 
	  locate the firmware on vendor side.
	  DO NOT say Y when ABOV GRIP senseors use a common ldo.

config SENSORS_A96T3X6_TABA4XL
	depends on I2C
	tristate "A96T3X6 touchkey"
	default n
	help
	  If you say yes here if you use A96T3X6 for grip.
	  This option enables grip sensors using
	  Above A96T3X6 device driver for grip.

config SENSORS_A96T3X6_M30S
	depends on I2C
	tristate "A96T3X6 touchkey"
	default n
	help
	  If you say yes here if you use A96T3X6 for grip.
	  This option enables grip sensors using
	  Above A96T3X6 device driver for grip.

config SENSORS_A96T3X6_M31
	depends on I2C
	tristate "A96T3X6 touchkey"
	default n
	help
	  If you say yes here if you use A96T3X6 for grip.
	  This option enables grip sensors using
	  Above A96T3X6 device driver for grip.

config SENSORS_A96T3X6_A51
	depends on I2C
	tristate "A96T3X6 touchkey"
	default n
	help
	  If you say yes here if you use A96T3X6 for grip.
	  This option enables grip sensors using
	  Above A96T3X6 device driver for grip.

config SENSORS_A96T3X6_A51_USA
	depends on I2C
	tristate "A96T3X6 touchkey"
	default n
	help
	  If you say yes here if you use A96T3X6 for grip.
	  This option enables grip sensors using
	  Above A96T3X6 device driver for grip.

config SENSORS_TC3XXK
	depends on I2C
	tristate "TC3XXK driver for grip Sensor"
	default n
	help
	  Say Y here if you use TC3XXK IC for grip Sensor.
	  This option enables grip sensors using
	  Coreriver TC305K device driver for grip Sensor.

config SENSORS_SX9360
	depends on I2C
	tristate "SX9360 driver"
	default n
	help
	  Say Y here if you use sx9360.
	  This option enables grip sensors using
	  SemTech sx9360 device driver.
	  Say N here if you do not use sx9360.

config SENSORS_SX9360_SUB
	depends on I2C
	tristate "SX9330 sub driver"
	default n
	help
	  Say Y here if you use sx9330 sub.
	  This option enables grip sensors using
	  SemTech sx9330 sub device driver.
	  Say N here if you do not use sx9330 sub.

config SENSORS_ISG5320A
	depends on I2C
	tristate "ISG5320A grip"
	default n
	help
	  If you say yes here if you use ISG5320A for grip.
	  This option enables grip sensors using
	  IMAGIS ISG5320A device driver for grip.

config SENSORS_ISG5320A_SUB
	depends on I2C
	tristate "ISG5320A grip sub"
	default n
	help
	  If you say yes here if you use ISG5320A_SUB for grip sub.
	  This option enables grip sensors using
	  IMAGIS ISG5320A_SUB device driver for grip sub.
	  
source "drivers/sensorhub/factory/Kconfig"